cc/td/doc/product/wanbu/bpx8600/8_5
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Setting Up Trunks

Setting Up Trunks


This chapter describes the commands related to trunks. The contents in this chapter are as follows:

Introduction

After node configuration, the trunks have to be activated. Trunks are intra-node communication links in a network. A trunk can connect any combination of IPX, IGX, or BPX nodes. Trunk characteristics are:

· Physical line type:

T1 (including fractional), E1 (including fractional), Subrate, E3, T3, or OC3 (STM1).

· Communication technology:

Asynchronous Transfer Mode (ATM) or FastPackets.

Table 4-1 shows the communication technology for each node type, card combination, and line type.


Table 4-1: Trunk Card Sets and Line Types
Node Type Front Card Back Card Line Types Technology

IPX

NTC

BC-T1

T1, T1 Fractional

FastPacket

IGX

NTM

BC-T1

T1, T1 Fractional

FastPacket

IPX

NTC

BC-E1

E1, E1 Fractional

FastPacket

IGX

NTM

BC-E1

E1, E1 Fractional

FastPacket

IPX

NTC

BC-SR

Subrate

FastPacket

IGX

NTM

BC-SR

Subrate

FastPacket

IPX

NTM

BC-Y1

Y1

FastPacket

IGX

NTM

BC-Y1

Y1

FastPacket

IPX

AIT

BC-T3, BC-E3

T3, E3

ATM

IGX

ALM/B

BC-UAI-1T3, BC-UAI-1E3

T3, E3

ATM

IGX

BTM

AIT-T3, AIT-E3, AIT-E2, AIT-HSSI, BTI-E1

T3, E3, E2, E1, HSSI

ATM

BPX

BNI

LM-3T3, LM-3E3

T3, E3

ATM

BPX

BNI-155,
BNI-155E

2OC3-SMF or
2OC3-MMF

OC3 (STM1)

ATM

BPX

BXM-155-8

MMF-155-8
SMF-155-8
SMFLR-155-8

OC3 (STM1)

ATM

BPX

BXM-155-4

MMF-155-4
SMF-155-4
SMFLR-155-4

OC3 (STM1)

ATM

BPX

BXM-622-2

SMF-622-2
SMFLR-622-2

OC12 (STM4)

ATM

BPX

BXM-622

SMF-622
SMFLR-622

OC12 (STM4)

ATM

Setting Up a Trunk

Prior to executing the commands in this section, node setup must be complete (see the chapter titled "Setting Up Nodes"). Also, the front and back cards that support the proposed line type and communication technology must reside in the slot intended for the trunk.

    1. Use the uptrk command to up the trunk. This command activates the card so it can begin generating framing. It also determines whether the trunk is physical-only or a virtual trunk. The third place digit signals that the trunk is virtual.

  Each node can have a combined maximum of 32 virtual and physical trunks. The BNI-T3 or E3 can support up to 32 virtual trunks on 1 or both physical ports. A BNI-OC3 line can support up to 11 virtual trunks. Note that, like regular trunks, virtual trunks can carry high-priority traffic.
  Use uptrk at each end of the trunk. When the trunk is up at only one end, the node detects the trunk as being in an alarm state (see dsptrks). Upping the trunk at both ends clears the alarm.

    2. Use the cnftrk command to override trunk default values. The cnftrk command is mandatory for virtual trunks but optional for physical trunks. For virtual trunks, the VPI must be changed to a non-0 value before execution of addtrk.

  If cnftrk is used, identical changes must take place at both ends of the trunk. To display existing trunk parameters, use the dsptrkcnf command. The configurable parameters are listed for each card type in the following table. (The possibilities are PKT for FastPackets, ATM cells, BNI if the trunk is a BNI card, or All.) Not all of these parameters apply to the BPX node. The BPX parameters are in a list that follows the table.
  Once the trunk is configured and after the trunk is added (addtrk), certain parameters can be re-specified. For example, a period of trunk usage may reveal a need to change parameters to optimize trunk usage. Refer to the forthcoming section titled "Reconfiguring a Trunk " for details.

    3. Use addtrk to add the trunk. Adding the trunk makes the trunk a usable resource, so connections can be added (addcon) for carrying traffic. Add a trunk at only one end of the trunk.

  (To add an interface shelf in a tiered network, use addshelf. See the chapter "Setting Up Nodes.")

Setting Up a Virtual Trunk

This section describes how to set up a virtual trunk using a BPX cloud. Virtual trunking is a purchased feature, so Cisco must enable it on each node you intend to use virtual trunking. Also, firmware levels on ASI and BNI cards must be current. For more information on virtual trunking, see the Cisco WAN Switching System Overview.


Step 1   Set up cables as follows: in the cloud network, physically connect an ASI port to each BNI port that is likely to carry virtual trunks.

Step 2   For each ASI port connected to a BNI virtual trunk port, use the following configuration sequence:

upln slot.port

upport slot.port

cnfport slot.port, and set the shift parameter to "N" for no shift.

Step 3   Execute addcon. In the cloud network, add a virtual path ASI connection for each end of the virtual trunk that is to be routed through the cloud. An example of the syntax for this is:

addcon joker 5.1.1.* swstorm 6.2.10.*

where 5.1 and 6.2 are ASI ports hooked up and configured for virtual trunking. DACS connections are acceptable. Note that the third number is the VPI, which must correspond to the virtual trunk VPI configured with cnftrk in step 4. The CBR/VBR parameter must also correspond to the Virtual Trunk Type of the virtual trunk. For T3, set PCR to 96000 and CDTV to 24000 for the connection so that the ASI does not drop cells. Cisco recommends these values based on testing.

Step 4   Configure BNI trunks. Take this step if the ATM cloud provider has assigned the VPC. On BNIs that connect to the cloud's ASI ports, configure the virtual trunks, as follows:

  uptrk slot.port.vtrk (If the cloud is already configured, the alarm on the virtual trunk should clear.)
   cnftrk slot.port.vtrk

When you use cnftrk, make sure the virtual trunk type and VPI correspond to the existing ASI Virtual Path connections.

  addtrk slot.port.vtrk

The parameters slot.port.vtrk on a BNI card can have the following values:

Reconfiguring a Trunk

This section describes how to change trunk parameters after the trunk has been added. After a trunk has been added, you can reconfigure some parameters without first deleting the trunk (deltrk). (See the list that follows.) All other changes to trunk parameters must follow trunk deletion. The parameters that are changeable without first deleting the trunk are:

To display the current trunk parameters, use dsptrkcnf. If you can make all the needed parameter changes without deleting the trunk, execute just cnftrk. Use cnftrk at both ends of the trunk.

