Table of Contents

A
B
C
D
E
F
G
H
I
J
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y

Glossary

A

The bit in the frame relay frame header that indicates the status of the far end user device and the status of the PVC segment in the foreign network.

An analog to digital encoding scheme used to convert voice samples to an 8-bit data word used in CEPT E1 multiplex equipment. (See also µ-law.)

ATM connection type for bursty traffic, such as data. Provides closed loop control of service rate that allows connections to use additional bandwidth when available. ABR may be used with ATM Traffic Management 4.0 standards VSVD flow congestion control, or with the proprietary ForeSight flow congestion control. See also, CBR and VBR.

A switch to turn off the audible alarm outputs from a node while leaving the visual alarm outputs unchanged.

An optional feature of the IPX that disables VAD from connections using it whenever there is excess bandwidth available to allow the normal encoded voice to be carried on the packet line. See also VAD.

A compression method that samples voice 8,000 times per second, and uses the changes between samples as the basis for compression. Increases the capacity of a T1 line from 24 to 48 channels.

Time permitted between sending RM cells before the rate is decreased to ICR.

The AIT front card provides an ATM trunk interface for the IPX. The AIT operates in conjunction with a backcard, AIT-T3 or AIT-E3.

The AIT-E3 backcard provides an E3 interface for the AIT (IPX) or BTM (IGX) ATM trunk cards.

The AIT-T3 backcard provides a T3 interface for the AIT (IPX) or BTM (IGX) ATM

An automatic rerouting of a failed connection by a node to a new route through the network to maintain service.

The line code used for T1 and E1 lines where the "1s" or "marks" on the line alternate between positive polarity and negative polarity.

A BPX administration processor that polls each network port to control the data flow in and out of the crosspoint switch matrix.

An alarm front card for the IPX.

An alarm interface back card for the IPX and IGX.

An alarm front card for the IGX.

An alarm front card and back card set for the BPX.

Data transmission that uses a very flexible method of carrying information, including voice, data, multimedia, and video between devices on a local or wide area network using 53-byte cells on virtual circuits. The 53 byte cell consists of data and a small header. See also cell relay.

A member of the INS product family that uses ATM SVC Server Shelves and software to enhance a StrataCom network with ATM switched virtual circuits.

An adjunct processor used in the INS ATM SVC application to enhance traditional StrataCom networks with ATM switched virtual circuits. The ATM SVC Server Shelf is co-located with and connected to a BPX.

An RS-232 port on the front panel of the SCC card used for connecting a printer or an out-dial modem. This port is a one-way, outgoing port.

B

A protocol for T3 lines that converts a channel word with three consecutive zeros into a code which, at the far end, is converted back to three zeros.

A T1 line protocol that converts a channel word with eight consecutive zeros into a code which, at the far end, is converted back to eight zeros. Allows 64 Kbps clear channel operation while assuring the ones density required on the T1 line.

An IPX software feature that allows circuits to automatically become active (or "upped") at a specified time and date and downed at some later time and date. For circuits that do not need to be available 100% of the time.

In ISDN, a full-duplex, 64-kbps channel used to send user data. Also known as the bearer channel. Compare with D channel.

The control card for the BPX

E1 interface card used on IPX and IGX

E3 interface card used on IPX and IGX

J1 interface card used on IPX and IGX

Subrate interface card used on IPX and IGX

T1 interface card used on IPX and IGX

T3 interface card used on IPX and IGX

Y1 interface card used on IPX and IGX

The address of the slot.port.channel for which the Bframe is destined. This address is part of the Bframe header and is only used across the switch fabric locally in the node.

The BPX frame is the 64-byte format for messages used to encapsulate ATM cells which are sent across the switch fabric.

Presence or absence of extra "1" bits on a T1 transmission facility caused by interference or a failing line repeater. These extra or missing bits interrupts one of the rules for bipolar pairs of a digital transmission line.

ITU-T communication standards designed to handle high-bandwidth applications. Compare with ISDN.

The front card used to network BPXs together and to connect to AXIS shelves, and IPX and IGX nodes configured as shelves. Supports T-3, E-3, and OC3 trunks carrying ATM cells.

A high-speed broadband, high-capacity ATM cell relay network switch from StrataCom for private and public networks.

ISDN interface composed of two B channels and one D channel for circuit-switched communication of voice, video, and data. Compare with PRI.

