Table of Contents

Platforms Supported
What Is a Feature Pack?
Using Cisco Feature Packs

Product Numbers
Cisco Feature Pack and Memory Descriptions
Cisco IOS Release 11.2(11)P Feature Sets
Upgrading Cisco 2500 Memory

Loading Cisco IOS Release 11.2 Software on CiscoPro Routers
Installation Tips

Recovering From a Connection Error
Restoring the Startup Configuration
Helpful Hints

Installing the Router Software Using a TFTP Server Application
Related Documentation
Cisco Connection Online

Release Notes for Cisco IOS Release 11.2(11) Software Feature Packs for Cisco 2500 Series Routers

January 26, 1998

These release notes describe the Cisco Internetwork Operating System (Cisco IOS) Release 11.2(11)P feature packs for Cisco 2500 series routers. This document contains the following sections:

• Platforms Supported
  
  
• What Is a Feature Pack?
  
  
• Using Cisco Feature Packs
  
  
• Loading Cisco IOS Release 11.2 Software on CiscoPro Routers
  
  
• Installation Tips
  
  
• Installing the Router Software Using a TFTP Server Application
  
  
• Related Documentation
  
  
• Cisco Connection Online
  
  

Platforms Supported

The RSL supports the following Cisco 2500 series routers:

• CiscoPro CPA2501, CPA2502, CPA2503, CPA2504, CPA2505, CPA2507, CPA2509, CPA2511, CPA2513, CPA2514, CPA2516, CPA2520, CPA2521, CPA2522, CPA2523, and CPA2524
  
  
• Cisco 2501, 2502, 2503, 2504, 2505, 2507, 2509, AS2509-RJ, 2510, 2511, AS2511-RJ, 2512, 2513, 2514, 2515, 2516, 2520, 2521, 2522, 2523, 2524, and 2525
  
  

What Is a Feature Pack?

The heart of a Cisco IOS software feature pack is a CD-ROM that contains a software image and the Router Software Loader (RSL), a Windows 95 application that loads the image onto the access router or server. Each Cisco IOS Release 11.2 feature pack CD contains one feature set. The CD booklet, Getting Started with the Router Software Loader, explains how to use the RSL to install the router software. Users who cannot use the RSL can load images by following the instructions in the "Installing the Router Software Using a TFTP Server Application" section of this document.

Each Cisco IOS Release 11.2 software feature pack box contains the following:

• CD-ROM with the following software:
  
  
• Feature set software image that includes bundled modem firmware
  
  
• The RSL program (a Windows 95 application)
  
  
• A Trivial File Transfer Protocol (TFTP) server application (for Windows 95 only)
  
  
• Instruction booklet for using the RSL
  
  
• Release notes (this document), which includes alternatives to using the RSL for loading software images onto a router
  
  
• Software license—for using Cisco software in-object code form on a single access server or router
  
  
• Cisco Documentation CD-ROM, which contains all Cisco IOS software documentation
  
  

Before running the RSL, read the section, "Installation Tips". If you are loading software on a preconfigured router, you should save the router configuration file on your PC before beginning the download process, as described in the CD booklet Getting Started with the Router Software Loader.

Using Cisco Feature Packs

The tables in the following sections describe the Cisco feature packs. Use these tables to perform the following tasks before loading a software image onto a router:

1. Use Table 1 in the section "Product Numbers" to identify your software image.

2. Use Table 2 in the section "Cisco Feature Pack and Memory Descriptions" to identify your feature pack and the memory required for your feature set, based on the image you run.

3. Use Table 3 and Table 4 in the section "Cisco IOS Release 11.2(11)P Feature Sets" to identify which features are supported for a feature set on a specific platform.

4. Check the memory required for your feature set against Table 5 in the section "Upgrading Cisco 2500 Memory" to determine the factory-default memory on the router and the available memory upgrades.

Product Numbers

Table 1 lists the Cisco product numbers for the supported feature packs.

Cisco Feature Pack and Memory Descriptions

Table 2 identifies each feature pack as specified on the router software CD-ROM label, describes the feature sets in each feature pack, and lists the following: UNIX and DOS filenames of the images, router platform on which each feature set runs, and memory requirements for each feature set.

