cc/td/doc/product/wanbu/mgx8260/rel1_2
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Command Reference

Command Reference

The MGX 8260 Media Gateway Media Gateway uses a command line interface for system administration, configuration, and service provisioning. This chapter covers the security requirement, syntax, general description, example, and related topics for each command.

Command Line Interface Guidelines

The MGX 8260 Media Gateway command line interface supports write and read commands. The MGX 8260 Media Gateway command line interface translates write commands to SNMP Set requests. You can often identify write commands by their names—add, delete (del), and change (ch). Read commands are translated into SNMP Get requests, and often have a list (ls) prefix.

Command Syntax

In this document, the command name is shown first in bold type, followed by parameters in italics. If the parameters are optional, they are enclosed in square brackets. In the online Help, parameters are shown in angle brackets.

Optional Parameters

If you do not enter optional parameters for a command, either the default values take effect or there is no change in the optional settings. Default values take effect when you use add commands without the optional parameters. No change is made when you omit parameters for other commands, such as add and change.

You can simply omit optional parameters at the end of a command string, but you must use a # symbol if you omit optional parameters in the middle of a command string.

chds1alm 1.1 # # # 15 144

Security Levels

The MGX 8260 Media Gateway command line interface enforces security with user names, passwords, and access privileges. The Command Modes section of the command reference shows a security level for each command. See Table 2-1 for a definition of these levels.

Understanding Bitmaps

The MGX-8260 command line interface reports some parameters as binary bitmaps. A bitmap is a compact way of representing multiple binary indicators using a single decimal value. To interpret the bitmap, you must convert it to a binary number and then interpret the individual bit positions.

For example, the MGX-8260 Media Gateway reports the card service type as a decimal value that indicates one of four possible service types. To interpret the decimal value, convert it to a binary value using a decimal to binary conversion tool such as the Microsoft Calculator in the scientific mode.

Assume the MGX-8260 command line interface reports a decimal value of 4. The binary equivalent is 0100. Each bit of the binary number is mapped to a specific card service type:


Table 9-1: Binary Bits versus Binary Values
Bit Position

3

2

1

0

Binary Value

0

1

0

0

A bit position is set when it contains a one. In this case, the binary value sets bit position two. To determine the card service state, use the following service translation table:


Table 9-2: Bitmap Translations
Bit position Service

Bit 0

ATM (reserved for future use)

Bit 1

Frame Relay (reserved for future use)

Bit 2

Voice

Bit 3

IP Emulation (reserved for future use)

Therefore, the service state is Voice. In this example the bit positions are mutually exclusive because you can only have one service state at a time. There following values are possible:


Table 9-3: Valid Bitmaps for Service State
Decimal value Binary value Service

1

0001

ATM

2

0010

Frame Relay

4

0100

Voice

8

1000

IP Emulation

The values of other bitmaps, such as alarm bitmaps, are not mutually exclusive, and any value is permitted. The conversion process is the same in both cases.

Using Online Help

The MGX-8260 command line interface includes online help.

Command Syntax Help

To get help for a command, type the command without parameters. For example, to get help on the parameters for the command that adds community strings, type the command without parameters as follows:

addcms

The system responds with a description of the command syntax and parameter definitions as follows:

addcms <commStrCommString> <commStrMgrIpAddr> <commStrPrivilege> commStrCommString: <string> Community String. commStrMgrIpAddr: <string> The manager's IP address associated with this Community String. If it is set to 0.0.0.0, the managers with any IP addresses are allowed. commStrPrivilege: <num> 1: read-only, 2: read-write The manager's privilege for read-only(1) or read-write(2).

Command Summary Help

To get a list of all commands for your user level, type help. To get a list of commands that start with a particular pattern, type help and then the characters to match. For example, the following command lists all commands that begin with add:

help add

acannfile

Activate an announcement file.

acannfile fid

Syntax Description

fid

The announcement file ID. Values: 1-100

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

You use this command to activate an announcement file. To view announcement file ID numbers, use the lsannfiles command.

Examples

The following command activates announcement file 25:

acannfile 25

Related Commands

Command Description

deacannfile

Deactivate an announcement file

rmannfile

Remove an announcement file

lsannfile

List the given announcement file

lsannfiles

List all announcement files

lsdurationif

List duration information about announcement files

addcms

Add the community string that applies to an SNMP manager who subscribes to receive information on traps.

addcms Comm-Str MgrAddr [Privilege]

Syntax Description

Comm-Str

An SNMP community string, such as "Public". Values: string of up to
20 characters.

MgrAddr

The IP address of the SNMP manager who wants to receive trap events. If the management IP address is set to 0.0.0.0, the community string applies to all IP addresses.

Privilege

Read permission. Values: 1 = read-only, 2 = read-write.

Defaults

Privilege: 1

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

You specify the access permission, read-only or read-write, to community strings. You can configure up to 15 community strings.

Examples

The following command adds a public community string with read-write privilege for all SNMP managers:

addcms Public 0.0.0.0 2

Related Commands

Command Description

addtmgr

Add trap manager

delcms

Delete community string

lscms

List community string

lscmss

List community strings

lstmgr

List trap manager

lstmgrs

List trap managers

adddchan

Add a D Channel.

adddchan Index Repetitions DlSapProfile MacSapProfile DS0 DS0format

Syntax Description

Index

The slot and line number, delimited by a period, of the new D Channel.

Repetitions

The number of sequential lines to add. Values: 1 to 1136.

DlSapProfile

The DLSAP profile number associated with the D Channel. Values: 1-10.

MacSapProfile

The MACSAP profile number associated with the D Channel. Values: 1-10.

DS0

The DS0 number for this D Channel. Values: Integer 1-24.

DS0format

The DS0 format for this D Channel. Values: 56 or 64.

Defaults

Repetitions: 1

DlSapProfile: 1

MacSapProfile: 1

DS0: 24

DS0format: 64

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added repetitions and DS0 format parameters.

Usage Guidelines

Use this command to assign a DLSAP (Digital Link Service Access Point) and MACSAP (Media Access Service Access Point) profile to the D Channel. These profiles define the operational characteristics of the channel's protocol stack. Before adding a D channel, you must define MACSAP and DLSAP profiles.

Examples

The following example adds a 56 kpbs D Channel (DS0 = 1) of line 1 on slot 14 using DLSAP profile 2 and MACSAP profile 3:

adddchan 14.1 2 3 1 56

Related Commands

Command Description

adddslp

Add a DLSAP profile

addmacsapprof

Add a MACSAP profile

deldchan

Delete a D Channel

lsdchan

List information about a D Channel

lsdchans

List information about D Channels

adddlsp

Add a DLSAP profile.

adddlsp dlsapProfIndex [dlsapFrameLen dlsapWinSize dlsapRetransCount dlsapCongestionTimer dlsapt200Timer dlsapt203Timer dlsapModulo dlsapTEIAssign dlsapMaxDlcs dlsapTEI]

Syntax Description

dlsapProfIndex

The identifier of a DLSAP Profile. Values: 1 - 20

dlsapFrameLen

The frame length, which is the maximum number of octets in an information field. Values: 1 - 1960

dlsapWinSize

The window size, which is the maximum number of sequentially numbered I-frames that may be outstanding. Values: 1 - 128

dlsapRetransCount

The maximum number of retransmissions of a frame. Values: 1 - 1023

dlsapCongestionTimer

The timer at the end of which DLCs are dropped if the congestion persists. Values: 1 - 1023

dlsapt200Timer

The number of seconds that must expire before initiating a frame. Values: Integer. Values: 1 to 3

dlsapt203Timer

The maximum time allowed without frames being exchanged. Values: Integer.Values 20 to 60

dlsapModulo

The modulus that sequentially numbers each I-frame. Values: 8 or 128

dlsapTEIAssign

The Terminal Endpoint Identifier assignment setting:

  • automatic—TEI is selected by the ASP Layer Management procedure on the network side. Default: 2, which yields a TEI of 1

  • nonAutomatic—TEI is selected by the user

dlsapMaxDlcs

The maximum number of DLCs for this DLSAP. Values: 1 to 16

dlsapTEI

The starting number for reassigning TEIs. This number is used in conjunction with the previous two parameters to number TEIs. For example, if TEI Assignment is nonAutomatic, Maximum DLCs for this DLSAP is 4, and TEI is 14. When a D Channel is added, 4 TEIs starting at 14 are preconfigured. Values: 0 to 63

Defaults

dlsapFrameLen: 1960

dlsapWinSize: 7

dlsapRetransCount: 3

dlsapCongestionTimer: 200

dlsapt200Timer: 1

dlsapt203Timer: 10

dlsapModulo: 128

dlsapTEIAssign: 2

dlsapMaxDlcs: 1

dlsapTEI: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The DLSAP (Digital Link Service Access Point) profile defines a collection of settings for the D Channel protocol stack. These settings describe the operating characteristics of the interface between LAPD and Q.931 call control.

You assign a DLSAP profile when adding a D Channel management path. The window-size parameter, dlsapWinSize, depends on the modulo. For example, if the modulo is 8, then the range of the window size is 1 - 8. If the modulo is 128, then the range is 1 - 128.

Examples

The following example adds a DLSAP profile with default settings:

adddlsp 1

Related Commands

Command Description

deldlsp

Delete a DLSAP profile

lsdlsapstat

List statistics for a DLSAP

lsdlsapstats

List DLSAP statistics

lsdlsapstatus

List status for a DLSAP

lsdlsp

List a DLSAP profile

lsdlsps

List DLSAP profiles

addds1ln

Add DS1 (T1 or E1) lines.

addds1ln Location numOfLines [LineType LineCoding SendCode LoopConfig LineSignalMode XmitClkSrc SignalBits IdleCode]

Syntax Description

Location

The slot and line number, delimited by a period, of the new DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

numOfLines

Number of lines to add. The MGX 8260 stops adding lines at the first failure. Values: 1-1136.

LineType

The type of framing. The T1 values are:

2=dsx1ESF, means use Extended superframe DS1

3=dsx1D4, means use AT&T D4 format

The E1 values are:

4=dsx1E1, means use CCITT Recommendation G.704, Table 4a

5=dsx1E1-CRC, means use CCITT Recommendation G.704, Table 4b

6=dsx1E1-MF, means use G.704 table 4a with TS16 multi-framing enabled

7=dsx1E1-CRC-MF, means use G.704 table 4b with TS16 multi-framing enabled

LineCoding

The line coding format. Not applicable for T1 lines added to the BSC. The valid entries are:

1=dsx1JBZS (reserved for future use)

2=dsx1B8ZS (T1 lines only)

3=dsx1HDB3 (E1 lines only)

4=dsx1ZBTSI (reserved for future use)

5=dsx1AMI

6=other (reserved for future use)

SendCode

The type of code being sent across the DS1 interface by the device. Values are 1 - 8 and have the following names:

1=dsx1SendNoCode

2=dsx1SendLineCode (T1 lines only)

3=dsx1SendPayloadCode (reserved for future use)

4=dsx1SendResetCode (T1 lines only)

5=dsx1SendQRS (T1 lines only)

6=dsx1Send511Pattern (T1 or E1)

7=dsx1Send3in24Pattern (T1 or E1)

8=dsx1Send1in16 (T1 lines only)

LoopConfig

The loopback configuration of the DS1 interface. Values are 1 - 4 and have the following names:

1=dsx1NoLoop

2=dsx1PayloadLoop

3=dsx1LineLoop

4=dsx1OtherLoop, means local loopback on this device

LineSignalMode

Signal mode for transmit direction. In the receive direction, the mode is always set to robbed bit (2). Values are 1 - 4 and have the following names and meanings:

1=none, means reserve no bits and set channel bandwidth to 64 kbps.

2=robbedBit, applies to T1 Channel Associated Signaling. Use a 56 kpps channel for this mode. You can select ABCD bit encoding, but the MGX 8260 does not detect A/B signalling. Echo cancellation is enabled at set-up unless a fax tone is detected.

3=bitOriented, applies to E1 Channel Associated Signaling

4=messageOriented, means Common Channel Signaling either on channel 16 of an E1 line or channel 24 of a T1 line (reserved for future use)

XmitClkSource

The clock source for the transmit signal:

1=Loop Timing, use the recovered receive clock1 (reserved for future use)

2=Local Timing, use the local clock

3=Through Timing (reserved for future use)

SignalBits

The 4-bit signaling pattern, represented by an integer:

1=0000

2=0001

3=0010

4=0011

5=0100

6=0101

. . .

16=1111

IdleCode

The code that is sent on each idle DS0 within the DS1 line. Values: 0-255

1Supported at the SCC through the clock source configuration

Defaults

numOfLines: 1

LineType: 2 for T1 or 7 for E1

LineCoding: 2 for T1 or 3 for E1

SendCode: 1

LoopConfig: 1

LineSignalMode: 1 for T1 and 3 for E1

XmitClkSrc: 2

Signal Bits: 1 for T1 and 6 for E1

IdleCode: 127

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.1

Added BSC

1.2

Added E1 lines

Usage Guidelines

Use this command to add one or more DS1 lines to NSC or BSC circuit cards. Line type affects the line data rate, the number of DS0 channels, and the interpretation of usage and error statistics. NSCs support bothT1 and E1 line types, but you must configure the entire chassis for one type or the other. BSCs support T1 lines only. The system returns an error if you attempt to apply line changes that conflict with the chassis mode. Unspecified parameters, designated by a # symbol, assume the default value

To add lines to a BSC, first add DS3 lines, then add corresponding DS1 lines.


Note   When adding a range of lines, the process stops at the first error.

Examples

The following example adds a DS1 line with AMI line coding to slot 13 line 6:

addds1ln 13.6 # 5

Related Commands

Command Description

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

offbertds1

Stop BERT on DS1

onbertds1

Start BERT on DS1

addds3ln

Add a DS3 line.

addds3ln Location [RepeatLines LineType LineCoding SendCode LoopCfg XmitClkSource CableLength]

Syntax Description

Location

The slot and line number, delimited by a period, of the new DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

RepeatLines

The number of lines you can add in a single request. Values are 1 - 76.

LineType

The type of DS3 C-bit, which affects the interpretation of the usage and error statistics. Values are 1 - 8 and have the following names:

1=dsx3other (reserved for future use)

2=dsx3SYNTRAN (reserved for future use)

3=dsx3M23

4=dsx3CbitParity (reserved for future use)

5=dsx3ClearChannel (reserved for future use)

6=e3other (reserved for future use)

7=e3Framed (reserved for future use)

8=e3Plcp (reserved for future use)

LineCoding

Zero suppression used on this interface.The line coding dsx3B3ZS and e3HDB3 refers to patterns of normal bits and bipolar violations that are used to replace sequences of zero bits of a specified length. Values are 1 - 3 and have the following names:

1=dsx3Other

2=dsx3B3ZS

3=e3HDB3 (reserved for future use)

SendCode

The type of code being sent across the DS3/E3 interface by the device. (Optional for E3 interfaces.) Values are 1 - 6 and have the following names and meanings:

1=dsx3SendNoCode, sending looped or normal data

2=dsx3SendLineCode, sending a request for a line loopback

3=dsx3SendPayloadCode, sending a request for a payload loopback (all DS1/E1s in a DS3/E3 frame)

4=dsx3SendResetCode, sending a loopback deactivation request

5=dsx3SendDS1LoopCode, requesting to loopback a particular DS1/E1 within a DS3/E3 frame

6=dsx3SendTestPattern, sending a test pattern

LoopConfig

The loopback configuration of the DS3/E3 interface. Values are 1 - 4 and have the following names:

1=dsx3NoLoop

2=dsx3PayloadLoop

3=dsx3LineLoop

4=dsx3OtherLoop

XmitClockSource

The transmit clock source, which is derived from the recovered receive clock of another DS3 interface. Values are 1-3 and have the following names:

1=loopTiming

2=localTiming

3=throughTiming

CableLength

One of the following ranges of lengths for the cable:

1=1 to 225 ft

2=225 to 300 ft

3=300 to 450 ft

4=450 to 900 ft

Defaults

RepeatLines: 1

LineType: 3

LineCoding: 2

SendCode: 1

LoopConfig: 1

XmitClockSource: 2

CableLength: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card configuration - no functional change

Usage Guidelines

Use this command to add one or more DS3 lines to BSC or DMC circuit cards. If you do not enter optional parameters the default value is used.


Note   When adding a range of lines, the process stops at the first error.

Examples

The following example adds a DS3 line on the BSC at slot 11 line 501, using all the default settings.

addds3ln 11.501

Related Commands

Command Description

chds3alm

Change DS3 alarm severity and threshold

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List DS3 current statistics

lsds3intst

List DS3 interval statistics

lsds3ln

List DS3 line

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

addereg

Add email registration.

addereg Index Address Trap#1 [Trap#2 ... Trap#20]

Syntax Description

Index

A unique number that identifies one of the ten users. Values: 1-10.

Address

The email address, up to 40 characters, of the person who wants to receive email about traps. For example, admin@cisco.com.

Trap

The number of the trap condition to register. When the trap occurs, the system sends an email to the user. Trap numbers start at 1000 and map directly to alarms and events. You must specify at least one trap.

Values: One to twenty existing trap numbers. For more information of trap numbers, see the "Alarm Surveillance."

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to specify up to 20 traps to monitor.

Examples

The following example registers user 1 for major shelf and EMM alarms:

addereg 1 user@domain.com 1000 1800

Related Commands

Command Description

chem

Configure email registration

chereg

Change email registration

delereg

Delete email registration

lsem

List email server

lsereg

List entry registered

lseregs

List registered email alerts

addethln

Add Ethernet line.

addethln Location Addr [Prim_IPGW_Addr AddTargetState RDP Mask Mode]

Syntax Description

Location

The slot and line number, delimited by a period, of the new Ethernet line. Slot values: 9 Line values: 1-4.

Addr

IP Address in dot notation w.x.y.z.

Prim_IPGW_Addr

The IP address of the primary gateway for the interface.

AddTargetState

The state, active or inactive, of the line after the line is added. Values: 1 = active, 2 = inactive.

RDP

The state of the Router Discovery Protocol. Values: 1 = disabled, 2 = enabled.

Mask

The subnet mask in dotted notation a.b.c.d.

Mode

The mode of the line. Values: 1 = Half duplex, 2 = Full duplex.

Defaults

AddTargetState: 1

RDP: 1

Mode: 2

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to add Ethernet lines to the Fast Ethernet SCC and backcard.

Examples

The following example adds an Ethernet interface to the MGX 8250 Media Gateway at slot 7 line 1, address 10.1.2.10, and specifies the primary gateway to use.

addethln 9.1 10.1.2.10 10.1.1.8

Related Commands

Command Description

delethln

Delete Ethernet line

chethln

Change Fast Ethernet line

upethln

Activate Ethernet line

dnethln

DeActivate Ethernet line

lsethln

List Ethernet line

lsethlns

List Ethernet Lines

addiproute

Add an IP route.

addiproute IPRouteDestination nexthop IPRouteMask

Syntax Description

IPRouteDestination

The destination IP address of this route. An entry of 0.0.0.0 is considered a default route.

nexthop

The IP address of the next hop of this route. If a route is bound to an interface (through a broadcast media), the value of this field is the agent's IP address on the interface.

mask

The mask to be logically ANDed with the destination address before being compared to the value in the IPRouteDest field.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to add a static route to a remote destination. For systems that do not support arbitrary subnet masks, the system constructs the value mask by determining the network class:

mask network

255.0.0.0

class-A

255.255.0.0

class-B

255.255.255.0

class-C

Examples

The following example adds a static route to 172.16.1.1 through 10.1.1.1:

addiproute 172.16.1.1 10.1.1.1 255.0.255.0.

Related Commands

Command Description

deliproute

Delete an IP route

lsiproute

List an IP route

lsiproutes

List IP routes

addm13

Add map to DS1 from DS3.

addm13 SrcDS3LineNum SrcDS1LineNum DestDS1SlotNum DestDS1LineNum [NoOfLines]

Syntax Description

SrcDS3LineNum

The number of the source DS3 line. Values: 1 - 6.

SrcDS1LineNum

The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28.

DestDS1SlotNum

The logical slot number for the destination NSC card. When mapping a range of DS1 lines, this is the starting slot. Values: 1-6 and 11-16.

DestDS1LineNum

The number of the DS1, or starting DS1, in the NSC. Values: 1-16

NoOfLines

The number of map pairs to add. Values: 1-192, depending on existing mapping. To map a single point, omit this argument.

Defaults

NoOfLines: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to add one or more DS3 to DS1 mappings from Distribution Matrix Card (DMC) to the Narrowband Service Card (NSC). To map a single point, omit the NoOfLines argument.

Examples

For example, in an MGX 8260 Media Gateway without any existing mapping, specify the maximum number of mappings as follows:

addm13 1 1 1 1 192

To add three map entries, enter the following command:

addm13 1 3 1 1 3

Related Commands

Command Description

chm13

Change DS1 to DS3 map

delm13

Delete DS1 to DS3 map

lsm13

List DS3-to-DS1 mapping

lsm13s

List DS3-to-DS1 mappings

addmacsapprof

Add a MACSAP profile.

addmacsapprof Index [sapIf LinkArb LapdType MaxOutStFrames TimQUpperThresh TimeQLowerThresh ConnTimer t201Timer t202Timer TEICheckTimer N202 LowAutoTei KeepL1Up]

Syntax Description

Index

The identifier of a MAC SAP. Values: 1 - 20.

sapIf

The logical Interface. Values: 1 = user, 2 = network.

LinkArb

Link setup arbitration scheme. Values: 1 = passive, 2 = active.

LapdType

The type of LAPD interface. Values: 1 - 19, which have the following mnemonics that, in most cases,. imply their meanings:

1=test

2=ccitt

3=att5EssBRA

4=att5EssPRA

5=att4Ess

6=ntDMS100BRA

7=ntDMS100PRA

8=vn2or3

9=insNet

10=tr6MPC

11=tr6PBX

12=ausb (Austel Basic)

13=ausp (Austel Primary)

14=nISDN1 (National ISDN-1)

15=etsi

16=bc303TMC (Bellcore tr303 tmc)

17=bc303CSC

18=ntDMS250

19=bellcore

MaxOutStFrames

Maximum number of sequentially numbered I-frames that may be outstanding. Values: 1 - 255.

TimQUpperThresh

The timer queue upper threshold for the I-frame queue. When the I-frame queue size exceeds this threshold, the congestion timer is started and flow-control is turned on. Values: 1 to 32767

TimeQLowerThresh

The timer queue lower threshold for I-frame queue. When the I-frame queue size falls below this threshold, the congestion timer is stopped and flow-control is turned off. Values: 1 to 32767

ConnTimer

The connection timer. Values: 1 -1024.

t201Timer

The T201 timer value. Values: 1 to 1024

t202Timer

The T202 timer value. Values: 1 to 1024

TEICheckTimer

The setting of the TEI check timer. Values: 1 - 1025. 1025 = disabled.

N202

The maximum number of transmissions of a TEI Identity request message.

LowAutoTei

The value that is greater than or equal to the lowest automatic TEI that the ASP can allocate. Applicable only when configured for automatic TEI assignment. Values: 1 to 127

KeepL1Up

A setting that keeps MAC up all the time if True. Values:

1 = False

2 = True

Defaults

sapIf: 2

LinkArb: 2

LapdType: 2

MaxOutStFrames: 7

TimQUpperThresh: 1000

TimeQLowerThresh: 100

ConnTimer: 500

t201Timer: 1

t202Timer: 2

TEICheckTimer: 5

N202: 3

LowAutoTei: 64

KeepL1Up: 2

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

You assign a MACSAP (Media Access Service Access Point) profile when adding a D Channel management path to define a collection of settings for the D Channel protocol stack. These settings describe the operating characteristics of the interface between LAPD and the physical layer.

Examples

The following example adds a MACSAP profile with default settings:

addmacsapprof 1

Related Commands

Command Description

delmacsapprof

Delete a MACSAP profile

lsmacsapprof

List information about a MACSAP profile

lsmacsapprofs

List all MACSAP profiles

lsmacsapstat

List statistics for a MACSAP interface

lsmacsapstats

List MACSAP statistics

addreds

Add card redundancy.

addreds PrimarySlot SecondarySlot

Syntax Description

PrimarySlot

Physical location of the primary card in the chassis. Valid settings: 1-8 and 11-16.

SecondarySlot

Physical location of the secondary card in the chassis. Valid settings: 1-8 and 11-16.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Adds card redundancy between the primary and secondary slot. If the primary fails, the secondary takes over.

Examples

The following example makes card 3 the redundant card and card 1 the primary card.

addreds 1 3

Related Commands

Command Description

delreds

Delete a card redundancy pair

lsreds

List redundancies

swcd

Switch to redundant NSC

addsess

Add an MGCP session manager.

addsess SessionSetId GroupId SessionId LocalAddr LocalPort RemoteAddr RemotePort Priority

Syntax Description

SessionSetId

The index of the session set to which the group containing the session manager belongs. Values: 1-6.

