Fujitsu F9600ES V11 PBX with CallManager using 2621-T1 PRI DMS-100 Gateway

Table Of Contents

Application Note

Integration Description

System Components

Feature

Network Diagram

Configuring the Fujitsu F9600ES PBX

Configure ISDN Trunk

Class of Service

Trunk Group

Numbering Plan

Change Service Parameters

ARS Code, ARS Routes, ARS Dial Plan

ARS Digit Manipulation

Cisco CallManager Configuration

Considerations

User/Network Settings

Calling Name and Number feature

Appendix A

Cisco CallManager Software Release

Fujitsu F9600ES Software release

Cisco 2621 Router Configuration

Test Configuration

Appendix B

Test Results

Application Note

Fujitsu F9600ES V11 PBX with CallManager using 2621-T1 PRI DMS-100 Gateway

This application note illustrates connectivity for Fujitsu F9600ES V11 PBX with CallManager using 2621-T1 PRI DMS-100 Gateway.

Integration Description

Connectivity is achieved by using the Fujitsu DMS-100 PRI protocol. The Fujitsu F9600ES can be configured as either NETWORK or USER side.

The network topology diagram presented in Figure 1 illustrates the test set-up.

System Components

Cisco Systems equipment:

•Hardware (Cisco 2621 Gateway): 2MFT T1 Port

•Software: CallManager Release 3.1

PBX hardware and software requirements:

•Hardware:

–BDTKAA (T-1 Carrier Interface Trunk card A)

–B2DK2C (T-1 Line Trunk Adapter Card)

•Software: Version E12V11L22

Feature

Key features supported:

•Calling/Called Number

Key features not supported:

•Calling Name

•Connected Name

•Connected Number

Network Diagram

Figure 1

Network Test Topology

Configuring the Fujitsu F9600ES PBX

Configure in the following sequence:

1. "Configure ISDN Trunk" on page 3

2. "Class of Service" on page 5

3. "Trunk Group" on page 5

4. "Numbering Plan" on page 6

5. "Change Service Parameters" on page 8

6. "ARS Code, ARS Routes, ARS Dial Plan" on page 9

7. "ARS Digit Manipulation" on page 10

Configure ISDN Trunk

# ISDN TRUNK ASSIGNMENT LIST # 01-12-18 TUE 11:31 PAGE-001

TNN TGN EN MS PRTCL QDID FNA SUBDID DID UNA RSS RSASG
USPID TID

0 170 00002000 1 6

0 171 00002002 - - ALL ALL - - -

0 171 00002003 - - ALL ALL - - -

0 171 00002004 - - ALL ALL - - -

0 171 00002005 - - ALL ALL - - -

0 171 00002006 - - ALL ALL - - -

0 171 00002007 - - ALL ALL - - -

0 171 00002008 - - ALL ALL - - -

0 171 00002009 - - ALL ALL - - -

0 171 00002010 - - ALL ALL - - -

0 171 00002011 - - ALL ALL - - -

0 171 00002012 - - ALL ALL - - -

0 171 00002013 - - ALL ALL - - -

0 171 00002014 - - ALL ALL - - -

0 171 00002015 - - ALL ALL - - -

0 171 00002016 - - ALL ALL - - -

0 171 00002017 - - ALL ALL - - -

0 171 00002018 - - ALL ALL - - -

0 171 00002019 - - ALL ALL - - -

0 171 00002020 - - ALL ALL - - -

0 171 00002021 - - ALL ALL - - -

0 171 00002022 - - ALL ALL - - -

0 171 00002023 - - ALL ALL - - -

0 171 00002024 - - ALL ALL - - -

END 01-12-18 TUE 11:32 (CISCO LAB ES R13)

DIS ISINF,170,171 (To Display Trunk Group Information)

