Chapter 11, TL1 Reference

11 TL1 Reference

11.1 Overview

This section lists TL1 alarms, commands, and autonomous messages supported by the Cisco ONS 15454. For more information about TL1, refer to Telcordia document GR833-CORE, Network Maintenance: Network Element and Transport Surveillance Messages.

11.2 Craft Interface

The TCC/TCC+ has two built-in interface ports for accessing the ONS 15454. With one RJ-45 craft interface browser LAN connection you can access the system using a standard browser interface. While using the browser interface, you can perform local and remote Operations, Administration, Maintenance and Provisioning (OAM&P) functions and open a VT100 emulation window to enter TL1 commands. If a browser is not available, you can access the system using a nine- pin RS-232 port. The RS-232 port supports VT100 emulation such that TL1 commands may be entered directly without a browser.

Refer to the "Craft Interface Installation" section on page 1-31 for detailed installation procedures. Refer to the "Connecting to the ONS 15454 with TL1 Terminals" section on page 3-9 for information on terminal setup.

11.3 TL1 Access using Telnet

To access the ONS 15454 TL1 commands using a Telnet session over a craft interface or a Local Access Network (LAN) connection (TCC/TCC+ front panel or backplane pins), you must use port number 2361. At a command prompt, start the Telnet session by typing:

telnet <Node IP Address> 2361 [Enter]

11.4 Alarms

This section lists TL1 alarms supported by the ONS 15454. Each alarm list includes a description, service affect criteria, and severity. Refer to Chapter 9, "CTC Alarms," for fault recovery procedures. The following alarm types are listed:

•Equipment Alarms

•SONET Optical Carrier, level n (OC-N) Alarms

•Digital Signal, level 1 (DS-1) Alarms

•Digital Signal, level 3 (DS-3) Alarms

•Synchronous Transport Signal (STS) Alarms

•Virtual Tributary (VT) Termination Alarms

•Building Integrated Timing Supply (BITS) Alarms

•Network Element (NE) Synchronous Reference Alarms

11.4.1 Equipment Alarms

Table 11-1 Equipment Alarms
EQPT alarm	Card/Mode	Severity (Active/ Standby)	SA/NSA (Active/ Standby)	Description
INT	all any mode	CR/MN	SA/NSA	Internal board Failure
IMPROPRMVL	all any mode	CR/MN	SA/NSA	Board is provisioned and has been unplugged
MEA	all any mode	MN/MN	NSA/NSA	Mismatch in between the physical equipment type and the provisioned equipment type
FAILTOSW- PATH	TCC,TCC+,XC,DS-3 any mode	MJ/MN	SA/NSA	Failure to perform an equipment protection switch
POWERFAIL	all any mode	CR/MN	NSA/NSA	Power Failure on the node
MANUAL	TCC,TCC+,XC,DS-3 any mode	MN/MN	NSA/NSA	Operator Manual switch severity active
FORCED	TCC,TCC+,XC,DS-3 any mode	MN/MN	NSA/NSA	Operator Force switch severity active
DIAGFAIL	all any mode	CR/MN	NSA/NSA	Equipment diagnostic failure
HITEMP	TCC,TCC+ Any mode	CR/CR	NSA/NSA	Excessive temperature - operating still maintaining normal operations
FAN	all any mode	CR/MI	NSA/NSA	Fan operation failure
PWRRESTART	all any mode	MI/MI	NSA/NSA	Power restart
AUTORESET	all any mode	MI/MI	NSA/NSA	Automatic reset
MANRESET	TCC,TCC+ any mode	MI/MI	NSA/NSA	Manual reset
INIT	TCC,TCC+ any mod	MI/MI	NSA/NSA	Initialization initiated
SWTRANSFER	TCC,TCC+ any mod	MI/MI	NSA/NSA	Software download in progress
CONTBUS-A-X	IO,XC any mode	MJ/MN	NSA/NSA	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot X
CONTBUS-A-8	IO,XC any mode	MJ/MN	NSA/NSA	Main processor on the TCC/TCC+ card in Slot 7 has lost communication with the coprocessor on the second TCC/TCC+ card in Slot 11
CONTBUS-B-X	IO,XC any mode	MJ/MN	NSA/NSA	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot X
CONTBUS-B-8	IO,XC any mode	MJ/MN	NSA/NSA	Main processor on the TCC/TCC+ card in Slot 11 has lost communication with the processor on the second TCC/TCC+ card in Slot 7
CTNEQPT-PBXPROT	I/O, XC/XCVT	CR/MN	SA/NSA	Failure of the main payload between the XC/XCVT card in Slot 10 and the reporting I/O card in Slot X
CTNEQPT-PBXWORK	I/O, XC/XCVT	CR/MN	SA/NSA	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot X

11.4.2 OC-N Alarms

Table 11-2 OC-N Alarms
OC-n alarm	Card/Mode	Severity (Active/ Standby)	SA/NSA (Active/ Standby)	Description
LOS	OC-3, OC-12, OC-48 any mode	CR/MN	SA/NSA	Loss of Signal alarm
LOF	OC-3,OC-12, OC-48 any mode	CR/MN	SA/NSA	Loss of Frame alarm
AIS-L	OC-3,OC-12, OC-48 any mode	MN/MN	SA/NSA	Alarm Indication Signal Line alarm
RFI-L	OC-3,OC-12, OC-48 any mode	MN/MN	NSA/NSA	Remote Failure Indication Line alarm
SFBER	OC-3,OC-12, OC-48, any mode	CR/MN	SA/NSA	Signal fail error rate alarm
SDBER	OC-3,OC-12, OC-48 any mode	MN/MN	SA/NSA	Signal degrade error rate alarm
FAILTOSW-RNG	OC-3,OC-12, OC-48 2F BLSR mode	MJ/MN	SA/NSA	Failure to perform a two-fiber BLSR ring switch
FAILTOSW-SPAN	OC-3,OC-12, OC-48 linear mode	MJ/MN	SA/NSA	Failure to perform a Linear APS 1+1 switch
MANUAL-REQ	OC-3,OC-12, OC-482 2F BLSR mode	MN/MN	NSA/NSA	Manual Ring Switch Severity active
FORCED-REQ	OC-3,OC-12, OC-48 2F BLSR mode	MN/MN	SA/NSA	Force Ring Switch Severity active
LOCKOUTOFPR- RING	OC-3,OC-12, OC-482 2F BLSR mode	MN/MN	SA/NSA	Lockout of Protection Channel Switch Severity active
MANUAL-SPAN	OC-3,OC-12, OC-48 linear mode	MN/MN	NSA/NSA	Manual Span Switch Severity active
FORCED-SPAN	OC-3,OC-12, OC-482 linear mode	MN/MN	SA/NSA	Force Span switch Severity active
LOCKOUT-SPAN	OC-3,OC-12, OC-48 linear mode	MN/MN	SA/NSA	Lockout Span Switch Severity active
APSB	OC-3,OC-12, OC-48 linear mode	MJ/MN	SA/NSA	Automatic Protection Switching (APS) byte failure
APSCM	OC-3,OC-12, OC-48 linear mode	MJ/MN	SA/NSA	APS Channel Mismatch failure
APSMM	OC-3,OC-12, OC-48 linear mode	MJ/MN	SA/NSA	APS Mode Mismatch failure
APSFERPFAIL		MN/MN	NSA/NSA	APS channel far-end protection line failure
EOC		MJ/MN	NSA/NSA	Data communication channel failure
SQUELCH	OC-12,OC-48 2F BLSR mode	MJ/MN	SA/NSA	Squelching in progress
INCON	OC-12,OC-48 2F BLSR mode	MJ/MN	SA/NSA	Inconsistent APS code
APSCIMP	OC-12,OC-48 2F BLSR mode	MJ/MN	SA/NSA	Improper SONET Automatic Protect Switch code
NODEMIS	OC-12,OC-48 2F BLSR mode	MJ/MN	SA/NSA	Node Id mismatch failure
DFLTK	OC-12,OC-48 2F BLSR mode	MN/MN	NSA/NSA	Default K byte transmitted
CONNLOS	TCC/TCC+ 2F BLSR mode	MJ/MN	NSA/NSA	Inter-node connectivity lost in two-fiber BLSR configuration
ALS		CR/MN	NSA/NSA	Automatic laser shut down
LPBKTERMIN	OC-3,OC-12, OC-48 any mode	MJ/MI	SA/NSA	Terminal loopback active
LPBKFACILITY	OC-3, OC-12, OC-48 any mode	MJ/MI	SA/NSA	Facility loopback active

11.4.3 DS-3 Alarms

Table 11-3 DS-3 Alarms
DS-3 alarm	Card/Mode	Severity (Active)	SA/NSA (Active)	Description
PEERMISSM	DS-3 any mode	MJ	SA	Peer state mismatch
LOS	DS-3 any mode	CR	SA	Loss of signal alarm
LPBK	DS-3 any mode	MJ	SA	Loopback active
IDLE	DS-3 any mode	MJ	SA	DS-3 idle condition
RAI	DS-3 any mode	MN	SA	Remote alarm indication
DS3MANTERM- LPBK	DS-3 any mode	MJ	SA	Loopback terminal
DS3MANFAC LPBK	DS-3 any mode	MJ	SA	Loopback facility
DS3FELPBK	DS-3 any mode	MJ	SA	Loopback due to Far-End Alarm Condition (FEAC) command
DS2FELPBK	DS-3 any mode	MJ	SA	DS-2 loopback command sent to far-end
DS1FELPBK	DS-3 any mode	MJ	SA	DS- 1 loopback due to FEAC command
DS3FELPBK	DS-3 any mode	MJ	SA	DS-3 loopback due to FEAC command
DS3FELPBKCMD	DS-3 any mode	MJ	SA	DS-3 loopback command sent to far-end
FE-EQPT-FAIL-SA	DS-3 any mode	MJ	SA	Far-end DS-3 equipment fail service-affecting
FE-LOS	DS-3 any mode	MJ	SA	Far-end loss of signal
FE-LOF	DS-3 any mode	MJ	SA	Far-end loss of frame
FE-AIS	DS-3 any mode	MJ	SA	Far-end alarm indication signal
FE-IDLE	DS-3 any mode	MJ	SA	Far-end idle
FE-EQPT-NSA	DS-3 any mode	MJ	SA	Far-end DS-3 equipment fail non-service affecting
DS3FECMNEQPT FAIL	DS-3 any mode	MJ	SA	Far-end common equipment fail non-service affecting
FE-DS1-MULTI LOS	DS3XM any mode	MJ	SA	Far-end multiple DS-1 LOS detected on DS-3
DS1FEEQPTFAIL SA	DS3XM any mode	MJ	SA	Far-end DS-1 equipment fail service-affecting
FE-SD1-SNGLLOS	DS3XM any mode	MJ	SA	DS-1 far-end single DS-1 LOS
DS1FEEQPT	DS3XM any mode	MJ	SA	Far-end DS-1 equipment failure service-affecting

11.4.4 DS-1 Alarms

Table 11-4 DS-1 Alarms
DS-1 alarm	Card/Mode	Severity (Active/ Standby)	SA/NSA (Active/ Standby)	Description
LOS	DS-1 any mode	MJ/None	SA/None	Loss of signal alarm
AIS	DS-1 any mode	MJ/None	SA/None	Alarm indication signal alarm
LOF	DS-1 any mode	MJ/None	SA/None	Loss of frame alarm
RAI	DS-1 any mode	MN/None	SA/None	Remote alarm indication alarm
TERMLPBK	DS-1 any mode	MJ/None	SA/None	Terminal loopback active
FACLPBK	DS-1 any mode	MJ/None	SA/None	Facility loopback active
ELECTRICAL INTERFACE MISSING - TX	DS-1 any mode	MJ/MN	NSA/NSA	Facility Termination equipment - Transmitter missing
ELECTRICAL INTERFACE MISSING - RX	DS-1 any mode	MJ/MN	NSA/NSA	Facility Termination equipment - Receiver missing
ELECTRICAL INTERFACE FAILURE - TX	DS-1 any mode	MJ/MN	NSA/NSA	Transmit Failure
FELPBK	DS-1 any mode	MJ/None	SA/None	DS-1 loopback due to FEAC command
FELPBKCMD	DS-1 any mode	MJ/None	SA/None	DS-1 loopback command sent to far-end

11.4.5 STS Alarms

Table 11-5 STS Alarms
STS Mon alarm	Card/Mode	Severity (Active/ Standby)	SA/NSA (Active/ Standby)	Description
AIS-P	STS Monitor any mode	MJ/MN	SA/NSA	Alarm Indication Signal alarm
LOP	STS Monitor any mode	MJ/MN	SA/NSA	Loss of Pointer alarm
CONCAT	STS Monitor any mode	MJ/MN	SA/NSA	STS concatenation alarm
UNEQ-P	STS Termination on DS-3 card any mode	MJ/MN	SA/NSA	Path Unequipped alarm
SFBER	STS Termination on DS-3 card any mode	MJ/MN	SA/NSA	Path Signal Fail bit error rate alarm
SDBER	STS Termination on DS-3 card any mode	MN/MN	SA/NSA	Path Signal Degrade bit error rate alarm
RFI	STS Termination on DS-3 card any mode	MN/MN	SA/NSA	Path Remote Failure Indication alarm
SLMF	STS Termination on DS-3 card any mode	MN/MN	SA/NSA	Signal Label Mismatch alarm
PDI-P		MN/MN	SA/NSA	Payload Defect Indication Path
PLM-P		MN/MN	SA/NSA	Payload Label Mismatch Path
FAILTOSW	STS Termination on DS-3 card any mode	MJ/MN	NSA/NSA	Fail to switch to protection
MANUAL	STS Termination on DS-3 card any mode	MN/MN	NSA/NSA	Manual switch of working facility equipment to protection
FORCED	STS Termination on DS-3 card any mode	MN/MN	NSA/NSA	Working facility/equipment forced to switch to protection

11.4.6 VT Termination Alarms

Table 11-6 VT Termination Alarms
VT Term alarm	Card/Mode	Severity (Active/ Standby)	SA/NSA (Active/ Standby)	Description
LOP	STS Monitor any mode	MJ/MN	SA/NSA	Loss of pointer alarm
AIS	VT Termination on DS-1 card any mode	MJ/MN	SA/NSA	VT Alarm Indication Signal alarm
UNEQP	VT Termination on DS-1 card any mode	MJ/MN	SA/NSA	VT Unequipped alarm
RFI	VT Termination on DS-1 card any mode	MN/MN	SA/NSA	VT Remote Failure Indication alarm
PLM	VT Termination on DS-1 card any mode	MN/MN	SA/NSA	VT Payload Label Mismatch alarm
SFBER		MJ/MN	SA/NSA	BER threshold passed for signal failure
SDBER		MJ/MN	SA/NSA	BER threshold passed for signal degrade

11.4.7 BITS Alarms

Table 11-7 Bits Alarms
BITS alarm	Card/Mode	Severity (Active/ Standby)	SA/NSA (Active/ Standby)	Description
LOS	Bits on TCC/TCC+ card any mode	MJ/MN	SA/NSA	Loss of Signal alarm
LOF	Bits on TCC/TCC+ card any mode	MJ/MN	SA/NSA	Loss of Frame alarm
AIS	Bits on TCC/TCC+ card any mode	MJ/MN	SA/NSA	Alarm Indication Signal alarm

11.4.8 Network Element Synch Ref Alarms

Table 11-8 Synch Ref Alarms
neSynchRef alarm	Card/Mode	Severity (Active/ Standby)	SA/NSA	Description
SYNCPRI	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Primary Synchronization reference failure alarm
SYNCSEC	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Secondary Synchronization reference failure alarm
SYNCTHIRD	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Third Synchronization reference failure alarm
HLDOVRSYNC	neSynchRef on TCC/TCC+ card any mode	MJ/MN	SA/NSA	Holdover Synchronization alarm
FRNGSYNC	neSynchRef on TCC/TCC+ card any mode	MJ/MN	SA/NSA	Free Run Synchronization alarm
MANUAL	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Operator-initiated synchronization switch
FASTSTART	Fast start Synch node	No	No Alarm	Fast Start Synchronization alarm
MANSWTOPRI	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Synchronization switch to primary reference
MANSWTOSEC	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Synchronization switch to second reference
MANSWTOTHID	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Synchronization switch to third reference
SWTOPRI	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Synchronization switch to primary reference
SWTOSEC	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Synchronization switch to second reference
SWTOTHIRD	neSynchRef on TCC/TCC+ card any mode	MN/MN	NSA/NSA	Synchronization switch to third reference

11.5 Autonomous Messages

The autonomous TL1 messages are included in the TL1 Command Description section, and the messages are listed alphabetically. Figure 11-1 shows the autonomous alarm message format. Autonomous Message Tag (ATAG) is used for message sequencing. The number is incremented by one for each autonomous message sent by the ONS 15454. The ONS 15454 uses whole numbers 0000 to 9999.

Figure 11-1 Autonomous Alarm Message Format

11.6 Performance Monitoring

Performance information is continuously monitored and stored in individual Performance Monitoring (PM) registers. This information can be retrieved upon request or when a preset threshold is exceeded. lists PM Statistics by board.

11.6.1 Performance Monitoring Statistics

Table 11-9 PM Statistics
PM Statistics by Board	Special Qualifications	Source	DS-1	DS-3	DS-3 XM	OC-3/12/48	EC-1
Sonet Section Stats
CV-S	(not supported yet)	B1
ES-S	(not supported yet)	B1
SES-S	(not supported yet)	B1
SEFS-S		B1				X	X
Sonet Line Stats
CV-L		B2				X	X
ES-L		B2				X	X
SES-L						X	X
UAS-L						X	X
FC-L						X	X
PSC						X
PSD						X
STS PJ	Non-terminated STS only	H1, H2
PPJC-PDET	Positive detected at input					X	X
NPJC-PDET	Negative detected at input					X	X
PPJC-PGEN	Positive generated					X	X
NPJC-PGEN	Negative generated					X	X
Far End
CV-L FE		K2				X	X
ES-L FE		K2				X	X
SES-L FE		K2				X	X
UAS-L FE		K2				X	X
FC-L FE		K2				X	X
Sonet Path Stats
CV-P		B3	X	X	X
ES-P			X	X	X
SES-P			X	X	X
UAS-P			X	X	X
FC-P
VT PJ
Far End	Supplied by XCON
CV-P FE	From XCON					X
ES-P FE	From XCON					X
SES-P FE	From XCON					X
UAS-P FE	From XCON					X
FC-P FE
VT Path Stats	VT terminated circuits only
CV-V			X		X
ES-V			X		X
SES-V			X		X
UAS-V			X		X
FC-V
Far End
CV-V FE			X		X
ES-V FE			X		X
SES-V FE			X		X
UAS-V FE			X		X
FC-V FE
DS-n Stats
DS-n Line
CV-L		X	X	X	X
ES-L		X	X	X	X
LOSS-L					X
SES-L		X	X	X	X
DS-3 Path
P Bit Stats	M13 & C Bit Framing
AISS-P					X
CVP-0					X
ESP-P					X
SASP-P					X
SESP-P					X
UASP-P					X
CP Bit Stats	C Bit Framing ONLY
CVCP-P					X
ESCP-P					X
SASCP-P					X
SESCP-P					X
UASCP-P					X
Far End
CVCP-P FE					X
ESCP-P FE					X
SASCP-P FE					X
SESCP-P FE					X
UASCP-P FE					X
DS-1 Path
CV-P RX			X
AISS-P RX			X		X
ES-P RX			X		X
SAS-P RX			X		X
SES-P RX			X		X
UAS-P RX			X		X
CV-P TX			X		X
AISS-P TX			X		X
ES-P TX			X		X
SAS-P TX			X		X
SES-P TX			X		X
UAS-P TX			X		X

11.7 TL1 Command Syntax

TL1 commands conform to the following syntax:

a:b:c::d:e: ... z;

where:

"a" is the Command Code

"b" is the Target Identifier (TID)

"c" is the Access Identifier (AID) or the User Identifier (UID)

"d" is the Correlation Tag (CTAG)

"e: ... z;" are the other positions required for various commands

The TID, AID, and CTAG route and control the TL1 command. Other parameters provide additional messages required to complete the action requested by the command.

The TID is a unique name given to each system when it is installed. The name identifies the particular NE (in this case, the ONS 15454), to which each command is directed. Each TID can have a maximum of 20 alpha-numeric characters. To establish the TID for a ONS 15454 node, use the Network Element Name option of the Network Element Configuration menu.

The AID is an access code used to identify and address specific objects within the ONS 15454. These objects include individual pieces of equipment, transport spans, access tributaries, and other objects.

The CTAG is a unique identifier given to each input command by the operator. When the ONS 15454 system responds to a specific command, it includes the command's CTAG in the reply. This eliminates discrepancies about what response corresponds to what command. Valid CTAG values include strings of up to six characters comprised of identifiers (alphanumeric, beginning with a letter) or decimal numerals (a string of decimal digits with an optional non-trailing ".").

11.8 TL1 Command Privilege Map

The following table specifies command access privileges.