Frame relay connections grouping a number of ports into one permanent virtual circuit.

The BTM provides an ATM trunk interface for the IGX. The BTM operates in conjunction with a backcard, AIT-T3 or AIT-E3.

A series of BPX cards, BXM-T3/E3, BXM-155, or BXM-622 which can be configured for either trunk or line (service access) modes. These cards support ATM Traffic Management 4.0, including VSVD congestion flow control.

C

A function excercized by switches during connection setup to determine whether or not a connections requested QoS will violate QoS for existing connections.

A signalling mode in E1 transmission where the signalling bits for all 30 E1 channels are carried in timeslot 16. Timeslots 1 to 15 and 17 to 31 carry encoded voice bits only.

ATM Connection type for constant bit rate traffic such as voice or synchronized data requiring a low variation in delay. See also, VBR and ABR

A parameter utilized in defining ATM Constant Bit Rate service. The amount of delay that is acceptable between ATM cells for them to be accepted as compliant (usable).

An International telecommunications advisory committee established under the United Nations to recommend worldwide standards for data and voice communications.

A carrier signalling mode in E1 transmission where signalling bits are not used. CCS typically separates user data from signalling information. A signalling channel is used to provide signalling for all other user data channels in the system.

An IPX dual-purpose front card that can carry voice traffic, a combination of voice and data, or just data. The CVM card is used in conjunction with a BC-T1, BC-E1, or BC-J1 backcard.

Controls time scale over which the PCR is policed.

A unit of data with a fixed number of bytes. For ATM the cell size is 53 bytes.

A form of digital communications using fixed length cells consisting of data and a small header IPX FastPacket was an early implementation of cell relay. The 53 byte ATM cell consists of data and a small header.

CEPT is the European Conference of Posts and Telecommunications Administrations. This association is comprised of European Telecommunications service providers that participate in relevant areas of the work of CEN/CENELEC.

A major alarm condition for a T1 multiplexer or PABX that results in all channels being taken out of service.

The logical end point for a connection.

A T1 or E1 line that connects a user device, such as a PABX or channel bank to the IPX. Carries customer DS0 voice and data circuits. See also line.

When all eight bits of a channel word in the T1 line signal are available for transmitting customer data with no restrictions on content. Also referred to as 64 Kbps clear channel.

A frame relay connection parameter that specifies the number of packets allowed in the initial burst of data after which the data bandwidth is reduced to the connection's minimum specified bandwidth.

Consolidated Link Layer Management. A protocol used to transmit ForeSight messages across the frame relay NNI port.

Cell loss Priority. CLP Hi and CLP Lo thresholds are configurable.

Refers to interworking of a connection with respect to the IPX and IGX nodes. For example, in a Frame Relay to ATM interworking, the Frame Relay data is extracted from FastPackets and transformed to ATM cells with redundant overhead bits discarded.

The sum of the data rates for all circuits transmitting on the same synchronous or frame relay data card.

An RS-232 port on the face plate of a back card for a controller card, (BCC, NPC, NPM) that may used for connecting a control terminal. This port is bi-directional.

The priority assigned each user connection. Defines which circuits get rerouted first during a network failure.

A software feature that is used to conserve network bandwidth by automatically "downing" a voice connection when the signalling status indicates an inactive (on-hook) circuit. The circuit is automatically "upped" when the circuit becomes active.

A method of error checking that detects errors in a block of data. Unlike parity checks, the CRC can detect multiple data errors within the block and thus equipment using a CRC error check can derive a error rate.

A two-dimensional data switch type that is arranged in a matrix of all input connections along one axis and all output connections along the other axis. Each input and output line has a switch point where the two axis intersect that can be enabled (switch closed) or disabled (switch open). The central matrix switch providing the switching matrix for traffic routing by the BPX node.

A network protection unit that terminates any T1 span line connected to the carrier's central office, providing receive direction regeneration and maintenance loopback for the 1.544 Mbps signal.

D

A digital signal format with 24 eight-bit channels plus one synchronizing bit per T1 line. Channels are assigned in a straight, numeric sequence.

Equipment, usually found in the telephone company central office, that is used to groom and retime the 24 channels in a DS1 signal. Individual DS0 channels can be cross-connected from one DS1 source and inserted in another DS1 source either with the same or with a different channel number.

