About this Guide

Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.

This section explains the objectives, intended audience, and organization of this publication and describes the conventions that convey instructions and other information.

This section provides the following information:

• Document Objectives

• Audience

• Document Organization

• Related Documentation

• Document Conventions

• Obtaining Optical Networking Information

• Obtaining Documentation, Obtaining Support, and Security Guidelines

Revision History


Date	Notes
03/27/2007	Revision History Table added for the first time.
09/17/2007	Added a note after steps in the section "DLP-A255 Cross-Connect Card Side Switch Test" in the "DLPs A200 to A299" chapter.

Document Objectives

This guide provides procedures for installation, turn up, provisioning, and acceptance of ONS 15454 nodes and ONS 15454 networks.

Audience

To use this publication, you should be familiar with Cisco or equivalent optical transmission hardware and cabling, telecommunications hardware and cabling, electronic circuitry and wiring practices, and preferably have experience as a telecommunications technician.

Document Organization

The organization of the guide reflects Cisco's recommended work flow for new installations. This organization also provides easy access to procedures and tasks used to modify existing installations. Verification procedures are provided, where necessary, to allow contract vendors to complete the physical installation and then turn over the site to craft personnel for verification, provisioning, turn up, and acceptance.

The front matter of the book appears in the following sequence:

1. Title Page

2. Table of Contents

3. List of Figures

4. List of Tables

5. List of Procedures

6. List of Tasks

The information in the book follows a task-oriented hierarchy using the elements described below.

Chapter (Director Level)

The guide is divided into logical work groups (chapters) that serve as director entry into the procedures. For example, if you are arriving on site after a contractor has installed the shelf hardware, proceed to Chapter 2, "Install Cards and Fiber-Optic Cable" and begin verifying installation and installing cards. You may proceed sequentially (recommended), or locate the work you want to perform from the list of procedures on the first page of every chapter (or turn to the front matter or index). Table 1 describes the guide chapters.

