Ch 2: Preparing for Installation

This section describes safety requirements for the Cisco 6130 with NI-2 system. Before you install the Cisco 6130 with NI-2 system, ensure that all the criteria in this section are met. The section describes the following safety requirements:

Safety Guidelines

Before working on the equipment, be aware of standard safety guidelines and the hazards involved in working with electrical circuitry to prevent accidents. Adhere to the following guidelines, cautions, and warnings and those throughout the guide for safe and hazard-free installation.

Follow these guidelines to ensure general safety:

Keep the equipment area clear and dust-free during and after installation.
Keep tools away from walk areas where you and others could fall over them.
Do not wear loose clothing that could get caught in the chassis. Fasten ties or scarves and roll up shirt sleeves.
Wear safety glasses if you are working under conditions that might be hazardous to your eyes.
Do not perform any action that makes the equipment unsafe or creates a potential hazard to yourself or others.

Tip In the following warnings, the terms cover panel and safety cover refer to the Cisco 6130 chassis front cover.

Caution Before you start the installation procedures, read the entire chapter for important information and safety warnings.

Caution Proper ESD protection is required whenever you handle Cisco equipment. Installation and maintenance personnel should be properly grounded using ground straps to eliminate the risk of ESD damage to the equipment. Cards are subject to ESD damage whenever they are removed from the chassis.

Caution Mixing incompatible line cards can cause unpredictable system behavior. See the "Cisco 6130 Cards" section for intermixing compatibility.

Caution Be careful when you remove the standoff screws and reinsert the screws into the screw holes on the backplane so that the backplane circuitry does not become damaged.

Caution Installing the cards in the chassis with the power leads reversed can damage the line cards.

Caution If fuses are already installed in the fuse and alarm panel, remove them. You can replace the fuses after the system is installed. Do not power up the system while you install and connect the system.

Caution If the power connections are improperly connected and power is applied while the cards are installed, the cards and chassis could be damaged.

Caution It is important that the chassis cooling fans run continuously while the system is powered.

Caution Any card that is only partially connected to the backplane can disrupt system operation.

Caution Periodically check the resistance value of the antistatic strap. Ensure that the measurement is between 1 and 10 megohms.

Caution Do not power up the Cisco 6130 chassis while locating or installing the system I/O card or line cards.

Caution Complete all installation procedures before powering up the Cisco 6130 system.

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Waarschuwing

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.

Varoitus

Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).

Attention

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil.

Warnung

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt. Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety Information (Informationen zu behördlichen Vorschriften und Sicherheit), das zusammen mit diesem Gerät geliefert wurde.

Avvertenza

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositivo.

Advarsel

Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og sikkerhetsinformasjon) som ble levert med denne enheten.

Aviso

Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições Reguladoras) que acompanha este dispositivo.

¡Advertencia!

Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. Para ver una traducción de las advertencias que aparecen en esta publicación, consultar el documento titulado Regulatory Compliance and Safety Information (Información sobre seguridad y conformidad con las disposiciones reglamentarias) que se acompaña con este dispositivo.

Varning!

Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning.

Warning The customer 48 volt power system must provide reinforced insulation between the primary AC power and the 48V DC output.

Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

Warning Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift with both hands. To prevent injury, keep your back straight and lift with your legs, not your back.

Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

—This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

—When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

—If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Warning Class 1 laser product.

Warning Use copper conductors only.

Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.

Warning The DS3 ports are not intended to be connected to cables that run outside the building where it is installed. For any connections outside the building, the DS3 ports must be connected to a network termination unit (NTU). NTU devices should comply with appropriate national safety standards such as UL 1950, CSA 950, EN 60950, IEC 950, and AS 3260.

Warning Never install telephone wiring during an electrical storm.

Warning Do not reach into a vacant slot or chassis while you install or remove a card or a fan module. Exposed circuitry could constitute an energy hazard.

Warning Ethernet cables must be shielded when used in a central office environment.

Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the terminal block plug.

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, and front covers are in place.

Warning When installing the unit, the ground connection must always be made first and disconnected last.

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.

Warning This equipment needs to be grounded. Use a green and yellow 12 to 14 American Wire Gauge (AWG) ground wire to connect the host to earth ground during normal use.

Warning Incorrect connection of this or connected equipment to a general purpose outlet could result in a hazardous situation.

Warning Read the installation instructions before you connect the system to its power source.

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact. Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or connection hardware. Any hardwired connection (other than by a nonremovable, connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers.