Table 11-10 Command Access
Command	Superuser	Provision	Maintenance	Retrieve
DLT-USER-SECU	X
ED-DAT	X
ED-USER-SECU	X
ENT-USER-SECU	X
SET-TOD	X	X
DLT--	X	X
ED--	X	X
ENT--	X	X
SET--	X	X
INIT--	X	X	X
OPR--	X	X	X
RLS--	X	X	X
RMV--	X	X	X
RST--	X	X	X
SW--	X	X	X
ALW--	X	X	X	X
INH--	X	X	X	X
REPT * *	X	X	X	X
RTRV--	X	X	X	X
CANC--	X	X	X	X
ACT--	X	X	X	X
ED-PD	X	X	X	X

User security levels also limit the amount of time a user can leave the system idle before the TL1 session is locked to prevent unauthorized users from making changes. Higher security levels have shorter idle times. shows security levels and their idle times

Table 11-11 Security Idle Times
Security Level	Idle Time
Retrieve	Unlimited
Maintenance	60 minutes
Provision	30 minutes
Superuser	15 minutes

11.9 TL1 Command List

11.9.1 Cross Connect

DLT-CRS-<STS_PATH>

DLT-CRS-VT1

ED-CRS-<STS_PATH>

ED-CRS-VT1

ENT-CRS-<STS_PATH>

ENT-CRS-VT1

RTRV-CRS-<STS_PATH>

RTRV-CRS-VT1

11.9.2 Environment

REPT ALM ENV

RTRV-ALM-ENV

11.9.3 Equipment

DLT-EQPT

DLT-FFP-EQPT

ED-FFP-EQPT

ENT-EQPT

ENT-FFP-EQPT

OPR-PROTNSW-EQPT

REPT ALM EQPT

REPT EVT EQPT

RLS-PROTNSW-EQPT

RTRV-ALM-EQPT

RTRV-COND-EQPT

RTRV-EQPT

RTRV-FFP-EQPT

SW-DX-EQPT

11.9.4 Facility

RMV-<MOD2>

RST-<MOD2>

11.9.5 Facility Protection

DLT-FFP-<OCN_TYPE>

ED-FFP-<OCN_TYPE>

ENT-FFP-<OCN_TYPE>

RTRV-FFP-<OCN_TYPE>

11.9.6 Fault

REPT ALM <MOD2ALM>

REPT ALM BITS

REPT EVT <MOD2ALM>

RTRV-ALM-<MOD2ALM>

RTRV-ALM-ALL

RTRV-ALM-BITS

RTRV-COND-<MOD2ALM>

RTRV-COND-ALL

RTRV-COND-BITS

11.9.7 Log

RTRV-LOG

11.9.8 Performance

INIT-REG-<MOD2>

RTRV-PM-<MOD2>

RTRV-TH-<MOD2>

SET-TH-<MOD2>

11.9.9 Security

DLT-USER-SECU

ED-PID

ED-USER-SECU

ENT-USER-SECU

11.9.10 Switch

OPR-PROTNSW-<OCN_TYPE>

RLS-PROTNSW-<OCN_TYPE>

11.9.11 Synchronization

ED-SYNCN

REPT ALM SYNCN

REPT EVT SYNCN

RTRV-ALM-SYNCN

RTRV-COND-SYNCN

RTRV-SYNCN

11.9.12 System

ACT-USER

ALW-MSG-ALL

CANC-USER

ED-DAT

INH-MSG-ALL

INIT-SYS

RTRV-HDR

11.9.13 Testing

OPR-LPBK-<OCN_TYPE>

OPR-LPBK-DS1

OPR-LPBK-EC1

OPR-LPBK-T1

OPR-LPBK-T3

RLS-LPBK-<OCN_TYPE>

RLS-LPBK-DS1

RLS-LPBK-EC1

RLS-LPBK-T1

RLS-LPBK-T3

11.9.14 Other

DLT-<MODE2>

ED-<OCN_TYPE>

ED-<STS_PATH>

ED-BITS

ED-EC1

ED-NE

ED-T1

ED-T3

ENT-<MOD2>

OPR-UPGRADE

RTRV-<OCN_TYPE>

RTRV-<STS_PATH>

RTRV-BITS

RTRV-EC1

RTRV-INV

RTRV-NE

RTRV-T1

RTRV-T3

RTRV-TOD

SET-TOD

11.10 TL1 Command Index

Table 11-12 Command Index
Command	Group	Page Number
ACT-USER	System	ACT-USER: Activate User
ALW-MSG-ALL	System	ALW-MSG-ALL: Allow Message All
CANC-USER	System	CANC-USER: Cancel User
DLT-<MODE2>	Other	DLT-<MOD2>: Delete (DS-1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
DLT-CRS-<STS_PATH>	Cross Connect	DLT-CRS-<STS_PATH>: Delete Cross Connect (STS1, STS3C, STS12C)
DLT-CRS-VT1	Cross Connect	DLT-CRS-VT1: Delete Cross Connect Virtual Tributary
DLT-EQPT	Equipment	DLT-EQPT: Delete Equipment
DLT-FFP-<OCN_TYPE>	Facility Protection	DLT-FFP-<OCN_TYPE>: Delete Facilities Protection Group (OC3, OC12, OC48)
DLT-FFP-EQPT	Equipment	DLT-FFP-EQPT: Delete Facilities Protection Equipment
DLT-USER-SECU	Security	DLT-USER-SECU: Delete User Security
ED-<OCN_TYPE>	Other	ED-<OCN_TYPE>: Edit (OC3, OC12, OC48)
ED-<STS_PATH>	Other	ED-<STS_PATH>: Edit (STS1, STS3C, STS12C)
ED-BITS	Other	ED-BITS: Edit Building Integrated Timing Supply
ED-CRS-<STS_PATH>	Cross Connect	ED-CRS-<STS_PATH>: Edit Cross Connect (STS1, STS3C, STS12C)
ED-CRS-VT1	Cross Connect	ED-CRS-VT1: Edit Cross Connect Virtual Tributary
ED-DAT	System	ED-DAT: Edit Date and Time
ED-EC1	Other	ED-EC1: Edit Electrical Carrier Level 1
ED-FFP-<OCN_TYPE>	Facility Protection	ED-FFP-<OCN_TYPE>: Edit Facilities Protection Group (OC3, OC12, OC48)
ED-FFP-EQPT	Equipment	ED-FFP-EQPT: Edit Equipment Protection
ED-NE	Other	ED-NE: Edit Network Element
ED-PID	Security	ED-PID: Edit Private Identifier
ED-SYNCN	Synchronization	ED-SYNCN: Edit Synchronization
ED-T1	Other	ED-T1: Edit T1
ED-T3	Other	ED-T3: Edit T3
ED-USER-SECU	Security	ED-USER-SECU: Edit User Security
ENT-<MOD2>	Other	ENT-<MOD2>: Enter (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
ENT-CRS-<STS_PATH>	Other	ENT-CRS-<STS_PATH>: Enter Cross Connect (STS1, STS3C, STS12C)
ENT-CRS-VT1	Other	ENT-CRS-VT1: Enter Cross Connect Virtual Tributary
ENT-EQPT	Equipment	ENT-EQPT: Enter Equipment
ENT-FFP-<OCN_TYPE>	Facility Protection	ENT-FFP-<OCN_TYPE>: Enter Facilities Protection Group (OC3, OC12, OC48)
ENT-FFP-EQPT	Equipment	ENT-FFP-EQPT: Enter Equipment Protection
ENT-USER-SECU	Security	ENT-USER-SECU: Enter User Security
INH-MSG-ALL	System	INH-MSG-ALL: Inhibit Message All
INIT-REG-<MOD2>	Performance	INIT-REG-<MOD2>: Initialize Register (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
INIT-SYS	System	INIT-SYS: Initialize System
OPR-LPBK-<OCN_TYPE>	Testing	OPR-LPBK-<OCN_TYPE>: Operate Loopback (OC3, OC12, OC48)
OPR-LPBK-DS1	Testing	OPR-LPBK-DS1: Operate Loopback Digital Signal Level 1
OPR-LPBK-EC1	Testing	OPR-LPBK-EC1: Operate Loopback Electrical Carrier Level 1
OPR-LPBK-T1	Testing	OPR-LPBK-T1: Operate Loopback T1
OPR-LPBK-T3	Testing	OPR-LPBK-T3: Operate Loopback T3
OPR-PROTNSW-<OCN_TYPE>	Switch	OPR-PROTNSW-<OCN_TYPE>: Operate Protection Switch (OC3, OC12, OC48)
OPR-PROTNSW-EQPT	Equipment	OPR-PROTNSW-EQPT: Operate Protection Switch Equipment
OPR-UPGRADE	Other	OPR-UPGRADE: Operate Upgrade
REPT ALM <MOD2ALM>	Fault	REPT ALM <MOD2>: Report Alarm (DS1, E100, E1000, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
REPT ALM BITS	Fault	REPT ALM BITS: Report Alarm Building Integrated Timing Supply
REPT ALM ENV	Environment	REPT ALM ENV: Report Alarm Environment
REPT ALM EQPT	Equipment	REPT ALM EQPT: Report Alarm Equipment
REPT ALM SYNCN	Synchronization	REPT ALM SYNCN: Report Alarm Synchronization
REPT EVT <MOD2ALM>	Fault	REPT EVT <MOD2ALM>: Report Event (DS1, E100, E1000, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
REPT EVT EQPT	Equipment	REPT EVT EQPT: Report Event Equipment
REPT EVT SYNCN	Synchronization	REPT EVT SYNCN: Report Event Synchronization
RLS-LPBK-<OCN_TYPE>	Testing	RLS-LPBK-<OCN_TYPE>: Release Loopback (OC3, OC12, OC48)
RLS-LPBK-DS1	Testing	RLS-LPBK-DS1: Release Loopback Digital Signal Level 1
RLS-LPBK-EC1	Testing	RLS-LPBK-EC1: Release Loopback Electrical Carrier Level 1
RLS-LPBK-T1	Testing	RLS-LPBK-T1: Release Loopback T1 Facility
RLS-LPBK-T3	Testing	RLS-LPBK-T3: Release Loopback T3 Facility
RLS-PROTNSW-<OCN_TYPE>	Switch	RLS-PROTNSW-<OCN_TYPE>: Release Protection Switch (OC3, OC12, OC48)
RLS-PROTNSW-EQPT	Equipment	RLS-PROTNSW-EQPT: Release Protection Switch Equipment
RMV-<MOD2>	Facility	RMV-<MOD2>: Remove (DS1, EC1,OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
RST-<MOD2>	Facility	RST-<MOD2>: Restore (DS1, EC1,OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
RTRV-<OCN_TYPE>	Other	RTRV-<OCN_TYPE>: Retrieve (OC3, OC12, OC48)
RTRV-<STS_PATH>	Other	RTRV-<STS_PATH>: Retrieve (STS1, STS3C, STS12C)
RTRV-ALM-<MOD2ALM>	Fault	RTRV-ALM-<MOD2ALM>:Retrieve Alarm (DS1, E100, E1000, EC1, OC12, OC3, OC48, STS1, STS12C, STS3C, STS48C, T1, T3, VT1)
RTRV-ALM-ALL	Fault	RTRV-ALM-ALL: Retrieve Alarm All
RTRV-ALM-BITS	Fault	RTRV-BITS: Retrieve Building Integrated Timing Supply
RTRV-ALM-ENV	Environment	RTRV-ALM-ENV: Retrieve Alarm Environment
RTRV-ALM-EQPT	Equipment	RTRV-ALM-EQPT: Retrieve Alarm Equipment
RTRV-ALM-SYNCN	Synchronization	RTRV-ALM-SYNCN: Retrieve Alarm Synchronization
RTRV-BITS	Other	RTRV-BITS: Retrieve Building Integrated Timing Supply
RTRV-COND-<MOD2ALM>	Fault	RTRV-COND-<MOD2ALM>: Retrieve Condition (DS1, E100, E1000, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
RTRV-COND-ALL	Fault	RTRV-COND-ALL: Retrieve Condition All
RTRV-COND-BITS	Fault	RTRV-COND-BITS: Retrieve Condition Building Integrated Timing Supply
RTRV-COND-EQPT	Equipment	RTRV-COND-EQPT: Retrieve Condition Equipment
RTRV-COND-SYNCN	Synchronization	RTRV-COND-SYNCN: Retrieve Condition Synchronization
RTRV-CRS-<STS_PATH>	Cross Connect	RTRV-CRS-<STS_PATH>: Retrieve Cross Connect (STS1, STS3C STS12C)
RTRV-CRS-VT1	Cross Connect	RTRV-CRS-VT1: Retrieve Cross Connect Virtual Tributary
RTRV-EC1	Other	RTRV-EC1: Retrieve Electrical Carrier Level 1
RTRV-EQPT	Equipment	RTRV-EQPT: Retrieve Equipment
RTRV-FFP-<OCN_TYPE>	Facility Protection	RTRV-FFP-<OCN_TYPE>: Retrieve Facilities Protection Group (OC3, OC12, OC48)
RTRV-FFP-EQPT	Equipment	RTRV-FFP-EQPT: Retrieve Facilities Protection Group Equipment
RTRV-HDR	System	RTRV-HDR: Retrieve Header
RTRV-INV	Other	RTRV-INV: Retrieve Inventory
RTRV-LOG	Log	RTRV-LOG: Retrieve Log
RTRV-NE	Other	RTRV-NE: Retrieve Network Element
RTRV-PM-<MOD2>	Performance	RTRV-PM-<MOD2>: Retrieve Performance (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
RTRV-SYNCN	Synchronization	RTRV-SYNCN: Retrieve SYNCN
RTRV-T1	Other	RTRV-T1: Retrieve T1
RTRV-T3	Other	RTRV-T3: Retrieve T3
RTRV-TH-<MOD2>	Performance	RTRV-TH-<MOD2>: Retrieve Threshold (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
RTRV-TOD	Other	RTRV-TOD: Retrieve Time of Day
SET-TH-<MOD2>	Performance	SET-TH-<MOD2>: Set Threshold (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)
SET-TOD	Other	SET-TOD: Set Time of Day
SW-DX-EQPT	Equipment	SW-DX-EQPT: Switch DX Equipment

11.11 TL1 Command Description

This section lists TL1 commands supported by the ONS 15454. Each listing includes a description, input format, input parameters (instructions within a command), and input example. The descriptions are alphabetical according to the first alpha character of the command string.

Note The TL1 input command string size should equal and less than 1023 characters from either a TL1 telnet session or CTC. Any TL1 input string larger than 1023 characters will cause the active TCC to reset.

Note TL1 commands not entered correctly are not completed.

11.11.1 ACT-USER: Activate User

This command allows you to log in to the Network Element (NE).


Section	Description
Category	System
Security	Read Only
Related Messages	ALW-MSG-ALL CANC-USER DLT-USER-SECU ED-DAT ED-PID ED-USER-SECU ENT-USER-SECU INH-MSG-ALL INIT-SYS RTRV-HDR
Input Format	ACT-USER:[TID]:<userid>:[CTAG]::<passwd>; where: •userid identifies the user to the system and is a String •passwd is the user's private password and is a String
Example	Input ACT-USER:PETALUMA:TERRI:100::MYPASSWD;
Errors	This message generates all the default errors

11.11.2 ALW-MSG-ALL: Allow Message All

This command instructs the NE to enter a mode in which all automatic messages are transmitted.


Section	Description
Category	System
Security	N/A
Related Messages	ACT-USER CANC-USER ED-DAT INH-MSG-ALL INIT-SYS RTRV-HDR
Input Format	ALW-MSG-ALL:[TID]::[CTAG]::,,;
Example	Input ALW-MSG-ALL:PETALUMA::549::,,;
Errors	This message generates all the default errors

11.11.3 CANC-USER: Cancel User

This command logs a user off of the NE.


Section	Description
Category	System
Security	Read Only
Related Messages	ACT-USER ALW-MSG-ALL DLT-USER-SECU ED-DAT ED-PID ED-USER-SECU ENT-USER-SECU INH-MSG-ALL INIT-SYS RTRV-HDR
Input Format	CANC-USER:[TID]:[<userid>]:[CTAG]; where: •userid identifies the user to the system and is a String
Example	Input CANC-USER:PETALUMA:TERRI:101;
Errors	This message generates all the default errors

11.11.4 DLT-<MOD2>: Delete (DS-1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command deletes the line or facility by putting it out of service.

Note The DLT- does not support STS1, STS3C, STS12C, STS48C, VT1, and DS1 modifiers in Release 2.2.1.


Section	Description
Category	Other
Security	N/A
Related Messages	N/A
Input Format	DLT-<MOD2>:[TID]:<aid>:[CTAG]; where: •aid is the AID ALL
Example	Input DLT-EC1:CISCO:FAC-1-1:123;
Errors	This message generates all the default errors

11.11.5 DLT-CRS-<STS_PATH>: Delete Cross Connect (STS1, STS3C, STS12C)

This command deletes a cross-connect between STS paths. STS paths are specified using their STS AID.


Section	Description
Category	Cross Connect
Security	N/A
Related Messages	DLT-CRS-VT1 ED-CRS-<STS_PATH> ED-CRS-VT1 ENT-CRS-<STS_PATH> ENT-CRS-VT1 RTRV-CRS-<STS_PATH> RTRV-CRS-VT1
Input Format	DLT-CRS-<STS_PATH>:[TID]:<from>,<to>:[CTAG]:::; where: •from is the source aid of the cross sts connection and is the AID sts •to is the destination aid of the crs sts connection and is the AID sts
Example	Input DLT-CRS-STS12C:VINBURG:STS-1-1, STS-12-1:102:::;
Errors	This message generates all the default errors

11.11.6 DLT-CRS-VT1: Delete Cross Connect Virtual Tributary

This command deletes the VT1 cross connects.


Section	Description
Category	Cross Connect
Security	N/A
Related Messages	DLT-CRS-<STS_PATH> ED-CRS-<STS_PATH> ED-CRS-VT1 ENT-CRS-<STS_PATH> ENT-CRS-VT1 RTRV-CRS-<STS_PATH> RTRV-CRS-VT1
Input Format	DLT-CRS-VT1:[TID]:<from>,<to>:[CTAG]:::; where: •from is the source aid of the vt connection and is the AID vt1_5 •to is the destination aid of the crs vt connection and is the AID vt1_5
Example	Input DLT-CRS-VT1:CISCO:VT1-2-3-1,VT1-4-4-1:1234:::;
Errors	This message generates all the default errors

11.11.7 DLT-EQPT: Delete Equipment

This command deletes a card from the NE. It removes the card type and attributes that were entered for a particular slot. If any facilities are assigned, they are also deleted as long as they do not contain any cross-connect end-points, the cards are not in a protection group and they are not in SDCC termination. If any of the above descriptions exist, the command will be denied.


Section	Description
Category	Equipment
Security	N/A
Related Messages	DLT-FFP-EQPT RLS-PROTNSW-EQPT ED-FFP-EQPT RTRV-ALM-EQPT ENT-EQPT RTRV-COND-EQPT ENT-FFP-EQPT RTRV-EQPT OPR-PROTNSW-EQPT RTRV-FFP-EQPT REPT ALM EQPT SW-DX-EQPT REPT EVT EQPT
Input Format	DLT-EQPT:[TID]:<eqpt_aid>:[CTAG]; where: •equip_aid is the AID eqpt
Example	Input DLT-EQPT:SONOMA:SLOT-1:104;
Errors	This message generates all the default errors

11.11.8 DLT-FFP-<OCN_TYPE>: Delete Facilities Protection Group (OC3, OC12, OC48)

This command deletes a linear protected group on optical cards.


Section	Description
Category	Facility Protection
Security	N/A
Related Messages	N/A
Input Format	DLT-FFP-<OCN_TYPE>:[TID]:<work>,<protect>:[CTAG]; where: •work is the working equipment and the AID facility •protect is the protection equipment and the AID facility
Example	Input DLT-FFP-OC3:PETALUMA:FAC-2-1,FAC-1-1:1;
Errors	This message generates all the default errors

11.11.9 DLT-FFP-EQPT: Delete Facilities Protection Equipment

This command deletes an equipment protection group.


Section	Description
Category	Equipment
Security	N/A
Related Messages	DLT-EQPT RLS-PROTNSW-EQPT ED-FFP-EQPT RTRV-ALM-EQPT ENT-EQPT RTRV-COND-EQPT ENT-FFP-EQPT RTRV-EQPT OPR-PROTNSW-EQPT RTRV-FFP-EQPT REPT ALM EQPT SW-DX-EQPT REPT EVT EQPT
Input Format	DLT-FFP-EQPT:[TID]:<work>,<protect>:[CTAG]; where: •work is the AID eqpt •protect is the AID eqpt
Example	Input DLT-FFP-EQPT:PETALUMA:SLOT-2,SLOT-1:1;
Errors	This message generates all the default errors

11.11.10 DLT-USER-SECU: Delete User Security

This command removes a user and can only be used by an administrator. The AID block contains the user identifier. If this command is executed while the user is logged on, the current session for that user continues. Once the user logs out, the same userid cannot be used to log in again. This command is defined in TR-835.


Section	Description
Category	Security
Security	Admin
Related Messages	ACT-USER CANC-USER ED-PID ED-USER-SECU ENT-USER-SECU
Input Format	DLT-USER-SECU:[TID]:<username>:[CTAG]; where: •username is a String
Example	Input DLT-USER-SECU:CISCO:UID:123;
Errors	This message generates all the default errors

11.11.11 ED-<OCN_TYPE>: Edit (OC3, OC12, OC48)

This command modifies the attributes (i.e. service parameters) and state of an OC-N facility. Allowable states for a facility are Out of Service (OOS) and In Service (IS).


Section	Description
Category	Other
Security	Read/Write
Related Messages	N/A
Input Format	ED-<OCN_TYPE>:[TID]:<fac_aid>:[CTAG]::[SDCC=<sdcc>], [PJMON=<pjmon>],[SFBER=<sfber>],[SDBER=<sdber>], [MODE=<opticalMode>]:[<pst>]:; Note If changing the pst field only, use the following Input Format: ED-<OCN_TYPE>:[TID]:<fac_aid>:[CTAG]::[<pst>]:; where: •fac_aid is the AID facility •sdcc enables the Section DCC for this facility and is of type SDCC_MODE •pjmon is the number of the STS facility to monitor for pointer justifications pjmon is an Integer •sfber is of type SF_BER •sdber is of type SD_BER •opticalMode is of type OPTICAL_MODE •pst is the card primary state and is of type PST
Example	Input ED-OC48:PENNGROVE:FAC-6-1:114::SDCC=Y,PJMON=48,SFBER=1E-4, SDBER=1E-6, MODE=SONET:IS:;
Errors	This message generates all the default errors

11.11.12 ED-<STS_PATH>: Edit (STS1, STS3C, STS12C)

This command is used to modify the attributes associated with an STS path.


Section	Description
Category	Other
Security	Read/Write
Related Messages	N/A
Input Format	ED-<STS_PATH>:[TID]:<sts_aid>:[CTAG]::[SFBER=[<sfber>], [SDBER=<sdber>]::; where: •sts_aid is the AID sts •sfber is of type SF_BER •sdber is of type SD_BER
Example	Input ED-STS1:FERNDALE:STS-2-4:115::SFBER=1E-3,SDBER=1E-5::;
Errors	This message generates all the default errors

11.11.13 ED-BITS: Edit Building Integrated Timing Supply

This command modifies BITS reference attributes.


Section	Description
Category	Other
Security	Read/Write
Related Messages	N/A
Input Format	ED-BITS:[TID]:<bits_aid>:[CTAG]::[LNCDE=<line_code>], [FRMF=<frame_format>]:<pst>:; where: •bits_aid is the AID bits •line_code is the BITS line code and is of type LINE_CODE •frame_format is the BITS frame format and is of type FRAME_FORMAT •pst is the BITS state and is of type PST
Example	Input ED-BITS:SONOMA:BITS-2:779::LNCDE=AMI,FRMF=ESF:IS;
Errors	This message generates all the default errors

11.11.14 ED-CRS-<STS_PATH>: Edit Cross Connect (STS1, STS3C, STS12C)

This command modifies attributes of an STS-level cross-connect. Under certain circumstances, you may change the cross-connect type (e.g. from 1WAY to 2WAY).


Section	Description
Category	Cross Connect
Security	Read/Write
Related Messages	DLT-CRS-<STS_PATH> DLT-CRS-VT1 ED-CRS-VT1 ENT-CRS-<STS_PATH> ENT-CRS-VT1 RTRV-CRS-<STS_PATH> RTRV-CRS-VT1
Input Format	ED-CRS-<STS_PATH>:[TID]:<from>,<dst>:[CTAG]::<cct>::; where: •from is the source aid of the cross sts connection and is the AID sts •dst is the AID sts •cct is the cross connection type and is of type CCT
Example	Input ED-CRS-STS3C:KENWOOD:STS-6-4,STS-12-7:108::2WAY::;
Errors	This message generates all the default errors

11.11.15 ED-CRS-VT1: Edit Cross Connect Virtual Tributary

This command edits the VT1.5 cross-connect.


Section	Description
Category	Cross Connect
Security	Read/Write
Related Messages	DLT-CRS-<STS_PATH> DLT-CRS-VT1 ED-CRS-<STS_PATH> ENT-CRS-<STS_PATH> ENT-CRS-VT1 RTRV-CRS-<STS_PATH> RTRV-CRS-VT1
Input Format	ED-CRS-VT1:[TID]:<from>,<to>:[CTAG]::<cct>::; where: •from is the AID vtl_5 •to is the AID vtl_5 •cct is the cross connection type and is of type CCT
Example	Input ED-CRS-VT1:CISCO:VT1-2-1-1,VT1-4-1-1:1234::1WAY::;
Errors	This message generates all the default errors

11.11.16 ED-DAT: Edit Date and Time

This command edits the date and time.