Table 1 Cisco ONS 15454 Procedure Guide Chapters
Title	Summary
Chapter 1, "Install the Shelf and Backplane Cable"	Includes procedures for installing the shelf assembly, electrical interface assemblies (EIAs), power and ground, fan-tray assembly, alarm expansion panel, backplane wires, external wire-wrap panel, electrical card cables, and optional dense wavelength division multiplexing (DWDM) equipment. Also included is the shelf installation acceptance test.
Chapter 2, "Install Cards and Fiber-Optic Cable"	Includes procedures to install common control cards, optical cards, transponder and muxponder cards, electrical cards, Ethernet cards and connectors, FC_MR-4 cards, and DWDM cards. Also included are procedures for removing and replacing a card, preprovisioning a slot, and installing and routing fiber-optic cables.
"Connect the PC and Log into the GUI"	Includes procedures to install the Cisco Transport Controller (CTC), set up a computer for different connection types, and log into the Cisco ONS 15454.
Chapter 4, "Turn Up Node"	Includes procedures to verify the card installation; create users and assign security; set up name, date, time and contact information; set up network access, firewall access, and timing; create protection groups; and provision Simple Network Management Protocol (SNMP).
"Turn Up Network"	Includes procedures to verify the node turn up, and provision and test the following networks: point-to-point, linear ADM, bidirectional line switched ring (BLSR), and path protection. It also includes procedures for subtending rings.
Chapter 6, "Create Circuits and VT Tunnels"	Includes procedures to verify network turn up; create manually or automatically routed circuits or VT tunnels; create unidirectional circuits with multiple drops; create VT aggregation points, half circuits, Ethernet circuits, and overhead circuits; provision a DWDM optical channel network connection; and create virtual concatenated (VCAT) circuits.
Chapter 7, "Manage Alarms"	Includes procedures to document existing node data, view and delete alarms, view alarm-affected circuits and LCD alarm counts, manage alarm profiles, filter alarms, suppress alarms, and provision external alarms.
Chapter 8, "Monitor Performance"	Includes procedures to change the performance monitoring (PM) display, monitor performance, and manage remote monitoring (RMON) thresholds.
"Manage Circuits"	Includes procedures to view circuits and cross-connect resource usage, modify and delete circuits and tunnels, convert and upgrade CTC and TL1 circuits, monitor circuits, and create a J1 path trace.
"Change Card Settings"	Includes procedures to change node management information, CTC network access and view, and DWDM node settings; change or delete card protection settings; delete SONET data communication channel (DCC), line data communication channel (LDCC), generic communication channel (GCC), and DWDM optical service channel (OSC) terminations; and change node timing, security, and Simple Network Management Protocol (SNMP).
"Change Card Settings"	Includes procedures to modify line settings and PM parameter thresholds for cards, modify alarm interface controller settings, and upgrade DS-1 and DS-3 1:1 protection to 1:N protection.
Chapter 12, "Upgrade Cards and Spans"	Includes procedures to prevent an OC-N protection switch during cross-connect upgrades, upgrade or downgrade cards, and upgrade spans automatically or manually.
Chapter 13, "Convert Network Configurations"	Includes procedures to convert network configurations, modify a BLSR, and manage BLSR switches.
Chapter 14, "Add and Remove Nodes"	Includes procedures to add or remove BLSR, path protection, or linear nodes from a network configuration.
Chapter 15, "Maintain the Node"	Includes procedures to inspect and manage the air filter, backup and restore the database, restore the node to factory configuration, off load the security audit trail log, inhibit card protection switching, revert software, clean fiber connectors, reset the TCC2 card using CTC, view Ethernet card maintenance information, change the node timing reference, and view the timing report.
Chapter 16, "Power Down the Node"	Includes the procedure to power down the node.
Chapter 17, "DLPs A1 to A99"	Includes all current tasks (DLPs) from A1 to A99.
"DLPs A100 to A199"	Includes all current tasks from A100 to A199.
Chapter 19, "DLPs A200 to A299"	Includes all current tasks from A200 to A299.
Chapter 20, "DLPs A300 to A399"	Includes all current tasks from A300 to A399.
Chapter 21, "DLPs A400 to A499"	Includes all current tasks from A400 to A499.
"DLPs A500 to A599"	Includes all current tasks from A500 to A599.
"CTC Information and Shortcuts"	Includes a description of the CTC views and window features.

Non-Trouble Procedure (NTP)

Each NTP is a list of steps designed to accomplish a specific procedure. Follow the steps until the procedure is complete. If you need more detailed instructions, refer to the Detailed Level Procedure (DLP) specified in the procedure steps.

Note Throughout this guide, NTPs are referred to as "procedures" and DLPs are termed "tasks." Every reference to a procedure includes its NTP number, and every reference to a task includes its DLP number.

Detailed Level Procedure (DLP)

The DLP (task) supplies additional task details to support the NTP. The DLP lists numbered steps that lead you through completion of a task. Some steps require that equipment indications be checked for verification. When the proper response is not obtained, the DLP provides a trouble clearing reference.

Document Conventions

This publication uses the following conventions:


Convention	Application
boldface	Commands and keywords in body text.
italic	Command input that is supplied by the user.
[ ]	Keywords or arguments that appear within square brackets are optional.
{ x \| x \| x }	A choice of keywords (represented by x) appears in braces separated by vertical bars. The user must select one.
Ctrl	The control key. For example, where Ctrl + D is written, hold down the Control key while pressing the D key.
`screen font`	Examples of information displayed on the screen.
boldface screen font	Examples of information that the user must enter.
< >	Command parameters that must be replaced by module-specific codes.

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.

Caution

Means reader be careful. In this situation, the user might do something that could result in equipment damage or loss of data.