To change parameters that first require trunk deletion:


Step 1   Delete the trunk by executing deltrk. Use deltrk at one end of the trunk.

Step 2   Execute cnftrk to reconfigure parameters. Use cnftrk at both ends of the trunk.

Step 3   Execute addtrk to add the trunk. Use addtrk at only one end of the trunk.

Removing a Trunk

To remove a trunk:


Step 1   Use the deltrk command to delete the trunk. If both ends of the trunk are reachable, perform this command at one end of the trunk only. Otherwise, this command must be performed at both ends. Connections using the deleted trunk that cannot be rerouted are automatically deleted.

Step 2   Use the dntrk command to down the trunk. Execute dntrk at both ends of the trunk.

Displaying or Printing Trunk Configurations

The network trunk configuration can be displayed on the screen or printed on the printer in a one step process by using any one of the following commands.

Setting Up ATM Trunk Redundancy

ATM trunk redundancy is the T3 and E3 trunk redundancy supported by the AIT, ALM/B, and BTM cards. Redundancy can exist between either an AIT card and BNI (BPX), a ALM/B and BNI, or a BTM and a BNI. Trunk redundancy cannot exist between IPX and IGX nodes. Also, virtual trunking and trunk redundancy are incompatible. Trunk redundancy uses the standard trunk cables rather than a Y-cable. (For all service card sets other than trunk cards, redundancy is managed through the Y-cable redundancy commands addyred, delyred, prtyred, and dspyred).

Trunk redundancy depends on the applicable commands, the trunk card in the adjacent slot, and the standard trunk cable. Trunk redundancy commands execute only on the IPX or IGX node. The BPX node does not require information regarding this feature. The following commands manage trunk redundancy:

Using Subrate Trunk Interface Control Templates

Subrate trunks use an Interface Control Template that specifies the configuration of an output control lead. The template defines which output lead is to be configured and whether the lead is asserted, inhibited, or follows a specified input source. A template for a subrate trunk can be configured individually or copied from the template of another subrate trunk.

Subrate trunk interface control templates are managed through the following commands.

Summary of Commands

Table 4-2 shows the full name and starting page for the description of each trunk command.


Table 4-2: List of Trunk Commands
Mnemonic Description Page

addtrk

Add trunk

4-7

addtrkred

Add trunk redundancy

4-9

cnftrk

Configure trunk

4-11

cnftrkalm

Configure trunk alarm

4-18

cnftrkict

Configure trunk interface control template

4-20

cpytrkict

Copy trunk interface control template

4-22

deltrk

Delete trunk

4-24

deltrkred

Delete trunk redundancy

4-26

dntrk

Down trunk

4-28

dspnw

Display network

4-30

dsptrkbob

Display trunk breakout box

4-32

dsptrkcnf

Display trunk configuration

4-34

dsptrkict

Display trunk interface control template

4-37

dsptrkred

Display trunk redundancy

4-39

dsptrks

Display trunks

4-41

dsptrkstats

Display trunk statistics

4-43

prtnw

Print network

4-45

prttrkict

Print trunk interface control template

4-47

prttrks

Print trunks

4-48

uptrk

Up trunk

4-49

addtrk

Adds a trunk between nodes. A trunk must be added to the network before it can carry traffic. Executing addtrk is necessary at only one of the nodes terminating the trunk. Before you add a trunk to the network, you must have activated (or "upped") the trunk at both ends by using uptrk.

A trunk must be free of major alarms before you can add it. If you use addtrk to join two networks that were previously separate, the local node verifies that all node names in both networks are unique before it adds the trunk.

You cannot add a trunk while any of the following conditions are true:

When using the addtrk command, exercise caution when adding a new node to a network or one network to another network. With these particular operations, the user IDs and passwords may be replaced by those in the other network. Consult Customer Service before performing these operations.

Full Name

Add trunk to the network

Syntax

addtrk <slot.port>[.vtrk]

Related Commands

deltrk, dsptrks, uptrk

Attributes

Privilege

1

Jobs

Yes

Log

Yes

Node

IPX, IGX, BPX

Lock

Yes

Example 1

addtrk 7

Description

Add trunk between node beta slot 7 and node alpha slot 10.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 3 1997 15:04 MST PLN Type Current Line Alarm Status Other End 7 E1/32 Clear - Line OK alpha.10 9 T1/24 Clear - Line OK gamma.10 13 T1/24 Clear - Line OK alpha.14 15 T1/24 Clear - Line OK gamma.15 20 T3/3 Major - AIT Missing - Last Command: addtrk 7 Next Command:
Table 4-3: addtrk-Parameters
Parameter Description

slot.port

Specifies the slot and port number of the trunk to add.


Table 4-4: addtrk-Optional Parameters
Parameter Description

vtrk

Specifies the virtual trunk number. The maximum on a node is 32. The maximum on a T3 or E3 line is 32. The maximum on an OC3/STM1 line is 11.

addtrkred

Configures trunk redundancy on an ATM trunk. The addtrkred command specifies a backup trunk to the primary trunk. Applicable line types are T3 and E3. The redundancy scheme requires two sets of ATM trunk cards and two standard T3 or E3 cables (not Y-cables). Note the following characteristics of trunk redundancy:

Trunk redundancy is not compatible with virtual trunking.

Full Name

Add trunk redundancy

Syntax

addtrkred <primary trunk> <secondary trunk>

Related Commands

deltrkred, dsptrkred

Attributes

Privilege

1-4

Jobs

No

Log

Yes

Node

IPX, IGX

Lock

Yes

Example 1

addtrkred 4 5

Description

Add bandwidth redundancy for the primary ATM trunk in slot 4 with backup from the ATM trunk in slot 5.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 3 1997 15:15 MST ATM Line Backup ATM Line 4 5
Last Command: addtrkred 4 5 Next Command:

Table 4-5: addtrkred-Parameters
Parameter Description

primary trunk

Specifies the slot number of the primary trunk card set.

secondary trunk

Specifies the slot number of the secondary trunk card set as backup.

cnftrk

Configures trunk parameters. A trunk has a default configuration after you activate (or "up") the trunk with the uptrk command. Beyond this default configuration, cnftrk lets you configure trunk parameters. Normally, you use cnftrk after you have upped the trunk (uptrk) but before you have added it to the network with addtrk. You must execute cnftrk at both ends of a trunk.