Section	Description
Category	System
Security	Read/Write
Related Messages	ACT-USER ALW-MSG-ALL CANC-USER INH-MSG-ALL INIT-SYS RTRV-HDR
Input Format	ED-DAT:[TID]::[CTAG]::[<date>],[<time>]; where: •date is the date field YYYY-MM-DD or YY-MM-DD; date is a String •time is the time field HH-MM-SS, the hours 0..24; time is a String
Example	Input ED-DAT:TID::1234::99-12-21,14-35-15;
Errors	This message generates all the default errors

11.11.17 ED-EC1: Edit Electrical Carrier Level 1

This command edits EC-1 facilities. This command will edit the properties of an EC-1 card port.


Section	Description
Category	Other
Security	Read/Write
Related Messages	N/A
Input Format	ED-EC1:[TID]:<fac>:[CTAG]::[PJMON=<pjmon>][,][LBO=<lbo>]:<pst>:; where: •fac is the facility aid. fac is the AID facility •pjmon is the SONET pointer number 0 or 1 and is an Integer •lbo is the line buildout and is of type E_LBO •pst is the port state and is of type PST
Example	Input ED-EC1:CISCO:FAC-1-1:123::PJMON=0,LBO=0-225:IS:;
Errors	This message generates all the default errors

11.11.18 ED-FFP-<OCN_TYPE>: Edit Facilities Protection Group (OC3, OC12, OC48)

This command edits the optical facility protection.


Section	Description
Category	Facility Protection
Security	Read/Write
Related Messages	N/A
Input Format	ED-FFP-<OCN_TYPE>:[TID]:<facility>:[CTAG]::[NAME=<name>], [RVTT=<revertiveType>],[RVTM=<revertiveTime>],[BSWM=<bswMode>]; where: •facility is the facility aid and is the AID facility •name is the protection name and is a String •revertiveType is of type REVERTIVE_TYPE •revertiveTime is of type REVERTIVE_TIME •bswMode specifies if it is a bidirectional switch mode and is of type ON_OFF
Example	Input ED-FFP-OC3:PETALUMA:FAC-1-1:1::NAME=PROT_NAME,RVTT=R, RVTM=1.0,BSWM=OFF;
Errors	This message generates all the default errors

11.11.19 ED-FFP-EQPT: Edit Equipment Protection

This command edits an equipment protection group.


Section	Description
Category	Equipment
Security	Read/Write
Related Messages	DLT-EQPT RLS-PROTNSW-EQPT DLT-FFP-EQPT RTRV-ALM-EQPT ENT-EQPT RTRV-COND-EQPT ENT-FFP-EQPT RTRV-EQPT OPR-PROTNSW-EQPT RTRV-FFP-EQPT REPT ALM EQPT SW-DX-EQPT REPT EVT EQPT
Input Format	ED-FFP-EQPT:[TID]:<eqpt>:[CTAG]::[NAME=<name>], [RVTT=<revertiveType>],[RVTM=<revertiveTime>]; where: •eqpt is the equipment aid and is the AID eqpt •name is the name of the group and is a String •revertiveType is of type REVERTIVE_TYPE •revertiveTime is of type REVERTIVE_TIME
Example	Input ED-FFP-EQPT:PETALUMA:SLOT-1:1::NAME=PROT_NAME,RVTT=R, RVTM=1.0;
Errors	This message generates all the default errors

11.11.20 ED-NE: Edit Network Element

This command modifies the attributes of the NE system such as changing the node's identity (e.g. IP address), external interfaces (e.g. LAN ports), and major modes of operation (e.g. SONET vs. SDH).


Section	Description
Category	Other
Security	Read/Write
Related Messages	N/A
Input Format	ED-NE:[TID]::[CTAG]:::[NAME=<name>],[IPADDR=<ipaddr>], [IPMASK=<ipmask>],[DEFRTR=<defrtr>],[TMMD=<timing_mode>], [SSMG=<sync_gen>],[NSQL=<sync_quality_level>]; where: •name is the System Identifier (SID/TID) of the NE and must be 20 characters or less; name is a String •ipaddr is the IP address of the NE on the local LAN and is a String •ipmask is the IP Mask used to identify the sub-net on which the NE resides; ipmask is a String •defrtr is the IP address of the default router and is a String •timing_mode is of type TIMING_MODE •sync_gen is of type SYNC_GENERATION •sync_quality_level is of type SYNC_QUALITY_LEVEL
Example	Input ED-NE:LKVLL::111:::NAME=LAKEVILLE,IPADDR=192.168.100.52, IPMASK=255.255.255.0,DEFRTR=192.168.100.1,TMMD=LINE, SSMG=GEN1,NSQL=ABOVE-PRS;
Errors	This message generates all the default errors

11.11.21 ED-PID: Edit Private Identifier

This command allows a user to change their own password. Other user identification and access changes may only be made by a superuser. This command is defined in TR-835.

Note The password cannot be null. It will be echoed as clear text as the message is parsed and only after the complete message is entered and terminated.

Note The password should not appear in the TL1 log on the NE.


Section	Description
Category	Security
Security	Read/Write
Related Messages	ACT-USER CANC-USER DLT-USER-SECU ED-USER-SECU ENT-USER-SECU
Input Format	ED-PID:[TID]:<username>:[CTAG]::<oldPassword>,<newPassword>; where: •username is a String •oldPassword is a String •newPassword is a String
Example	Input ED-PID:CISCO:UID:123::OLD_PASSWORD,NEW_PASSWORD;
Errors	This message generates all the default errors

11.11.22 ED-SYNCN: Edit Synchronization

This command modifies the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock. For each clock, up to three synchronization sources may be specified (for example, PRIMARY, SECOND, THIRD).


Section	Description
Category	Synchronization
Security	Read/Write
Related Messages	REPT ALM SYNCN REPT EVT SYNCN RTRV-ALM-SYNCN RTRV-COND-SYNCN RTRV-SYNCN
Input Format	ED-SYNCN:[TID]:<sync_aid>:[CTAG]:::[PRIMARY=<primary>], [SECOND=<second>],[THIRD=<third>]:; where: •sync_aid is the synchronization reference to be modified; sync_aid is the AID sync_ref and is listable •primary is the AID syn_src •second is the AID syn_src •third is the AID syn_src
Example	Input ED-SYNCN:BOYES:SYNC-NE:112:::PRIMARY=INTERNAL, SECOND=INTERNAL,THIRD=INTERNAL:;
Errors	This message generates all the default errors

11.11.23 ED-T1: Edit T1

This command modifies the attributes related to a DS-1 port.


Section	Description
Category	Other
Security	Read/Write
Related Messages	ED-T3 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-T1 RLS-LPBK-T3 RTRV-T1 RTRV-T3
Input Format	ED-T1:[TID]:<tl1_aid>:[CTAG]::[ID=<id>],[LNCDE=<line_code>], [FRMF=<frame_format>],[LBO=<line_buildout>]:[<pst>]:; where: •t1_aid is the AID facility •id is a String •line_code is the port line code and is of type LINE_CODE •frame_format is of type FRAME_FORMAT •line_buildout is the port line buildout and is of type LINE_BUILDOUT •pst is of type PST
Example	Input ED-T1:CISCO:FAC-1-1:1223::ID=CISCO,LNCDE=AMI,FRMF=ESF, LBO=0-131:IS:;
Errors	This message generates all the default errors

11.11.24 ED-T3: Edit T3

This command edits a DS-3 and DS-3 transmux card.


Section	Description
Category	Other
Security	Read/Write
Related Messages	ED-T1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-T1 RLS-LPBK-T3 RTRV-T1 RTRV-T3
Input Format	ED-T3:[TID]:<facility>:[CTAG]::[LNTYPE=<lineType>], [LNCODE=<lineCode>],[LB0=<lbo>][<pst>]; where: •facility is the AID facility •lineType is the port line type and is of type DS_LINE_TYPE •lineCode is the line code and is the lineCode of the DS3XM card; lineCode is of type DS_LINE_CODE •lbo is the circuit line buildout and is of type E_LBO •pst is of type PST
Example	Input ED-T3:CISCO:FAC-1-2:123::LNTYPE=C-BIT,LNCODE=B3ZS,LBO=0-225: IS:;
Errors	This message generates all the default errors

11.11.25 ED-USER-SECU: Edit User Security

This command edits a user's privileges, password, or ID. Only a user with R/W admin privileges may perform this operation. Privilege levels are described in the ENT-USER-SECU: Enter User Security command. This command is defined in TR-835.

Note If the password is changed with this command, the password should be blanked out in the TL1 log.


Section	Description
Category	Security
Security	Admin
Related Messages	ACT-USER CANC-USER DLT-USER-SECU ED-PID ENT-USER-SECU
Input Format	ED-USER-SECU:[TID]:<username>:[CTAG]::[PASSWORD=<password>], [PRIVILEGE=<privilege>]; where: •username is a String •password is a String •privilege is of type PRIVILEGE
Example	Input ED-USER-SECU:CISCO:UID:123::PASSWORD=PASSWORD, PRIVILEGE=MAINT;
Errors	This message generates all the default errors

11.11.26 ENT-<MOD2>: Enter (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command puts a facility or an aid in service.

Note ENT-DS1/STS1/STS3C/STS12C/STS48C/VT1 are not supported in Release 2.2.1.


Section	Description
Category	Other
Security	Admin
Related Messages	N/A
Input Format	ENT-<MOD2>:[TID]:<aid>:[CTAG]; where: •aid is the aid to be put in service and is the AID ALL
Example	Input ENT-OC3:CISCO:FAC-1-1:1243;
Errors	This message generates all the default errors

11.11.27 ENT-CRS-<STS_PATH>: Enter Cross Connect (STS1, STS3C, STS12C)

This command creates an STS cross-connect between two or more STS paths. Rather than create each individual unidirectional connection singularly, this command accepts cross-connection types (CCT) that identify aggregate cross-connects based on their function in the network. To enter a cross-connect, the facilities that support the STS paths must be either in service or out of service assigned. If a cross-connect (XC) card is not present in the system or if the paths have incompatible payload types, the request is denied.


Section	Description
Category	Cross Connect
Security	Admin
Related Messages	DLT-CRS-<STS_PATH> DLT-CRS-VT1 ED-CRS-<STS_PATH> ED-CRS-VT1 ENT-CRS-VT1 RTRV-CRS-<STS_PATH> RTRV-CRS-VT1
Input Format	ENT-CRS-<STS_PATH>:[TID]:<from>,<to>:[CTAG]::<cct>::; where: •from is the source aid of the cross sts connection and is the AID sts •to is the destination aid of the crs sts connection and is the AID sts •cct is the cross connection type and is of type CCT
Example	Input ENT-CRS-STS1:BODEGA:STS-1-5,STS-2-5:116::2WAY::;
Errors	This message generates all the default errors

11.11.28 ENT-CRS-VT1: Enter Cross Connect Virtual Tributary

This command creates a VT1 cross connect.


Section	Description
Category	Cross Connect
Security	Admin
Related Messages	DLT-CRS-<STS_PATH> DLT-CRS-VT1 ED-CRS-<STS_PATH> ED-CRS-VT1 ENT-CRS-<STS_PATH> RTRV-CRS-<STS_PATH}> RTRV-CRS-VT1
Input Format	ENT-CRS-VT1:[TID]:<from>,<to>:[CTAG]::<cct>::; where: •from is the source aid of the cross vt connection and is the AID vt1_5 •to is the destination aid of the crs vt connection and is the AID vt1_5 •cct is the cross connection type and is of type CCT
Example	Input ENT-CRS-VT1:CISCO:VT1-2-3-14,VT1-4-4-12:1234::1WAY::;
Errors	This message generates all the default errors

11.11.29 ENT-EQPT: Enter Equipment

This command enters the card type and attributes for a given equipment slot in the NE. It also automatically enters all facilities supported by the card, assigning default values to all facility and path attributes.


Section	Description
Category	Equipment
Security	Admin
Related Messages	DLT-EQPT RLS-PROTNSW-EQPT DLT-FFP-EQPT RTRV-ALM-EQPT ED-FFP-EQPT RTRV-COND-EQPT ENT-FFP-EQPT RTRV-EQPT OPR-PROTNSW-EQPT RTRV-FFP-EQPT REPT ALM EQPT SW-DX-EQPT REPT EVT EQPT
Input Format	ENT-EQPT:[TID]:<eqpt>:[CTAG]::<eqpt_type>; where: •eqpt is the AID eqpt •eqpt_type is of type EQUIPMENT_TYPE
Example	Input ENT-EQPT:PETALUMA:SLOT-12:118::OC12;
Errors	This message generates all the default errors

11.11.30 ENT-FFP-<OCN_TYPE>: Enter Facilities Protection Group (OC3, OC12, OC48)

This command creates an optical protection.


Section	Description
Category	Facility Protection
Security	Admin
Related Messages	N/A
Input Format	ENT-FFP-<OCN_TYPE>:[TID]:<work>,<protect>:[CTAG]::[NAME=<name>], [RVTM=<rvtm>],[RVTT=<rvtt>],[BSWM=<bswMode>]; where: •work is the working unit aid and is the AID facility •protect is the protection unit aid and is the AID facility •name is the protection name and is a String •rvtm is the revertive mode and is of type REVERTIVE_TYPE •rvtt is the revertive time and of type REVERTIVE_TIME •bswMode specifies if it is bidirectional switch mode and is of type ON_OFF
Example	Input ENT-FFP-OC3:PETALUMA:FAC-2-1,FAC-1-1:1::NAME=PROT_NAME, RVTM=R,RVTT=1.0,BSWM=OFF;
Errors	This message generates all the default errors

11.11.31 ENT-FFP-EQPT: Enter Equipment Protection

This command creates an equipment protection.


Section	Description
Category	Equipment
Security	Admin
Related Messages	DLT-EQPT RLS-PROTNSW-EQPT DLT-FFP-EQPT RTRV-ALM-EQPT ED-FFP-EQPT RTRV-COND-EQPT ENT-EQPT RTRV-EQPT OPR-PROTNSW-EQPT RTRV-FFP-EQPT REPT ALM EQPT SW-DX-EQPT REPT EVT EQPT
Input Format	ENT-FFP-EQPT:[TID]:<work>,<protect>:[CTAG]::PRT=<protectionGroup>, [NAME=<name>],[RVTM=<rvtm>],[RVTT=<rvtt>]; where: •work is the AID eqpt •protect is the AID eqpt •protectionGroup is the protection group 1-1 or 1-N and is of type PROTECTION_GROUP •name is the protection name and is a String •rvtm is the revertive mode and is of type REVERTIVE_TYPE •rvtt is the revertive time and is of type REVERTIVE_TIME
Example	Input ENT-FFP-EQPT:PETALUMA:SLOT-2,SLOT-1:1::PRT=1-1, NAME=PROT_NAME,RVTM=R,RVTT=1.0;
Errors	This message generates all the default errors

11.11.32 ENT-USER-SECU: Enter User Security

This command adds a user account. Only administrators may do this. The AID block contains the user identifier. See .

There are seven security levels defined for the TalonMX. Each user may be configured as possessing 1or more of these seven privileges.

1 Read-Only Alarms: Users possessing this security level can retrieve and receive autonomous alarms.

2 Read-Write Alarms: Users possessing this security level can manage as well as receive/retrieve alarm information.

3 Read-Only Provisioning: Users possessing this security level can retrieve TalonMX provisioning values.

4 Read-Write Provisioning: Users possessing this security level can set/retrieve TalonMX provisioning values.

5 Read-Only Administrative: Users possessing this security level can retrieve TalonMX security settings.

6 Read-Write Administrative: Users possessing this security level can set/retrieve TalonMX security settings.

7 Read-Write Maintenance: Users possessing this security level can perform maintenance functions such as operating/releasing loopbacks.

A superuser will have all privileges shown above.

This command is defined in TR-835.


Section	Description
Category	Security
Security	Admin
Related Messages	ACT-USER CANC-USER DLT-USER-SECU ED-PID ED-USER-SECU
Input Format	ENT-USER-SECU:[TID]:<username>:[CTAG]::<password>,<privilege>; where: •username is a String •password is the user login password and is a String •privilege is the user security level and is of type PRIVILEGE; Superuser=super, Provision=prov, Maintenance=maint, Retrieve=rtrv
Example	Input ENT-USER-SECU:CISCO:UID:123::PSWD,MAINT;
Errors	This message generates all the default errors

11.11.33 INH-MSG-ALL: Inhibit Message All

This command instructs the NE to enter a mode that prevents all automatic messages from being transmitted.


Section	Description
Category	System
Security	N/A
Related Messages	ACT-USER ALW-MSG-ALL CANC-USER ED-DAT INIT-SYS RTRV-HDR
Input Format	INH-MSG-ALL:[TID]::[CTAG]::,,;
Example	Input INH-MSG-ALL:PETALUMA::550::,,;
Errors	This message generates all the default errors

11.11.34 INIT-REG-<MOD2>: Initialize Register (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command initializes the performance monitoring registers.


Section	Description
Category	Performance
Security	Read/Write
Related Messages	RTRV-PM-<MOD2> RTRV-TH-<MOD2> SET-TH-<MOD2>
Input Format	INIT-REG-<MOD2>:[TID]:<aid>:[CTAG]::,,,,<tmpr>,,; where: •aid is the AID facility •tmpr is of type TMPR
Example	Input INIT-REG-OC3:TID:FAC-1-1:1234::,,,,15MIN,,;
Errors	This message generates all the default errors

11.11.35 INIT-SYS: Initialize System

This command instructs the NE to initialize the specified card and its associated subsystem(s). The command supports various levels of restart, called phases, ranging from a warm start to a cold start.

Note In Release 2.2.1 this command only resets equipment. The phase parameter is not supported in this release.


Section	Description
Category	System
Security	Read/Write
Related Messages	ACT-USER ALW-MSG-ALL CANC-USER ED-DAT INH-MSG-ALL RTRV-HDR
Input Format	INIT-SYS:[TID]:<eqpt_aid>:[CTAG]::[<phase>]; where: •eqpt-aid is the AID eqpt •phase is the level of initialization to take place; the higher the number the stronger the reset, A phase=1 is a warm start and A phase=10 is a cold start; phase is an Integer
Example	Input INIT-SYS:HOTWATER:SLOT-1:201::3;
Errors	This message generates all the default errors

11.11.36 OPR-LPBK-<OCN_TYPE>: Operate Loopback (OC3, OC12, OC48)

This command instructs the NE to operate a loopback on a specified OC-N facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	OPR-LPBK-DS1 OPR-LPBK-EC1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-DS1 RLS-LPBK-EC1 RLS-LPBK-T1 RLS-LPBK-T3
Input Format	OPR-LPBK-<OCN_TYPE>:[TID]:<fac_aid>:[CTAG]::,,,,<lpbktype>; where: •fac_aid is the AID facility •lpbktype identifies the type of loopback (Terminal or Facility) to be established and is of type LPBK_TYPE
Example	Input OPR-LPBK-OC3:PTREYES:FAC-5-12:203::,,,FACILITY;
Errors	This message generates all the default errors

11.11.37 OPR-LPBK-DS1: Operate Loopback Digital Signal Level 1

This command operates a DS-1 signal loopback on a DS3XM-6 card.

Note The TERMINAL loopback type is not supported for this command.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	OPR-LPBK-<OCN_TYPE> OPR-LPBK-EC1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-DS1 RLS-LPBK-EC1 RLS-LPBK-T1 RLS-LPBK-T3
Input Format	OPR-LPBK-DS1:[TID]:<ds>:[CTAG]::,,,<lpbkType>; where: •ds is the aid for the DS3XM card on the ds-1 and is the AID ds-1 •lpbkType is the loop back type Note The terminal loop back type is not supported for the DS3XM in Release 2.2.1. lpbkType is of type LPBK_TYPE
Example	Input OPR-LPBK-DS1:PTREYES:DS1-4-2-13:203::,,,FACILITY;
Errors	This message generates all the default errors

11.11.38 OPR-LPBK-EC1: Operate Loopback Electrical Carrier Level 1

This command operates the loopback on an EC-1 facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	OPR-LPBK-<OCN_TYPE> OPR-LPBK-DS1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-DS1 RLS-LPBK-EC1 RLS-LPBK-T1 RLS-LPBK-T3
Input Format	OPR-LPBK-EC1:[TID]:<facility>:[CTAG]::,,,<lpbkType>; where: •facility is the facility aid for the EC-1 and is the AID facility •lpbkType is the loop back type and is of type LPBK_TYPE
Example	Input OPR-LPBK-EC1:PTREYES:FAC-4-2:203::,,,FACILITY;
Errors	This message generates all the default errors

11.11.39 OPR-LPBK-T1: Operate Loopback T1

This command operates the loopback for a DS-1 facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	ED-T1 ED-T3 OPR-LPBK-<OCN_TYPE> OPR-LPBK-DS1 OPR-LPBK-EC1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-DS1 RLS-LPBK-EC1 RLS-LPBK-T1 RLS-LPBK-T3 RTRV-T1 RTRV-T3
Input Format	OPR-LPBK-T1:[TID]:<fac>:[CTAG]::,,,<lpbk_type>; where: •fac is the AID facility •lpbk_type is the loop back type for the DS-1 cards and is of type LPBK_TYPE
Example	Input OPR-LPBK-T1:PTREYES:FAC-4-12:203::,,,FACILITY;
Errors	This message generates all the default errors

11.11.40 OPR-LPBK-T3: Operate Loopback T3

This command instructs the NE to operate a loopback on a specified T3 facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	ED-T1 RLS-LPBK-DS1 ED-T3 RLS-LPBK-EC1 OPR-LPBK-<OCN_TYPE> RLS-LPBK-T1 OPR-LPBK-DS1 RLS-LPBK-T3 OPR-LPBK-EC1 RTRV-T1 OPR-LPBK-T1 RTRV-T3 RLS-LPBK-<OCN_TYPE>
Input Format	OPR-LPBK-T3:[TID]:<fac_aid>:[CTAG]::,,,<lpbktype>; where: •fac_aid is the AID facility •lpbktype identifies the loopback type (Terminal or Facility) to be established and is of type LPBK_TYPE
Example	Input OPR-LPBK-T3:SCHELLVILLE:FAC-2-11:202::,,,TERMINAL;
Errors	This message generates all the default errors

11.11.41 OPR-PROTNSW-<OCN_TYPE>: Operate Protection Switch (OC3, OC12, OC48)

This command instructs the NE to initiate a SONET line protection switch request. User switch requests initiated with this command remain active until they are released via the RLS-PROTNSW-OCN command or are overridden by a higher priority protection switch request.


Section	Description
Category	Switch
Security	Read/Write
Related Messages	N/A
Input Format	OPR-PROTNSW-<OCN_TYPE>:[TID]:<fac_aid>:[CTAG]::<dnField>; where: •fac_aid is the AID facility and is listable •dnField is the switch mode and is of type SWITCH
Example	Input OPR-PROTNSW-OC48:CHICKALUMA:FAC-2-1:204::LOCKOUT;
Errors	This message generates all the default errors

11.11.42 OPR-PROTNSW-EQPT: Operate Protection Switch Equipment

This command initiates a protection switch. The RLS-PROTNSW-EQPT command can be used to release a switch condition.