GroupId

The index of the session group to which the session manager belongs. Values: 1 or 2.

SessionId

The index of this session. Values: 1 or 2

LocalAddr

The local IP address of the session.

LocalPort

Local UDP Port. Values: greater than 1024

RemoteAddr

Remote IP address of the session.

RemotePort

Remote UDP port. Values: greater than 1024

Priority

Session priority. Values: greater than or equal to 0

Defaults

Priority: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

MGCP sessions are communication links between the MGX 8260 and the primary and secondary Media Gateway Controller. Sessions are members session groups, which in turn, are members of session sets. To ensure reliable operation, set up two sessions to each controller through two networks.

Examples

The following example adds session manager 1 to group 1 of set 1:

addsess 1 1 1 10.15.38.233 7007 10.15.38.234 7007

Related Commands

Command Description

addsset

Add a session set

addsgrp

Add a session group

delsess

Delete a session manager

delsset

Delete a session set

delsgrp

Delete a session group

addsgrp

Add an MGCP session group.

addsgrp GroupSetId GroupId

Syntax Description

GroupSetId

The index of the set to which this group belongs. Values: 1-6

GroupId

The index of the session group to which the session manager belongs. Values: 1 or 2.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

MGCP session groups organize session managers into logical groups. A session group contains a collection of sessions that communicate with a single MGC.

Examples

The following example adds session group 1 to session set 1:

addsgrp 1 1

Related Commands

Command Description

addsess

Add a session

addsset

Add a session set

delsess

Delete a session

delsset

Delete a session set

delsgrp

Delete a session group

addsonetln

Add a SONET line.

addsonetln Location [numOfLines MediumType LoopConfig HCSmasking PayloadScrambling FrameScrambling TxClockSource]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

numOfLines

The number of lines to add. Values: 1-4.

MediumType

The type of circuit:

1=SONET

2=SDH (reserved for future use)

LoopConfig

The loopback state:

1=No loop

2=Line loop

3=Serial loop

4=Parallel loop

HCSmasking

The HCS masking state (reserved for future use)

PayloadScrambling

The payload scrambling state:

1=Disable

2=Enable

FrameScrambling

The frame scrambling state:

1=Disable

2=Enable

TxClockSource

The clock source for the transmit signal:

1=Loop Timing, use the recovered receive clock

2=Local Timing, use the local clock

3=Through Timing (reserved for future use)

Defaults

numOfLines: 1

MediumType: 1

LoopConfig: 1

PayloadScrambling: 1

FrameScrambling: 1

TxClockSrc: 2

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure optical SONET/SDH interfaces on the OC-3 SCC and back card. Although the SCC may occupy physical slots 9 or 10, you always configure logical slot 9.

You can add a single line or a range of identically-configured lines with this command. The system adds lines one at a time and aborts on the first failure, even if subsequent additions could have succeeded. The system issues an error message for partially fulfilled requests.

Examples

The following example adds a SONET line with default settings:

addsonetln 9.1

Related Commands

Command Description

chsonetln

Change a SONET line

delsonetln

Delete a SONET line

lssonetln

List information about a SONET line

lssonetlns

List information about all SONET lines

addsrt

Add static route

addsrt Destination Slot.Line [RoutePriority]

Syntax Description

Destination

The IP address of a remote network with which you want a static route. The last byte of the IP number must be zero. For example, 127.2.4.0 is valid

Slot.Line

The slot and line number, delimited by a period, of the origin of the static route. Since the outgoing interface is always an Ethernet line, valid slots are 9-10 and valid lines are 1-4

RoutePriority

Priority for the route entry. Values: 1 - 10, 1 = highest

Defaults

RoutePriority: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use to configure a static route from an MGX 8260 line to a network IP address. If the last byte of the destination address is not 0, the static route is not set. You can configure static routes for empty slots or non-existing lines, but the changes have no effect without the necessary hardware.

Examples

The following example configures a static route from slot 1 line 1 of the MGX 8260 chassis to IP address 12.1.1.0.

addesrt 12.1.1.0 9.1

Related Commands

Command Description

delsrt

Delete static route

lssrt

List static route

lssrts

List static routes

addsset

Add an MGCP session set.

addsset SessSetId MinSlot MinLine MaxSlot MaxLine RedunMode

Syntax Description

SessSetId

Session set index. Values: 1-6.

MinSlot

The minimum slot number within the MGX 8260 Media Gateway chassis assigned for this session set. Values: 1-8 and 11-16.

MinLine

The minimum line number assigned for this Session Set. Values: 1-168 for the BSC; 1-16 for the NSC.

MaxSlot

The maximum slot number within the MGX 8260 Media Gateway chassis assigned for this session set. Values: 1-8 and 11-16.

MaxLine

The maximum line number assigned for this session set. Values: 1-168 for the BSC; 1-16 for the NSC.

RedunMode

The redundancy mode. Values: 1 or 2 as follows.

1=nonFaultTolerant, where the system can have one session group only to a single MGC

2=faultTolerant, where the system can have one or two session groups to redundant MGCs

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Session sets contain a collection of session groups and managers that control a range of MGX 8260 lines. One or two session sets are adequate for a single MGX 8260 chassis.

Examples

The following example adds session set 1 for slots 1-168 of the BSC in slot 11:

addsset 1 11 1 11 168 1

Related Commands

Command Description

addsess

Add a session manager

addsset

Add a session set

delsess

Delete a session manager

delsset

Delete a session set

delsgrp

Delete a session group

addtmgr

Add trap manager.

addtmgr Addr [Port Interface Com_String Bitmap]

Syntax Description

Addr

The IP address of the SNMP manager who wants to receive trap events.

Port

UDP number of port to which the traps are transmitted.

Interface

The default interface for initially sending traps if the routing table has no trap manager. Values: 1, 2, 3. These values have the following names and meanings:

1=scc-eth-if—The default system Ethernet management interface on SCC.

2=inband-if—The in-band management interface on Fast Ethernet.

Com_String

SNMP community string for the trap manager.

Bitmap

A bitwise specification of trap categories to subscribe. Each bit represents a category of traps. Bit values: 1 = subscribe 0, = do not subscribe. Trap Subscription Bitmap specifications are:

Bit 0=Major (trap severity selection)

Bit 1=Minor (trap severity selection

Bit 2=Information (trap severity selection)

Bit 3=Shelf

Bit 4=Card

Bit 5=SNMP

Bit 6=Dsx1 Line

Bit 7=Dsx3 Line

Bit 8=Sonet Line

Bit 9=Ethernet Line

Bit 10=Voice Port

Bit 11=Ethernet Channel

Bit 12=Voice Channel

Bit 13=EMM

Bit 14=Clock

Bit 15=DSP

Bit 16=DMCMAP

Bit 17=ISDN

Bit 18=MGCP

Bit 19=Backhaul Session

The first three bit positions indicate which trap severity categories they are interested in. If you specify severity without specifying any other trap categories, managers receive traps from all categories.

Defaults

Port: 162

Interface: 1

Com_String: "public"

Bitmap: 0

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added new traps

Usage Guidelines

Network administrators can receive email notifications for up to 20 trap events. Use this command to subscribe a manager to receive notification about specific trap events.

Examples

The following example subscribes the manager at address 10.1.1.10 and udp port 162 to receive minor and informational messages for cards and DS1 lines.

The bitmap is a binary number that represents the following settings:

Trap dsx1line SNMP Card Shelf Information Minor Major
Bit Value

1

0

1

0

1

1

0

Bit Position

6

5

4

3

2

1

0

To use this bitmap, convert it to a decimal value and specify it as the last argument. Binary 1100110 is 86 decimal. Therefore, you enter the command as follows:

addtmgr 10.1.1.10 162 2 public 86

The 2 in the third argument sets the in-band interface as the default interface for sending traps when the routing table has no trap manager.

Related Commands

Command Description

addcms

Add community string

chtmgr

Change trap manager

deltmgr

Delete trap manager

lstmgr

List trap manager

lstmgrs

List trap managers

addusp

Add user profile.

addusp Name Access_Level

Syntax Description

Name

The login name of the new user, expressed as a case-sensitive alphanumeric string of four to ten characters. Special characters such as @, #, and $ are allowed.

Access_Level

A value associated with a user profile that determines access rights to the MGX-8260 CLI and WebViewer.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The MGX 8260 Media Gateway enforces security with user accounts and access levels. Users must log onto the MGX 8260 Media Gateway before performing any task, and authenticated users can perform only those tasks permitted by their access level. The MGX 8260 Media Gateway supports up to 20 user accounts, each with access privileges ranging from full control to guest. Initially, the password is the same as the user name, so instruct new users to change their password to a personal one using the chpwd command. The following table summarizes access levels:

Access
Level
Account Type Command Groups

1

SuperUser

Access all features

2

Administrator

Configure and view all features except user profiles and community strings

3

Provisioning

Configure and view system, port, lines, end points, and connections

4

Maintenance

Access selected level 3 commands

5

Operator

View system, port, lines, end points, and connections

6

Guest

View system, common lines and ports

Users can use commands that have an access level equal to or greater than their account access level. For example, a user account with an access level 4 can use all commands with access levels of 4, 5, and 6.

Examples

The following example adds a user named william with Administrator level privileges.

addusp william 2

Related Commands

Command Description

chkey

Change file key

delusp

Delete user profile

addvport

Add voice port.

addvport SlotNum PortNum LineNum DS0Num [RepititionNum WrapNum Dejitter DejitterBufLen Maxdj Mindj PacketLoading EchoTail]

Syntax Description

SlotNum

The logical slot number of an NSC. Values: 1 to 16

PortNum

The logical port number for the new port. Values: 1 to 512

LineNum

The number of the DS1/E1 line for the voice port. Values: 1 to 16

DS0Num

The number of the DS0 within the DS1/E1 for the new port. Values: 1 to 24 for DS1 and 1 to 30 for E1.

RepititionNum

The number of ports to add. Values: 1 to 6944. This corresponds to 31 ports per line, 16 lines per NSC, and 14 NSCs.

WrapNum

The DS0 number at which to wrap to the next slot. Set this to the maximum number of DS0s the NSC in your configuration. For DS1 use 384 and for E1 use 480 with CAS or 496 without CAS. Values: 1 to 512

Dejitter

The desired state, disabled or enabled, of the dejitter buffer. Values: 1 or 2 for disabled and enabled, respectively.

DejitterBufLen

The initial length of the dejitter buffer, specified in multiples of 10 msec. Values: 1 through Maxdj.

Maxdj

The maximum length of the dejitter buffer, specified in multiples of 10 msec. Values: 1 through 50.

Mindj

The minimum length of the dejitter buffer, specified in multiples of 10 msec. Values: 1 through DejitterBufLen.

PacketLoading

The IP packet loading time for voice service, expressed in multiples of 10 msec. Values: 1 - 10.

EchoTail

The length of the echo cancel tail:

1 = echo disabled

2 = tail24ms—24 msecs

3 = tail32ms—32 msecs

4 = tail48ms—48 msecs

5 = tail64ms—64 msecs

6 = tail80ms—80 msecs

6 = tail96ms—96 msecs

7 = tail112ms—112 msecs

8 = tail128ms—128 msecs

Defaults

ReptitionNum: 1

WrapNum: 384 for DS1, 480 for E1 (CAS on)

Dejitter: disabled

DejitterBufLen: 2

Maxdj: 50

Mindj: 1

PacketLoading: 1

EchoTail: 5

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added repetition and wrap arguments

Usage Guidelines

Use this command to add one or more voice ports. The DS1/E1 line must already exist before using this command.

Examples

For example, to add logical voice port 4 using DS0 4 of DS1 line 1 in slot 13, type the following command:

addvport 13 4 1 4

Related Commands

Command Description

chvport

Change voice port

delvport

Delete voice port

lsvport

List voice port

lsvports

List voice ports

bye

Log out.

bye

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Type this command to log out from the MGX 8260 Media Gateway

Examples

The following command logs out.

bye

Related Commands

Command Description

exit

Logs out from the MGX 8260 Media Gateway.

logout

Logs out from the MGX 8260 Media Gateway.

chcdif

Configure card interface.

chcdif Card Mode

Syntax Description

Card

The number of an NSC card.

Mode

Indicates whether the Narrowband Service Card (NSC) transmits and receives traffic through the back card or redirected through the backplane from the DC3 interface on the Distribution Matrix Card (DMC). Values:

1=back card

2=back plane

3=not applicable (no back card)

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the interface mode of the sixteen DS1 interfaces on an NSC. Changing the interface mode resets the card.

Examples

The following example changes the interface mode of card 1 to back plane mode and consequently resets the NSC.

chcdif 1 2

Related Commands

Command Description

clrcdcnf

Clear configuration of a card

chcsbaynum

Change control server bay number (reserved for future use).

chcsbaynum Number

Syntax Description

Number

A string that represents the CS bay number. Values: a string of exactly 8 characters.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Configures the string that identifies the bay number of the MCS.

Examples

The following example changes the bay number of the call server to 2.

chcsbaynum 00000002

Related Commands

Command Description

chcsid

Change control server system ID

chcsid

Change control server system ID (reserved for future use).

chcsid ID

Syntax Description

ID

The system ID of the MCS. Value: user-defined text string, up to 24 characters

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure a user-defined identifier for the MCS.

Examples

The following example changes the bay number of the call server to 2.

chcsid 1234567890

Related Commands

Command Description

chcsbaynum

Change control server bay number

chcsnumfor

Specify the MCS numbering format for modules, lines and channels (reserved for future use).

chcsnumfor format

Syntax Description

format

Specification to start module, line, and channel numbering at 0 or 1.

1 = One-based

2 = Zero-based

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Specifies the MCS interpretation of module, line and channel numbers on an MGX 8260 Media Gateway. For example, you can specify DS0 numbers as 0-23 or 1-24

Examples

The following example specifies a zero-based number format.

chcsnumfor 2

Related Commands

Command Description

chcsbaynum

Change control server bay number

chcstype

Change control server type (reserved for future use).

chcstype type

Syntax Description

type

An alphanumeric string. The string must be exactly 9 characters in length.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Configures the string used to identify the manufacturer and model of the MCS.

Examples

The following example sets the string identifier to "CiscoType"

chcstype CiscoType

Related Commands

Command Description

chcsbaynum

Change control server bay number

chdate

Change date.

chdate date

Syntax Description

date

The system date expressed as mm/dd/yyyy. Values: 1970 - 2099

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure or change the system date.

Examples

The following example sets the system date to January 14, 2001.

chdate 01/14/2001

Related Commands

Command Description

chtime

Change time

chtimezn

Change system time zone

lsdate

List date

chds1alm

Change DS1 alarm severity and thresholds.

chds1alm Location [Red_Severity RAI_Severity Perf_Alarm_Severity LCV_15 LCV_24 LES_15 LES_ 24 LESES_15 LESES_24 SEFS_15 SEFS_24 PSAS_15 PSAS_24 UAS_15 UAS_24
PCV_15 PCV_24 PES_15 PES_24 SES_15 SES_24 BES_15 BES_24 PCSS_15 PCSS_24

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line

Red_Severity

The near end LOF indication, either minor or major. Values: 1 or 2, respectively.

RAI_Severity

The remote alarm indication, either minor or major. Values: 1 or 2, respectively.

Perf_Alarm_Severity

The performance alarm indication, either minor or major. The performance alarm is set if any of the thresholds is exceeded. Values: 1 or 2, respectively.

LCV_15

The line threshold for code violations in a 15-minute window or sliding 24-hour window. A code violation is either a bipolar violation or excessive zeroes event.

LCV_24

LES_15

The line threshold for errored seconds in a 15-minute window or sliding 24-hour window. An errored second is any second with at least one code violation.

LES_ 24

LESES_15

The line threshold for severely errored seconds in a 15-minute window or sliding 24-hour window. A severely errored second is any second with 15 or more code violations.

LESES_24

SEFS_15

The threshold for severely errored framing seconds in a 15-minute window or sliding 24-hour window. A severely errored framing second is a count of one-second intervals containing one or more SEF events.

SEFS_24

PSAS_15

The threshold for PSA seconds in a 15-minute window or sliding 24-hour window. An alarm indication signal second is a count of one-second intervals containing one or more incoming AISs.

PSAS_24

UAS_15

The threshold for unavailable seconds in a 15-minute window or sliding 24-hour window. Unavailable seconds represent the number of seconds that the interface is unavailable.

UAS_24

PCV_15

The threshold for path code violations in a 15-minute window or sliding 24-hour window.

PCV_24

PES_15

The threshold for path errored seconds in a 15-minute window or sliding 24-hour window.

PES_24

PSES_15

The threshold for path severely errored seconds in a 15-minute window or sliding 24-hour window.

PSES_24

BES_15

The threshold for bursty errored seconds in a 15-minute window or sliding 24-hour window.

BES_24

PCSS_15

The threshold for path controlled slip seconds in a 15-minute window or sliding 24-hour window.

PCSs_24

Defaults

No default behavior or values. The following defaults apply to a new DS1 line:

Red_Severity: 2

RAI_Severity: 1

Perf_Alarm_Severity: 1

LCV_15: 14

LCV_24: 134

LES_15: 12

LES_24: 121

LSES_15: 10

LSES_24: 100

SEFS_15: 2

SEFS_24: 17

PSAS_15: 2

PSAS_24: 17

UAS_15: 10

UAS_24: 10

PCV_15: 35

PCV_24: 50

PES_15:35

PES_24:50

PSES_15: 35

PSES_24: 50

BES_15: 35

BES_24: 50

PCSS_15: 35

PCSS_24: 50

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added new alarms

Usage Guidelines

Use this command to change the configuration settings for alarm severity, performance integration period, and thresholds for various error conditions, such as LCV, LES, and LSES. All counter thresholds are integers greater than zero. For details, refer to Table 6-1. If you do not enter optional parameters for a threshold, that threshold is not changed.

Examples

The following example changes the 15-minute LCV thresholds for line 1 of slot 1 from the default value to 15.

chds1alm 1.1 # # # 15

Related Commands

Command Description

addds1ln

Add DS1 line

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 line current statistics

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 line total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

chds1ln

Change DS1 (T1 or E1) lines.

chds1ln Location numOfLines [LineType LineCoding SendCode LoopConfig LineSignalMode XmitClkSrc SignalBits IdleCode]

Syntax Description

Location

The slot and line number, delimited by a period, of the new DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

numOfLines

Number of lines to add. The MGX 8260 stops adding lines at the first failure. Values: 1-1136.

LineType

The type of framing. The T1 values are:

2=dsx1ESF—means use Extended superframe DS1

3=dsx1D4—means use AT&T D4 format

The E1 values are:

4=dsx1E1—means use CCITT Recommendation G.704, Table 4a

5=dsx1E1-CRC—means use CCITT Recommendation G.704, Table 4b

6=dsx1E1-MF—means use G.704 table 4a with TS16 multi-framing enabled

7=dsx1E1-CRC-MF—means use G.704 table 4b with TS16 multi-framing enabled

LineCoding

Theline coding format. Not applicable for T1 lines added to the BSC. The valid entries are:

1=dsx1JBZS (reserved for future use)

2=dsx1B8ZS (T1 lines only)

3=dsx1HDB3 (E1 lines only)

4=dsx1ZBTSI (reserved for future use)

5=dsx1AMI

6=other (reserved for future use)

SendCode

The type of code being sent across the DS1 interface by the device. Values are 1 - 8 and have the following names:

1=dsx1SendNoCode

2=dsx1SendLineCode (T1 lines only)

3=dsx1SendPayloadCode (reserved for future use)

4=dsx1SendResetCode (T1 lines only)

5=dsx1SendQRS (T1 lines only)

6=dsx1Send511Pattern (T1 or E1)

7=dsx1Send3in24Pattern (T1 or E1)

8=dsx1Send1in16 (T1 lines only)

LoopConfig

The loopback configuration of the DS1 interface. Values are 1 - 4 and have the following names:

1=dsx1NoLoop

2=dsx1PayloadLoop

3=dsx1LineLoop

4=dsx1OtherLoop, means local loopback on this device

LineSignalMode

Signal mode for transmit direction. In the receive direction, the mode is always set to robbed bit (2). Values are 1 - 4 and have the following names and meanings:

1=none—means reserve no bits and set channel bandwidth to 64 kbps.

2=robbedBit—applies to Channel Associated Signaling. Use a 56 kpps channel for this mode. You can select ABCD bit encoding, but the MGX 8260 does not detect A/B signalling. Echo cancellation is enabled at set-up unless a fax tone is detected.

3=bitOriented—means E1 Channel Associated Signaling

4=messageOriented=means Common Channel Signaling either on channel 16 of an E1 link or channel 24 of a T1 (reserved for future use)

XmitClkSrc

The clock source for the transmit signal:

1=Loop Timing—use the recovered receive clock (reserved for future use)

2=Local Timing—use the local clock

3=Through Timing (reserved for future use)

SignalBits

The 4-bit signaling pattern, represented by an integer:

1=0000

2=0001

3=0010

4=0011

5=0100

6=0101

. . .

16=1111

IdleCode

The code that is sent on each idle DS0 within the DS1 line. Values: 0-255

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added E1 lines

Usage Guidelines

Use this command to reconfigure one or more DS1 lines on NSC or BSC circuit cards. NSCs support both T1 and E1 lines, but you must configure the entire chassis for one type or the other. The system returns an error if you attempt to apply line changes that conflict with the chassis mode. BSCs support T1 channels only.

For example, the following command activates a local diagnosis loopback on line 1 of logical slot 1:

chds1ln 1.1 # # # # 4

The following example configures 3 DS1 lines beginning at slot 1 line 1 to have a send code of dsx1SendPayloadCode.

chds1ln 1.1 3 # # 3

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

clrds1lnst

Clear DS1 line statistics

chsyslnmd

Change the DS1 line mode

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 line current statistics

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 line total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

offbertds1

Stop BERT on DS1

onbertds1

Start BERT on DS1

chds1lnecho

Configure the echo canceller for a DS1 line.

chds1lnecho Location State

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

State

The enabled or disabled state of the echo canceller for each line. Values:

1 = disable

2 = enable

3 = not applicable

Defaults

State: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to enable or disable the echo canceller for the specified DS1 line. You must activate IPDC on BSC cards to enable or disable echo cancelling. Under MGCP, you can't configure echo cancelling for BSC or NSC cards, so State is fixed at 3 (not applicable).

Examples

The following example enables echo cancelling on slot 12, line 1 of the BSC card.

chds1lnecho 12.1 1

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chds3alm

Change DS3 alarm severities and performance alarm thresholds.

chds3alm Location RedSeverity RAISeverity PerfAlmSeverity NEAlarmUpCount NEAlarmDownCount NEAlarmThreshold LCV15MinThreshold LCV24HrThreshold LES15MinThreshold LES24HrThreshold PCV15MinThreshold PCV24HrThreshold PES15MinThreshold PES24HrThreshold PSES15MinThreshold PSES24HrThreshold SEFS15MinThreshold SEFS24HrThreshold AISS15MinThreshold AISS24HrThreshold UAS15MinThreshold UAS24HrThreshold CCV15MinThreshold CCV24HrThreshold CES15MinThreshold CES24HrThreshold CSES15MinThreshold CSES24HrThreshold

Syntax Description

Location

The slot and line number, delimited by a period, of the DS3 line. Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

RedSeverity

The RED alarm severity. Values: 1 or 0 (major or minor, respectively).

RAISeverity

The RAI alarm severity. Values: 1 or 0 (major or minor, respectively).

PerfAlmSeverity

The performance alarm severity. The performance alarm is set if any of the thresholds is exceeded.Values: 1 or 0 (major or minor, respectively).

Alarm Thresholds:

NEAlarmUpCount

Increment value for the Near End alarm integration counters. The local alarms are LOS and LOF. Values: Integers > zero.

NEAlarmDownCount

Decrement value for the Near End alarm integration counters. The local alarms are LOS and LOF. Values: Integers > zero.

NEAlarmThreshold

Value of the alarm integration counter that raises an alarm. Values: Integers > zero.

LCV15MinThreshold

The threshold for line coding violations in a 15-minute window or sliding 24-hour window.

LCV24HrThreshold

LES15MinThreshold

The threshold for line errored seconds in a 15-minute window or sliding 24-hour window.

LES24HrThreshold

PCV15MinThreshold

The threshold for P-bit coding violations in a 15-minute window or sliding 24-hour window.

PCV24HrThreshold

PES15MinThreshold

The threshold for P-bit errored seconds in a 15-minute window or sliding 24-hour window.

PES24HrThreshold

PSES15MinThreshold

The threshold for P-bit severely errored seconds in a 15-minute window or sliding 24-hour window.

