cc/td/doc/product/wanbu/access/aprod
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Specifications

Specifications

Environmental Specifications

The FastPAD environmental specifications are listed in Table A-1.


Table A-1: Environmental Specifications
Specification Range

Temperature

0° C < T < 45° C

Relative Humidity

5- 80% for 0° C < T < 30° C

Absolute Humidity

< 24 g/m

Atmospheric Pressure

70-106 kPa

Operating Altitude

Lower than 2,500 meters

Power Specifications

Color Code

The colors of wires within the power supply cable are listed in Table A-2.


Table A-2: Wire Colors within the Power Supply Cable
120 VAC 220/240 VDC 48 VDC

Phase

Black

Brown

-

Neutral

White

Blue

-

Ground

Green/green/yellow

Green/yellow

Green/yellow

+48

-

-

Brown

-48

-

-

Blue

Stand-Alone Models

mp, mp12

Power specifications for the mp and mp12 are listed in Table A-3.


Table A-3: Power Specifications for the mp and mp12
220 VAC Version 120 VAC Version 48 VDC Version

Nominal voltage

Single phase with Ground 220V/240V

120V

48 VDC

Tolerance

187 - 255 V

104-127 V

40-57 V

Frequency

50 - 60 Hz

50 - 60 Hz

Maximum current

350 mA

600 mA

1A

Power
consumption

40W

40W

40W

Power Specifications for the mp6

Power specifications for the mp6 are listed in Table A-4.


Table A-4: Power Specifications for the mp6
A4 AC/AC Adaptor DC Source

Input

Nominal voltage (V)

230 +/- 10%

240 +/- 10%

115 +/- 10%

48 (40-57)

Frequency (Hz)

50-60

50

60

-

Current (MA)

102

102

200

400

Output

Voltage (V)

2 x 13

2 x 13

2 x 13

-

Current (MA)

690

690

650

-

Power Specifications for the Universal Shelf

Power specifications for the universal shelf are listed in Table A-5.


Table A-5: Power Specifications for the Universal Shelf
220 V Version 120 V Version 48 V Version

Nominal voltage

Single phase with Ground 220V/240V

120V

48 VDC

Tolerance

187- 255 V

104-127 V

40-57 V

Frequency

50-60 Hz

50-60 Hz

Maximum current

1.6 A

3.1 A

6 A

Electromagnetic Compatibility

This equipment is in accordance with the EN55022, assuming that all interface cables used are from the same manufacturer.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct at their own expense.

General Specifications

Access Rate

The access rates are listed in Table A-6.


Table A-6: Access Rates

BOP (kbps)

0.6, 1.2, 2.4, 4.8, 14.4, 19.2, 38.4, 48, 56, 64, 72, 128, 144, 256, 512, 1.024 Mbps (DCE), 1.544 Mbps (DTE), 2.048 Mbps (mp12 of mprxx only).

COP (kbps)

0.6, 1.2, 2.4, 4.8, 14.4, 19.2, 38.4, 48, 56, 64

Asynch (bps)

75, 110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400.

Interfaces

V24/V28, X.21/V.10, V.11; X.21bis/V.10, V.11; V.35, ISDN, G.703 non-channelized.

mp6 interfaces

3 each fixed V24/v28 DCE interfaces, speeds below 19.2 guaranteed 2 each variable V.11 or V24/V28 DCE interfaces, up to 1.75 Mbps, 1 each variable V11/v24/v28/v35/ISDN DTE/DCE interface, line speeds up to 1.75 Mbps.

mp interfaces

12 ea. variable V11/V24/V28/V35 ISDN DTE/DCE interface, line speeds up to 1.75 Mbps.

mp12 interfaces

12 ea. variable V11/V24/V28/V35/ G.703/ ISDN DTE/DCE interface, line speeds up to 2.3 Mbps.

mpr interfaces

12 ea. variable V11/V24/V28/V35/ G.703/ DTE/DCE interface, line speeds up to 2.3 Mbps.

Loading

On mp12-based modules and the mprxx, aggregate line speed on any three consecutive ports (0-1-2, 3-4-5, 6-7-8, 9-10-11) may not exceed the maximum line speed of 2.3 Mbps. This is due to the architecture of the internal MC68302 microprocessor.

Dimensions

FastPAD

Dimensions are listed in Table A-7.


Table A-7: Dimensions

mp6 case

mp6 card

mp, mp12, mprxx stand-alone

mp, mp12, mprxx card

Width

218 mm

66 mm

218 mm

233 mm

Height

71 mm

1.6 U

218 mm

133 mm

3 U

218 mm

Depth

370 mm

370 mm

455 mm

355 mm

Shelf space used

-

6 slots

-

12 slots

Maximum per shelf

-

6

-

3

Shelf

Shelf dimensions are listed in Table A-8.


Table A-8: Shelf Dimensions

Width

19 inches

Height

5 U

Depth

370 mm

MTBF

Mean time between failure rates are listed in Table A-9.


Table A-9: Mean Time Between Failure Rates at 20°C

mp6

105,000 hours

mp

65,000 hours

mp12

50,000 hours

mpr



60,000 hours

ICard

1.5 million hours

MTTR

Mean time to repair rates are as follows:

Microprocessor Connectivity

When high-speed lines are used, the lines have to be chosen according to the connectivity of the microprocessor and the line that it manages.

Figure A-1 illustrates the line separation according to the MP.


Figure A-1: Line Separation According to the mp


Table A-10 lists the microprocessor connectivity according to the equipment.


Table A-10: Microprocessor Connectivity
FastPAD Mb/s/module

mp6

1. 75

mp

1. 75

mp12

2. 3

mprxx

2. 3

Example:

For the mp6, the main connectivity is 1.75 Mb/s. If 2 T1 lines need to be used, it will be on two different processors (for example, line 0 on Ma and L3 on Mb).

For the mp12, the connectivity is 2.3 Mb/s. If a V.11 interface is used on L0 to provide T1 access, line L1, L2 can share 256 kb/s. If a G.703 interface is used, L2 can be used up to 256 kb/s, since L1 is not accessible. (refer to G.703).


hometocprevnextglossaryfeedbacksearchhelp
Posted: Thu Jan 25 13:32:44 PST 2001
All contents are Copyright © 1992--2001 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.