Cisco IOS Release 11.2(11)P Feature Sets

Table 3 and Table 4 list Cisco IOS software feature sets available in Cisco IOS Release 11.2(11)P.
These features are available in specific features sets on specific platforms.

Table 3 and Table 4 use these feature set matrix symbols to identify features:

Cisco IOS images with 40-bit Data Encryption Standard (DES) support may legally be distributed to any party eligible to receive Cisco IOS software. 40-bit DES is not a cryptographically strong solution and should not be used to protect sensitive data.

Cisco IOS images with 56-bit DES are subject to International Traffic in Arms Regulations (ITAR) controls and have a limited distribution. Images to be installed outside the U.S. require an export license. Customer orders may be denied or subject to delay because of U.S. government regulations. Contact your sales representative or distributor for more information, or send e-mail to export@cisco.com.

Upgrading Cisco 2500 Memory

Table 5 describes the memory delivered by default and the available memory upgrades.

Loading Cisco IOS Release 11.2 Software on CiscoPro Routers

The RSL has an upgrade utility to permanently modify a CiscoPro router so that it accepts Cisco IOS Release 11.2 software images. The utility changes the router SysObjectID Simple Network Management Protocol (SNMP) MIB value (used for network management) to that of a Cisco router. The software banner also changes and no longer identifies the router as a CiscoPro product.

The upgrade utility must be located in the Images directory. If it is not, the upgrade utility informs you that the image is not present. The Cisco 2500 series upgrade utility filename is cpa25-upgrade-l.112-3.P.

Installation Tips

This section describes some solutions to problems you might encounter when using the RSL. These solutions are additions to RSL online help.

Recovering From a Connection Error

Try increasing the Short Timeout value in the Options dialog box if you receive the following message when trying to connect to the router:

This connection recovery method is particularly applicable when you are connecting to one of the following devices:

• A router that has a large configuration file.
  
  
• A Cisco AS5200. Note that a Cisco AS5200 requires up to 45 seconds to write a configuration to nonvolatile random-access memory (NVRAM) due to the number of interfaces that must be checked during this process. Increase the Short Timeout value to 60 seconds.
  
  

Restoring the Startup Configuration

In some cases, the RSL is unable to restore the startup configuration. If this happens, take the following steps:

Step 1   Ensure that all cables are properly attached to both the router and the PC.

Step 2   Restart the RSL, and connect by using the Preconfigured router option.

Step 3   When asked if you want to overwrite the existing startup configuration file, choose no.

Step 4   When asked if you want to continue, choose yes.

Step 5   When the router is connected, select Download Router Configuration in the Router Software Loader dialog box.

Step 6   Select the appropriate file, and click the radio button beside Copy configuration to the router nonvolatile memory.

The router should now contain the startup configuration it had before the initial RSL connection. You can now exit the RSL.

Helpful Hints

The following information about RSL operations can help you with the installation process:

• If you have added any static entries to the PC Address Resolution Protocol (ARP) table, one of them might be deleted by the RSL. You need to manually re-enter this entry into the PC ARP table.
  
  
• If the router running configuration at connection time is not the same as its startup configuration, the exact configuration is not restored. Any changes that you have made since the last time a copy running-config startup-config or write memory command was entered are lost.
  
  
• The RSL restores the router startup configuration, but some running configuration commands are not restored. To restore the exact running configuration, reboot the router. The following interface configuration commands are not restored to the running configuration: no shutdown, no ringspeed, and media-type aui.
  
  

Installing the Router Software Using a TFTP Server Application

Use this TFTP server application method as an alternative to using the RSL to install the router software from the CD-ROM. You can perform this procedure using a PC (running Microsoft Windows 95 or Microsoft Windows 3.1), a Macintosh, or a UNIX system. You can use either the copy tftp flash or copy rcp flash command to download the router software to the router.

First obtain a TFTP application or a remote copy protocol (rcp) application to set up your computer as a TFTP server or an rcp server. Use the RSL or the TFTP server included on the feature pack CD-ROM to install the router software only if you are using a PC running Windows 95. For other operating systems, a number of TFTP or rcp applications are available from independent software vendors or available as shareware from public sources on the World Wide Web.