Section	Description
Category	Equipment
Security	Read/Write
Related Messages	DLT-EQPT RLS-PROTNSW-EQPT DLT-FFP-EQPT RTRV-ALM-EQPT ED-FFP-EQPT RTRV-COND-EQPT ENT-EQPT RTRV-EQPT ENT-FFP-EQPT RTRV-FFP-EQPT REPT ALM EQPT SW-DX-EQPT REPT EVT EQPT
Input Format	OPR-PROTNSW-EQPT:[TID]:<eqpt_aid>:[CTAG]::<sc>; where: •eqpt_aid is the equipment aid and is the AID eqpt •sc is the protection switch mode and is of type PROT_MOD_OP
Example	Input OPR-PROTNSW-EQPT:LASLOMAS:SLOT-1:205::FRCD;
Errors	This message generates all the default errors

11.11.43 OPR-UPGRADE: Operate Upgrade

This command operates upgrades.


Section	Description
Category	Other
Security	Read/Write
Related Messages	N/A
Input Format	OPR-UPGRADE:[TID]:<eqpt_aid>:[CTAG]; where: •eqpt_aid is the AID eqpt
Example	Input OPR-UPGRADE:FOUNTAINGROVE:SLOT-1:204;
Errors	This message generates all the default errors

11.11.44 REPT ALM <MOD2>: Report Alarm (DS1, E100, E1000, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

Reports an alarm condition against a facility or a line.

Note The STS alarms are reported as STS1 alarms.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM BITS RTRV-ALM-BITS REPT ALM ENV RTRV-ALM-ENV REPT ALM EQPT RTRV-ALM-EQPT REPT ALM SYNCN RTRV-ALM-SYNCN REPT EVT <MOD2ALM> RTRV-COND-<MOD2ALM> REPT EVT EQPT RTRV-COND-ALL REPT EVT SYNCN RTRV-COND-BITS RTRV-ALM-<MOD2ALM> RTRV-COND-EQPT RTRV-ALM-ALL RTRV-COND-SYNCN
Output Format	SID DATE TIME ** ATAG REPT ALM <MOD2ALM> "<ds1Aid>:<ntfcncde>,<condition>,<srveff>,,,,:[<desc>],<eqptType>" ; where: •ds1aid is the AID ds1 •ntfcncde is the 2-letter notification code and is of type NOTIF_CODE •condition is of type CONDITION •srveff is the effect on service caused by the alarm condition; srveff is of type SERV_EFF. •desc is a String •eqptType is of type EQPT_TYPE
Example	Output TID-000 98-06-20 14-30-00 ** 001 REPT ALM DS1 "DS1-14-3-5:MJ,LPBKFACILITY,SA,,,,:\"LOOP BACK ACTIVE\", DS3XM-6" ;

11.11.45 REPT ALM BITS: Report Alarm Building Integrated Timing Supply

Reports an alarm condition on a BITS facility.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-BITS REPT ALM ENV RTRV-ALM-ENV REPT ALM EQPT RTRV-ALM-EQPT REPT ALM SYNCN RTRV-ALM-SYNCN REPT EVT <MOD2ALM> RTRV-COND-<MOD2ALM> REPT EVT EQPT RTRV-COND-ALL REPT EVT SYNCN RTRV-COND-BITS RTRV-ALM-<MOD2ALM> RTRV-COND-EQPT RTRV-ALM-ALL RTRV-COND-SYNCN
Output Format	SID DATE TIME ** ATAG REPT ALM BITS "<bits_aid>:<ntfcncde>,<condition>,<srveff>,,,,:[<desc>]" ; where: •bits_aid is the AID bits •ntfcncde is the 2-letter notification code and is of type NOTIF_CODE •condition is a type of alarm condition and is of type CONDITION •srveff is the effect on service caused by the alarm condition; srveff is of type SERV_EFF •desc is a String
Example	Output TID-000 98-06-20 14-30-00 ** 001 REPT ALM BITS "BITS-1:MJ,SYNC,SA,,,,:\"LOSS OF TIMING\"," ;

11.11.46 REPT ALM ENV: Report Alarm Environment

Reports a customer-defined condition on an environmental alarm input.


Section	Description
Category	Environment
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-BITS REPT ALM BITS RTRV-ALM-EQPT REPT ALM EQPT RTRV-ALM-SYNCN REPT ALM SYNCN RTRV-COND-<MOD2ALM> REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN RTRV-ALM-ALL
Output Format	SID DATE TIME ** ATAG REPT ALM ENV "<env_aid>:<ntfcnnde>,<almtype>,,,<desc>" ; where: •env_aid is AID env •ntfcncde is of type NOTIF_CODE •almtype is of type ENV_ALM •desc is a String
Example	Output TID-000 98-06-20 14-30-00 ** 001 REPT ALM ENV "ENV-IN-1:MJ,OPENDR,,,\"OPEN DOOR\"" ;
Errors	This message generates all the default errors

11.11.47 REPT ALM EQPT: Report Alarm Equipment

Reports an alarm condition against an equipment unit or slot.


Section	Description
Category	Equipment
Security	Read Only
Related Messages	DLT-EQPT RTRV-ALM-<MOD2ALM> DLT-FFP-EQPT RTRV-ALM-ALL ED-FFP-EQPT RTRV-ALM-BITS ENT-EQPT RTRV-ALM-ENV ENT-FFP-EQPT RTRV-ALM-EQPT OPR-PROTNSW-EQPT RTRV-ALM-SYNCN REPT ALM <MOD2ALM> RTRV-COND-<MOD2ALM> REPT ALM BITS RTRV-COND-ALL REPT ALM ENV RTRV-COND-BITS REPT ALM SYNCN RTRV-COND-EQPT REPT EVT <MOD2ALM> RTRV-COND-SYNCN REPT EVT EQPT RTRV-EQPT REPT EVT SYNCN RTRV-FFP-EQPT RLS-PROTNSW-EQPT SW-DX-EQPT
Output Format	SID DATE TIME ** ATAG REPT ALM EQPT "<eqpt>:<ntfcncde>,<condition>,<srveff>,,,,,<desc>,<eqptType>" ; where: •eqpt is the equipment aid SLOT-{1-17} and is the AID eqpt •ntfcncde is the 2-letter notification code and is of type NOTIF_CODE •condition is the type of alarm condition and is of type CONDITION •srveff is the effect on service caused by the alarm condition and is of type SERV_EFF •desc is a String •eqptType is of type EQPT_TYPE
Example	Output TID-000 98-06-20 14-30-00 ** 001 REPT ALM EQPT "SLOT-7:MN,CONTR,NSA,,,,:\"CONTROLLER FAILURE\",TCC" ;

11.11.48 REPT ALM SYNCN: Report Alarm Synchronization

Reports an alarm condition against a synchronization reference.


Section	Description
Category	Synchronization
Security	Read Only
Related Messages	ED-SYNCN RTRV-ALM-BITS REPT ALM <MOD2ALM> RTRV-ALM-ENV REPT ALM BITS RTRV-ALM-EQPT REPT ALM ENV RTRV-ALM-SYNCN REPT ALM EQPT RTRV-COND-<MOD2ALM> REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN RTRV-ALM-ALL RTRV-SYNCN
Output Format	SID DATE TIME ** ATAG REPT ALM SYNCN "<sync_aid>:<ntfcncde>,<condition>,<srveff>,,,,:<desc>" ; where: •sync_aid is the identifier of Synchronization Reference with alarm condition; sync_aid is the AID sync_ref •ntfcncde is the 2-letter notification code and is of type NOTIF_CODE •condition is the type of alarm condition and is of type CONDITION •srveff is the effect on service caused by the alarm condition and is of type SERV_EFF •desc is a String
Example	Output TID-000 98-06-20 14-30-00 ** 001 REPT ALM SYNCN "SYNC-NE:MJ,MAN,SA,,,,:\"MANUAL SWITCH\"," ;

11.11.49 REPT EVT <MOD2ALM>: Report Event (DS1, E100, E1000, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

Reports the occurrence of a non-alarmed event.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-BITS REPT ALM BITS RTRV-ALM-ENV REPT ALM ENV RTRV-ALM-EQPT REPT ALM EQPT RTRV-ALM-SYNCN REPT ALM SYNCN RTRV-COND-<MOD2ALM> REPT EVT EQPT RTRV-COND-ALL REPT EVT SYNCN RTRV-COND-BITS RTRV-ALM-<MOD2ALM> RTRV-COND-EQPT RTRV-ALM-ALL RTRV-COND-SYNCN
Output Format	SID DATE TIME A ATAG REPT EVT <MOD2ALM> "<fac_aid>:<condition>,[<condeff>],,,[<location>],,[<monval>], [<th_val>],[<tmpr>]:<desc>,<eqptType>" ; where: •fac_aid is the identifier of the OC-N facility with the condition and is the AID facility •condition is of type CONDITION •condeff is the effect of the condition on the NE; condeff is of type COND_EFF and is optional •location is of type LOCATION and is optional •monval is the monitored value and is optional •th_val is the threshold value; th_val is an Integer and is optional •tmpr is the time period; tmpr is of type TMPR and is optional • desc is a String •eqptType is of type EQPT_TYPE
Example	Output TID-000 98-06-20 14-30-00 A 001 REPT EVT T3 "FAC-4-1:WKSWPR,TC,,,FEND,,12,13,15MIN:\"WORKING SWITCH TO PROTECTION\",DS3-12" ;

11.11.50 REPT EVT EQPT: Report Event Equipment

Reports the occurrence of a non-alarmed event against an equipment unit or slot.


Section	Description
Category	Equipment
Security	Read Only
Related Messages	DLT-EQPT RTRV-ALM-<MOD2ALM> DLT-FFP-EQPT RTRV-ALM-ALL ED-FFP-EQPT RTRV-ALM-BITS ENT-EQPT RTRV-ALM-ENV ENT-FFP-EQPT RTRV-ALM-EQPT OPR-PROTNSW-EQPT RTRV-ALM-SYNCN REPT ALM <MOD2ALM> RTRV-COND-<MOD2ALM> REPT ALM BITS RTRV-COND-ALL REPT ALM ENV RTRV-COND-BITS REPT ALM EQPT RTRV-COND-EQPT REPT ALM SYNCN RTRV-COND-SYNCN REPT EVT <MOD2ALM> RTRV-EQPT REPT EVT SYNCN RTRV-FFP-EQPT RLS-PROTNSW-EQPT SW-DX-EQPT
Output Format	SID DATE TIME A ATAG REPT EVT EQPT "<eqpt>:<condition>,<condeff>,<eqptType>,,,,,:[<desc>]" ; where: •eqpt is the slot number of the equipment and is the AID eqpt •condition is the type of event and is of type CONDITION •condeff is the effect of the condition on the NE; condeff is of type COND_EFF •eqptType is the equipment type and is of type EQPT_TYPE •desc is a String
Example	Output TID-000 98-06-20 14-30-00 A 001 REPT EVT EQPT "SLOT-7:,PLUGIN,TC,TCC,,,,,:\"EQUIPMENT PLUG-IN\"," ;

11.11.51 REPT EVT SYNCN: Report Event Synchronization

Reports the occurrence of a non-alarmed event against a synchronization entity.


Section	Description
Category	Synchronization
Security	Read Only
Related Messages	ED-SYNCN RTRV-ALM-BITS REPT ALM <MOD2ALM> RTRV-ALM-ENV REPT ALM BITS RTRV-ALM-EQPT REPT ALM ENV RTRV-ALM-SYNCN REPT ALM EQPT RTRV-COND-<MOD2ALM> REPT ALM SYNCN RTRV-COND-ALL REPT EVT <MOD2ALM> RTRV-COND-BITS REPT EVT EQPT RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN RTRV-ALM-ALL RTRV-SYNCN
Output Format	SID DATE TIME A ATAG REPT EVT SYNCN "<sync_aid>:<condition>,<condeff>,,,,,,:[<desc>]" ; where: •sync_aid is the identifier of the synchronization entity with the condition; sync_aid is the AID sync_ref •condition is of type CONDITION •condeff is of type COND_EFF •desc is a String
Example	Output TID-000 98-06-20 14-30-00 A 001 REPT EVT SYNCN "SYNC-NE:SWTOINT,SC,,,,,,:\"SWITCH TO INTERNAL CLOCK\"," ;

11.11.52 RLS-LPBK-<OCN_TYPE>: Release Loopback (OC3, OC12, OC48)

This command instructs the NE to release a loopback on the specified OC-N facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	OPR-LPBK-<OCN_TYPE> OPR-LPBK-DS1 OPR-LPBK-EC1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-DS1 RLS-LPBK-EC1 RLS-LPBK-T1 RLS-LPBK-T3
Input Format	RLS-LPBK-<OCN_TYPE>:[TID]:<fac_aid>:[CTAG]::,,,[<lpbktype>]; where: •fac_aid is the AID facility •lpbktype is the type of loopback to be released and is of type LPBK_TYPE
Example	Input RLS-LPBK-OC3:PTREYES:FAC-12-1:208::,,,FACILITY;
Errors	This message generates all the default errors

11.11.53 RLS-LPBK-DS1: Release Loopback Digital Signal Level 1

This command releases a DS-1 signal loopback for the DS3XM-6 card.

Note The TERMINAL loopback is not supported.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	OPR-LPBK-<OCN_TYPE> OPR-LPBK-DS1 OPR-LPBK-EC1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-EC1 RLS-LPBK-T1 RLS-LPBK-T3
Input Format	RLS-LPBK-DS1:[TID]:<ds1Aid>:[CTAG]::,,,[<lpbkType>]; where: •ds1Aid is the AID ds1 •lpbkType is of type LPBK_TYPE
Example	Input RLS-LPBK-DS1:PTREYES:DS1-4-2-13:203::,,,FACILITY;
Errors	This message generates all the default errors

11.11.54 RLS-LPBK-EC1: Release Loopback Electrical Carrier Level 1

This command releases loopback for an EC-1 facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	OPR-LPBK-<OCN_TYPE> OPR-LPBK-DS1 OPR-LPBK-EC1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-DS1 RLS-LPBK-T1 RLS-LPBK-T3
Input Format	RLS-LPBK-EC1:[TID]:<facility>:[CTAG]::,,,<lpbkType>; where: •facility is the AID facility •lpbkType is of type LPBK_TYPE
Example	Input RLS-LPBK-EC1:PTREYES:FAC-3-12:203::,,,FACILITY;
Errors	This message generates all the default errors

11.11.55 RLS-LPBK-T1: Release Loopback T1 Facility

This command instructs the NE to release the loopback for the T1 facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	ED-T1 ED-T3 OPR-LPBK-<OCN_TYPE> OPR-LPBK-DS1 OPR-LPBK-EC1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-DS1 RLS-LPBK-EC1 RLS-LPBK-T3 RTRV-T1 RTRV-T3
Input Format	RLS-LPBK-T1:[TID]:<fac>:[CTAG]::,,,[<lpbk_type>]; where: •fac releases the loopback for a T1 facility. fac is the AID facility. •lpbk_type is of type LPBK_TYPE.
Example	Input RLS-LPBK-T1:PTREYES:FAC-1-12:203::,,,FACILITY;
Errors	This message generates all of the Default Errors.

11.11.56 RLS-LPBK-T3: Release Loopback T3 Facility

This command instructs the NE to release a loopback on the specified T3 facility.


Section	Description
Category	Testing
Security	Read/Write
Related Messages	ED-T1 ED-T3 OPR-LPBK-<OCN_TYPE> OPR-LPBK-DS1 OPR-LPBK-EC1 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-<OCN_TYPE> RLS-LPBK-DS1 RLS-LPBK-EC1 RLS-LPBK-T1 RTRV-T1 RTRV-T3
Input Format	RLS-LPBK-T3:[TID]:<fac_aid>:[CTAG]::,,,[<lpbk_type>]; where: •fac_aid is the AID facility •lpbktype is the type of loopback to be released; lpbktype is of type LPBK_TYPE.
Example	Input RLS-LPBK-T3:SCHELLVILLE:FAC-6-11:207::,,,TERMINAL;
Errors	This message generates all the default errors

11.11.57 RLS-PROTNSW-<OCN_TYPE>: Release Protection Switch (OC3, OC12, OC48)

Instructs the NE to release a line protection switch request between a working line and a protection line.


Section	Description
Category	Switch
Security	Read/Write
Related Messages	N/A
Input Format	RLS-PROTNSW-<OCN_TYPE>:[TID]:<fac_aid>:[CTAG]; where: •fac_aid is the AID facility
Example	Input RLS-PROTNSW-OC48:CHICKALUMA:FAC-6-1:209;
Errors	This message generates all the default errors

11.11.58 RLS-PROTNSW-EQPT: Release Protection Switch Equipment

This command instructs the NE to release a protection switch on an equipment unit.


Section	Description
Category	Equipment
Security	Read/Write
Related Messages	DLT-EQPT REPT EVT EQPT DLT-FFP-EQPT RTRV-ALM-EQPT ED-FFP-EQPT RTRV-COND-EQPT ENT-EQPT RTRV-EQPT ENT-FFP-EQPT RTRV-FFP-EQPT OPR-PROTNSW-EQPT SW-DX-EQPT REPT ALM EQPT
Input Format	RLS-PROTNSW-EQPT:[TID]:<eqpt_aid>:[CTAG]; where: •eqpt_aid is the AID eqpt
Example	Input RLS-PROTNSW-EQPT:LASLOMAS:SLOT-3:401;
Errors	This message generates all the default errors

11.11.59 RMV-<MOD2>: Remove (DS1, EC1,OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command removes a facility from an in service state to out of service.

Note RMV-DS1/STS1/STS3C/STS12C/STS48C/VT1 are not supported in Release 2.2.1.


Section	Description
Category	Facility
Security	N/A
Related Messages	N/A
Input Format	RMV-<MOD2>:[TID]:<facility>:[CTAG]; where: •facility is the AID facility
Example	Input RMV-EC1:CISCO:FAC-1-1:1234;
Errors	This message generates all the default errors

11.11.60 RST-<MOD2>: Restore (DS1, EC1,OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command provisions a facility in service.


Section	Description
Category	Facility
Security	N/A
Related Messages	N/A
Input Format	RST-<MOD2>:[TID]:<facility>:[CTAG]; where: •facility is the AID facility
Example	Input RST-EC1:CISCO:FAC-1-1:1234;
Errors	This message generates all the default errors

11.11.61 RTRV-<OCN_TYPE>: Retrieve (OC3, OC12, OC48)

This command retrieves the parameters of an OC-N facility.


Section	Description
Category	Other
Security	Read Only
Related Messages	N/A
Input Format	RTRV-<OCN_TYPE>:[TID]:<fac_aid>:[CTAG]::::; where: •fac_aid is the AID facility and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<fac_aid>:[SDCC=<sdcc>],[TMERGF=<tmgref>],[SPNWTR=<spnwtr>], [PJMON=<pjmon>],[SFBER=<sfber>],[SDBER=<sdber>], [MODE=<mode>],[WVLEN=<wvlen>]:<pst>,,<role>,<status>" ; where: •fac_aid is the AID facility •sdcc is of type SDCC_MODE and is optional •tmgref is of type TMG_REF and is optional •spnwtr is of type REVERTIVE_TIME and is optional •pjmon is an Integer and is optional •sfber is of type SF_BER and is optional •sdber is of type SD_BER and is optional •mode is of type OPTICAL-MODE. mode is optional •wvlen is the optical signal wavelength in nanometers; it is a Float and is optional •pst is of type PST •role is of type SIDE •status is of type STATUS
Example	Input RTRV-OC3:CISCO:FAC-15-2:123::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-15-2:SDCC=N, TMGREF=N, SPNWTR=8.5, PJMON=0, SFBER=1E-4, SDBER=1E-7, MODE=SONET, WVLEN=1310.00:OOS,, WORK,STBY" ;
Errors	This message generates all the default errors

11.11.62 RTRV-<STS_PATH>: Retrieve (STS1, STS3C, STS12C)

This command retrieves the attributes associated with an STS path.


Section	Description
Category	Other
Security	Read Only
Related Messages	N/A
Input Format	RTRV-<STS_PATH>:[TID]:<sts_aid>:[CTAG]::::; where: •sts_aid is the AID sts and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<sts_aid>:RATE=<stsrate>,[SFBER=<sfber>],[SDBER=<sdber>]" ; where: •sts_aid is the AID sts •stsrate is the STS Rate and is of type STS_PATH •sfber is of type SF_BER and is optional •sdber is of type SD_BER and is optional
Example	Input RTRV-STS1:FERNDALE:STS-2-4:238::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "STS-2-4:RATE=STS1,SFBER=1E-3,SDBER=1E-5" ;
Errors	This message generates all the default errors

11.11.63 RTRV-ALM-<MOD2ALM>:Retrieve Alarm (DS1, E100, E1000, EC1, OC12, OC3, OC48, STS1, STS12C, STS3C, STS48C, T1, T3, VT1)

Instructs the network to retrieve and send the current status of its alarm conditions. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-BITS REPT ALM BITS RTRV-ALM-ENV REPT ALM ENV RTRV-ALM-EQPT REPT ALM EQPT RTRV-ALM-SYNCN REPT ALM SYNCN RTRV-COND-<MOD2ALM> REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-ALL RTRV-COND-SYNCN
Input Format	RTRV-ALM-<MOD2ALM>:[TID]:<aid>:[CTAG]::[<ntfcncde>],[<condition>], [<serv_eff>],,,; where: •aid is the AID facility and must not be null •ntfcnde is the 2-letter notification code and is of type NOTIF_CODE; a null value is equivalent to "ALL" •condition is a type of alarm condition and is of type CONDITION; condition is listable and a null value is equivalent to "ALL" •serveff of type SERV_EFF and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<aid>,<type>:<ntfcnde>,<condition>,<srveff>,,,,:<desc>" ; where: •aid is the AID facility •type specifies the type of OC-N facility associated with the facility AID; type is of type MOD2ALM •ntfcnde is the 2-letter notification code and is of type NOTIF_CODE •condition is a type of alarm condition and is of type CONDITION •srveff is the type of effect on service caused by the alarm condition and is of type SERV_EFF •desc is a String
Example	Input RTRV-ALM-OC12:ELDRIDGE:FAC-6-1:255::MN,SD,SA,,,; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-6-1,OC12:MJ,SD,SA,,,,:\"BER AT SIGNAL DEGRADE LEVEL\"," ;
Errors	This message generates all the default errors

11.11.64 RTRV-ALM-ALL: Retrieve Alarm All

This command instructs the NE to retrieve and send the current status of all active alarm conditions. The alarm condition or severity retrieved is specified using the input parameters as a filter.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-BITS REPT ALM BITS RTRV-ALM-ENV REPT ALM ENV RTRV-ALM-EQPT REPT ALM EQPT RTRV-ALM-SYNCN REPT ALM SYNCN RTRV-COND-<MOD2ALM> REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN
Input Format	RTRV-ALM-ALL:[TID]::[CTAG]::,,,,,;
Output Format	SID DATE TIME M CTAG COMPLD "<aid>,<aid_type>:<notifCode>,<condition1>,<servEff>,,,,,:<dnField>" ; where: •aid is the aid where the alarm took place and d is the AID ALL •aid_type is of type MOD2 •notifCode is of type NOTIF_CODE •condition1 is of type CONDITION •servEff is a service-affecting alarm and is of type SERV_EFF •dsField is a String
Example	Input RTRV-ALM-ALL:COTATI::229::,,,,,; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SLOT-2,EQPT:MN,PWRRESTART,NSA,,,,,:\"POWERFAIL RESTART\"," ;
Errors	This message generates all the default errors

11.11.65 RTRV-ALM-BITS: Retrieve Alarm Building Integrated Timing Supply

This command instructs the NE to retrieve and send the current status of its alarm conditions associated with the BITS facility. The alarm condition or severity retrieved is specified using the input parameters as a filter.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-ALL REPT ALM BITS RTRV-ALM-ENV REPT ALM ENV RTRV-ALM-EQPT REPT ALM EQPT RTRV-ALM-SYNCN REPT ALM SYNCN RTRV-COND-<MOD2ALM> REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN
Input Format	RTRV-ALM-BITS:[TID]:<bits_aid>:[CTAG]::[<ntfcncde>],[<condition>], [<serv_eff>]; where: •bits_aid is the AID bits and must not be null. •ntfcncde is a 2-letter notification code and is of type NOTIF_CODE; a null value is equivalent to "ALL" •condition is a type of alarm condition and is of type CONDITION; condition is listable and a null value is equivalent to "ALL" •serv_eff is a type of effect on service caused by the alarm condition and is of type SERV_EFF; a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<bits_aid>:<ntfcncde>,<condition>,<srveff>,,,,:<desc>" ; where: •bits_aid is the AID bits •ntfcncde is a 2-letter notification code and is of type NOTIF_CODE •condition is a type of alarm condition and is of type CONDITION •srveff is a type of effect on service caused by the alarm condition and is of type SERV_EFF •desc is a String
Example	Input RTRV-ALM-BITS:ELVERANO:BITS-1:288::CR,LOS,SA; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "BITS-1:CR,LOS,SA,,,,:\"LOSS OF SIGNAL\"," ;
Errors	This message generates all the default errors

11.11.66 RTRV-ALM-ENV: Retrieve Alarm Environment

This command instructs the NE to retrieve outstanding environmental alarms.


