Cisco 6400 Feature Map

Cisco IOS Releases 12.1(4)DB, 12.1(4)DC, and Earlier Releases

This document provides a list of features supported by the Cisco 6400 carrier-class broadband aggregator in Cisco IOS Releases 12.1(4)DB, 12.1(4)DC, and earlier releases. For feature lists of later releases, see the "Supported Features" chapter of the Cisco 6400 Feature Guide specific to your release.

This document also provides hyperlinks to publications that include feature information and configuration examples. The publication names are in italics. When applicable, the path to the most useful section of the publication is provided in an indented list after the publication name. The listed items can be book part titles, chapter titles, section names, or subsection names.

The Cisco 6400 features are categorized as follows:

NRP Features

As of Cisco IOS Release 12.1(4)DC, the Cisco 6400 supports two node route processors (NRPs), designated as NRP-1 and NRP-2:

  • NRP-1—Incorporates a 100-Mbps Fast Ethernet interface for connecting into an IP network and has processing capability for OC-3 rate of user traffic.
  • NRP-2—Provides a Gigabit Ethernet interface and sufficient processing capability for handling OC-12 rate of user traffic.

If the "Introduced" column only lists one type of NRP, then that feature is not supported or not applicable to the excluded NRP type as of 12.1(4)DC.

Access Protocols


Feature Hyperlink & Location Introduced

Integrated Routing and Bridging (IRB)
DSL Architecture: Reliablility Design Plan:
DSL Network Architectures
Integrated Routing and Bridging (IRB)/RFC 1483 Bridging
 
Cisco IOS Bridging and IBM Networking Configuration Guide, Release 12.1:
Bridging
Cisco IOS Release 12.0 Bridging and IBM Networking Configuration Guide:
Bridging

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Multilink PPP (MLP)

Cisco IOS Dial Services Configuration Guide: Terminal Services, Release 12.1:
PPP Configuration
Configuring Media-Independent PPP and Multilink PPP

12.1(3)DC
on NRP-1

12.1(4)DC
on NRP-2

PPP IPCP Subnet Negotiation
Cisco IOS Dial Services Configuration Guide: Terminal Services, Release 12.1:
PPP Configuration
Configuring Asynchronous SLIP and PPP
Configuring Network-Layer Protocols over PPP and SLIP
Cisco IOS Release 12.0 Dial Solutions Configuration Guide:
Configuring Asynchronous PPP and SLIP
Configure Network-Layer Protocols over PPP and SLIP

IPCP Subnet Mask Support Enhancements, 12.1(3)DC feature module

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

PPP over ATM (PPPoA) terminated
Cisco IOS Wide-Area Networking Configuration Guide, Release 12.1:
Configuring ATM
Configuring PPP over ATM
Cisco IOS Release 12.0 Wide-Area Networking Configuration Guide:
Configuring ATM
Configure PPP over ATM

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

PPP over Ethernet (PPPoE) terminated

PPP over Ethernet, 12.0(3)DC feature module

PPPoE on ATM, 12.1(1)T feature module

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

PPP autosense (SNAP) PPP Autosense, 12.1(1)DC feature module

12.1(1)DC
on NRP-1

Routed Bridge Encapsulation (RBE)

ATM Routed Bridge Encaps, 12.0(5)DC feature module

DSL Architecture: Reliablility Design Plan:
DSL Network Architectures
Routed Bridge Encapsulation (RBE)

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

RBE Subinterface Grouping ATM PVC Range and Routed Bridge Encapsulation Subinterface Grouping, 12.1(5)T feature module

12.1(4)DC
on NRP-1

12.1(4)DC
on NRP-2

RBE unnumbered DHCP

 
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Addressing and Services
Configuring DHCP

ATM Routed Bridge Encaps, 12.0(5)DC feature module

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2

RBE with DHCP

Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Addressing and Services
Configuring DHCP

ATM Routed Bridge Encaps, 12.0(5)DC feature module

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

RFC 1483 bridging
DSL Architecture: Reliablility Design Plan:
DSL Network Architectures
Integrated Routing and Bridging (IRB)/RFC 1483 Bridging
 
Cisco IOS Bridging and IBM Networking Configuration Guide, Release 12.1:
Bridging
Cisco IOS Release 12.0 Bridging and IBM Networking Configuration Guide:
Bridging
Cisco 6400 NRP Configuration and Troubleshooting, white paper