The section "cnftrk-Parameters" in this description shows required cnftrk parameters. Virtual trunk parameters are in the section titled "cnftrk-Optional Parameters." You can reconfigure some parameters after adding a trunk with addtrk. See the section "Reconfiguring a Trunk ."

In the display for cnftrk, the current value for each parameter appears on screen. At the command line prompt for each parameter, the current or default value appears in parentheses and stays the same if you press Return without typing any characters. Configurable parameters depend on the trunk type. For example, an NTM and BNI support different parameters. If a displayed parameter is not available for the current interface, its name appears at half-intensity, and the value field contains dashes. (Note that Clock Rate is a required parameter for only HSSI. The Clock Rate range is 4 Mbps-50.84 Mbps. The actual clock limits depend on the front card.)


Note If you specify cnftrk in a job, prompts appear for line format and line options when you create or edit the job with addjob or editjob, respectively.

Receive and Transmit Rates on Physical Trunks

The parameters RCV Trunk Rate and Transmit Trunk Rate apply to physical ATM trunks on an IPX or IGX node. On a BPX node, only Transmit Trunk Rate is available. These parameters let you configure lower rates than the maximum line rate for the trunk type. If you adjust a rate, do so at both ends of the trunk. For example, if RCV Trunk Rate on an IGX is 40,000 packets per second (pps), Transmit Trunk Rate on the far end must be 20,000 cells per second (cps). The typical relationship between pps and cps is two FastPackets for each cell.

For ATM trunks terminating on an AIT (IPX) or a BTM (IGX), make sure the receive rate is below the maximum of the T3 or E3 line rate. For these cards, the rate should be no more than 40,000 packets per second. (On an IPX node, the reason for reducing the rate is to prevent the MUXBUS from becoming overloaded. Furthermore, the rate should be even less if large numbers of T1 or E1 trunks exist on the same IPX node.) Increments for RCV Trunk Rate and Transmit Trunk Rate can be as small as 1 cell or packet per second. (Note that the node may round up or round down the value you enter.)

The default value for Transmit Trunk Rate is the maximum rate for the back card type. You can reduce this rate to any number of cells per second that is less than or equal to the physical port rate. If E3 or T2 is selected, the bandwidth is reduced from the T3 rate.

Receive and Transmit Rates on Virtual Trunks

The implementation of XMT Trunk Rate on a virtual trunk differs from the implementation on a physical trunk. On a physical trunk, XMT Trunk Rate limits the rate at which the back card physically generates cells. For a virtual trunk, XMT Trunk Rate does not limit the rate at which the back card generates cells: the line rate stays at the maximum for the line type. However, XMT Trunk Rate is the maximum transmission rate allowed on a virtual trunk.

The provider of the virtual trunk service assigns the value for XMT Trunk Rate. You must have this provider-assigned value for XMT Trunk Rate and enter it when you use cnftrk.

Subrate and Fractional Trunks

For FastPacket trunks, which the NTC and NTM front cards support, the Subrate interface and Subrate data rate fields are configurable only if the back card is a BC-SR. The interface types for a subrate trunk are V.11, X.21, V.35, and EIA/TIA-449. Set the data rate to match the subrate facility within the range 64 Kbps-1.920 Mbps.

The DS-0 map is used to define fractional E1 and T1 trunks. It consists of a repeating set of specifications in the form <x[-y[a]]>, where "x" and the optional "y" are DS-0 numbers 0-23, and the optional "a" indicates alternating. The value of "y" must be greater than the value of "x." The values of both "x" and "y" cannot be less than 0 or greater than the maximum number of DS-0s for the line type. In the DS-0 map for unframed E1, use 0-31. For framed E1, use 1-31. For 30 DS-0 E1, use 1-15, 17-31.

Full Name

Configure trunk

Syntax

cnftrk <slot.port>[.vtrk] <options for E1 | T1 | E3 | T3 | OC3 | OC12 | E2 | HSSI | SR >

Related Commands

addtrk, dsptrkcnf

Attributes

Privilege

1

Jobs

Yes

Log

Yes

Node

IPX, IGX, BPX

Lock

Yes

Example 1

cnftrk 11

Description

Configure trunk 11. The trunk in slot 11 is an ATM T3 trunk on an ALM/B. (If you want to verify the card is the trunk version of the ALM, use either dspcd or dspcds and check the front card "Rev." The Rev column contains a B for the first character for an ALM/B.)

System Response
IGX16 TN SuperUser IGX 16 8.5 Sep. 5 1997 16:38 PST PLN 11 Config T3/576 [192000pps] ALM slot: 11 Clock Rate: -- Idle code: 7F hex Transmit Trunk Rate: 96000 cps Restrict PCC traffic: No Rcv Trunk Rate: 192000 pps Link type: Terrestrial Subrate interface: -- Line framing: -- Subrate data rate: -- coding: -- Line DS-0 map: -- CRC: -- Pass sync: Yes recv impedance: -- Loop clock: No cable type: Statistical Reserve: 992 pps length: 0-225 ft. Header Type: STI HCS Masking: Yes Gateway Type: BAM Payload Scramble: No VPI Address: 0 End supp BData: Yes VCI Address: 0 End supp FST: Yes Last Command: cnftrk 11 Next Command:
Example 2

cnftrk 1.1

Description

Configure trunk 1.1. This trunk is an ATM T3 trunk on a BPX node.

System Response
batman TN SuperUser BPX 15 8.5 Date/Time Not Set TRK 1.1 Config T3 [96000 cps] BNI-T3 slot: 1 Restrict CC traffic: No Transmit Rate: 96000 Link type: Terrestrial Subrate interface: -- Line framing: -- Subrate data rate: -- coding: -- Line DS-0 map: -- CRC: -- Pass sync: Yes recv impedance: -- Loop clock: No cable type: Statistical Reserve: 992 cps length: 0-225 ft. Idle code: 7F hex HCS Masking: Yes Connection Channels: 1771 Payload Scramble: No Valid Traffic Classes: Frame Scramble: -- V,TS,NTS,FR,FST,CBR,VBR,ABR Virtual Trunk Type: -- SVC Channels: 0 Virtual Trunk VPI: -- SVC Bandwidth: 0 cps Virtual Trunk Service: -- This Command: cnftrk 1.1 Transmit Rate [T2=14490, E3=80000, T3=96000, OC3 = 353208](96000):
Example 3

cnftrk 13.1.1

Description

Configure trunk 13.1.1 (a virtual trunk on an ATM T3).

