|
|
Table Of Contents
Installing the Operating System on the SC Hosts
Installing the Sun Solaris 2.6 Operating System
Loading the Sun Solaris 2.6 Operating System
Installing the Sun Solaris Patches
Installing the Alarm Card Software
Configuring a Second Ethernet Interface
Configuring a Second Disk Drive
Installing Log and Spool File Systems
Installing the Operating System on the SC Hosts
This chapter describes installation of the Sun Solaris 2.6 operating system, Solaris patches, alarm card software, and Volume Manager software on the SC host.
Note
This chapter is provided only for upgrades from the Cisco DAS Release 2.0 to the Cisco SS7 Interconnect for Access Servers Solution Release 2.x. Other solution upgrades do not require that the steps in this chapter be performed.
Note
This chapter contains the following sections:
•
•
•
•
Note
{O} okprompt. To power on a CPU, push both tabs outward (away from the center). When you are instructed to power off a CPU in the procedures that follow, pull both tabs on the CPU toward the center.
Tip
Before You Start
Note
•
–
–
–
–
–
•
Caution
•
–
–
–
–
–
Note
•
–
–
•
–
–
–
•
•
•
Tip
Connecting to the SC Host
Connect your laptop processor's COM port to Port A on the SC host, and open a console connection using a terminal emulation program (such as Reflection). Cisco recommends selecting DEC VT100 as the terminal type. The PC Console terminal type does not work very well.
Note
Your software should have been stopped if you backed up your data per the instructions in "Backing Up Your SC Host Data" To verify that the software is stopped, proceed to the "Stopping the SC Software" section.
Stopping the SC Software
Step 1
va-cerulean% ps -ef | grep tranStep 2
va-lions:8> /etc/init.d/transpath stopSignalling procM to shut down...shutdown complete
Caution
Step 3
ps -ef | grep procMMake sure that you receive no response.
Installing the Sun Solaris 2.6 Operating System
This section provides instructions for installing the operating system on the Sun Netra t 1120, t 1125, and E450 platforms. There are points in the instructions when the responses you make to prompts depend on the disk drive size or other particulars of your system. These places are pointed out as you go.
This section contains the following procedures:
•
•
•
•
•
Booting from a Local CD-ROM
To boot from a local CD-ROM, perform the following steps:
Step 1
Caution
Note
Step 2
# init 0Step 3
okprompt, boot the CD-ROM:{0} ok boot cdrom
Note
If the machine has never had an operating system installed, the following screen appears when the CD-ROM boot is finished:
Boot device: /pci@1f,4000/scsi@3/disk@6,0:f File and args:SunOS Release 5.7 Version Generic_106541-06 [UNIX(R) System V Release 4.0]Copyright (c) 1983-1999, Sun Microsystems, Inc.Solaris Web Start 3.0 installerNo frame buffer found.Command line install is available in english only.English has been selected as the language in which to perform the install.Starting the Web Start 3.0 Solaris installerSolaris installer is searching the system's hard disks for alocation to place the Solaris installer software.The default root disk is /dev/dsk/c0t0d0.The Solaris installer needs to format/dev/dsk/c0t0d0 to install Solaris.WARNING: ALL INFORMATION ON THE DISK WILL BE ERASED!Do you want to format /dev/dsk/c0t0d0? [y,n,?,q]If an operating system was previously installed on the machine, text similar to the following appears with two warnings:
Command line install is available in english only.English has been selected as the language in which to perform the install.Starting the Web Start 3.0 Solaris installerSolaris installer is searching the system's hard disks for alocation to place the Solaris installer software.This system appears to contain a version of Solaris.The Solaris installer does not allow upgrading. If youchoose to use this installer an initial install will berequired. Any information on your system's disks could be erased.Would you like to use this installer? [y,n,?]Step 4
Enter a swap partition size between 320Mb and 17269Mb, default = 512Mb [?]Step 5
You have selected /dev/dsk/c0t0d0 with a swap size of 2040/320 to be used by the Solaris installer.WARNING: ALL INFORMATION ON THE DISK WILL BE ERASED!Is this OK [y,n,?,q]Step 6
Tips
The following text appears:
Welcome to the Web Start Solaris Command Line installation!The following questions will gather information about this system.This information will be used to configure:NetworkName ServiceDate and TimeRoot PasswordPower Management<Press Return to continue>Step 7
Please enter a host name, which identifies this system on the network. The name must be unique within the domain in which it resides; creating a duplicate host name will cause problems on the network after you install Solaris.A host name must be at least two characters; it can contain letters, digits, and minus signs (-).Enter host name: <host-name>Step 8
Note
The following text appears:
