Table Of Contents
Voice Menu Codes
Voice Menu Codes
This section contains a quick-reference list of the voice configuration menu options for the Cisco ATA. For information on the use of the voice menu, see " Chapter 3, "Configuring the Cisco ATA for SCCP."
This tables in this section contain the following information:
•
Cisco ATA voice menu information options— Table B-1
•Cisco ATA voice menu configuration parameters— Table B-2
•Cisco ATA voice menu software-upgrade options— Table B-3
Note Follow each voice menu code with #.
Note The term Cisco ATA is used throughout this manual to refer to both the Cisco ATA 186 and the Cisco ATA 188, unless differences between the Cisco ATA 186 and Cisco ATA 188 are explicitly stated.
Table B-1 lists codes to return basic Cisco ATA information.
Table B-1 Cisco ATA Voice Menu Codes—Information Options
Option
|
Voice Menu Code
|
Description
|
Build information
|
123123
|
Build date of the Cisco ATA software
|
Obtain basic network status
|
3123
|
For complete information of the status this code provides, see the "Obtaining Network Status Prior to Getting IP Connectivity" section on page 8-11.
|
Review IP address
|
21
|
Returns IP address of the Cisco ATA
|
Review MAC address
|
24
|
Returns media access control (MAC) address of the Cisco ATA
|
Review network route IP address
|
22
|
Returns IP address of the network route
|
Review subnet mask
|
23
|
Returns subnet mask of the network route
|
Version number
|
123
|
Returns version number of the Cisco ATA software
|
Table B-2 lists configuration codes. For additional information about these parameters, see " Chapter 5, "Parameters and Defaults."
Table B-2 Cisco ATA Voice Menu Codes—Configuration Parameters
Option
|
Voice Menu Code
|
Description
|
Audio mode
|
312
|
Allows finer control of the audio component to suit certain user applications
|
Caller ID method
|
316
|
Specifies the signal format when generating the Caller ID format to use
|
Connection mode
|
311
|
Controls the connection mode of the call signaling protocol
|
Dynamic Host Configuration Protocol (DHCP)
|
20
|
Controls whether the Cisco ATA can automatically obtain configuration parameters from a server over the network
|
DNS 1 IP
|
916
|
IP address of the primary DNS server
|
DNS 2 IP
|
917
|
IP address of the secondary DNS server
|
Encrypt key
|
320
|
Encrypts the configuration file on the TFTP server
|
Num Tx frames
|
35
|
Number of frames transmitted per packet
|
Static IP address
|
1
|
IP address of the Cisco ATA
|
LBR codec
|
300
|
Low-bit-rate codec selection
|
Media port
|
202
|
Specifies which base port the Cisco ATA uses to receive RTP media streams
|
Static network route address
|
2
|
Network router address
|
NPrintf address
|
81
|
IP address of a host to which all Cisco ATA debug messages are sent
|
Set password
|
7387277
|
Configuration interface password
|
Signal timers
|
318
|
Timeout values controlling the starting or stopping of a signaling event
|
MGCP protocol
|
38
|
Selects the signaling protocol
|
Static subnet mask
|
10
|
Specifies the subnet mask for the Cisco ATA
|
TFTP URL
|
905
|
When TFTP configuration is used, IP address of the TFTP server
|
UDP TOS bits
|
255
|
Determines the precedence and delay of UDP IP packets
|
Use TFTP
|
305
|
Enables TFTP as configuration method
|
Table B-3 lists codes used in the software upgrade process. For information about these codes, see " Chapter 7, "Upgrading the Cisco ATA Signaling Image."
Table B-3 Cisco ATA Voice Menu Codes—Software Upgrade
Option
|
Voice Menu Code
|
Description
|
Upgrade software
|
100
|
Used in the software process to enter the IP address of the PC
|
Upgrade language to English
|
101
|
When upgrading software, changes or upgrades the voice prompt language to English
|
