cc/td/doc/product/wanbu/bpx8600/9_3_3
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table Of Contents

BPX Switch Physical Overview

BPX Switch Enclosure

Node Cooling

Node DC Powering

Optional AC Power Supply Assembly

Card Shelf Configuration

BPX Switch Major Hardware Component Groups

Service Expansion Shelf PNNI

Optional Peripherals


BPX Switch Physical Overview


This chapter describes the physical components of the BPX switch.

Contents of this chapter include:

BPX Switch Enclosure

Card Shelf Configuration

BPX Switch Major Hardware Component Groups

Service Expansion Shelf PNNI

Optional Peripherals

The BPX switch is supplied as a stand-alone assembly. It may be utilized as a stand-alone ATM switch, or it may be integrated at customer sites with one or more multiband IGX switches, MGX 8220 or MGX 8800 shelves, SES PNNI shelves, and other access devices to provide network access to broadband backbone network links for narrowband traffic. Cisco and CPE service interface equipment can also be collocated with the BPX switch and connect to its ATM service interfaces.

BPX Switch Enclosure

The BPX switch enclosure is a self-contained chassis, which may be rack mounted in any standard
19-inch rack or enclosure with adequate ventilation. It contains a single shelf that provides fifteen slots for vertically mounting the BPX switch cards front and rear.

At the front of the enclosure (see Figure 2-1) are 15 slots for mounting the BPX switch front cards. Once inserted, the cards are locked in place by the air intake grille at the bottom of the enclosure.

To remove or insert cards, a mechanical latch on the air intake grille must be released by using a screwdriver and the grille must be tilted forward in order.

At the rear of the enclosure (see Figure 2-2) is another series of card slots for mounting the rear plug-in cards. These are held in place with two thumbscrews, top and bottom. A mid-plane, located between the two sets of plug-in cards, is used for interconnect and is visible only when the cards are removed.


Warning To provide proper cooling, it is essential that blank faceplates be installed in all unused slots. Failure to do so will degrade node cooling and circuit card damage will result. The blank faceplates also provide RFI shielding.


Figure 2-1 BPX Switch Exterior Front View

Node Cooling

A fan assembly with three six-inch 48 VDC fans is mounted on a tray at the rear of the BPX switch shelf (see Figure 2-2). Air for cooling the cards is drawn through an air intake grille located at the bottom in the front of the enclosure. Air passes up between the vertically-mounted cards and exhausts at the top, rear of the chassis.

All unused slots in the front are filled with blank faceplates to channel airflow properly.

Figure 2-2 BPX Switch Exterior Rear View

Node DC Powering

The primary power for a BPX switch node is -48 VDC, which is bused across the backplane for use by all card slots. DC-to-DC converters on each card convert the -48V to lower voltages for use by the card.

The -48 VDC input connects directly to the DC Power Entry Module (PEM). The DC Power Entry Module (see Figure 2-3) provides a circuit breaker and line filter for the DC input.

Nodes may be equipped with either a single PEM or dual PEMs for redundancy. PEMs are mounted at the back of the node below the backplane. A conduit hookup box or an insulated cover plate is provided for terminating conduit or wire at the DC power input. It is recommended that the source of DC for the node be redundant and separately fused.

Figure 2-3 DC Power Entry Module Shown with Conduit Box Removed

Optional AC Power Supply Assembly

For applications requiring operation from an AC power source, an optional AC Power Supply Assembly and shelf is available. It provides a source of -48 VDC from 208/240 VAC input. A shelf, separate from the BPX switch shelf, houses one or two AC Power Supplies and mounts directly below the node cabinet. This provides a secure enclosure for the power supply assemblies (supplies cannot be removed without the use of tools).

Two of these supplies are usually operated in parallel for fail-safe redundant operation. The front of the AC Power Supplies for the BPX switch includes two green LEDs to indicate correct range of the AC input and the DC output for each individual supply (see Figure 2-4).

Figure 2-4 AC Power Supply Assembly Front View

Card Shelf Configuration

There are fifteen vertical slots in the front of the BPX switch enclosure to hold plug-in cards
(see
Figure 2-5).

The middle two slots, slots number 7 and number 8, are used for the primary and secondary

Broadband Controller Cards (BCC).

The right-most slot, number 15, is used to hold the single Alarm/Status Monitor Card.

The other twelve slots, number 1 through number 6 and number 8 through number 14, can be used for the Network Interface and Service Interface cards.

Figure 2-5 BPX Switch Card Shelf Front View

BPX Switch Major Hardware Component Groups

The following are the four major groups of hardware components in the BPX switch:

Common Core Components

Network Interface Components

Service Interface Components

Power Supply Components

Table 2-1 lists these groups and their components along with a brief description of each.

Table 2-1 BPX Switch Plug-In Card Summary 

Card
Card Name
Location
Common Core Component Group

BPX-

BPX-BCC-32

Broadband Controller Card, operates with versions of System Software Release 7.0 and above, and requires 32 Mbyte RAM for 8.1 and later software. For redundancy configuration, installed as a pair of BCC-32s. (System operation equivalent to BCC-3.)

Front

BPX-BCC-bc

Back card (also known as LM-BCC) used only with the BCC-32.

Back

BPX-BCC-3-64

Broadband Controller Card, enhanced BCC-3.

Note BCC-3-64 or BCC-4 is required to support VSI and MPLS.

 

BPX-BCC-4

Broadband Controller Card, operates with 8.4 software and above. For redundancy configuration, installed as a pair of BCC-4s. Provides 64 Mbyte of RAM and above. Supports up to 19.2 Gbps performance of BXM cards.