Warning Do not stare into the beam or view it directly with optical instruments.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Warning Use caution when installing or modifying telephone lines.

Warning This unit has more than one power supply connection; all connections must be removed completely to completely remove power from the unit.

Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 104°F (40°C).

Warning Metal objects heat up when connected to power and ground, and can cause serious burns.

Warning Secure all power cabling when installing this unit to avoid disturbing field-wiring connections.

Warning The power supply circuitry for the equipment can constitute an energy hazard. Before you install or replace the equipment, remove all jewelry (including rings, necklaces, and watches). Metal objects can come into contact with exposed power supply wiring or circuitry inside the equipment. This could cause the metal objects to heat up and cause serious burns or weld the metal object to the equipment.

Warning Ultimate disposal of this product should be handled according to all national laws and regulations.

Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location.

Warning Connect the unit only to DC power source that complies with the Safety Extra-Low Voltage (SELV) requirements in IEC 60950 based safety standards.

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations.

Warning Care must be given to connecting units to the supply circuit so that wiring is not overloaded.

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Warning Do not use a telephone to report a gas leak in the vicinity of the leak.

Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.

Maintaining Safety with Electricity

Follow these guidelines when working on equipment that is powered by electricity:

Locate the emergency power-off switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn off the power.
Disconnect all power by removing the fuses from the fuse and alarm panel before:

Installing or removing a chassis
Working near power supplies

Do not work alone if potentially hazardous conditions exist.
Never assume that power is disconnected from a circuit; always check the circuit.
Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, frayed power cords, and missing safety grounds.
If an electrical accident occurs, proceed as follows:

Use caution; do not become a victim yourself.
Turn off power to the system.
If possible, send another person to get medical aid. Otherwise, assess the condition of the victim and then call for help.
Determine if the person needs rescue breathing or external cardiac compressions; then, take appropriate action.

Preventing Electrostatic Discharge Damage

Proper ESD protection is required whenever you handle Cisco equipment. ESD damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Use an antistatic strap during handling.

Follow these guidelines to prevent ESD damage:

Always use an ESD ankle or wrist strap and ensure that it makes good skin contact.
Connect the equipment end of the strap to the ESD jack on the front right side of the chassis.
When you install a component, use available ejector levers or captive installation screws to properly seat the bus connectors in the backplane or midplane. These devices prevent accidental removal, provide proper grounding for the system, and help ensure that bus connectors are properly seated.
When you remove a component, use available ejector levers or captive installation screws to release the bus connectors from the backplane or midplane.
Handle the system I/O card by the edges only; avoid touching the printed circuit boards or connectors.
Avoid touching the printed circuit boards or connectors on the NI-2 cards or line cards.
Place a removed component board-side-up on an antistatic surface or in a static-shielding container. If you plan to return the component to the factory, immediately place it in a static-shielding container.
Avoid contact between the printed circuit boards and clothing. The wrist strap protects components from ESD voltages on the body only; ESD voltages on clothing can still cause damage.

Caution Periodically check the resistance value of the antistatic strap. Ensure that the measurement is between 1 and 10 megohms.

General Maintenance Guidelines

This section covers the following topics:

Hot Swapping Cards

Hot swapping allows you to remove and replace cards without disconnecting the system power. The Cisco 6130 chassis supports hot swapping for the following cards:

Quad-port Discrete Multitone (DMT) ATU-C line card (4xDMT), quad-port flexi ATU-C line card (4xflexi), or quad-port STU-C line card (4xSDSL)—These line cards can be hot swapped. When the system detects that you have added or removed a line card, it automatically runs diagnostic and discovery routines and acknowledges the presence or absence of the line card. Hot swapping a line card will interrupt service for the subscribers assigned to that particular line card until the card is replaced.

If you remove a line card and replace it with the same type of line card, the newly installed line card receives the same provisioning as the original line card. The system resumes operation without any operator intervention.

If an unprovisioned line card is installed for the first time, the system identifies it as present but unprovisioned. Instructions for provisioning the line card are found in the appropriate software guide for your chassis.

DS3/2DS3 or OC-3c/OC-3c NI-2 card—Hot swapping the NI-2 card will interrupt service for the entire system until the NI-2 card is replaced.

Installation and Replacement Suggestions

The following bullets list examples of recommended installation and replacement practices for the Cisco 6130 system cards.

Caution Any card that is only partially connected to the backplane can disrupt system operation.