Basic PVC Configuration Using Bridged RFC 1483, sample configuration

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

RFC 1483 routing
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Routing Protocols
 
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols

Cisco 6400 NRP Configuration and Troubleshooting, white paper

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

VC Traffic Shaping
Cisco 6400 Software Setup Guide:
Basic NRP Configuration
Configuring PVC Traffic Shaping
 12.0(3)DC
on NRP-1

 

Aggregation and Virtual Private Networks (VPNs)


Feature Hyperlink & Location Introduced
L2TP Multi-Hop

Multihop VPDN, 11.3(3)T feature module

Configuring L2TP Multihop to Perform Several Hops from the NAS to the LNS, Sample Configuration

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2

L2TP tunnel service
authorization enhancement		 L2TP Tunnel Service Authorization Enhancements, 12.1(1)DC feature module

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2

L2TP tunnel sharing L2TP Tunnel Management Enhancements, 12.1(1)DC feature module

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2

L2TP tunnel switching L2TP Tunnel Switching, 12.1(1)DC feature module

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2

MPLS Edge Label Switch
Router (Edge LSR)
Configuring Multiprotocol Label Switching on the Cisco 6400 UAC, configuration note:
Configuring the Node Route Processor as an MPLS Edge Label Switch Router
 12.0(7)DC
on NRP-1
MPLS Label Switch
Controller (LSC) for BPX

MPLS Label Switch Controller Enhancements, 12.1(3)T feature module

MPLS Label Switch Controller Enhancements, 12.0(7)DC feature module

Cisco IOS Switching Services Configuration Guide, Release 12.1:
Multiprotocol Label Switching
 12.0(7)DC
on NRP-1
MPLS VPNs
Configuring Multiprotocol Label Switching on the Cisco 6400 UAC, configuration note:
Configuring MPLS Virtual Private Networks
Cisco IOS Switching Services Configuration Guide, Release 12.1:
Multiprotocol Label Switching
 12.0(7)DC
on NRP-1
PPPoA tunneled into L2TP
Cisco IOS Dial Services Configuration Guide: Network Services, Release 12.1:
Virtual Private Networks
Configuring Virtual Private Networks
 
Layer 2 Tunnel Protocol, 12.0(1)T feature module

Layer 2 Tunneling Protocol, fact sheet

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

PPPoE tunneled into L2TP
Cisco IOS Dial Services Configuration Guide: Network Services, Release 12.1:
Virtual Private Networks
Configuring Virtual Private Networks
 
Layer 2 Tunnel Protocol, 12.0(1)T feature module

Layer 2 Tunneling Protocol, fact sheet

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

RFC 1577
Cisco IOS Wide-Area Networking Configuration Guide, Release 12.1:
Configuring ATM
Configuring Classical IP and ARP over ATM
Cisco IOS Release 12.0 Wide-Area Networking Configuration Guide:
Configuring ATM
Configure Classical IP and ARP over ATM

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

VLAN (ISL) on NRP
Cisco IOS Switching Services Configuration Guide, Release 12.1:
Virtual LANs
Configuring Routing Between VLANs with Inter-Switch Link Encapsulation
Cisco IOS Release 12.0 Switching Services Configuration Guide:
Virtual LANs
Configuring Routing between VLANs with ISL Encapsulation

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

 

Configuration and Monitoring


Feature Hyperlink & Location Introduced
ATM PVC Range Command

ATM PVC Range and Routed Bridge Encapsulation Subinterface Grouping, 12.1(5)T feature module

12.1(4)DC
on NRP-1

12.1(4)DC
on NRP-2

Per VC error display Per VC Error Display, 12.1(3)DC feature module

12.1(3)DC
on NRP-1

 

Hardware Support


Feature Hyperlink & Location Introduced
ATM (OC-3, OC-12, DS3) Interfaces
Cisco 6400 Software Setup Guide:
Node Line Card Interface Configuration

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

FE Interface: 10/100 auto-negotiation, auto-sensing
Cisco IOS Interface Configuration Guide, Release 12.1:
Configuring LAN Interfaces
Configuring an Ethernet or Fast Ethernet Interface
Cisco IOS Release 12.0 Interface Configuration Guide:
Configuring LAN Interfaces
Configure an Ethernet or Fast Ethernet Interface

