cc/td/doc/product/dsl_prod/c6130ni2/userdoc
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Technical Specifications
 Hardware Specifications
 Software Specifications

Technical Specifications

This appendix provides the technical specifications for the Cisco 6130 with NI-2 system. The appendix contains the following sections:

Hardware Specifications

This section details the specifications for the following hardware components:

Cisco 6130 with NI-2 System Specifications

Table A-1 lists the hardware specifications of the Cisco 6130 with NI-2 system.

Table A-1   Hardware Specifications

Specification Description

Dimensions

Cisco 6130
Cisco 6120
Fan tray

9 RUs1—23 in. x 15.75 in. x 12 in. (58.42 cm x 40.005 cm x 30.48 cm)
4 RUs—23 in. x 7 in. x 12 in. (58.42 cm x 17.78 cm x 30.48 cm)
2 RUs—23 in. x 3.5 in. x 12 in. (58.42 cm x 8.89 cm x 30.48 cm)

Weight

Cisco 6130

Cisco 6120

Fan tray

Empty—approximately 31 lb (14.06 kg)
Loaded—approximately 62 lb (28.12 kg)
Empty—approximately 16 lb (7.26 kg)
Loaded—approximately 34 lb (15.42 kg)
Loaded—approximately 18.45 lb (8.37 kg)

Network interface

ATM OC-3c (single- or multimode fiber), ATM DS3

ADSL interface

CAP—Up to 7.168 Mbps downstream/1.088 Mbps upstream
DMT—Up to 8.032 Mbps downstream/1024 kbps upstream
G.lite—Up to 1.536 Mbps downstream/512 kbps upstream

SDSL interface

2B1Q encoding; up to 1168 kbps upstream and downstream

Craft interface

Console terminal connection on the NI-2 card

Management access

  • RJ-45 interface for craft alarm discovery
  • RJ-45 Ethernet
  • ATM in-band management

External alarm contacts

Single dry contact alarm input (NO)

Power requirements

-48V DC

Note See "Preparing for Installation" for detailed power requirements.

CO operating requirements

Temperature

Altitude
Humidity

41 to 104ºF (5 to 40ºC)—Operating
23 to 163ºF (-5 to 50ºC)—Short term operating
-60 meters to 3200 meters
5 to 90% (noncondensing)

Subtending

NI-2 card

Redundancy

NI-2 card and APS2

1RU = rack unit. An RU is equal to 1.75 inches (4.45 cm).

2APS = automatic protection switching.

4xDMT Specifications

Table A-3 lists the specifications for the 4xDMT.

Table A-2   4xDMT Specifications

Specification Description

Standards supported

ITU G.dmt
ITU G.lite
ANSI T1.413 Issue 2

External interfaces

4 (no connectors on card)

Data rates (per port)

Upstream: Up to 864 kbps
Downstream: Up to 8.032 Mbps

Internal hardware

 

  • 18 MHz AM186ESLV.2 CPU
  • AD20msp918 DMT modem chipset
  • 128 KB SRAM
  • 256K x 16 boot flash
  • 2 kb serial EEPROM

Dimensions

Height: 6.07 in. (15.42 cm)
Depth: 8.50 in. (21.59 cm)
Width: 0.88 in. (2.24 cm)

Weight

0.875 lb (0.4 kg)

Power consumption

16.5W

Minimum software requirements

Cisco IOS Release 12.0(5)DA

CDM1—Release 3.2 (optional)

1CDM = Cisco DSL Manager

4xflexi Specifications

Table A-3 lists the specifications for the 4xflexi.

Table A-3   4xflexi Specifications

Specification DMT Mode CAP Mode G.lite Mode

Standards supported

ITU G.dmt (G.992.1)
ANSI T1.413 Issue 2

RADSL1

ITU G.lite (G.992.2)

Power consumption

17.5W

13.5W

13.5W

Maximum data rates (per port)

Downstream

Upstream


8.032 Mbps

864 kbps


7.168 Mbps

1.088 Mbps


1.536 Mbps

512 kbps

External interfaces

4 (no connectors on card)

Internal hardware

AMD 186-based 3.3V 18-MHz CPU

128 KB SRAM

512K flash

Dimensions

Height: 6.07 in. (15.42 cm)
Depth: 8.50 in. (21.59 cm)
Width: 0.88 in. (2.24 cm)

Weight

0.875 lb (0.4 kg)

Minimum software requirements

Cisco IOS Release 12.1(2)DA

CDM—Release 3.2 (optional)

1Rate-adaptive digital subscriber line.