Do not force the card into or onto the chassis backplane connectors. This action can damage the pins on the connectors if they are not aligned properly with the card.
Do not force the line card into its slot. This action can damage the pins on the backplane if they are not aligned properly with the line card.
Ensure that the system I/O card is straight and parallel to the chassis backplane when you install the card onto the connectors. The pins on the connectors can be damaged if the card is not installed correctly.
Ensure that the card is straight and not at an angle when you install the card in the slot. Installing the card at an angle can damage the card. Use the guide rails to install the card correctly.
Fully depress the ejector tabs to ensure that the card connector mates with the backplane correctly. Firmly seat the card in the slot by locking the card.

Site Requirements

This section describes requirements for the site where the Cisco 6130 with NI-2 system will be installed. Before you install the Cisco 6130 with NI-2 system, ensure that all the criteria in this section are met. The section describes the following:

Environmental Requirements

Proper operation of the Cisco 6130 with NI-2 system depends on a proper environment. This section describes environmental requirements for the site where you will install the Cisco 6130 with NI-2 system. The section describes the following requirements:

Temperature, Altitude, and Humidity

The system can tolerate a wide range of temperatures. Table 2-1 provides the Cisco recommendations for temperature, altitude, and humidity conditions in a CO environment.

Table 2-1 CO Operating Environment Requirements

Environmental Specifications	Description
Temperature Altitude Humidity	41 to 104ºF (5 to 40ºC)—Operating 23 to 131ºF (-5 to 55ºC)—Short-term operating -60 to 3200 meters 5 to 90% (noncondensing)

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 104°F (40°C).

Ventilation

The following practices ensure proper ventilation for the Cisco 6130 with NI-2 system:

Chassis placement—Leave 1 rack unit (RU) of space under the fan tray. The space is for the intake plenum and for the pass-through cables to the NI-2 card.
Fan tray installation—A fan tray must be installed under each Cisco 6130 chassis.
POTS splitter location—The POTS splitters do not dissipate heat and should be positioned at the bottom of the rack.

Space

You can install a combination of the following Cisco 6130 with NI-2 system components in a 7-foot rack:

Cisco 6130 chassis—Maximum of two chassis are allowed per rack
POTS splitter (Cisco 6120 or other third-party POTS splitter)—Required in a Cisco 6130 with a POTS splitter configuration only
Fan tray—Required under each Cisco 6130 chassis

The Cisco 6130 with NI-2 system fits in a 23-inch wide rack. See Table 2-2 for individual rack space requirements.

Table 2-2 Rack Space Requirements

Component	Rack Space	Height	Depth
Cisco 6130	9 RUs¹	15.75 in. (40.00 cm)	12 in. (30.48 cm)
Cisco 6120	4 RUs	7 in. (17.78 cm)	12 in. (30.48 cm)
Fan tray²	2 RUs	3.5 in. (8.89 cm)	12 in. (30.48 cm)

1An RU is equal to 1.75 inches (4.45 cm).

2Leave 1 RU of space under the fan tray. This space allows for the intake plenum and for cabling back to front for the NI-2 card.

Note A system configuration using quad-port line cards requires a POTS splitter that expands the system capacity to 128 subscriber ports. Depending on the POTS splitter selected for your configuration (Cisco 6120 or third-party), the installation of an additional POTS splitter may be necessary. Each Cisco 6120 POTS splitter supports up to 64 subscribers.

Depending on your configuration type, plan accordingly so that the central office (CO) rack accommodates your needs. Use Table 2-3 to calculate the rack space necessary for your Cisco 6130 with NI-2 system configuration. The total amount of rack space should not exceed 42 RUs. If your total configuration exceeds 42 RUs, either replan your configuration or use more than one rack to house the Cisco 6130 with NI-2 system components.