Please specify whether your system will be networked. Specify Yes if thesystem is connected to the network by one of the Solaris or vendornetwork/communication Ethernet cards that are supported on the Solaris CD. Seeyour hardware documentation for the current list of supported cards.Specify No if the system is connected to a network/communication card that isnot supported or not connected to a network.Is this machine networked (y/n) [n]?Step 9
Please enter the Internet Protocol (IP) Address for this system. It must be unique and follow your site's address conventions, or a system/network failure could result.IP Addresses contain four sets of numbers separated by periods (for example 129.200.9.1).Enter this machine's IP Address:Step 10
Please specify the netmask of your subnet. A default netmask is shown; do not accept the default unless you are sure it is correct for your subnet. A netmask must contain four sets of numbers separated by periods (for example 255.255.255.0).Enter the subnet netmask [255.255.255.0]:Step 11
Caution
The following text appears:Please provide name service information. Select the name service that will be used by this system, or None if your system will either, not use a name service at all, or if it will use a name service not listed hereAvailable name services:1. NIS+2. NIS3. DNS4. NonePlease enter the number corresponding to the type of name service youwould like [ ]:Step 12
Please select how to specify your default time zone.Specify Time Zone by:1. Geographic region2. Offset from GMT3. Time zone filePlease enter the number corresponding to how you would like to specifythe time zone [1]:Step 13
The default date and time is (current date and time of defined time zone). Do you want to use this date and time (y/n) [y]?Step 14
Type in an alphanumeric string to be used as the root password for the computer you are setting up.Enter the root password []:Step 15
Retype the above password for confirmation.Enter the root password again []:Step 16
Do you want Power Management turned on (y/n) [n]?Step 17
You can choose to be asked the preceding question every time you reboot the system. Alternatively, you can choose never to be asked about Power Management again.Ask about Power Management at each reboot (y/n) [n]?Step 18
You have entered the following values:Host Name: host-nameIP Address: IP_addressSystem part of a subnet: YesNetmask: IP_netmaskName Service: NONETime Zone: time_zonePower Management:Turn Power Management OffDo not ask about Power Management at reboot.Enter 'y' to apply these values and proceed to the next stage of theinstallation, or 'n' to return to the beginning and make changes (y/n):Step 19
a.
b.
This completes the process of booting from a local CD. Continue with the "Loading the Sun Solaris 2.6 Operating System" section.
Loading the Sun Solaris 2.6 Operating System
This section provides the procedure for loading the Sun Solaris 2.6 operating system.
Note
Step 1
keyserv: failed to generate host's netname when establishing root's key.Solaris Web Start will now gather information to install software for Solaris.Please wait while initial values are loaded...Available operating environments:1. Solaris 2.5.1 Hardware: 11/972. Solaris 2.6 5/98Select the number corresponding to the operating environment you would like to install [1]:Step 2
You have selected:Solaris OS: Solaris 2...6Enter 'y' if this is correct, or 'n' if it is incorrect:Step 3
Please insert the Solaris 2.6 CD.<Press Return after the CD has been inserted>Step 4
Reading CD for Solaris 2.6Please wait while the system is initializing...To install basic Solaris products into their default directory locations, select Default Install.Custom install provides a choice of which Solaris products to install. For each product, it also provides an option to further customize the products install.Types of install available:1. Default Install2. Custom InstallSelect the number corresponding to the type of install you would like [1]:Step 5
Select the software localizations you want to install. The English version of Solaris will be installed by default.Enable locale German ( de ) (y/n) [n]?Step 6
Enable locale Spanish ( es ) (y/n) [n]?Step 7
Enable locale French ( fr ) (y/n) [n]?Step 8
Enable locale Italian ( it ) (y/n) [n]?Step 9
Enable locale Swedish ( sv ) (y/n) [n]?Step 10
Available locales:1. English (Australia) ( en_AU )2. English (Canada) ( en_CA )3. English (Ireland) ( en_IE )4. English (New Zealand) ( en_NZ )5. English (UK) ( en_UK )6. English (United States) ( en_US )7. English (POSIX C) ( C )Select the number corresponding to the desired system locale [6]:Step 11
Available software groups:1. Entire Solaris Software Group Plus OEM2. Entire Solaris Software Group3. Developer Solaris Software Group4. End User Solaris Software Group5. Core Solaris Software GroupSelect the number corresponding to the desired Solaris software group [2]:Step 12
Please wait while the system is initializing...Select which disks you want to lay out the file systems on.Required disk space: 2,705 MBOne of the following tables appears, depending on your disk size:
---------------------------------------------9 Gbyte disk driveAvailable DisksDisk Sizec0t0d0 8633 MBc0t1d0 8633 MB---------------------------------------------18 Gbyte disk driveAvailable Disks:Disk Sizec0t0d0 17269 MBc0t1d0 17269 MB---------------------------------------------