12.0(3)DC
on NRP-1

Network Management Ethernet (NME)
Cisco 6400 Software Setup Guide:
Basic NSP Configuration
Network Management Ethernet Interface
Enabling NME Consolidation on the NRP

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

NRP 1+1 Redundancy
Cisco 6400 Software Setup Guide:
Redundancy and SONET APS Configuration
NRP Redundancy
 12.0(3)DC
on NRP-1

 

IP and Routing


Feature Hyperlink & Location Introduced
Address Resolution Protocol (ARP)
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Addressing and Services
Configuring IP Addressing
Configuring Address Resolution Methods
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Addressing and Services
Configuring IP Addressing
Configure Address Resolution Methods

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Border Gateway Protocol version 4 (BGP4)
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Routing Protocols
Configuring BGP
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring BGP

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Enhanced Interior Gateway Routing Protocol (EIGRP)
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Routing Protocols
Configuring IP Enhanced IGRP
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring IP Enhanced IGRP

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Generic routing encapsulation (GRE)
Cisco IOS Interface Configuration Guide, Release 12.1:
Configuring Logical Interfaces
Configuring a Tunnel Interface
Cisco IOS Release 12.0 Interface Configuration Guide:
Configuring Logical Interfaces
Configure a Tunnel Interface

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Internet Group Management Protocol (IGMP)
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Multicast
Configuring IP Multicast Routing
Configuring IGMP Features
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring IP Multicast Routing
Configure IGMP Features

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Internet Protocol (IP) forwarding
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Addressing and Services
Configuring IP Services
Internetworking Technology Overview:
Internet Protocols

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

IP multicast
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Multicast
Configuring IP Multicast Routing
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring IP Multicast Routing

Internet Protocol (IP) Multicast Technology Overview, white paper

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Intermediate System-to-Intermediate System (IS-IS)
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Routing Protocols
Configuring Integrated IS-IS
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring Integrated IS-IS

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Network Address Translation (NAT) support for NetMeeting Directory
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Addressing and Services
Configuring IP Addressing
Configuring Network Address Translation

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2

Open Shortest Path First (OSPF)
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Routing Protocols
Configuring OSPF
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring OSPF

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

PIM Dense Mode & Sparse Mode
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Multicast
Configuring IP Multicast Routing
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring IP Multicast Routing

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Routing Information Protocol (RIP)/RIP v2
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Routing Protocols
Configuring Routing Information Protocol
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring RIP

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Transmission Control Protocol (TCP)
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Overview
IP
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Overview
IP

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Telnet
Cisco IOS Dial Services Configuration Guide: Terminal Services, Release 12.1:
Terminal Service Configuration
Configuring Dial-In Terminal Services
Configuring Telnet and rlogin
 
Cisco IOS Release 12.0 Dial Solutions Configuration Guide:
Configuring Dial-In Terminal Services
Configure Telnet and UNIX Rlogin

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Trivial File Transfer Protocol (TFTP)
Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1:
Cisco IOS File Management
Configuring Additional File Transfer Functions
Configuring a Router as a Server
Cisco IOS Release 12.0 Configuration Fundamentals Configuration Guide:
File Management
Configuring Additional File Transfer Functions
Configure a Router as a Server
 

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Transparent Bridging
 
Cisco IOS Bridging and IBM Networking Configuration Guide, Release 12.1:
Bridging
Configuring Transparent Bridging
Cisco IOS Release 12.0 Bridging and IBM Networking Configuration Guide:
Bridging
Configuring Transparent Bridging

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

User Datagram Protocol (UDP)
Internetworking Technology Overview:
Internet Protocols
User Datagram Protocol (UDP)

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Web Cache Coordination Protocol (WCCP) version 1
Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1:
Cisco IOS System Management
Configuring Web Cache Services Using WCCP
Cisco IOS Release 12.0 Configuration Fundamentals Configuration Guide:
Cisco IOS User Interfaces
Using the Cisco Web Browser
Configure the Web Cache Control Protocol

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

WCCP (v2)
Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1:
Cisco IOS System Management
Configuring Web Cache Services Using WCCP

Web Cache Communication Protocol v2, 12.0(3)T feature module

12.0(7)DC
on NRP-1

12.1(4)DC
on NRP-2

 