The adjunct processor used in INS Dial-Up Frame Relay applications to provide frame relay dial-up and dial-backup circuits. The DAS Server Shelf is co-located with and connected to an IPX or IGX.

As defined by the RS-232 standard, any device that transmits or receives information. Usually used with data terminal equipment (DTE, like a computer or network node).

A message-oriented ISDN signalling channel, typically carried in DS24 of a PRI on T1 facilities or TS16 of a PRI on E1 facilities. Compare to B channel.

An AT&T dial-up data service offering for 2.4 to 56 Kbps over subscriber loop cable. Requires a Data Service Unit, DSU, at customer premise for interface to the DDS trunk.

The first 8 bits of a FastPacket Address.

An optional feature that saves data channel bandwidth by analyzing data channel content and suppressing repetitive data patterns.

Another name for the INS Dial-Up Frame Relay application.

An INS application that uses a DAS Server Shelf and software to enhance StrataCom networks with frame relay soft permanent virtual circuits (SPVCs) for dial-up dial-backup connections.

A field in a frame relay data packet that identifies the destination for the data.

A grouping of nodes sharing common interests or attributes.

A unique name consisting of the letter "D" immediately followed by a number (1-8) delineated by a "." (period) from the node name (1-8 characters maximum). Example: D1.alpha

A number from 1-8 assigned with the cnfdmn command. The number assigned is part of the domain name.

Digital Private Network Signalling System. A common-channel message-oriented signalling protocol commonly used by private branch exchanges (PBXes). The INS Voice Network Switching application supports DPNSS signalling.

A 64 Kbps channel used to transmit encoded voice and/or data. There are 24 DS0 channels in a circuit T1 (DS1) line. DS0 data is transmitted using one or more DS0 circuits in a T1 or E1 circuit line.

An extension of DS0 that defines the format for assembling various low-speed data circuits (1.2 to 19.6 Kbps) into a single 64 Kbps DS0 channel.

A digital transmission standard that carries 24 individual channels in a bipolar, high-speed line signal at 1.544 Mbps. DS1 signal level is ±3V.

An algorithm that analyzes DS0 voice bits for non-speech codes. Suppresses these bits to conserve packet line bandwidth and inserts a code to indicate to the far end that these bits have been removed. Similar to DFM for data channels. Also, referred to as VAD (Voice Activity Detection(.

As defined by the RS-232 standard, any device that generates or utilizes information. See also, DCE.

E

European transmission service at the rate of 2.048 Mbps

Transmission service at a rate of 34.368 Mbps

A frame relay feature to signal the onset of network congestion to external devices. Sets FECN and BECN bits in frame relay header to indicate forward and backward congestion.

The rate at which as source should initially send after an idle period.

F

Same as interleaved EIA. Seven data circuit control leads in each direction are transmitted in alternating bytes with data. For fast control lead response to data being turned on and off but with a sacrifice in packet line bandwidth.

An AAL5 frame based traffic control that provides the possibility of discarding the whole frame, not just one compliant cell. This avoids wasting bandwidth by continuing to send the cells in a frame once a cell has been found to be non-compliant.)

An enhancement option to GCRA that allows an entire frame to be discarded if any of its cells are non-compliant, rather than transmitting a partial frame over the network.

A non-structured network, a network in which there are no junction nodes or domains.

An adjacent network that is owned and managed by a different party than the one that owns the local network.

A proprietary optional feature that uses feedback techniques to dynamically allocate extra bandwidth to frame relay and ATM connections when the network bandwidth is available and not used by other connections. See also VSVD.

A software feature allowing point-to-point frame relay type connection for various data applications that do not conform to the Frame Relay Interface Specification.

The FPC is used with an FTC (IPX) or FTM (IGX) card. The FPC provides either a T1, E1, V.35, or X.21 interface.

A tag for a frame relay circuit which indicates the class of service to be provided for this connection. Parameters associated with a connection class include minimum information rate guaranteed, peak information rate expected, maximum network delay, etc.

The backcard for an FRP (IPX) or FRM (IGX) card. The FRI provides V.35, X.21, T1, or E1 interfaces.

An IPX frame relay front card that supports 1-4 data ports, and in single-port mode, operates up to 2.048 Mbps. The card is used in conjunction with FRI-V.35, X.21, T1, or E1 backcards.