Section	Description
Category	Environment
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-ALL REPT ALM BITS RTRV-ALM-BITS REPT ALM ENV RTRV-ALM-EQPT REPT ALM EQPT RTRV-ALM-SYNCN REPT ALM SYNCN RTRV-COND-<MOD2ALM> REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN
Input Format	RTRV-ALM-ENV:[TID]:[<env>]:[CTAG]::[<notifCode>],[<envAlm>]; where: •env is the AID env and is listable; a null value is equivalent to "ALL" •notifCode is of type NOTIF_CODE and a null value is equivalent to "ALL" •envAlm is of type ENV_ALM and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<env>:<notifCode>,<envAlm>,,,[<desc>]" ; where: •env is the AID env •notifCode is of type NOTIF_CODE •envAlm is of type ENV_ALM •desc is a String
Example	Input RTRV-ALM-ENV:CISCO-1:ENV-IN-1:123::MJ,OPENDR; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "ENV-IN-1:MJ,OPENDR,,,\"OPEN DOOR\"" ;
Errors	This message generates all the default errors

11.11.67 RTRV-ALM-EQPT: Retrieve Alarm Equipment

This command instructs the NE to retrieve and send the current status of its equipment-unit alarm conditions. The alarm condition or severity retrieved is specified using the input parameters as a filter.


Section	Description
Category	Equipment
Security	Read Only
Related Messages	DLT-EQPT RLS-PROTNSW-EQPT DLT-FFP-EQPT RTRV-ALM-<MOD2ALM> ED-FFP-EQPT RTRV-ALM-ALL ENT-EQPT RTRV-ALM-BITS ENT-FFP-EQPT RTRV-ALM-ENV OPR-PROTNSW-EQPT RTRV-ALM-SYNCN REPT ALM <MOD2ALM> RTRV-COND-<MOD2ALM> REPT ALM BITS RTRV-COND-ALL REPT ALM ENV RTRV-COND-BITS REPT ALM EQPT RTRV-COND-EQPT REPT ALM SYNCN RTRV-COND-SYNCN REPT EVT <MOD2ALM> RTRV-EQPT REPT EVT EQPT RTRV-FFP-EQPT REPT EVT SYNCN SW-DX-EQPT
Input Format	RTRV-ALM-EQPT:[TID]:<eqpt_aid>:[CTAG]::[<ntfcncde>],[<condition>], [<serv_eff>],,,; where: •eqpt_aid is the AID eqpt and must not be null •ntfcncde is a 2-letter notification code and is of type NOTIF_CODE; a null value is equivalent to "ALL" •condition is a type of alarm condition and is of type CONDITION; condition is listable and a null value is equivalent to "ALL" •serv_eff is of type SERV_EFF and is null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<eqpt>,<eqpt_type>:<ntfcncde>,<condition>,<srveff>,,,,:<desc>" ; where: •eqpt is the AID eqpt •eqpt_type specifies the type of card associated with the slot AID for equipment units; eqpt_type is of type EQPT_TYPE •ntfcncde is a 2-letter notification code and is of type NOTIF_CODE •condition is a type of alarm condition and is of type CONDITION •srveff is a type of effect on service caused by the alarm condition; srveff is of type SERV_EFF •desc is a String
Example	Input RTRV-ALM-EQPT:TWOROCK:SLOT-7:227::MJ,HITEMP,NSA,,,; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SLOT-7,TCC:MJ,HITEMP,NSA,,,,:\"HIGH TEMPERATURE\"," ;
Errors	This message generates all the default errors

11.11.68 RTRV-ALM-SYNCN: Retrieve Alarm Synchronization

Instructs the NE to retrieve and send the current status of its alarm conditions associated with a synchronization facility. The alarm condition or severity to be retrieved can be specified by using the input parameters as a filter.


Section	Description
Category	Synchronization
Security	Read Only
Related Messages	ED-SYNCN RTRV-ALM-ALL OPR-SYNCNSW RTRV-ALM-BITS REPT ALM <MOD2ALM> RTRV-ALM-ENV REPT ALM BITS RTRV-ALM-EQPT REPT ALM ENV RTRV-COND-<MOD2ALM> REPT ALM EQPT RTRV-COND-ALL REPT ALM SYNCN RTRV-COND-BITS REPT EVT <MOD2ALM> RTRV-COND-EQPT REPT EVT EQPT RTRV-COND-SYNCN REPT EVT SYNCN RTRV-SYNCN RTRV-ALM-<MOD2ALM>
Input Format	RTRV-ALM-SYNCN:[TID]:[<sync_aid>]:[CTAG]::[<ntfcncde>],[<condition>], [<serv_eff>]; where: •sync_aid is the AID sync_ref and is listable; a null value is equivalent to "ALL" •ntfcncde is a 2-letter notification code and is of type NOTIF_CODE; a null value is equivalent to "ALL" •condition is a type of alarm condition and is of type CONDITION; condition is listable and a null value is equivalent to "ALL" •serv_eff is a type of effect on service caused by the alarm condition; serv_eff is of type SERV_EFF and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<sync_aid>:<ntfcncde>,<condition>,<srveff>,,,,:<desc>" ; where: •sync_aid identifies the facility queried and is the AID sync_ref •ntfcncde is a 2-letter notification code and is of type NOTIF_CODE •condition is a type of alarm condition and is of type CONDITION •srveff is a type of effect on service caused by the alarm condition; serveff is of type SERV_EFF •desc is a String
Example	Input RTRV-ALM-SYNCN:FULTON:SYNC-NE:226::CR,FAILTOSW,SA; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SYNC-NE:CR,FAILTOSW,SA,,,,:\"FAILURE TO SWITCH TO PROTECTION\"," ;
Errors	This message generates all the default errors

11.11.69 RTRV-BITS: Retrieve Building Integrated Timing Supply

This command retrieves the BITS configuration command.


Section	Description
Category	Other
Security	Read Only
Related Messages	N/A
Input Format	RTRV-BITS:[TID]:<bits_aid>:[CTAG]::::; where: •bits_aid is the AID bits and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<bits_aid>:LNCDE=<line_code>,FMT=<frame_format>:<pst>" ; where: •bits_aid is the AID bits •line_code is of type LINE_CODE •frame_format is of type FRAME_FORMAT •pst is of type PST
Example	Input RTRV-BITS:SONOMA:BITS-1:782::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "BITS-1:LNCDE=AMI,FMT=ESF:IS" ;
Errors	This message generates all the default errors

11.11.70 RTRV-COND-<MOD2ALM>: Retrieve Condition (DS1, E100, E1000, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command instructs the NE to retrieve the current standing condition and/or state associated with an entity.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-ALL REPT ALM BITS RTRV-ALM-BITS REPT ALM ENV RTRV-ALM-ENV REPT ALM EQPT RTRV-ALM-EQPT REPT ALM SYNCN RTRV-ALM-SYNCN REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN
Input Format	RTRV-COND-<MOD2ALM>:[TID]:[<facility>]:[CTAG]::[<condition>],,,; where: •facility is the facility aid and is the AID facility; a null value is equivalent to "ALL" •condition is the requested condition, if not set=> we want all the conditions for the specified facility; condition is of type CONDITION and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<facility>,<eqptType>:[<notifcode>],<condition>,[<servEff>],,,,,, [<desc>]" ; where: •facility is the facility aid and is the AID facility •eqptType is of type EQPT_TYPE •notifCode is the notification code; notifCode is of type NOTIF_CODE and is optional •condition is the condition itself and is of type CONDITION •servEff is of type SERV_EFF and is optional •desc is the condition description; desc is a String and is optional
Example	Input RTRV-COND-T3:TID:FAC-2-1:229::LOS,,,; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-2-1,DS3-12:CR,LOS,SA,,,,,,\"LOS OF SIGNAL\"" ;
Errors	This message generates all the default errors

11.11.71 RTRV-COND-ALL: Retrieve Condition All

This command instructs the NE to retrieve the current standing condition for all entities.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-ALL REPT ALM BITS RTRV-ALM-BITS REPT ALM ENV RTRV-ALM-ENV REPT ALM EQPT RTRV-ALM-EQPT REPT ALM SYNCN RTRV-ALM-SYNCN REPT EVT <MOD2ALM> RTRV-COND-<MOD2ALM> REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN
Input Format	RTRV-COND-ALL:[TID]::[CTAG]::[<condition>],::; where: •condition is of type CONDITION and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<facility>,[<aid_type>]:[<notifCode>],<condition>,[<servEff>],,,,,, [<desc>]" ; where: •facility is the AID facility •aid_type is of type MOD2B and is optional •notifCode is of type NOTIF_CODE and is optional •condition is of type CONDITION •servEff is of type SERV_EFF and is optional •desc is a String and is optional
Example	Input RTRV-COND-ALL::TID::229::LOS,,,: Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-2-1,OC3:CR,LOS,SA,,,,,,\"LOS OF SIGNAL\"" ;
Errors	This message generates all the default errors

11.11.72 RTRV-COND-BITS: Retrieve Condition Building Integrated Timing Supply

This command instructs the NE to retrieve the standing conditions on BITS.


Section	Description
Category	Fault
Security	Read Only
Related Messages	REPT ALM <MOD2ALM> RTRV-ALM-ALL REPT ALM BITS RTRV-ALM-BITS REPT ALM ENV RTRV-ALM-ENV REPT ALM EQPT RTRV-ALM-EQPT REPT ALM SYNCN RTRV-ALM-SYNCN REPT EVT <MOD2ALM> RTRV-COND-<MOD2ALM> REPT EVT EQPT RTRV-COND-ALL REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2ALM> RTRV-COND-SYNCN
Input Format	RTRV-COND-BITS:[TID]:<facility>:[CTAG]::[<condition>],,,; where: •facility is the AID bits and must not be null •condition is of type CONDITION and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<facility>,<eqptType>:[<notifCode>],<condition>,[<servEff>],,,,,, [<desc>]" ; where: •facility is the AID bits •eqptType is of type EQPT_TYPE •notifCode is of type NOTIF_CODE and is optional •condition is of type CONDITION •servEff is of type SERV_EFF and is optional •desc is a String and is optional
Example	Input RTRV-COND-BITS:TID:BITS-1:229::LOS,,,: Output TID-000 98-06-20 14-30-00 M 001 COMPLD "BITS-1,TCC:CR,LOS,SA,,,,,,\"LOS OF SIGNAL\"" ;
Errors	This message generates all the default errors

11.11.73 RTRV-COND-EQPT: Retrieve Condition Equipment

This command instructs the NE to retrieve current equipment conditions.


Section	Description
Category	Equipment
Security	Read Only
Related Messages	DLT-EQPT RLS-PROTNSW-EQPT DLT-FFP-EQPT RTRV-ALM-<MOD2ALM> ED-FFP-EQPT RTRV-ALM-ALL ENT-EQPT RTRV-ALM-BITS ENT-FFP-EQPT RTRV-ALM-ENV OPR-PROTNSW-EQPT RTRV-ALM-EQPT REPT ALM <MOD2ALM> RTRV-ALM-SYNCN REPT ALM BITS RTRV-COND-<MOD2ALM> REPT ALM ENV RTRV-COND-ALL REPT ALM EQPT RTRV-COND-BITS REPT ALM SYNCN RTRV-COND-SYNCN REPT EVT <MOD2ALM> RTRV-EQPT REPT EVT EQPT RTRV-FFP-EQPT REPT EVT SYNCN SW-DX-EQPT
Input Format	RTRV-COND-EQPT:[TID]:<facility>:[CTAG]::[<condition>],,,; where: •facility is the AID and must not be null. •condition is of type CONDITION and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<facility>,<eqptType>:[<notifCode>],<condition>,[<servEff>],,,,,,[<desc>]" ; where: •facility is the AID facility •eqptType is of type EQPT_TYPE •notifCode is of type NOTIF_CODE and is optional •condition is of type CONDITION •servEff is of type SERV_EFF and is optional •desc is a String and is optional
Example	Input RTRV-COND-EQPT:TID:SLOT-1:229::LOS,,,: Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SLOT-1,DS3-12:CR,LOS,SA,,,,,,,\"LOS OF SIGNAL\"" ;
Errors	This message generates all the default errors

11.11.74 RTRV-COND-SYNCN: Retrieve Condition Synchronization

This command retrieves the synchronization condition.


Section	Description
Category	Synchronization
Security	Read Only
Related Messages	ED-SYNCN RTRV-ALM-ALL REPT ALM <MOD2ALM> RTRV-ALM-BITS REPT ALM BITS RTRV-ALM-ENV REPT ALM ENV RTRV-ALM-EQPT REPT ALM EQPT RTRV-ALM-SYNCN REPT ALM SYNCN RTRV-COND-<MOD2ALM> REPT EVT <MOD2ALM> RTRV-COND-ALL REPT EVT EQPT RTRV-COND-BITS REPT EVT SYNCN RTRV-COND-EQPT RTRV-ALM-<MOD2> RTRV-SYNCN
Input Format	RTRV-COND-SYNCN:[TID]:<facility>:[CTAG]::[<condition>],,,; where: •facility is the AID sync_ref and must not be null •condition is of type CONDITION and a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<facility>,[<eqptType>]:[<notifCode>],<condition>,[<servEff>],,,,,, [<desc>]" ; where: •facility is the AID sync_ref •eqptType is of type EQPT_TYPE and is optional •notifCode is of type NOTIF_CODE and is optional •condition is of type CONDITION •servEff is of type SERV_EFF and is optional •desc is a String and is optional
Example	Input RTRV-COND-SYNCN:TID:SYNC-NE:229::LOS,,,: Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SYNC-NE,TCC:MJ,FRNGSYNC,SA,,,,,,\"FREE RUNNING SYNCHRONIZAION MODE\"" ;
Errors	This message generates all the default errors

11.11.75 RTRV-CRS-<STS_PATH>: Retrieve Cross Connect (STS1, STS3C STS12C)

This command retrieves any connections associated with the Access Identifiers entered. FROM and TO information is returned along with the type of connection.


Section	Description
Category	Cross Connect
Security	Read Only
Related Messages	DLT-CRS-<STS_PATH> DLT-CRS-VT1 ED-CRS-<STS_PATH> ED-CRS-VT1 ENT-CRS-<STS_PATH> ENT-CRS-VT1 RTRV-CRS-VT1
Input Format	RTRV-CRS-<STS_PATH>:[TID]:<sts_ep>:[CTAG]::,,,; where: •sts_ep is the AID sts and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<crs_ep>,<crs_ep1>:<cct>" ; where: •crs_ep is the AID sts •crs_ep1 is the AID sts •cct is the cross connect type and is of type CCT
Example	Input RTRV-CRS-STS3C:KENWOOD:STS-6-1:223::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "STS-6-1,STS-12-4:2WAY" ;
Errors	This message generates all the default errors

11.11.76 RTRV-CRS-VT1: Retrieve Cross Connect Virtual Tributary

This command retrieves the VT cross-connection information.


Section	Description
Category	Cross Connect
Security	Read Only
Related Messages	DLT-CRS-<STS_PATH> DLT-CRS-VT1 ED-CRS-<STS_PATH> ED-CRS-VT1 ENT-CRS-<STS_PATH> ENT-CRS-VT1 RTRV-CRS-<STS_PATH>
Input Format	RTRV-CRS-VT1:[TID]:<vt>:[CTAG]::::; where: •vt is the AID vt1_5 and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<from>,<to>:<cct>" ; where: •from is the first (FROM) VT in cross-connection and is the AID vt1_5 •to is the second (TO) VT in cross-connection and is the AID vt1_5 •cct is the cross connect type and is of type CCT
Example	Input RTRV-CRS-VT1:CISCO:VT1-2-3-1:1234::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "VT1-2-3-1,VT1-4-4-1:1WAY" ;
Errors	This message generates all the default errors

11.11.77 RTRV-EC1: Retrieve Electrical Carrier Level 1

This command retrieves the facility status of an EC-1 card.


Section	Description
Category	Other
Security	Read Only
Related Messages	N/A
Input Format	RTRV-EC1:[TID]:<fac>:[CTAG]::::; where: •fac is the facility aid and is the AID facility; fac must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<fac>:PJMON=<pjmon>,LBO=<lbo>:PST=<pst>" ; where: •fac is the facility aid and is the AID facility •pjmon is the SONET pointer monitor and is an Integer •lbo is line buildout and is of type E_LBO •pst is the primary service state and is of type PST
Example	Input RTRV-EC1:CISCO:FAC-1-1:1234::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-1-1:PJMON=0,LBO=0-225:PST=IS" ;
Errors	This message generates all the default errors

11.11.78 RTRV-EQPT: Retrieve Equipment

This command retrieves the data and state parameters associated with an equipment unit.


Section	Description
Category	Equipment
Security	Read Only
Related Messages	DLT-EQPT REPT EVT EQPT DLT-FFP-EQPT RLS-PROTNSW-EQPT ED-FFP-EQPT RTRV-ALM-EQPT ENT-EQPT RTRV-COND-EQPT ENT-FFP-EQPT RTRV-FFP-EQPT OPR-PROTNSW-EQPT SW-DX-EQPT REPT ALM EQPT
Input Format	RTRV-EQPT:[TID]:<eqpt_aid>:[CTAG]::::; where: •eqpt_aid is the AID eqpt and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<eqpt_aid>:[<eqpt_type>]:[WTR=<wtr>],[NAME=<name>]:<state>, <equip>,[<role>],[<status>]" ; where: •eqpt_aid is the AID eqpt •eqpt_type is the type of card in the slot; eqpt_type is of type EQPT_TYPE and is optional •wtr is an Integer and is optional •name is a String and is optional •state is of type PST •equip indicates if the equipment unit is physically present and is of type EQUIP. •role indicates if the card is a working unit or the protecting unit; role is of type SIDE and is optional •status is of type STATUS and is optional
Example	Input RTRV-EQPT:MIRABEL:SLOT-12:230::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SLOT-12:OC12:WTR=99,NAME=DESCRIPTION:IS,EQUIP,,ACT" ;
Errors	This message generates all the default errors

11.11.79 RTRV-FFP-<OCN_TYPE>: Retrieve Facilities Protection Group (OC3, OC12, OC48)

This command retrieves the optical facility protection information.


Section	Description
Category	Facility Protection
Security	Read Only
Related Messages	N/A
Input Format	RTRV-FFP-<OCN_TYPE>:[TID]:<facility>:[CTAG]; where: •facility is the AID facility and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<work>,<protect>:NAME=<name>,RVTT=<revertiveType>, RVTM=<revertiveTime>,BSWM=<bswMode>" ; where: •work is the AID facility •protect is the AID facility •name is the protection name and is a String •revertiveType is the revertive type and e is of type REVERTIVE_TYPE •revertiveTime is the revertive time and is of type REVERTIVE_TIME •bswMode specifies if it is a bidirectional switch mode and is of type ON_OFF
Example	Input RTRV-FFP-OC3:PETALUMA:FAC-3-1:1; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-3-1,FAC-4-1:NAME=PROT_NAME,RVTT=R,RVTM=1.0, BSWM=OFF" ;
Errors	This message generates all the default errors

11.11.80 RTRV-FFP-EQPT: Retrieve Facilities Protection Group Equipment

This command retrieves the equipment protection information.


Section	Description
Category	Equipment
Security	Read Only
Related Messages	DLT-EQPT REPT EVT EQPT DLT-FFP-EQPT RLS-PROTNSW-EQPT ED-FFP-EQPT RTRV-ALM-EQPT ENT-EQPT RTRV-COND-EQPT ENT-FFP-EQPT RTRV-EQPT OPR-PROTNSW-EQPT SW-DX-EQPT REPT ALM EQPT
Input Format	RTRV-FFP-EQPT:[TID]:<eqpt>:[CTAG]; where: •eqpt is the AID eqpt and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<work>,<protect>:PRT=<protectionGroup>,NAME=<name>, RVTT=<revertiveType>,RVTM=<revertiveTime>,BSWM=<bswMode>" ; where: •work is the working slot aid and is the AID eqpt •protect is the protection slot aid and is the AID eqpt •protectionGroup is the protection group and is of type PROTECTION_GROUP •name is the protection name and is a String •revertiveType is of type REVERTIVE_TYPE •revertiveTime is of type REVERTIVE_TIME
Example	Input RTRV-FFP-EQPT:PETALUMA:SLOT-16:1; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SLOT-16,SLOT-17:PRT=1-1,NAME=PROT_NAME,RVTT=R,RVTM=1.0" ;
Errors	This message generates all the default errors

11.11.81 RTRV-HDR: Retrieve Header

This command instructs the NE to return the header of a TL1 response message. Used by TL1 clients to determine if the link to the NE is still active and if the NE is responding to commands.


Section	Description
Category	System
Security	Read Only
Related Messages	ACT-USER ALW-MSG-ALL CANC-USER ED-DAT INH-MSG-ALL INIT-SYS
Input Format	RTRV-HDR:[TID]::[CTAG];
Example	Input RTRV-HDR:SONOMA::232;
Errors	This message generates all the default errors

11.11.82 RTRV-INV: Retrieve Inventory

This command queries the NE and returns a listing of the equipment inventory. For each unit in the system, it identifies the unit's hardware version and revision numbers, firmware version, and the unit's CLEI code.


Section	Description
Category	Other
Security	Read Only
Related Messages	N/A
Input Format	RTRV-INV:[TID]:<eqpt_aid>:[CTAG]::,,; where: eqpt_aid is the AID eqpt and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<eqpt_aid>,<eqptType>:[PN=<pn>],[HWVER=<hwver>], [FWVER=<fwver>],[SN=<sn>],[CLEI=<clei>]" ; where: •eqpt_aid is the AID eqpt • eqpt_type is of type EQPT_TYPE •pn is a String and is optional •hwver is a String and is optional •fwver is a String and is optional •sn is an integer and is optional •clei is a String and is optional
Example	Input RTRV-INV:OCCIDENTAL:SLOT-15:301::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SLOT-15,OC3-IR-4:PN=87-00002,HWVER=004K, FWVER=76-99-00009-004A,SN=013510,CLEI=NOCLEI" ;
Errors	This message generates all the default errors

11.11.83 RTRV-LOG: Retrieve Log

This command retrieves the alarm log of the NE.