Tips
You also see the following prompt:
Enter 'y' to layout file systems on the specified disk. This will erase all existing data on the disk. Enter 'n' to leave the disk unmodified.Layout file systems on disk c0t0d0 (bootdisk) (y/n) [y]?Step 13
Layout file systems on disk c0t1d0 (y/n) [n]?Step 14
File System operations:1. Print the current partition table2. Modify a disk's partition table3. DoneSelect the number corresponding to a file system operation, or 'Done' toproceed with the install [3]:Step 15
---------------------------------------------9 Gbyte disk driveAvailable disks:1. c0t0d0/ 668 MBswap 2040 MB/export/home 14561 MB2. c0t1d0 Not Selected3. Done---------------------------------------------9 Gbyte disk driveAvailable disks:1. c0t0d0/ 667 MBswap 2040 MB/export/home 5926 MB2. c0t1d0 Not Selected3. Done---------------------------------------------You also see the following prompt:
Select a disk to modify, or Done to return to the previous menu [3]:Step 16
---------------------------------------------18 Gbyte disk driveDisk Name c0t0d0TotalSpace 17269Used Space 17269Free Space 0Round Error 0# Slice Name Slice Size Minimum Size0. / 668 MB 665 MB1. swap 2040 MB 2040 MB3. Unused4. Unused5. Unused6. Unused7. /export/home 14561 MB 0 MB8. Done---------------------------------------------9 Gbyte disk driveDisk Name c0t0d0TotalSpace 8633Used Space 8633Free Space 0Round Error 0# Slice Name Slice Size Minimum Size0. / 667 MB 665 MB1. swap 2040 MB 2040 MB3. Unused4. Unused5. Unused6. Unused7. /export/home 5926 MB 0 MB8. Done---------------------------------------------Step 17
Select a slice to modify, or Done to return to the previous menu [8]:Step 18
Enter new slice name:Step 19
Step 20
Note
Step 21
Enter new slice name:Step 22
Enter new slice size (in MB) [default]:
Note
Step 23
---------------------------------------------18 Gbyte disk driveDisk Name c0t0d0TotalSpace 17269Used Space 17208Free Space 61Round Error 0# Slice Name Slice Size Minimum Size0. / 668 MB 619 MB1. swap 2040 MB 2040 MB3. Unused4. /opt 11040 MB 25 MB5. /var 1025 MB 22 MB6. /usr 2435 MB 0 MB7. Unused8. Done---------------------------------------------9 Gbyte disk driveDisk Name c0t0d0TotalSpace 8633Used Space 8627Free Space 15Round Error 0# Slice Name Slice Size Minimum Size0. / 512 MB 42 MB1. swap 2040 MB 2040 MB3. overlap 86330 MB4. /opt 4530 MB 25 MB5. /var 1025 MB 22 MB6. /usr 512 MB 578 MB7. Unused8. Done---------------------------------------------Select a slice to modify, or Done to return to the previous menu:Step 24
---------------------------------------------9 Gbyte disk driveAvailable disks:1. c0t0d0/ 512 MBswap 2048 MBoverlap 8633 MB/opt 4530 MB/var 1025 MB/usr 512 MB2. c0t1d0 Not Selected3. Done---------------------------------------------18 Gbyte disk driveAvailable disks:1. c0t0d0/ 668 MBswap 2040 MB/opt 11040 MB/var 1025 MB/usr 2435 MB2. c0t1d0 Not Selected3. Done---------------------------------------------Select a disk to modify, or Done to return to the previous menu [3]:Step 25
File System operations:1. Print the current partition table2. Modify a disk's partition table3. DoneSelect the number corresponding to a file system operation, or 'Done' toproceed with the install [3]:Step 26
The following items will be installed:Solaris OS: Solaris 2.6Software Locales: noneSystem Locale: English (United States) ( en_US )Solaris Software Group: Entire Solaris Software Group Plus OEMEnter 'y' to accept these values and start the installation, or 'n' toreturn to the beginning and make changes (y/n):Step 27
The process takes approximately 30 minutes to run and does not require user intervention. The following screen gradually appears:
Installing...Installing Solaris software group|-1%------------25%----------------50%----------------75%-------------100%|Installing Additional Software|-1%------------25%----------------50%----------------75%-------------100%|Installation details:Product Result More Info1. Solaris 2.6 5/98 Installed Available2. Additional Software Installed Available3. DoneEnter the number corresponding to the desired selection for moreinformation, or Done to continue [3]:Step 28
The system needs to reboot to complete installation.<Press Return to reboot>Step 29
Step 30
Step 31
# route add default default router IP address 1
Note
Step 32
# echo default gateway IP address > /etc/defaultrouterStep 33
pkginfo | grep ntpThe following text displays:
system SUNWntpr NTP, (Root)system SUNWntpu NTP, (Usr)
Note
Step 34
# echo "server <NTP server address>" > /etc/inet/ntp.confStep 35
# init 6Step 36
Step 37
ps -ef | grep ntpThe following text displays:
root 224 1 0 13:59:25 ? 0:00 /usr/lib/inet/xntpdsiggen 424 415 0 14:15:28 pts/1 0:00 grep ntpvao-siggen-1%This completes the installation of the Sun Solaris 2.6 operating system. Proceed to the "Installing the Sun Solaris Patches" section. If you have questions or need assistance, see the "Obtaining Technical Assistance" section on page xviii.