PSES24HrThreshold

SEFS15MinThreshold

The threshold for severely errored framing seconds in a 15-minute window or sliding 24-hour window.

SEFS24HrThreshold

AISS15MinThreshold

The threshold for alarm indication signals in a 15-minute window or sliding 24-hour window.

AISS24HrThreshold

UAS15MinThreshold

The threshold for unavailable seconds in a 15-minute window or sliding 24-hour window.

UAS24HrThreshold

CCV15MinThreshold

The threshold for C-bit coding violations in a 15-minute window or sliding 24-hour window.

CCV24HrThreshold

CES15MinThreshold

The threshold for C-bit errored seconds in a 15-minute window or sliding 24-hour window.

CES24HrThreshold

CSES15MinThreshold

The threshold for C-bit severely errored seconds in a 15-minute window or sliding 24-hour window.

CSES24HrThreshold

Defaults

No default behavior or values. The following defaults apply to new DS3 lines:

RedSeverity: 2

RAISeverity: 1

PerfAlmSeverity: 1

NEAlarmUpCount: 6

NEAlarmDownCount: 1

NEAlarmThreshold: none

LCV15MinThreshold: 14

LCV24HrThreshold: 134

LES15MinThreshold: 12

LES24HrThreshold: 121

PCV15MinThreshold: 10

PCV24HrThreshold: 10

PES15MinThreshold: 10

PES24HrThreshold: 10

PSES15MinThreshold: 10

PSES24HrThreshold: 10

SEFS15MinThreshold: 2

SEFS24HrThreshold: 17

AISS15MinThreshold: 10

AISS24HrThreshold: 10

UAS15MinThreshold: 10

UAS24HrThreshold: 10

CCV15MinThreshold: 10

CCV24HrThreshold: 10

CES15MinThreshold: 10

CES24HrThreshold: 10

SEFS15MinThreshold: 10

CSES24HrThreshold: 10

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card configuration - no functional change

Usage Guidelines

Use this command to change alarm thresholds. For details on threshold counts, refer to Table 6-3.

Examples

The following example changes the dsx3PerfAlmSeverity at DS3 line at slot 7 line 1 to major (2).

chds3alm 7.1 # # 2

Related Commands

Command Description

addds3ln

Add DS3 line

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List DS3 current statistics

lsds3intst

List DS3 interval statistics

lsds3ln

List DS3 line

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

chds3ln

Change DS3 line.

chds3ln Location numOfLines [LineType LineCoding SendCode LoopConfig XmitClkSrc Cable]

Syntax Description

Location

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

numOfLines

Number of lines to change. Values: 1-76.

LineType

The type of DS3 C-bit, which affects the interpretation of the usage and error statistics. Values are 1 - 8 and have the following names:

1=dsx3other (reserved for future use)

2=dsx3SYNTRAN (reserved for future use)

3=dsx3M23

4=dsx3CbitParity (reserved for future use)

5=dsx3ClearChannel (reserved for future use)

6=e3other (reserved for future use)

7=e3Framed (reserved for future use)

8=e3Plcp (reserved for future use)

LineCoding

Zero suppression used on this interface.The line coding dsx3B3ZS and e3HDB3 refers to patterns of normal bits and bipolar violations that are used to replace sequences of zero bits of a specified length. Values are 1 - 3 and have the following names:

1=dsx3Other

2=dsx3B3ZS

3=e3HDB3 (reserved for future use)

SendCode

The type of code being sent across the DS3/E3 interface by the device. (Optional for E3 interfaces.) Values are 1 - 6 and have the following names and meanings:

1=dsx3SendNoCode, sending looped or normal data

2=dsx3SendLineCode, sending a request for a line loopback

3=dsx3SendPayloadCode, sending a request for a payload loopback (all DS1/E1s in a DS3/E3 frame)

4=dsx3SendResetCode, sending a loopback deactivation request

5=dsx3SendDS1LoopCode, requesting loopback for a particular DS1/E1 within a DS3 frame

6=dsx3SendTestPattern, sending a test pattern

LoopConfig

The loopback configuration of the DS3/E3 interface. Values are 1 - 4 and have the following names:

1=dsx3NoLoop

2=dsx3PayloadLoop

3=dsx3LineLoop

4=dsx3OtherLoop

XmitClkSrc

The transmit clock source, which is derived from the recovered receive clock of another DS3 interface. Values are 1-3 and have the following names:

1=loopTiming

2=localTiming

3=throughTiming

Cable

One of the following ranges of lengths for the cable:

1=1 to 225 ft

2=225 to 300 ft

3=300 to 450 ft

4=450 to 900 ft

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card configuration - no functional change

Usage Guidelines

Use this command to configure a DS3 line. If you do not enter optional parameters, no change is made.

Examples

The following command loops line 2 on DMC slot 7:

chds1ln 7.2 # # # # 2

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

che1alm15

Change 15-minute E1 alarm thresholds.

che1alm15 Location [LCV_15 LES_15 UAS_15 FE_ESR_15 FE_SESR_15 FEBE_ESR_15 FEBE_SESR_15 CRC_ESR_15 CRC_SESR_15 ES-ESR_15 SES_ESR_15 ES_15 SES_15 BE_15 PCV_15 CSS_15]

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line

LCV_15

The threshold for LCV (Line Code Violations). A code violation is either a bipolar violation or excessive zeroes event.

LES_15

The threshold for LES (Line Errored Seconds). An errored second is any second with at least one code violation.

UAS_15

The threshold for UAS (Unavailable Seconds). UAS represents the number of seconds that the interface is unavailable in a fixed measurement interval.

FE_ESR_15

The far end threshold for ESR (Errored Seconds Ratio) due to framing errors. ESR is the ratio of errored seconds to total seconds in a fixed measurement interval.

FE_SESR_15

The far end threshold for SESR (Severely Errored Seconds) due to framing errors. SESR is the ratio of severely errored seconds to total seconds in a fixed measurement interval.

FEBE_ESR_15

The far end block error threshold for ESR.

FEBE_SESR_15

The far end block error threshold for SESR.

CRC_ESR_15

The threshold for ESR resulting from CRC errors.

CRC_SESR_15

The threshold for SESR resulting from CRC errors.

ES-ESR_15

The threshold for ESR resulting from ES errors.

SES_ESR_15

The threshold for ESR resulting from SES errors.

ES_15

The threshold for ES (Errored Seconds).

SES_15

The threshold for SES (Severely Errored Seconds).

BE_15

The threshold for BE (Burst Errors)

PCV_15

The threshold for PCV (Path Coding Violations)

CSS_15

The threshold for CSS (Controlled Slip Seconds)

Defaults

No default behavior or values. The following defaults apply to a new E1 line:

LCV_15: 14

LES_15: 12

UAS_15: 10

FE_ESR_15: 800

FE_SESR_15: 20

FEBE_ESR_15: 800

FEBE_SESR_15: 20

CRC_ESR_15: 800

CRC_SESR_15: 20

ES_ESR_15:800

SES_ESR_15: 20

ES_15:35

SES_15: 35

BE_15: 35

PCV_15: 14

CSS_15: 35

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to change the 15-hour thresholds for various error conditions, such as LCV, LES, and LSES. All counter thresholds are integers greater than zero. If you do not enter optional parameters for a threshold, that threshold is not changed.

Examples

The following example changes the threshold for LCV on line 1 of slot 1 from the default values to 150.

che1alm15 1.1 # # # 150

Related Commands

Command Description

addds1ln

Add DS1 line

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

che1alm24

Change E1 alarm thresholds

delds1ln

Delete DS1 line

lse1alm

List E1 alarm thresholds

lse1curst

List E1 line current statistics

lse1cursts

List E1 current statistics

lse1intst

List E1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lse1lnst

List E1 line statistics

lse1totst

List E1 line total statistics

lse1totsts

List E1 total statistics

lslns

List existing lines

che1alm24

Change 24-hour E1 alarm thresholds.

che1alm24 Location [LCV_24 LES_24 UAS_24 FE_ESR_24 FE_SESR_24 FEBE_ESR_24 FEBE_SESR_24 CRC_ESR_24 CRC_SESR_24 ES-ESR_24 SES_ESR_24 ES_24 SES_24 BE_24 PCV_24 CSS_24]

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line

LCV_24

The threshold for LCV (Line Code Violations). A code violation is either a bipolar violation or excessive zeroes event.

LES_24

The threshold for LES (Line Errored Seconds). An errored second is any second with at least one code violation.

UAS_24

The threshold for UAS (Unavailable Seconds). UAS represents the number of seconds that the interface is unavailable in a fixed measurement interval.

FE_ESR_24

The far end threshold for ESR (Errored Seconds Ratio) due to framing errors. ESR is the ratio of errored seconds to total seconds in a fixed measurement interval.

FE_SESR_24

The far end threshold for SESR (Severely Errored Seconds) due to framing errors. SESR is the ratio of severely errored seconds to total seconds in a fixed measurement interval.

FEBE_ESR_24

The far end block error threshold for ESR.

FEBE_SESR_24

The far end block error threshold for SESR.

CRC_ESR_24

The threshold for ESR resulting from CRC errors.

CRC_SESR_24

The threshold for SESR resulting from CRC errors.

ES-ESR_24

The threshold for ESR resulting from ES errors.

SES_ESR_24

The threshold for ESR resulting from SES errors.

ES_24

The threshold for ES (Errored Seconds).

SES_24

The threshold for SES (Severely Errored Seconds).

BE_24

The threshold for BE (Burst Errors)

PCV_24

The threshold for PCV (Path Coding Violations)

CSS_24

The threshold for CSS (Controlled Slip Seconds)

Defaults

No default behavior or values. The following defaults apply to a new E1 line:

LCV_24: 134

LES_24: 121

UAS_24: 10

FE_ESR_24: 800

FE_SESR_24: 20

FEBE_ESR_24: 800

FEBE_SESR_24: 20

CRC_ESR_24: 800

CRC_SESR_24: 20

ES_ESR_24:800

SES_ESR_24: 20

ES_24: 15: 50

SES_24: 50

BE_24: 50

PCV_24: 50

CSS_24: 50

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to change the 24-hour thresholds for various error conditions, such as LCV, LES, and LSES. All counter thresholds are integers greater than zero. If you do not enter optional parameters for a threshold, that threshold is not changed.

Examples

The following example changes the threshold for LCV on line 1 of slot 1 from the default values to 150.

che1alm24 1.1 # # # 150

Related Commands

Command Description

addds1ln

Add DS1 line

chds1ln

Change DS1 line

che1alm15

Change E1 alarm thresholds

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lse1alm

List E1 alarm thresholds

lse1curst

List E1 line current statistics

lse1cursts

List E1 current statistics

lse1intst

List E1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lse1lnst

List E1 line statistics

lse1totst

List E1 line total statistics

lse1totsts

List E1 total statistics

lslns

List existing lines

che1almsev

Change E1 alarm severity.

che1almsev Location [Red_Severity RAI_Severity RMAI_Severity TS16_Severity Perf_Alarm_Severity ]

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line

Red_Severity

The near end LOF indication, either minor or major. Values: 1 or 2, respectively.

RAI_Severity

The remote alarm indication, either minor or major. Values: 1 or 2, respectively.

RMAI_Severity

The RMAI alarm indication, either minor or major. Values: 1 or 2, respectively.

TS16_Severity

The TS16 alarm indication, either minor or major. Values: 1 or 2, respectively.

Perf_Alarm_Severity

The performance alarm indication, either minor or major. The performance alarm is set if any of the thresholds is exceeded. Values: 1 or 2, respectively.

Defaults

No default behavior or values. The following defaults apply to a new DS1 line:

Red_Severity: 2

RAI_Severity: 1

RMAI_Severity: 1

TS16_Severity: 1

Perf_Alarm_Severity: 1

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to change the alarm severity indication for various alarm conditions, such as red alarm and performance alarm. If you do not enter optional parameters for a threshold, that threshold is not changed.

Examples

The following example changes the red alarm severity on line 1 of slot 1 from the default value to minor.

che1almsev 1.1 1

Related Commands

Command Description

addds1ln

Add DS1 line

chds1ln

Change DS1 line

che1alm15

Change 15-minute E1 alarm thresholds

che1alm24

Change 24-hour E1 alarm thresholds

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lse1alm

List E1 alarm thresholds

lse1curst

List E1 line current statistics

lse1cursts

List E1 current statistics

lse1intst

List E1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lse1lnst

List E1 line statistics

lse1totst

List E1 line total statistics

lse1totsts

List E1 total statistics

lslns

List existing lines

chem

Configure email registration.

chem [EmailServerDomain EmailServerIPAddr SourceEmailAddr]

Syntax Description

EmailServerDomain

The domain name of the email server on your network. Values: A text string, maximum 30 characters.

EmailServerIPAddr

The IP address of the email server in standard IP dot notation. The 0.0.0.0 setting disables email notifications. Any valid IP address enables email notifications.

SourceEmailAddr

The 'from' email address for messages from the MGX 8260 Media Gateway. Values: A text string, maximum 40 characters. For example, node1@cisco.com.

Defaults

EmailServerIPAddr: 0.0.0.0

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure email server information and the source email address for receiving alerts about SNMP traps. You must configure the email server IP address correctly enable email alerts. If one or more fields of the IP address exceeds 255, SNMP stores the address as 255.255.255.255 and the MGX 8260 Media Gateway disables email alerts.

Examples

The following example configures email from server domain WORKGROUP and server IP address 10.10.1.10 with a 'from' email address of finance2@bank.com.

chem WORKGROUP 10.10.1.10 finance2@bank.com

Related Commands

Command Description

addereg

Add email registration

chereg

Change email registration

delereg

Delete email registration

lsem

List email server

lsereg

List entry registered

lseregs

List registered email alerts

chereg

Change email registration.

chereg Index EmailAddress Trap#1 [Trap#2 ... Trap#20]

Syntax Description

Index

Position of the email address in the SnmpEmailRegTable. Values: integer, 1-10.

EmailAddress

The email address, up to 40 characters, of the person who wants to receive email about traps.

Trap#n

One to twenty existing trap numbers.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to change email registration on as many as 20 traps, the maximum that are monitored. You change an email registration entry in the same manner as you add an email registration entry.

Examples

The following example changes the email address at index 52 to johnt@hal to receive alerts when events are raised by traps 1 and 2.

chereg 9 johnt@hal 1000 1001

Related Commands

Command Description

addereg

Add email registration

chem

Configure email registration

delereg

Delete email registration

lsem

List email server

lsereg

List entry registered

lseregs

List registered email alerts

chethln

Change Fast Ethernet line.

chethln Location [Gway_Addr RDP Mask Mode]

Syntax Description

Location

The slot and line number, delimited by a period, of the Ethernet line. Values: Slot = 9, Line = 1-4.

Gway_Addr

The IP address of the primary gateway for the interface.

RDP

The state of the Router Discovery Protocol. Values: 1 = disabled,
2 = enabled.

Mask

The subnet mask in dotted notation a.b.c.d.

Mode

The duplex mode of the line. Values: 1 = Half duplex, 2 = Full duplex.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to change an Ethernet interface on the Fast Ethernet SCC and back card.

Examples

Tor example, the following command enables RDP but leaves other parameters unchanged on Fast Ethernet line 1 in slot 9:

chethln 9.1 # 2

Related Commands

Command Description

addethln

Add Ethernet line

delethln

Delete Ethernet line

upethln

Activate Ethernet line

dnethln

DeActivate Ethernet line

lsethln

List Ethernet line

lsethlns

List Ethernet Lines

chgw

Specify a gateway router.

chgw Address

Syntax Description

Address

An IP address in dotted notation w.x.y.z

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the gateway IP address for management traffic. The system uses this gateway to route management traffic outside the local subnet.

Examples

The following example configures the gateway IP address.

chgw 10.2.2.1

Related Commands

Command Description

chsysip1

Change system IP1 address

chsysip2

Change system IP2 address

lsmgips

List management IP addresses

chibip

Configure in-band IP.

chibip Address Mask

Syntax Description

Address

An IP address in dotted notation w.x.y.z

Mask

A subnet mask in dotted notation a.b.c.d

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the IP address and mask of the in-band system management interface. Do not set the in-band IP address to 0.0.0.0.

Examples

The following example configures the IP address, mask, and gateway of the in-band system management interface.

chibip 10.2.2.5 255.255.255.0

Related Commands

Command Description

chsysip1

Change system IP1 address

chsysip2

Change system IP2 address

lsmgips

List management IP addresses

chidletm

Change idle time before session termination.

chidletm idleTime

Syntax Description

idleTime

The idle time in minutes. Values: 0 - 2147483647. 0 = infinity.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to change the amount of time allowed for no keyboard input. When the time expires, the session terminates.

Examples

The following example changes the idle time to 15 minutes.

chidletm 15

chipdccot

Change IPDC COTs.

chipdccot rcot tcot

Syntax Description

rcot

IPDC COT receive tone. Values: co1 (2010 Hz) or co2 (1780 Hz)

tcot

IPDC COT transmit tone. Values: 1 = co1; 2 = co2

Defaults

rcot: 1

tcot: 2

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure IPDC COTs. For the transponder COT, when the media gateway controller does not supply the tones, the default tone the gateway should receive the default COT receive tone and transmit the default COT transmit tone.

Examples

The following example configures the IPDC COT to receive co2 and transmit co1.

chipdccot 2 1

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

chds1lnecho

Configure DS1 line echo cancelling

chipdcgwip

Change IPDC gateway IP and TCP port.

chipdcgwip ip port

Syntax Description

ip

The IP address of gateway for MSCP link.

port

The TCP Port number of gateway for MSCP link. This port number cannot be a well-known port number. Values: 1025 - 65535. Default: 5000

Defaults

port: 5000

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure.When you modify the gateway IP address, you must also change the related TCP port number.

Examples

The following example configures the Soft Switch gateway IP address and TCP port.

chipdcgwip 1025 6000

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcmaxm

Change IPDC maximum modules.

chipdcmaxm num

Syntax Description

num

Maximum number of modules (slot cards) supported. Values: integer from 1 - 16

Defaults

num: 16

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to set the maximum number of modules.

Examples

The following example sets the maximum number of modules to 10.

chipdcmaxm 10

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcpssip

Change IP Device Control (IPDC) primary Soft Switch IP and TCP port.

chipdcpssip ip port

Syntax Description

ip

The primary Soft Switch IP address.

port

The primary Soft Switch TCP Port. This port number cannot be a well-known port number. Values: 1025 - 65535. Default: 5000

Defaults

port: 5000

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the primary Soft Switch IPDC. If you the primary Soft Switch IP Address, change the related, primary TCP port also.

Examples

The following example configures the primary Soft Switch IP address and TCP port.

chipdcpssip 10.1.1.1 1026

Related Commands

Command Description

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcssadm

Change IPDC administrative status.

chipdcssadm primary secondary downtime

Syntax Description

primary

The administrative status of link with the primary Soft Switch. Values:

1=down, disconnect the current call server

2=up, connect the current call server

3=graceful disconnect, disconnect the current call server after the time specified by downtime. (reserved for future use)

secondary

The administrative status of link with the secondary Soft Switch. Values:

1=down, disconnect the current call server

2=up, connect the current call server

3=graceful disconnect, disconnect the current call server after the time specified by downtime. (reserved for future use)

downtime

The graceful disconnect time for both Soft Switches. Value: 0 only (no graceful disconnect)

Defaults

primary: 1

secondary: 1

downtime: 0

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to connect or disconnect the primary or secondary IPDC administrative status. If the downtime is set to 0, the link is disconnected immediately. If the downtime is set to greater than 0, the Soft Switch disconnects in the time specified.

Examples

The following example sets the administrative status of the primary IPDC Soft Switch down.

chipdcssadm 1

chipdcssbaynum

Change IPDC bay number.

chipdcssbaynum num

Syntax Description

num

The number associated with gateway being controlled. A string of exactly 8 characters.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to assign a bay number to the IPDC.

Examples

The following example configures the bay number.

chipdcssbaynum NUM45678

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcsshlth

Change IPDC health check.

chipdcsshlth admp adms dntime

Syntax Description

admp

Enable or disable the link health check for the primary Soft Switch.Values: 1=enable; 2=disable

adms

Enable or disable the link health check for the secondary Soft Switch. Values: 1=enable; 2=disable

dntime

The time to wait before disabling the link health check. Values: 400 to 10000 msec

Defaults

admp: 1

adms: 1

dntime: 1000

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to enable the primary or secondary link health check.

Examples

The following example enables the primary link health check in 200 msec.

chipdcsshlth 1 200

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcssid

Change IPDC system Id.

chipdcssid ID

Syntax Description

ID

Identifier of the gateway being controlled by IPDC protocol, a string from 0 to 24 characters.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the IPDC system identifier.

Examples

The following example configures the IPDC system Id to 15.

chipdcssid 15

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcssnumfor

Change IPDC numbering format.

chipdcssnumfor format

Syntax Description

format

The format that determines the Soft Switch interpretation of module, line, and channel numbers on an MGX 8260. Values: 1= 0-base; 2=1-base.

Defaults

format: 1

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to set the IPDC numbering format.

Examples

The following example sets the IPDC numbering format to 1-base.

chipdcssnumfor 2

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port.

chipdcsssip ip port

Syntax Description

ip

The secondary Soft Switch IP address.

port

The secondary Soft Switch TCP port. This port number cannot be a well-known port number. Values: 1025 - 65535. Default: 5000

Defaults

port: 5000

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the secondary Soft Switch IPDC. If you change the secondary Soft Switch IP Address, change the corresponding secondary TCP port also.

Examples

The following example configures the secondary Soft Switch IP address and TCP port.

chipdcsssip 10.1.1.1 1026

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdcsstype

Change IPDC system type.

chipdcsstype type

Syntax Description

type

The string of exactly 9 characters that identifies the manufacturer and model of the MGX 8260 Media Gateway.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the IPDC system type.

Examples

The following example changes the IPDC system type to ID3456789.

chipdcsstype ID34565789

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chipdctimer

Change IPDC timers and retry counters.

chipdctimer ssConnRetryTimer ssConnRetryThr tcpConnRetrTimer nsupRtxTimer lnkActiveTimer maxTcpConnRetry maxNsupRetry

Syntax Description

ssConnRetryTimer

Minimum connection retry interval for primary or secondary Soft Switch when the link is up. The connection interval doubles with every retry attempt until the ssConnRetryThr value is reached. Values: integer 2000 to15000 msec.

ssConnRetryThr

Maximum Soft Switch connection retry interval. Values: integer 16000 to 256000 msec

tcpConnRetrTimer

Retry interval for a TCP connection when the link is down. Values: 1000 to 10000 msec

nsupRtxTimer

Retry interval for NSUP message. The timer stops after receipt of ASUP. Values: 1000 to 10000 msec

lnkActiveTimer

The time this device waits for a message from the Soft Switch before declaring the link down. If the health check is enabled, the link stays up until the heartbeat times out. Values: 1000 to 60000 msec

maxTcpConnRetry

The maximum number of TCP connection attempts when the link is down. Values 0 to 10

maxNsupRetry

The maximum NSUP retransmission attempts when the link is down. Values: 0 to 10

Defaults

ssConnRetryTimer: 4000

ssConnRetryThr: 64000

tcpConnRetryTimer: 2000

nsupRetrTimer: 2000

lnkActiveTimer: 60000

maxTcpConnRetry: 1

maxNsupRetry: 2

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the IPDC timers and retry counters.

Examples

The following example sets the IPDC time to a minimum value of 5000 and a.maximum of 20000.

chipdctimer 5000 20000 1500

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chkey

Change file key.

chkey key

Syntax Description

key

Up to 6 alphanumeric characters

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the tftp security key for uploading and downloading files to prevent unauthorized file transfers.

Examples

The following example changes the security key to 323bf.

chkey e23bf

Related Commands

Command Description

addusp

Add user profile

chpwd

Change user password

delusp

Delete user profile

chm13

Change DS1 to DS3 map.

chm13 SrcDS3LineNum SrcDS1LineNum DestDS1SlotNum DestDS1LineNum

Syntax Description

SrcDS3LineNum

The number of the source DS3 line. Values: 1 - 6.

SrcDS1LineNum

The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28.

DestDS1SlotNum

The logical slot number for the destination NSC (Narrowband Service Card).

DestDS1LineNum

The number of the DS1, or starting DS1, in the NSC. Valid entries are 1 through 16.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to change a DS3 to DS1 mapping from Distribution Matrix Card (DMC) to the NSC.