An IGX frame relay front card that supports 1-4 data ports, and in single-port mode, operates up to 2.048 Mbps. The card is used in conjunction with FRI-V.35, X.21, T1, or E1 backcards.

An IGX frame relay front card that provides an interface to the frame relay Port Concentrator Shelf (PCS). The card is used with the FRI-2-X.21 backcard which connects to the PCS.

An IPX frame relay front card that provides an interface to the frame relay Port Concentrator Shelf (PCS). The card is used with the FRI-2-X.21 backcard which connects to the PCS.

An IPX frame relay front card that provides an interface to the frame relay Port Concentrator Shelf (PCS). The card is used with the FRI-2-X.21 backcard which connects to the PCS.

A packet interface data transmission protocol used for connecting widely-separated LANs. Characterized by long intervals of no data to be sent interspersed with bursts of large volumes of data; sometimes referred to as "bursty data".

A T1 error condition caused by a timing problem between the network and the IPX. When this happens, the IPX inserts a blank DS1 frame or drops an idle DS1 frame so there is no loss of customer data.

The sum of the fixed and propogation delays from the source to a destination and back.

A message sent across the NNI indicating the A-bit status of all connections routed across this NNI frame relay port.

An IPX frame relay front card that provides an interface to a FastPAD. The FTC is used with an FPC backcard. that provides either a T1, E1, V.35, or X.21 interface.

An IPX frame relay front card that provides an interface to a FastPAD.

G

An IPX node that is configured to handle both T1 and E1 packet and circuit lines for direct interface international circuits. (See also Seamless International IPX Network.)

GCRA is a "continuous leaky-bucket" process that monitors the cell depth in the input queue for each PVC to determine whether to admit a new cell to the network without setting the Cell Loss Priority bit.

A frame relay addressing convention that uses the DLCI to identify a specific end device somewhere else in the frame relay network. In a global addressing scheme, the DLCI is a unique number for each port in the network.

Frame relay connections grouping a number of ports onto one permanent virtual circuit. Similar to bundled connections except the grouped connections do not have to be contiguous, nor do they all have to be added simultaneously.

H

A new line interface for E1, similar to B8ZS for T1, which eliminates patterns with eight or more consecutive zeros. Allows for 64 Kbps clear channel operation and still assure the ones density required on the E1 line.

An IGX front card that supports one to four medium speed, synchronous data channels.

I

A multi-service, multi-band ATM cell relay network switch from StrataCom for private and public networks.

INS is the broad name for a range of products that enhance traditional StrataCom networks. These products include Dial-Up Frame Relay, Voice Network Switching, and ATM Switched Virtual Circuits.

Connections within a domain including but not going beyond the junction nodes.

Connections between domains through junction nodes.

Same as "Fast EIA".

A narrowband cell relay network switch from StrataCom for private and public networks.

The customer support group at StrataCom that provides assistance in solving network or equipment problems over the telephone.

A service provided by the telephone company or OCC that supports combined customer voice and data connections over the twisted pair subscriber loop. Requires special equipment at the customer premise and a connecting central office switch that is capable of providing ISDN.

J

A. multiplexed 24-channel circuit line to a PBX conforming to the Japanese TTC-JJ-20 circuit standard. Similar to E1, it operates at 2.048 Mbps.

A node handling inter-networking of domains.

A packet line connecting junction nodes.

L

The logical connection used to represent an individual routing entity.

An IGX data front card that supports up to 8 synchronous or asynchronous data ports. When used with an LDI4/DDS, an LDP can provide 56-Kbps Digital Data Service (DDS) interfaces to the IGX.

An IPX data front card that supports up to 8 synchronous or asynchronous data ports. When used with an LDI4/DDS, an LDP can provide 56-Kbps Digital Data Service (DDS) interfaces to the IPX.

An expansion back card for the IPX32 that connects upper shelf bus to lower shelf bus and the active NPC to standby NPC.

Connects a user device to a service interface, for example, a router to an ASI or AUSM card, a data line to a data card, a frame relay line to an FRP or a port concentrator, or a T1 or E1 line to a CDP card.

The network connection between two nodes.

The protocol and procedures for control of IPX frame relay connections. Used for configuration, flow control, and maintenance of these connections.