Section	Description
Category	Log
Security	Read Only
Related Messages	N/A
Input Format	RTRV-LOG:[TID]::[CTAG];
Output Format	SID DATE TIME M CTAG COMPLD "<aid>,<seq>:CURRENT=<current>,[PREVIOUS=<previous>], <condition>,servEff>,[TIME=<time>],DATE=<date>:<desc>" ; where: •aid is the AID ALL •seq is an Integer •current is of type NOTIF_CODE •previous is of type COND_EFF and is optional •condition is of type CONDITION •servEff is of type SERV_EFF •time is a Date and is optional •date is a String •desc is a String
Example	Input RTRV-LOG:CISCO::123; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-3-1,12:CURRENT=MJ,PREVIOUS=CL,EOC,NSA,TIME=16-33-04, DATE=1971-02-03:\"SDCC TERMINATION FAILURE\"" ;
Errors	This message generates all the default errors

11.11.84 RTRV-NE: Retrieve Network Element

This command retrieves the attributes of the NE system such as the node identity (e.g. IP address), external interfaces (e.g. LAN ports), and major modes of operation (e.g. SONET vs. SDH).


Section	Description
Category	Other
Security	Read Only
Related Messages	N/A
Input Format	RTRV-NE:[TID]::[CTAG]::::;
Output Format	SID DATE TIME M CTAG COMPLD "IPADDR=<ipaddr>,IPMASK=<ipmask>,DEFRTR=<defrtr>, EXTLAN=<extlan>,INTLAN=<intlan>,RTRMDE=<rtrmode>, STM=<stm>,NODEID=<nodeid>,EXTRNG=<ext_ring>, RNGWTR=<rngwtr>,TMMD=<timing_mode>,SSMG=<sync_gen>, NSQL=<sync_quality_level>" ; where: •ipaddr is the IP address of the NE on the local LAN and is a String •ipmask is the IP Mask used to identify the sub-net on which the NE resides; ipmask is a String •defrtr is the IP address of the default router and is a String •extlan is of type EXT_LAN •intlan is of type EXT_LAN •rtrmode is of type EXT_LAN •stm is of type OPTICAL_MODE •nodeid is the Node ID of the NE in the BLSR and is an Integer •ext_ring is the node/ring that supports the extended K1/K2/K3 protocol for more than 16 nodes per BLSR; ext_ring is of type EXT_RING •rngwtr is an Integer •timing_mode is of type TIMING_MODE •sync_gen is of type SYNC_GENERATION •sync_quality_level is of type SYNC_QUALITY_LEVEL
Example	Input RTRV-NE:LAKEVILLE::233::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "IPADDR=192.168.100.52,IPMASK=255.255.255.0, DEFRTR=192.168.100.1,EXTLAN=OFF,INTLAN=OFF, RTRMDE=OFF,STM=SONET,NODEID=3,EXTRNG=N,RNGWTR=99, TMMD=LINE,SSMG=GEN1,NSQL=ABOVE-PRS" ;
Errors	This message generates all the default errors

11.11.85 RTRV-PM-<MOD2>: Retrieve Performance (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command retrieves the performance monitoring for specified card type.

Note Release 2.2.1 does not support the 48C value.


Section	Description
Category	Performance
Security	Read Only
Related Messages	INIT-REG-<MOD2> RTRV-TH-<MOD2> SET-TH-<MOD2>
Input Format	RTRV-PM-<MOD2>:[TID]:<aid>:[CTAG]::,,,,<tmpr>,,; where: •aid is the AID ALL and must not be null •tmpr is of type TMPR and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<aid>:<montype>,<monval>,<validity>,<location>,<tmpr>,<direction>" ; where: •aid is the AID ALL •montype is the monitored type ex CVL, ESL and is of type ALL_MONTYPE •monval is the monitored value and l is an Integer •validity is of type VALIDITY •location is the location far-end, near-end or both; location is of type LOCATION •tmpr is the time period 15 min, 1 hour or 1 day; tmpr is of type TMPR •direction is the direction receive, transmit or both; direction is of type DIRECTION
Example	Input RTRV-PM-T1:TID:AID:123::,,,,15MIN,,; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "AID:CVL,21,COMPL,FEND,15MIN,RCV,," ;
Errors	This message generates all the default errors

11.11.86 RTRV-SYNCN: Retrieve SYNCN

This command retrieves the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock. For each clock, up to three synchronization sources may be specified (e.g. PRIMARY, SECOND,THIRD).


Section	Description
Category	Synchronization
Security	Read Only
Related Messages	ED-SYNCN OPR-SYNCNCSW REPT ALM SYNCN REPT EVT SYNCN RTRV-ALM-SYNCN RTRV-COND-SYNCN
Input Format	RTRV-SYNCN:[TID]:<sync_aid>:[CTAG]::::; where: •sync_aid identifies the synchronization reference to retrieve and is the AID sync_ref; sync_ref is listable and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<sync_aid>:PRIMARY=<primary>,SECOND=<second>,THIRD=<third>" ; where: •sync_aid is the synchronization reference to be modified and is the AID sync_ref •primary is the AID syn_src •second is the AID syn_src •third is the AID syn_src
Example	Input RTRV-SYNCN:BOYES:SYNC-NE:234::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "SYNC-NE:PRIMARY=FAC-1-2,SECOND=FAC-2-2,THIRD=FAC-3-2;" ;
Errors	This message generates all the default errors

11.11.87 RTRV-T1: Retrieve T1

This command retrieves the DS-1 facilities configuration.


Section	Description
Category	Other
Security	Read Only
Related Messages	ED-T1 ED-T3 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-T1 RLS-LPBK-T3 RTRV-T3
Input Format	RTRV-T1:[TID]:<aid>:[CTAG]::::; where: •aid is the AID facility and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<aid>:STATE=<pst>,ID=<id>,LNCDE=<line_code>, FRMF=<fame_format>,LBO=<line_buildout>" ; where: •aid is the AID facility •pst is of type PST •id is a String •line_code is of type LINE_CODE •frame_format is of type FRAME_FORMAT •line_buildout is of type LINE_BUILDOUT
Example	Input RTRV-T1:TID:AID:1223::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "AID:STATE=OOS,ID=CISCO,LNCDE=AMI,FRMF=ESF,LBO=0-131" ;
Errors	This message generates all the default errors

11.11.88 RTRV-T3: Retrieve T3

This command retrieves the facilities properties of a DS-3 and a DS-3 transmux card.


Section	Description
Category	Other
Security	Read Only
Related Messages	ED-T1 ED-T3 OPR-LPBK-T1 OPR-LPBK-T3 RLS-LPBK-T1 RLS-LPBK-T3 RTRV-T1
Input Format	RTRV-T3:[TID]:<facility>:[CTAG]::::; where: •facility is the facility aid FAC-[SLOT]-[1..6] or FAC-[SLOT]-[1..12]; facility is the AID facility and must not be null
Output Format	SID DATE TIME M CTAG COMPLD "<facility>:LNTYPE=<lineType>,[LNCODE=<lineCode>],LBO=<lbo>: PST=<pst>" ; where: •facility is the facility aid FAC-[SLOT]-[1..6] or FAC-[SLOT]-[1..12] and is the AID facility. •lineType is the port line type and is of type DS_LINE_TYPE •lineCode is the port one code; lineCode is of type DS_LINE_CODE and is optional •lbo is the circuit line buildout and is of type E_LBO •pst is of type PST
Example	Input RTRV-T3:CISCO:FAC-1-2:123::::; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-1-2:LNTYPE=C-BIT,LNCODE=B3ZS,LBO=0-225:PST=IS" ;
Errors	This message generates all the default errors

11.11.89 RTRV-TH-<MOD2>: Retrieve Threshold (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command retrieves the threshold level.

Note Release 2.2.1 does not support STS48C and VT1.


Section	Description
Category	Performance
Security	Read Only
Related Messages	INIT-REG-<MOD2> RTRV-PM-<MOD2> SET-TH-<MOD2>
Input Format	RTRV-TH-<MOD2>:[TID]:<facility>:[CTAG]::<allMontype>,[<location>], [<tmpr>]; where: •facility is the aid type and is the AID ALL; facility must not be null •allMontype is the monitored type and is of type ALL_MONTYPE; allMontype must not be null •location is the location and is of type LOCATION; a null value is equivalent to "ALL" •tmpr is the time period and is of type TMPR; a null value is equivalent to "ALL"
Output Format	SID DATE TIME M CTAG COMPLD "<facility>,[<eqptType>]:<allMontype>,[<location>],,<thval>,[<tmpr>]" ; where: •facility is the aid and is the AID ALL •eqptType is of type EQPT_TYPE and is optional •allMontype is the monitored type and is of type ALL_MONTYPE •location is the location and is of type location; location is optional •thVal is the threshold value and is an Integer •tmpr is the time period and is of type TMPR; tmpr is optional
Example	Input RTRV-TH-T3:CISCO:FAC-1-3:1234::CVL,FEND,15MIN; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "FAC-1-3,DS3-12:CVL,FEND,,1,15MIN" ;
Errors	This message generates all the default errors

11.11.90 RTRV-TOD: Retrieve Time of Day

This command queries the NE and displays the system date and time at the instant when the command was executed. The time returned is in Coordinated Universal Time (UTC).


Section	Description
Category	Other
Security	Read Only
Related Messages	N/A
Input Format	RTRV-TOD:[TID]::[CTAG];
Output Format	SID DATE TIME M CTAG COMPLD "<year>,<month>,<day>,<hour>,<minute>,<second>,,<tmtype>" ; where: •year is an Integer •month is an Integer •day is an Integer •hour is an Integer •minute is an Integer •second is an Integer •tmtype is a String
Example	Input RTRV-TOD:CAZADERO::230; Output TID-000 98-06-20 14-30-00 M 001 COMPLD "1998,05,08,17,01,33,,UTC" ;
Errors	This message generates all the default errors

11.11.91 SET-TH-<MOD2>: Set Threshold (DS1, EC1, OC3, OC12, OC48, STS1, STS3C, STS12C, STS48C, T1, T3, VT1)

This command sets the threshold level.

Note Release 2.2.1 does not support STS48C.


Section	Description
Category	Performance
Security	Read/Write
Related Messages	INIT-REG-<MOD2> RTRV-TH-<MOD2> RTRV-PM-<MOD2>
Input Format	SET-TH-<MOD2>:[TID]:<facility>:[CTAG]::<allMontype>,<thVal>, [<location>],,[<tmpr>]; where: •facility is the aid and is the AID ALL •allMontype is the monitored value and is of type ALL_MONTYPE •thVal is the threshold value and is an Integer •location is the location and is of type LOCATION •tmpr is the time period and is of type TMPR
Example	Input SET-TH-T3:CISCO:FAC-1-1:123::CVL,12,NEND,,15MIN;
Errors	This message generates all the default errors

11.11.92 SET-TOD: Set Time of Day

This command sets the system date and time for the NE. The year should be entered using four digits while the hour should be entered using a 24-hour time period (i.e. military time).


Section	Description
Category	Other
Security	Read/Write
Related Messages	N/A
Input Format	SET-TOD:[TID]::[CTAG]::<year>,<month>,<day>,<hour>,<minute>,<second>,[<difference>]:[USEDST=<usedst>]; where: •year is the current calendar year and is an Integer •month is the month of the year and ranges from 01 to 12; month is an Integer •day is the day of the month and ranges from 01 to 31; day is an Integer •hour is the hour of the day and ranges from 00 to 59; hour is an Integer •minute is the minute of the hour and ranges from 00 to 59; minute is an Integer •second is the second of the minute and ranges from 00 to 59; second is an Integer •difference is the number of minutes behind UTC and is an Integer •usedst indicates if Daylight Saving Time is used and is of type USE_DST
Example	Input SET-TOD:CAZADERO::240::1998,05,08,13,18,55,480:USEDST=Y;
Errors	This message generates all the default errors

11.11.93 SW-DX-EQPT: Switch DX Equipment

This command instructs the NE to switch duplex equipment.


Section	Description
Category	Equipment
Security	N/A
Related Messages	DLT-EQPT REPT EVT EQPT DLT-FFP-EQPT RLS-PROTNSW-EQPT ED-FFP-EQPT RTRV-ALM-EQPT ENT-EQPT RTRV-COND-EQPT ENT-FFP-EQPT RTRV-EQPT OPR-PROTNSW-EQPT RTRV-FFP-EQPT REPT ALM EQPT
Input Format	SW-DX-EQPT:[TID]:<eqpt>:[CTAG]::[<dxModeOp>],; where: •eqpt is the AID eqpt •dxModeOp is of type DX_MODE_OP
Example	Input SW-DX-EQPT:CISCO:SLOT-1:123::FRCD,;
Errors	This message generates all the default errors

11.12 Access Identifiers

The Access Identification code (AID) directs an input command to its intended physical or data entity inside the NE. Equipment Modules and facilities are typical examples of entities addressed by the access code.

Table 11-13 Access Identifiers
AID	Patterns
bits	BITS-ALL BITS-{1,2}
ds-1	DS1-{1-6,12-17}-{1-6}-{1-28}
env	ENV-IN-{1-4}
eqpt	SLOT-{1-17} SLOT-{1-6,12-17}
facility	FAC-{1-6,12-17}-1 FAC-{1-6,12-17}-{1-12} FAC-{1-6,12-17}-{1-14} FAC-{1-6,12-17}-{1-4} FAC-{1-6,12-17}-{1-6} FAC-{5,6,12,13}-1
sts	STS-{1-6,12-17}-1 STS-{1-6,12-17}-{1,4,7,10-46} STS-{1-6,12-17}-{1-12} STS-{1-6,12-17}-{1-6} STS-{5,6,12,13}-{1,13,25,37} STS-{5,6,12,13}-{1,4,7,10-46} STS-{5,6,12,13}-{1-48} STS-{5,6,12,13}-{1}
syn_src	FAC-{1-6,12-17}-1 FAC-{1-6,12-17}-{1-4} FAC-{5,6,12,13}-1 INTERNAL SYNC-NE SYNC-{BITS1,BITS2}
sync_ref	SYNC-NE SYNC-{BITS1,BITS2}
vt1_5	VT1-{1-6,12-17}-1-{1-14} VT1-{1-6,12-17}-{1-12}-{1-28} VT1-{1-6,12-17}-{1-6}-{1-28} VT1-{5,6,12,13}-{1-48}-{1-28}

11.12.1 bits

Table 11-14 bits
Pattern	Description
BITS-ALL	BITS-1 and BITS-2
BITS-{1,2}	Individual BITS AID

11.12.2 ds-1

Used to access the DS-1 frame layer of the DS3XM-6

Table 11-15 ds-1
Pattern	Description
DS1-{1-6,12-17}-{1-6}-{1-28}	DS-1 aid for a DX3Xm card

11.12.3 env

The AIC card environmental AIDs

Table 11-16 env
Pattern	Description
ENV-{IN}-{1-4}	Environmental alarm aid

11.12.4 eqpt

Table 11-17 eqpt
Pattern	Description
SLOT-{1-17}	Equipment aid for the whole NE
SLOT-{1-6,12-17}	Equipment aid for the I/O slots

11.12.5 facility

Used to access specific ports

Table 11-18 facility
Pattern	Description
FAC-{1-6,12-17}-1	Facility aid for the OC-12
FAC-{1-6,12-17}-{1-12}	Facility aid for the EC-1 and DS-3 cards
FAC-{1-6,12-17}-{1-14}	Facilities for the DS-1 card
FAC-{1-6,12-17}-{1-4}	Facility aid for the OC-3 card
FAC-{1-6,12-17}-{1-6}	Facility aid for the DS3XM card
FAC-{5,6,12,13}-1	Facility aid for the OC-48 card

11.12.6 sts

SONET frame-level AID set

Table 11-19 sts
AID	Description
STS-{1-6,12-17}-1	STS-1 aid for DS-1 cards STS-3C aid for OC-3 cards STS-12C aid for OC-12 cards
STS-{1-6,12-17}-{1,4,7,10}	STS-3C aid for OC-3 and OC-12 cards
STS-{1-6,12-17}-{1-12}	STS-1 aid for OC-12, EC-1, DS-3 and OC-3 cards
STS-{1-6,12-17}-{1-6}	STS-1 aid for DS3XM cards
STS-{5,6,12,13}-{1,13,25,37}	STS-12C for OC-48
STS-{5,6,12,13}-{1,4,7,10,13,16,19,22, 25,28,31,34,37,40,43,46}	STS-3C for OC-48
STS-{5,6,12,13}-{1-48}	STS-1 for OC-48
STS-{5,6,12,13}-{1}	STS-48C for OC-48

11.12.7 syn_src

Synchronization source

Table 11-20 sync_src
Pattern	Description
FAC-{1-6,12-17}-1	Sync source is the optical card (OC-12) facility
FAC-{1-6,12-17}-{1-4}	Sync source is the optical card (OC-3) facility
FAC-{5,6,12,13}-1	Sync source is the optical card (OC-48) facility
INTERNAL	Set the syn_src to be the system default value
SYNC-NE	Sync-NE source
SYNC-{BITS1,BITS2}	SYNC-BITS1 or SYNC-BITS2 sync source

11.12.8 sync_ref

Synchronization aids

Table 11-21 sync_ref
Pattern	Description
SYNC-NE	NE sync aid
SYNC-{BITS1,BITS2}	BITS1 and BITS2 sync aids

11.12.9 vt1_5

Virtual termination aids

Table 11-22 vt1_5
Pattern	Description
VT1-{1-6,12-17}-1-{1-14}	DS-1 vts
VT1-{1-6,12-17}-{1-12}-{1-28}	OC-12, OC-3, EC-1 vts
VT1-{1-6,12-17}-{1-6}-{1-28}	DS3XM vts
VT1-{5,6,12,13}-{1-48}-{1-28}	OC-48 vts

11.13 Parameter Types

This section provides a description of all message parameter types defined for the TL1 messages used in the ONS 15454. The TL1 message descriptions frequently refer to this section.

11.13.1 ATAG Description

The Autonomous Message Tag (ATAG) is used for message sequencing. The number is incremented by one for each autonomous message sent by the ONS 15454. The ONS 15454 uses whole numbers 0000 to 9999.

11.13.2 CTAG Description

The Correlation tag is included in each command by the user and is repeated by the ONS 15454 in the response to allow the user to associate the command and response messages.

Note The valid values for a ctag are decimal numbers with a maximum of 6 digits in Release 2.2.1.

11.13.3 TID Description

The Target Identifier is the name of the NE where the command is addressed. TID is the Telcordia name for the system.

11.13.4 ALL_MONTYPE

Monitoring type list

Table 11-23 ALL_MONTYPE Values
ALL_MONTYPE Values	Description
AISSP	Alarm Indication Signal Seconds-Path
CVCPP	Coding Violations - CP-Bit Path
CVL	Coding Violations - Line
CVP	Coding Violations - Path
CVV	Coding Violations - Section
ESCPP	Errored Seconds - CP-Bit Path
ESL	Errored Seconds - Line
ESP	Errored Seconds - Path
ESV	Errored Seconds - VT Path
FCL	Failure Count - Line
FCP	Failure Count - Path
LOSSL	Loss of Signal Seconds - Line
NPJC-PDET	PPJC-PDET:Negative Pointer Justification
NPJC-PGEN	PPJC-PDEN:Negative Pointer Justification
PPJC-PDET	PPJC-PDET:Positive Pointer Justification
PPJC-PGEN	PPJC-PDEN:Positive Pointer Justification
PSC	Protection Switching Count
PSD	Protection Switching Duration
SASCPP	Severely Errored Framing/AIS Second - CP-Bit Path
SASP	Severely Errored Framing/AIS Seconds
SEFS	Severely Errored Framing Seconds
SESCPP	Severely Errored Second - CP-Bit Path
SESL	Severely Errored Second - Line
SESP	Severely Errored Second - Path
SESV	Severely Errored Second - VT Path
UASCPP	Unavailable Second - CP-Bit Path
UASL	Unavailable Second - Line
UASP	Unavailable Second - Path
UASV	Unavailable Second - VT Path

11.13.5 ALL_THR

Threshold list

Table 11-24 ALL_THR Value
ALL_THR Values	Description
T-AISSP	Alarm Indication Signal Seconds-Path
T-CVCPP	Coding Violations - CP-Bit Path
T-CVL	Coding Violations - Line
T-CVP	Coding Violations - Path
T-CVS	Coding Violations - Section
T-CVV	Coding Violations - VT Path
T-ESCPP	Errored Seconds - CP-Bit Path
T-ESL	Errored Seconds - Line
T-ESP	Errored Seconds - Path
T-ESS	Errored Seconds - Section
T-ESV	Errored Seconds - VT Path
T-FCL	Failure Count - Line
T-FCP	Failure Count - Path
T-LOSSL	Loss of Signal Seconds - Line
T-PJNEG	PPJC-PDET:Negative Pointer Justification
T-PJNEG-GEN	PPJC-PGEN:Negative Pointer Justification
T-PJPOS	PPJC-PDET:Positive Pointer Justification
T-PJPOS-GEN	PPJC-PGEN:Positive Pointer Justification
T-PSC	Protection Switching Count
T-PSD	Protection Switching Duration
T-SASCPP	Severely Errored Framing/AIS Second - CP-Bit Path
T-SASP	Severely Errored Framing/AIS Seconds
T-SEFS	Severely Errored Framing Seconds
T-SESCPP	Severely Errored Second - CP-Bit Path
T-SESL	Severely Errored Second - Line
T-SESP	Severely Errored Second - Path
T-SESS	Severely Errored Second - Section
T-SESV	Severely Errored Second - VT Path
T-UASCPP	Unavailable Second - CP-Bit Path
T-UASL	Unavailable Second - Line
T-UASP	Unavailable Second - Path
T-UASV	Unavailable Second - VT Path

11.13.6 CCT

Defines the type of cross-connect to be created.

