|
Table Of Contents
Release Notes for Cisco ONS 15530
for Cisco IOS Release 12.2(18)SV1Determining the Software Version
New Features in Release 12.2(18)SV1
New Features in Release 12.2(18)SV
Open Caveats in Release 12.2(18)SV1
Resolved Caveats in Release 12.2(18)SV1
Resolved Caveats in Release 12.2(18)SV
Obtaining Technical Assistance
Obtaining Additional Publications and Information
Release Notes for Cisco ONS 15530
for Cisco IOS Release 12.2(18)SV1
This document describes caveats for Cisco IOS Release 12.2(18)SV1 for the Cisco ONS 15530.
Date: November 24, 2003
Text Part Number: OL-4891-02
Contents
This document includes the following information:
• Caveats
• Limitations and Restrictions
• Obtaining Technical Assistance
• Obtaining Additional Publications and Information
Introduction
The Cisco ONS 15530 is a DWDM multiservice aggregation platform that maximizes the carrying capacity of fiber by performing service aggregation of protocols such as ESCON, Fibre Channel, FICON, and Gigabit Ethernet. With the Cisco ONS 15530, users can take advantage of the availability of dark fiber to build a common infrastructure that supports data, SAN (storage area networking), and TDM (time-division multiplexing) traffic. For more information about DWDM technology and applications, refer to the Introduction to DWDM Technology publication and the Cisco ONS 15530 Planning Guide.
System Requirements
This section describes the system requirements for Cisco IOS Release 12.2(18)SV and includes the following sections:
• Determining the Software Version
Memory Requirements
The DRAM memory configuration is 64 MB, which is the default for the Cisco ONS 15530.
Hardware Supported
Table 1 lists the hardware components supported on the Cisco ONS 15530 and the minimum software version required. See the "Determining the Software Version" section.
Determining the Software Version
Note We strongly recommend that you use the latest available software release for all Cisco ONS 15530 hardware.
To determine the version of Cisco IOS software currently running on a Cisco ONS 15530 system, log in to the system and enter the show version EXEC command. The following sample output is from the show version command. The software version number is shown on the second line of the sample output.
Switch# show version
Cisco Internetwork Operating System Software
IOS (tm) ONS-15530 Software (ONS15530-I-M), Version 12.2(18)SV1
<Information deleted>Upgrading the System Image
To ensure proper system functioning, follow the system image upgrading procedure described in the Cisco ONS 15530 Software Upgrade Guide.
You can find the system images for the Cisco ONS 15530 at the following URL:
http://www.cisco.com/kobayashi/sw-center/sw-optical.shtml
Note Always set the configuration register to 0x2102 when upgrading the system image using the config-reg 0x2102 command in configuration mode.
Caution Improper system image upgrades can affect system functioning and redundancy. Always follow the recommended upgrade procedures.
Feature Set Table
The Cisco IOS Release software is packaged in feature sets (also called software images) depending on the platform. Each feature set contains a specific set of Cisco IOS features. Table 2 lists the Cisco IOS software feature sets available for the Cisco ONS 15530.