Examples

For example the following command sequence adds three map table entries and then changes one of them:

addm13 1 3 1 1 3 chm13 1 3 1 4

Related Commands

Command Description

addm13

Add map to DS1 from DS3

delm13

Delete DS1 to DS3 map

lsm13

List DS3-to-DS1 mapping

lsm13s

List DS3-to-DS1 mappings

chmgcpcore

Change MGCP core parameters.

chmgcpcore RequestTimeOut RequestRetries AdminStatus RestartInProgMWD RestartDelay ResponseTimeout ConnectivityTimeout

Syntax Description

RequestTimeOut

The time in milliseconds before retransmitting an unacknowledged message. Values: 1 - 100000.

RequestRetries

The maximum number of retries for a request that times out. Values: 0 - 15.

AdminStatus

The desired state of the protocol.

1=up—bring up protocol administratively

2=down—bring down protocol administratively

3=gracefulDown—gracefully shut down protocol

RestartInProgMWD

The maximum waiting delay, in milliseconds, before the Media Gateway interface sends the Restart In Progress message to the Media Gateway Controller. Values: 0 - 600000

RestartDelay

The delay before a graceful shutdown. Values: 0 to 600. 0 = immediate timeout, meaning shutdown.

ResponseTimeout

The time in milliseconds to wait before retransmitting unacknowledged messages. Values: 1-100,000

ConnectivityTimeout

The time in milliseconds to wait for a request from MGCP before dropping the link. Values: 1-100,000

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the core parameters for the MGCP protocol stack. It is the responsibility of the MGX 8260 Media Gateway to provide suitable timeouts for all outstanding commands, and to retry commands when timeouts occur. Setting the restart timer before sending the Restart In Progress notification to the media gateway controller avoids network congestion during the critical period of service restoration.

Examples

The following example sets MGCP core parameters.

chmgcpcore 600 2 2 500 -1 500 500

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

lsmgcpstat

List MGCP statistics

chmgcpdname

Change the node domain name.

chmgcpdname DomainName

Syntax Description

DomainName

The domain name for this node. Value: 1-64 characters

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to define a domain name for the MGX 8260 chassis. The domain name is an alternative to IP addressing.

Examples

The following assigns a domain name.

chmgcpdname cisco

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chmgcpcore

Change MGCP core parameters

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

chmgcplocaladdr1

Change the local MGCP address for network 1.

chmgcplocaladdr1 MgcpLocalAddressNet1 MgcpLocalPrimUDPPortNet1

Syntax Description

MgcpLocalAddressNet1

The IP address of the Media Gateway interface for network 1. Specify the IP address in standard dot notation. Values: string.

MgcpLocalPrimUDPPortNet1

The primary UDP port of the Media Gateway interface for network 1. Values: 1025..65535.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The MgcpLocalAddressNet1 parameter specifies the address of the default Media Gateway Controller to which the RSIP (RestartInProgress) message is sent whenever system starts up or line goes up. If the DNS name is entered and the IP address is found, Media Gateway sends RSIP to the desired MGC. If no IP address is found or no such DNS name exists, no RSIP is sent. If the IP address is entered, Media Gateway sends RSIP to that address. Possible reasons for no response are the network is down or the user misconfigured either the IP address, domain name or UDP port number.

The UDP port is used with MgcpLocalAddressNet1 to specify the local address of the Media Gateway.

Examples

The following example changes the local MGCP address for network 1.

chmgcplocaladdr1 10.1.1.1 2000

Related Commands

Command Description

chmgcplocaladdr2

Change the MGCP local address for network 2

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

chmgcpcore

Change the primary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

lsmgcpstat

List MGCP statistics

chmgcplocaladdr2

Change the MGCP local address for network 2.

chmgcplocaladdr2 MgcpLocalAddressNet2 MgcpLocalPrimUDPPortNet2

Syntax Description

MgcpLocalAddressNet2

The IP address of the Media Gateway interface for network 2. Specify the IP address in standard dot notation.

MgcpLocalPrimUDPPortNet2

The primary UDP port of the Media Gateway interface for network 2. Values: 1025..65535.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The MgcpLocalAddressNet parameter specifies the address of the default Media Gateway Controller to which the RSIP (RestartInProgress) message is sent whenever system starts up or line goes up. If the DNS name is entered and the IP address is found, Media Gateway sends RSIP to the desired MGC. If no IP address is found or no such DNS name exists, no RSIP is sent. If the IP address is entered, Media Gateway sends RSIP to that address. Possible reasons for no response are the network is down or the user misconfigured either the IP address, domain name or UDP port number.

The UDP port is used with MgcpLocalAddressNet parameter to specify the local address of the Media Gateway.

Examples

The following example changes the MGCP local address for network 2.

chmgcplocaladdr2 10.10.1.1 2000

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

chmgcpcore

Change the primary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

lsmgcpstat

List MGCP statistics

chmpc

Configure default MPC parameters.

chmpc DefTypeNetwork DefPktnPeriod DefBandwidth DefEchoCancel DefSilenceSupp DefTypeOfService DefResourceRes DefCOTReceiveTone DefCOTTransmitTone Encoding

Syntax Description

DefTypeNetwork

The type of network.

1=voIp

2=voAtm

3=local

DefPktnPeriod

Packetization period in milliseconds. Value: fixed at 10

DefBandwidth

The network bandwidth in kbps. Values: 8 and 64 kbps

DefEchoCancel

Enables or disables echo cancellation.

1=off

2=on

DefSilenceSupp

Enables or disables silence suppression.

1=off

2=on

DefTypeOfService

The type of Service. Values: 1-256, where 1 indicates no service type

DefResourceRes

The resource reservation type.

1=bestEffort

2=guaranteed

3=notUsed

4=controlledLoad

DefCOTReceiveTone

The default receive tone. For transponder COT, when the media gateway controller does not supply the tones, the default tone the gateway receives is the default COT receive tone.

1=co1 (2010 Hz)

2=co2 (1780 Hz)

DefCOTTransmitTone

The default transmit tone. For transponder COT, when the media gateway controller does not supply the tones, the default tone the gateway transmits is the default COT transmit tone.

1=co1

2=co2

Encoding

The type of voice encoding when not specified by the MGC:

1=PCMA—A-law encoding

2=PCMU—Mu-law encoding

3=G729A

4=G72632K

Defaults

DefTypeNetwork: 3

DefPktnPeriod: 10

DefBandwidth: 64

DefEchoCancel: 1

DefSilenceSupp: 1

DefTypeOfService: 2

DefResourceRes: 1

DefCOTReceiveTone: 1

DefCOTTransmitTone: 2

Command Modes

Security level 2

Command History

Release Modification

1.1

This command was first introduced.

Usage Guidelines

Use this command to configure default MPC parameters.

Examples

The following sets the network type to local.

chmpc 3

Related Commands

Command Description

lsmpc

List MPC information.

chndinf

Configure node information.

chndinf RackNum NodeName NodeNum

Syntax Description

RackNum

Shelf number for node. Values: 1 - 100.

NodeName

Alphanumeric identifier for node. Values: up to 15 characters

NodeNum

Numeric identifier for node. Values: Integer, 1 - 1000

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure system identification information and set the DS1 line type. You set the number of the physical rack, along with the name and number of the chassis. The rack contains the shelf, or chassis, for a node.

Examples

The following example configures node information.

chndinf 3 Floor3 12

Related Commands

Command Description

chsyslnmd

Change the line mode for the chassis.

lsndinf

List node information.

chpclksrc

Change primary clock source.

chpclksrc SlotNum LineNum ClkSrcType CardType

Syntax Description

SlotNum

Slot number of the clock source. Values: 1 to 16

LineNum

Line number of clock source. Values:

NSC DS1 lines: 1 to 16

BSC DS3 lines: 501 to 506

DMC DS3 lines: 1 to 6

SCC, OC3 type: 1 to 4

SCC, BITS type: 1

ClkSrcType

Type of clock source, broadband, narrowband, external, or internal. Values: 1, 2, 3, and 4 respectively.

CardType

Type of card, bits or OC3. Values 1 and 2, respectively.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

1.1

Added BSC extensions

1.2

Added OC-3 extensions

Usage Guidelines

Use this command to configure the primary clock source. If the Type parameter is broadband or narrowband, the Slot Num and Line Num parameters are mandatory. If the Type is external or internal, do not provide this parameter.

Examples

The first example configures an external clock source. The second configures a broadband clock source on slot 12, line 8.

chpclksrc # # 3 # chpclksrc 12 8 1 #

Related Commands

Command Description

chsclksrc

Change secondary clock source

swclk

Switch clock

lsclksrcs

List all clock sources

chpcs

Configure primary control server.

chpcs Address Interface Check

Syntax Description

Address

Primary MCS address in dotted notation w.x.y.z.

Interface

Default tcp port number for primary MCS. Values: Integer > 1024.

Check

Enables or disables the MSCP health check. Values: 1 = enabled, 2 = disabled

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the IP address and interface of the primary MCS.

Examples

The following example configures the primary CS.

chpcs 10.10.10.1 5003 1

chpmgcpaddr

Change the primary Media Gateway Controller addresses.

chpmgcpaddr MgcpPMGCAddressNet1 MgcpPMGCCfgUDPPortNet1 MgcpPMGCAddressNet2 MgcpPMGCCfgUDPPortNet2

Syntax Description

MgcpPMGCAddressNet1

The IP address of the Primary Media Gateway Controller on network 1. Specify the IP address in standard dot notation. Values: string.

MgcpPMGCCfgUDPPortNet1

The UDP port of the Media Gateway Controller on network 2. Values: 1025..65535.

MgcpPMGCAddressNet2

The IP address of the Primary Media Gateway Controller on network 2. Specify the IP address in standard dot notation. Values: string.

MgcpPMGCCfgUDPPortNet2

The secondary UDP port of the Media Gateway Controller on network 2. Values: 1025..65535.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The MgcpMGCCfgaddress parameter specifies the address of the default Media Gateway Controller to which the RSIP (RestartInProgress) message is sent whenever system starts up or line goes up. If the DNS name is entered and the IP address is found, Media Gateway sends RSIP to the desired MGC. If no IP address is found or no such DNS name exists, no RSIP is sent. If the IP address is entered, Media Gateway sends RSIP to that address. Possible reasons for no response are the network is down or the user misconfigured either the IP address, domain name or UDP port number.

The UDP port is used with MgcpPMGCAddress to specify the local address of the Media Gateway.

Examples

The following example sets the primary MGCP controller addresses for a redundant network configuration.

chpmgcpaddr 10.1.1.1 2000 10.10.1.1 2000

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

lsmgcpstat

List MGCP statistics

chprotocol

Switch between MGCP and IPDC protocols.

chprotocol protocol

Syntax Description

protocol

The call control protocol. Values: 1 = MGCP; 2 = IPDC

Defaults

protocol: 1

Command Modes

Security level 2

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

The MGX 8260 Media Gateway supports two protocols for voice call control, MGCP and IPDC. Use this command to switch from one protocol to the other. This command automatically resets the chassis.

Examples

The following example switches from MGCP to IPDC.

chprotocol 2

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chpseudoip

Change pseudo IP address for IPDC.

chpseudoip [pseip]

Syntax Description

pseip

This IP address that is used to change IP address for IPDC.

Defaults

No default behavior or values.

Command Modes

Security level

Command History

Release Modification

1.1

This command was first introduced.

Usage Guidelines

Use this command to configure a pseudo IP address that represents the four broadband ports. This IP address simplifies call control because the Soft Switch can reference one IP address rather than four. The MGX 8260 Media Gateway balances the load among the broadband interfaces. This pseudo address must be on the same subnet as the broadband ports.

Examples

The following example sets the pseudo IP address at 10.1.1.1.

chpseudoip 10.1.1.1

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

chpwd

Change password.

chpwd

Syntax Description

This command has no arguments or keywords.

Command Modes

Security level 1-6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this interactive command to change the password of an existing account. To use this command, you must first log onto the account you want to change. Generally, users change their own passwords with this command.

Examples

The following example shows the interactive session for a password change:

MGX.9.ACTIVE-> chpwd Rules: 1. Password length must be 4 - 10 2. First character must be alphanumeric 3. Only printable characters are allowed 4. Space not allowed Enter Password : ***** New Password : ******** Verify Password: ********

chqprf

Change queue profile.

chqprf Card Queue#

Syntax Description

Card

The number of an SCC card.

Queue#

The ATM queue profile number. Values: 1 - 10.

Defaults

Queue#: 1

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Specifies the ATM traffic queue profile for an entire SCC card. The MGX 8260 defines 10 profiles for different traffic types. Profile 1 is recommended.

Examples

The following example changes the profile of card 9 to give it an ATM queue profile of 2.

chqprf 9 2

chsclksrc

Change secondary clock source.

chsclksrc Slot Line ClkSrcType CardType

Syntax Description

Slot

Slot number of the clock source.

Line

Line number of clock source.

Type

Type of clock source, broadband, narrowband, external, or internal. Values: 1, 2, 3, and 4 respectively.

CardType

Type of card, bits or OC3. Values 1 and 2, respectively.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the secondary clock source. If the Type parameter is broadband or narrowband, the Slot Num and Line Num parameters are mandatory. If the Type is external or internal, do not provide this parameter.

Examples

The first example configures a external bits clock source. The second configures a broadband clock source on slot 1, line 2.

chsclksrc # # 3 1 chsclksrc 1 2 1 2

Related Commands

Command Description

chpclksrc

Change primary clock source

swclk

Switch clock

lsclksrcs

List clock sources

chscs

Change secondary control server (reserved for future use).

chscs Address Interface Check

Syntax Description

Address

Secondary MCS IP address in dotted notation w.x.y.z

Interface

Secondary tcp port number for sending IP packets to the secondary MCS

Check

Enables or disables the MSCP health check. Values: 1 = enabled, 2 = disabled

Defaults

No default values or behavior.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the IP address and interface for the secondary MCS.

Examples

The following examples configures a secondary control server at 10.10.10.1 for a PPP interface.

chscs 10.10.10.1 3 5004 2

chsmgcpaddr

Change the secondary Media Gateway Controller addresses.

chsmgcpaddr MgcpSMGCAddressNet1 MgcpSMGCCfgUDPPortNet1 MgcpSMGCAddressNet2 MgcpSMGCCfgUDPPortNet2

Syntax Description

MgcpSMGCAddressNet1

The IP address of the Secondary Media Gateway Controller on network 1. Specify the IP address in standard dot notation. Values: string.

MgcpSMGCCfgUDPPortNet1

The UDP port of the Media Gateway Controller on network 1. Values: 1025..65535.

MgcpSMGCAddressNet2

The IP address of the Secondary Media Gateway Controller on network 2. Specify the IP address in standard dot notation. Values: string.

MgcpSMGCCfgUDPPortNet2

The UDP port of the Media Gateway Controller on network 2. Values: 1025..65535.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The MgcpSMGCAddressNet parameter specifies the address of the default Media Gateway Controller to which the RSIP (RestartInProgress) message is sent whenever system starts up or line goes up. If the DNS name is entered and the IP address is found, Media Gateway sends RSIP to the desired MGC. If no IP address is found or no such DNS name exists, no RSIP is sent. If the IP address is entered, Media Gateway sends RSIP to that address. Possible reasons for no response are the network is down or the user misconfigured either the IP address, domain name or UDP port number.

The UDP port is used with MgcpSMGCAddressNet to specify the local address of the Media Gateway.

Examples

The following example sets the primary MGCP controller addresses for a redundant network configuration.

chsmgcpaddr 10.1.1.3 2000 10.10.1.4 2000

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chpmgcpaddr

Change the primary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

lsmgcpstat

List MGCP statistics

chsonetalm

Change SONET alarm thresholds.

chsonetalm Location [redSeverity yellow Severity perfSeverity SeCV15MinThresh SeCV24HrThresh SeES15MinThresh SeES24HrThresh SeSES15MinThresh SeSES24HrThresh SeSEFS15MinThresh SeSEFS24HrThresh LCV15MinThresh LCV24HrThresh LES15MinThresh LES24HrThresh LSES15MinThresh LSES24HrThresh LUAS15MinThresh LUAS24HrThresh PCV15MinThresh PCV24HrThresh PES15MinThresh PES24HrThresh PSES15MinThresh PSES24HrThresh PUAS15MinThresh PUAS24HrThresh

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

redSeverity

The red alarm severity:

1=Minor (reserved for future use)

2=Major

yellowSeverity

The yellow alarm severity:

1=Minor

2=Major (reserved for future use)

perfSeverity

The performance alarm severity:

1=Minor

2=Major (reserved for future use)

SeCV15MinThresh

The section threshold for code violations in a 15-minute or sliding 24-hour window. Code violations are Bit Interleaved Parity errors detected in the incoming signal.

SeCV24HrThresh

SeES15MinThresh

The section threshold for errored seconds in a 15-minute or sliding 24-hour window. An errored second is a second with one or more code violations at that layer or incoming defects.

SeES24HrThresh

SeSES15MinThresh

The section threshold for severely errored seconds in a 15-minute or sliding 24-hour window. A severely errored second is one in which code violations or incoming defects occurred.

SeSES24HrThresh

SeSEFS15MinThresh

The section threshold for severely errored frame seconds in a 15-minute or sliding 24-hour window. A SEFS is a second containing one or more SEF events.

SeSEFS24HrThresh

LCV15MinThresh

The line threshold for code violations in a 15-minute or sliding 24-hour window. Code violations are Bit Interleaved Parity errors detected in the incoming signal.

LCV24HrThresh

LES15MinThresh

The line threshold for errored seconds in a 15-minute or sliding 24-hour window. An errored second is a second with one or more code violations at that layer or incoming defects.

LES24HrThresh

LSES15MinThresh

The line threshold for severely errored seconds in a 15-minute or sliding 24-hour window. A severely errored second is one in which code violations or incoming defects occurred.

LSES24HrThresh

LUAS15MinThresh

The line threshold for unavailable seconds in a 15-minute or sliding 24-hour window. Unavailable seconds represent the number of seconds that the interface is unavailable.

LUAS24HrThresh

PCV15MinThresh

The path threshold for code violations in a 15-minute or sliding 24-hour window. Code violations are Bit Interleaved Parity errors detected in the incoming signal.

PCV24HrThresh

PES15MinThresh

The path threshold for errored seconds in a 15-minute or sliding 24-hour window. An errored second is a second with one or more code violations at that layer or incoming defects.

PES24HrThresh

PSES15MinThresh

The path threshold for severely errored seconds in a 15-minute or sliding 24-hour window. A severely errored second is one in which code violations or incoming defects occurred.

PSES24HrThresh

PUAS15MinThresh

The path threshold for unavailable seconds in a 15-minute or sliding 24-hour window. Unavailable seconds represent the number of seconds that the interface is unavailable.

PUAS24HrThresh

]


Defaults

This command has no default behavior or values. The following defaults apply to a new SONET line:

redSeverity: 2

yellowSeverity: 1

perfSeverity: 1

SeCV15MinThresh: 15

SeCV24HrThresh: 134

SeES15MinThresh: 12

SeES24HrThresh: 120

SeSES15MinThresh: 10

SeSES24HrThresh: 100

SeSEFS15MinThresh: 5

SeSEFS24HrThresh: 20

LCV15MinThresh: 15

LCV24HrThresh: 134

LES15MinThresh: 12

LES24HrThresh: 120

LSES15MinThresh: 10

LSES24HrThresh: 100

LUAS15MinThresh: 12

LUAS24HrThresh: 20

PCV15MinThresh: 15

PCV24HrThresh: 134

PES15MinThresh: 12

PES24HrThresh: 120

PSES15MinThresh: 10

PSES24HrThresh: 100

PUAS15MinThresh: 12

PUAS24HrThresh: 120

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to enable and configure alarm thresholds for SONET lines. When a counter exceeds a threshold, the system raises the performance alarm.

Examples

The following example changes the threshold for code violations in a 15-minute window:

chsonetalm 9.1 # # # 30

Related Commands

Command Description

chsonetperdi

Change SONET E-RDI parameters

chsonettrace

Change SONET trace parameters

chsonetexptrace

Change SONET expected trace parameters

lssonetlnerdi

List E-RDI information for a SONET line

lssonetlnerdis

List summary E-RDI information for all SONET lines

chsonetexptrace

Change expected path trace parameters for SONET lines.

chsonetexptrace Location [numOfLines expTraceIdLen expTraceId expTraceIdPosition]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

numOfLines

The number of lines to add. Values: 1-4.

expTraceIdLen

The expected trace identifier length for the SONET path:

16=message contains 16 bytes (SDH only)

64=message contains 64 bytes (SONET or SDH)

expTraceId

The expected trace identifier in the SONET path overhead. Value: ASCII string of either 16 or 62 characters, depending on the TraceIdLen setting. You specify the ASCII characters as pairs of hexidecimal characters. For example, a you express a space as 20.

Note 1: The 16 byte message normally alters one byte for synchronization, as defined by TraceIdPosition.

Note 2: The 64 byte message uses the last two bytes for synchronization, so the maximum trace identifier length is 62 ASCII characters. Only printable ASCII characters are allowed.

expTraceIdPosition

The position within a 16-byte message of the synchronization byte. The most significant bit of this byte is set high. Values: 1-16.

Alternatively, this parameter defines the following special cases:

0=No bit set

17=All most significant bits set low

Defaults

numOfLines: 1

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the path trace parameters for SONET lines. This command works in conjunction with the chsonettrace and chsonetperdi commands to configure a SONET line test.

Examples

The following example defines an expected trace identifier of hello world in a 64-byte message for line 1 of slot 9:

chsonetexptrace 9.1 64 48656c6c6f20576f726c64

Related Commands

Command Description

chsonetperdi

Change SONET path e-rdi parameters

chsonettrace

Change SONET trace parameters

lssonetlnerdi

List E-RDI information for a SONET line

lssonetlnerdis

List summary E-RDI information for all SONET lines

chsonetln

Change SONET lines.

chsonetln Location [numOfLines MediumType FrameType LoopConfig HCSmasking PayloadScrambling FrameScrambling TxClockSource AdminStatus]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

numOfLines

The number of lines to add. Values: 1-4.

MediumType

The type of physical medium:

1=SONET

2=SDH (reserved for future use)

FrameType

The type of framing:

1=STS-3c

2=STM-1 (reserved for future use)

LoopConfig

The loopback state:

1=No loop

2=Line loop

3=Serial loop

4=Parallel loop

HCSmasking

The HCS masking state (reserved for future use)

PayloadScrambling

The payload scrambling state:

1=Disable

2=Enable

FrameScrambling

The frame scrambling state:

1=Disable

2=Enable

TxClockSource

The clock source for the transmit signal:

1=Loop Timing, use the recovered receive clock

2=Local Timing, use the local clock

3=Through Timing (reserved for future use)

AdminStatus

The desired administrative status of the line:

1=Up

Defaults

numOfLines: 1

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to change the configuration of SONET/SDH interfaces on the OC-3 SCC and back card. Although the SCC may occupy physical slots 9 or 10, you always configure logical slot 9. This command only applies to the OC-3 SCC.

You can change a single line or a range of lines with this command. The system changes lines one at a time and aborts on the first failure, even if subsequent changes could have succeeded. The system issues an error message for partially fulfilled requests.

Examples

The following example activates a line loopback on a SONET line:

chsonetln 9.1 # # # 2

Related Commands

Command Description

addsonetln

Add a SONET line

delsonetln

Delete a SONET line

lssonetln

List information about a SONET line

lssonetlns

List information about all SONET lines

chsonetperdi

Change extended rdi parameters for SONET paths.

chsonetperdi Location [numOfLines SupportPathERDI SignalLabel ExpectedSignalLabel]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

numOfLines

The number of lines to add. Values: 1-4.

SupportPathERDI

The state of the enhanced remote defect indication for the SONET path:

1=Disable

2=Enable

SignalLabel

The signal label to transmit in the SONET path overhead:

1=No specific payload type

19=ATM

207=Packet on SONET

ExpectedSignalLabel

The expected signal label from the SONET path overhead:

1=No specific payload type

19=ATM

207=Packet on SONET

Defaults

numOfLines: 1

SupportPathERDI: 1

SignalLabel: 19

ExpectedSignalLabel: 19

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to enable and configure the e-rdi feature for SONET lines. This feature is disabled by default when you add SONET lines.

Examples

The following example enables e-rdi for SONET line 1 in slot 9:

chsonetperdi 9.1 1 2

Related Commands

Command Description

chsonettrace

Change SONET trace parameters

chsonetexptrace

Change SONET expected trace parameters

lssonetlnerdi

List E-RDI information for a SONET line

lssonetlnerdis

List summary E-RDI information for all SONET lines

chsonettrace

Change path trace parameters for SONET lines.

chsonettrace Location [numOfLines TraceIdLen TraceId TraceIdPosition]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

numOfLines

The number of lines to add. Values: 1-4.

