|
|
The Interface Controller Card (ICC) is a high-capacity network interface engine. The ICC card uses the VCO/4K mid-plane architecture which enables the card to connect with a series of I/O modules specific to different network interface requirements. The mid-plane isolates the unique physical characteristics of each type of connection leaving the ICC to perform all of the signaling and protocol processing independently. There are six I/O modules supporting 4, 8, or 16 network spans.
For information on the ICC or ICC I/O Modules, refer to the Cisco VCO/4K Card Technical Descriptions.
The following objects are included in the ICC Card group.
{icc 1}
Description
A list of ICC cards.
Object Identifier
1.3.6.1.4.1.886.1.12.1
Data Type
Sequence of iccEntry
Access Policy
Not accessible
Status
Mandatory
{iccTable 1}
Description
An entry in the iccTable.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1
Data Type
IccEntry
Access Policy
Not accessible
Status
Mandatory
Sequence
iccIndex | CardIndex |
iccType | Integer |
iccRack | Integer |
iccLevel | Integer |
iccSlot | Integer |
iccGroupNum | Integer |
iccIntfNum | Integer |
iccTxGain | Integer |
iccRxGain | Integer |
iccTxClck | Integer |
iccRfClck | Integer |
iccSpanType | Integer |
iccSlip | Integer |
iccOutOfFrame | Integer |
iccCode | Integer |
iccLeng | Integer |
iccCrc | Integer |
iccTs0 | Integer |
iccTs16 | Integer |
iccStatus | Integer |
iccUnusedPorts | Integer |
iccRevVer | DisplayString |
iccPhyAdd | Integer |
iccNfasGrpIndex | Integer |
iccNfasGrpPosition | Integer |
iccAlarm | Integer |
iccErrorStatus | Integer |
iccOwnerString | OwnerString |
iccEntryStatus | EntryStatus |
iccDwnldVersion | DisplayString |
iccUpgradeState | UpgradeState |
iccIsdnAccessType | PriAccessMode |
iccIsdnCaInpulseRuleIndex | InpulseRuleIndex |
iccIsdnNcaInpulseRuleIndex | InpulseRuleIndex |
iccIsdnSwitchType | PriSwitchType |
iccIsdnLaw | LawType |
iccIsdnProtocolT200 | Integer |
iccIsdnProtocolT201 | Integer |
iccIsdnProtocolT203 | Integer |
iccIsdnProtocolN200 | Integer |
iccIsdnProtocolN201 | Integer |
iccIsdnProtocolWindowSize | Integer |
iccIsdnProtocolT303 | Integer |
iccIsdnProtocolT305 | Integer |
iccIsdnProtocolT308 | Integer |
iccIsdnProtocolT309 | Integer |
iccIsdnProtocolT310 | Integer |
iccIsdnProtocolT313 | Integer |
iccIsdnProtocolT315 | Integer |
iccIsdnProtocolT316 | Integer |
iccIsdnProtocolT321 | Integer |
iccIsdnProtocolT3M1 | Integer |
iccIsdnProtocolTM01 | Integer |
iccIsdnProtocolNM01 | Integer |
{iccEntry 1}
Description
The value of this object uniquely identifies an entry in the icc table. It corresponds to the physical location of the card and is a function of the rack (R), level (L), and the slot (S) that the card occupies.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.1
Data Type
CardIndex
Access Policy
Read only
Status
Mandatory
{iccEntry 2}
Description
Specifies the type of icc card. nxT1 and nxE1 indicate non-ISDN types.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.2
Data Type
Integer. Possible values are as follows:
| Value | Card Type |
|---|---|
1 | nxT1 |
2 | nxE1 |
3 | t1IsdnPriNi2 |
4 | t1IsdnPri5Ess |
5 | t1IsdnPri4ess |
6 | t1IsdnPriNti |
7 | t1IsdnPriNtt |
8 | e1IsdnPriNet5 |
9 | e1IsdnPriQsig |
10 | e1IsdnPriTs014 |
Access Policy
Read only
Status
Mandatory
{iccEntry 3}
Description
The rack (R) that the card occupies.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.3
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 4}
Description
The level (L) that the card occupies.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.4
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 5}
Description
The slot (S) that the card occupies
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.5
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 6}
Description
Specifies the group number of an interface.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.6
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 7}
Description
Specifies the interface number of an interface.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.7
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 8}
Description
Only valid when iccType is one of the non-ISDN types, i.e., nxT1 or nxE1. When iccType is one of the ISDN flavors, a get on this object will return unknownOrNa and a set on this object will result in an error.