Table 2 Feature Sets Supported by the Cisco ONS 15530
Feature Set Introduced in This ReleaseInband message channel
12.1(10)EV2
Gigabit Ethernet
12.1(10)EV2
Fast Ethernet
12.1(10)EV2
Ethernet
12.1(10)EV2
ATM OC-3/STM-1, OC-12/STM-4, and OC-48/STM-16
12.1(10)EV2
12.1(10)EV2
POS3
12.1(10)EV2
IBM Sysplex coupling link
12.1(10)EV2
Fibre Channel (1 Gbps)
12.1(10)EV2
Fibre Channel (2 Gbps)
12.1(10)EV2
FDDI4
12.1(10)EV2
ESCON5 aggregation (2.5 Gbps)
12.1(10)EV2
FICON6 (800 Mbps)
12.1(10)EV2
FICON (1 Gbps)
12.1(12c)EV3
Token ring
12.1(10)EV2
SNMP
12.1(10)EV2
CiscoView
12.1(10)EV2
Cisco Transport Manager
12.1(10)EV2
IP packets
12.1(10)EV2
OSCP7
12.1(10)EV2
APS8 channel protocol
12.1(10)EV2
Point-to-point
12.1(10)EV2
Hubbed ring
12.1(10)EV2
Meshed ring
12.1(10)EV2
IBM Sysplex ETR/CLO9
12.1(10)EV2
1 Gbps Fibre Channel/FICON aggregation into 2.5 Gbps
12.1(12c)EV
1 Gbps IBM Sysplex Coupling Link aggregation into 2.5 Gbps
12.2(18)SV
Gigabit Ethernet aggregation (2.5 Gbps)
12.1(12c)EV
Buffer credits for 8-port FC/GE aggregation card
12.2(18)SV
2-Gbps Fibre Channel protocol monitoring on transparent transponder
12.2(18)SV
2-Gbps FICON protocol monitoring
12.2(18)SV
Functional image version diagnostics
12.2(18)SV
Autonegotiation for Gigabit Ethernet between the 8-port FC/GE aggregation card and the client equipment
12.2(18)SV
ISC links compatibility mode aggregation (2.5 Gbps)
12.2(18)SV
1 SONET = Synchronous Optical Networking
2 SDH = Synchronous Digital Hierarchy
3 POS = Packet over SONET
4 FDDI = Fiber Distributed Data Interface
5 ESCON = Enterprise Systems Connection
6 FICON = Fiber Connection
7 OSCP = Optical Supervisory Channel Protocol
8 APS = Automatic Protection Switching
9 ETR/CLO = external timer reference/control link oscillator
New and Changed Information
This section lists new features that appear in this and previous releases of Cisco IOS Release 12.2. The new features are sorted by release number.
New Features in Release 12.2(18)SV1
No new features are available for this release.
New Features in Release 12.2(18)SV
The following new software features are available for the Cisco ONS 15530 in Cisco IOS Release 12.2(18)SV:
•Autonegotiation between the 8-port FC/GE aggregation card and the client equipment for Gigabit Ethernet traffic
Note The 8-port FC/GE aggregation card does not support end-to-end pass through of autonegotiation parameters in the current release.
•ISC links compatibility mode aggregation (2.5 Gbps)
•Buffer credits for Fibre Channel distance extension
•2-Gbps Fibre Channel protocol monitoring
Note 2-Gbps Fibre Channel protocol monitoring requires transponder functional image
release 1.A3.
•2-Gbps FICON protocol monitoring
•Data file with upgrade information for the ROMMON and functional images
•show upgrade-info functional-image command
•negotiation auto command
•flow control command
Caveats
This section describes open and resolved severity 1 and 2 caveats and some severity 3 caveats. The "Open Caveats" section lists open caveats that apply to the current release and may apply to previous releases. The "Resolved Caveats" sections list caveats resolved in a particular release, but open in previous releases.
Open Caveats in Release 12.2(18)SV1
•CSCdu53656
A Cisco device running IOS and enabled for the Border Gateway Protocol (BGP) is vulnerable to a Denial of Service (DOS) attack from a malformed BGP packet. The BGP protocol is not enabled by default, and must be configured in order to accept traffic from an explicitly defined peer. Unless the malicious traffic appears to be sourced from a configured, trusted peer, it would be difficult to inject a malformed packet. BGP MD5 is a valid workaround for this problem.
Cisco has made free software available to address this problem. For more details, please refer to this advisory, available at http://www.cisco.com/warp/public/707/cisco-sa-20040616-bgp.shtml.
•CSCdz59146
Symptom: The ethernetdcc interface loses connectivity when splitter protection is configured and the waveethernetphy interface is shut down while the protection wavepatch interface is active and the working wavepatch interface is down.
Workaround: Do not shut down the waveethernetphy interface while the working wavepatch interface is down.
•CSCea28131
A Cisco device running IOS and enabled for the Border Gateway Protocol (BGP) is vulnerable to a Denial of Service (DOS) attack from a malformed BGP packet. The BGP protocol is not enabled by default, and must be configured in order to accept traffic from an explicitly defined peer. Unless the malicious traffic appears to be sourced from a configured, trusted peer, it would be difficult to inject a malformed packet. BGP MD5 is a valid workaround for this problem.
Cisco has made free software available to address this problem. For more details, please refer to this advisory, available at http://www.cisco.com/warp/public/707/cisco-sa-20040616-bgp.shtml.