TraceIdLen

The message length for the trace identifier:

16=message contains 16 bytes (SDH only)

64=message contains 64 bytes (SONET or SDH)

TraceId

The trace identifier to transmit in the SONET path overhead. Value: ASCII string of either 16 or 62 characters, depending on the TraceIdLen setting. You specify the ASCII characters as pairs of hexidecimal characters. For example, a you express a space as 20.

Note 1: The 16 byte message normally alters one byte for synchronization, as defined by TraceIdPosition.

Note 2: The 64 byte message uses the last two bytes for synchronization, so the maximum trace identifier length is 62 characters. Only printable ASCII characters are allowed.

TraceIdPosition

The position within a 16-byte message of the synchronization byte. The most significant bit of this byte is set high. Values: 1-16.

Alternatively, this parameter defines the following special cases:

0=No bit set

17=All most significant bits set low

Defaults

numOfLines: 1

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the path trace parameters for SONET lines. This command works in conjunction with the chsonetexptrace and chsonetperdi commands to configure a SONET line test.

Examples

The following example defines a trace identifier of hello world in a 64-byte message for line 1 of slot 9:

chsonettrace 9.1 64 48656c6c6f20576f726c64

Related Commands

Command Description

chsonetperdi

Change SONET path e-rdi parameters

chsonetexptrace

Change SONET expected trace parameters

lssonetlnerdi

List E-RDI information for a SONET line

lssonetlnerdis

List summary E-RDI information for all SONET lines

chsysip1

Change system IP address 1.

chsysip1 Address Mask

Syntax Description

Address

An IP1 address of the management interface in dotted notation w.x.y.z.

Mask

A subnet mask in dotted notation a.b.c.d.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the IP1 address and mask of the system management Ethernet 10BaseT interface.

Examples

The following example configures the IP1 address and subnet mask of a system management interface.

chsysip1 10.2.2.5 255.255.255.0

Related Commands

Command Description

chgw

Change the gateway IP address

chibip

Configure in-band IP

chsysip2

Change system IP2

lsmgips

List management IP addresses

chsysip2

Change system IP address 2.

chsysip2 Address Mask

Syntax Description

Address

An IP2 address of the management interface in dotted notation w.x.y.z.

Mask

A subnet mask in dotted notation a.b.c.d.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure the IP2 address and mask of the system management Ethernet 10BaseT interface.

Examples

The following example configures the IP2 address and subnet mask of a system management interface.

chsysip2 10.2.2.5 255.255.255.0

Related Commands

Command Description

chgw

Change the gateway IP address

chibip

Configure in-band IP

chsysip1

Change system IP1

lsmgips

List management IP addresses

chsyslnmd

Change the line mode to T1 or E1.

chsyslnmd Mode

Syntax Description

Mode

The line mode for the chassis. Values:

1=T1

2=E1

Defaults

No default behavior or values for this command. The default mode for a new chassis is T1.

Command Modes

Security level 1

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to configure the chassis for T1 or E1 lines - you can't mix T1 and E1 lines on a single chassis. Before switching from T1 to E1, verify the following conditions:

When switching from E1 to T1, make sure there are no E1 lines configured. This command automatically resets the chassis.

Examples

The following example changes the chassis to the E1 line mode.

chsyslnmd 2

Related Commands

Command Description

chprotocol

Change the call control protocol for the chassis

chtime

Change time.

chtime H:M:S [Zone]

Syntax Description

H:M:S

The system time in hours, minutes, and seconds delimited by colons. Values: 0-23 for hours and 0-60 for minutes and seconds.

Zone

An integer from 1 to 25, representing a zone.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to configure or change the system time, which may include the time zone. Set 25 integer world time zones from -12 through 0 (GMT) to +12 (see Table 9-4, which lists USA time zones values using civilian designations, such as EST).


Table 9-4: Time Zones
Zone Value Zone Value

gmtplus12

1

gmtminus01

14

gmtplus11

2

gmtminus02

15

gmtplus10

3

gmtminus03

16

gmtplus09

4

gmtminus04

17

gmtplus08

5

est

18

gmtplus07

6

cst

19

gmtplus06

7

pdt

20

gmtplus05

8

pst

21

gmtplus04

9

gmtminus9

22

gmtplus03

10

gmtminus10

23

gmtplus02

11

gmtminus11

24

gmtplus01

12

gmtminus12

25

gmt

13

Examples

The following example sets the system time to noon, Eastern Standard Time.

chtime 12:00:00 18

Related Commands

Command Description

chdate

Change system date

chtimezn

Change system time zone

lsdate

List date

chtimezn

Change system time zone.

chtimezn number

Syntax Description

number

The Time Zone where this MGX 8260 node is installed. Values: 1 - 25

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to change the system time zone. Set 25 integer world time zones from -12 through 0 (GMT) to +12 (see Table 9-4, which lists USA time zones values using civilian designations, such as EST).

Examples

The following example shows how to change the time zone to Pacific Standard Time.

chtimezn 21

Related Commands

Command Description

chdate

Change system date

chtime

Change system time

lsdate

List date

chtmgr

Change trap manager.

chtmgr Addr Port Interface Com_String Bitmap

Syntax Description

Addr

The address of the SNMP manager who wants to receive trap events.

Port

Port to which the traps are transmitted.

Interface

The default interface for initially sending traps if the routing table has no trap manager. Values:

1 = scc-eth-if, the default system Ethernet management interface on SCC.

2 = inband-if, the in-band management interface.

3 = ppp-if, the PPP interface.

Com_String

SNMP community string for the trap manager.

Bitmap

A bitwise specification of trap categories to subscribe. Each bit represents a category of traps. Bit values: 1 = subscribe 0, = do not subscribe. Trap subscription bitmap specifications are:

Bit 0=Major (trap severity selection)

Bit 1=Minor (trap severity selection

Bit 2=Information (trap severity selection)

Bit 3=Shelf

Bit 4=Card

Bit 5=SNMP

Bit 6=Dsx1 Line

Bit 7=Dsx3 Line

Bit 8=Sonet Line

Bit 9=Ethernet Line

Bit 10=Voice Port

Bit 11=Ethernet Channel

Bit 12=Voice Channel

Bit 13=EMM

Bit 14=Clock

Bit 15=DSP

Bit 16=DMCMAP

Bit 17=ISDN

Bit 18=MGCP

Bit 19=Backhaul Session

The first three bit positions indicate which trap severity categories they are interested in. If you specify severity without specifying any other trap categories, managers receive traps from all categories.

Defaults

Port: 162

Interface: 1

Com_String: "public"

Bitmap: 0

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Network administrators can receive email for up to 20 traps. Use this command to change a manager's SNMP trap registrations.

Examples

The following example changes the manager at address 10.1.1.10 and udp port 162 to receive events for the traps specified by bitmap 1100110.

The bitmap is a binary number that represents the settings.

Trap dsx1line SNMP Information Minor
Value

1

1

0

0

1

1

0

Bit

6

5

4

3

2

1

0

To use this bitmap, convert it to a decimal value and specify it as the last argument. Binary 1100110 is 102 decimal. Therefore, you enter the command as follows:

chtmgr 10.1.1.10 2 162 public 102

The second argument (2) sets the in-band interface as the default interface for sending traps when the routing table has no trap manager.

Related Commands

Command Description

addcms

Add community string

addtmgr

Add trap manager

deltmgr

Delete trap manager

lstmgr

List trap manager

lstmgrs

List trap managers

chvport

Configure voice port.

chvport SlotNum PortNum RepitionNum WrapNum [Dejitter DejitteBufLen Maxdj Mindj PacketLoading EchoTail]

Syntax Description

SlotNum

The logical slot number of an NSC. Values: 1 to 16

PortNum

The logical port number. Values 1 to 512

ReptitionNum

The number of ports to add. Values: 1 to 6944. This corresponds to 31 ports per line, 16 lines per NSC, and 14 NSCs.

WrapNum

The DS0 number at which to wrap to the next slot. Set this to the maximum number of DS0s the NSC in your configuration. For DS1 use 384 and for E1 use 480 with CAS or 496 without CAS. Values: 1 to 512

Dejitter

The desired state, disabled or enabled, of the dejitter buffer. Values: 1 or 2, respectively.

DejitteBufLen

The initial length of the dejitter buffer, specified in multiples of 10 msec. Values: 1 through Maxdj.

Maxdj

The maximum length of the dejitter buffer, specified in multiples of 10 msec. Values: 1 through 50.

Mindj

The minimum length of the dejitter buffer, specified in multiples of 10 msec. Values: 1 through DejitterBufLen.

PacketLoading

The IP packet loading time for voice service, expressed in multiples of 10 msec. Values: 1 - 10.

EchoTail

The length of the echo cancel tail:

1 = echo disabled

2 = tail24ms—24 msecs

3 = tail32ms—32 msecs

4 = tail48ms—48 msecs

5 = tail64ms—64 msecs

6 = tail80ms—80 msecs

6 = tail96ms—96 msecs

7 = tail112ms—112 msecs

8 = tail128ms—128 msecs

Defaults

ReptitionNum: 1

WrapNum: 384 for DS1, 480 for E1 (CAS on)

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added repetition and wrap numbers

Usage Guidelines

Use this command to configure one or more voice ports.

Examples

The following example disables the dejitter buffer for 4 lines starting slot 1 port 1.

chvport 1 1 # 384 1

The system changes the packet loading for logical port one in slot one to 20 msec.

Related Commands

Command Description

addvport

Add voice port

delvport

Delete voice port

lsvport

List voice port

lsvports

List voice ports

clralmhist

Clear alarm history.

clralmhist

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete alarm history.

Examples

The following example clears the alarm history.

clralmhist

Related Commands

Command Description

lsalms

List alarms

clrcdcnf

Clear configuration of a card.

clrcdcnf Num

Syntax Description

Num

The slot number of the card

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Clears the configuration of the specified card and resets it.

Examples

The following example clears the configuration of the card in slot 3.

clrcdcnf 3

Related Commands

Command Description

chcdif

Configure card interface

clrds1lnst

Clear T1 line statistics.

clrds1lnst Location Stat

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line.

Stat

The statistic to clear: Values: one of the following integers.

1=No Action.

2=Clear all the counters in the ds1Stats Table and dsx1StatsPerfAlarmState.

3=Clear LCV 15 Minute counter in the dsx1CurrentTable.

4=Clear LCV 24 Hour counter in the dsx1TotalTable.

5=Clear LES 15 Minute counter in the dsx1CurrentTable.

6=Clear LES 24 Hour counter in the dsx1TotalTable.

7=Clear LSES 15 Minute counter in the dsx1CurrentTable.

8=Clear LSES 24 Hour counter in the dsx1TotalTable.

9=Clear PCV 15 Minute counter in the dsx1CurrentTable.

10=Clear PCV 24 Hour counter in the dsx1TotalTable.

11=Clear PES 15 Minute counter in the dsx1CurrentTable.

12=Clear PES 24 Hour counter in the dsx1TotalTable.

13=Clear PSES 15 Minute counter in the dsx1CurrentTable.

14=Clear PSES 24 Hour counter in the dsx1TotalTable.

15=Clear SEFS 15 Minute counter in the dsx1CurrentTable.

16=Clear SEFS 24 Hour counter in the dsx1TotalTable.

17=Clear PSAS 15 Minute counter in the dsx1CurrentTable.

18=Clear PSAS 24 Hour counter in the dsx1TotalTable.

19=Clear UAS 15 Minute counter in the dsx1CurrentTable.

20=Clear UAS 24 Hour counter in the dsx1TotalTable.

21=Clear all counters in the dsx1CurrentTable (15 minute counters).

22=Clear all counters in the dsx1TotalTable (24 hour counters).

23=Clear Bursty Errored Seconds in dsx1CurrentTable.

24=Clear Bursty Errored Seconds in dsx1TotalTable.

25= Clear Path Controlled Slip Seconds in the dsx1CurrentTable

26=Clear Path Controlled Slip Seconds in the dsx1TotalTable

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to clear the specified DS1 real-time statistic.

Examples

The following example clears the LCV 24 Hour counter in the dsx1TotalTablefor the DS1 line at slot 1 line 1.

clrds1lnst 1.1 4

Related Commands

Command Description

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

offbertds1

Stop BERT on DS1

onbertds1

Start BERT on DS1

clrds3lnst

Clear statistics for DS3 line.

clrds3lnst Index stats

Syntax Description

Index

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

stats

The instruction to clear or not to clear statistics.

1=Do not clear.

2=Clear

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card configuration - no functional change

Usage Guidelines

Clears the specified DS3 real-time statistic.

Examples

The following examples clears the DS3 statistic at slot 7, line 1.

clrds3lnst 7.1 2

Related Commands

Command Description

lsds3curst

List DS3 current statistics

lsds3cursts

List all DS3 statistics

lsds3intst

List DS3 interval statistics

lsds3ln

List DS3 line

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

clre1lnst

Clear E1 line statistics.

clrds1lnst Location Stat

Syntax Description

Location

The slot and line number, delimited by a period, of the line.

Stat

The statistic to clear: Values: one of the following integers.

1=No Action.

2=Clear all the counters in the e1Stats Table and e1StatsPerfAlarmState

3= Clear LCV 15 Minute counter in the e1CurrentTable

4=Clear LCV 24 Hour counter in the e1TotalTable

5=Clear LES 15 Minute counter in the e1CurrentTable

6=Clear LES 24 Hour counter in the e1TotalTable

7=Clear UAS 15 Minute counter in the e1CurrentTable

8=Clear UAS 24 Hour counter in the e1TotalTable

9=Clear FEESR 15 Minute counter in the e1CurrentTable

10=Clear FEESR 24 Hour counter in the e1TotalTable

11=Clear FESESR 15 Minute counter in the e1CurrentTable

12=Clear FESESR 24 Hour counter in the e1TotalTable

13=Clear FEBEESR 15 Minute counter in the e1CurrentTable

14=Clear FEBEESR 24 Hour counter in the e1TotalTable

15=Clear FEBESESR 15 Minute counter in the e1CurrentTable

16=Clear FEBESESR 24 Hour counter in the e1TotalTable

17=Clear CRCESR 15 Minute counter in the e1CurrentTable

18=Clear CRCESR 24 Hour counter in the e1TotalTable

19=Clear CRCSESR 15 Minute counter in the e1CurrentTable

20=Clear CRCSESR 24 Hour counter in the e1TotalTable

21=Clear ESR 15 Minute counter in the e1CurrentTable

22=Clear ESR 24 Hour counter in the e1TotalTable

23=Clear SESR 15 Minute counter in e1CurrentTable

24=Clear SESR 24 Hour counter in e1TotalTable

25=Clear ES in e1CurrentTable

26=Clear ES in e1TotalTable

27=Clear SES in e1CurrentTable

28=Clear SES in e1ToatlTable

29=Clear BES in e1CurrentTable

30=Clear BES in e1TotalTable

Stat
Cont.

31=Clear PCV in e1CurrentTable

32=Clear PCV in e1TotalTable

33=Clear Control Slip seconds in e1CurrentTable

34=Clear Control Slip seconds in e1TotalTable

35=Clear all counters in e1CurrentTable

36=Clear all counters in e1TotalTable

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to clear the specified E1 real-time statistic.

Examples

The following example clears the LCV 24 Hour counter in the dsx1TotalTablefor the E1 line at slot 1 line 1.

clre1lnst 1.1 4

Related Commands

Command Description

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

offbertds1

Stop BERT on DS1

onbertds1

Start BERT on DS1

clrevt

Clear event log.

clrevt

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to clear the event log.

Examples

The following example clears the event log.

clrevt

Related Commands

Command Description

lsevt

List events

clrndcnf

Clear node configuration and restore defaults.

clrndcnf

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to clear configuration of a node and restore the default settings. Use with caution because this interrupts service and changes many parameters.

Examples

The following example clears configuration settings of a node.

clrndcnf

Related Commands

Command Description

resetnd

Reset node

clrslinecst

Clear current statistics for a SONET line.

clrslinecst Location [Stat]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Stat

The statistic to clear: Values: one of the following integers:

1=No Action

2=All

3=ES

4=SES

5=CV

6=UAS

Defaults

Stat: 1

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to clear the specified statistic.

Examples

The following example clears the SES counter in the sonet line at slot 9 line 1.

clrds1lnst 9.1 4

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

clrslinetst

Clear total statistics for a SONET line.

clrslinetst Location [Stat]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Stat

The statistic to clear: Values: one of the following integers:

1=No Action

2=All

3=ES

4=SES

5=CV

6=UAS

Defaults

Stat: 1

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to clear the specified statistic.

Examples

The following example clears the SES counter in the sonet line at slot 9 line 1.

clrslinetst 9.1 4

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

clrsonetstats

Clear the SONET alarm statistics.

clrspathtst Location [Stat]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Stat

The statistic to clear: Values: one of the following integers:

1=noAction

2=clearAll

3=clearSeCV15Min

4=clearSeCV24Hr

5=clearSeES15Min

6=clearSeES24Hr

7=clearSeSES15Min

8=clearSeSES24Hr

9=clearSeSEFS15Min

10=clearSeSEFS24Hr

11=clearLCV15Min

12=clearLCV24Hr

13=clearLES15Min

14=clearLES24Hr

15=clearLSES15Min

16=clearLSES24Hr

17=clearLUAS15Min

18=clearLUAS24Hr

19=clearPCV15Min

20=clearPCV24Hr

21=clearPES15Min

22=clearPES24Hr

23=clearPSES15Min

24=clearPSES24Hr

25=clearPUAS15Min

26=clearPUAS24Hr

27=clearAll15Min

28=clearAll24Hr

Defaults

Stat: 1

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to clear the specified alarm statistic.

Examples

The following example clears all SONET alarm counters at slot 9 line 1.

clrsonetstats 9.1 2

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrspathcst

Clear current statistics for a SONET path.

clrspathcst Location [Stat]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Stat

The statistic to clear: Values: one of the following integers:

1=No Action

2=All

3=ES

4=SES

5=CV

6=UAS

Defaults

Stat: 1

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to clear the specified statistic.

Examples

The following example clears the SES counter in the sonet path at slot 9 line 1.

clrds1lnst 9.1 4

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

clrspathtst

Clear total statistics for a SONET path.

clrspathtst Location [Stat]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Stat

The statistic to clear: Values: one of the following integers:

1=No Action

2=All

3=ES

4=SES

5=CV

6=UAS

Defaults

Stat: 1

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to clear the specified statistic.

Examples

The following example clears the SES counter in the sonet path at slot 9 line 1.

clrspathtst 9.1 4

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

clrssectioncst

Clear current statistics for a SONET section.

clrssectioncst Location [Stat]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Stat

The statistic to clear: Values: one of the following integers:

1=No Action

2=All

3=ES

4=SES

5=SEFS

6=CV

Defaults

Stat: 1

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to clear the specified statistic.

Examples

The following example clears the SES counter in the sonet section at slot 9 line 1.

clrds1lnst 9.1 4

Related Commands

Command Description

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

clrssectiontst

Clear total statistics for a SONET section.

clrssectiontst Location [Stat]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Stat

The statistic to clear: Values: one of the following integers:

1=No Action

2=All

3=ES

4=SES

5=SEFS

6=CV

Defaults

Stat: 1

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to clear the specified statistic.

Examples

The following example clears the SES counter in the sonet section at slot 9 line 1.

clrssectiontst 9.1 4

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

clrtraps

Clear the trap log.

clrtraps

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to clear the log of SNMP traps.

Examples

The following example clears the trap log.

clrtraps

Related Commands

Command Description

lstraps

List traps

dbbkup

Back up the configuration database.

dbbkup

Syntax Description

The command has no arguments or keywords.

Defaults

The system defines a backup file name.

Command Modes

Security level 1

Command History

Release Modification

1.1

This command was first introduced.

Usage Guidelines

Use this command to save all configuration information, such as system and line settings, to the hard drive on the SCC. This command returns the outcome of the operation and the name assigned to the backup file. You can restore this configuration at a later time with the dbrstr command.

Examples

The following example backs up the MGX 8260 database.

dbbkup

The system returns the backup result and name of the backup file. For example:

dbbackup: Successful back-up of configuration file [C:/scc_mms111.cfg]

Related Commands

Command Description

dbrstr

Database restore

dbrstr

Restore the configuration database.

dbrstr fileName

Syntax Description

fileName

The name of the backup file, without the .cfg extension.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.1

This command was first introduced.

Usage Guidelines

Use this command to restore the configuration information saved by dbbkup. Use the file name assigned by dbbkup, but omit the .cfg extension.

Examples

The following example restores configuration information from file scc_mms111.cfg.

dbrstr scc_mms111

Related Commands

Command Description

dbbkup

Database backup

deacannfile

Deactivate an announcement file.

deacannfile fid

Syntax Description

fid

The announcement file ID. Values: 1-100

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

You use this command to deactivate an announcement file. Before attempting to remove an announcement file, first deactivate the file; otherwise, removal fails. To view file ID numbers, use the lsannfiles command.

Examples

The following command deactivates announcement file 25:

deacannfile 25

Related Commands

Command Description

acannfile

Activate an announcement file

rmannfile

Remove an announcement file

lsannfile

List the given announcement file

lsannfiles

List all announcement files

lsdurationif

List duration information about announcement files

delcms

Delete community string.

delcms Comm_Str Addr

Syntax Description

Comm_Str

An SNMP community string, up to 20 characters.

Addr

The IP address of the SNMP manager who wants to discontinue receiving trap events

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete the community string for an SNMP manager who wants to discontinue receiving information on traps.

Examples

For example, the following command deletes the Public community string.

delcms Public 0.0.0.0

Related Commands

Command Description

addcms

Add community string

deltmgr

Delete trap manager

lscms

List community string

lscmss

List community strings

deldchan

Delete a D Channel.

deldchan Index Repetitions

Syntax Description

Index

The slot and line number, delimited by a period, of the D channel

Repetitions

The number of sequential D Channels to delete. Values: 1 to 1136.

Defaults

Repetitions: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added number of repetitions

Usage Guidelines

Use this command to delete a D Channel management path, freeing the resource for other uses.

Examples

The following example deletes three D Channels, starting at slot 5, line 4.

deldchan 5.4 3

Related Commands

Command Description

adddchan

Add a D Channel

lsdchan

List information about a D Channel

lsdchans

List information about D Channels

deldlsp

Delete a DLSAP profile.

deldlsp Index

Syntax Description

Index

The identifier of a DLSAP Profile. Values: 1 - 10.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to deletes a DLSAP profile from the MGX 8260 Media Gateway. Profiles used by existing D Channels should not be deleted.

Examples

The following example deletes profile 9.

deldlsp 9

Related Commands

Command Description

adddlsp

Add a DLSAP profile

lsdlsapstat

List statistics for a DLSAP

lsdlsapstats

List DLSAP statistics

lsdlsapstatus

List status for a DLSAP

lsdlsp

List a DLSAP profile

lsdlsps

List DLSAP profiles

delds1ln

Delete DS1(T1 or E1) lines.

delds1ln Index Numlines

Syntax Description

Index

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

Numlines

Number of lines to delete. The MGX 8260 stops deleting lines at the first failure. Values: 1-1136.

Defaults

Numlines: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.2

Added E1 lines

Usage Guidelines

Use this command to delete a one or more DS1/E1 lines. You can't delete a DS1/E1 line if a voice port is configured for the line. When deleting a range of lines, the process stops after the last line or at the first error.

Examples

The following example deletes 3 DS1 lines beginning at line 6 from slot 13:

delds1ln 13.6 3

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

delds3ln

Delete a DS3 line.

delds3ln Index Numlines

Syntax Description

Index

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

Numlines

Number of lines to delete.

Defaults

Numlines: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card configuration - no functional change

Usage Guidelines

Use this command to delete a one or more DS3 lines. When deleting a range of lines, the process stops after the last line or at the first error.

Examples

The following example deletes three DS3 lines beginning at line 5 in slot 7:

delds3ln 7.2 3

Related Commands

Command Description

addds3ln

Add DS3 line.

chds3alm

Change DS3 alarm severity and threshold

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List DS3 current statistics

lsds3intst

List DS3 interval statistics

lsds3ln

List DS3 line

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

delereg

Delete email registration.

delereg Index

Syntax Description

Index

Position of the email address in the SnmpEmailRegTable. Values: integer.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to stop email notifications to the user.

Examples

The following example deletes all email alerts for user 1:

delereg 102

Related Commands

Command Description

addereg

Add email registration

chem

Configure email registration

chereg

Change email registration

lsem

List email server

lsereg

List entry registered

lseregs

List registered email alerts

delethln

Delete Ethernet line.

delethln Location

Syntax Description

Location

The slot and line number, delimited by a period, of the Ethernet line. Values: The slot number of the SCC, either 9 or 10; the Fast Ethernet line number, from 1 to 4.

Defaults

No default values or behavior.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete an Ethernet interface from the Fast Ethernet SCC and back card.