Table 11-25 CCT Values
CCT Values	Description
1WAY	A unidirectional connection from a source tributary to a destination tributary
2WAY	A bidirectional connection between the two tributaries
MON	Monitored cross connection

11.13.7 COND_EFF

The affected unit's condition

Table 11-26 COND_EFF Values
COND_EFF Values	Description
CL	Standing condition cleared
SC	Standing condition raised
TC	Transient condition

11.13.8 CONDITION

The condition type of the alarm indication

Table 11-27 CONDITION Values
CONDITION Values	Description
ACOMAN	Alarm cutoff is in manual mode
AIS	External failure - Incoming - Alarm Indication Signal
AIS-L	External failure - Incoming - Alarm Indication Signal - Line
AIS-P	External failure - Incoming - Alarm Indication Signal - Path
AIS-V	External failure - Incoming - Alarm Indication Signal - VT layer
APSB	External failure - Incoming - Automatic Protection Switching Channel - Byte failure
APSC	External failure - Incoming - Automatic Protection Switching Channel failure
APSC-IMP	External failure - Incoming - Automatic Protection Switching - Invalid K bytes
APSCCONNL	External failure - Incoming - Automatic Protection Switching - Connection Loss
APSCDFLTK	External failure - Incoming - Automatic Protection Switching - Default K byte
APSCINCON	External failure - Incoming - Automatic Protection Switching - Inconsistent
APSCM	External failure - Incoming - Automatic Protection Switching Channel - Protection Switching Channel Match failure
APSCNMIS	APS Channel - BLSR - Node ID Mismatch
APSMM	External failure - Incoming - Automatic Protection Switching Channel - Automatic Protection Switch Mode Mismatch
AUTOLSROFF	Internal hardware - Facility Termination Equipment - Automatic Laser Shutdown
AUTORESET	Recovery action - Automatic System Reset
AUTOSW-AIS	Automatic Switch - Alarm Indication Signal
AUTOSW-LOP	Automatic Switch - Loss of Pointer
AUTOSW-PDI	Automatic Switch - Payload Defect Indication
AUTOSW-SDBER	Automatic Switch - Signal Degrade Bit Error Rate
AUTOSW-SFBER	Automatic Switch - Signal Fail Bit Error Rate
AUTOSW-UNEQ	Automatic Switch - Unequipped
BKUPMEMP	Internal hardware - Control Equipment - Primary Non-Volatile Backup Memory Failure
BKUPMEMS	Internal hardware - Control Equipment - Secondary Non-Volatile Backup Memory Failure
BLSR-RESYNC	Bidirectional Line Switched Ring - Tables Resynchronized
BLSROOSYNC	Bidirectional Line Switched Ring - Out of Sync
BPV	External failure - Incoming - Bipolar Violation
CARLOSS	External failure - Incoming - Carrier Loss on the LAN
CLDRESTART	Recovery action - Cold Restart
CONCAT	STS Concatenation Error
CONTBUS	Control Bus Failure
CONTBUS-1	Control Bus Failure - 1
CONTBUS-2	Control Bus Failure - 2
CONTBUS-A-1	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 1
CONTBUS-A-2	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 2
CONTBUS-A-3	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 3
CONTBUS-A-4	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 4
CONTBUS-A-5	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 5
CONTBUS-A-6	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 6
CONTBUS-A-7	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 7
CONTBUS-A-8	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 8
CONTBUS-A-9	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 9
CONTBUS-A-10	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 10
CONTBUS-A-11	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 11
CONTBUS-A-12	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 12
CONTBUS-A-13	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 13
CONTBUS-A-14	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 14
CONTBUS-A-15	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 15
CONTBUS-A-16	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 16
CONTBUS-A-17	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 17
CONTBUS-A-18	TCC/TCC+ card in Slot 7 has lost communication with the card in Slot 18
CONTBUS-B-1	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 1
CONTBUS-B-2	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 2
CONTBUS-B-3	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 3
CONTBUS-B-4	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 4
CONTBUS-B-5	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 5
CONTBUS-B-6	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 6
CONTBUS-B-7	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 7
CONTBUS-B-8	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 8
CONTBUS-B-9	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 9
CONTBUS-B-10	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 10
CONTBUS-B-11	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 11
CONTBUS-B-12	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 12
CONTBUS-B-13	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 13
CONTBUS-B-14	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 14
CONTBUS-B-15	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 15
CONTBUS-B-16	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 16
CONTBUS-B-17	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 17
CONTBUS-B-18	TCC/TCC+ card in Slot 11 has lost communication with the card in Slot 18
CONTCOM	Internal hardware - Control Equipment - Control Communications equipment failure
CONTEQPT	Internal hardware - Control Equipment failure
CONTR	Internal hardware - Control Equipment - Control processor failure
CTNEQPT	Internal hardware - Interconnection Equipment failure
CTNEQPT-PB1PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 1
CTNEQPT-PB1WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 1
CTNEQPT-PB2PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 2
CTNEQPT-PB2WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 2
CTNEQPT-PB3PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 3
CTNEQPT-PB3WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 3
CTNEQPT-PB4PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 4
CTNEQPT-PB4WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 4
CTNEQPT-PB5PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 5
CTNEQPT-PB5WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 5
CTNEQPT-PB6PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 6
CTNEQPT-PB6WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 6
CTNEQPT-PB12PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 12
CTNEQPT-PB12WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 12
CTNEQPT-PB13PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 13
CTNEQPT-PB13WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 13
CTNEQPT-PB14PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 14
CTNEQPT-PB14WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 14
CTNEQPT-PB15PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 15
CTNEQPT-PB15WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 15
CTNEQPT-PB16PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 16
CTNEQPT-PB16WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 16
CTNEQPT-PB17PROT	Failure of the main payload between the protect XC/XCVT card in Slot 10 and the reporting I/O card in Slot 17
CTNEQPT-PB17WORK	Failure of the main payload bus between the active XC/XCVT card in Slot 8 and the reporting I/O card in Slot 17
DATAFLT	Internal Error - Software Fault - Data integrity fault
EOC	Embedded Operations Channel (Section DCC) failure
EOC-DOWN	Embedded Operation Channel Fail
EQPT	Internal hardware - Critical alarm caused by equipment failure
EQPT-DIAG	Equipment failure - Diagnostics Failure
EQPT-FAIL	Equipment Failure - Board Failure
EQPT-MAC	Equipment Failure - Medium Access Control
ESW	External Error - Excessive Switching
EXCCOL	External Failure - Incoming - Excess collisions on the LAN
EXT	Failure Detected External to the NE
EXTERR	External Error
FA	Internal Hardware - Power Failure - Fuse Alarm
FAC	External failure - Incoming - Facility, critical alarm caused by DS-3 facility failure
FACTERM	Internal hardware - Facility Termination equipment failure
FAILTORLS	Internal hardware - Failure To Release from protection
FAILTOSW	Internal hardware - Failure To Switch to protection
FAILTOSW-PATH	Failure to switch from the working path to the protection path on a UPSR
FAILTOSWR	Failure to Switch to Protection in a Ring
FAILTOSWS	Failure to Switch to Protection in a Span
FAN	Fan Tray Failure
FE-AIS	Far-end DS-3 node is reporting an AIS
FE-DS1-MULTLOS	Multiple inputs detect a loss on the far-end
FE-DS1-NSA	Non-service affecting failure detected from the far-end DS-1
FE-DS1-SA	Service affecting failure detected from the far-end DS-1
FE-DS1-SNGLLOS	One of the DS-1 inputs on the far-end detects a LOS
FE-DS3-NSA	Non-service affecting failure detected from the far-end DS-3
FE-DS3-SA	Service affecting failure detected from the far-end DS-3
FE-EQPT-NSA	Non-service affecting equipment failure is detected from the far-end DS-3
FE-IDLE	Far-end node detects an idle DS-3 signal
FE-LOF	Far-end node reports a DS-3 loss of frame
FE-LOS	Far-end node reports a DS-3 loss of signal
FEBE	External failure - Incoming - Far End Block Error
FEPRLF	External failure - Incoming - Automatic Protection Switching Channel - Far End Protection Line Failure
FORCED-REQ	Forced switch request on facility/equipment
FRCDWKSWBK	Recovery action - Working facility/equipment forced to switch back to working
FRCDWKSWPR	Recovery action - Working facility/equipment forced to switch to protection unit
FRCDWKSWPR-PATH	Recovery action - Working facility/equipment forced to switch to protection unit - Path
FRCWKBK-R	Recovery action - Working facility/equipment forced to switch back to working - Ring
FRCWKBK-S	Recovery action - Working facility/equipment forced to switch back to working - Span
FRCWKPR-R	Recovery action - Working facility/equipment forced to switch to protection unit- Ring
FRCWKPR-S	Recovery action - Working facility/equipment forced to switch to protection unit- Span
FRNGSYNC	Free Running Synchronization mode
FSTSYNC	Fast Start Synchronization Mode
HITEMP	Internal hardware - Equipment failure - High temperature
HLDOVRSYNC	Holdover synchronization mode
IMPROPRMVL	Procedural Error - Improper Removal
INC	Incoming failure condition
INC-ISD	Incoming failure condition - Idle Signal Path
INIT	Recovery action - Initialization initiated
INT	Internal hardware fault or failure
INTERR	Error Internal to the NE Detected
INTMSGERR	Internal Error - Internal Message Error
INTSFT	Internal Error - Software Fault or failure
INVMACADR	Equipment Failure - Invalid MAC address
LKOUTPR-R	Lockout or Protection - Ring
LKOUTPR-S	Lockout or Protection - Span
LKOUTWK-R	Lockout of Working - Ring
LKOUTWK-S	Lockout of Working - Span
LOCKOUT-REQ	Lockout switch request on facility/equipment
LOCKOUTOFPR	Recovery action - Lockout of Protection
LOCKOUTOFPR-PATH	Recovery action - Lockout of Protection - Path
LOCKOUTOFWK	Recovery action - Lockout of working
LOF	External failure - Incoming - Loss of Frame
LOP	External failure - Incoming - Loss of Pointer
LOP-P	External failure - Incoming - Loss of Pointer - Path
LOP-V	Loss of pointer at the VT level
LOS	External failure - Incoming - Loss of Signal
LPBK	Loopback
LPBKDS1FEAC	DS-1 loopback signal is received from the far-end due to a Far-End Alarm and Control (FEAC) command
LPBKDS1FEAC-CMD	DS-1 loopback command sent by the ONS 15454 to the far-end equipment
LPBKDS3FEAC	DS-3 loopback signal is received from the far-end due to a Far-End Alarm and Control (FEAC) command
LPBKDS3FEAC-CMD	DS-3 loopback command sent by the ONS 15454 to the far-end equipment
LPBKFACILITY	Loopback, Facility
LPBKM23	DS-2 Loopback due to Far End Command
LPBKM23-CMD	DS-2 Loopback Command sent to Far End
LPBKNETWORK	Loopback, Network
LPBKTERMINAL	Loopback, Terminal
MAN	Manually caused abnormal condition
MAN-REQ	Manual Switch Request
MANRESET	Recovery action - Manual system Reset
MANSWTOINT	Recovery action - Manual synchronization switch to internal clock
MANSWTOPRI	Recovery action - Manual synchronization Switch To Primary reference
MANSWTOSEC	Recovery action - Manual synchronization Switch To Second reference
MANSWTOTHIRD	Recovery action - Manual synchronization Switch To Third reference
MANSWTOFOURTH	Recovery action - Manual synchronization Switch To Fourth reference
MANSWTOFIFTH	Recovery action - Manual synchronization Switch To Fifth reference
MANSWTOSIXTH	Recovery action - Manual synchronization Switch To Sixth reference
MANWKBK-R	Manual Switch of working facility/equipment to protection - Ring
MANWKBK-S	Manual Switch of working facility/equipment to protection - Span
MANWKPR-R	Manual Switch of working facility/equipment to protection unit - Ring
MANWKPR-S	Manual Switch of working facility/equipment to protection unit - Span
MANWKSWBK	Recovery action - Manual Switch or working facility/equipment to protection
MANWKSWPR	Recovery action - Manual Switch of Working facility/equipment to protection unit
MANWKSWPR-PATH	Recovery action - Manual Switch of Working facility/equipment to protection - Path
MEA	Internal error - Mismatch of Equipment and Attributes
MEM-GONE	Software operations exceed the memory capacity of the TCC/TCC+ card
MEM-LOW	Data generated by software operations is close to exceeding the memory capacity of the TCC/TCC+ card
NEW-ROOT	New root trap in BRIDGE-MIB
NORMAL	Normal condition - This condition type is used by the NE to report the returning to normal from a previous off-normal condition
OG	External failure - Outgoing failure condition
OOF	External failure - Incoming - Out of Frame
PATHSEL	External failure - Incoming - Path Selector inability to switch to a valid signal
PDI	External failure - Incoming - Signal Label Mismatch Failure - Payload Defect Indication
PDI-P	External failure - Incoming - Signal Label Mismatch Failure - Payload Defect Indication - Path
PEERMISSM	Peer state mismatch
PLM-P	External failure - Incoming - Signal Label Mismatch Failure - Payload Label Mismatch - Path
PLM-V	Content of the V5 byte in the SONET overhead is inconsistent or invalid
PLUG-IN	Internal hardware - Equipment unit plug-in
PM-TCA	Performance Monitoring - Threshold Crossing Alert
PRC-DUPID	Procedural Error - Duplicate Node ID
PRCDRERR	Procedural Error
PROGFLT	Internal Error - Software Fault - Program failure
PROTNA	Protection unit not available
PS	Occurrence of a protection switching event
PWR	Internal hardware - Power failure (detected internal to NE)
PWRRESTART	Recovery action - Powerfail Restart
RAI	External failure - Incoming - Remote Alarm Indication
RCVR	Internal hardware - Facility Termination equipment - Receiver failure
RCVR-MISS	Facility termination equipment detects a missing receive cable on the DS-1 port or a possible mismatch of backplane equipment
RCVRY	Recovery or service protection action has been initiated
RDI-L	External failure - Outgoing - Remote Defect Indication - Line
RDI-P	External failure - Outgoing - Remote Defect Indication - Path
RFI	External failure - Incoming - Remote Failure Indication
RFI-L	External failure - Incoming - Remote Failure Indication - Line
RFI-P	External failure - Incoming - Remote Failure Indication - Path
RFI-V	Upstream failure has occurred at the VT layer
RMON-ALARM	An RMON Alarm
RMON-RESET	RMON histories and alarms have been reset due to chipset reboot
SD	Facility has passed BER Threshold for Signal Degrade
SEF	External failure - Incoming - Severely Errored Frame
SF	Facility has passed BER threshold for Signal Failure
SLMF	External failure - Incoming - Signal Label Mismatch Failures - SONET
SQUELCH	Ring is isolated into two or more segments
SSM-DUS	Synchronization Status Messaging - Don't use for timing synchronization
SSM-FAIL	Synchronization Status Messaging - Failed
SSM-OFF	Synchronization Status Messaging - Off
SSM-PRS	Synchronization Status Messaging - Primary reference source - Stratum 1
SSM-RES	Synchronization Status Messaging - Reserved - quality level set by user
SSM-SMC	Synchronization Status Messaging - SONET minimum clock
SSM-ST2	Synchronization Status Messaging - Stratum 2
SSM-ST3	Synchronization Status Messaging - Stratum 3
SSM-ST3E	Synchronization Status Messaging - Stratum 3E
SSM-ST4	Synchronization Status Messaging - Stratum 4
SSM-STU	Synchronization Status Messaging - Sync traceability unknown
SSM-TNC	Synchronization Status Messaging - Transit node clock
SWFTDWN	Recovery action - Software download in progress
SWTOINT	Recovery action - Synchronization Switch To Internal clock
SWTOPRI	Recovery action - Synchronization Switch To Primary reference
SWTOSEC	Recovery action - Synchronization Switch To Second reference
SWTOTHIRD	Recovery action - Synchronization Switch To Third reference
SWTOFOURTH	Recovery action - Synchronization Switch To Fourth reference
SWTOFIFTH	Recovery action - Synchronization Switch To Fifth reference
SWTOSIXTH	Recovery action - Synchronization Switch To Sixth reference
SYNC	External failure - Incoming - Loss of timing on Synchronization link.
SYNCCLK	Internal hardware - Synchronization unit failure
SYNCEQPT	Internal hardware - Synchronization switching Equipment failure
SYNCOOS	External failure - Incoming - Loss of timing on all specified synchronization links
SYNCPRI	External failure - Incoming - Loss of timing on primary synchronization link
SYNCSEC	External failure - Incoming - Loss of timing on secondary synchronization link
SYNCTHIRD	External failure - Incoming - Loss of timing on third synchronization link
SYNCFOURTH	External failure - Incoming - Loss of timing on fourth synchronization link
SYNCFIFTH	External failure - Incoming - Loss of timing on fifth synchronization link
SYNCSIXTH	External failure - Incoming - Loss of timing on sixth synchronization link
SYSBOOT	Activation of new software
TOP-CHANGE	Topology Change trap in BRIDGE-MIB
TRMT	Internal hardware - Facility Termination equipment - Transmit failure
TRMT-MISS	Facility termination equipment detects a missing transmit cable on the DS-1 port or a possible mismatch of backplane equipment
TSI	Internal hardware - Interconnection Equipment - Time slot interchange equipment failure
UNEQ-P	External failure - Incoming - Signal Label Mismatch Failure - Unequipped - Path
UNEQ-V	VT is receiving an unequipped signal
UNPLUG	Internal hardware - Equipment unit un-plug
WATM-TO	Internal Error - Watchdog Timer Timeout
WKGMEM	Internal hardware - Control Equipment -Working memory failure
WKSWBK	Recovery action - Working facility/equipment switched back to working
WKSWPR	Recovery action - Working facility/equipment switched to protection unit
WRMRESTART	Recovery action - Warm Restart
WTR	Recovery action - SONET line is in Wait To Restore state

11.13.9 DIRECTION

Transmit and receive directions

Table 11-28 DIRECTION Values
DIRECTION Values	Description
BTH	Both transmit and receive directions
RCV	Receive direction only
TRMT	Transmit direction only

11.13.10 DS3_FMT

Indicates a DS-3 digital signal format

Table 11-29 DS3_FMT Values
DS3_FMT Values	Description
ASYNC	The DS-3 digital signal format is ASYNC
CBIT	The DS-3 digital signal format is C-BIT
SYNC	The DS-3 digital signal format is SYNC
UNFR	The DS-3 digital signal format is unframed

11.13.11 DS_LINE_CODE

DS-123 Line Code

Table 11-30 DS_LINE_CODE Values
DS_LINE_CODE Values	Description
B3ZS	Bipolar with Three-Zero Substitution

11.13.12 DS_LINE_TYPE

DS-123 Line type

Table 11-31 DS_LINE_TYPE Values
DS_LINE_TYPE Values	Description
C-BIT	C-BIT line type applies to DS3XM card
M23	M23 line type applies to DS3XM card
UNFRAMED	Line Type is Unframed

11.13.13 DX_MODE_OP

Duplex switch operation mode

Table 11-32 DX_MODE_OP Values
DX_MODE_OP Values	Description
FRCD	Forced Switch
MAN	Manual Switch

11.13.14 E_LBO

Electrical signal line buildout

Table 11-33 E_LBO Values
E_LBO Values	Description
0-225	Electrical signal buildout range is 0-255
226-450	Electrical signal buildout range is 255-450

11.13.15 ENV_ALM

Environmental alarm types as defined by Telcordia GR-833-CORE, Issue 2, November 1996, Appendix F.

Table 11-34 ENV_ALM Values
ENV_ALM Values	Description
AIRCOMPR	Air compressor failure
AIRCOND	Air conditioning failure
AIRDRYR	Air dryer failure
BATDSCHRG	Battery discharging
BATTERY	Battery failure
CLFAN	Cooling fan failure
CPMAJOR	Centralized power major failure
CPMINOR	Centralized power minor failure
ENGINE	Engine failure
ENGOPRG	Engine operating
EXPLGS	Explosive gas
FIRDETR	Fire detector failure
FIRE	Fire
FLOOD	Flood
FUSE	Fuse failure
GEN	Generator failure
HIAIR	High airflow
HIHUM	High humidity
HITEMP	High temperature
HIWTR	High water
INTRUDER	Intrusion
LWBATVG	Low battery voltage
LWFUEL	Low fuel
LWHUM	Low humidity
LWPRES	Low cable pressure
LWTEMP	Low temperature
LWWTR	Low water
MISC	Miscellaneous
OPENDR	Open door
POWER	Commercial power failure
PUMP	Pump failure
PWR-48	48 Volt power supply failure
RECT	Rectifier failure
RECTHI	Rectifier high voltage
RECTLO	Rectifier low voltage
SMOKE	Smoke
TOXICGAS	Toxic gas
VENTN	Ventilation system failure

11.13.16 ENV_CTL

Environmental control types as defined by Telcordia GR-833-CORE, Issue 2, November 1996, Appendix G.

Table 11-35 ENV_CTL Values
ENV_CTL Values	Description
AIRCOND	Air conditioning
ENGINE	Engine
FAN	Fan
GEN	Generator
HEAT	Heat
LIGHT	Light
MISC	Miscellaneous
SPKLR	Sprinkler

11.13.17 EQPT_TYPE

Identifies the type of equipment being provisioned into a slot.

Table 11-36 EQPT_TYPE Values
EQPT_TYPE Values	Description
AIC	The Alarm Interface Controller Card is an optional card which expands system management capabilities for the customer defined alarm I/O and orderwire functionality
DCC	The Data Communications Channel communicates network management information
DS1-14	A 14 port interface card supporting DS-1 facilities
DS1N-14	A 14 port interface card supporting DS-1 facilities
DS3-12	A 12 port interface card supporting DS-3 facilities
DS3CR-12	Cost reduced DS-3
DS3N-12	A 12 port interface card supporting DS-3 facilities
DS3XM-6	An interface card that converts six framed DS-3 network connections to 28x6 or 168 VT1.5s
E1000T-2	A two port interface card supporting 1000 Base T ethernet facilities
E100T-12	A 12 port interface card supporting 100 Base T ethernet facilities
EC1-12	A 12 port interface card supporting EC-1 facilities
EC1N-12	A 12 port interface card supporting EC-1 facilities
OC-12	An interface card that supports one or more OC-12 (622Mbs) optical facilities
OC12-IR-1	An interface card that supports one intermediate range OC-12 (622Mbs) optical facilities
OC12-LR-1	An interface card that supports one long range OC-12 (622Mbs) optical facilities
OC12-SR-1	An interface card that supports one short range OC-12 (622Mbs) optical facilities
OC192-LR-1	An interface card that supports one or more long range OC-192 optical facilities
OC-3	An interface card that supports multiple OC-3 (155Mbs) optical facilities
OC3-IR-4	An interface card that supports four intermediate range OC-3 (155Mbs) optical facilities
OC3-SR-4	An interface card that supports four short range OC-3 (155Mbs) optical facilities
OC-48	An interface card that supports one or more OC-48 (10Gbs) optical facilities
OC48-IR-1	An interface card that supports one intermediate range OC-48 (10Gbs) optical facilities
OC48-LR-1	An interface card that supports one long range OC-48 (10Gbs) optical facilities
OC48-SR-1	An interface card that supports one short range OC-48 (10Gbs) optical facilities
TCC	The Timing, Communication and Control card
TCC+	The Timing, Communication and Control+ card
XC	A Cross-Connect card
XC-192	A Cross-Connect card
XC-VT	A Cross-Connect card

11.13.18 EQUIP

Indicates the presence of a plug-in unit

Table 11-37 EQUIP Values
EQUIP Values	Description
EQUIP	The unit is Equipped - present
UNEQUIP	The unit is Unequipped - absent

11.13.19 EQUIPMENT_TYPE

Table 11-38 EQUIPMENT_TYPE Values
EQUIPMENT_TYPE Values	Description
AIC	AIC card
DS-1	DS-1 card
DS-1N	DS-1N card
DS-3	DS-3 card
DS-3N	DS-3N card
DS3XM	DS3XM card
E-100T	E-100T card
E-1000T	E-1000T card
EC-1	EC-1 card
EC-1N	EC-1N card
OC-12	OC-12 card
OC-3	OC-3 card
OC-48	OC-48 card
TCC	TCC card
TCC+	TCC+ card
XC-STS	XC-STS card
XC-VT	XC-VT card

11.13.20 EXT_RING

Indicates if the ring supports the extended K1/K2/K3 protocol.

