Table of Contents

Obtaining Service
Summary of the Hardware Troubleshooting Process
Understanding the LEDs

Switch LEDs
Port LEDs
Stack Port Module LEDs
Fiber and UTP/STP Module LEDs
ATM Module LEDs
ISL Module LEDs

Choosing a Troubleshooting Procedure

Procedure A
Procedure B
Procedure C
Procedure D

Hardware Troubleshooting

This appendix contains procedures that help you troubleshoot physical problems with a Catalyst 3900 Token Ring Switch and its connections to other devices.

• Obtaining Service

• Summary of the Hardware Troubleshooting Process

• Understanding the LEDs

• Choosing a Troubleshooting Procedure

Caution There are no operator-serviceable parts in the Catalyst 3900. Refer servicing to qualified personnel.

Obtaining Service

There are no serviceable parts inside the Catalyst 3900. Do not remove the cover for any reason. The Catalyst 3900 and each feature card are individually replaceable.

Summary of the Hardware Troubleshooting Process

If one or more devices (such as a computer) connected to a Catalyst 3900 are unable to communicate with other devices in the network, use the following steps to start the troubleshooting process:

Step 1 Using the network sketch, the label on the cable connected to the device, or other network records, locate the Catalyst 3900 to which the device is connected.

Step 2 If all troubled devices connect to a single feature card, use the feature card documentation to assist in troubleshooting.

Step 3 If you have set up a console session (described in the "Planning for Configuration and Management" chapter), it can be used to determine whether diagnostics have been completed correctly. Refer to the "Resetting the Catalyst 3900" chapter for more information.

Step 4 Observe the LEDs on the Catalyst 3900 front panel. Review the "Understanding the LEDs" section before proceeding with the troubleshooting process.

Step 5 Select a troubleshooting procedure as described in the "Choosing a Troubleshooting Procedure" section.

Understanding the LEDs

This section describes the meanings of the various states of the LEDs that are on the Catalyst 3900 and its expansion modules.

Switch LEDs

Table C-1 lists the Catalyst 3900 status LEDs and their meanings.

Port LEDs

Table C-2 lists the port LEDs and their meanings.

Stack Port Module LEDs

Table C-3 lists the stack LEDs and their meanings.

Fiber and UTP/STP Module LEDs

There are status LEDs on the front of the 4-port fiber and the 4-port UTP/STP Token Ring modules that indicate the operational status of the ports and the module.

Table C-4 lists the LEDs for the module and their meanings.

Table C-5 lists the LEDs for the ports and their meanings.

ATM Module LEDs

Table C-6 describes the ATM module status LEDs and their meanings.

Table C-7 describes the ATM port status LEDs and their meanings.

ISL Module LEDs

There is one status LED for the ISL module. It is the DIAG LED. The DIAG LED is lit during power-up diagnostics. If one of the ports on the module fails the diagnostic tests, the DIAG LED will remain lit. Otherwise, it is off.

There are three status LEDs for each of the ports. Table C-8 lists the port LEDs and their meanings.

Choosing a Troubleshooting Procedure

Use Table C-9 to determine which troubleshooting procedure you should use.

Procedure A

Use the following procedure if all LEDs are off:

Step 1 Verify that the power cord is connected at both ends and that the power outlet is working.

Step 2 If the power cord is connected correctly, the outlet is working, and the problem persists, the problem is in the Catalyst 3900. Contact the Cisco TAC.

Procedure B

Use the following procedure if the Fault LED (amber) is on:

Step 1 Reset the Catalyst 3900 by disconnecting the power cord. Wait 10 seconds and then reconnect the cord. If the problem goes away, resume using the Catalyst 3900.

Step 2 If you have just downloaded new software, clear NVRAM and reset the Catalyst 3900 using the instructions in the "Resetting the Catalyst 3900" chapter.

Step 3 Reset the Catalyst 3900 and monitor the diagnostic messages for individual port failures. Correct any individual port problems that are detected. If the failing ports are feature card ports, use the feature card documentation to try to correct the problem.

Step 4 If the problem persists, the problem is in the Catalyst 3900. Contact the Cisco TAC.

Procedure C

Use the following procedure if all devices connected to the Catalyst 3900 have communication problems, the Catalyst 3900 Fault LED is off, and the Mode LED is off:

Reset the Catalyst 3900 by disconnecting power cord for 10 seconds. Reconnect the power cord.

• If the problem is corrected, resume using the Catalyst 3900.

• If the box status LEDs indicate a failure, go to Procedure B.

• If the problem persists, check all the configuration parameters.

• If the problem continues, go to Procedure D to correct problems with the individual ports.

Procedure D

Use the following procedure if one device connected to the Catalyst 3900 is having a communication problem, the Catalyst 3900 Fault LED is off, Mode LED is off, and other attached devices can communicate through the Catalyst 3900:

Step 1 Check the port LEDs.

• If the port Connect LED is on, the problem is probably external to the Catalyst 3900. Go to Step 2.

• If the port Connect LED is off, the port is probably disabled. Check that the port configuration matches the attached device, and then go to Step 3.

• If the port Connect LED is blinking, go to Step 4.

Step 2 If the Connect LED on the failing port is on and the attached device still cannot communicate, do the following:

• If the attached device is directly connected, it might be set up incorrectly. Go to Step 4.

• In a shared environment, check the segment cabling and the media access unit. Got to Step 5.

• If problem persists, try another identically configured port on the Catalyst 3900. If the new port works, there is a problem with the failed port. Contact the Cisco TAC.

Step 3 Determine whether the port has been disabled:

Step 4 Restart the communications program on the failed connected device.

Step 5 If the Catalyst 3900 is connected to a Token Ring concentrator, perform the following steps:

Posted: Tue Oct 12 11:57:29 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.