A frame relay addressing convention that uses the DLCI to identify the IPX frame relay port at the interface between the user device and the frame relay network. In local addressing, a particular DLCI is used only at the local FR connection. The DLCI may be reused at any other IPX node in the network.

An IPX alarm indicating that the associated T1 line is down due to a local failure of the its receive path.

An IPX utility bus (LB/0 or LB/1), located on the midplane, which provides the electrical connections between various front and back cards. For example, the front and back cards of the Low Speed Data PAD group (LDP and LDI) plug into this utility bus.

A frame relay circuit consisting of either 1, 6, 24 (T1), or 31 (E1) contiguous DSO's on a T1 or E1 physical port.

M

A local or remote failure that is affecting operation of the network.

Maximum number of cells which may burst at the PCR but still be compliant.

The minimum cell rate that is supported by an ATM connection for an ABR connection.

The minimum information rate that is supported by a frame relay connection.

A local or remote failure that is not affecting operation of the network, but nonetheless should be investigated.

A high-speed IPX backplane bus that carries data and timing between card slots for both circuit line and packet line data. Consists of the TDM bus carrying the data and the system clock bus that is used to synchronize all data flowing on and off the TDM bus.

N

A redundancy method in which a group of cards share the same standby redundant card.

The protocol at a frame relay port that serves as a bidirectional interface between a local StrataCom network and a separate and independent "other" network.

An IPX/IGX/BPX serving as a connection point to the network. At a node, connections from service lines are routed to trunks for transmission to other nodes in the network.

Micro-processor based system controller front card that contains the software used to operate the IPX.

Micro-processor based system controller front card that contains the software used to operate the IGX.

Maximum number of cells a source may send for each forward RM cell, i.e., an RM cell must be sent for every Nrm-1 data cells.

IPX front card that coordinates fastpacket trunk traffic to another node via a number of backcards: T1, E1, Y1, and subrate (RS449, X.21, and V.35)

IGX front card that coordinates fastpacket trunk traffic to another node via a number of backcards: T1, E1, Y1, and subrate (RS449, X.21, and V.35)

O

Standard optical transmission facility rate of 155.20 Mbps.

In the United States, reference to all the other telecommunications companies providing various transmission services other than AT&T.

P

Packet line referred to a line used to carry FastPackets between IPX nodes in a network. The term in these documents is replaced by the more general "trunk" which is defined as a physical link from node to node, node to shelf, or node to network. The trunk may be one that supports 24-byte FastPackets (packet trunk), or one that supports 53 byte ATM cells (cell trunk).

A system that breaks data strings into small units (packets), then individually addresses and routes them through the network.

A device that converts a serial data stream into discrete packets in the transmit direction and converts the received packets back into a serial data stream. Adds header information in the transmit packet to allow it to be routed to the proper destination.

One control lead in each direction, generally RTS-CTS, is transmitted in same byte as seven data bits. For fast control lead response to data being turned on and off.

Digital or analog telephone switchboard, classified as customer premise equipment (CPE), used to connect private and public telephone networks

The system for transmitting telephone signals digitally. Voice is sampled 8000 times per second and converted to an 8-bit digital word.

The maximum rate for an ATM connection at which cells are allowed into the network.

The PCS is an external shelf that expands the capacity of the FRP card. The PCS is sued with the FRP-2 (IPX) or FRM-2 (IGX) card to 44 frame relay connections. The PCS connects to the FRI-2.X.21 backcard.

The peak level in bits per second allowed for a frame relay connection.

A protocol defined for use with Switched Megabit Data Service. Used on DS3 ATM trunks in the BPX.

A custom VLSI processor used in the T3 ATM port interface of the BPX BNI card to handle the coding and decoding of the PLCP bit structure. Functions handled by the PLPP include header check sequence generation and checking, DS3 framing, and optional payload scrambling/descrambling.

A network where there is more than one source of network timing. The multiples sources must be operating at the same frequency but are not phase locked (synchronous) with each other.

PNNI consists of two parts:

1. Protocol for distributing topology information between switches and groups of switches.

2. Protocol for signaling process for establishing connections across a network.

Refers to a signal connection on a data back card that interfaces to a customer circuit or data device. The number of ports on a card ranges from 1 to 8 depending on the particular card type.

An ISDN interface to primary rate access. Primary rate access consists of a single D channel for signalling and 23 (T1) or 30 (E1) B (bearer) channels for user data. A PRI is typically carried on T1 or E1 facilities.