Installing the Sun Solaris Patches
In this section, the patch cluster is installed on the target machine.
To install the Sun Solaris 2.6 patches, perform the following steps:
Step 1
Step 2
# pkgadd -d cdrom/cdrom0/solaris_patches/CSCOh007.pkgThe following screen appears:
The following packages are available:1 CSCOh007 Media Gateway Controller Solaris 2.6 patch clusterSelect package(s) you wish to process (or 'all' to processall packages). (default: all) [?,??,q]:Step 3
Processing package instance <CSCOh007> from </cdrom/ciscomgc_install/CSCOh007.pkg>Media Gateway Controller Solaris 2.6 patch cluster(sparc) 1.0(1)Cisco System, Inc.The selected base directory </opt/sun_install> must exist beforeinstallation is attempted.Do you want this directory created now [y,n,?,q]Step 4
Using </opt/sun_install> as the package base directory.## Processing package information.## Processing system information.1 package pathname is already properly installed.## Verifying disk space requirements.## Checking for conflicts with packages already installed.The following files are already installed on the system and are beingused by another package:* /opt/sun_install <attribute change only>* - conflict with a file which does not belong to any package.Do you want to install these conflicting files [y,n,?,q]Step 5
## Checking for setuid/setgid programs.This package contains scripts which will be executed with super-userpermission during the process of installing this package.Do you want to continue with the installation of <CSCOh007> [y,n,?]Step 6
Installing Media Gateway Controller Solaris 2.6 patch cluster as <CSCOh007>## Executing preinstall script.Platform is SUNW,Ultra-60NOTICE: Architecture checks passed## Installing part 1 of 1./opt/sun_install/checkPackages2.6/opt/sun_install/checkPatches2.6/opt/sun_install/installPatches2.6/opt/sun_install/packages2.6/opt/sun_install/patch_optional2.6/opt/sun_install/patch_order2.6/opt/sun_install/patch_required2.6/var/tmp/105181-19.tar.Z/var/tmp/105210-27.tar.Z../var/tmp/108199-01.tar.Z/var/tmp/108201-01.tar.Z[ verifying class <none> ]## Executing postinstall script.!!!! You must now change directories to /opt/sun_install and!! run the installPatches2.6 script as root.!!Installation of <CSCOh007> was successful.Step 7
# cd /opt/sun_installStep 8
# ./installPatches2.6
Note
The following screen appears:
*** InstallPatches2.6 begins Thu Mar 16 10:49:01 GMT 2000 ***Platform is SUNW,Ultra-60Changed to /var/tmp directoryUncompressing 106125-08 ...Extracting 106125-08 ...Extraction of patch 106125-08 successfulInstalling 106125-08 .....Uncompressing 105591-07 ...Extracting 105591-07 ...Extraction of patch 105591-07 successfulInstalling 105591-07 ...*** InstallPatches2.6 ends Thu Mar 16 11:07:38 GMT 2000 ***This completes the installation of the Sun Solaris patches. If you have questions or need assistance, see the "Obtaining Technical Assistance" section on page xviii.
If you need alarm card software, continue to the "Installing the Alarm Card Software" section. If you do not need alarm card software, continue to the "Configuring a Second Ethernet Interface" section .