Step 1   Install any TFTP server application on the PC. (A PC application is included on the feature pack CD-ROM for Microsoft Windows 95 only.)

Step 2   Launch the TFTP server application on the PC, usually by double-clicking the application icon or its .exe filename.

Step 3   Set up the PC as a TFTP server by using the TFTP server application setup or configuration facility.

Most TFTP server applications include a setup facility that allows you to specify the PC as a server. For example, from the TFTP menu of one application, you can select Settings to display a panel that includes a checkbox beside the word Server. To configure the local PC as a server, click this checkbox.

The TFTP server also allows the selection of a "root" directory. You must select the directory in which the Cisco IOS files reside, for example, d:\cpswinst\images.

Step 4   Establish a console session from your local PC (which is now configured as a TFTP server) to the Cisco router by using one of these methods:

• Connect the PC com port to the router console port.
  
  

  This is the recommended method.When you reload the router with the new image in Step 25, you remain connected to the router. (If you use Telnet, you lose connection to the router.)

• Establish a Telnet session from the PC to the router.

  Caution Make sure your PC is set up to communicate with the 10BaseT Ethernet port on the router.

  
  
  

Step 5   Connect your PC Ethernet port to the corresponding router LAN port. Use the 10BaseT crossover cable to connect to an Ethernet port. Use straight-through cables if you are connecting via a 10BaseT hub or a 100BaseT hub.

---

Note We recommend that you back up the router configuration before upgrading the router software.

---

Step 6   Enter the following commands to set the configuration register to 0x2101 and reload to the bootstrap image:

---

Note If you are upgrading a CiscoPro CPA2500 series router running from an image in Flash memory, the router reloads to ROM monitor mode because of an interaction between the Flash Load Helper and the cpa2500-upgrade-l.112-3.P image.

---

Step 7   Enter yes in response to the prompt asking if the system configuration has been modified:

Step 8   If the password prompt appears, enter the password.

Step 9   At the router prompt, enter enable and then the password:

Step 10   If you are not upgrading a CiscoPro CPA2500 router, skip to Step 19.

Step 11   At the router prompt, enter the following command to copy the router upgrade utility from the PC CD-ROM drive to the router:

Router(boot)# copy tftp flash

---

Note If you are using rcp, enter copy rcp flash instead.

---

Step 12   When prompted, enter the IP address of your PC, as in the following example:

Address or name of remote host [255.255.255.255]? 131.108.1.1

This is the IP address of your local PC, not the router. (Note that you can obtain your PC IP address from the DOS prompt in the windows directory by entering winipcfg, as follows: C:\WINDOWS> winipcfg.)

Step 13   When prompted, enter the filename of the image to be copied to the router as in the following example:

Source file name? cpa2500-upgrade-l.112-3.P

---

Note The upgrade image file on the Feature Pack CD has a long filename (cpa2500-upgrade-l.112-3.P); note that DOS displays it in 8.3 format as cpa2500~1.P. The upgrade utility is a special file, not a Cisco IOS runtime image.

---

Step 14   In response to the following prompt, enter the destination filename, and press Enter.

Destination file name [cpa2500-upgrade-l.112-3.P]? cpa2500-upgrade-l.112-3.P

(This is the name of the image file on the router, not the full pathname of the image on the PC CD-ROM.)

During the transfer process, messages indicate that the software has accessed the file you have specified and is loading it.

If the file is not found, check the following:

• The filename is correct.
  
  
• The TFTP server is enabled.
  
  
• The correct root directory is selected.
  
  
• There is IP connectivity between the router and TFTP server.
  
  

If the file is still not found, create a temporary directory called C:\temp and copy the CiscoPro upgrade file into the directory. Select the C:\temp directory as the root directory.

Step 15   Enter yes in response to the prompt asking if you want to erase the existing image in the router Flash memory before copying the new one:

Erase flash device before writing? [confirm] yes

The entire copying process takes several minutes and differs from network to network. The exclamation point (!) indicates that the copy process is taking place. Each exclamation point indicates that ten packets have been transferred successfully. If you see three or more periods (...), the transfer might fail. If the transfer fails, check IP connectivity between the router and TFTP server by using the ping command.