A level between 1 and 6 that is assigned to each IPX command. Each operator is assigned a privilege level by the system administrator. The operator may only access and execute commands equal to or lower than his or her own privilege level. Level 1 is the highest and level 6 is the lowest.

Permanent Virtual Connections (circuits). Connections that are assigned but not connected until data is sent, thereby not using bandwidth when idle.

Q

ITU-T specifications for the ISDN use network interface (UNI) data link layer.

A common-channel message-oriented signalling protocol, defined by the European Telecommunications Standard Institute (ETSI), commonly used by private branch exchanges (PBXes). The INS Dynamic Network Switching application supports QSIG signalling to the StrataCom network.

A buffer that is used to temporarily hold data while it waits to be transmitted to the network or to the user.

R

Controls the amount by which the cell transmission rate may increase upon receipt of an RM cell.

Controls the amount by which the cell transmission rate may decrease upon receipt of an RM cell

Another name for local alarm as the local alarm lamp on most digital transmission equipment is red in color.

An IPX alarm indicating that the associated T1 line is down due to a receive line failure on another node. See also yellow alarm.

Also called data frame multiplexing (DFM). An option for data circuits where repeating strings of data are replaced on the packet line by a single occurrence of the data string and a code that indicates to the far end how may repetitions of the string was being transmitted. Used to conserve network bandwidth.

A type of signaling used on T1 lines where the signaling bits for each channel are substituted for the least significant voice bit in each channel word during frames 6 and 12.

A physical and electrical interface standard for a low-speed, unbalanced, serial, data interface adopted by the EIA committee on data communications. Generally used for data circuits operating at data rates below 56 Kbps.

Another EIA standard electrical interface for serial data circuits operating at higher data rates than RS232. RS422 is a balanced interface; RS423 is unbalanced. Uses RS-449 for the physical interface (connector).

The physical interface for the RS422 and R423 electrical interfaces. Contains the Processor Controller Card and the PCC utility bus, and provides system timing and control via the system bus.

S

The process of breaking a dataframe containing data from a number of virtual paths or circuits apart so that the individual paths/circuits can be switched by reassembling the data into a new frame with a different sequence.

An IPX backcard that works in conjunction with the NPC. The SCC provides a centralized clock generation function and provides serial and LAN port interfaces.

An IGX backcard that works in conjunction with the NPM. The SCM provides a centralized clock generation function and provides serial and LAN port interfaces.

Rate above which incoming cells are either tagged or discarded.

An IPX front card that supports one to four medium speed, synchronous data channels.

The back card for the SDP (IPX) or HDM (IGX) cards. The SDI is available with V.24, X.21, and V.35 interfaces.

An IPX network that is configured to carry traffic over international borders (E1-T1 or T1-E1)—see also gateway.

Refers to FastPacket to ATM interworking with respect to the IPX and IGX nodes. In the simple gateway mode, FastPackets are encapsulated in their entirety into cells. See also, complex gateway.

A set of circuits common to all BPX cards used for transmitting and receiving via the crosspoint switch.

A PVC in the INS Dial-Up Frame Relay application that is dormant in the networks database until it is activated by a call into the network by a user.

An IPX network topology in which there is only one path available between any two sources in a frame relay multicast group. Spanning trees are required to prevent frames broadcast from a single source to multiple receptors from circulating endlessly around the network a result of frame relay circuits not having properly closed loops.

Determining the presence or absence of speech for Digital Speech Interpolation. Performed in either the CDP card or VDP card in an IPX node.

A data clocking configuration where the timing for the transmit data is obtained from one source (e.g. user device) and the timing for the receive data is obtained from another source (e.g. IPX).

A message transmitted by a FR NNI port requesting an updated status from the attached foreign network. This message is used as a heartbeat to detect when a port has failed.

On the BPX, contains crosspoint wiring used to carry ATM trunk data between both the network interface and service interface modules and the crosspoint switch as well as providing control, clock, and communications.

A Unix-based workstation and software used as a network management system (NMS) for StrataCom networks. It is part of the StrataSphere group. Provides a graphical user interface for configuration, maintenance, administration of the network. Collects and displays network statistics.