Installing the Alarm Card Software
To install the alarm card software for the Sun Netra t 112x, perform the following steps:
Step 1
Step 2
# cd /cdrom/netrat_11xx_1_0# pkgadd -d .The following packages are available:1 SUNWtsalm TS91 Alarm and Monitor Manpages(sparc.sun4u) 1.0,REV=1.12 SUNWtsalr TS91 Alarm and Monitor driver(sparc.sun4u) 1.0,REV=1.13 SUNWtsalu TS91 Alarm and Monitor Utilities(sparc.sun4u) 1.0,REV=1.1Select package(s) you wish to process (or 'all' to processall packages). (default: all) [?,??,q]:Step 3
Processing package instance <SUNWtsalm from </cdrom/netrat_11xx_1_0TS91 Alarm and Monitor Manpages(sparc.sun4u) 1.0,REV=1.1Copyright 1997 Sun Microsystems, Inc. All Rights Reserved.Manufactured in the United States of America.2550 Garcia Avenue, Mountain View, California, 94043-1100 U.S.A.Copyright 1997 Sun Microsystems Inc. Tous droits reserves.Fabrique aux Etats-Unis, 2550 Garcia Avenue, Mountain View, Californie94043-1100 USA...Installing TS91 Alarm and Monitor Manpages as <SUNWtsalm...Installation of <SUNWtsalm was successful.Processing package instance <SUNWtsalr from </cdrom/netrat_11xx_1_0TS91 Alarm and Monitor driver(sparc.sun4u) 1.0,REV=1.1Copyright 1997 Sun Microsystems, Inc. All Rights Reserved.Manufactured in the United States of America.2550 Garcia Avenue, Mountain View, California, 94043-1100 U.S.A.Do you want to continue with the installation of <SUNWtsalr [y,n,?]Step 4
Installing TS91 Alarm and Monitor driver as <SUNWtsalr...Installation of <SUNWtsalr was successful.Processing package instance <SUNWtsalu from </cdrom/netrat_11xx_1_0TS91 Alarm and Monitor Utilities(sparc.sun4u) 1.0,REV=1.1Copyright 1997 Sun Microsystems, Inc. All Rights Reserved.Manufactured in the United States of America.2550 Garcia Avenue, Mountain View, California, 94043-1100 U.S.A....Installation of <SUNWtsalu was successful.The following packages are available:1 SUNWtsalm TS91 Alarm and Monitor Manpages(sparc.sun4u) 1.0,REV=1.12 SUNWtsalr TS91 Alarm and Monitor driver(sparc.sun4u) 1.0,REV=1.13 SUNWtsalu TS91 Alarm and Monitor Utilities(sparc.sun4u) 1.0,REV=1.1Select package(s) you wish to process (or 'all' to processall packages). (default: all) [?,??,q]:Step 5
Step 6
#prompt and pressing Enter:# cd /# ejectThis completes the installation of the Sun Solaris 2.6 software and patches.
If you have an asynchronous serial port card, continue to the "Installing the SAI/P Drivers" section.
To add an optional second Ethernet interface, continue to the "Configuring a Second Ethernet Interface" section.
If you have a second disk drive to configure, also see the "Configuring a Second Disk Drive" section.
If neither of these cases apply to your installation, continue with the next step in your chosen upgrade procedure in Chapter 1, "Solution-Level Upgrade Procedures."
If you have questions or need assistance, see the "Obtaining Technical Assistance" section on page xviii.
Installing the SAI/P Drivers
To install the Serial Asynchronous Interface/PCI (SAI/P) drivers if you have an asynchronous serial port card, perform the following steps:
Step 1
# cd /cdrom/cdrom0/saip_2.0_u1/Solaris_2.6/Packages# pkgadd -d .The following screen is displayed along with copyright and trademark information:
The following packages are available:1 SUNWsaip Serial Asynchronous Interface Driver (PCI)(sparc) 2.0,REV=1998.10.192 SUNWsaipu Serial Asynchronous Interface Utilities (PCI)(sparc) 2.0,REV=1998.10.19Select package(s) you wish to process (or 'all' to processall packages). (default:all) [?,??,q]:Step 2
Processing package instance <SUNWsaip> from</cdrom/sun_saip/saip_2.0_u1/Solaris_7/Packages>Serial Asynchronous Interface Driver (PCI)(sparc) 2.0,REV=1998.10.19Copyright 1998 Sun Microsystems, Inc. All rights reserved.Using </> as the package base directory.## Processing package information.## Processing system information.9 package pathnames are already properly installed.## Verifying package dependencies.## Verifying disk space requirements.## Checking for conflicts with packages already installed.## Checking for setuid/setgid programs.This package contains scripts which will be executed with super-userpermission during the process of installing this package.Do you want to continue with the installation of <SUNWsaip> [y,n,?] yStep 3
Installing Serial Asynchronous Interface Driver (PCI) as <SUNWsaip>## Installing part 1 of 1./etc/init.d/saip/etc/opt/SUNWconn/bin/saipconfig <symbolic link>/etc/opt/SUNWconn/bin/saipd <symbolic link>/etc/opt/SUNWconn/saip/bin/saipconfig...Installation of <SUNWsaipu> was successful.The following packages are available:1 SUNWsaip Serial Asynchronous Interface Driver (PCI)(sparc) 2.0,REV=1998.10.192 SUNWsaipu Serial Asynchronous Interface Utilities (PCI)(sparc) 2.0,REV=1998.10.19Select package(s) you wish to process (or 'all' to processall packages). (default:all) [?,??,q]:qStep 4
Step 5
# cd /# ejectStep 6
# reboot -- -rTo add an optional second Ethernet interface, continue to the "Configuring a Second Ethernet Interface" section.
If you have a second disk drive to configure, also see the "Configuring a Second Disk Drive" section.
If neither of these cases apply to your installation, continue with the next step in your chosen upgrade procedure in Chapter 1, "Solution-Level Upgrade Procedures."
If you have questions or need assistance, see the "Obtaining Technical Assistance" section on page xviii.