System Response
sw97 TN SuperUser BPX 15 8.5 July 30 1997 11:45 GMT TRK 13.1.1 Config T3 [2867 cps] BNI-T3 slot: 13 Restrict CC traffic: No Transmit Rate: 3000 Link type: Terrestrial Subrate interface: -- Line framing: -- Subrate data rate: -- coding: -- Line DS-0 map: -- CRC: -- Pass sync: No recv impedance: -- Loop clock: No cable type: Statistical Reserve: 992 cps length: 0-225 ft. Idle code: 7F hex HCS Masking: Yes Connection Channels: 55 Payload Scramble: No Valid Traffic Classes: Frame Scramble: -- V,TS,NTS,FR,FST,CBR,VBR,ABR Virtual Trunk Type: CBR Virtual Trunk VPI: 0 Virtual Trunk Service: 4 Last Command: cnftrk 13.1.1 3000 N N 992 7F 55 V,TS,NTS,FR,FST,CBR,VBR,ABR N TER RESTRIAL 0 Y N CBR 0 Next Command:
Table 4-6: cnftrk-Parameters
Trunk Option Type Description Possible Entries Default

slot.port

All

The number of the trunk to configure.

Any valid slot and port. For cards with one port, use slot.

N/A

Trunk Identification

(display only—not configurable)

All

Displays trunk number, trunk type and bandwidth supplied, and the card type and slot number of the unit supporting the trunk.

T3, E3, T1, E1, E2, fractional T1, fractional E1 subrate, ATM, NTC, NTM, OC3, STM1, OC12, STM4.

none

Clock Rate

ATM

This clock rate is for only HSSI.

4 Mbps-50.84Mbps

Rcv TRK Rate

ATM

CELLBUS or MUXBUS bandwidth in packets per second (pps) to allocate to a BTM, ALM/B, or AIT. On a BPX, Rcv TRK Rate is not used.

ALM/B T3: 1K-192K pps

BTM (IGX) or AIT (IPX): 0-80K pps

BTM-E1: 0-10538 pps for CGW, unframed E1 or
0-10208 pps for CGW, for framed E1

1000 pps

Subrate interface

PKT

Subrate physical interface type

X.21 | V.35

X.21

Subrate data rate

PKT

Subrate data rate in Kbps

64-1920 Kbps

1920 Kbps

DS0 map

PKT

Specifies the DS0s to use for a fractional T1 or E1 bundle. Optional "a" = "use alternating channels" (for example, 20-30a means 20, 22, 24, and so on.)

x - y[a]

0-31 (E1) 0-23 (T1)

Pass sync

All

Enables the trunk to pass a clock for network synchronization.

Yes | No

Yes for standard, no for virtual trunks

Loop Clock

All

Loop receive clock back to transmit.

Yes | No

No

Statistical
Reserve

All

This trunk bandwidth is reserved for non-standard traffic, such as internode controller messages or user traffic diverted because of a failure.

0-10666

600 for FastPackets
1000 for ATM cells
(992 cells on BNI)

Header Type

ATM

Selects the ATM cell header type: UNI, NNI, or STI. See the Cisco WAN Switching System Overview for a description.

UNI | NNI | STI
.

STI

Gateway Type

ATM

Defines the type of addressing mode for this trunk. See Cisco WAN Switching System Overview for a description.

BPX-BPX (BAM)
Cloud (CAM)
Simple (SAM)

BAM

VPI Address

ATM

Virtual path address in ATM cell. Must be non-0 for a virtual trunk.

0-255

0

VCI Address

ATM

Virtual circuit address in ATM cell.

0-65,535

0

Idle code

All

HEX code either in the payload space of an ATM idle cell or on an idle FastPacket trunk (idle packets do not exist)

0-FF (hex)

54 (E1)
7F (T1, ATM)

SVC Channels

ATM

The number of channels reserved for SVCs.

T3: 0-1771

E3: 0-1771

OC3: 0-16199

0

SVC Bandwidth

ATM

The bandwidth reserved for SVCs.

T3: 96000 cps

E3: 80000 cps

OC3: 353208 cps

0

Restrict CC traffic (requires super user privilege)

All

Restrict node controller messages from
a trunk. Restricting CC traffic can cause serious problems. Contact the TAC through Cisco Customer Engineering before you change it.

Y | N

No

Link type

All

Terrestrial or Satellite link.Link Type applies to configuring a route so it can "avoid satellite."

T | S

T

Line framing

PKT

T1 line framing

D4 | ESF

D4

Line coding

PKT

E1 line coding
T1 line coding

HDB3 | AMI
ZCS | B8ZS | AMI

HDB3
ZCS

Line CRC

PKT

E1 CRC-4

Yes | No

No

Recv impedance

PKT

E1 receive impedance

1 = 75W unbalanced
2 = 75W balanced
3 = 120W balanced

1

Cable type and
cable length

PKT



ATM

Length and type of cable used for trunk. Designates the software configurable line build-out to match the cable length from the IPX or IGX node to the DSX cross-connect.



For BPX, the choices are 0-225 feet and over 225 feet. Cable type is not selectable for BPX. Not applicable to MMF or SMF

1 = 0-220' MAT
2 = 220-440' MAT
3 = 440-655' MAT
4 = 0 -133' ABAM
5 = 133-266' ABAM
6 = 266-399' ABAM
7 = 399-533' ABAM
8 = 533-655' ABAM

0= 0-225
1= greater than 255

4








0

HCS Masking

ATM

Mask the ATM cell header checksum to disable error checking. HCS Masking applies to E3, OC3, and OC12 only.

Yes | No

Yes

Payload Scramble

ATM
BNI

Scramble the cell payload.

Yes | No

Yes for BNI-E3
No for all others

End supp BData

PKT
ATM

Indicates whether the far end of a trunk supports bursty, Frame Relay data.

Yes | No

No

End supp FST

PKT
ATM

Indicates whether the far end of the trunk supports ForeSight for Frame Relay.

Yes | No

No

Gateway
Efficiency

ATM

How many packets to stuff into an ATM cell. Does not apply to BNI.

1 | 2 | 3

2


Table 4-7: cnftrk-Optional Parameters
Virtual Trunk Parameter Type Description Possible Entries Default

Connection Channels

BNI

The maximum number of connection channels per trunk. All virtual trunks on the port share this total. The number of connections added to the port cannot exceed the number of connection channels configured for the port.