Examples

The following example deletes Fast Ethernet line 4 in slot 9:

delethln 9.4

Related Commands

Command Description

addethln

Add Ethernet line

chethln

Change Ethernet line

upethln

Activate Ethernet line

dnethln

DeActivate Ethernet line

lsethln

List Ethernet line

lsethlns

List Ethernet Lines

deliproute

Delete an IP route.

deliproute IPRouteDest

Syntax Description

IPRouteDest

The destination IP address of this route. An entry of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to them is dependent on the table-access mechanisms defined by the network management protocol.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to delete an IP route from the MGX 8260 Media Gateway routing table.

Examples

The following example deletes indirect IP route 10.1.1.1:

deliproute 10.1.1.1

Related Commands

Command Description

addiproute

Add an IP route

lsiproute

List an IP route

lsiproutes

List IP routes

delm13

Delete DS1 to DS3 map.

delm13 DS3Line DS1Line NumLines

Syntax Description

DS3Line

The number of the source DS3 line. When deleting more than one DS1, the range may span additional DS3s. Values: 1 - 6

DS1Line

The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28

NumLines

The number of map pairs to add. Values: 1 - 192, depending on the number of mappings in a contiguous sequence

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete one or more DS3 to DS1 mappings from Distribution Matrix Card (DMC) to the Narrowband Service Card (NSC). To delete a single point, omit the NoOfLines argument.

Examples

The following example deletes three sequential map table entries, starting at DS3 line 1, DS1 line 1:

delm13 1 1 3

Related Commands

Command Description

addm13

Add map to DS1 from DS3

chm13

Change DS1 to DS3 map

lsm13

List DS3-to-DS1 mapping

lsm13s

List DS3-to-DS1 mappings

delmacsapprof

Delete a MACSAP profile.

delmacsapprof Index

Syntax Description

Index

This object is the identifier of a MAC SAP. Values: 1 - 16.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete a MACSAP profile from the MGX 8260 Media Gateway. Profiles used by existing D Channels should not be deleted.

Examples

The following example deletes profile 3.

delmacsapprof 3

Related Commands

Command Description

addmacsapprof

Add a MACSAP profile

lsmacsapprof

List information about a MACSAP profile

lsmacsapprofs

List all MACSAP profiles

lsmacsapstat

List statistics for a MACSAP interface

lsmacsapstats

List MACSAP statistics

delreds

Delete a card redundancy pair.

delreds Slot1 Slot2

Syntax Description

Slot1

Physical location of the primary card in the chassis. Valid settings: 1-8 and 11-16.

Slot2

Physical location of the secondary card in the chassis. Valid settings: 1-8 and 11-16.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete card redundancy between the primary and secondary slot.

Examples

The following example deletes the redundancy relationship between cards 1 and 3.

delreds 1 3

Related Commands

Command Description

addreds

Add a card redundancy pair

lsreds

List card redundancy pairs

swcd

Switch to redundant NSC

delsess

Delete an MGCP session manager.

delsess SessionSetId GroupId SessionId

Syntax Description

SessionSetId

The index of the session set to which the group containing the session manager belongs. Values: 1-6.

GroupId

The index of the session group to which the session manager belongs. Values: 1 or 2.

SessionId

The index of this session. Values: 1 or 2

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete a session manager from a session group.

Examples

The following example deletes session manager 1 from session group 1 of set 1:

delsess 1 1 1

Related Commands

Command Description

addsess

Add a session manager

addsset

Add a session set

addsgrp

Add a session group

delsset

Delete a session set

delsgrp

Delete a session group

delsgrp

Delete an MGCP session group

delsgrp SessionSetId GroupId Repetitions

Syntax Description

SessionSetId

The index of this session. Values: 1 or 2

GroupId

The index of the session group to which the session manager belongs. Values: 1 or 2

Repetitions

The number of groups to delete

Defaults

Repetitions: 1

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete a session group from a session set.

Examples

The following example deletes session group 1 from session set 1:

delsgrp 1 1

Related Commands

Command Description

addsess

Add a session manager

addsset

Add a session set

addsgrp

Add a session group

delsess

Delete a session manager

delsset

Delete a session set

delsonetln

Delete SONET lines.

delsonetln Location [numOfLines]

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

numOfLines

The number of lines to delete. Values: 1-4.

Defaults

numOfLines: 1

Command Modes

Security level 3

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to delete SONET lines from the OC-3 SCC and back card. You can delete a single line or a range of lines with this command. The system deletes lines one at a time and aborts on the first failure, even if subsequent changes could have succeeded. The system issues an error message for partially fulfilled requests.

Examples

The following example deletes SONET lines 3 and 4 in slot 9:

delethln 9.3 2

Related Commands

Command Description

addsonetln

Add a SONET line

chsonetln

Change a SONET line

lssonetln

List information about a SONET line

lssonetlns

List information about all SONET lines

delsrt

Delete a static route.

delsrt Addr Location

Syntax Description

Addr

An address in dotted notation w.x.y.z of the destination of an existing static route

Location

The slot and line number, delimited by a period, of the origin of the static route

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Deletes a static route from an MGX 8260 Media Gateway to a network IP address.

Examples

The following example deletes a static route from slot 1 line 1 of the MGX 8260 Media Gateway to IP address 12.1.1.0.

delsrt 12.1.1.0 1.1

Related Commands

Command Description

addsrt

Add static route

lssrt

List information about a static route

lssrts

List information about all static routes

delsset

Delete an MGCP session set.

delsset SessionSetId

Syntax Description

SessionSetId

The index of the session set to which the group containing the session manager belongs. Values: 1-6.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete a session set.

Examples

The following example deletes session set 1:

delsset 1

Related Commands

Command Description

addsess

Add a session manager

addsgrp

Add a session group

delsess

Delete a session manager

delsset

Delete a session set

delsgrp

Delete a session group

deltmgr

Delete trap manager.

deltmgr Addr

Syntax Description

Addr

The address of the SNMP manager who wants to discontinue notification of trap events.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Deletes a manager from the registered list to receive SNMP trap events.

Examples

The following example deletes the manager entry at address 10.2.2.5.

deltmgr 10.2.2.5

Related Commands

Command Description

addtmgr

Add trap manager

delcms

Delete community string

lstmgrs

List information about all trap managers

lstmgr

List information about a trap manager

delusp

Delete user profile.

delusp Name

Syntax Description

Name

The login name of a user

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to remove the profile of a user from the system.

Examples

The following example deletes a user profile for a user named booter.

delusp booter

Related Commands

Command Description

addusp

Add user profile

chkey

Change file key

delvport

Delete voice port

delvport Slot Port RepetitionNum WrapNum

Syntax Description

Slot

The logical slot number of an NSC

Port

The logical port number

RepetitionNum

The number of ports to add. Values: 1 to 6944. This corresponds to 31 ports per line, 16 lines per NSC, and 14 NSCs.

WrapNum

The DS0 number at which to wrap to the next slot. Set this to the maximum number of DS0s the NSC in your configuration. For DS1 use 384 and for E1 use 480 with CAS or 496 without CAS. Values: 1 to 512

Defaults

RepetitionNum: 1

WrapNum: 384 for DS1, 480 for E1 (CAS on)

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to delete a voice port.

Examples

The following example deletes a voice port from slot 1, line 1.

delvport 1 1

Related Commands

Command Description

addvport

Add voice port

chvport

Change voice port

lsvport

List voice port

lsvports

List voice ports

dnethln

Down Ethernet line.

dnethln Location

Syntax Description

Location

The slot and line number, delimited by a period, of the Ethernet line

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Deactivates an Ethernet interface.

Examples

The following example brings down the Ethernet interface from the MGX 8250 Media Gateway at slot 7 line 1, address 10.1.2.10.

dnethln 9.1

Related Commands

Command Description

addethln

Add Ethernet line

chethln

Change Ethernet line

delethln

Delete Ethernet line

lsethln

List Ethernet line

lsethlns

List Ethernet Lines

upethln

Activate Ethernet line

exit

Log out.

exit

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Type this command to log out from the MGX 8260 Media Gateway

Examples

The following command logs out.

exit

Related Commands

Command Description

bye

Logs out from the MGX 8260 Media Gateway.

logout

Logs out from the MGX 8260 Media Gateway.

help

Display command help.

help [command]

Syntax Description

command

The command for which you want help.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command without an argument to list the commands available at your security level. To obtain usage information for a command, specify the command name as an argument.

Examples

The following example displays help for the htmlversion command.

help htmlversion

htmlversion

Display the HTML version.

htmlversion

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display version information for WebViewer HTML files.

Examples

The following example displays the HTML version.

htmlversion

logout

Logout of the MGX 8260 Media Gateway.

logout

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to end the session with the MGX 8260 Media Gateway.

Examples

The following example logs out.

logout

Related Commands

Command Description

bye

Log out

lsacp

List information on an active call

lsacp Slot Line ID

Syntax Description

Slot

The physical source (slot number) of an active call. Values: 1-16.

Line

The physical source (line number) of an active call. Values: 1-16.

ID

The DS0 used by an active call. Values: 1-24.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list information about the call using a specific MGX 8260 resource. The slot, line, and DS0 is valid for a given time only, because the resource is re-used after the current active call is torn down.

Examples

The following example lists information on the call on slot 1, line 1, DS0 1:

lsacp 3 1 1

Related Commands

Command Description

lsacps

List all active calls by resource

lsact

List an active call by transaction ID

lsacts

List all active calls by transaction

lsacps

List all active calls by resource

lsacps

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to lists active calls for all slots, lines, and DS0s. Output includes the log port, and packets received and transmitted.

Examples

The following examples lists active calls.

lsacps

Related Commands

Command Description

lsacp

List active call by resource

lsact

List an active call by transaction ID

lsacts

List all active calls by transaction

lsact

List an active call by transaction ID.

lsact ID

Syntax Description

ID

A unique identifier of an active call. Values: index number

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list active call information for a specific transaction ID. The transaction ID is re-used after the current active call is torn down.

Examples

The following example lists the call identified by transaction ID 2315

lsact 2315

Related Commands

Command Description

lsacp

List active call by resource

lsacps

List all active calls by resource

lsacts

List all active calls by transaction

lsacts

List all active call by transaction.

lsacts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Output includes the transaction number, the slot, line, and DS0 of the source, the log port, and the packets received and transmitted.

Examples

The following example lists the call identified by transaction ID 2315

lsacts

Related Commands

Command Description

lsacp

List active call by resource

lsacps

List all active calls by resource

lsact

List active call by transaction ID

lsalms

List alarms.

lsalms

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays the status of all shelf alarms and card and software errors. For more information, see Monitoring Shelf Alarms.

Examples

The following example lists alarms.

lsalms

Related Commands

Command Description

clralmhist

Clear alarm history

lsannfile

List the given announcement file.

lsannfile fid

Syntax Description

fid

The announcement file ID. Values: 1-100

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

You use this command to list information about the given announcement file. For more information, see Viewing Announcement Files.

Examples

The following command lists announcement files 62.

lsannfile 62

Related Commands

Command Description

acannfile

Activate an announcement file

deacannfile

Deactivate an announcement file

rmannfile

Remove an announcement file

lsannfiles

Lists all announcement files

lsdurationif

List duration information about announcement files

lsannfiles

List all announcement files.

lsannfiles

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

You use this command to list all announcement files. For more information, see Viewing Announcement Files.

Examples

The following command lists all announcement files.

lsannfiles

Related Commands

Command Description

acannfile

Activate an announcement file

deacannfile

Deactivate an announcement file

rmannfile

Remove an announcement file

lsannfile

List the given announcement file

lsdurationif

List duration information about announcement files

lsbertds1

List DS1 BERT results.

lsbertds1 Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays the bit error rate status of the specified DS1 line. Use in conjunction with onbertds1 and offbertds1 to test a DS1 line. For more information, see DS1/E1 BERT Test.

Examples

The following example shows the BERT status of the DS1 line at slot 11 line 1.

lsbertds1 11.1

Related Commands

Command Description

offbertds1

Stop BERT on DS1

onbertds1

Start BERT on DS1

lscd

List card details.

lscd CardNum

Syntax Description

CardNum

The card about which you want information. Values: 1-16.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list the physical and logical card number, front, back, and daughter card types, the state and service of the card, revision information, serial numbers, alarm information, the ATM queue profile number, the RAM backup, interface mode, and more. For more information, see Viewing Card Configuration and Status.

Examples

The following example lists information about card 8.

lscd 8

Related Commands

Command Description

lscds

Lists information about all physical cards.

resetcd

Resets the specified card.

lscds

List cards .

lscds

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list information on all cards. For more information, see Viewing Summary Information for Cards.

Examples

The following example lists information about all cards.

lscds

Related Commands

Command Description

lscd

Lists information about the specified physical card.

resetcd

Resets the specified card.

lsclksrcs

List all clock sources.

lsclksrcs

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display all clock sources. For more information, see Viewing Clock Parameters.

Examples

The following example lists clock sources.

lsclksrcs

Related Commands

Command Description

chpclksrc

Change primary clock parameters

chsclksrc

Change secondary clock parameters

swclk

Switch clock

lscms

List a community strings.

lstmgr Index

Syntax Description

Index

The index number of the community string

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays information about the community string and SNMP manager IP address. For more information, see Assigning a tftp Security Key.

Examples

The following example lists information about community string 1.

lscms 1

Related Commands

Command Description

addtmgr

Add trap manager

clrtraps

Clear traps

delcms

Delete community string

lscmss

List community strings

lstmgrs

List trap managers

lscmss

List trap managers.

lscmss

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display summary information about all community strings. For more information, see Assigning a tftp Security Key.

Examples

The following example lists all community strings.

lscmss

Related Commands

Command Description

addtmgr

Add trap manager

clrtraps

Clear traps

delcms

Delete community string

lscms

List community string

lstmgr

List trap manager

lsdate

List system date, time, and time zone.

lsdate

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the system time and date. For more information, see Viewing Node Parameters.

Examples

The following example displays node information.

lsdate

Related Commands

Command Description

chdate

Change the date and time

lsdchan

List information about a D Channel.

lsdchan Index

Syntax Description

Index

The slot and line number, delimited by a period, of the new D Channel.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list information about a D Channel, such as its frame length, DS0, retransmission count, and more. For more information, see Viewing D Channels.

Examples

The following example lists a D Channel of line 1 on slot 14:

lsdchan 14.1

Related Commands

Command Description

adddslp

Add a DLSAP profile

addmacsapprof

Add a MACSAP profile

deldchan

Delete a D Channel

lsdchans

List information about D Channels

lsdchans

List information about all D Channels.

lsdchans

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list information about all D Channels. For more information, see Viewing D Channels.

Examples

The following example lists information about all D Channels:

lsdchans

Related Commands

Command Description

adddslp

Add a DLSAP profile

addmacsapprof

Add a MACSAP profile

deldchan

Delete a D Channel

lsdchan

List information about a D Channel

lsdlsapstat

List statistics for a DLSAP.

lsdlsapstat Index

Syntax Description

Index

The identifier of a DLSAP Profile. Values: 1 - 20.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list statistics for a DLSAP, such as received and transmitted information frames, receive ready frames, disconnect frames, frame reject frames, and more. For more information, see Viewing DLSAP Statistics.

Examples

The following example lists a D Channel of line 1 on slot 14:

lsdlsapstat 2

Related Commands

Command Description

adddslp

Add a DLSAP profile

addmacsapprof

Add a MACSAP profile

deldchan

Delete a D Channel

lsdchans

List information about D Channels

lsdlsapstats

List DLSAP statistics.

lsdlsapstats

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list summary DLSAP statistics. For more information, see Viewing DLSAP Statistics.

Examples

The following example lists DLSAP statistics.

lsdlsapstats

Related Commands

Command Description

adddslp

Add a DLSAP profile

addmacsapprof

Add a MACSAP profile

deldchan

Delete a D Channel

lsdchans

List information about D Channels

lsdlsapstatus

List status for a DLSAP.

lsdlsapstatus Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list the DLSAP status for the DS1 line, including outstanding frames, number of frames dropped by MAC, the busy status, flow control state, retransmission count, queue size, and active SAPs and DLCs. For more information, see Viewing DLSAP Status.

Examples

The following example lists the DLSAP status of line 1 on slot 11.

lsdlsapstatus 11.1

Related Commands

Command Description

deldlsp

Delete a DLSAP profile

lsdlsapstat

List statistics for a DLSAP

lsdlsapstats

List DLSAP statistics

lsdlsp

List a DLSAP profile

lsdlsps

List DLSAP profiles

lsdlsp

List a DLSAP profile.

lsdlsp Num

Syntax Description

Num

The DLSAP profile number associated with the D Channel. Values: 1-20.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list the DLSAP profile information, including frame length, window size, retranmission count, timer, modulo, DLC, and TEI information. For more information, see Viewing DLSAP Profiles.

Examples

The following example lists the information for DLSAP profile 5.

lsdlsp 5

Related Commands

Command Description

deldlsp

Delete a DLSAP profile

lsdlsapstat

List statistics for a DLSAP

lsdlsapstats

List DLSAP statistics

lsdlsapstatus

List status for a DLSAP

lsdlsps

List DLSAP profiles

lsdlsps

List summary DLSAP profile information.

lsdlsps

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list summary DLSAP information for all profiles. For more information, see Viewing DLSAP Profiles.

Examples

The following example lists the information for DLSAP profiles.

lsdlsps

Related Commands

Command Description

deldlsp

Delete a DLSAP profile

lsdlsapstat

List statistics for a DLSAP

lsdlsapstats

List DLSAP statistics

lsdlsapstatus

List status for a DLSAP

lsdlsp

List a DLSAP profile

lsds0

List a DS0 entry.

lsds0 Num

Syntax Description

SlotNum

The slot number of the card with the DS1 line. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

SlotNum

The DS1 line number with the DS0 channel. Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

DS0Num

The number of the DS0 channel. Valid entries: 1-24 for DS1 and 1-31 for E1

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list information on the specified DS0.

Examples

The following example lists information on channel 1 of line 1 in slot 11.

lsds0 11 1 1

lsds0s

List all DS0 entries.

lsds0s

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list all configured DS0.

Examples

The following example lists all DS0 entries.

lsds0s

lsds1alm

List all alarm thresholds for a DS1 line.

lsds1alm Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list DS1 line alarm thresholds, such as Red, RAI, and Perf Alarm Severity. For more information, see Viewing DS1 Alarm Thresholds.

Examples

The following example lists DS1 alarm threshold levels for line 1 of slot 11.

lsds1alm 11.1

lsds1curst

List DS1 current statistics.

lsds1cursts Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the performance statistics of the current 15-minute collection period for the specified DS1 line. For more information, see Viewing Current T1 Statistics.

Examples

The following example shows the performance statistics of the DS1 line at slot 1 line 1.

lsds1curst 1.1

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

lsds1cursts

List DS1 current statistics.

lsds1cursts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the performance statistics of the current 15-minute collection period for all DS1 lines. For more information, see Viewing Current T1 Statistics.

Examples

The following example displays DS1 statistics.

lsds1cursts

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

lsds1intst

List DS1 interval statistics.

lsds1intst Location Num

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

Num

A number specifying an interval, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). Values: 1-96.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays the specified interval of DS1 line performance that were gathered every 15-minutes over the past 24 hours. Fails if the interval does not exist. For more information, see Viewing Interval T1 Statistics.

Examples

The following example shows performance statistics for the DS1 line at slot 1 line 1.

lsds1intst 1.1 5

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List all DS1current statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

lsds1ln

List DS1 line information.

lsds1ln Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Valid line numbers:

  • NSC: 1-16

  • BSC: 1-168 as shown by the following table of DS1 to DS3 mappings.

DS3 Line Number DS1 Line Number

501 1-28

502 29-56

503 57-84

504 85-112

505 113-140

506 141-168

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display configuration and alarm information about a DS1 lines. For more information, seeViewing DS1/E1 Configuration and Status.

Examples

The following example lists configuration information about the DS1 line at slot 1 line 12.

lsds1ln 1.12

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List all DS1current statistics

lsds1intst

List DS1 line interval statistics

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

lsds1lns

List all DS1 lines.

lsds1lns

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the configuration and alarm information for all DS1 lines. For more information, see Viewing Summary DS1/E1 Information.

Examples

The following example displays information about all DS1 configurations and alarms.

lsds1lns

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List statistics for all DS1 lines

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

lsds1lnst

List DS1 line statistics.

lsds1lnst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the real-time statistics of the specified DS1 line. For more information, see Viewing T1 Real-Time Alarm Statistics.

Examples

The following example displays the real-time statistics of the DS1 line at slot 1 line 1.

lsds1lnst 1.1

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List statistics for all DS1 lines

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

lsds1totst

List DS1 total statistics.

lsds1totst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the totals of performance statistics of the specified DS1 line gathered over the past 24 hours. For more information, see Viewing Total T1 Statistics.

Examples

The following example shows the totals of performance statistics of the DS1 line at slot 1 line 1 over the past day.

lsds1totst 1.1

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List statistics for all DS1 lines

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 statistics

lsds1totsts

List DS1 total statistics

lslns

List existing lines

lsds1totsts

List DS1 total statistics.

lsds1totsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays totals of the performance statistics of the all DS1 lines over the past day. For more information, see Viewing Total T1 Statistics.

Examples

The following example displays statistics of DS1 lines over the past day.

lsds1totsts

Related Commands

Command Description

addds1ln

Add DS1 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

clrds1lnst

Clear DS1 line statistics

delds1ln

Delete DS1 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List statistics for all DS1 lines

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lslns

List existing lines

lsds3alm

List DS3 alarm.

lsds3alm Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card addition - no functional change

Usage Guidelines

Use this command to display the DS3 line alarm thresholds for a given line. For more information, see Viewing DS3 Alarm Thresholds.

Examples

The following example shows the alarm thresholds of the DS3 line at slot 7 line 1.

lsds3alm 7.1

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3curst

List DS3 current statistics

lsds3intst

List DS3 interval statistics

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

lsds3curst

List DS3 current statistics.

lsds3curst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card inclusion - no functional change

Usage Guidelines

Displays the performance statistics of the current 15-minute collection period for the specified DS3 line. For more information, see Viewing Current DS3 Statistics.

Examples

The following example shows the performance statistics of the DS3 line at slot 7 line 1.

lsds3curst 7.1

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3cursts

List all current DS3 statistics

lsds3intst

List DS3 interval statistics

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

lsds3cursts

List current statistics for all DS3 lines.

lsds3cursts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card inclusion - no functional change

Usage Guidelines

Use this command to display the location of the DS3, errored seconds, severely errored seconds, UAS seconds, and LCV seconds. For more information, see Viewing Current DS3 Statistics.

Examples

The following example displays DS3 statistics.

lsds3cursts

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List current DS3 line statistics

lsds3intst

List DS3 interval statistics

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

lsds3intst

List DS3 interval statistics.

lsds3intst Location Num

Syntax Description

Location

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

Num

A number specifying an interval, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). Values: 1-96.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card inclusion - no functional change

Usage Guidelines

Use this command to display one of the 96 records of DS3 line performance that were gathered every 15-minutes over the past 24 hours. For more information, see Viewing Interval DS3 Statistics.

Examples

The following example shows performance statistics for the DS3 line at slot 7 line 1.

lsds3intst 7.1 1

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List current DS3 line statistics

lsds3ln

List DS3 line

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

lsds3ln

List DS3 line and configuration.

lsds3ln Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card inclusion - no functional change

Usage Guidelines

Use this command to display configuration information about one DS3 line. For more information, see Viewing DS3 Configuration and Status.

Examples

The following lists configuration information about the DS3 line at slot 7 line 1.

lsds3ln 7.1

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List current DS3 line statistics

lsds3intst

List DS3interval statistics

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

lsds3lns

List DS3 lines.

lsds3lns

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card inclusion - no functional change

Usage Guidelines

Use this command to display the configuration information for all DS3 lines. For more information, see Viewing Summary DS3 Information.

Examples

The following example displays all DS3 line configurations.

lsds3lns

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List current DS3 line statistics

lsds3intst

List DS3 interval statistics

lsds3ln

List DS3 lines

lsds3totst

List DS3 total statistics

lsds3lnst

List real-time statistics for a DS3 line.

lsds3lnst

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card inclusion - no functional change

Usage Guidelines

Use this command to display Loss of Signal, Out Of Frame, RAI, CCV, Framing Pattern Errors, PBit Parity Errors, and Far End Block Errors. For more information, see Viewing DS3 Real-Time Alarm Statistics.

Examples

The following example displays real-time statistics for slot 14 line 501.

lsds3lnst 14.501

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List current DS3 line statistics

lsds3intst

List DS3 interval statistics

lsds3ln

List DS3 line

lsds3lns

List DS3 lines

lsds3totst

List DS3 total statistics

lsds3totst

List DS3 total statistics.

lsds3totst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS3 line.