Network Management


Feature Hyperlink & Location Introduced
SNMP (v1, v2, and v3)
Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1:
Cisco IOS System Management
Configuring SNMP Support
Cisco IOS Release 12.0 Configuration Fundamentals Configuration Guide:
 
System Management
Monitoring the Router and Network
Configure SNMP Support

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SNMPv3 Proxy Forwarder
Cisco 6400 Software Setup Guide:
SNMP, RMON, and Alarm Configuration
Using the NSP as the SNMPv3 Proxy Forwarder for the NRP-2
 12.1(4)DC
on NRP-2

 

RADIUS/AAA


Feature Hyperlink & Location Introduced
Password Authentication Protocol (PAP)/
Challenge Handshake Authentication Protocol
(CHAP)
Cisco IOS Security Configuration Guide, Release 12.1:
Authentication, Authorization, and Accounting (AAA)
Configuring Authentication
Non-AAA Authentication Methods
Enabling CHAP or PAP Authentication
Cisco IOS Release 12.0 Security Configuration Guide:
Authentication, Authorization, and Accounting (AAA)
Configuring Authentication
Non-AAA Authentication Methods
Enable CHAP or PAP Authentication

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Remote Authentication Dial-In User Service
(RADIUS)
Cisco IOS Security Configuration Guide, Release 12.1:
Security Server Protocols
Configuring RADIUS
Cisco IOS Release 12.0 Security Configuration Guide:
Security Server Protocols
Configuring RADIUS

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

RADIUS Attribute 8 (Framed-IP-Address) in
Access Requests (IP Hint)

RADIUS Attribute 8 (Framed-IP-Address) in Access Requests, 12.1(5)T feature module

RADIUS Attribute 8 (Framed-IP-Address) in Access Requests, 12.1(3)DC feature module

12.1(3)DC
on NRP-1

12.1(4)DC
on NRP-2

Terminal Access Controller Access Control
System Plus (TACACS+) (admin login only)
Cisco IOS Security Configuration Guide, Release 12.1:
Security Server Protocols
Configuring TACACS+
Cisco IOS Release 12.0 Security Configuration Guide:
Security Server Protocols
Configuring TACACS+

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

VPI/VCI RADIUS Request and RADIUS
Accounting for PPPoA

RADIUS VC Logging Enhancement, 12.0(7)DC feature module

RADIUS VC Logging, 11.3(9)DB and 12.0(5)DC feature module

12.0(5)DC
on NRP-1
VPI/VCI in RADIUS Request and RADIUS
Accounting for PPPoE

RADIUS VC Logging Enhancement, 12.0(7)DC feature module

RADIUS VC Logging, 11.3(9)DB and 12.0(5)DC feature module

12.1(1)DC
on NRP-1

 

Scalability and Performance


Feature Hyperlink & Location Introduced
GRE Cisco express forwarding (CEF)
Cisco IOS Switching Services Configuration Guide, Release 12.1:
Cisco Express Forwarding
Cisco IOS Interface Configuration Guide, Release 12.1:
Configuring Logical Interfaces
Configuring a Tunnel Interface

12.1(1)DC
on NRP-1
LAC CEF switching
Cisco IOS Switching Services Configuration Guide, Release 12.1:
Cisco Express Forwarding
Layer 2 Tunnel Protocol, 12.0(1)T feature module

Layer 2 Tunneling Protocol, fact sheet

12.1(3)DC
on NRP-1

12.1(4)DC
on NRP-2
L2TP sessions per tunnel limiting L2TP Tunnel Management Enhancements, 12.1(1)DC feature module

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2
NAT CEF switching
Cisco IOS Switching Services Configuration Guide, Release 12.1:
Cisco Express Forwarding
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Addressing and Services
Configuring IP Addressing
Configuring Network Address Translation

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2
Per VC buffer management
Cisco 6400 Software Setup Guide:
Basic NRP Configuration
NRP-1 Configuration
Segmentation and Reassembly Buffer Management

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2
PPPoA CEF
Cisco IOS Wide-Area Networking Configuration Guide, Release 12.1:
Configuring ATM
Configuring PPP over ATM
Cisco IOS Switching Services Configuration Guide, Release 12.1:
Cisco Express Forwarding

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2
PPPoE Fast Switching for Multicast
Cisco IOS Dial Services Configuration Guide: Terminal Services, Release 12.1:
PPP Configuration
Configuring Asynchronous SLIP and PPP
Enabling Fast Switching