Indicates the transmit gain control. Possible values include -6 dB, -3 dB, 0 dB, +3 dB, +6 dB. The default value is 0 dB.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.8
Data Type
Integer. Possible values are as follows:
| Value | Transmit Gain Control |
|---|---|
1 | minus6db |
2 | minus3db |
3 | zerodb |
4 | plus3db |
5 | plus6db |
255 | unknownOrNa |
Access Policy
Read-write
Status
Mandatory
{iccEntry 9}
Description
Only valid when iccType is one of the non-ISDN types, i.e., nxT1 or nxE1. When iccType is one of the ISDN flavors, a get on this object will return unknownOrNa and a set on this object will result in an error.
Indicates the reference gain control. Possible values include -6 dB, -3 dB, 0 dB, +3 dB, +6 dB. The default value is 0 dB.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.9
Data Type
Integer. Possible values are as follows:
| Value | Reference Gain Control |
|---|---|
1 | minus6db |
2 | minus3db |
3 | zerodb |
4 | plus3db |
5 | plus6db |
255 | unknownOrNa |
Access Policy
Read-write
Status
Mandatory
{iccEntry 10}
Description
T1: Indicates the transmit clock (timing source) for this span. Possible values include SCLK, LOOP, and 1544.
SCLK = VCO system clock
LOOP = incoming line
1544 = board crystal
E1: Indicates the transmit clock (timing source) for this span. Possible values include SCLK, LOOP, and 2048.
SCLK = VCO system clock
LOOP = incoming line
2048 = board crystal
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.10
Data Type
Integer. Possible values are as follows:
| Value | Transmit Clock (timing source) |
|---|---|
1 | sclk |
2 | loop |
3 | tx-1544 |
4 | tx-2048 |
255 | unknown |
Access Policy
Read-write
Status
Mandatory
{iccEntry 11}
Description
T1/MVDCT1: Indicates the reference clock (timing source) for this span. Applies only if this span is specified as the current timing source using either the Master Timing Link Selection menu on the console, the T1 Synchronization Control ($C0 02) host command, or the masTimingSource MIB object. Possible values include LOOP or 1544.
LOOP = incoming line
1544 = board crystal
When you choose a span as the master timing source, the reference clock for the span creates the VCO system clock.
E1: Indicates the reference clock (timing source) for this span. Applies only if this span is specified as the current timing source using either the Master Timing Link Selection menu on the console, the T1 Synchronization Control ($C0 02) host command, or the masTimingSource MIB object. Possible values include LOOP or 2048.
LOOP = incoming line
2048 = board crystal
When you choose a span as the master timing source, the reference clock for the span creates the VCO system clock.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.11
Data Type
Integer. Possible values are as follows:
| Value | Reference Clock (timing source) |
|---|---|
1 | loop |
2 | rf-1544 |
3 | rf-2048 |
255 | unknown |
Access Policy
Read-write
Status
Mandatory
{iccEntry 12}
Description
T1: Indicates the format of the T1 stream. You can only change this value when the span status is Out of Service (OOS). Possible values include SF, ESF, SF_NR, and ESF_NR.
SF = Superframe
ESF = Extended superframe
SF_NR = Superframe without robbed bit signaling
ESF_NR = Extended superframe without robbed bit signaling.