•CSCea52092
Symptom: After booting the system, power coming out of the OSC module seems to be null even though the laser is enabled.
Workaround: Perform an online removal and insertion of the OSC module or carrier motherboard.
•CSCeb18103
Symptom: The OSC wave interface does not come back up after resolving a trunk fibre break if laser safety control was configured after the trunk fiber break occurred.
Workaround: Disable and then enable LSC again to bring up the OSC wave interface.
•CSCec14447
Symptom: The 8-port GE/FC aggregation card laser is not in the proper state when a Tx-CRC threshold has been exceeded and FLC is configured.
Workaround: Issue the shutdown/no shutdown command sequence on the affected interface.
•CSCec42573
Symptom: In a y-cable APS configuration interfaces on the 8-port GE/FC aggregation card configured for FICON encapsulation change to GE encapsulation when the saved configuration file is copied to the running configuration.
Workaround: Change the encapsulation back to FICON.
•CSCin78329
Symptom: Power-on diagnostics may fail the credit-buffer-memory test for the 8-port FC/GE aggregation card on the first boot after power cycling the box. Subsequent reboots without power cycling pass the test. These test failures are spurious and can be ignored.
Workaround: Upgrade you Cisco ONS 15530 software to Cisco IOS Release 12.2(23)SV or later.
Resolved Caveats in Release 12.2(18)SV1
•CSCdz64021
Symptom: While performing an online removal and insertion of a protection card in a y-cable configuration, the local and remote working ports are flooded with CRC errors.
Workaround: Disconnect the standby branch of the y-cable configuration during the insertion of the standby line card or SFP optics.
•CSCec28182
Symptom: Tracebacks related to CPU hog issues are seen when reprogramming the 2.5-Gbps transponder line card functional image.
Workaround: None.
•CSCec36614
Symptom: Performing an online removal and insertion on a tengigethernetphy interface or waveethernetphy interface when loopback is configured causes a loss of the loopback information on the hardware. However, the loopback CLI configuration is still present in the software.
Workaround: Remove and reinsert the line card, and then issue the loopback command.
•CSCec59409
Symptom: Issuing a Ctrl-U when connected to a raw TL1 port causes the system to crash.
Workaround: If a TL1port is unused, apply an IP ACL to the management Ethernet interface that blocks the incoming TCP connections to ports 3082 and 3083.
•CSCec88050
Symptom: Power-on diagnostics fail on the CPU switch module if a 2.5-ITU trunk card is installed in slot 1.
Workaround: None.
Resolved Caveats in Release 12.2(18)SV
•CSCdz89270
Symptom: OFC (open fibre control) is not supported with Fibre Channel on the 8-port FC/GE aggregation card. The link might not initialize if an 8-port FC/GE aggregation card is used with older Fibre Channel equipment that employ OFC laser safety mechanisms.
Workaround: None.
•CSCeb19410
Symptom: An 8-port FC/GE aggregation card client interface laser may be off when it is configured in a disabled y-cable APS group.
Workaround: Enable and then disable the APS group. This activates the client interface laser.
•CSCec03715
Symptom: If the flow identifier on an esconphy interface is changed without deleting the old flow identifier, both the old and the new flow identifiers are present in the lookup table of the ESCON aggregation card. As a result, the old flow identifier cannot be reused on this ESCON aggregation card.
Workaround: Perform an online removal and insertion of the ESCON aggregation card or issue the following sequence of commands in interface configuration mode:
1. no cdl flow identifier
2. cdl flow identifier [OLD IDENTIFIER]
3. no cdl flow identifier
4. cdl flow identifier [NEW IDENTIFIER]
•CSCec34628
Symptom: Continuous optical power monitoring alarms cause memory leaks that lead to bus error exceptions and an unexpected reload.
Workaround: None.
Limitations and Restrictions
This section provides limitations and restrictions for Cisco ONS 15530 hardware and software.
Transponder Line Cards
This section contains limitations and restrictions that apply to transponder line cards.
•CRC errors might occur with 2-Gbps Fibre Channel on single-mode transponders when high input power levels are received from the client laser sources.