4xSDSL Specifications

Table A-4 lists the specifications for the 4xSDSL.

Table A-4   4xSDSL Specifications

Specification Description

Standards supported

ITU G.991.1

External interfaces

4 (no connectors on card)

Maximum data rates (per port)

Downstream

Upstream


1168 kbps

1168 kbps

Line encoding

2B1Q

Internal hardware

AMD 186-based 3.3V 18-MHz CPU

128 KB SRAM

512K flash

Dimensions

Height: 6.07 in. (15.42 cm)
Depth: 8.50 in. (21.59 cm)
Width: 0.88 in. (2.24 cm)

Weight

0.875 lb (0.4 kg)

Power consumption

9W

Minimum software requirements

Cisco IOS Release 12.1(2)DA

CDM—Release 3.2 (optional)

DS3/2DS3 NI-2 Card Specifications

Table A-5 lists the specifications for the DS3/2DS3 NI-2 card.

Table A-5   DS3/2DS3 NI-2 Card Specifications

Specification Description

Internal hardware

150 MHz RC64475 CPU
Galileo GT64120 system controller
1M x 32 bootflash
4M x 32 Flash
512 KB boot EPROM

Dimensions

Height: 12.38 in. (31.45 cm)
Depth: 8.50 in. (21.59 cm)
Width: 1.80 in. (4.57 cm)

Weight

3.0 lb (1.36 kg)

Level 2 protocol

ATM

External interfaces

Three DS3 (44.736-Mbps) coaxial ports

Connector type

BNC1

Impedance

75 ohms (nominal)

Line encoding

B3ZS

Framing

C-bit parity, optionally PLCP with M23, otherwise Add Drop Multiplexer (ADM)

Power consumption

33.5W

Redundancy

NI-2 card redundancy only (with a second NI-2 card installed). No link redundancy.

Minimum software requirements

Cisco IOS Release 12.1(4)DA

CDM 3.2 (optional)

1The Bayonet-Neill-Concelman (BNC) connectors are located on the system I/O card which is installed on the backplane of the chassis.

OC-3c/OC-3c NI-2 Card Specifications

Table A-6 lists the specifications of the single-mode and multimode versions of the OC-3c/OC-3c NI-2 card.

Table A-6   OC-3c/OC-3c NI-2 Card Specifications

Specification Description

Internal hardware

  • 150 MHz RC64475 CPU
  • Galileo GT64120 system controller
  • 1M x 32 boot flash1 (4 MB)
  • 4M x 32 Flash (16 MB)
  • 512 KB boot EPROM

Dimensions

Height: 12.38 in. (31.45 cm)

Depth: 8.50 in. (21.59 cm)

Width: 1.80 in. (4.57 cm)

Weight

3.0 lb (1.36 kg)

Layer 2 protocol

ATM

Power consumption

33.5W

Minimum software and network management requirement

Cisco IOS

  • Non-redundant NI-2 card configurations—Release 12.1(1)DA
  • Redundant NI-2 card configurations—Release 12.1(7)DA

CDM—Release 3.0/3.2 (optional)

Single-Mode Card Multimode Card

External interfaces

Two OC-3c/STM-1 (155 Mbps) single-mode ports

Two OC-3c/STM-1 (155 Mbps) multimode ports

Connector type

SC-PC

SC-PC

Fiber type

Intermediate reach single mode

Multimode

Average transmitted power

-15 to -8 dBm

-20 to -14 dBm

Average received power

-8 dBm

-11 dBm

Transmission distance

Up to 12 miles (19.3 km)

Up to 1.2 miles (1.93 km)

Wavelength

1310 nm

1300 nm

1The version of the OC-3c/OC-3c NI-2 card with enhanced upstream bandwidth features (NI2-155SM-155SM2 and NI2-155MM-155MM2) has a 2M x 32 bootflash (8 MB).

Software Specifications

Table A-7 lists Cisco 6130 with NI-2 system software specifications.

Table A-7   Software Specifications

Specification Description

Management protocols

Cisco IOS software support for SNMP to CEMF1

Management applications

  • Cisco IOS
  • CDM (optional)

Management interfaces

In band—ATM VC

Out of band—10BaseT Ethernet, console, auxiliary

1CEMF = Cisco Element Management Framework


hometocprevnextglossaryfeedbacksearchhelp
Posted: Tue Jan 28 18:02:15 PST 2003
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.