If you select an SF_NR or ESF_NR span type, the per port SIG TYPE object (iccPortSigType) is ignored.
E1: Indicates the format of the E1 stream. You can only change this value when the span status is OOS. Possible values include CAS/R2, CAS/MC, and CCS/31B.
CAS/R2 = Channel Associated signaling/R2 mode
CAS/MC = Channel Associated signaling/Mercury Mode
CCS/31B = Common Channel signaling/31 Bearer channels.
userDefX = user defined
If you specify the CCS/31 format, the TS16 object (iccTs16) is not meaningful.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.12
Data Type
Integer. Possible values are as follows:
| Value | T1/E1 stream format |
|---|---|
1 | sf |
2 | esf |
3 | sf-nr |
4 | esf-nr |
5 | cas-r2 |
6 | cas-mc |
7 | ccs-31b |
8 | userDef1 |
9 | userDef2 |
10 | userDef3 |
11 | userDef4 |
12 | userDef5 |
13 | userDef6 |
255 | unknown |
Access Policy
Read-write
Status
Mandatory
{iccEntry 13}
Description
Determines the number of transmit or receive Slips that can be detected for this span, in a 24-hour period, before threshold processing occurs. Control this processing with the SLIP/OOF feature flag. Separate Slip maintenance counts are maintained for receive and transmit Slips. When either of these counters reaches the limit, threshold processing occurs. The current Slip count appears on the Diagnostics Card Display screen. Slip counters are reset at midnight and when this object is changed.
Possible values are between 0 (Slip maintenance processing is inhibited—recommended when TRX Clock = LOOP) and 255. The default value is 255.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.13
Data Type
Integer (0...255). Default value is 255.
Access Policy
Read-write
Status
Mandatory
{iccEntry 14}
Description
Determines the number of Out of Frames (OOFs) detected for this span, in a 24-hour period, before threshold processing occurs. Control this processing with the SLIP/OOF feature flag. The OOF counter is reset at midnight and when this object is changed.
Possible values are between 0 (OOF maintenance processing inhibited—not recommended) and 255. The default value is 17.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.14
Data Type
Integer (0...255). Default value is 17.
Access Policy
Read-write
Status
Mandatory
{iccEntry 16}
Description
Only valid when iccType is one of the non-ISDN types, i.e., nxT1 or nxE1. When iccType is one of the ISDN flavors, a get on this object will return unknownOrNa and a set on this object will result in an error.
T1/MVDCT1: Indicates the code on the T1 span.
Possible values include AMI, B7ZS, and B8ZS.
E1: Indicates the code on the span. Possible values include AMI and HDB3. The return value (2) should be interpreted depending on the card type.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.16
Data Type
Integer. Possible values are as follows:
| Value | T1 span code |
|---|---|
1 | ami |
2 | b8zs |
3 | b7zs |
4 | hdb3 |
255 | unknownOrNa |
Access Policy
Read-write
Status
Mandatory
{iccEntry 17}
Description
Only valid when iccType is not nxE1. When iccType is nxE1, a get on this object will return 0; a set on this object will result in an error.
Indicates the line equalization used for the T1/MVDCT1 stream. Possible values include the line length between 0 to 133 feet, 133 to 266 feet, 266 to 399 feet, 399 to 533 feet, and 533 to 655 feet, FCC Part 68 Option A, ITU-T F.703.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.17
Data Type
Integer. Possible values are as follows:
| Value | Line equalization |
|---|---|
0 | none |
1 | leng0-133 |
2 | leng133-266 |
3 | leng266-399 |
4 | leng399-533 |
5 | leng533-655 |
6 | lengPT-68-A |
7 | lengG-703 |
Access Policy
Read-write
Status
Mandatory
{iccEntry 18}
Description
Only meaningful when iccType is any of the E1 types, i.e., nxE1, e1IsdnPriNet5, e1IsdnPriQsig, or e1IsdnPriTs014. When iccType is not of type E1, a get on this object will return 0; a set on this object will result in an error. Indicates if CRC checking is enabled. Possible values include ON or OFF.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.18
Data Type
Integer. Possible values are as follows:
| Value | CRC checking status |
|---|---|
0 | none |
1 | crc-on |
2 | crc-off |
Access Policy
Read-write
Status
Mandatory
{iccEntry 19}
Description
Only meaningful when iccType is of type nxE1. When iccType is not of type nxE1, a get on this object will return 0; a set on this object will result in an error.