# ISDN TRUNK INFORMATION LIST # 01-12-18 TUE 11:32 PAGE-001

# ONE-INTERFACE #

< D-CHANNEL >

TNN TGN EN MS PRTCL

0 170 00002000 1 DMS100

< B-CHANNEL >

TNN TGN EN QDID FNA SUBDID DID UNA RSS RSASG TYP NSF

0 171 00002002 - - ALL ALL - - - MUL 0
0 171 00002003 - - ALL ALL - - - MUL 0
0 171 00002004 - - ALL ALL - - - MUL 0
0 171 00002005 - - ALL ALL - - - MUL 0
0 171 00002006 - - ALL ALL - - - MUL 0
0 171 00002007 - - ALL ALL - - - MUL 0
0 171 00002008 - - ALL ALL - - - MUL 0
0 171 00002009 - - ALL ALL - - - MUL 0
0 171 00002010 - - ALL ALL - - - MUL 0
0 171 00002011 - - ALL ALL - - - MUL 0
0 171 00002012 - - ALL ALL - - - MUL 0
0 171 00002013 - - ALL ALL - - - MUL 0
0 171 00002014 - - ALL ALL - - - MUL 0
0 171 00002015 - - ALL ALL - - - MUL 0
0 171 00002016 - - ALL ALL - - - MUL 0
0 171 00002017 - - ALL ALL - - - MUL 0
0 171 00002018 - - ALL ALL - - - MUL 0
0 171 00002019 - - ALL ALL - - - MUL 0
0 171 00002020 - - ALL ALL - - - MUL 0
0 171 00002021 - - ALL ALL - - - MUL 0
0 171 00002022 - - ALL ALL - - - MUL 0
0 171 00002023 - - ALL ALL - - - MUL 0
0 171 00002024 - - ALL ALL - - - MUL 0

< CBC GROUP TGN >

PILOT MTGN - NSF MTGN - NSF MTGN - NSF MTGN - NSF

NONE

END 01-12-18 TUE 11:32 (CISCO LAB ES R13)
Class of Service

DIS COSF,,1,1 (To Display Class of Service Features)

# COS CHECK TABLE LIST # 01-12-18 TUE 11:33 PAGE-001

TNN COS --------------AVAILABLE FEATURE NUMBER (FNO)---------------

0 1 70 71 72 75 76 130 135 138 302 304 318 335 339 348 354
355 363 365 398 401 404 415 417 422 440 445 458 459 496 498
540 581 591

END 01-12-18 TUE 11:33 (CISCO LAB ES R13)

Trunk Group

DIS TG,170,171,1 (To Display Trunk Group Information)

# TRUNK GROUP DATA LIST # 01-12-18 TUE 11:33 PAGE-001

TGN TYP TID TNN SPC AKI COF TLT DGN RGN COS RSM FRL TRS HNT NAME
AKW AKR AKB RGT AOT GRD REL HKS AFT SHK RHK OPR DMF
MIN PRE MAK BRK DGT PST PBO PBF COP PGT MID
PAC MBC STG DT IAS DTS ABS DTK OOC NOC PTF TCS TCR TDT VCM OGF
CRC
NSF NSFFG PRMFF PRMFV CDNFG TON NPI

170 5 37 0 4 0 0 0 1 1 1 1 1 0 0
0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0
28 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0

171 5 38 0 5 0 0 0 0 0 1 1 1 0 1
0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0
28 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0

END 01-12-18 TUE 11:33 (CISCO LAB ES R13)

Numbering Plan

DIS NP,,1 (To Display Numbering Plan)

# NUMBERING PLAN LIST # 01-12-18 TUE 11:33 PAGE-001

TTID= 1

DIGIT EDL FNO TGN TGX AJC RDD DOC TTN DN SVN

0 1 40 0
3 4 591 191 1 1
40 4 25 0 2 0
41 4 25 0 2 0
70 30 540 171 2 4 0
71 30 581 181 2 0
72 6 591 150 2 1
73 30 581 128 2 0
74 30 581 129 2 0
75 30 517 140 2 2
9 30 301 0 1 0
*11 3 72 0 0
*20 7 138 0 3 0
*21 3 415 0 0
*51 3 72 0 0
*70 5 398 0 1 0
*71 5 398 0 1 0
*72 5 398 0 1 0
*73 5 398 0 1 0
*74 5 398 0 1 0
#67 4 401 0 0
D3D 7 138 0 3 0
D88 30 304 0 3 0

