Specifications

Introduction

This appendix provides information concerning the point-to-point broadband fixed wireless system and its Cisco-supported components.

System Specifications

Table B-1 lists specifications for the broadband fixed wireless system.

Table B-1: System Specifications

Description	Specification
Operating environment	Line-of-sight or near line-of-sight
Data rate (full duplex)	Up to 44.4 Mbps on 12-MHz channels
Power supply requirements	-48 VDC @ 3A
Transmit power level	+5 to +25 dBm
Channel bandwidth	6 or 12 MHz (selectable)
Frequency band	5.725 to 5.825 GHz
Transmit distance: Line of sight Near line-of-sight	Up to 15 miles 3 to 5 miles (depending on conditions)
Modulation type	64 QAM on VOFDM
Antenna diversity	Available as an option
Line card to transverter connection: Frequency reference: Frequency Power Cabling: Cable loss DC resistance	24 MHz -12 dBm minimum, -5 dBm maximum 17 dB maximum at 420 MHz 15 dB maximum at 324 MHz 1.6 ohms maximum
Temperature, inside equipment (operating)	-32 to 104ºF (0 to 40ºC)
Temperature, inside equipment (storage)	-4 to 149ºF (20 to 65ºC)
Temperature, outside equipment (operating)	-40 to 122ºF (-40 to 55ºC)
Temperature, outside equipment (storage))	-40 to 185ºF (-40 to 85ºC)
Humidity, inside equipment	5 to 95% noncondensing
Humidity, outside equipment	Up to 100%
Altitude (maximum)	13,000 ft. (4500 m)

Receiver Sensitivity

Table B-2 lists specifications for minimum receiver sensitivity.

Table B-2: Minimum Receiver Sensitivity (AWGN (flat) RF Channel)

Number of Antennas	Throughput Setting	Bandwidth (MHz)	Network Throughput (Mbps)	Delay Spread Tolerance (µs)	Minimum Sensitivity (dBm)
1	High	6	22.1	1.5	-79
2	High	6	22.1	1.5	-82
1	Medium	6	19.1	6.8	-79
2	Medium	6	19.1	6.8	-82
1	Low	6	10.9	6.8	-84
2	Low	6	10.9	6.8	-87

1	High	12	44.4	2.4	-76
2	High	12	44.4	2.4	-79
1	Medium	12	38.7	7.8	-76
2	Medium	12	38.7	7.8	-79
1	Low	12	22.1	7.8	-81
2	Low	12	22.1	7.8	-84

Signal-to-Noise Ratio

Table B-3 lists the required signal-to-noise ratio (SNR) at a bit error rate (BER) of 10^-10 for the wireless modem card.

Table B-3: Required Signal-to-Noise Ratio @ BER 10^-10

Number of Antennas	Throughput Setting	Bandwidth (MHz)	Network Throughput (Mbps)	AWGN (dB)	Rayleigh (dB)
1	High	6	22.1	22	34
2	High	6	22.1	19	24
1	Medium	6	19.1	22	34
2	Medium	6	19.1	19	24
1	Low	6	10.9	17	21
2	Low	6	10.9	14	16

1	High	12	44.4	22	34
2	High	12	44.4	19	24
1	Medium	12	38.7	22	34
2	Medium	12	38.7	19	24
1	Low	12	22.1	17	21
2	Low	12	22.1	14	16

Table B-4 lists physical specifications and power requirements for the Cisco uBR7223, Cisco uBR7246, and Cisco uBR7246 VXR universal broadband routers. For additional information, refer to the Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide.