Note BCC-3-64 or BCC-4 is required to support VSI and MPLS

Front

BPX-BCC-3-bc

Back card (also known as LM-BCC) used with BCC-4.

Back

BPX-ASM

Alarm/Status Monitor Card.

Front

BPX-ASM-BC

Line Module - Alarm/Status Monitor.

Back

Network Interface Component Group

BPX-BXM-T3-8 BPX-BXM-E3-8 BP:X-BXM-T3-12 BPX-BXM-E3-12

T3/E3 card with 8 or 12 ports. Card is configured for use in either network interface or service access (UNI) mode and with either a T3 or E3 interface.

Front

BPX-T3/E3-BC

Back card for use with a BXM-T3/E3-8 or BXM-T3/E3-12

Back

BPX-BXM-155-4 BPX-BXM-155-8

BXM OC-3 cards with 4 or 8 OC-3/STM-1ports, respectively. Card is configured for use in either network interface or service access (UNI) mode.

Front

BPX-MMF-155-4-BC BPX-SMF-155-4-BC BPX-SMFLR-155-4-BC

Back cards for BXM-155-4.

Back

BPX-MMF-155-8-BC BPX-SMF-155-8-BC BPX-SMFLR-155-8-BC

Back cards for BXM-155-8.

Back

BPX-BXM-622 BPX-BXM-622-2

OC-12 card with 1or 2 OC-12/STM-4 ports. Card is configured for use in either network interface or service access (UNI) mode.

Front

BPX-BME

Used for multicast connections. Used with SMF-622-2 back card with port 1 looped to port 2, transmit to receive, and receive to transmit.

 

BPX-SMF-622 BPX-SMFLR-622 BPX-XLR-622-BC

Back cards for BXM-622. The XLR card supports a 1500nm interface.

Back

BPX-SMF-622-2-BC BPX-SMFLR-622-2-BC BPX-SMFLR-622-2-BC

Back cards for BXM-622-2 and BME (BME typically would use SMF-622-2).

Back

BPX-BME

Used for multicast connections. Used with SMF-622-2 back card with port 1 looped to port 2, transmit to receive, and receive to transmit.

Back

BPX-BNI-3-T3

Broadband Network Interface Card (with 3 T3 Ports).

Front

BPX-T3-BC

Line Module, used with BNI-T3 for 3 physical T3 ports. (Configured for 3 ports)

Back

BPX-BNI-3-E3

Broadband Network Interface Card (with 3 E3 Ports).

Front

BPX-E3-BC

Line Module, used with BNI-E3 for 3 physical E3 ports. (Configured for 3 ports).

Back

APS Back Cards and APS Redundant Backplane

The APS 1+1 feature requires two BXM front cards, an APS redundant frame assembly, and two redundant type BXM back cards. The following are the types of redundant back card and backplane sets:

BPX-RDNT-LR-155-8 (8 port, long reach, SMF, SC connector)

BPX-RDNT-LR-622 (single port, long reach, SMF, FC connector)

BPX-RDNT-SM-155-4 (4 port, medium reach, SMF, SC connector)

BPX-RDNT-SM-155-8 (8 port, medium reach, SMF, SC connector)

BPX-RDNT-SM-622 (single port, medium reach, SMF, FC connector)

BPX-RDNT-SM-622-2 (2 port, medium reach, SMF, FC connector)

Each of the listed model numbers includes two single back cards and one mini-backplane.

Service Interface Component Group

BPX-E3-BC

Line Module, used with BNI-E3 for 2 physical E3 ports. (Configured for 2 ports)

Back

Power Supply Group
 

48 Volt DC Power Supply

 
 

Optional AC Power Supply

 

Service Expansion Shelf PNNI

The Cisco BPX SES PNNI Controller is an optional Service Expansion Shelf (SES) controller connected directly to a BPX 8600 series switch to provide Private Network to Network Interface (PNNI) signaling and routing for the establishment of ATM switched virtual circuits (SVCs) and Soft Permanent Virtual Circuits (SPVCs) over a BPX 8600 wide area network. However, the SES can be used in several WAN switching applications and is not limited to function only as a BPX SES PNNI Controller.

Every BPX 8600 series switch that deploys PNNI signaling and routing is collocated and attached to a BPX SES PNNI Controller. The BPX SES PNNI Controller uses the Cisco Virtual Switch Interface (VSI) protocol to control the BPX switch for the networking application.

The BPX SES PNNI Controller is a 7-slot chassis that contains two Processor Switch Modules (PXMs), which run the PNNI and SVC software. One of the PXMs serves as the active processor, while the other serves as the standby. The PNNI controller is mounted directly atop the BPX switch and cabled to it through either the OC-3 ATM interface (see Figure 1-3) or the DS3 interfaces (see Figure 1-4).

For instructions on installing a Service Expansion Shelf in a BPX 8620 rack and initially powering up, refer to the Cisco Service Expansion Shelf (SES) Hardware Installation Guide. To configure an SES PNNI for a BPX 8620, refer to the Cisco SES PNNI Controller Software Configuration Guide.

Optional Peripherals

At least one node in the network (or network domain if a structured network) must include a Cisco WAN Manager network management station (see Figure 2-6).

A Y-cable may be used to connect the LAN ports on the primary and secondary BCC Line Modules, through an AUI to the LAN network, because only one BCC is active at a time.

The serial control port may be connected to a dial-in modem for remote service support or other dial-up network management access. The serial auxiliary port can be used for incoming and outgoing data as well as the Autodial feature to report alarms to Cisco TAC.

Figure 2-6 Optional Peripherals Connected to BPX Switch


hometocprevnextglossaryfeedbacksearchhelp

Posted: Tue May 10 21:06:11 PDT 2005
All contents are Copyright © 1992--2005 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.