END 01-12-18 TUE 11:33 (CISCO LAB ES R13)

DIS MLDT,,4101,4102 (To Display Multi-line Digital Stations)

# MLDT ASSIGNMENT LIST # 01-12-18 TUE 11:34 PAGE-001

DN( EN ) TYPE RSM FRL COS OT USG SPDL PD HSC KA
BM LA PP RP IP HF TT RB AH PS LT PDN
NAME AMPT

4101(00080802) 3 1 1 1 0 0 2 3 1
0 1 1 1 1 1 1 1 1 0 0
'MADRAS' 0

4102(00080804) 3 1 1 1 0 0 0 3 1
0 1 1 1 1 1 1 1 1 0 0
'TIKA MASALA' 0

END 01-12-18 TUE 11:34 (CISCO LAB ES R13)

DIS MLDT,,4101,4102 (To Display Multi-line Digital Stations)

# MLDT ASSIGNMENT LIST # 01-12-18 TUE 11:34 PAGE-001

DN( EN ) TYPE RSM FRL COS OT USG SPDL PD HSC KA
BM LA PP RP IP HF TT RB AH PS LT PDN
NAME AMPT

4101(00080802) 3 1 1 1 0 0 2 3 1
0 1 1 1 1 1 1 1 1 0 0
'MADRAS' 0

4102(00080804) 3 1 1 1 0 0 0 3 1
0 1 1 1 1 1 1 1 1 0 0
'TIKA MASALA' 0

END 01-12-18 TUE 11:34 (CISCO LAB ES R13)

Change Service Parameters

DIS SVP,2,116,116 (To enable Calling Line Identification sending to Public ISDN)

# SERVICE LIST # 01-12-18 TUE 11:34 PAGE-001

TYPE = 2 ( SVSDT )

ID-----DATA ID-----DATA ID-----DATA ID-----DATA ID-----DATA

116 1

END 01-12-18 TUE 11:34 (CISCO LAB ES R13)

DIS SVP,2,218,218 (To provide Calling Party Number to Public ISDN)

# SERVICE LIST # 01-12-18 TUE 11:34 PAGE-001

TYPE = 2 ( SVSDT )

ID-----DATA ID-----DATA ID-----DATA ID-----DATA ID-----DATA

218 1

END 01-12-18 TUE 11:34 (CISCO LAB ES R13)

DIS SVP,2,242,242 (To provide ISDN Name Display over Public Network)

# SERVICE LIST # 01-12-18 TUE 11:34 PAGE-001

TYPE = 2 ( SVSDT )

ID-----DATA ID-----DATA ID-----DATA ID-----DATA ID-----DATA

242 1

END 01-12-18 TUE 11:34 (CISCO LAB ES R13)

DIS SVP,2,180,180 (To provide DMS100 Network Name Display)

# SERVICE LIST # 01-12-18 TUE 11:34 PAGE-001

TYPE = 2 ( SVSDT )

ID-----DATA ID-----DATA ID-----DATA ID-----DATA ID-----DATA

180 1

END 01-12-18 TUE 11:34 (CISCO LAB ES R13)

ARS Code, ARS Routes, ARS Dial Plan

DIS ARSC (To Display ARS Code)

# ARS CODE NUMBER LIST # 01-12-18 TUE 11:35 PAGE-001

CDNID DS---ARSTB DS---ARSTB DS---ARSTB

ACDN(1) 2 1 3 1 4 1
5 1 6 1 7 1
8 1 9 1

OCDN(2) 2 2 3 2 4 2
5 2 6 2 7 2
8 2 9 2

END 01-12-18 TUE 11:35 (CISCO LAB ES R13)

DIS ARSR (To Display ARS Routes)