12.1(1)DC
on NRP-1

 

Service Selection Gateway (NRP-SSG)


Feature Hyperlink & Location Introduced
PPP Termination and Aggregation
Multi-Domain (PTA-MD)
Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module:
Benefits
Multiple Traffic-Type Support
PPP Termination Aggregation (PTA) and PTA Multi-Domain (PTA-MD)

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

RADIUS Interim Accounting
Node Route Processor—Service Selection Gateway Enhancements, 12.0(5)DC feature module:
Configuring RADIUS Interim Accounting

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG Automatic Service Logon
Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module:
Configuring RADIUS Profiles
Account-Info Attributes
Auto Service

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG CEF Switching
Node Route Processor—Service Selection Gateway Enhancements, 12.0(5)DC feature module:
Configuring Cisco Express Forwarding

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG Default Network
Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module:
Configuring a Default Network

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG DNS Fault Tolerance
Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module:
Configuring RADIUS Profiles
Service-Info Attributes
DNS Server Address

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG enable (default is disabled)
Node Route Processor—Service Selection Gateway Enhancements II, 12.0(7)DC feature module:
Enabling NRP-SSG

12.0(7)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG full username RADIUS
attribute
Node Route Processor—Service Selection Gateway Enhancements IV, 12.1(3)DC feature module
:
Configuring the Proxy RADIUS Enhancements
Full Username Attribute

12.1(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG Cisco IOS NAT support
Node Route Processor—Service Selection Gateway Enhancements, 12.0(5)DC feature module:
Debug Commands
debug ssg data-nat

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG Local Forwarding
Node Route Processor—Service Selection Gateway Enhancements III, 12.1(1)DC feature module
:
Configuring Local Forwarding

12.1(1)DC
on NRP-1
SSG Passthrough and Proxy
Service
Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module:
Configuring RADIUS Profiles
Service-Info Attributes
Type of Service

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG Sequential and Concurrent
Service
Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module:
Configuring RADIUS Profiles
Service-Info Attributes
Service Mode

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG Service Defined Cookie
Node Route Processor—Service Selection Gateway Enhancements IV, 12.1(3)DC feature module
:
Configuring the Proxy RADIUS Enhancements
Service-Defined Cookie

12.1(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG single host logon
Node Route Processor—Service Selection Gateway Enhancements IV, 12.1(3)DC feature module:
Benefits

12.1(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG with GRE

Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module

Cisco IOS Interface Configuration Guide, Release 12.1:
Configuring Logical Interfaces
Configuring a Tunnel Interface
Cisco IOS Release 12.0 Interface Configuration Guide:
Configuring Logical Interfaces
Configure a Tunnel Interfac

12.0(3)DC
on NRP-1

 
SSG with Multicast
Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module:
Configuring Multicast
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Multicast
Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1:
IP Routing Protocols
Configuring IP Multicast Routing

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

SSG with L2TP Service Type
Node Route Processor—Service Selection Gateway Enhancements II, 12.0(7)DC feature module:
Configuring the RADIUS Profiles for NRP-SSG Support of L2TP

12.0(7)DC
on NRP-1

12.1(4)DC
on NRP-2

VPI/VCI Static binding to a
Service Profile
Node Route Processor—Service Selection Gateway Enhancements, 12.0(5)DC feature module:
Configuring VPI/VCI Indexing to Service Profile

12.0(5)DC
on NRP-1

12.1(4)DC
on NRP-2

WebSelection

Node Route Processor—Service Selection Gateway, 12.0(3)DC feature module

Cisco Service Selection Dashboard documentation

12.0(3)DC
on NRP-1

12.1(4)DC
on NRP-2

 

Other Features and Feature Enhancements


Feature Hyperlink & Location Introduced
Segmentation and Reassembly Buffer Management Enhancements

Segmentation and Reassembly Buffer Management Enhancements, 12.1(1)DC feature module

12.1(1)DC
on NRP-1
Session Scalability Enhancements

Session Scalability Enhancements, 12.1(1)DC feature module

Layer 2 Tunnel Protocol Scalability Enhancements, 12.0(7)DC feature module

12.1(1)DC
on NRP-1

12.1(4)DC
on NRP-2

 

NSP Features

ATM Connections


Feature Hyperlink & Location Introduced
F4 and F5 Operation, administration, and maintenance (OAM) cell segment and end-to-end flows
ATM Switch Router Software Configuration Guide:
Configuring Operation, Administration, and Maintenance