Table B-4: Router Specifications

Description	Specification
Midplane	Two primary PCI buses and one secondary PCI bus with an aggregate bandwidth of 600 Mbps
Dimensions (H x W x D): uBR7223 uBR7246, uBR7246 VXR	6.70 x 17.38 x 21.25 in. (17.02 x 44.15 x 53.98 cm) 10.5 x 17.00 x 21.25 in. (26.67 x 43.18 x 53.98 cm)
Weight: uBR7223 uBR7246, uBR7246 VXR	Chassis fully configured with a network processing engine, I/O controller, one port adapter, two wireless modem cards, one power supply, and a fan tray: ~ 75 lb (34.0 kg) Chassis fully configured with a network processing engine, I/O controller, two port adapters, four wireless modem cards, two power supplies, and a fan tray: ~ 100 lb (45.4 kg)
Heat dissipation: uBR7223 uBR7246, uBR7246 VXR	700W (2388 Btu), 300W typical 800W (2730 Btu)
AC-input power: uBR7223 uBR7246, uBR7246 VXR	700W maximum, 300W typical 800W maximum (with either a single or dual power supply configuration)
AC-input voltage	100 to 240 VAC wide input with power factor correction
AC-input current rating: uBR7223 uBR7246, uBR7246 VXR	7A with the chassis fully configured 7A maximum at 110 VAC and 3.5A maximum at 240 VAC with the chassis fully configured.
AC-input cable	18 AWG (0.82 mm²) three-wire cable, with a three-lead IEC-320 receptacle on the power supply end and a country-dependent plug on the power source end
DC-input voltage rating	-48 VDC nominal in North America -60 VDC nominal in the European Community
DC-input current rating: uBR7223 uBR7246, uBR7246 VXR	14A maximum (7.7A typical draw at -48 VDC, 6.2A typical draw at -60 VDC) Not to exceed 13A maximum at -48 VDC (370W/-48 VDC = 7.7A typical draw) Not to exceed 8A maximum at -60 VDC (370W/-60 VDC = 6.2A typical draw)
DC-input cable	12 AWG (3.91 mm²) recommended minimum, with at least three conductors rated for at least 140ºF (60ºC)
DC-output power: uBR7223 uBR7246, uBR7246 VXR	550W maximum (with a single power supply configuration; dual power not supported) 550W maximum (with either a single or dual power supply configuration)
DC voltages supplied	+3.5V, +5.2V, +12.2V, -12.2V, +16V, -16V
Frequency	50/60 Hz
Airflow: uBR7223 uBR7246, uBR7246 VXR	~80 cfm ~120 cfm
Temperature	32º to 104ºF (0º to 40ºC) operating; -4º to 149ºF (-20º to 65ºC) storage
Humidity	10 to 90% noncondensing

Wireless Modem Card Specifications

Table B-5 lists specifications for the wireless modem card. For additional information regarding the wireless modem card, refer to the Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration document.

Table B-5: Wireless Modem Card Specifications

Description	Specifications
Dimensions (H x W x D)	1.35 x 13.5 x 10.56 in. (3.43 x 34.29 x 26.82 cm)
Power dissipation Voltage	45W Supplied through uBR router chassis
Transmitter Output frequency Output bandwidth Output power	324 MHz 6 or 12 MHz (selectable) -3 dBm maximum
Receiver Input frequency Input bandwidth Operating input power Modem noise figure IF frequency reference	420 MHz 6 or 12 MHz (selectable) -20 dBm maximum 12.5 dB typical @minimum AGC setting 24 MHz ±5.5 ppm
Data control link: Transceiver data Data rate Signaling	RS-485 (differential: full duplex) 1.5 Mbps Manchester, UART protocol
Connectors: IF to main transverter IF to diversity transverter Control cable to main transverter Control cable to diversity transverter 10-MHz external reference clock	SMA (female) SMA (female) RJ-45 RJ-45 SMA (female)
Router mainframe	uBR7223, uBR7246, or uBR7246 VXR
Modulation	64 QAM on VOFDM
Data rate (full duplex)	Up to 44.4 Mbps in a 12-MHz channel Up to 22.1 Mbps in a 6-MHz channel
Temperature	32 to 104ºF (0 to 40ºC) operating -40 to 185ºF (-40 to 85ºC) storage
Humidity	10 to 90% noncondensing
Altitude (maximum)	15000 ft. (4572 m)
Impedance	50 ohms (nominal)

Power Feed Panel Specifications

Table B-6 lists specifications for the power feed panel. For additional information regarding the power feed panel, refer to the Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration document.

Table B-6: Power Feed Panel Specifications

Description	Specification
Dimensions (H x W x D)	1.8 x 17.5 x 11.3 in. (4.4 x 44.5 x 28.6 cm)
Weight	7.5 lb (3.4 kg)
DC-input voltage rating	-48V nominal, 15A, 720 VA (-40.5 to -57.0 VDC)
RF loss	0.75 dB @ 400 MHz
DC Resistance	0.25 ohms typical
Power dissipation	6W
Temperature	32 to 122ºF (0 to 50ºC) operating -4 to 149ºF (-20 to 65ºC) storage
Humidity	10 to 85% noncondensing
Connectors: IF/RF: Diversity antenna port to transverter Diversity antenna port to modem card Main antenna port to modem card Main antenna port to transverter Control: Main antenna port to transverter Main antenna port to modem card Diversity antenna port to modem card Diversity antenna port to transverter	N-type (female) SMA (female) SMA (female) N-type (female) DB-9 (female) RJ-45 (female)) RJ-45 (female) DB-9 (female)

Table of Contents

Specifications