# ARS ROUTE TABLE LIST # 01-12-18 TUE 11:35 PAGE-001

ARSTB TNN POS TGN FRL PTNNO T0 T1 T2 T3 T4 T5 T6 T7 LARF CMPF
(NARSTB) CDNFG TON NPI NAMF

2 0 1 171 0 2 * * * * * * * *
0 0 0 1

10 0 1 0 0 0 * * * * * * * *

END 01-12-18 TUE 11:35 (CISCO LAB ES R13)

DIS ARSDP (To Display ARS Dial Plan)

# ARS RDG QADP LIST # 01-12-18 TUE 11:35 PAGE-001

ARSDG ARSRG QADP

1 0 0

CICF OTPF TOTPF IOTPF DFDSLO

1 1 1 1 3

END 01-12-18 TUE 11:35 (CISCO LAB ES R13)

ARS Digit Manipulation

DIS ARSDM (To Display ARS Digit Manipulation)

# ARS DIGIT MANIPULATION PATTERN LIST # 01-12-18 TUE 11:35 PAGE-001

PTNNO PRDEL --------PRADG------- PSDEL --------PSADG------- ACPOS ADPN SP

0 0 0 0 0
1 0 1 0 0 0
2 3 0 0 0
7 0 7 0 0 0
11 3 0 0 0

END 01-12-18 TUE 11:35 (CISCO LAB ES R13)

DIS MCLKS (To Display Main Clock Source/Status)

# MAIN CLOCK STATUS DISPLAY # 01-12-18 TUE 11:34

< OPERATION STATUS >

MCLK #0 *

IN 0

< ALARM STATUS >

MCLK #0 NORMAL

IN 0 TROUBLE

END 01-12-18 TUE 11:34 (CISCO LAB ES R13)

Cisco CallManager Configuration

H.323 (Cisco 2621) Gateway Configuration

Route Pattern Configuration

Considerations

User/Network Settings

The Cisco 2621 router with ISDN switch type setting of primary-DMS-100 supports "User" protocol side only by using the isdn protocol-emulate user command. Therefore the Fujitsu PBX must be set to emulate Network side.

Calling Name and Number feature

When calling from Cisco 7960 IP phone to Fujitsu digital phone, Calling Number is displayed on both phones after the call is answered. "Calling Name" however is not displayed on either phone even though the Cisco Gateway was sending both Calling Name and Number in the SETUP message.

When calling from Fujitsu digital phone to Cisco 7960 IP phone, IP phone displays Connected Name and Number after the call is answered. Fujitsu phone however did not get updated when the call is answered. It displays the numbers being dialed instead (i.e. Access code + 7 digit number). It was verified using ISDN protocol analyzer that the Cisco Gateway was not sending "Connected Number" or "Connected Name" information in the connect message back to PBX.

Appendix A

Cisco CallManager Software Release

Fujitsu F9600ES Software release

DIS SOFT (To Display PBX Software Version)

01-12-18 TUE 11:31

*** SERVICE SOFTWARE LIST ***

ALL RIGHTS RESERVED,COPYRIGHT(C)1986 FUJITSU LIMITED
LICENSED MATERIAL PROGRAM PROPERTY OF FUJITSU

LPE23924 E12V11L22 C00 000314 INSTALLED

NAME TYPE E/V

BASCP/D120 360507-D E12V11
ATTBS BASIC--D V08
IPRCBS 360561-D V06
IBRSBS 360562-D V01
IPCH0S 360599-D V01
IPREBS 360600-D V01
IPEH0S 360601-D V01
QSIGBS 360974-D V02

END 01-12-18 TUE 11:31 (CISCO LAB ES R13)

Cisco 2621 Router Configuration

2621_B#sh version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(3.5)T, MAINTENANCE INTERIM S
OFTWARE
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 03-Aug-01 22:45 by ccai
Image text-base: 0x80008088, data-base: 0x81631DD8

ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)