Warning	IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS
Waarschuwing	BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES
Varoitus	T�RKEIT� TURVALLISUUSOHJEITA T�m� varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin k�sittelet laitteistoa, huomioi s�hk�piirien k�sittelemiseen liittyv�t riskit ja tutustu onnettomuuksien yleisiin ehk�isytapoihin. Turvallisuusvaroitusten k��nn�kset l�ytyv�t laitteen mukana toimitettujen k��nnettyjen turvallisuusvaroitusten joukosta varoitusten lopussa n�kyvien lausuntonumeroiden avulla. S�ILYT� N�M� OHJEET
Attention	IMPORTANTES INFORMATIONS DE S�CURIT� Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entra�ner des blessures ou des dommages corporels. Avant de travailler sur un �quipement, soyez conscient des dangers li�s aux circuits �lectriques et familiarisez-vous avec les proc�dures couramment utilis�es pour �viter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de s�curit� traduites qui accompagnent cet appareil, r�f�rez-vous au num�ro de l'instruction situ� � la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS
Warnung	WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen f�hren kann. Machen Sie sich vor der Arbeit mit Ger�ten mit den Gefahren elektrischer Schaltungen und den �blichen Verfahren zur Vorbeugung vor Unf�llen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen �bersetzung in den �bersetzten Sicherheitshinweisen, die zusammen mit diesem Ger�t ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza	IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI
Advarsel	VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan f�re til skade p� person. F�r du begynner � arbeide med noe av utstyret, m� du v�re oppmerksom p� farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for � forhindre ulykker. Bruk nummeret i slutten av hver advarsel for � finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE P� DISSE INSTRUKSJONENE
Aviso	INSTRU��ES IMPORTANTES DE SEGURAN�A Este s�mbolo de aviso significa perigo. Voc� est� em uma situa��o que poder� ser causadora de les�es corporais. Antes de iniciar a utiliza��o de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos el�tricos e familiarize-se com as pr�ticas habituais de preven��o de acidentes. Utilize o n�mero da instru��o fornecido ao final de cada aviso para localizar sua tradu��o nos avisos de seguran�a traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRU��ES
�Advertencia!	INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este s�mbolo de aviso indica peligro. Existe riesgo para su integridad f�sica. Antes de manipular cualquier equipo, considere los riesgos de la corriente el�ctrica y familiar�cese con los procedimientos est�ndar de prevenci�n de accidentes. Al final de cada advertencia encontrar� el n�mero que le ayudar� a encontrar el texto traducido en el apartado de traducciones que acompa�a a este dispositivo. GUARDE ESTAS INSTRUCCIONES
Varning!	VIKTIGA S�KERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utf�r arbete p� n�gon utrustning m�ste du vara medveten om farorna med elkretsar och k�nna till vanliga f�rfaranden f�r att f�rebygga olyckor. Anv�nd det nummer som finns i slutet av varje varning f�r att hitta dess �vers�ttning i de �versatta s�kerhetsvarningar som medf�ljer denna anordning. SPARA DESSA ANVISNINGAR





Aviso	INSTRU��ES IMPORTANTES DE SEGURAN�A Este s�mbolo de aviso significa perigo. Voc� se encontra em uma situa��o em que h� risco de les�es corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos el�tricos e familiarize-se com as pr�ticas padr�o de preven��o de acidentes. Use o n�mero da declara��o fornecido ao final de cada aviso para localizar sua tradu��o nos avisos de seguran�a traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRU��ES
Advarsel	VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. F�r du begynder arbejde p� udstyr, skal du v�re opm�rksom p� de involverede risici, der er ved elektriske kredsl�b, og du skal s�tte dig ind i standardprocedurer til undg�else af ulykker. Brug erkl�ringsnummeret efter hver advarsel for at finde overs�ttelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER

Obtaining Optical Networking Information

This section contains information that is specific to optical networking products. For information that pertains to all of Cisco, refer to the Obtaining Documentation, Obtaining Support, and Security Guidelines section.

Where to Find Safety and Warning Information

For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15454 system. It also includes translations of the safety warnings that appear in the ONS 15454 system documentation.

Cisco Optical Networking Product Documentation CD-ROM

Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.

Obtaining Documentation, Obtaining Support, and Security Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Table Of Contents