Table 2-3 Rack Space Calculation for the Cisco 6130 with NI-2 System Configurations

Line	Instructions	Calculation
Cisco 6130 with a POTS Splitter Configuration
1	Total number of Cisco 6130 chassis in the rack—Maximum is two chassis per rack (include subtending host and subtended node chassis).
2	Total number of fan trays in the rack—Must equal line 1.
3	Total number of POTS splitters¹ in the rack
4	Multiply 10 RUs by the total number of chassis on line 1 (with every tenth RU reserved for the intake plenum of each chassis).
5	Multiply 2 RUs by the total number of fan trays on line 2.
6	Multiply 4 RUs by the total number of POTS splitters on line 3.
7	Add lines 3 through 6 for the total number of RUs needed with your Cisco 6130 with a POTS splitter configuration.
Cisco 6130 Without a POTS Splitter Configuration
8	Total number of Cisco 6130 chassis in the rack—Maximum is two chassis per rack (include subtending host and subtended node chassis).
9	Total number of fan trays in the rack—Must equal line 8.
10	Multiply 9 RUs by the total number of chassis on line 8.
11	Add 1 RU for the intake plenum (1 RU for each chassis on line 8).
12	Multiply 2 RUs by the total number of fan trays on line 9.
13	Add lines 10 through 12 for the total number of RUs needed with your Cisco 6130 without a POTS splitter configuration.

1Either a Cisco 6120 or a third-party POTS splitter can be used in a Cisco 6130 with a POTS splitter configuration.

Power

The central office (CO) power source or rectifier supplies external power to the system as -48V DC from the fuse and alarm panel. Power connections from the fuse and alarm panel are wired separately to the Cisco 6130 chassis and the fan tray. Connections for single- and dual-power feeds are provided. The power input connections are redundant, and only one is absolutely necessary for system operation. The nominal voltage is -48V DC; the minimum operating value is -36V DC; and the maximum operating value is -60V DC.

Before you connect the system to a power source, verify that the power source is properly grounded and that it falls within the internal power supply rating.

Depending on your configuration type, calculate the typical power required for each Cisco 6130 system component. After you calculate the typical power, determine the minimum fuse value for each component that is wired to the fuse and alarm panel. Use Table 2-4 to calculate the minimum fuse rating that is necessary for each of your Cisco 6130 with NI-2 system components.

Note The power rating label that is supplied on the rear of each chassis and fan tray indicates the maximum fuse value for the chassis or the fan tray.

Table 2-4 Fuse Calculation for the Cisco 6130 with NI-2 System Components

Line	Instructions	Calculation
Cisco 6130 chassis¹
1a	If you are using 4xDMTs, multiply 16.5W by the total number of 4xDMT line cards in the Cisco 6130.
1b	If you are using 4xflexis (CAP or G.lite mode), multiply 13.5W by the total number of 4xflexi (CAP or G.lite mode) line cards in the Cisco 6130.
1c	If you are using 4xflexis (DMT mode), multiply 17.5W by the total number of 4xflexi (DMT mode) line cards in the Cisco 6130.
1d	If you are using 4xSDSLs, multiply 9W by the total number of 4xSDSL line cards in the Cisco 6130.
2	Add the amounts for lines 1a through 1d.
3	Enter 33.5W for each NI-2 card in the Cisco 6130.
4	Add lines 2 and 3. This is the typical power required for the Cisco 6130.
5	Divide line 4 by 48. This is the nominal current for the Cisco 6130.
6	Multiply line 5 by 1.25. This is the minimum fuse rating needed to operate the Cisco 6130 in your system.
Fan Tray
7	A 1.25A fuse is required for each fan tray that is wired to the fuse and alarm panel. A fan tray must be installed under each Cisco 6130 chassis.

1Complete this section for each subtending host.

Cables

For detailed information about required cables, refer to "Cable and Port Mapping Specifications."

Rack-Mounting

Cisco recommends that you mount the Cisco 6130 with NI-2 system in a rack. Ensure that vertical hole spacing on the rack rails meets standard EIA-310-C requirements—1 inch (2.54 cm) spacing. All portions of the rack are equal to or less than the NEBS maximum allowances of 12 inches (30.48 cm).

When you install the Cisco 6130 with NI-2 system in a rack, be sure to allow enough room to access the backplane of the unit for wiring and cabling purposes. The majority of the connectors are located on the backplane.