2621_B uptime is 1 hour, 1 minute
System returned to ROM by power-on
System image file is "flash:c2600-js-mz.122-3.5.T"

cisco 2621 (MPC860) processor (revision 0x200) with 56320K/9216K bytes of memory
.
Processor board ID JAD051516TX (503811939)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
24 Serial network interface(s)
2 Channelized T1/PRI port(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
2621_B#
_______________________________________________________________________________________ __

2621_B#sh diag
Slot 0:
C2621 2FE Mainboard Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 2.0
PCB Serial Number : JAD051516TX (503811939)
Part Number : 73-3200-08
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : A0
Deviation Number : 0-21249
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 A2 41 02 00 C1 17 4A 41 44 30 35 31
0x10: 35 31 36 54 58 20 28 35 30 33 38 31 31 39 33 39
0x20: 29 82 49 0C 80 08 04 00 81 00 00 00 00 42 41 30
0x30: 80 00 00 53 01 FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Slot 1:
High Density Voice Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.1
Top Assy. Part Number : 800-03567-01
Board Revision : F1
Deviation Number : 0-0
Fab Version : 02
PCB Serial Number : JAB05080LU9
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 CC 41 01 01 C0 46 03 20 00 0D EF 01
0x10: 42 46 31 80 00 00 00 00 02 02 C1 8B 4A 41 42 30
0x20: 35 30 38 30 4C 55 39 03 00 81 00 00 00 00 04 00
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

VIC Slot 0:
T1 (2 Port) Multi-Flex Trunk WAN Daughter Card
Hardware revision 1.0 Board revision B0
Serial number 21936864 Part number 800-04477-02
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 22 01 00 01 4E BA E0 50 11 7D 02 00 00 00 00
0x30: 58 00 00 00 00 10 12 00 FF FF FF FF FF FF FF FF

HDV firmware: Compiled Fri 23-Mar-01 00:20 by miriyala
HDV memory size 524280 heap free 175065

2621_B#
_______________________________________________________________________________________ __

2621_B#sh controllers t1 1/0
T1 1/0 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20010710, FPGA: 15
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
Data in current interval (158 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
2621_B#
_______________________________________________________________________________________ __

2621_B#sh configuration
Using 1861 out of 29688 bytes
!
version 12.2
no parser cache
service timestamps debug datetime msec localtime show-timezone
service timestamps log uptime
no service password-encryption
!
hostname 2621_B
!
no logging buffered
enable password cisco
!
!
!
memory-size iomem 15
voice-card 1
dspfarm
!
ip subnet-zero
!
!
no ip domain-lookup
!
isdn switch-type primary-ni
!
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g711ulaw
codec preference 3 g711alaw
!
!
!
!
!
!
!
controller T1 1/0
framing esf
linecode b8zs
pri-group timeslots 1-24
!
controller T1 1/1
shutdown
framing sf
linecode ami
!
!
!
!
interface FastEthernet0/0
ip address 192.168.100.2 255.255.255.0
no ip mroute-cache
load-interval 30
no keepalive
speed auto
half-duplex
!
interface FastEthernet0/1
ip address 10.1.1.129 255.255.255.0
no ip mroute-cache
duplex auto
speed auto
!
interface Serial1/0:23
no ip address
no logging event link-status
isdn switch-type primary-dms100
isdn incoming-voice voice
isdn T321 30000
isdn T310 40000
no cdp enable
!
router rip
network 1.0.0.0
network 192.168.100.0
!
ip classless
no ip http server
ip pim bidir-enable
!
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
!
snmp-server packetsize 4096
snmp-server manager
tftp-server nvram
call rsvp-sync
!
voice-port 1/0:23
!
!
mgcp profile default
!
dial-peer cor custom
!
!
!
dial-peer voice 1 pots
destination-pattern 41..
progress_ind alert enable 8 [hiden command to get ring-back tone]
direct-inward-dial
port 1/0:23
prefix 41
!
dial-peer voice 3 voip
destination-pattern 40..
progress_ind setup enable 3 [required command to get ring-back tone]
voice-class codec 1
session target ipv4:10.1.1.2
dtmf-relay h245-alphanumeric
ip qos dscp cs5 media
!
!
line con 0
exec-timeout 0 0
line aux 0
exec-timeout 0 0
line vty 0 4
exec-timeout 0 0
password cisco
login
line vty 5 15
exec-timeout 0 0
login
!
scheduler allocate 3996 1000
!
end