Table 11-39 EXT_RING Values
EXT_RING Values	Description
N	Indicates the Ring does not support the extended K1/K2/K3 protocol
Y	Indicates the Ring does support the extended K1/K2/K3 protocol

11.13.21 FRAME_FORMAT

The frame format for a T1 port

Table 11-40 FRAME_FORMAT Values
FRAME_FORMAT Values	Description
D4	Frame format is D4
ESF	Frame format is ESF
UNFRAMED	Frame format is unframed

11.13.22 LINE_BUILDOUT

Table 11-41 LINE_BUILDOUT Values
LINE_BUILDOUT Values	Description
0-131	Line buildout range is 0-131
132-262	Line buildout range is 132-262
263-393	Line buildout range is 263-393
394-524	Line buildout range is 394-524
525-655	Line buildout range is 525-655

11.13.23 LINE_CODE

Table 11-42 LINE_CODE Values
LINE_CODE Values	Description
AMI	Line code value is AMI
B8ZS	Line code value is B8ZS (Bipolar with Eight-Zero Substitution)

11.13.24 LOCATION

Identifies the location where the action is to take place

Table 11-43 LOCATION Values
LOCATION Values	Description
FEND	Action occurs on the Far End of the facility
NEND	Action occurs on the Near End of the facility

11.13.25 LPBK_TYPE

Indicates the type of loopback that is to be operated or released

Table 11-44 LPBK_TYPE Values
LPBK_TYPE Values	Description
FACILITY	A type of loopback that connects the incoming received signal immediately following the optical-to-electrical conversion (before descrambling) to the associated transmitter in the return direction
TERMINAL	A loopback that connects the signal that is about to be transmitted (after scrambling but before the electrical-to-optical conversion) is connected to the associated, incoming receiver

11.13.26 MOD2

A generic object type

Table 11-45 MOD2 Values
MOD2 Values	Description
DS-1	DS-1 facility on DS3XM
EC-1	EC-1 facility
OC-12	OC-12 facility
OC-3	OC-3 facility
OC-48	OC-48 facility
STS-1	STS path
STS-12C	STS path
STS-3C	STS path
STS-48C	STS path
T1	DS-1 facility
T3	DS-3 facility
VT1	VT1 path

11.13.27 MOD2ALM

Alarm type for certain generic TL1 commands

Table 11-46 MOD2ALM Values
MOD2ALM Values	Description
DS-1	DS-1 alarm
E-100	E-100 alarm
E-1000	E-1000 alarm
EC-1	EC-1 alarm
OC-12	OC-12 alarm
OC-3	OC-3 alarm
OC-48	OC-48 alarm
STS-1	STS-1 alarm
STS-12C	STS-12C alarm
STS-3C	STS-3C alarm
STS-48C	STS-48C alarm
T1	T1 alarm
T3	T3 alarm
VT1	VT1 alarm

11.13.28 MOD2B

Alarm type for certain generic TL1 commands

Table 11-47 MOD2B Values
MOD2B Values	Description
BITS	BITS alarm
COMM	COMM alarm
DS-1	DS-1 alarm
E-100	E-100 alarm
E-1000	E-1000 alarm
EC-1	EC-1 alarm
ENV	ENV alarm
EQPT	EQPT alarm
OC-12	OC-12 alarm
OC-3	OC-3 alarm
OC-48	OC-48 alarm
STS-1	STS alarm
STS-12C	STS alarm
STS-3C	STS alarm
STS-48C	STS alarm
SYNCN	SYNCN alarm
T1	T1 alarm
T3	T3 alarm
TCC	TCC alarm
TCC+	TCC+ alarm
VT1	VT alarm

11.13.29 MODIFIER

Modifier for certain TL1 commands that are generic in their syntax

Table 11-48 MODIFIER Values
MODIFIER Values	Description
BITS	BITS command modifier
EQPT	Equipment command modifier
OC-12	OC-12 command modifier
OC-3	OC-3 command modifier
OC-48	OC-48 command modifier
STS-1	STS-1 command modifier
STS-12C	STS-12c command modifier
STS-3C	STS-3c command modifier
SYNCN	Synchronization command modifier
T3	T3/DS-3 command modifier

11.13.30 NOTIF_CODE

The 2-character Notification Code associated with an autonomous message

Table 11-49 NOTIF_CODE Values
NOTIF_CODE Values	Description
CL	The condition causing the alarm has Cleared
CR	A Critical alarm
MJ	A Major alarm
MN	A Minor alarm
NA	The condition is Not Alarmed
NR	The alarm is not reported

11.13.31 OCN_MONTYPE

OCN monitor type

Table 11-50 OCN_MONTYPE Values
OCN_MONTYPE Values	Description
CVL	Coding Violation - Line
ESL	Errored Second - Line
PJNEG	PPJC-PDET:Negative Pointer Justification
PJPOS	PPJC-PGEN:Negative Pointer Justification
PSC	Protection Switching Count
PSD	Protection Switching Duration
SEFS	Severely Errored Framing Seconds
UASL	Unavailable Second - Line

11.13.32 OCN_TYPE

Modifier used to differentiate the various levels of OC-N in the ENT/ED/DLT commands

Table 11-51 OCN_TYPE Values
OCN_TYPE Values	Description
OC-12	Optical Carrier level-12 (622Mbs)
OC-3	Optical Carrier level-3 (155Mbs)
OC-48	Optical Carrier level-48 (2.4Gbs)

11.13.33 ON_OFF

Disable or Enable Mode

Table 11-52 ON_OFF Values
ON_OFF Values	Description
OFF	Mode is disabled
ON	Mode is enabled

11.13.34 OPTICAL_MODE

Table 11-53 OPTICAL_MODE Values
OPTICAL_MODE Values	Description
SDH	The SDH optical mode the European format
SONET	The SONET optical mode the American format

11.13.35 PRIVILEGE

Security level

Table 11-54 PRIVILEGE Values
PRIVILEGE Values	Description
MAINT	Maintenance Security Level
PROV	Provision Security Level
RTRV	Retrieve Security Level
SUPER	Superuser Security Level

11.13.36 PROT_MOD_OP

Protection switch operation mode

Table 11-55 PROT_MOD_OP Values
PROT_MOD_OP Values	Description
FRCD	Force switch operation mode
MAN	Manual switch operation mode

11.13.37 PROTECTION_GROUP

Table 11-56 PROTECTION_GROUP Values
PROTECTION_GROUP Values	Description
1-1	1 to 1 protection group
1-N	1 to N protection group

11.13.38 PST

Primary State of the entity (e.g. facility)

Table 11-57 PST Values
PST Values	Description
IS	In-service
OOS	Out-of-Service

11.13.39 REVERTIVE_TIME

Table 11-58 REVERTIVE_TIME Values
REVERTIVE_TIME Values	Description
0.0 - 12.0	Revertive time is 0.0 to 12.0 minutes

11.13.40 REVERTIVE_TYPE

Table 11-59 REVERTIVE_TYPE Values
REVERTIVE_TYPE Values	Description
NR	Revertive type is disabled
R	Revertive type is enabled

11.13.41 RNG_TYPE

Defines the type of ring that is to be deployed for this path

Table 11-60 RNG_TYPE Values
RNG_TYPE Values	Description
BLSR2	2-Fiber Bidirectional Line Switched Ring
BLSR4	4-Fiber Bidirectional Line Switched Ring
UPSR	Unidirectional Path Switched Ring

11.13.42 SD_BER

The threshold for declaring Signal Degrade on a facility or path

Table 11-61 SD_BER Values
SD_BER Values	Description
1E-5 - 1E-9	SDBER is the 1E-5 to 1E-9

11.13.43 SDCC_MODE

Enables or disables the Section Data Communications Channel (SDCC) for the specified facility

Table 11-62 SDCC_MODE Values
SDCC_MODE Values	Description
N	Section Data Communications Channel is disabled for this facility
Y	Section Data Communications Channel is enabled for this facility

11.13.44 SERV_EFF

Indicates the effect of the alarm on service

Table 11-63 SERV_EFF Values
SERV_EFF Values	Description
NSA	The condition is Non-Service Affecting
SA	The condition is Service Affecting

11.13.45 SF_BER

The threshold for declaring Signal Failure on a facility or path

Table 11-64 SF_BER Values
SF_BER Values	Description
1E-3 - 1E-5	SFBER is the 1E-3 to 1E-5

11.13.46 SIDE

The role the unit is playing in the protection group

Table 11-65 SIDE Values
SIDE Values	Description
PROT	The entity is the protection unit in the protection group
WORK	The entity is a working unit in the protection group

11.13.47 STATE

The provisioned state of the equipment unit or facility

Table 11-66 STATE Values
STATE Values	Description
IS	The entity is InService
OOS-AS	The entity is Out-Of-Service and Assigned
OOS-UAS	The entity is Out-Of-Service and UnAssigned

11.13.48 STATUS

Indicates whether the unit in the pair is Active or Standby

Table 11-67 Status Values
STATUS Values	Description
ACT	The entity is the Active unit in the protection group
NA	Status is unavailable
STBY	The entity is the standby unit in the protection group

11.13.49 STM_TYPE

The Synchronous Transport Mode of the NE

Table 11-68 STM_TYPE Values
STM_TYPE Values	Description
SDH	The NE is operating in Synchronous Digital Hierarchy mode
SONET	The NE is operating in Synchronous Optical NETwork mode

11.13.50 STS_MONTYPE

Table 11-69 STS_MONOTYPE Values
STS_MONTYPE Values	Description
CVP	Coding Violation - P
ESP	Errored Second - Path
SESP	Severely Errored Second - Path
UASP	Unavailable Second - Path

11.13.51 STS_PATH

Modifier for some of the STS commands

Table 11-70 STS_PATH Values
STS_PATH Values	Description
STS-1	Synchronous Transport Signal level-1 (51Mbs)
STS-12C	Synchronous Transport Signal level-12 Concatenated (622Mbs)
STS-3C	Synchronous Transport Signal level-3 Concatenated (155Mbs)

11.13.52 SWITCH

The type of switch to be initiated

Table 11-71 SWITCH Values
SWITCH Values	Description
FRCD	Force a switch unless another FRCD or LOCKOUT is in effect
LOCKOUT	Locks the facility out of switching. The system cannot switch to the protect facility to carry service
MAN	Requests a manual switch of the facility

11.13.53 SYNC_GENERATION

Synchronization status message set generation

Table 11-72 SYNC_GENERATION Values
SYNC_GENERATION Values	Description
GEN1	First generation SSM set
GEN2	Second generation SSM set

11.13.54 SYNC_MODE

Table 11-73 SYNC_MODE Values
SYNC_MODE Values	Description
FRNG	Reset operation mode
FST	Reset operation mode
HLDOVR	Reset operation mode
NORM	Reset operation mode

11.13.55 SYNC_QUALITY_LEVEL

Reserved for network synchronization quality level

Table 11-74 SYNC_QUALITY_LEVEL Values
SYNC_QUALITY_LEVEL Values	Description
ABOVE-PRS	Better than Primary Reference Source
ABOVE-SMC	Between SMC and ST3
ABOVE-ST2	Between ST2 and STU
ABOVE-ST3	Between ST3 and ST2
ABOVE-ST3E	Between ST3E and TNC
ABOVE-ST4	Between ST4 and ST3
ABOVE-STU	Between STU and PRS
ABOVE-TNC	Between TNC and PRS
BELOW-ST4	Below ST4 but still usable
SAME-AS-DUS	Disable the RES message by equating it to DUS

11.13.56 TIMING_MODE

Timing mode for the current node

Table 11-75 TIMING_MODE Values
TIMING_MODE Values	Description
EXTERNAL	The node derives its clock from the BITS input
LINE	The node derives its clock from the SONET lines

11.13.57 TMG_REF

Identifies whether or not this entity is the Timing Reference for its group. For equipment, it identifies the facility that is supplying the timing reference. For interface groups, it identifies the card that is supplying the main timing reference.

Table 11-76 TMG_REF Values
TMG_REF Values	Description
N	This facility or card is not a timing reference
Y	This facility or card is a timing reference

11.13.58 TMPR

Performance parameter

Table 11-77 TMPR Values
TMPR Values	Description
15MIN	Performance Parameter Accumulation Interval Length - Every 15 Minutes
1DAY	Performance Parameter Accumulation Interval Length - Every 24 Hours

11.13.59 USE_DST

Identifies whether Daylight Saving Time is recognized in the area where this NE is deployed

Table 11-78 USE_DST Values
USE_DST Values	Description
N	Daylight Saving Time is not recognized
Y	Daylight Saving Time is recognized

11.13.60 VALIDITY

Response validity

Table 11-79 VALIDITY Values
VALIDITY Values	Description
COMPL	Complete Response
PRTL	Partial Response

11.13.61 Performance Monitoring Parameters by Line Type

Table 11-80 Performance Monitoring Parameters by Line Type
	OC-n	T1	T3	STS	VT1.5
CVL	Y	Y	Y
CVP		Y	Y	Y
CVS	Y
CVV					Y
ESL	Y	Y	Y
ESP		Y	Y	Y
ESS	Y
ESV					Y
FCP				Y
FCL	Y
PJNEG	Y
PJPOS	Y
PSC	Y
PSD	Y
SASP		Y	Y
SEFS	Y
SESL	Y	Y	Y
SESP		Y	Y	Y
SESS	Y
SESV					Y
UASL	Y
UASP		Y	Y	Y
UASV					Y
AISSP		Y	Y
CVCPP			Y
ESCPP			Y
LOSSL			Y
SASCPP			Y
SESCPP			Y
UASCPP			Y

11.14 Errors

Errors may be generated by any command or command response message. The format of an error message is as follows:

sid date time
M ctag DENY
<errcde>
/* <errmsg> */
;

Table 11-81 Error Codes
Error Code (errcde)	Error Type	Error Message (errmsg)
EANS	EQUIPAGE	Access Not Supported
EATN	EQUIPAGE	Not Valid for Access Type
EFON	EQUIPAGE	Feature Option Not Provided
EN2T	EQUIPAGE	Not 2-Wire Terminate and Leave
ENAC	EQUIPAGE	Not Equipped with Alarm Cutoff
ENAD	EQUIPAGE	Not Equipped with Audit Capability
ENAR	EQUIPAGE	Not Equipped with Automatic Reconfiguration
ENAT	EQUIPAGE	Request Not Valid for Access Type
ENDG	EQUIPAGE	Not Equipped with Diagnostic Capability
ENDS	EQUIPAGE	Not Equipped with Duplex Switching
ENEA	EQUIPAGE	Not Equipped with Error Analysis Capability
ENEQ	EQUIPAGE	Not Equipped
ENEX	EQUIPAGE	Not Equipped with Exercise Capability
ENFE	EQUIPAGE	Feature Not Provided
ENFL	EQUIPAGE	Not Equipped for Fault Locating
ENHN	EQUIPAGE	Not Hybrid Network
ENMB	EQUIPAGE	Not Multipoint Bridge
ENMD	EQUIPAGE	Not Equipped with Memory Device
ENPM	EQUIPAGE	Not Equipped for Performance Monitoring
ENPS	EQUIPAGE	Not Equipped with Protection Switching
ENRE	EQUIPAGE	Not Recognized Equipage
ENRI	EQUIPAGE	Not Equipped for Retrieving Specified Information
ENRS	EQUIPAGE	Not Equipped for Restoration
ENSA	EQUIPAGE	Not Equipped for Scheduling Audit
ENSG	EQUIPAGE	Not Software Generic
ENSI	EQUIPAGE	Not Equipped for Setting Specified Information
ENSS	EQUIPAGE	Not Equipped with Synchronization Switching
ENTL	EQUIPAGE	Not Terminate and Leave
ERLC	EQUIPAGE	Red-Lined Circuit
ERNS	EQUIPAGE	RTU Does Not Support Command
ESPG	EQUIPAGE	Software Program
ETNS	EQUIPAGE	TSC Does Not Support Command
FNCR	FAULT	NE Failure - Circuit Restored to Last Condition - Monitor or Terminate
FNDT	FAULT	No Dial Tone Detected
FNEC	FAULT	NTE Has Lost 8-KHZ Byte Clock
FNSC	FAULT	NTE Has Lost 16-KHZ Byte Clock
FRCE	FAULT	RTU Component or Configuration Error
FRDA	FAULT	RTU Does Not Answer the Call
FREC	FAULT	RTU Eight KHZ Byte Clock Lost
FRNR	FAULT	RTU Does Not Reply
IBEX	INPUT	Block Extra
IBMS	INPUT	Block Missing
IBNC	INPUT	Block Not Consistent
ICNV	INPUT	Command Not Valid
IDMS	INPUT	Data Missing
IDNC	INPUT	Data Not Consistent
IDNV	INPUT	Data Not Valid
IDRG	INPUT	Data Range Error
IIAC	INPUT	Invalid Access Identifier (AID)
IICM	INPUT	Invalid Command
IICT	INPUT	Invalid Correlation Tag
IIDT	INPUT	Invalid Data Parameter
IIFM	INPUT	Invalid Data Format
IIPG	INPUT	Invalid Parameter Grouping
IISP	INPUT	Invalid Syntax or Punctuation
IITA	INPUT	Invalid Target Identifier
INAC	INPUT	Access Number Not Correct
INUP	INPUT	Non-Null Unimplemented Parameter
IPEX	INPUT	Parameter Extra
IPMS	INPUT	Parameter Missing
IPNC	INPUT	Parameter Not Consistent
IPNV	INPUT	Parameter Not Valid
ISCH	INPUT	Syntax Invalid Character
ISPC	INPUT	Syntax Punctuation
ITSN	INPUT	Invalid/Inactive Test Session Number
PICC	PRIVILEGE	Illegal Command Code
PIMA	PRIVILEGE	Invalid Memory Address
PIMF	PRIVILEGE	Invalid Memory File
PIUC	PRIVILEGE	Illegal Privilege Code
PLNA	PRIVILEGE	Login Not Active
RABY	RESOURCE	All Taps Busy
RALB	RESOURCE	All Units of Requested Type are Busy
RANB	RESOURCE	Access Network Busy
RCBY	RESOURCE	Circuit Busy
RCIN	RESOURCE	Requested Circuit ID Does Not Exist
RNAN	RESOURCE	Requested NE Access Number Does Not Exist
RNAU	RESOURCE	Requested NE Access Number Unassigned
RNBY	RESOURCE	NE is Busy
RRCP	RESOURCE	Unit Specified by Routing Code Busy
RRNG	RESOURCE	Requested Changes Exceeds Range
RTBY	RESOURCE	Requested Tap Busy
RTEN	RESOURCE	Requested Tab Does Not Exist
RTUB	RESOURCE	Test Unit Busy
SAAL	STATUS	Already Allowed
SAAS	STATUS	Already Assigned
SABT	STATUS	Aborted
SACS	STATUS	Access Unit Cannot Sync on Facility Signal
SADC	STATUS	Already Disconnected
SADS	STATUS	Access Unit in Diagnostic State
SAIN	STATUS	Already Inhibited
SAIS	STATUS	Already In-Service
SAMS	STATUS	Already in Maintenance State
SAOP	STATUS	Already Operated
SAOS	STATUS	Already Out-of-Service
SAPF	STATUS	Access Path Continuity Check Failed
SAPR	STATUS	Already in Protection State
SARB	STATUS	All Resources Busy
SATF	STATUS	Automatic Test Failed
SCAT	STATUS	Circuit is Already Connected to Another Tap
SCBS	STATUS	Channel Busy
SCIS	STATUS	Circuit in Split Condition
SCNA	STATUS	Command Not Able to be Aborted
SCNF	STATUS	Command Not Found
SCNS	STATUS	Circuit Not in Split Condition
SCOS	STATUS	Channel Out-of-Service
SCSD	STATUS	Can't Split DS0B Circuit
SCSN	STATUS	Invalid Command Sequence
SDAS	STATUS	Diagnosis Already Started
SDBE	STATUS	Internal Data Base Error
SDFA	STATUS	Duplex Unit Failed
SDLD	STATUS	Duplex Unit Locked
SDNA	STATUS	Dumple Unit Not Available
SDNC	STATUS	Input Data is Not Consistent With NE Data
SDNR	STATUS	Data Not Ready
SDNS	STATUS	Diagnosis Not Started Yet
SEOS	STATUS	NTE is Out-of-Service
SFAS	STATUS	Fault Locating Already Started
SFNS	STATUS	Fault Locating Not Started yet
SFYA	STATUS	Facility Reports Yellow Alarm
SLNS	STATUS	Log Not Started Yet
SLOS	STATUS	TSC to RTU Link Out-of-Service
SNCC	STATUS	Not Cross-Connected
SNCN	STATUS	NTE Unable to Execute Command
SNDS	STATUS	NTE is in a Diagnostic State
SNIM	STATUS	NTE Access Complete, Circuit was in Monitor State
SNIS	STATUS	Not in Service
SNML	STATUS	No Monitor Line Established
SNNB	STATUS	NTE Could Not Sync on DS0B Signal
SNNS	STATUS	NTE Could Not Sync on DS-1 Signal
SNOS	STATUS	NTE is Out-of-Service
SNPR	STATUS	Not in Protection State
SNRM	STATUS	System Not in Restoration Mode
SNRS	STATUS	Not Reserved
SNSR	STATUS	No Switch Request Outstanding
SNVS	STATUS	Not in Valid State
SNYA	STATUS	NTE has Detected a Yellow Alarm
SOSE	STATUS	Operating System Error
SOST	STATUS	Out-of-Service, Testing
SPFA	STATUS	Protection Unit Failed
SPLD	STATUS	Protection Unit Locked
SPNA	STATUS	Process Not Able to be Aborted
SPNF	STATUS	Process Not Found
SRAC	STATUS	Requested Access Configuration is Invalid
SRAN	STATUS	Unable to Release Access System
SRCI	STATUS	Requested Command(s) Inhibited
SRCN	STATUS	Requested Condition Already Exists
SROF	STATUS	Requested Operation Failed
SROS	STATUS	Required RTU Out of Service
SRQN	STATUS	Invalid Request
SRTN	STATUS	Unable to Release Tap
SRTO	STATUS	Reply Timeout Occurred
SSCE	STATUS	Systemic (SNIDER) Communications Error
SSNG	STATUS	Subrate Selected is Incorrect
SSNP	STATUS	Speed Selected is Incorrect
SSNQ	STATUS	Test Signal Not QRS
SSRD	STATUS	Switch Request Denied
SSRE	STATUS	System Resources Exceeded
STAB	STATUS	Test Aborted
STLC	STATUS	Tap Unable to Locate Channel
STNO	STATUS	TSC/RTU to TAU Link Out of service
STOS	STATUS	Test Access Unit Out of Service
STTI	STATUS	Tap Idle
SWFA	STATUS	Working Unit Failed
SWLD	STATUS	Working Unit Locked

11.15 Echo

In order to improve telnet functionality for automated systems, the echo function was been turned off in Release 2.1.0. This change is transparent to users running standard UNIX-compliant telnet clients; however, PC users may need to change their client setup to enable "local echo." This is normally accomplished by a pull-down menu or a preference attribute.

To test the local echo on your PC client, use the RTRV-HDR command. If you receive a response but no data, set local echo ON.

Command	Superuser	Provision	Maintenance	Retrieve
DLT-USER-SECU	X
ED-DAT	X
ED-USER-SECU	X
ENT-USER-SECU	X
SET-TOD	X	X
DLT--	X	X
ED--	X	X
ENT--	X	X
SET--	X	X
INIT--	X	X	X
OPR--	X	X	X
RLS--	X	X	X
RMV--	X	X	X
RST--	X	X	X
SW--	X	X	X
ALW--	X	X	X	X
INH--	X	X	X	X
REPT * *	X	X	X	X
RTRV--	X	X	X	X
CANC--	X	X	X	X
ACT--	X	X	X	X
ED-PD	X	X	X	X

Table Of Contents

11

TL1 Reference