12.0(1)DB
on NSP
Hierarchical virtual private (VP) tunnels
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
Configuring VP Tunnels
Configuring a Hierarchical VP Tunnel for Multiple Service Categories
 12.0(4)DB
on NSP
Logical multicast support (up to 254 leaves per output port, per point-to-multipoint virtual circuits [VCs])
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
Configuring Point-to-Multipoint PVC Connections
 12.0(1)DB
on NSP
Multipoint-to-point User-Network Interface (UNI) signaling
Cisco 6400 Software Setup Guide:
Node Line Card Interface Configuration
ATM Interface Types
User-Network Interfaces
 12.0(1)DB
on NSP
Point-to-Point and Point-to-Multipoint VCs
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
12.0(1)DB
on NSP
Permanent virtual circuit (PVC), Soft PVC, Soft permanent virtual path (PVP), and switched virtual circuit (SVC)
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
12.0(1)DB
on NSP
Soft virtual channel connections (VCCs) and virtual path connections (VPCs)
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
12.0(1)DB
on NSP
VC Merge
ATM Switch Router Software Configuration Guide:
Configuring Tag Switching
Configuring VC Merge
 12.0(4)DB
on NSP
VP and VC switching
Cisco 6400 Software Setup Guide:
Basic NSP Configuration
Internal Cross-Connections
 12.0(4)DB
on NSP
VP multiplexing Understanding VP Tunnels and VP Switching, tech note 12.0(4)DB
on NSP
VP tunneling
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
Configuring VP Tunnels
 12.0(1)DB
on NSP

 

ATM Internetworking


Feature Hyperlink & Location Introduced
LAN Emulation Server (LES) and LAN Emulation Configuration Server (LECS)
ATM Switch Router Software Configuration Guide:
Configuring LAN Emulation

12.0(1)DB
on NSP
RFC 1577 (Classical IP over ATM) ATM Address Resolution Protocol (ARP) server/client
ATM Switch Router Software Configuration Guide:
Configuring IP over ATM
Configuring Classical IP over ATM
 12.0(1)DB
on NSP

 

ATM Per-Flow Queuing


Feature Hyperlink & Location Introduced
Dual leaky bucket policing (ITU-T I.371and ATM Forum UNI specifications)
Guide to ATM Technology:
Traffic and Resource Management
UPC—Traffic Policing at a Network Boundary
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Processor Feature Card Functionality
(The NSP uses the FC-PFQ feature card.)

12.0(1)DB
on NSP
Intelligent early packet discard (EPD)
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Physical Interfaces
Configuring the Interface Queue Thresholds per Service Category
ATM Switch Router Command Reference:
ATM Commands
atm output-threshold

LightStream 1010 Switch Architecture and Traffic Management, white paper

 12.0(4)DB
on NSP
Intelligent partial (tail) packet discard
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Physical Interfaces
Configuring the Interface Queue Thresholds per Service Category

LightStream 1010 Switch Architecture and Traffic Management, white paper

 12.0(4)DB
on NSP
Multiple, weighted (dynamic) thresholds for selective packet marking and discard
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Processor Feature Card Functionality
(The NSP uses the FC-PFQ feature card.)
 12.0(1)DB
on NSP
Per-VC or per-VP output queuing
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Processor Feature Card Functionality
(The NSP uses the FC-PFQ feature card.)
 12.0(4)DB
on NSP
Strict priority, rate, or weighted round robin scheduling algorithms
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Physical Interfaces
Configuring the Scheduler and Service Class
 12.0(1)DB
on NSP

 

ATM Traffic Classes


Feature Hyperlink & Location Introduced
Available bit rate (ABR) (EFCI + RR) + minimum cell rate (MCR)
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Physical Interfaces
Configuring the Interface Queue Thresholds per Service Category

12.0(4)DB
on NSP
ABR connection support for non-zero MCR
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Physical Interfaces
Configuring the Interface Queue Thresholds per Service Category
(The NSP uses the FC-PFQ feature card.)