Specifies international or national bits of Time Slot 0 as an 8-bit value with the format 'i1Annnnn' where
i = International bits
n = National bits
A = a remote alarm indicator (ITU-T default)
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.19
Data Type
Integer (0..'ff'h)
Access Policy
Read-write
Status
Mandatory
{iccEntry 20}
Description
Only meaningful when iccType is of type nxE1.
When iccType is not of type nxE1, a get on this object will return 0; a set on this object will result in an error.
Specifies extra bits and the C and D bits of Time Slot 16 as an 8-bit value with the format '0000xyxx' where
x = extra bits
y = a remote alarm indicator (ITU-T default). Use bits 3 and 4 (where bit 1 = leftmost bit) to specify the C and D bits.
For systems in China, the C and D bits must be set to 1.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.20
Data Type
Integer (0..'ff'h)
Access Policy
Read-write
Status
Mandatory
{iccEntry 21}
Description
Indicates the current status of the span.
Possible values and their meanings are listed in the following table:
| Value | Meaning |
|---|---|
active | Active (ports on this card can be involved in active calls and can be allocated to new calls) the agent may take up to 10 seconds to set a card to active. |
maintenance | Maintenance (one or more ports on this card may be involved in active calls; no ports are allocated to new calls). the agent may take up to 10 seconds to set a card into maintenance. |
diagnostics | Diagnostics (no ports on this card are involved in calls or allocated to new calls) |
outOfService | Out of Service (no ports on this card can be involved in active calls; no ports are allocated to new calls) |
payloadLoopback | Payload Loopback (diagnostic state) |
remoteLoopback | Remote Loopback (diagnostic state) |
gracefulIdle | Graceful Idle (no ports on this card are allocated to new calls) |
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.18
Data Type
Integer. Possible values are as follows:
| Value | Status |
|---|---|
1 | active |
2 | maintenance |
3 | diagnostics |
4 | outOfService |
7 | payloadLoopback |
8 | remoteLoopback |
9 | gracefullIdle |
Access Policy
Read-write
Status
Mandatory
{iccEntry 22}
Description
Indicates the number of ports not currently active on this card; for multispan cards, indicates the number of ports not currently active on individual spans.
Valid only for network interface and internal service circuit ports.
For systems in China, the C and D bits must be set to 1.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.22
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 23}
Description
Indicates the version and the revision level of the firmware installed on the card. Object can be used to verify that firmware revisions for all network interface and service circuit cards are at the current level.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.23
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 24}
Description
The physical address of this span.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.24
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 25}
Description
Only meaningful when iccType is any of the T1 types, i.e., nxT1, t1IsdnPriNi2, t1IsdnPri5Ess, t1IsdnPri4Ess, t1IsdnPriNti, or t1IsdnPriNtt. When iccType is not of type T1, a get on this object will return 0; a set on this object will result in an error.
A foreign key in the NFAS group table, indicates which NFAS group this span belongs to. In order to change this attribute, you need to set this EntryStatus and the one in the nfasGroupTable to underModification.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.25
Data Type
Integer
Access Policy
Read-write
Status
Mandatory
{iccEntry 26}
Description
Only meaningful when iccType is any of the T1 types, i.e., nxT1, t1IsdnPriNi2, t1IsdnPri5Ess, t1IsdnPri4Ess, t1IsdnPriNti, or t1IsdnPriNtt. When iccType is not of type T1, a get on this object will return 0; a set on this object will result in an error.