Required Tools and Equipment

Table 2-5 lists the tools and equipment required to install and remove the Cisco 6130 with NI-2 system components:

Table 2-5 Tool and Equipment Requirements Checklist

Check	Tools and Equipment
	Hardware Components
	Cisco 6130 chassis
	4xDMTs
	4xflexis
	4xSDSLs
	NI-2 card(s): DS3/2DS3, OC-3c/OC-3c SMF¹, or OC-3c/OC-3c MMF²
	System I/O card for NI-2 system (if it is not already installed on the Cisco 6130 backplane)—Kit 800-07027-01 Plastic ESD shield Component safety shield EMI cover and cover bracket Screws
	Blank faceplates
	Cisco 6120 or third-party vendor POTS splitter³
	DMT POTS cards
	Fan Tray
	Fan tray alarm cable (part number 72-1912-01)
	Rear cover (optional)
	Front cover
	Champ cables (see "Cable and Port Mapping Specifications" for cable information)
	Software Components
	Cisco IOS CDM⁴ (optional)
	Tools
	A 3/16-inch flat-head screwdriver
	A Phillips-head screwdriver
	A one-quarter inch socket driver or wrench
	Necessary equipment for ESD protection—Required whenever you handle Cisco equipment, which includes the chassis and cards
	Mounting screws—To mount the Cisco 6130, Cisco 6120, and fan tray to the rack
	Standoff screws
	Backplane screws—Included on the backplane
	Wire-wrapping tool
	Wire stripper
	Wire for connections 12 AWG black and red copper solid or stranded—Used for Cisco 6130 chassis power connections 14 to 18 AWG black and red copper solid or stranded—Used for fan tray power connections 12 AWG or thicker green or green with yellow stripes copper stranded—Used for the Cisco 6130 chassis grounding 14 AWG or thicker green or green with yellow stripes copper stranded—Used for the fan tray and POTS splitter grounding
	Ferrites that yield an impedance of 200 ohms +/-20 percent at 100 MHz
	Tie wraps
	Coaxial cable—Used to connect the DS3/2DS3 NI-2 card Type 734A or equivalent Type 735A or equivalent
	Fiber cable—Used to connect the OC-3c/OC-3c NI-2 card
	Fiber cable (additional)—Used for fiber redundancy if the Cisco 6130 chassis has a secondary OC-3c/OC-3c NI-2 card
	RJ-45 serial cable to connect the console and auxiliary connectors
	RJ-45 connector, straight-through 10BaseT/100BaseTX Ethernet, half/full-duplex compliant with IEEE 802.3

1SMF = single-mode fiber.

2MMF = multimode fiber.

3The Cisco 6120 or third-party vendor POTS splitter is used in a Cisco 6130 with a POTS splitter configuration only.

4CDM = Cisco DSL Manager.

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Note The Cisco 6130 with NI-2 system has no internal user-serviceable parts. However, you can add or remove a line card or a fan module without removing power from the system. This action is called hot swapping. See the "Hot-Swappable FRUs" section 5-2 for more information.

Unpacking the Cisco 6130 System

Each Cisco 6130 with NI-2 system chassis is securely packaged in a shipping box. The Cisco 6130 with NI-2 system components ship either:

With the line cards installed in the chassis and any additional line cards packaged separately.
Without the line cards installed in the chassis. Each line card is individually packaged in its own antistatic carrier.

The line card antistatic carriers ship together in a box. The NI-2 card is packed in its own antistatic bag, which is housed in foam inserts and shipped in a separate box.

To unpack the Cisco 6130 with NI-2 system, complete the following steps:

Step 1 Inspect the packing containers. If any damage or other signs of mishandling are evident, inform both the local freight carrier and Cisco before unpacking. Your freight carrier can provide you with the procedures necessary to file a claim for damages.

Step 2 Carefully open the box.

Step 3 Remove all packing material.

Step 4 Remove the chassis from the box.

Step 5 Carefully open the additional boxes, remove the packing material, and remove the cards.

Step 6 Open the accessory kits and boxes that contain the cables, ferrites, documentation, and management software. Do not use a knife to open these boxes.

Verifying Contents

To verify that all equipment, cables, documentation, and so forth are received, compare the packing list to your shipment and to your order. If any items are missing or you need additional information, contact the Cisco Technical Assistance Center (TAC) at one of the following:

800 553-2447
408 526-7209
tac@cisco.com

Inspecting for Damage

After you verify that all of the equipment is included, carefully examine the assemblies, cards, and cables for any damage resulting from shipping. If you suspect any damage from shipping, contact your local freight carrier for procedures on damage claims.

If you observe any physical defects in the items you ordered, obtain standard warranty service by delivering the defective part, accompanied by a copy of the dated proof-of-purchase, to the Cisco Systems Corporate Service Center or an Authorized Cisco Systems Service Center during the applicable warranty period. Contact the Cisco TAC for the location of your nearest service center.

See the back of the title page for the Cisco Systems warranty information for hardware and software products.

Table of Contents

Preparing for Installation

Safety Requirements