BNI-T3/E3: max 1771

BNI-OC3: max 15867

BNI-T3/E3: 1771

BNI-OC3: 15867

For Virtual Trunks:

BNI-T3/E3: 55

BNI-OC3: 1442

Valid Traffic Classes

BNI

The valid types of traffic for a virtual trunk. The recommended traffic classes for each virtual trunk types:

On a CBR trunk: ATM CBR, NTS, TS, voice.
On a VBR trunk: ATM VBR and bursty data A.
On an ABR trunk: ATM ABR and bursty data B (ForeSight).

V—voice
TS—timestamped
NTS—non-timestamped
FR—Frame Relay
FST—ForeSight
CBR—constant bit rate
VBR—variable bit rate
ABR—available bit rate

Virtual Trunk Type

BNI

This choice usually comes from the carrier that provides the ATM cloud.

CBR, VBR, ABR

CBR

Virtual Trunk VPI

BNI

Virtual Trunks must be configured to have a greater-than-0 VPI before connections are added by addcon. This value usually comes from the carrier that provides the ATM cloud.

1-255 for T3/E3

1-63 for OC3 (STM1)

cnftrkalm

Configures alarm reporting for a trunk. When a trunk is upped and added to the network, alarm reporting is enabled, but cnftrkalm lets you disable alarms on upped trunks. Disabling alarms can be useful when a trunk is connected to a node but not yet in service or when a trunk has occasional bursts of errors but still functions.

In an IPX or IGX node, enabled alarms cause an output from the ARC or ARM card or an indication to StrataView Plus.

Full Name

Configure trunk alarms

Syntax

cnftrkalm <slot.port>[.vtrk] <e | d>

Related Commands

dspalms, dsptrks

Attributes

Privilege

1-5

Jobs

Yes

Log

Yes

Node

IPX, IGX, BPX

Lock

Yes

Example 1

cnftrkalm 7 d

Description

Disable trunk alarms on trunk 7.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 3 1997 15:21 MST PLN Type Current Line Alarm Status Other End 7 E1/32 Clear - Line OK alpha.10 9 T1/24 Clear - Line OK gamma.10 13 T1/24 Clear - Line OK alpha.14 15 T1/24 Clear - Line OK gamma.15 20 T3/3 Major - AIT Missing - Last Command: cnftrkalm 7 d Next Command:
Table 4-8: cnftrkalm-Parameters
Parameter Description

slot.port

Specifies the trunk number.

e

Enables the alarm.

d

Disables the alarm.


Table 4-9: cnftrkalm-Optional Parameters
Parameter Description

vtrk

Specifies the virtual trunk number.

cnftrkict

Configures the output lines of an interface control template for a subrate trunk. Table 4-10 shows the configurable signals:


Table 4-10:
Interface Type Output Signal Inputs

X.21

C, I

V.35

RTS, DTR

CTS, DSR

MIL-188

IS, LL, RL, RS, SF, SS, TR

DM, CS

Configurable Signals in an Interface Control Template
Full Name

Configure trunk interface control template

Syntax

cnftrkict <line> <output> <source>

Related Commands

dsptrkict, prttrkict

Attributes

Privilege

1-2

Jobs

Yes

Log

Yes

Node

IPX, IGX

Lock

Yes

Example 1

cnftrkict 9 c on

Description

Configure output lead "c" as "on" in the interface control template for subrate trunk 9.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 3 1997 15:15 MST Packet Line: 9 Interface: X.21 DTE Interface Control Template for Trunk Line Lead Output Value Lead O Output Value C /DTR ON Last Command: cnftrkict 9 c on Next Command:
Table 4-11: cnftrkict-Parameters
Parameter Description

line

Specifies the trunk for the interface control template.

output

Specifies the output lead to be configured. Configurable output leads vary depending on the type of data interface used (X.21or V.35).

source

Specifies how the specified output lead is to be configured. The options are as follows:

  • On, which means the output lead is asserted.

  • Off, which means the output lead is inhibited.

  • l (lower case L) Output follows a local input lead.

  • Input, which specifies the name of the local input lead that the output lead follows.

Input leads vary according to the type of data interface supported (X.21 or V.35).

cpytrkict

Copies the interface control template of one trunk to another trunk. Once copied, the control information can be edited with the cnftrkict command. See the cnftrkict description for more information on configuring the trunk interface control templates.

Full Name

Copy trunk interface control template

Syntax

cpytrkict <source_trunk> <destination_trunk>

Related Commands

cnftrkict, dsptrkict

Attributes

Privilege

1-2

Jobs

Yes

Log

Yes

Node

IPX, IGX

Lock

Yes

Example 1

cpytrkict 9 11

Description

Copy the interface control template for trunk 9 to trunk 11.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 3 1997 15:15 MST Packet Line: 9 Interface: X.21 DTE Interface Control Template for Trunk Line Lead Output Value Lead Output Value C/DTR ON Last Command: cpytrkict 9 11 Enter destination line number:
Table 4-12: cpytrkict-Parameters
Parameter Description

source trunk

Specifies the trunk number of the interface control template information to be copied.

destination trunk

Specifies the trunk number to which the interface control template information is copied.

deltrk

Deletes a trunk. Because deleting a trunk removes the communication path between two nodes, using deltrk may split a network into two separate networks. If deltrk execution splits the network, deletion of the connections that were using the deleted trunk also occurs.

If both nodes on the trunk are reachable, executing deltrk is necessary on only one node. If a trunk is deleted on a node while the node at the other end is unreachable, the unreachable node does not detect the deletion, so be sure to delete the trunk at both nodes in this case.

After you delete a trunk, it still carries framing signals but no traffic. Also, the trunk can generate alarms for counting. To remove a trunk completely, use dntrk after the deltrk command.

In the following situations, the node does not allow deltrk to execute:

Full Name

Delete trunk from a network

Syntax

deltrk <slot.port>[.vtrk]

Related Commands

addtrk, dntrk, dspnw, dsptrks uptrk

Attributes

Privilege

1

Jobs

Yes

Log

Yes

Node

IPX, IGX, BPX

Lock

Yes

Example 1

deltrk 7

Description

Delete trunk 7 from the network.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 15 1997 15:02 MST PLN Type Current Line Alarm Status Other End 7 E1/32 Clear - Line OK - 9 T1/24 Clear - Line OK gamma.10 13 T1/24 Clear - Line OK alpha.14 15 T1/24 Clear - Line OK gamma.15 20 T3/3 AIT - AIT Missing - Last Command: deltrk 7 Next Command:
Table 4-13: deltrk-Parameters
Parameter Description

slot.port

Specifies the physical trunk number.