2621_B#

Test Configuration

Figure 2

Test Topology

As shown in the diagram above, a Fujitsu F9600ES PBX was connected via an ISDN T1 PRI link to a Cisco 2621 Gateway, which in turn, was connected to an Ethernet switch. The interoperability testing involved Layers 1, 2 and 3 on the ISDN PRI link between a Cisco 2621 and the PBX.

Layer 1 (Physical Layer)

The Fujitsu F9600ES PBX was set for Extended Superframe (ESF) and B8ZS linecoding method. Issue DIS TGDC to display Trunk Group Data Control.

Layers 2 & 3 (Q.921 and Q.931)

Layer 2 and 3 packet exchanges were monitored using an Acacia Clarinet protocol analyzer, bridged across the PRI link in high impedance mode.

Layer 2 Q.921 packets were monitored to ensure that each PBX/2621 software configuration properly exchanged SABME/UA packets to initialize the ISDN link, and then RR packets were exchanged every 30 seconds.

Layer 3 Q.931 packets were monitored to ensure that the appropriate call setup/teardown packets were exchanged for each configuration, and that the SETUP packets contained the mandatory Information Elements with the necessary details, as well as optional IEs such as Calling Name and Number.

Telephone calls were made end-to-end in both directions through the Cisco 2621 Gateway, and a check was made to ensure that there was an audio path in both directions for each call.

User/Network Settings

The Cisco 2621 Gateway with ISDN protocol type setting of primary-DMS-100 supports "User" protocol side only by using the isdn protocol-emulate user command. Therefore the Fujitsu PBX must be set to emulate "Network" side.

The protocol type and protocol side cannot be changed in the "Change" or "Modify" ISDN trunk screens on the Fujitsu PBX EMML Console. The protocol type and the Master/Slave (or Network/User) settings had to be changed for every test case by deleting and building a new trunk group on the Fujitsu. The Fujitsu "Master" matches up with the Cisco Gateway "User", and Fujitsu "Slave" matches up with Cisco Gateway "Network". These settings are specified in the fields [MS] (where 0 = slave and 1 = master); and the [PRTCL] field.

Appendix B

Test Results

Testing was performed by Test Engineer(s): Samir Batio, December 20, 2001

Test Setup

Test configuration:

•PBX1 configured as PRI DMS-100, emulates Network

•Cisco 2621 Gateway configured as PRI DMS-100, emulates User

Table 1  Test Setup Switch and Gateway Settings

Fujitsu F9600ES Switch-type / Protocol-side Setting

Cisco 6608-T1 ISDN Protocol-type/Protocol-side Setting

DMS100 / Master

PRI DMS-100/User

Table 2  Basic Calls: (Enbloc Sending)

Calls Made

Call Comp?

"Calling Number" Passed to Final Destination?

"Calling Name" Passed to Final Destination?

"Called Number" Passed to Orig. Side?

"Called Name" Passed to Orig. Side?

Notes

Phone A to Phone C

Yes

Yes

Yes

No

No

¹

Phone C to Phone A

Yes

Yes

No

Yes

No

¹ CallManager is not sending "Connected Name" or "Connected Number" information in the connect message back to PBX.

Table 3  Call Transfers: (Supervised Local Transfers)

Calls Made

Call Comp?

Orig. "Calling Number" displayed on Final Dest. phone?

Orig. "Calling Name" displayed on Final Dest. phone?

"Called Number" display on Orig. phone updated after transfer?

"Called Name" display on Orig. phone updated after transfer?