12.0(1)DB
on NSP
Constant bit rate (CBR)
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Global Resource Management
 12.0(4)DB
on NSP
Per-VC or per-VP CBR traffic shaping
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Global Resource Management
(The NSP uses the FC-PFQ feature card.)
12.0(4)DB
on NSP
Shaped CBR VP tunnels (up to 128)
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Global Resource Management
(The NSP uses the FC-PFQ feature card.)
12.0(1)DB
on NSP
Substitution of other service categories in shaped VP tunnels
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Physical and Logical Interface Parameters
Configuring Interface Service Category Support
 12.0(1)DB
on NSP
Unspecified bit rate (UBR)
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Global Resource Management
(The NSP uses the FC-PFQ feature card.)
12.0(4)DB
on NSP
UBR + MCR
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Global Resource Management
Configuring the Connection Traffic Table
CTT Supported Features
(The NSP uses the FC-PFQ feature card.)
 12.0(4)DB
on NSP
Variable bit rate-non-real time (VBR-nrt)
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Global Resource Management
(The NSP uses the FC-PFQ feature card.)
12.0(4)DB
on NSP
VBR-real time (VBR-rt)
ATM Switch Router Software Configuration Guide:
Configuring Resource Management
Configuring Global Resource Management
(The NSP uses the FC-PFQ feature card.)
12.0(4)DB
on NSP

 

Configuration and Monitoring


Feature Hyperlink & Location Introduced
ATM access lists on Interim Local Management Interface (ILMI) registration
ATM Switch Router Software Configuration Guide:
Using Access Control
Configuring Per-Interface Address Registration with Optional Access Filters

12.0(1)DB
on NSP
Per-VC or per-VP nondisruptive port snooping
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
Configuring Interface and Connection Snooping
Configuring Per-Connection Snooping
 12.0(1)DB
on NSP

 

Hardware Support


Feature Hyperlink & Location Introduced
1+1 Slot Redundancy (EHSA)
Cisco 6400 Software Setup Guide:
Redundancy and SONET APS Configuration

12.0(1)DB
on NSP
Network Management Ethernet (NME)
Cisco 6400 Software Setup Guide:
Basic NSP Configuration
Network Management Ethernet Interface
 12.0(5)DB
on NSP
NRP-2 support
Cisco 6400 Software Setup Guide:
Basic NSP Configuration
NRP-2 Support
 12.1(4)DB
on NSP
NSP 1+1 Redundancy
Cisco 6400 Software Setup Guide:
Redundancy and SONET APS Configuration
NSP Redundancy
 12.0(1)DB
on NSP
Synchronous Optical Network (SONET) automatic protection switching (APS) support
Cisco 6400 Software Setup Guide:
Redundancy and SONET APS Configuration
SONET APS for NLC Port Redundancy
 12.0(1)DB
on NSP
Stratum 3/BITS
Cisco 6400 Software Setup Guide:
Basic NSP Configuration
Network Clocking
Configuring Building Integrated Timing Supply Network Clocking
 12.0(7)DB
on NSP
Telco alarms
Cisco 6400 Software Setup Guide:
SNMP, RMON, and Alarm Configuration
Alarms
 12.0(1)DB
on NSP

 

IP and Routing


Feature Hyperlink & Location Introduced
Dynamic Host Configuration Protocol (DHCP) client support
Cisco IOS IP and IP Routing Configuration Guide, Release 12.1:
IP Addressing and Services
Configuring DHCP

12.0(1)DB
on NSP
Internet Protocol (IP)
ATM Switch Router Software Configuration Guide:
Configuring IP over ATM
12.0(1)DB
on NSP
Network Time Protocol (NTP)
ATM Switch Router Software Configuration Guide:
Configuring System Management Functions
Configuring the Network Time Protocol
 12.0(1)DB
on NSP
Telnet
Cisco IOS Dial Services Configuration Guide: Terminal Services, Release 12.1:
Terminal Service Configuration
Configuring Dial-In Terminal Services
Configuring Telnet and rlogin
 
Cisco IOS Release 12.0 Dial Solutions Configuration Guide:
Configuring Dial-In Terminal Services
Configure Telnet and UNIX Rlogin
 12.0(1)DB
on NSP

 

Network Management


Feature Hyperlink & Location Introduced
ATM accounting enhancements
ATM Switch Router Software Configuration Guide:
Configuring ATM Accounting and ATM RMON