Specifies the position of the span in the assigned nfas group.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.26
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 27}
Description
The value tracks which alarms are active on this span. Card alarms are internally represented as a bit map. There are 32 bits in all, a bit is set to 1 for each active alarm. The following is the representation:
| Bit | Alarm Description |
|---|---|
0 | Card failure—minor |
1 | Port failure—minor |
2 | T1/E1/PRI carrier failure—major |
3 | T1/E1/PRI remote carrier failure—major |
4 | T1/E1/PRI card failure—major |
5 | T1/E1 Signaling Bit—minor |
6 | PRI Bipolar Violations MLimit reached |
7 | T1/E1/PRI Out of Frame MLimit reached—minor |
8 | T1/E1 Slip Maint Limit reached—minor |
9 | T1/E1/PRI OOF condition—minor |
10 | PRI D-channel failure—major |
11-32 | Unsigned filler (set to zero) |
The NMS application needs to interpret the alarm status from the integer value returned by this object.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.27
Data Type
Integer (0..'7ff'h)
Access Policy
Read only
Status
Mandatory
{iccEntry 28}
Description
Registers the last error that occurred on this span entry. For a complete list of errors, refer to the "Card Error Messages" section.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.28
Data Type
Integer. Possible values are as follows:
| Value | Error |
|---|---|
4352 | frameTypeInvalid |
4353 | codeInvalid |
4354 | txInvalid |
4355 | rxInvalid |
4356 | txClockInvalid |
4357 | refClockInvalid |
4358 | oofSlipInvalid |
4359 | lawInvalid |
4360 | spanLengthInvalid |
4361 | crcInvalid |
4362 | ts0Invalid |
4363 | ts16Invalid |
4364 | mustBeOos |
4365 | ni2NotInstalled |
4366 | priOnlyNotInstalled |
4367 | valueInvalid |
4368 | spanNotIsdnType |
4369 | spanNotIsdnT1Type |
4370 | spanNotIsdnE1Type |
4371 | spanNotIsdnOrT1Type |
4372 | spanNotT1Type |
4373 | spanNotE1Type |
4374 | spanNotNonIsdnType |
4375 | spanNotNonIsdnE1Type |
4376 | spanNotCompatibleIsdnType |
Access Policy
Read only
Status
Mandatory
{iccEntry 29}
Description
The entity that configured this span entry and is therefore using the resources assigned to it.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.29
Data Type
OwnerString
Access Policy
Read-write
Status
Mandatory
{iccEntry 30}
Description
The status of this icc card entry. This object is used to add/delete an icc card span and to modify span attributes. The span needs to be set to valid once modifications are done.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.30
Data Type
EntryStatus
Access Policy
Read-write
Status
Mandatory
{iccEntry 31}
Description
Version/revision of the card download file.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.31
Data Type
DisplayString (size 1..4)
Access Policy
Read only
Status
Mandatory
{iccEntry 32}
Description
The upgrade state of this trunk card entry.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.32
Data Type
UpgradeState
Access Policy
Read only
Status
Mandatory
{iccEntry 33}
Description
Only applicable when iccType is one of the ISDN span types. A get on this object for a non-ISDN span type will return 0. A set on this object for a non-ISDN span type will result in an error.
Determines the type of access connection used for this span. This object can only be changed when the span status is Out-of-Service. Possible values for this object and their meanings are listed below:
| Value | Meaning |
|---|---|
usrmd | User side implementation for the connection; valid for both T1 and E1 ISDN icc types (except e1IsdnPriQsig). |
netmd | Network side implementation for the connection; valid only for t1IsdnPriNtt, e1IsdnPriNet5, and e1IsdnPriTs014 ISDN icc types. |
symmd | User side symmetrical implementation for the connection (loop-back only); only valid for T1 ISDN icc types: t1IsdnPriNi2, t1IsdnPri5Ess, t1IsdnPri4Ess, and t1IsdnPriNti. |
userA | One side of symmetrical inter-PINX link for the connection; only valid for E1 ISDN icc type: e1IsdnPriTs014. |
userB | One side of symmetrical inter-PINX link for the connection; only valid for E1 ISDN icc type: e1IsdnPriTs014. |
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.33
Data Type
PriAccessMode
Access Policy
Read-write
Status
Mandatory
{iccEntry 34}
Description
Only applicable for ISDN span types. A get on this object for a non-ISDN span type will return 0. A set on this object for a non-ISDN span type will result in an error.