Valid slot numbers:

BSC: 11-16

DMC: 7 or 8 (reserved for future use)

Valid line numbers:

BSC: 501-506

DMC: 1-6 (reserved for future use)

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

1.1

BSC card inclusion - no functional change

Usage Guidelines

Use this command to display the totals of performance statistics of the specified DS3 line gathered over the past 24 hours. For more information, see Viewing Total DS3 Statistics.

Examples

The following example shows the totals of performance statistics of the DS3 line at slot 7 line 1 over the past day.

lsds3totst 7.1

Related Commands

Command Description

addds3ln

Add DS3 line

chds3alm

Change DS3 line alarm

chds3ln

Change DS3 line

clrds3lnst

Clear statistics for DS3 line

delds3ln

Delete DS3 line

lsds3alm

List DS3 alarm

lsds3curst

List current DS3 line statistics

lsds3intst

List DS3interval statistics

lsds3lns

List DS3 line

lsds3ln

List DS3 lines

lsdsps

List DSP multiservice modules.

lsdsps

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list all DSP multiservice modules (MSMs) and their operational status. For more information, see Viewing MSM Configuration and Status.

Examples

The following example lists DSP MSMs.

lsdsps

Related Commands

Command Description

lsmsms

List multiservice modules

lsdurationif

List duration information about announcement files.

lsdurationif

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

You use this command to list the maximum, current, and available duration of announcement files.

Examples

The following command lists duration information about announcement files.

lsdurationif

Related Commands

Command Description

acannfile

Activate an announcement file

deacannfile

Deactivate an announcement file

rmannfile

Remove an announcement file

lsannfile

List the given announcement file

lsannfiles

List all announcement files

lse1alm

List all alarm thresholds for a E1 line.

lse1alm Location

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list E1 line alarm thresholds, such as Red, RAI, and Perf Alarm Severity. This command only applies to BSC lines. For more information, see Viewing E1 Alarm Thresholds.

Examples

The following example lists E1 alarm threshold levels for line 1 of slot 3.

lse1alm 3.1

lse1alrm

List all alarms for a E1 line.

lse1alrm Location

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list E1 line alarms, such as Red, RAI, and Perf Alarm Severity. This command only applies to BSC lines. For more information, see Viewing E1 Alarms.

Examples

The following example lists E1 alarms for line 1 of slot 3.

lse1alrm 3.1

lse1curst

List current E1 current statistics.

lse1curst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display the E1 performance statistics of the current 15-minute collection period. This command only applies to BSC lines. For more information, see Viewing Current E1 Statistics.

Examples

The following example lists E1 current statistics for line 1 of slot 3.

lse1curst 3.1

lse1cursts

List all E1 current statistics.

lse1curst

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display all E1 performance statistics for the current 15-minute collection period. This command only applies to BSC lines. For more information, see Viewing Current E1 Statistics.

Examples

The following example lists all E1 current statistics for the chassis.

lse1cursts

lse1intst

List E1 interval statistics.

lse1intst Location Num

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Num

A number specifying an interval, where 1 is the most recently completed 15 minute interval and 96 is the oldest 15 minutes interval (assuming that all 96 intervals are valid). Values: 1-96.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Displays the specified interval of E1 line performance. Interval statistics are gathered every 15-minutes over the past 24 hours. The request fails if the interval does not exist (has not been collected). This command only applies to BSC lines. For more information, see Viewing Interval E1 Statistics.

Examples

The following example lists interval 2 statistics for line 1 of slot 3.

lse1intst 3.1 2

lse1lnst

List real-time E1 line statistics.

lse1lnst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display the real-time statistics and alarms for the specified E1 line. This command only applies to BSC lines. For more information, see Viewing E1 Real-Time Alarm Statistics.

Examples

The following example lists E1 line statistics for line 1 of slot 3.

lse1lnst 3.1

lse1lnsts

List all real-time E1 line statistics.

lse1lnsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display the real-time statistics and alarms for the specified E1 line. This command only applies to BSC lines. For more information, see Viewing E1 Real-Time Alarm Statistics.

Examples

The following example lists all E1 current statistics for the chassis.

lse1lnsts

lse1perf15

List 15-minute performance alarms for an E1 line.

lse1perf15 Location

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display 15-minute performance alarms for an E1 line. This command only applies to BSC lines. For more information, see Viewing E1 Performance Alarms.

Examples

The following example lists 15-minute performance alarms for line 1 of slot 3.

lse1perf15 3.1

lse1perf24

List 24-hour performance alarms for an E1 line.

lse1perf24 Location

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display 24-hour performance alarms for an E1 line. This command only applies to BSC lines. For more information, see Viewing E1 Performance Alarms.

Examples

The following example lists 24-hour performance alarms for line 1 of slot 3.

lse1perf24 3.1

lse1totst

List total statistics.

lse1totst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the line. Valid slots: 1-8 and 11-16. Valid lines: 1-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display the totals of performance statistics gathered over the past 24 hours for the specified line. This command only applies to BSC lines. For more information, see Viewing Total E1 Statistics.

Examples

The following example lists E1 total statistics for line 1 of slot 3.

lse1totst 3.1

lse1totsts

List total statistics for all E1 lines.

lse1totsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display performance statistics totals gathered over the past 24 hours for all lines. This command only applies to BSC lines. For more information, see Viewing Total E1 Statistics.

Examples

The following example lists all total statistics for the all E1 lines.

lse1totsts

lsem

List email server.

lsem

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list email server information and source email addresses. For more information, see Listing Email Server and Email Alert Registrations.

Examples

The following example lists email service information.

lsem

Related Commands

Command Description

addereg

Add email registration

chem

Configure email registration

chereg

Change email registration

delereg

Delete email registration

lsereg

List entry registered

lseregs

List registered email alerts

lsemm

List sensor environmental monitoring data.

lsemm UnitID SensorType SensorID

Syntax Description

UnitID

The unit identifier:

1=slot1

2=slot2

3=slot3

4=slot4

5=slot5

6=slot6

7=slot7

8=slot8

9=slot9

10=slot10

11=slot11

12=slot12

13=slot13

14=slot14

15=slot15

16=slot16

100=chassis

SensorType

Temperature, fan, or voltage sensor. Values: 1 - 3, respectively. Fan (3) is valid only with the chassis unit ID (100). For more information, see "Monitoring Environmental Alarms" section

SensorID

The identifier that is usually on the top or bottom of the card, or next to the CPU. Values: an integer.

Defaults

No default behavior or values

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the specified environmental measurement taken by a single sensor. Sensors measure the following conditions: temperature of the chassis, Switch Control Card (SCC) and Narrowband Service Card (NSC); the voltage of the chassis and all cards, SCC, NSC, and Distribution Matrix Card (DMC); the fan speed of the chassis. Output is degrees Celsius for temperature, volts for chassis, percentage of voltage for card, and RPM for fan sensor. For more information, see Viewing Environmental Information.

Examples

The following example lists the voltage of the chassis.

lsemm 100 3 99923

Related Commands

Command Description

lsemms

List environmental monitoring sensors

lsemms

List environmental monitoring sensors.

lsemms

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display environmental measurements taken from all sensors in the cards and chassis: the temperature of the chassis, Switch Control Card (SCC), and NSC services module; the voltage of the chassis and all cards, SCC, Narrowband Service Card (NSC), and Distribution Matrix Card (DMC); the fan speed of the chassis. For more information, see Viewing Environmental Summary Information.

Examples

The following example lists environmental monitoring sensors.

lsemms

Related Commands

Command Description

lsemm

List sensor environmental monitoring data

lsereg

List entry registered.

lsereg Index

Syntax Description

Index

Position of the email address in the SnmpEmailRegTable. Values: integer.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Lists an entry registered for email alerts. For more information, see Listing Email Server and Email Alert Registrations.

Examples

The following example lists the email address at position 10 in the registration table.

lsereg 10

Related Commands

Command Description

addereg

Add email registration

chem

Configure email registration

chereg

Change email registration

delereg

Delete email registration

lsem

List email server

lseregs

List registered email alerts

lseregs

List registered email alerts.

lseregs

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display list all entries registered for email alerts. For more information, see Listing Email Server and Email Alert Registrations.

Examples

The following example lists entries registered for email alerts.

lsemms

Related Commands

Command Description

addereg

Add email registration

chereg

Change email registration

delereg

Delete email registration

lsem

List email server

lsereg

List registered email alert

lsethln

List Ethernet line.

lsethln Location

Syntax Description

Location

The slot and line number, delimited by a period, of the Ethernet line. Valid slots: 9 or 10. Valid lines: 1-4.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the configuration information for the Ethernet interface at the line specified. For more information, see Viewing Fast Ethernet Configuration and Status.

Examples

The following example lists Ethernet configuration at slot 9 line 1.

lsethln 9.1

Related Commands

Command Description

addethln

Add Ethernet line

chethln

Change Fast Ethernet line

delethln

Delete Ethernet line

dnethln

DeActivate Ethernet line

lsethlns

List Ethernet Lines

upethln

Activate Ethernet line

lsethlns

List Ethernet lines.

lsethlns

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the configuration information for all Ethernet interfaces. For more information, see Viewing Fast Ethernet Configuration and Status.

Examples

The following example lists Ethernet lines.

lsethlns

Related Commands

Command Description

addethln

Add Ethernet line

chethln

Change Fast Ethernet line

delethln

Delete Ethernet line

dnethln

DeActivate Ethernet line

lsethln

List Ethernet line

upethln

Activate Ethernet line

lsevt

List event log.

lsevt

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the date and time of the event, a description of the event, and active alarms. For more information, see

Examples

The following example lists the event log.

lsevt

Related Commands

Command Description

clrevt

Clear event log

lssgrp

List information for an RUDP session group.

lssgrp SetID GroupID

Syntax Description

SetID

Session set identifier. Value: integer.

GroupID

Session group identifier.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

A session group consists of one or more RUDP sessions. A session represents the 'physical' connection between the media gateway and media gateway controller. This command lists detail configuration and status information for a single session group. For more information, see Viewing Session Groups.

Examples

The following example lists information about session group 1.

lssgrp 1 2

Related Commands

Command Description

lsgroups

List detailed information for all RUDP session groups

lsgroupstat

List statistics for an RUDP session group

lssgrps

List detailed information for all RUDP session groups.

lssgrps

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

A session group consists of one or more RUDP sessions. A session represents the 'physical' connection between the media gateway and media gateway controller. This command lists summary configuration and status information for all groups. For more information, see Viewing Session Groups.

Examples

The following example lists statistics for all RUDP session groups.

lssgrps

Related Commands

Command Description

lsgroup

List information for an RUDP session group

lsgroupstat

List statistics for RUDP groups

lsgroupstat

List statistics for an RUDP session group.

lsgroupstat Index

Syntax Description

Index

Session group identifier. Use lsgroups to determine valid identifiers. Value: integer.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

A session group consists of or more RUDP sessions. A session represents the 'physical' connection between the media gateway and media gateway controller. This command lists statistics for a single session group. For more information, see Viewing Session Group Statistics.

Examples

The following example lists statistics for session group 1.

lsgroupstat 17

Related Commands

Command Description

lsgroup

List detailed information for an RUDP session group

lsgroups

List detailed information for all RUDP session groups

lsipdc

List IPDC Soft Switch configuration.

lsipdc

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list the IPDC Soft Switch configuration. For more information, see Viewing IPDC Settings.

Examples

The following example lists the IPDC Soft Switch configuration.

lsipdc

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdctimer

List IPDC Timer Configuration

lsipdccot

List IPDC COT Configuration

lsipdccot

List IPDC COT configuration.

lsipdccot

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command list the IPDC COT configuration. For more information, see Viewing IPDC COT Information.

Examples

The following example lists the IPDC COT configuration.

lsipdccot

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdctimer

List IPDC Timer Configuration

lsipdctimer

List IPDC timer configuration.

lsipdctimer

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list the IPDC timer configuration. For more information, see Viewing IPDC Timer and Retry Counter Information.

Examples

The following example lists the IPDC timer configuration.

lsipdctimer

Related Commands

Command Description

chipdcpssip

Change IPDC primary Soft Switch IP and TCP port

chipdcsssip

Change IPDC secondary Soft Switch IP and TCP port

chipdcgwip

Change IPDC gateway IP and TCP port

chipdcssid

Change IPDC system ID

chipdcsstype

Change IPDC system type

chipdcssbaynum

Change IPDC Bay Number

chipdcmaxm

Change IPDC Maximum Modules

chipdcssnumfor

Change IPDC Numbering format

chipdcssadm

Change IPDC Admin Status

chipdcsshlth

Change IPDC Health Check

chipdctimer

Change IPDC Timers

chipdccot

Change IPDC COTs

chpseudoip

Change pseudo IP address

lsipdc

List IPDC Soft Switch configuration

lsipdccot

List IPDC COT Configuration

lsiproute

List IP route

lsiproute Dest

Syntax Description

Dest

The destination IP address of this route. An entry of 0.0.0.0 is considered a default route.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list an IP route. For more information, see Viewing IP Routes.

Examples

The following example lists the IP route at 10.1.1.1:

lsiproute 10.1.1.1

Related Commands

Command Description

addiproute

Add IP route

deliproute

Delete IP route

lsiproutes

List IP routes

lsiproutes

List IP routes

lsiproutes

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list the destination, gateway (next hop), interface index, and mask of IP routes. For more information, see Viewing IP Routes.

Examples

The following example lists IP routes:

lsiproutes

Related Commands

Command Description

addiproute

Add IP route

deliproute

Delete IP route

lsiproute

List IP route

lskey

Display file key.

lskey

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the tftp security key. This key authenticates users when uploading and downloading files. For more information, see Assigning a tftp Security Key.

Examples

The following example displays the current tftp key.

lskey

Related Commands

Command Description

chkey

Change tftp key.

lslapd

List general LAPD information for a card.

lslapd Location

Syntax Description

Location

The slot number of the card. Values: 9-16.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the number of physical links, DLCs, DLCs per SAP, and ASP links. For more information, see Viewing LAPD Parameters.

Examples

The following example lists the LAPD information for the card in slot 10.

lslapd 10

Related Commands

Command Description

lslapds

List information about all LAPD cards

lslapds

List information about all LAPD cards.

lslapds

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays the card number, physical links, number of DLCs, LD links, and ASP links. For more information, see Viewing LAPD Parameters.

Examples

The following example lists information about all LAPD cards in the MGX 8260 chassis.

lslapds

Related Commands

Command Description

lslapd

List general LAPD information for a card

lslgcd

List upgrade information.

lslgcd upgdLogicalCardIndex

Syntax Description

upgdLogicalCardIndex

The logical number of the card to upgrade. Values: 1-16.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.1.3

This command was first introduced.

Usage Guidelines

Use this command to list upgrade information for a card.

Related Commands

Command Description

upgd

Upgrade the software image

upgdcancel

Gracefully cancel an upgrade

upgdcmit

Commit the new software image

lslgcds

List upgrade information for all cards

lslgcds

List upgrade information for all cards.

lslgcd

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.1.3

This command was first introduced.

Usage Guidelines

Use this command to list upgrade information for all cards.

Related Commands

Command Description

upgd

Upgrade the software image

upgdcancel

Gracefully cancel an upgrade

upgdcmit

Commit the new software image

lslgcd

List upgrade information

lslns

List all lines.

lslns

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the slot number, line number, and line type for each DS1, DS3, and Fast Ethernet line. For more information, see Viewing All MGX 8260 Lines.

Examples

The following example lists existing lines.

lslns

Related Commands

Command Description

addds1ln

Add DS1 line

addds3ln

Add DS3 line

chds1alm

Change DS1 alarm severity and thresholds

chds1ln

Change DS1 line

chds3ln

Change DS3 line

clrds1lnst

Clear DS1 line statistics

clrds3lnst

Clear statistics for DS3 line

delds1ln

Delete DS1 line

delds3ln

Delete DS3 line

lsbertds1

List DS1 BERT results

lsds1alm

List DS1 alarm thresholds

lsds1curst

List DS1 current statistics

lsds1cursts

List DS1 current statistics

lsds1intst

List DS1 interval statistics

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

lsds1lnst

List DS1 line statistics

lsds1totst

List DS1 total statistics

lsds1totsts

List DS1 total statistics

lsds3ln

List DS3 line

lsds3lns

List DS3 lines

lslogicalcarddchan

List bulk D Channel usage for a card.

lslogicalcarddchan Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line. For example, enter slot 3 line 2 as 3.2. Valid slot numbers:

  • NSC: 1-8 and 11-16

  • BSC: 11-16

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list bulk D Channel usage by card. For more information, see Viewing D Channels.

Examples

The following example lists D Channels for card 2:

lslogicalcarddchan 2

Related Commands

Command Description

lsdchan

List D Channel details for a line

lsdchans

List D Channel summaries for all lines

lslogicalcarddchans

List D Channel capacity for the chassis

lslogicalcarddchans

List D Channel capacity for the chassis.

lslogicalcarddchans

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list bulk D Channel capacity. For more information, see Viewing D Channels.

Examples

The following example lists D Channel capacity:

lslogicalcarddchans

Related Commands

Command Description

lsdchan

List D Channel details for a line

lsdchans

List D Channel summaries for all lines

lslogicalcarddchan

List D Channel bulk usage for a card

lslogin

List login information.

lslogin Index

Syntax Description

Index

The index number of the user account. Values: 1 - 20.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Displays details about a current login, including the account name, source IP address, and the date and time the session started. For more information, see Viewing Current Logins.

Examples

The following example information about the login with an index of 1.

lslogin 1

Related Commands

Command Description

lslogins

View all logins

lslogins

List all active logins.

lslogins

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Displays information about all current logins, including the account names, source IP addresses, and the date and time the sessions started. For more information, see Viewing Current Logins.

Examples

The following example information about all current logins.

lslogins

Related Commands

Command Description

lslogin

View login details

lsm13

List DS3-to-DS1 mapping.

lsm13 DS3Line DS1Line

Syntax Description

DS3Line

The number of the source DS3 line. Values: 1 - 6.

DS1Line

The number of the DS1 line, or starting DS1 line, within the DS3 line. Values: 1 - 28.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays the DS3-to-DS1 mapping. For more information, see Viewing Map Tables.

Examples

The following example displays mapping from DS1 line 3 within DS3 line 1.

lsm13 1 3

Related Commands

Command Description

addm13

Add DS3-to-DS1 mapping

chm13

Change DS1 to DS3 map

delm13

Delete DS1 to DS3 map

lsm13s

List DS3-to-DS1 mappings

lsm13s

List DS3-to-DS1 mappings.

lsm13s

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays all DS3-to-DS1 mapping. For more information, see Viewing Map Tables.

Examples

The following example displays all DS3-to-DS1 mapping.

lsm13s

Related Commands

Command Description

addm13

Add DS3-to-DS1 mapping

chm13

Change DS1 to DS3 map

delm13

Delete DS1 to DS3 map

lsm13

List a DS3-to-DS1 mapping

lsmacsapprof

List information about a MACSAP profile.

lsmacsapprof Index

Syntax Description

Index

The identifier of a MAC SAP. Values: 1 - 16.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays the interface, arbitration, LAPD type, and N202. For more information, see Viewing MACSAP Profiles.

Examples

The following example displays information about MAC SAP 3.

lsmacsapprof 3

Related Commands

Command Description

addmacsapprof

Add a MACSAP profile

delmacsapprof

Delete a MACSAP profile

lsmacsapprofs

List all MACSAP profiles

lsmacsapstat

List statistics for a MACSAP interface

lsmacsapstats

List MACSAP statistics

lsmacsapprofs

List all MACSAP profiles.

lsmacsapprofs

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list summary information about MACSAP interfaces, including the MACSAP profile number, the interface, arbitration, LAPD type, and N202. For more information, see Viewing MACSAP Profiles.

Examples

The following example lists all MACSAP profiles.

lsmacsapprofs

Related Commands

Command Description

addmacsapprof

Add a MACSAP profile

delmacsapprof

Delete a MACSAP profile

lsmacsapprof

List information about a MACSAP profile

lsmacsapstat

List statistics for a MACSAP interface

lsmacsapstats

List MACSAP statistics

lsmacsapstat

List statistics for a MACSAP interface .

lsmacsapstat Index

Syntax Description

Index

The slot and line number, delimited by a period, of the MACSAP interface.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display received frames, transmitted frames, and received bytes for a MACSAP interface. For more information, see Viewing MACSAP Statistics.

Examples

The following example displays statistics for the MACSAP at slot 14, line 1.

lsmacsapstat 14.1

Related Commands

Command Description

addmacsapprof

Add a MACSAP profile

delmacsapprof

Delete a MACSAP profile

lsmacsapprof

List information about a MACSAP profile

lsmacsapprofs

List information about all MACSAP profiles

lsmacsapstats

List MACSAP statistics

lsmacsapstats

List MACSAP statistics for all interfaces.

lsmacsapstats

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays statistics for MACSAP, including the location of each MACSAP, received frames, transmitted frames, and received bytes. For more information, see Viewing MACSAP Statistics.

Examples

The following example displays MACSAP statistics for all interfaces

lsmacsapstats

Related Commands

Command Description

addmacsapprof

Add a MACSAP profile

delmacsapprof

Delete a MACSAP profile

lsmacsapprof

List information about a MACSAP profile

lsmacsapprofs

List information about all MACSAP profiles

lsmacsapstat

List statistics for a MACSAP interface

lsmgcp

List MGCP core parameters.

lsmgcp

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the MGCP protocol parameters. For more information, see Viewing MGCP Status Information.

Examples

The following example lists MGCP core parameters.

lsmgcp

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chmgcpcore

Change MGCP core parameters

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

lsmgcpdef

List MGCP default parameters

lsmgcpdef

List MGCP default parameters.

lsmgcpdef

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays the MGCP protocol default parameters. For more information, see Viewing MGCP Settings.

Examples

The following example displays default parameters for the MGCP protocol.

lsmgcpdef

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chmgcpcore

Change MGCP core parameters

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpstat

List MGCP statistics.

lsmgcpstat

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display statistics for the MGCP protocol stack. For more information, see Viewing MGCP Protocol Statistics.

Examples

The following example lists statistics for the MGCP protocol stack.

lsmgcpstat

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chmgcpcore

Change MGCP core parameters

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

lsmgcpvoice

List MGCP voice parameters

lsmgcpvoice

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display voice parameters for the MGCP protocol. For more information, see Viewing MGCP Settings

Examples

The following example displays voice parameters for MGCP.

lsmgcpvoice

Related Commands

Command Description

chmgcplocaladdr1

Change the MGCP local address for network 1

chmgcplocaladdr2

Change the MGCP local address for network 2

chmgcpcore

Change MGCP core parameters

chmgcpvoice

Change MGCP voice parameters

chpmgcpaddr

Change the primary Media Gateway Controller addresses

chsmgcpaddr

Change the secondary Media Gateway Controller addresses

lsmgcp

List MGCP core parameters

lsmgcpdef

List MGCP default parameters

lsmgcpstat

List MGCP statistics

lsmgips

List management IP addresses.

lsmgips

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display all management IP addresses and related information. For more information, see Viewing Management Port Parameters.

Examples

The following example displays management IP addresses.

lsmgips

Related Commands

Command Description

chibip

Change in-band IP

chsysip

Change system IP

lsmpc

List MPC parameters.

lsmpc

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to list MPC parameters: the default type of network, packetization period, bandwidth, echo cancellation, silence suppression, type of service, resource reservation, and COT receive and transmit tones. For more information, see Viewing Default Call Setup Parameters.

Examples

The following example displays MPC parameters.

lsmpc

lsmsms

List multiservice modules.

lsmsms

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list all multiservice modules (MSMs) and their operational status. For more information, see Viewing MSM Configuration and Status.

Examples

The following example displays multiservice modules.

lsmsms

Related Commands

Command Description

lsdsps

List DSP multiservice modules

lsndinf

List node information.

lsndinf

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the rack number for this node, the node name and number, and the type and serial number of the back plane. For more information, see Viewing Node Parameters.

Examples

The following example displays node information.

lsndinf

Related Commands

Command Description

chndinf

Change node information

lsports

List all ports.

lsports

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display information about all ports.

Examples

The following example displays information about ports.

lsports

lsreds

List redundancy pairs.

lsreds

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display card redundancy pairs. For more information, see Viewing BSC and NSC Redundancy.

Examples

The following example lists card redundancy pairs.

lsreds

Related Commands

Command Description

addreds

Add card redundancy pairs

delreds

Delete card redundancy pairs

lsrudpconnstats

List statistics for an RUDP connection.

lsrudpconnstats ID

Syntax Description

ID

RUDP session identifier. Value: integer

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The communications link between the media gateway and media gateway controller uses a Reliable UDP connection. This command lists the connection-related statistics for one link, which includes packet transmission totals and selected connection problems. For more information, see Viewing RUDP Connection Statistics.