12.0(1)DB
on NSP
ATM Accounting Management Information Base (MIB)
ATM Switch Router Software Configuration Guide:
Configuring ATM Accounting and ATM RMON
12.0(1)DB
on NSP
ATM remote monitoring (RMON) MIB
ATM Switch Router Software Configuration Guide:
Configuring ATM Accounting and ATM RMON
12.0(1)DB
on NSP
Signaling diagnostics and MIB
ATM Switch Router Software Configuration Guide:
Configuring Signalling Features
Configuring Signalling Diagnostics Tables
 12.0(1)DB
on NSP
Simple Network Management Protocol (SNMP)
Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1:
Cisco IOS System Management
Configuring SNMP Support
Cisco IOS Release 12.0 Configuration Fundamentals Configuration Guide:
 
System Management
Monitoring the Router and Network
Configure SNMP Support
 12.0(1)DB
on NSP
Web Console
Cisco 6400 Software Setup Guide:
Web Console
 12.0(1)DB
on NSP

 

RADIUS/AAA


Feature Hyperlink & Location Introduced
Terminal Access Controller Access Control System Plus (TACACS+) (admin login only)
ATM Switch Router Software Configuration Guide:
Configuring System Management Functions
Configuring TACACS
 
Cisco IOS Security Configuration Guide, Release 12.1:
Security Server Protocols
Configuring TACACS+
Cisco IOS Release 12.0 Security Configuration Guide:
Security Server Protocols
Configuring TACACS+

12.0(1)DB
on NSP

 

Scalability and performance


Feature Hyperlink & Location Introduced
Capability to view used/unused Input Translation Table (ITT) blocks
Cisco 6400 Software Setup Guide:
Optimizing the Number of Virtual Connections on the Cisco 6400
Displaying ITT Allocation
Input Translation Table Management Enhancements, 12.1(4)DB feature module

12.1(4)DB
on NSP
Fragmentation minimization
Cisco 6400 Software Setup Guide:
Optimizing the Number of Virtual Connections on the Cisco 6400
Input Translation Table Management Enhancements, 12.1(4)DB feature module
 12.1(4)DB
on NSP
ITT block shrinking
Cisco 6400 Software Setup Guide:
Optimizing the Number of Virtual Connections on the Cisco 6400
Input Translation Table Management Enhancements, 12.1(4)DB feature module
 12.1(4)DB
on NSP

 

Signaling and Routing


Feature Hyperlink & Location Introduced
ATM Network Service Access Point (NSAP) and left-justified E.164 address support
ATM Switch Router Software Configuration Guide:
Configuring Signalling Features
Configuring E.164 Addresses
ATM Switch Router Command Reference:
A Commands
aesa embedded-number left-justified

12.0(1)DB
on NSP
Closed user groups (CUGs) for ATM VPNs
ATM Switch Router Software Configuration Guide:
Configuring Signalling Features
Configuring Closed User Group Signalling
 12.0(1)DB
on NSP
E.164 address translation and autoconversion
ATM Switch Router Software Configuration Guide:
Configuring Signalling Features
Configuring E.164 Addresses
 12.0(1)DB
on NSP
Hierarchical Private Network Node Interface (PNNI)
ATM Switch Router Software Configuration Guide:
Configuring ATM Routing and PNNI
Basic PNNI Configuration
Guide to ATM Technology:
ATM Routing with IISP and PNNI
PNNI Overview
Hierarchical PNNI
 12.0(1)DB
on NSP
Interim-Interswitch Signaling Protocol (IISP)
Cisco 6400 Software Setup Guide:
Node Line Card Interface Configuration
ATM Interface Types
Interim Interswitch Signaling Protocol Interfaces
Guide to ATM Technology:
ATM Routing with IISP and PNNI
Static Routing with IISP
 12.0(1)DB
on NSP
ILMI 4.0
ATM Switch Router Software Configuration Guide:
Configuring ILMI
Configuring a VPI/VCI Range for SVPs and SVCs
 12.0(1)DB
on NSP
VPI/VCI range support in ILMI 4.0
ATM Switch Router Software Configuration Guide:
Configuring Virtual Connections
 12.0(1)DB
on NSP
UNI 3.0, UNI 3.1, and UNI 4.0
Cisco 6400 Software Setup Guide:
Node Line Card Interface Configuration
ATM Interface Types
User-Network Interfaces
 12.0(4)DB
on NSP


Posted: Fri May 11 16:46:42 PDT 2001
All contents are Copyright © 1992--2001 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.