Configuring a Second Ethernet Interface
A second Ethernet interface is optional to the base configuration. The second interface must be configured separately by following the steps below:
Step 1
Step 2
Step 3
Step 4
Step 5
# reboot -- -rStep 6
Step 7
# ifconfig -aVerify that the new interface, hme1, appears in the output text that looks similar to the following:
Note
lo0: flags=849<UP,LOOPBACK,RUNNING,MULTICAST> mtu 8232inet 127.0.0.1 netmask ff000000hme0: flags=863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST> mtu 1500inet 172.24.235.53 netmask ffffff00 broadcast 172.24.235.255ether 8:0:20:9a:76:6chme1: flags=863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST> mtu 1500inet 172.24.237.53 netmask ffffff00 broadcast 172.24.237.255ether 8:0:20:9a:76:6cThis completes the configuration of a second Ethernet interface.
If you have a second disk drive to configure, see the "Configuring a Second Disk Drive" section. Otherwise, continue with the next step in your upgrade procedure in Chapter 1, "Solution-Level Upgrade Procedures."
If you have questions or need assistance, see the "Obtaining Technical Assistance" section on page xviii.
Configuring a Second Disk Drive
•
•
Installing the Volume Manager
Note
This section provides instructions for installing the Sun Enterprise Volume Manager 2.6 software, configuring the hard disk drives, and mirroring the operating system. Disk mirroring increases the availability of your system and prevents data loss. You can off load log and spool tasks to the second disk.
Caution
Use the second disk drive either for mirroring the first disk drive only, or for log and spool file systems only; do not use it for both.
This section contains the following procedures:
•
•
•
Installing the Sun StorEdge Volume Manager
To install the Sun StorEdge Volume Manager software and patch, complete the following steps:
Step 1
Step 2
Step 3
pkgadd -d cdrom/cdrom0/solaris_patches/CSCOh006.pkgThe following text appears:
The following packages are available:1 CSCOh006 Virtual Switch Controller Volume Manager 2.6 package installation and patches(sparc) TJB_ELAN_2000_01_04_23_16_GMTSelect package(s) you wish to process (or 'all' to processall packages). (default: all) [?,??,q]:Step 4
Processing package instance <CSCOh006> from </var/tmp/CSCOh006.pkg>Virtual Switch Controller Volume Manager 2.6 package installation and patches(sparc) TJB_ELAN_2000_01_04_23_16_GMTCisco System, Inc.The selected base directory </opt/sun_install> must exist beforeinstallation is attempted.Do you want this directory created now [y,n,?,q]Step 5
Using </opt/sun_install> as the package base directory.## Processing package information.## Processing system information.1 package pathname is already properly installed.## Verifying disk space requirements.## Checking for conflicts with packages already installed.The following files are already installed on the system and are beingused by another package:* /opt/sun_install <attribute change only>* - conflict with a file which does not belong to any package.Do you want to install these conflicting files [y,n,?,q]Step 6
## Checking for setuid/setgid programs.This package contains scripts which will be executed with super-userpermission during the process of installing this package.Do you want to continue with the installation of <CSCOh006> [y,n,?]Step 7
Installing Virtual Switch Controller Volume Manager 2.6 package installation and patches as <CSCOh006>## Executing preinstall script.Platform is SUNW,Ultra-80NOTICE: Architecture checks passed## Installing part 1 of 1./opt/sun_install/installVM/opt/sun_install/install_rootdg/opt/sun_install/install_vscdg/opt/sun_install/removeVM/opt/sun_install/remove_rootdg/opt/sun_install/remove_vscdg/var/tmp/106606-02.tar.Z[ verifying class <none> ]## Executing postinstall script.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!! You must now change directories to /opt/sun_install and !!!! run the installVM script as root. !!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Installation of <CSCOh006> was successful.Step 8
# ./installVMThe CD-ROM is ejected from the machine. The following text appears:
Install the "Sun StorEdge Volume Manager 2.6 Software" CD into the CD-ROM driverPress Enter when readyStep 9
Step 10
Sun StorEdge Volume Manager(sparc) 2.6,REV=2.5.3Copyright 1998 Sun Microsystems, Inc. All rights reserved.Copyright (c) 1990-1997 VERITAS Software Corporation.ALL RIGHTS RESERVED.THIS SOFTWARE IS THE PROPERTY OF AND IS LICENSED BY VERITAS SOFTWARE,AND/OR ITS SUPPLIERS.## Processing package information.## Processing system information.10 package pathnames are already properly installed.## Verifying package dependencies.## Verifying disk space requirements.## Checking for conflicts with packages already installed.The following files are already installed on the system and are beingused by another package:/etc <attribute change only>Do you want to install these conflicting files [y,n,?,q]Step 11
## Checking for setuid/setgid programs.The following files are being installed with setuid and/or setgidpermissions:/usr/sbin/vxprint <setuid root>Do you want to install these as setuid/setgid files [y,n,?,q]Step 12
This package contains scripts which will be executed with super-userpermission during the process of installing this package.Do you want to continue with the installation of <SUNWvxvm> [y,n,?]Step 13
Copyright (c) 1990-1997 VERITAS Software Corporation.ALL RIGHTS RESERVED.THIS SOFTWARE IS THE PROPERTY OF AND IS LICENSED BY VERITAS SOFTWARE,AND/OR ITS SUPPLIERS.Using </opt> as the package base directory.## Processing package information.## Processing system information.## Verifying package dependencies.## Verifying disk space requirements.## Checking for conflicts with packages already installed.## Checking for setuid/setgid programs.This package contains scripts which will be executed with super-userpermission during the process of installing this package.Do you want to continue with the installation of <SUNWvxva> [y,n,?]Step 14