Table 4-14: deltrk-Optional Parameters
Parameter Description

vtrk

Specifies the virtual trunk portion of the trunk identifier.

deltrkred

Removes redundancy from an ALM/B, BTM, or AIT trunk. After you execute deltrkrd, you can remove the backup card without causing an alarm.

Full Name

Delete ATM trunk redundancy

Syntax

deltrkred <backup ATM trunk number>

Related Commands

addtrkred, dsptrkred

Attributes

Privilege

1-4

Jobs

No

Log

Yes

Node

IPX, IGX

Lock

Yes

Example 1

deltrkred 5

Description

Remove ATM trunk redundancy for the card set in slot 5.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 15 1997 15:15 MST ATM Line Backup ATM Line
5 8 Last Command: deltrkred 5 Next Command:

Table 4-15: deltrkred-Parameters
Parameter Description

Backup trunk number

Specifies of the ATM card set assigned as the backup.

dntrk

Downs a trunk, after which it no longer carries framing or statistics. Before you can down a trunk with dntrk, you must remove it must from the network with deltrk (or delshelf in a tiered network).

Full Name

Down trunk

Syntax

dntrk <slot.port>[.vtrk]


Note No space exists between the port number and the "." for the virtual trunk specification.
Related Commands

addtrk, deltrk, uptrk, dsptrks

Attributes

Privilege

1-2

Jobs

Yes

Log

Yes

Node

IPX, IGX, BPX

Lock

Yes

Example 1

dntrk 9

Description

Deactivate trunk 9.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 3 1997 10:53 MST From Type Current Line Alarm Status Other End 13 T1/24 Clear - Line OK alpha.14 15 T1/24 Clear - Line OK gamma.15 20 T3/3 Major - AIT Missing - Last Command: dntrk 9 Next Command:
Table 4-16: dntrk-Parameters
Parameter Description

slot.port

Specifies the physical trunk.


Table 4-17: dntrk-Optional Parameters
Parameter Description

vtrk

Specifies a virtual trunk number (applies to BNI only). T3/E3 range is 1-32. OC3 range is 1-11.

dspnw

Displays the network topology in tabular form. Alarms appear in a column, and added trunks (by addtrk) appear to the right to the node name. Each trunk entry shows the local back card slot number and the node name and back card slot number on the other end of the line. Note the following conventions:

If the network has more nodes and trunk connections than are currently on the screen, a "Continue?" prompt appears. Press the Return key to display other parameters, or enter "n" to exit the command.

Full Name

Display network

Syntax

dspnw [+b | -b] [+z | -z]

Related Commands

dspnds, prtnw

Attributes

Privilege

1-6

Jobs

No

Log

No

Node

IPX, IGX, BPX

Lock

No

Example 1

dspnw

Description

Display the network topology in tabular form.

System Response
sw91 TN SuperUser IPX 8 8.5 Nov. 13 1997 16:06 GMT NodeName Alarm Packet Line sw92 UNRCH 8-7/sw91 sw200 UNRCH 14-14/sw201 15-15/sw201 16-16/sw201 sw201 UNRCH 14-14/sw200 15-15/sw200 16-16/sw200 12.1-4.5/sw26 sw12 MAJOR 3.1.2-4.7/sw26 3.1.3-6.3/sw91 sw91 MAJOR 7-8/sw92 6.3-3.1.3/sw12 6.4-3.1.4/sw68 sw68 Minor 3.1.4-6.4/sw91 This Command: dspnw Continue?

The display shows a network containing the nodes alpha, beta, and gamma. The word "Major" on the right of "gamma" and "beta" (see Alarm column) indicates the existence of alarm conditions such as loss of signal.

The "10-9/beta" listed to the right of node gamma indicates that trunk 10 on node gamma connects to node beta as trunk 9. The "7-10/alpha" listed to the right of node beta indicates that trunk 7 on node beta connects to node alpha as trunk 10. If the two trunk numbers are separated by an tilde (~) in place of a dash (-), the display is indicating a satellite. The following illustrates a map of this network.


Table 4-18: dspnw-Optional l Parameters
Parameter Description

+b

Display only the lines that support bursty data.

-b

Display only the lines that do no support bursty data.

+z

Display only the lines that use ZCS encoding.

-z

Display only the lines that do not use ZCS encoding.

dsptrkbob

Displays the state of all inputs from subrate line equipment to an IPX or IGX node and the state of all outputs from the node to the subrate line equipment. Display updates can occur at an optional, user-specified interval. Otherwise, the display remains on-screen until Delete is pressed or the display times out. The default interval for updating the display is every 5 seconds. If a trunk is disabled, its number appears in dim, reverse video. See cnftrkict for configuration details.

Full Name

Display trunk breakout box

Syntax

dsptrkbob <line> [interval]

Related Commands

cnftrkict, dsptrkict

Attributes

Privilege

1-6

Jobs

No

Log

No

Node

IPX, IGX

Lock

Yes

Example 1

dsptrkbob 9

Description

Display the breakout for subrate trunk 9.

System Response
beta TRM YourID:1 IPX 32 8.5 Sep. 15 1997 15:15 MST Packet Line: 9 Interfaces: X.21 DTE Inputs from Line Equipment Outputs to Line Equipment Lead Pin State Lead Pin State Lead Pin State Lead Pin State
RxD 4/11 Idle TxD 2/9 Active
I/DSR 5/12 On C/DTR 3/10 On
S/RxC 6/13 Active Last Command: dsptrkbob 9 Hit DEL key to quit:

Table 4-19: dsptrkbob-Parameters
Parameter Description

trunk

Specifies the subrate trunk.


Table 4-20: dsptrkbob-Optional Parameters
Parameter Description

interval

The number of seconds between updates of the breakout box display. The range is 1-60.

dsptrkcnf

Displays trunk configuration. The parameter values that dsptrkcnf displays have been set with cnftrk or are default values.

Full Name

Display trunk configuration

Syntax

dsptrkcnf <slot.port>[.vtrk]

Related Commands

cnftrk

Attributes

Privilege

1-6

Jobs

No

Log

No

Node

IPX, IGX, BPX

Lock

No

Example 1

dsptrkcnf 6

Description

Display the configuration for trunk 6. Trunk 6 is an AIT trunk on an IPX node.