Step 16   Enter the reload command to reload the router:

Router(boot)# reload

Do not save the configuration.

After reload is complete, your CiscoPro router has been upgraded to a Cisco Enterprise router. Because the original Cisco IOS image that resided in Flash memory was erased during the upgrade process, the router should now be running in bootstrap mode.

Step 17   If the password prompt appears, enter the password.

Step 18   At the router prompt, enter enable and then the password:

Step 19   At the router prompt, enter the following command to copy the new software image from the PC CD-ROM drive to the router:

Router(boot)(config)# copy tftp flash

In the next series of steps, you download the Cisco IOS Release 11.2 images that you want installed on your router.

Step 20   When prompted, enter the IP address of your PC, as in the following example:

Address or name of remote host [255.255.255.255]? 131.108.1.1

This is the IP address of your local PC, not that of the router.

Step 21   When prompted, enter the filename of the Cisco IOS Release 11.2 image to be copied to the router, as in the following example:

This example specifies the DOS image name of the IP feature set for Cisco 2500 series routers (as shown in Table 2 in the section, "Cisco Feature Pack and Memory Descriptions").

Step 22   In response to the prompt, enter the destination UNIX image filename, and press Enter.

This is the name of the image file on the router, not the full pathname of the image on the CD-ROM attached to the PC. Refer to Table 2 in the section, "Cisco Feature Pack and Memory Descriptions" for the UNIX image filename.

During the transfer process, the software displays messages indicating that it has accessed the file you have specified and is loading it.

Step 23   Enter yes in response to the prompt asking if you want to erase the existing image copy resident in the router Flash memory before copying the new one.

Erase flash device before writing? [confirm] yes

The entire copying process takes several minutes and differs from network to network.

The exclamation point (!) indicates that the copy process is taking place. Each exclamation point (!) indicates that ten packets have been transferred successfully. A checksum verification of the image occurs after the image is written to Flash memory.

Step 24   Enter the following commands to reset the configuration register to 0x2102.

Step 25   Enter the reload command to reload the router:

After reload is complete, the router should be running the required Cisco IOS image. Use the show version command to verify.

Related Documentation

For a list of documentation related to the Cisco 2500, refer to the Release Notes for the 2500 Series for Cisco IOS Release 11.2P. Release notes and other Cisco documentation are on the Cisco Documentation CD-ROM and at Cisco Connection Online (CCO) on the World Wide Web:

• On the Documentation CD-ROM, go to Cisco Product Documentation, select Cisco IOS Software Configuration, and then select Cisco IOS Release 11.2.
  
  
• On CCO, go to http://www.cisco.com/, click on Software and Support, and select Documentation. Next, select Documentation, go to Cisco IOS Software Configuration, and then click on Cisco IOS Release 11.2.
  
  

Online documentation for Release 11.2 includes:

• Release Notes
  
  
• Feature Guides including new features for Cisco IOS Release 11.2(10)P
  
  
• Configuration Guides and Command References
  
  
• Command Summary
  
  
• System Error Messages
  
  
• MIB User Quick Reference
  
  
• Debug Command Reference
  
  
• Caveats
  
  

For Cisco IOS Release 11.2, the Cisco IOS documentation set consists of eight documentation modules. Each documentation module has a configuration guide, a command reference, and five supporting documents.

The books and chapter topics are as follows:

If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar, select Documentation, and click Enter the feedback form. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.

Cisco Connection Online

Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.

CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.

You can access CCO in the following ways:

• WWW:  http://www.cisco.com
  
  
• WWW:  http://www-europe.cisco.com
  
  
• WWW:  http://www-china.cisco.com
  
  
• Telnet:  cco.cisco.com
  
  
• Modem:  From North America, 408 526-8070; from Europe, 33 1 64 46 40 82. Use the following terminal settings: VT100 emulation; databits: 8; parity: none; stop bits: 1; and connection rates up to 28.8 kbps.
  
  

For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.

Posted: Tue Dec 17 19:33:51 PST 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.