Installation of <SUNWvmman> was successful.Ejecting CDROMChanged to /var/tmp directoryUncompressing 106606-02 ...Extracting 106606-02 ...Extraction of patch 106606-02 successfulInstalling 106606-02 ...Create vxassist fileCreate vxaltstale fileEdit S95vxvm-recover script!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! The system must be rebooted before running 'vxinstall' !!!! as root to continue the Volume Manager installation. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Do you want to reboot now (y/n)?Step 15
REBOOTING#INIT: New run level: 6The system is coming down. Please wait.System services are now being stopped.Print services stopped.Stopping the syslog service.syslogd: going down on signal 15Jan 6 12:56:21 snmpdx: received signal 15The system is down.This completes installation of the Sun StorEdge Volume Manager software and patch. Continue to the "License Key Entry and Boot Disk Encapsulation" section.
License Key Entry and Boot Disk Encapsulation
Note
Step 1
Step 2
# vxinstallThe following notice appears:
VxVM uses license keys to control access. If you have a SPARCstorageArray (SSA) controller or a Sun Enterprise Network Array (SENA) controllerattached to your system, then VxVM will grant you a limited use licenseautomatically. The SSA and/or SENA license grants you unrestricted useof disks attached to an SSA or SENA controller, but disallows stripingand RAID-5 on non-SSA and non-SENA disks. If you are not running aSPARCstorage Array controller, or a Sun Enterprise Network Array controller, then you must obtain a license key to operate.Licensing information:System host ID: 80c4d518Host type: SUNW,Ultra-80SPARCstorage Array or Sun Enterprise Network Array: No arrays found (license is required)Are you prepared to enter a license key [y,n,q,?] (default: y)Step 3
Please enter your key:Step 4
vrts:vxlicense: INFO: Feature name: CURRSET [95]vrts:vxlicense: INFO: Number of licenses: 1 (non-floating)vrts:vxlicense: INFO: Expiration date: Sun Jun 04 04:00:00 2006 (2340.6 days from now)vrts:vxlicense: INFO: Release Level: 20vrts:vxlicense: INFO: Machine Class: Allvrts:vxlicense: INFO: Key successfully installed in /etc/vx/elm/95.Do you wish to enter another license key [y,n,q,?] (default: n)Step 5
Volume Manager InstallationMenu: VolumeManager/InstallThe Volume Manager names disks on your system using the controllerand disk number of the disk, substituting them into the followingpattern:c<controller>t<disk>d<disk>If the Multipathing driver is installed on the system then for thedisk devices with multiple access paths, the controller numberrepresents a multipath pseudo controller number. For example, if adisk has 2 paths from controllers c0 and c1, then the Volume Managerdisplays only one of them such as c0 to represent both thecontrollers.Some examples would be:c0t0d0 - first controller, first target, first diskc1t0d0 - second controller, first target, first diskc1t1d0 - second controller, second target, first diskThe Volume Manager has detected the following controllers on your system:c0:Hit RETURN to continue.Step 6
Volume Manager InstallationMenu: VolumeManager/InstallYou will now be asked if you wish to use Quick Installation orCustom Installation. Custom Installation allows you to select howthe Volume Manager will handle the installation of each diskattached to your system.Quick Installation examines each disk attached to your system andattempts to create volumes to cover all disk partitions that mightbe used for file systems or for other similar purposes.If you do not wish to use some disks with the Volume Manager, or ifyou wish to reinitialize some disks, use the Custom Installationoption Otherwise, we suggest that you use the Quick Installationoption.Hit RETURN to continue.Step 7
Volume Manager Installation OptionsMenu: VolumeManager/Install1 Quick Installation2 Custom Installation? Display help about menu?? Display help about the menuing systemq Exit from menusSelect an operation to perform:Step 8
Volume Manager Custom InstallationMenu: VolumeManager/Install/CustomThe c0t0d0 disk is your Boot Disk. You can not add it as a newdisk. If you encapsulate it, you will make your root filesystemand other system areas on the Boot Disk into volumes. This isrequired if you wish to mirror your root filesystem or systemswap area.Encapsulate Boot Disk [y,n,q,?] (default: n)Step 9
Enter disk name for c0t0d0 [<name>,q,?] (default: rootdisk)Step 10
The c0t0d0 disk has been configured for encapsulation.Hit RETURN to continue.Step 11
Volume Manager Custom InstallationMenu: VolumeManager/Install/Custom/c0Generating list of attached disks on c0....<excluding root disk c0t0d0The Volume Manager has detected the following disks on controller c0:c0t1d0Hit RETURN to continue.Step 12
Installation options for controller c0Menu: VolumeManager/Install/Custom/c01 Install all disks as pre-existing disks. (encapsulate)2 Install all disks as new disks. (discards data on disks!)3 Install one disk at a time.4 Leave these disks alone.? Display help about menu?? Display help about the menuing systemq Exit from menusSelect an operation to perform:Step 13
Volume Manager Custom InstallationMenu: VolumeManager/Install/CustomThe following is a summary of your choices.c0t0d0 EncapsulateIs this correct [y,n,q,?] (default: y)Step 14
The system now must be shut down and rebooted in order to continuethe reconfiguration.Shutdown and reboot now [y,n,q,?] (default: n)Step 15
Step 16
This completes license key entry and boot disk encapsulation. Continue to the "Mirroring the Boot Disk" section.