System Response
sw91 TN SuperUser IPX 8 8.5 Sep. 22 1997 16:09 GMT PLN 6 Configuration T3/3 [1000 pps] AIT slot: 6 Clock Rate: -- Idle code: 7F hex Transmit Trunk Rate: 96000 cps Restrict PCC traffic: No Rcv Trunk Rate: 1000 pps Link type: Terrestrial Subrate interface: -- Line framing: -- Subrate data rate: -- coding: -- Line DS-0 map: -- CRC: -- Pass sync: Yes recv impedance: -- Loop clock: No pps cable type: Statistical Reserve: 992 length: 0-225 ft. Header Type: STI HCS Masking: Yes Gateway Type: BAM Payload Scramble: No VPI Address: 0 End supp BData: Yes VCI Address: 0 End supp FST: Yes Last Command: dsptrkcnf 6 Next Command:
Example 2

dsptrkcnf 11

Description

Display the configuration for the E3 trunk in slot 11 (an ALM/B trunk).

System Response
IGX16 TN SuperUser IGX 16 8.5 Sep. 23 1997 02:08 GMT PLN 11 Config E3/480 [160000pps] ALM slot: 11 Clock Rate: -- Idle code: 7F hex Transmit Trunk Rate: 80000 cps Restrict PCC traffic: No Rcv Trunk Rate: 160000 pps Link type: Terrestrial Subrate interface: -- Line framing: -- Subrate data rate: -- coding: -- Line DS-0 map: -- CRC: -- Pass sync: Yes recv impedance: -- Loop clock: No cable type: Statistical Reserve: 992 pps length: 0-225 ft. Header Type: STI HCS Masking: Yes Gateway Type: BAM Payload Scramble: No VPI Address: 0 End supp BData: Yes VCI Address: 0 End supp FST: Yes Last Command: dsptrkcnf 11 Next Command:
Example 3

dsptrkcnf 13.3.1

Description

Display the configuration for virtual trunk 13.3.1. The trunk is on a BNI-T3 card set in a BPX node.

System Response
sw97 TN SuperUser BPX 15 8.5 June 22 1997 07:34 GMT TRK 13.3.1 Config T3 [2867 cps] BNI-T3 slot: 13 Restrict CC traffic: No Transmit Rate: 3000 Link type: Terrestrial Subrate interface: -- Line framing: -- Subrate data rate: -- coding: -- Line DS-0 map: -- CRC: -- Pass sync: No recv impedance: -- Loop clock: No cable type: Statistical Reserve: 992 cps length: 0-225 ft. Idle code: 7F hex HCS Masking: Yes Connection Channels: 55 Payload Scramble: No Valid Traffic Classes: Frame Scramble: -- V,TS,NTS,FR,FST,CBR,VBR,ABR Virtual Trunk Type: CBR Virtual Trunk VPI: 1 Virtual Trunk Service: 3 Last Command: dsptrkcnf 13.3.1 Next Command:
Table 4-21: dsptrkcnf-Parameters
Parameter Description

slot.port

Specifies the physical slot and port number of the trunk.


Table 4-22: dsptrkcnf-Optional Parameters
Parameter Description

vtrk

Specifies the virtual trunk number. The maximum value on a node is 32. The maximum on a T3 or E3 line is 32. The maximum for user traffic on an OC3/STM1 trunk is 11. (See also the section called "Setting Up a Virtual Trunk " at the front of this chapter.)

dsptrkict

Displays interface control information for the subrate trunks. The displayed information includes:

To see a list of configurable outputs, and information on how to configure an output, see the cnftrkict command. Disabled trunks have their trunk number displayed in dim, reverse video on the screen.

Full Name

Display trunk interface control templates

Syntax

dsptrkict <line>

Related Commands

cnftrkict, prttrkict

Attributes

Privilege

1-2

Jobs

No

Log

No

Node

IPX, IGX

Lock

No

Example 1

dsptrkict 9

Description

Display subrate for the trunk 9 interface control template.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 15 1997 15:15 MST Packet Line: 9 Interface: X.21 DTE Interface Control Template for Trunk Line Lead Output Value Lead Output Value C/DTR ON Last Command: dsptrkict 9 Next Command:

dsptrkred

Displays the backup and primary cards for a trunk.

Full Name

Display ATM trunk redundancy

Syntax

dsptrkred [trunk]

Related Commands

addtrkred, deltrkred

Attributes

Privilege

1-4

Jobs

No

Log

No

Node

IPX, IGX, BPX

Lock

No

Example 1

dsptrkred

Description

Display all ATM trunks with redundancy.

System Response
beta TRM YourID:1 IPX 32 8.5 Aug. 15 1997 15:15 MST ATM Line Backup ATM Line
4 5
7 8 Last Command: dsptrkred Next Command:

Table 4-23: dsptrkred-Optional Parameters
Parameter Description

ATM trunk number

Specifies the slot number of the primary or backup ATM card set to display. Without this optional entry, the screen displays all primary and backup ATM trunks.

dsptrks

Displays basic trunk information for all trunks on a node. This command applies to both physical only and virtual trunks. The displayed information consists of:

In addition, for trunks that have been added to the network with the addtrk command, the information includes the node name and trunk number at the other end. Trunks that have a "-" in the Other End column have been upped with uptrk but not yet added on both ends with addtrk. For disabled trunks, the trunk numbers appear in reverse video on the screen.

Full Name

Display trunks

Syntax

dsptrks

Related Commands

addtrk, deltrk, dntrk, dsptrks, uptrk

Attributes

Privilege

1-6

Jobs

No

Log

No

Node

IPX, IGX, BPX

Lock

No

Example 1

dsptrks

Description

Display information on the trunk configuration and alarm status for the trunks at a node. The trunk numbers with three places represent virtual trunks.

System Response
sw53 TN SuperUser BPX 15 8.5 Sep. 24 1997 23:03 GMT TRK Type Current Line Alarm Status Other End 1.1 T3 Clear - OK sw89(IPX/AF) 1.2 T3 Clear - OK - 1.3 T3 Clear - OK - 2.1.1 OC3 Clear - OK - 3.1 T3 Clear - OK sw92(IPX/AF) 3.2 T3 Clear - OK sw91(IPX/AF) 3.3 T3 Clear - OK sw90(IPX/AF) 4.1 T3 Clear - OK sw24(IPX/AF) 4.2 T3 Clear - OK swstorm/1.1 4.3 T3 Clear - OK sw25(IPX/AF) 13.1 T3(E3) Clear - OK - 13.2.1 T3 Clear - OK - 13.2.2 T3 Clear - OK - 13.2.3 T3 Clear - OK - Last Command: dsptrks Next Command:

dsptrkstats

Displays the trunk port status, ATM cell loss counts, cell payload errors, and cell header errors for the specified trunk. Table 4-24 lists the other statistics. If you include the optional clear parameter, dsptrkstats execution clears the statistics.