Data errors or link-down conditions for 2-Gbps Fibre Channel might occur when used with certain client laser sources. Transmitters in some client GBIC and SFP transceiver units might send large overshoots in optical power with signal bit transitions, causing momentary overload conditions on the transponder client side receiver. The average transmitted power level from the GBIC does not violate the overload specification of the transponder client side receiver, so a power meter does not detect the overload.
The workaround is to attenuate the signal from the client equipment to a recommended level of -12 dBm when transmitting 2-Gbps Fibre Channel services.
•Error-free transmission of some D1 video signals (defined by the SMPTE 259M standard) and test patterns (such as Matrix SDI) cannot be guaranteed by the Cisco 15500 Series because of the pathological pattern in D1 video. This well-known limitation is usually overcome by the D1 video equipment vendor, who uses a proprietary, second level of scrambling. No standards exist at this time for the second level of scrambling.
CPU Switch Modules
This section contains limitations and restrictions that apply to transponder modules.
•If both CPU switch modules are removed, all aggregation cards, OSC modules, transponder line cards, ITU trunk cards, and uplink cards are shut down.
Note Traffic on pass through optical channels (which passively pass through the OADM modules) are not affected by the removal of the processor cards.
Related Documentation
Refer to the following documents for more information about the Cisco ONS 15530:
• Regulatory Compliance and Safety Information for the Cisco ONS 15500 Series
• Cisco ONS 15530 Planning Guide
• Cisco ONS 15530 Hardware Installation Guide
•Cisco ONS 15530 Optical Transport Turn-Up and Test Guide
• Cisco ONS 15530 Cleaning Procedures for Fiber Optic Connections
• Cisco ONS 15530 Configuration Guide
• Cisco ONS 15530 Command Reference
• Cisco ONS 15530 System Alarms and Error Messages
• Cisco ONS 15530 Troubleshooting Guide
• Network Management for the Cisco ONS 15530
• Cisco ONS 15530 TL1 Commands
•MIB Quick Reference for the Cisco ONS 15500 Series
•Cisco ONS 15530 Software Upgrade Guide
Obtaining Documentation
Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation on the World Wide Web at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
International Cisco websites can be accessed from this URL:
http://www.cisco.com/public/countries_languages.shtml
Documentation CD-ROM
Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated regularly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual or quarterly subscription.
Registered Cisco.com users can order a single Documentation CD-ROM (product number DOC-CONDOCCD=) through the Cisco Ordering tool:
http://www.cisco.com/en/US/partner/ordering/ordering_place_order_ordering_tool_launch.html
All users can order annual or quarterly subscriptions through the online Subscription Store:
http://www.cisco.com/go/subscription
Click Subscriptions & Promotional Materials in the left navigation bar.
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).
Documentation Feedback
You can submit e-mail comments about technical documentation to bug-doc@cisco.com.
You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services, online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.
Cisco TAC Website
The Cisco TAC website ( http://www.cisco.com/tac) provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365 days a year.
Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a login ID or password, register at this URL:
http://tools.cisco.com/RPF/register/register.do
Opening a TAC Case
Using the online TAC Case Open Tool ( http://www.cisco.com/tac/caseopen) is the fastest way to open P3 and P4 cases. (P3 and P4 cases are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Case Open Tool automatically recommends resources for an immediate solution. If your issue is not resolved using the recommended resources, your case will be assigned to a Cisco TAC engineer.
For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.
To open a case by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447For a complete listing of Cisco TAC contacts, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
TAC Case Priority Definitions
To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.
Priority 1 (P1)—Your network is "down" or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Priority 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.
Priority 3 (P3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.
Priority 4 (P4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online and printed sources.
•The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://www.cisco.com/en/US/products/products_catalog_links_launch.html
•Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press online at this URL:
•Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources. You can access Packet magazine at this URL:
•iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet business strategies for executives. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_protocol_journal.html
•Training—Cisco offers world-class networking training. Current offerings in network training are listed at this URL:
http://www.cisco.com/en/US/learning/index.html
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, MGX, MICA, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, Stratm, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0304R)
Copyright © 2003 Cisco Systems, Inc. All rights reserved.
Posted: Sat Jul 31 12:37:09 PDT 2004
All contents are Copyright © 1992--2004 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.