Notes

Phone C to Phone A Xfr to Phone B

Yes

Yes

No

No

No

Phone A to Phone C Xfr to Phone D

Yes

Yes

Yes

No

No

Table 4  Call Conferencing (Local)

Calls Made

Call Comp?

"Calling Number" passed to remaining conferee when the conferencing phone drops out?

"Calling Name" passed to remaining conferee when the conferencing phone drops out?

"Connected Number" updated on Orig. Caller phone display when a conferee drops out?

"Connected Name" updated on Orig. Caller phone display when a conferee drops out?

Notes

Phone C to Phone A, Phone A conf Phone B

Yes

(A Drops out) Yes

(A Drops out) Yes

(A Drops out) No

(A Drops out) No

Phone C to Phone A, Phone C conf Phone D

Yes

(C Drops out) No

(C Drops out) No

(D Drops out) No

(D Drops out) No

Phone A to Phone C, Phone C conf Phone D

Yes

(C Drops out) No

(C Drops out) No

(C Drops out) No

(C Drops out) No

Phone A to Phone C, Phone A conf Phone B

Yes

(A Drops out) No

(A Drops out) No

(B Drops out) No

(B Drops out) No

Table 5  Call Forward (Local)

Calls Made

Call Comp?

Original "Calling Number" passed to Final Dest.?

Original "Calling Name" passed to Final Dest.?

Forwarding "Called Number" passed to Final Dest.?

Forwarding "Called Name" passed to Final Dest.?

Final dest. "Connected Number" updated at orig. side?

Final dest. "Connected Name" updated at orig. side?

Notes

Phone C to Phone A fwd to Phone B

Yes

Yes

No

No

No

No

No

Phone A to Phone C fwd to Phone D

Yes

Yes

Yes

No

No

No

No

Calls Made	Call Comp?	"Calling Number" Passed to Final Destination?	"Calling Name" Passed to Final Destination?	"Called Number" Passed to Orig. Side?	"Called Name" Passed to Orig. Side?	Notes
Phone A to Phone C	Yes	Yes	Yes	No	No	¹
Phone C to Phone A	Yes	Yes	No	Yes	No

Calls Made	Call Comp?	Orig. "Calling Number" displayed on Final Dest. phone?	Orig. "Calling Name" displayed on Final Dest. phone?	"Called Number" display on Orig. phone updated after transfer?	"Called Name" display on Orig. phone updated after transfer?	Notes
Phone C to Phone A Xfr to Phone B	Yes	Yes	No	No	No
Phone A to Phone C Xfr to Phone D	Yes	Yes	Yes	No	No

Calls Made	Call Comp?	"Calling Number" passed to remaining conferee when the conferencing phone drops out?	"Calling Name" passed to remaining conferee when the conferencing phone drops out?	"Connected Number" updated on Orig. Caller phone display when a conferee drops out?	"Connected Name" updated on Orig. Caller phone display when a conferee drops out?
Phone C to Phone A, Phone A conf Phone B	Yes	(A Drops out) Yes	(A Drops out) Yes	(A Drops out) No	(A Drops out) No
Phone C to Phone A, Phone C conf Phone D	Yes	(C Drops out) No	(C Drops out) No	(D Drops out) No	(D Drops out) No
Phone A to Phone C, Phone C conf Phone D	Yes	(C Drops out) No	(C Drops out) No	(C Drops out) No	(C Drops out) No
Phone A to Phone C, Phone A conf Phone B	Yes	(A Drops out) No	(A Drops out) No	(B Drops out) No	(B Drops out) No

Calls Made	Call Comp?	Original "Calling Number" passed to Final Dest.?	Original "Calling Name" passed to Final Dest.?	Forwarding "Called Number" passed to Final Dest.?	Forwarding "Called Name" passed to Final Dest.?	Final dest. "Connected Number" updated at orig. side?	Final dest. "Connected Name" updated at orig. side?	Notes
Phone C to Phone A fwd to Phone B	Yes	Yes	No	No	No	No	No
Phone A to Phone C fwd to Phone D	Yes	Yes	Yes	No	No	No	No