A standards based multi-protocol management architecture that includes StrataView Plus, StrataSpere Connection Manager, StrataSphere BILLder, StrataSphere Modeler, and StrataSphere Optimizer.

Multiple low-speed data circuits carried in a single DS0 timeslot.

Single high-speed data circuit carried in multiple DS0 timeslots.

Long term limit on the rate a connection can sustain.

A virtual circuit that is dynamically established on demand and torn down when transmission is complete. SVS do not need to reserve any network resources when they are not in use. Called a switched virtual connection in ATM terminology. Compare with PVC.

A two-part IPX data bus. One part carries system commands between the PCC all other IPX cards; the other carries time division multiplexed data.

T

The standard US. multiplexed 24-channel voice/data digital span line. Operates at a data rate of 1.544 Mbps.

Transmission service at DS3 rate of 44.736 Mbps

The negotiated number of cells that the network would prefer to limit the source to send during the start-up period.

The process of combining several communication channels by dividing a channel into time increments and assigning each channel to a timeslot.

A field in certain FastPacket formats that indicates the amount of time the packet has spent waiting in queues during the transmission between its source and destination nodes. Used to control the delay experienced by the packet.

An upper bound on the time between RM cells for an active source, i.e., RM cell must be sent at least once every Trm msec.

A physical link between two nodes. The trunk may be one that supports 24-byte FastPackets (packet trunk), or one that supports 53 byte ATM cells (cell trunk)

A set of signalling and information bits that indicate a DS1 line failure.

The buffers in packet line cards (NTC, TXR) where the various FastPackets are queued up for transmission over the packet line(s). The buffers attempt to prioritize each packet so it experiences minimum delay.

U

An analog to digital encoding scheme used to convert voice samples to an 8-bit data word used in D3/D4 T1 multiplex equipment.

Unspecified Bit Rate

The user to network interface, as for ATM connection to CPE. See also NNI.

A general procedure for controlling the rate of user data applied to an ATM network. There are a number of different algorithms for performing UPC. See also GRCA.

A single-chip device used in certain applications that allows microprocessors to communicate with input/output (I/O) devices.

The protocol at a frame relay port that passes information between the network and the user device attached to the port.

V

A CCITT interface standard often used for data transmission over modems.

A data communications interface standard adopted by the CCITT. Often used for data circuits operating at 56 Kbps and above.

Used to statistically compress voice by not sending packets in the absence of speech.

Connection type for variable bit rate traffic such as bursty data. See also, CBR and ABR.

Frame relay buffer allocation parameter that specifies the maximum queue size reserved in the FRP card for the FR connection.

A circuit that acts like it is an individual transmission path but is actually shared with other circuits over a single transmission path. See also PVCs.

The adjunct processor used in the INS Voice Network Switching application. The VNS is co-located with and connected to an IGX or IPX.

An INS application used to provide voice or data switched virtual circuits over a StrataCom network for PBXes using either QSIG or DPNSS signalling.

ATM Forum Traffic Management 4.0 method of providing congestion flow control for ABR connection types. Resource Management (RM) cells are used to convey management information between sources and destinations.

An IPX control terminal that is the active control terminal at one node but is physically attached to another node.

W

A network of transmission circuits generally spanning a large region or territory for transmission of voice and data between widespread end users. An IPX network is an example of a WAN.

X

A CCITT standard for data interfaces transmitting at rates up to approximately 2 Mbps.

A commonly-used standard that defines the protocol for low-speed data packet networks

A simple communications protocol for controlling the flow of data from one device to another. An XON sent from a receiving device indicates it is ready to accept data and the transmitting device may begin to output data. An XOFF from the receiving device indicates that it can no longer store any more data and the transmitting device should temporarily cease transmitting.

Y

A short adapter cable forming an electrical branch (thus the term Y) for connecting a single customer data or trunk connection to two identical back cards to provide hardware redundancy on the IPX.

A redundancy type used in the IPX when a 1:1 card redundancy is implemented using a split or Y-cable for the data connection between the user device and the primary and standby IPX interface card.

A digital trunk conforming to the Japanese "Y" circuit standard, for use as a packet line. Similar to T1, it operates at 1.544 Mbps.

Another name for remote alarm as the remote alarm lamp on digital transmission equipment is always yellow in color.

Posted: Thu Jan 18 12:57:38 PST 2001
All contents are Copyright © 1992--2001 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.