Examples

The following example lists statistics for an RUDP connection.

lsrudpconnstats

Related Commands

Command Description

lsgroupstat

List session group statistics

lsrudptxstats

List RUDP transport statistics

lssessstats

List session statistics

lssessstatslr

List session statistics since last reset

lsrudpgblstats

List global statistics for RUDP

lsrudpgblstats

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

The communications link between the media gateway and media gateway controller uses Reliable UDP connections. This command lists the connection statistics for all RUDP links, which include packet totals and transmission problems.

Examples

The following example lists global statistics for RUDP.

lsrudpgblstats

Related Commands

Command Description

lsrudpconnstats

List statistics for an RUDP connection

lsrudpgblstats

List global statistics for RUDP

lssession

List RUDP session information

lsset

List session set information

lsrudptxstats

List RUDP transport statistics.

lsrudptxstats SessionSetId GroupId SessionId

Syntax Description

SessionSetId

The index of the session set to which the group containing the session manager belongs. Values: 1-6.

GroupId

The index of the session group to which the session manager belongs. Values: 1 or 2.

SessionId

The index of this session. Values: 1 or 2

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list transport RUDP statistics, including RUDP connections events and transmit failures. For more information, see Viewing RUDP Transport Statistics.

Examples

The following example displays RUDP parameters for session 1 of group 1 in set 1.

lsrudptxstats 1 1 1

Related Commands

Command Description

lsgroupstat

List session group statistics

lsrudpconnstats

List RUDP connection statistics

lssessstats

List session statistics

lssessstatslr

List session statistics since last reset

lssession

List RUDP session information.

lssession SetID GroupID SessionID

Syntax Description

SetID

The session set identifier. Use lssessions to determine valid identifiers. Value: integer.

GroupID

The session group identifier. Value: integer.

SessionID

The session identifier. Value: integer

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

A session represents a 'physical' connection between the media gateway and media gateway controller. This command lists detail information for a single RUDP session. For more information, see Viewing Session Information.

Examples

The following example lists information about session 33.

lssession 1 2 3

Related Commands

Command Description

lssgrps

List session group information

lssets

List session set information

lssessions

List all RUDP sessions.

lssessions

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

A session represents a 'physical' connection between the media gateway and media gateway controller. This command lists summary information for a all RUDP sessions. For more information, see Viewing Session Information.

Examples

The following example lists all RUDP sessions.

lssessions

Related Commands

Command Description

lssession

List all RUDP session

lsset

List session set information

lssessstats

List session statistics.

lssessstats SessionSetId GroupId SessionId

Syntax Description

SessionSetId

The index of the session set to which the group containing the session manager belongs. Values: 1-6.

GroupId

The index of the session group to which the session manager belongs. Values: 1 or 2.

SessionId

The index of this session. Values: 1 or 2

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list session statistics for a specific session, such as total packets and PDU information. For more information, see Viewing Session Statistics.

The following example displays session statistics for session 1 of group 1 in set 1.

lssessstats 1 1 1

Related Commands

Command Description

lsgroupstat

List session group statistics

lsrudpconnstats

List RUDP connection statistics

lsrudptxstats

List RUDP transport statistics

lssessstatslr

List session statistics since last reset

lssessstatslr

List session statistics since last reset.

lssessstatslr SessionSetId GroupId SessionId

Syntax Description

SessionSetId

The index of the session set to which the group containing the session manager belongs. Values: 1-6.

GroupId

The index of the session group to which the session manager belongs. Values: 1 or 2.

SessionId

The index of this session. Values: 1 or 2

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list session statistics since the last reset, such as total packets and PDU information. For more information, see Viewing Session Statistics.

Examples

The following example displays session statistics for session 1 of group 1 in set 1.

lssessstatslr 1 1 1

Related Commands

Command Description

lsgroupstat

List session group statistics

lsrudpconnstats

List RUDP connection statistics

lsrudptxstats

List RUDP transport statistics

lssessstats

List session statistics

lsset

List RUDP session set information.

lsset Index

Syntax Description

Index

The session set identifier. Use lssets to determine valid identifiers. Value: integer 1-6.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

A session set is a collection of session groups, each connecting to a different media gateway controller. Use session sets for redundant media gateway controller architectures. This command lists detail information for a single RUDP session set. For more information, see Viewing Session Set Information.

Examples

The following example lists RUDP session set information.

lsset

Related Commands

Command Description

lssession

List RUDP session

lssessions

List all RUDP sessions

lssets

List all RUDP session sets.

lssets

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

A session set is a collection of session groups, each connecting to a different media gateway controller. Use session sets for redundant media gateway controller architectures. This command lists summary information for all RUDP session sets. For more information, see Viewing Session Set Information.

Examples

The following example lists all session set information.

lssets

Related Commands

Command Description

lssession

List RUDP session

lssessions

List all RUDP sessions

lsset

List RUDP session information

lsslinecst

List current statistics for a SONET line.

lsslinecst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display current ES, SES, CV, and UAS statistics for a SONET line. For more information, see Viewing Line Current Statistics.

Examples

The following example lists statistics for slot 9 line 1:

lsslinecst 9.1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsslinecsts

List current statistics for all SONET lines.

lsslinecsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display current ES, SES, CV, and UAS statistics for all SONET lines. For more information, see Viewing Line Current Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsslineist

List interval statistics for a SONET line.

lsslineist Location Interval

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Interval

The measurement interval of interest. Values: 1-96, where 1 is the most recent interval

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display interval ES, SES, CV, and UAS statistics for a SONET line. For more information, see Viewing Line Interval Statistics.

Examples

The following example lists statistics for the most recent interval of slot 9 line 1:

lsslineist 9.1 1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsslineists

List interval statistics for all SONET lines.

lsslineists

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display interval ES, SES, CV, and UAS statistics for all SONET lines. For more information, see Viewing Line Interval Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsslinetst

List total statistics for a SONET line.

lsslinetst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display total ES, SES, CV, and UAS statistics for a SONET line. For more information, see Viewing Line Total Statistics.

Examples

The following example lists statistics for slot 9 line 1:

lsslinetst 9.1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsslinetsts

List total statistics for all SONET lines.

lsslinetsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display total ES, SES, CV, and UAS statistics for all SONET lines. For more information, see Viewing Line Total Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslineist

List interval statistics for a SONET line

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lssonetalm

List SONET alarm thresholds.

lssonetalm Location

Syntax Description

Location

The slot and line number, delimited by a period, of the SONET line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display SONET alarm thresholds. For more information, see Viewing OC-3 Alarm Thresholds.

Examples

The following example lists the SONET alarm thresholds for broadband line 1.

lssonetalm 9.1

Related Commands

Command Description

addsonetln

Add a SONET line

chsonetln

Change a SONET line

delsonetln

Delete a SONET line

lssonetlns

List information about all SONET lines

lssonetalms

List alarm threshold information for all SONET lines

lssonetalms

List SONET alarms.

lssonetalms

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display to view red, yellow, and performance alarms for SONET lines. For more information, see Viewing OC-3 Alarms.

Examples

The following example lists the SONET alarms.

lssonetalms

Related Commands

Command Description

addsonetln

Add a SONET line

chsonetln

Change a SONET line

delsonetln

Delete a SONET line

lssonetlns

List information about all SONET lines

lssonetalm

List alarm information for all SONET lines

lssonetln

List SONET line.

lssonetln Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display the status and configuration information for the specified SONET line. For more information, see Viewing OC-3 Configuration and Status.

Examples

The following example lists the SONET configuration at slot 9 line 1.

lssonetln 9.1

Related Commands

Command Description

addsonetln

Add a SONET line

chsonetln

Change a SONET line

delsonetln

Delete a SONET line

lssonetlns

List information about all SONET lines

lssonetlns

List SONET lines.

lssonetlns

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display status and configuration information for all SONET lines. For more information, see Viewing OC-3 Configuration and Status

Examples

The following example lists SONET lines.

lssonetlns

Related Commands

Command Description

addsonetln

Add a SONET line

chsonetln

Change a SONET line

delsonetln

Delete a SONET line

lssonetln

List information about a SONET line

lssonetlnerdi

List SONET line extended remote defect indication.

lssonetlnerdi Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display the E-RDI (Extended Remote Defect Indication) information for the specified SONET line. For more information, see Viewing E-RDI Configuration and Status.

Examples

The following example lists the E-RDI information at slot 9 line 1.

lssonetlnerdi 9.1

Related Commands

Command Description

chsonetperdi

Change SONET path e-rdi parameters

chsonettrace

Change SONET trace parameters

chsonetexptrace

Change SONET expected trace parameters

lssonetlnerdis

List summary E-RDI information for all SONET lines

lssonetlnerdis

List E-RDI information for all lines.

lssonetlnerdis

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display E-RDI information for all SONET lines. For more information, see Viewing E-RDI Configuration and Status.

Examples

The following example lists summary E-RDI information for all lines:

lssonetlnerdis

Related Commands

Command Description

chsonetperdi

Change SONET path e-rdi parameters

chsonettrace

Change SONET trace parameters

chsonetexptrace

Change SONET expected trace parameters

lssonetlnerdi

List E-RDI information for a SONET line

lssonetstat

List SONET alarm statistics.

lssonetstat Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display SONET alarm statistics. For more information, see Monitoring SONET Alarm Statistics.

Examples

The following example lists statistics for slot 9 line 1:

lssonetstat 9.1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstats

List all SONET alarm statistics.

lssonetstats

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display all SONET alarm statistics and states. For more information, see Monitoring SONET Alarm Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsspathcst

List current statistics for a SONET path.

lsspathcst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display current ES, SES, CV, and UAS statistics for a SONET path. For more information, see Viewing Path Current Statistics.

Examples

The following example lists statistics for slot 9 line 1:

lsspathcst 9.1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsspathcsts

List current statistics for all SONET paths.

lsspathcsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display current ES, SES, CV, and UAS statistics for all SONET paths. For more information, see Viewing Path Current Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsspathist

List interval statistics for a SONET path.

lsspathist Location Interval

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Interval

The measurement interval of interest. Values: 1-96, where 1 is the most recent interval

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display interval ES, SES, CV, and UAS statistics for a SONET path. For more information, see Viewing Path Interval Statistics.

Examples

The following example lists statistics for the most recent interval of slot 9 line 1:

lsspathist 9.1 1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsspathists

List interval statistics for all SONET paths.

lsspathists

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display interval ES, SES, CV, and UAS statistics for all SONET paths. For more information, see Viewing Path Interval Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsspathtst

List total statistics for a SONET path.

lsspathtst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display total ES, SES, CV, and UAS statistics for a SONET path. For more information, see Viewing Path Total Statistics.

Examples

The following example lists statistics for slot 9 line 1:

lsspathtst 9.1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsspathtsts

List total statistics for all SONET paths.

lsspathtsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display total ES, SES, CV, and UAS statistics for all SONET paths. For more information, see Viewing Path Total Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lssrt

List static route

lssrt Address Location

Syntax Description

Address

An address in dotted notation w.x.y.z that has the last byte set to 0.

Location

The slot and line number, delimited by a period, of the origin of the static route.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the priority of the specified static route.

Examples

The following example displays the priority of the static route from slot 1 line 1 of the MGX 8260 to IP address 12.1.1.0.

lssrt 12.1.1.0 1.1

Related Commands

Command Description

addsrt

Add static route

delsrt

Delete static route

lssrts

List static routes

lssrts

List static routes.

lssrts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays information about all static routes.

Examples

The following example displays information about all static routes.

lssrts

Related Commands

Command Description

addsrt

Add static route

delsrt

Delete static route

lssrt

List static route

lsssectioncst

List current statistics for a SONET section.

lsssectioncst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display current ES, SES, SEFS, and CV statistics for a SONET section. For more information, see Viewing Section Current Statistics.

Examples

The following example lists statistics for slot 9 line 1:

lsssectioncst 9.1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsssectioncsts

List current statistics for all SONET sections.

lsssectioncsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display current ES, SES, SEFS, and CV statistics for all SONET sections. For more information, see Viewing Section Current Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsssectionist

List interval statistics for a SONET section.

lsssectionist Location Interval

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Interval

The measurement interval of interest. Values: 1-96, where 1 is the most recent interval

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display interval ES, SES, SEFS, and CV statistics for a SONET section. For more information, see Viewing Section Interval Statistics.

Examples

The following example lists statistics for the most recent interval of slot 9 line 1:

lsssectionist 9.1 1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsssectionists

List interval statistics for all SONET sections.

lsssectionists

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display interval ES, SES, SEFS, and CV statistics for all SONET sections. For more information, see Viewing Section Interval Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsssectiontst

List total statistics for a SONET section.

lsssectiontst Location

Syntax Description

Location

The slot and line number, delimited by a period, of the OC-3 line.
Valid slot: 9. Valid lines: 1-4

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display total ES, SES, SEFS, and CV statistics for a SONET section. For more information, see Viewing Section Total Statistics.

Examples

The following example lists statistics for slot 9 line 1:

lsssectiontst 9.1

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontsts

List total statistics for all SONET sections

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lsssectiontsts

List total statistics for all SONET sections.

lsssectiontsts

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

Use this command to display total ES, SES, SEFS, and CV statistics for all SONET sections. For more information, see Viewing Section Total Statistics.

Related Commands

Command Description

clrssectioncst

Clear current statistics for a SONET section

clrssectiontst

Clear total statistics for a SONET section

clrslinecst

Clear current statistics for a SONET line

clrslinetst

Clear total statistics for a SONET line

clrspathcst

Clear current statistics for a SONET path

clrspathtst

Clear total statistics for a SONET path

clrsonetstats

Clear alarm statistics for an OC-3 line

lsssectioncst

List current statistics for a SONET section

lsssectioncsts

List current statistics for all SONET sections

lsssectiontst

List total statistics for a SONET section

lsssectionist

List interval statistics for a SONET section

lsssectionists

List interval statistics for all SONET sections

lsslinecst

List current statistics for a SONET line

lsslinecsts

List current statistics for all SONET lines

lsslinetst

List total statistics for a SONET line

lsslinetsts

List total statistics for all SONET lines

lsslineist

List interval statistics for a SONET line

lsslineists

List interval statistics for all SONET lines

lsspathcst

List current statistics for a SONET path

lsspathcsts

List current statistics for all SONET paths

lsspathtst

List total statistics for a SONET path

lsspathtsts

List total statistics for all SONET paths

lsspathist

List interval statistics for a SONET path

lsspathists

List interval statistics for all SONET paths

lssonetstat

List alarm statistics for an OC-3 line

lssonetstats

List alarm statistics for all OC-3 lines

lstmgr

List trap manager.

lstmgr Addr

Syntax Description

Addr

The IP address of the manager

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays information in the trap registration list about the manager at the specified address. For more information, see Viewing SNMP Trap Registrations.

Examples

The following example lists information about the SNMP manager at 10.1.1.1.

lstmgr 10.1.1.1

Related Commands

Command Description

addtmgr

Add trap manager

clrtraps

Clear traps

delcms

Delete community string

lscms

List community string

lscmss

List community strings

lstmgrs

List trap managers

lstmgrs

List trap managers.

lstmgrs

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display information about all managers in the trap registration list. For more information, see Viewing SNMP Trap Registrations.

Examples

The following example lists trap managers.

lstmgrs

Related Commands

Command Description

addtmgr

Add trap manager

clrtraps

Clear traps

delcms

Delete community string

lscms

List community string

lscmss

List community strings

lstmgr

List trap manager

lstraps

List the trap log.

lstraps

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the date and time of each trap and alarms associated with them.

Examples

The following example displays information about all traps.

lstraps

Related Commands

Command Description

addtmgr

Add trap manager

clrtraps

Clear traps

delcms

Delete community string

lscms

List community string

lscmss

List community strings

lstmgr

List trap manager

lsusp

List a user profile.

lsusp Index

Syntax Description

Index

A userProfileTable index number. Values: 1 - 20.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list the specified user profile by index. To determine the index, use lsusps. For more information, see Viewing User Profiles.

Examples

The following example displays the profile for the user at index 3 in the user profile table. The profile includes the user's security level.

lsusp 3

Related Commands

Command Description

addusp

Add user profile

delusp

Delete user profile

lsusps

List all user profiles

lsusps

List all user profiles.

lsusps

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list the user identifier and security level for all user profiles. For more information, see Viewing User Profiles.

Examples

The following example lists all user profiles.

lsusps

Related Commands

Command Description

addusp

Add user profile

delusp

Delete user profile

lsusp

List a user profiles

lsvport

List voice port

lsusp Slot Port

Syntax Description

Slot

The logical slot number of an NSC

Port

The logical port number

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Displays information about the specified voice port.

Examples

The following example displays information about the voice port at slot 1, port 3.

lsvport 1 3

Related Commands

Command Description

addvport

Add voice port

chvport

Change voice port

delvport

Delete voice port

lsvports

List voice ports

lsvports

List voice ports

lsvports

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 5

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to list information about all voice ports.

Examples

The following example lists information about all voice ports.

lsvports

Related Commands

Command Description

addvport

Add voice port

chvport

Change voice port

delvport

Delete voice port

lsvport

List voice port

offbertds1

Stop BERT on DS1.

offbertds1 Location

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to stop the BERT on the specified DS1 line.

Examples

The following example stops a BERT that is running on the DS1 line at slot 1 line 1.

offbertds1 1.1

Related Commands

Command Description

lsbertds1

List DS1 BERT results

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

onbertds1

Start BERT on DS1

onbertds1

Start BERT on DS1.

onbertds1 Location Pattern Rate DS0 StateCtrl

Syntax Description

Location

The slot and line number, delimited by a period, of the DS1 line.

Pattern

One of the following patterns. Values: 1-13.

1 = Randomly-generated 29 -1 pattern

2 = Randomly-generated 211 -1 pattern

3 = Randomly-generated 215 -1 pattern

4 = Randomly-generated 220 -1 pattern with QRSS

5 = Randomly-generated 220 -1 pattern

6 = Randomly-generated 223 -1 pattern

7 = Repetitively-generated all-1 pattern

8 = Repetitively-generated all-1 pattern

9 = Repetitively-generated alternating 1 and 0 pattern

10 = Repetitively-generated alternating 11 and 00 pattern

11 = Repetitively-generated 1 in 24 pattern

12 = Repetitively-generated 1 in 16 pattern

13 = Repetitively-generated 1 in 8 pattern

Rate

The error rate to be injected into the pattern during BERT test. The value is used as the exponent in the formula, BER 10-x. For example, if x = 1, the error rate is 10-1 or 10%. If the rate is 0, no error is injected in the BERT pattern. Values: 1-8 as follows:

1=No Error Rate Injection.

2=0.1

3=0.01

4=0.001

5=0.0001

6=0.00001

7=0.000001

8=0.0000001

Ds0

A bit-mask specifying which DS0s are going to participate in the Bert test.

StateCtrl

A integer to control starting and stopping the Bert test. Values:

1=Start Bert test.

2=Stop Bert test.

Defaults

No default behavior or values.

Command Modes

Security level 3

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to start the BERT on the specified DS1 line. To specify which DS0s participate in a Bert test, use the Ds0 parameter. For example, 0000000000110101 specifies that the DS0 number 1, 3, 5 and 6 are participating. Convert this binary number to a decimal number and then enter that number on this option. For example, binary 0000000000110101 equals 53 decimal. Enter 53 for this option in this example

Examples

The following example starts a BERT of the DS1 line at slot 1 line 1, using the 11 00 test pattern a test rate of 10%.

onbertds1 1.1 10 1

Related Commands

Command Description

lsbertds1

List DS1 BERT results

lsds1ln

List DS1 line

lsds1lns

List DS1 lines

offbertds1

Stop BERT on DS1

rmannfile

Remove an announcement file.

rmannfile fid

Syntax Description

fid

The announcement file ID. Values: 1-100

Defaults

No default behavior or values

Command Modes

Security level

Command History

Release Modification

1.2

This command was first introduced.

Usage Guidelines

You use this command to remove an announcement file. Before attempting to remove an announcement file, first deactivate the file; otherwise, removal fails. To view file ID numbers, use the lsannfiles command.

Examples

The first command deactivates file 25, and the next command removes the file.

rmannfile 25

Related Commands

Command Description

acannfile

Activate an announcement file

deacannfile

Deactivate an announcement file

lsannfiles

List all announcement files

lsannfile

List the given announcement file

lsdurationif

List duration information about announcement files.

resetcd

Reset card.

resetcd Card

Syntax Description

Card

The number of the card to reset

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to specify a card to reset.

Examples

The following example resets card 1.

resetcd 1

Related Commands

Command Description

lscd

List information about a card

lscds

List information about all cards

resetnd

Reset node, including all processor and service modules.

resetnd

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to reset the node.

Examples

The following example resets the node.

resetnd

Related Commands

Command Description

clrndcnf

Clear node configuration

swcd

Switch to redundant NSC.

swcd Card

Syntax Description

Card

The slot number of active card to switch for the standby redundant card

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to switch between the active and standby cards of a redundant pair.

Examples

The following example makes the card in slot 1 the standby instead of the active card in a redundant pair.

swcd 1

Related Commands

Command Description

addreds

Add a card redundancy pair

delreds

Delete a card redundancy pair

lsreds

List redundancies

swclk

Switch clock.

swclk

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 2

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to switch from the current clock source to the standby clock source.

Examples

The following example switches to the standby clock.

swclk

Related Commands

Command Description

chpclksrc

Change primary clock source

chsclksrc

Change secondary clock source

lsclksrcs

List clock sources

upethln

Activate Ethernet line.

upethln Location

Syntax Description

Location

The slot and line number, delimited by a period, of the Ethernet line

Defaults

No default behavior or values.

Command Modes

Security level 4

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to bring up an Ethernet interface.

Examples

The following example brings up the Ethernet interface at slot 9 line 1, address 10.1.2.10.

upethln 9.1

Related Commands

Command Description

addethln

Add Ethernet line

chethln

Change Fast Ethernet line

delethln

Delete Ethernet line

dnethln

DeActivate Ethernet line

lsethln

List Ethernet line

lsethlns

List Ethernet Lines

upgd

Upgrade the software image.

upgd upgdLogicalCardIndex upgdFileName

Syntax Description

upgdLogicalCardIndex

The logical number of the card to upgrade. Values: 1-16.

upgdFileName

The file name of the upgrade image. Values:

SCC image: SCC_<9-character string>.fw

NSC image: NSC_<9-character string>.fw

BSC image: BSC_<9-character string>.fw

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.1.3

This command was first introduced.

Usage Guidelines

Use this command to upgrade the software image. The system sends a confirmation message on successful completion.

Examples

The following example upgrades the software image of the SCC in logical slot 9:

upgd 9 SCC_r01.01.03.fw

Related Commands

Command Description

upgdcancel

Gracefully cancel an upgrade

upgdcmit

Commit the new software image

lslgcd

List upgrade information

lslgcds

List upgrade information for all cards

upgdcancel

Cancel a software image upgrade.

upgdcancel upgdLogicalCardIndex

Syntax Description

upgdLogicalCardIndex

The logical number of the card to upgrade. Values: 1-16.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.1.3

This command was first introduced.

Usage Guidelines

Use this command to gracefully cancel a software image upgrade in a redundant system. The system sends a confirmation message on successful cancellation.

Examples

The following example cancels the software upgrade of the SCC in logical slot 9:

upgdcancel 9

Related Commands

Command Description

upgd

Upgrade the software image

upgdcmit

Commit the new software image

lslgcd

List upgrade information

lslgcds

List upgrade information for all cards

upgdcmit

Commit the new software image.

upgdcmit upgdLogicalCardIndex

Syntax Description

upgdLogicalCardIndex

The logical number of the card to upgrade. Values: 1-16.

Defaults

No default behavior or values.

Command Modes

Security level 1

Command History

Release Modification

1.1.3

This command was first introduced.

Usage Guidelines

Use this command to commit the new software image. The system sends a confirmation message on successful completion.

Examples

The following example commits the software upgrade of the SCC in logical slot 9:

upgdcmit 9

Related Commands

Command Description

upgd

Upgrade the software image

upgdcancel

Gracefully cancel an upgrade

lslgcd

List upgrade information

lslgcds

List upgrade information for all cards

version

Show the software version.

version

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to display the version information about the MGX 8260 Media Gateway.

Examples

The following example displays the software version.

version

whoami

List the name of the user who is currently logged in.

whoami

Syntax Description

The command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Security level 6

Command History

Release Modification

1.0

This command was first introduced.

Usage Guidelines

Use this command to determine who is logged in.

Examples

The following example displays the name of the user who is logged in.

whoami


hometocprevnextglossaryfeedbacksearchhelp
Posted: Sun Sep 29 05:32:55 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.