Table 4-24: Additional Statistics in the dsptrkstats Display
Statistics Description

Cells dropped due to BFrame parity err.

A parity error was detected in one or more of the P bits in the BFrame header or in the BIP-16 parity check for the header causing the cell to be dropped.

Cell header mismatch error count.

A count of cells received by a BNI in this slot.port with an incorrect header address for that card.

First mismatch cell header VPI/VCI.

This displays the VPI/VCI address of the first header mismatch to be received by the card in this slot.port.

BFrame cell data payload error.

A separate BIP-16 parity check is used for the payload data. This number represents the number of errors detected by this parity check. This does not necessarily cause a cell to be dropped.

BFrame cell loss due to admin access.

Internal to the BNI card is an administrative processor. This statistic is a count of the cells that were lost in an internal administrative shuffle.

Full Name

Display trunks statistics

Syntax

dsptrkstats <slot.port> [clear]

Related Commands

cnftrkstats, dsptrkerrs

Attributes

Privilege

1-6

Jobs

No

Log

No

Node

BPX

Lock

Yes

Example 1

dsptrkstats 1.1

Description

Display cell statistics for ATM trunk 1.1.

System Response
sw53 TN SuperUser BPX 15 8.5 Sep. 24 1997 23:07 GMT Trunk 1.1 Status: Clear - OK Cleared: 04/24/96 17:31:16 Type Count Cells dropped due to BFrame parity err 0 Cell header mismatch error count 0 BFrame cell data payload error 0 BFrame cell loss due to disabled chan 0 BFrame cell count(TX) 8316 non-hipri cells - 52 BFrame cell count(RX) 12452 First mismatch cell masked VPI/VCI 0 First mismatch cell full VPI/VCI 0 Last Command: dsptrkstats 1.1 Next Command:
Table 4-25: dsptrkstats-Parameters
Parameter Description

slot.port

Specifies the physical part of the logical trunk number.


Table 4-26: dsptrkstats-Optional Parameters
Parameter Description

clear

Directs the system to clear the statistics counters.

prtnw

Prints the network topology table. Alarms print in a column, and added trunks (by addtrk) appear to the right to the node name. Each trunk entry shows the local back card slot number and the node name and back card slot number on the other end of the line. Note the following conventions:

Parameters set Zero Coded Suppression (ZCS) display characteristics. ZCS writes a 1 over the least significant bit of any byte that contains 0s. The purpose is to ensure a minimum occurrence of 1s so that the receiving node can extract timing information. The prtnw command uses the same syntax and prints the same information as the dspnw command.

Full Name

Print network

Syntax

prtnw [+b | -b] [+z | -z]

Related Commands

dspnw

Attributes

Privilege

1-6

Jobs

Yes

Log

No

Node

IPX, IGX, BPX

Lock

Yes

Example 1

prtnw

Description

Print the network topology.

System Response

(No screen display appears—just a printout.)


Table 4-27: prtnw-Parameters
Parameter Description

+b

Display only the lines that support bursty data.

-b

Display only the lines that do no support bursty data.

+z

Display only the lines that use ZCS encoding.

-z

Display only the lines that do not use ZCS encoding.

prttrkict

Prints the interface control template of a subrate trunk. For a list of configurable outputs and configuration steps, see the cnftrkict description. The printed information includes:

Full Name

Print trunk interface control template

Syntax

prttrkict <line>

Related Commands

dsptrkict

Attributes

Privilege

1-2

Jobs

Yes

Log

No

Node

IPX, IGX

Lock

Yes

Example 1

prttrkict

Description

Print network topology.

System Response

(No screen display—just a printout.)


Table 4-28: prttrkict-Parameters
Parameter Description

line

Specifies the trunk interface control template.

prttrks

Prints the trunk configuration for the node. This command uses the same syntax and prints the same information as the dsptrks command. Configuration information for trunks includes the trunk number and the type of line (T3, E3, and so on). For trunks that have been added to the network with the addtrk command, the configuration information also includes the node name and trunk number at the other end of the line.

Note the following printout characteristics:

Full Name

Print trunks

Syntax

prttrks

Related Commands

dsptrks

Attributes

Privilege

1-6

Jobs

Yes

Log

No

Node

IPX, IGX, BPX

Lock

Yes

Example 1

prttrks

Description

Print trunk configuration for the node.

System Response

(No screen display appears—just a printout.)

uptrk

Activates (or "ups") a trunk and, if you include the optional vtrk parameter for applicable cards, activates the trunk as a virtual trunk.

After you have upped the trunk but not yet added it, the trunk carries line signalling but does not yet carry live traffic. Before you add the trunk with addtrk, the node can monitor the trunk for reliability. Once a trunk has shown reliability and is ready to go into service, add the trunk to the network. If you need to take an active trunk out of service, use dntrk. The dntrk command causes the node to reroute any existing traffic if sufficient bandwidth is available.

You cannot mix physical and virtual trunk specifications. For example, after you up a trunk as a standard trunk, you cannot add it as a virtual trunk when you execute addtrunk. Furthermore, if you want to change trunk types between standard and virtual, you must first down the trunk with dntrk then up it as the new trunk type.

You cannot up a trunk if the required card is not available. Furthermore, if a trunk is executing self-test, a "card in test" message may appear on-screen. If this message appears, re-enter uptrk.

Full Name

Up trunk

Syntax

uptrk <slot.port>[.vtrk]

Related Commands

addtrk, dntrk

Attributes

Privilege

1-2

Jobs

Yes

Log

Yes

Node

IPX, IGX, BPX

Lock

Yes

Example 1

uptrk 21

Description

Activate (up) trunk 21—a single-port card, in this case, so only the slot is necessary.

Example 2

uptrk 6.1.1

Description

Activate (up) trunk 6.1.1—a virtual trunk, in this case, which the third digit indicates.


Table 4-29: uptrk-Parameters
Parameter Description

slot.port

Specifies the slot and port of the trunk to activate. If the card has only one port, the port parameter is not necessary. An NTM, for example, has one port.


Table 4-30: uptrk-Optional Parameters
Parameter Description

vtrk

Specifies the virtual trunk number. The maximum on a node is 32. The maximum on a T3 or E3 line is 32. The maximum for user traffic on an OC3/STM1 trunk is 11 (so more than one OC3/STM1 may be necessary). See also the section called "Setting Up a Virtual Trunk " at the front of this chapter.


hometocprevnextglossaryfeedbacksearchhelp
Posted: Wed Jan 17 21:36:52 PST 2001
All contents are Copyright © 1992--2001 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.