Mirroring the Boot Disk
Step 1
# cd /opt/sun_install# ./install_rootdg
Note
# cd /opt/sun_install# ./install_rootdgThe following is displayed.Determine the device names for the disksPlatform is SUNW,Ultra-60A-DSK0: c0t0d0B-DSK0: c0t1d0Initialize device c0t1d0SucceededAdd rootdiskb to rootdg, device is c0t1d0SucceededMirror all the volumes of A-DSK0 to B-DKS0 and make rootbootableMirroring root to rootdiskbSuccessMirroring var to rootdiskbSuccessMirroring opt to rootdiskbSuccessMirroring swap to rootdiskbSuccessMirroring usr to rootdiskbSuccessStep 2
# init 6
Note
>>WARNING: forceload of drv/scsi failed
>>WARNING: forceload of drv/ssd failed
>>WARNING: forceload of drv/sf failed
>>WARNING: forceload of drv/pln failed
>>WARNING: forceload of drv/soc failed
>>WARNING: forceload of drv/socal failed
This completes configuration of a second disk drive to use for disk mirroring.
If you use this second disk drive to hold log file and spool file systems, proceed to the "Installing Log and Spool File Systems" section. Otherwise, continue with the next step in your upgrade procedure in Chapter 1, "Solution-Level Upgrade Procedures."
If you have questions or need assistance, see the "Obtaining Technical Assistance" section on page xviii.
Installing Log and Spool File Systems
Note
Installing log file and spool file systems is accomplished by performing the following steps:
Step 1
Step 2
pkgadd -d cdrom/cdrom0/solaris_patches/CSCOh005.pkgThe following text appears:
The following packages are available:1 CSCOh005 Media Gateway Controller VSC log and spool package(sparc) TJB_ELAN_1999_10_28_20_36_GMTSelect package(s) you wish to process (or 'all' to processall packages). (default: all) [?,??,q]:Step 3
Processing package instance <CSCOh005 from </var/tmp/CSCOh005.pkgMedia Gateway Controller VSC log and spool package(sparc) TJB_ELAN_1999_10_28_20_36_GMTCisco System, Inc.Using </opt/sun_install as the package base directory.## Processing package information.## Processing system information.1 package pathname is already properly installed.## Verifying disk space requirements.## Checking for conflicts with packages already installed.## Checking for setuid/setgid programs.This package contains scripts which will be executed with super-userpermission during the process of installing this package.Do you want to continue with the installation of <CSCOh005 [y,n,?]Step 4
Installing Media Gateway Controller VSC log and spool package as<CSCOh005>## Executing preinstall script.Platform is SUNW,Ultra-60NOTICE: Architecture checks passed## Installing part 1 of 1./opt/sun_install/format_log_spool.cmd/opt/sun_install/install_log_spool[ verifying class <none ]## Executing postinstall script.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!! You must now change directories to /opt/sun_install and !!!! run the install_log_spool script as root. !!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Installation of <CSCOh005> was successful.Step 5
#prompt and pressing Enter:# cd /opt/sun_install# ./install_log_spoolThe following text appears:
Build partition table for c0t1d0 ...Searching for disks...doneselecting c0t1d0...Adding entries to /etc/vfstabMounting /opt/CiscoMGC/var/logMounting /opt/CiscoMGC/var/spoolSuccess!!!
Where to Go Next
This completes the operating system installation. For more information about installing the Sun Solaris 2.6 operating system software and patches, refer to the Sun documentation that shipped with the product.
Continue with the next step in your chosen upgrade procedure in Chapter 1, "Solution-Level Upgrade Procedures."
Posted: Wed Oct 20 13:27:55 PDT 2004
All contents are Copyright © 1992--2004 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