This is a foreign key corresponding to the inpulseRuleIndex in the inpulseTable. It is accessed while assigning a particular inpulse rule to the span. Determines the inpulse rule processed when a SETUP message is received over this span's controlling D-channel. This rule applies when the Channel ID within the SETUP message specifies a B-channel as the bearer channel (call associated connections). If NFAS is being used, an inpulse rule is assigned only to the spans containing the primary and backup D-channels. The inpulse rule chosen must have already been defined using either the Inpulse Rule Table screens on the console, or by an entry in the inpulseRuleTable.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.34
Data Type
InpulseRuleIndex
Access Policy
Read-write
Status
Mandatory
{iccEntry 35}
Description
Only applicable for ISDN span types. A get on this object for a non-ISDN span type will return 0. A set on this object for a non-ISDN span type will result in an error.
This is a foreign key corresponding to the inpulseRuleIndex in the inpulseTable. It is accessed while assigning a particular inpulse rule to the span.
Determines the inpulse rule processed when a SETUP message is received over this span's controlling D-channel. This rule applies when the Channel ID within the SETUP message specifies the D-channel as the bearer channel (non-call associated signaling). If NFAS is being used, an inpulse rule is assigned only to the spans containing the Primary and Backup D-channels. The inpulse rule chosen must have already been defined using either the Inpulse Rule Table screens on the console, or by an entry in the inpulseRuleTable.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.35
Data Type
InpulseRuleIndex
Access Policy
Read-write
Status
Mandatory
{iccEntry 36}
Description
Only applicable for ISDN span types. A get on this object for a non-ISDN span type will return 0. A set on this object for a non-ISDN span type will result in an error.
This is a foreign key corresponding to the inpulseRuleIndex in the inpulseTable. It is accessed while assigning a particular inpulse rule to the span.
Determines the inpulse rule processed when a SETUP message is received over this span's controlling D-channel. This rule applies when the Channel ID within the SETUP message specifies a B-channel as the bearer channel (call associated connections). If NFAS is being used, an inpulse rule is assigned only to the spans containing the Primary and Backup D-channels. The inpulse rule chosen must have already been defined using either the Inpulse Rule Table screens on the console, or by an entry in the inpulseRuleTable.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.36
Data Type
PriSwitchType
Access Policy
Read-write
Status
Mandatory
{iccEntry 37}
Description
Only applicable for ISDN span types. A get on this object for a non-ISDN span type will return 0. A set on this object for a non-ISDN span type will result in an error.
Specifies voice coding on the PRI stream. The system automatically turns off translation for calls which specify unrestricted digital information bearer capability.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.37
Data Type
LawType
Access Policy
Read-write
Status
Mandatory
{iccEntry 38}
Description
Acknowledgement Timer in seconds.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.38
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 39}
Description
Minimum time between retransmission of the TEI Identity check messages in seconds.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.39
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 40}
Description
Maximum time allowed without frames being exchanged in seconds.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.40
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 41}
Description
Maximum number of retransmissions.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.41
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 42}
Description
Maximum number of octets in an information field.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.42
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 43}
Description
Window size.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.43
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 44}
Description
Timer started on SETUP sent.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.44
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 45}
Description
Timer started on DISC.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.45
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 46}
Description
Timer started on REL sent.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.46
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 47}
Description
Timer started on data link disconnection.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.47
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 48}
Description
Timer started on CALL PROC received.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.48
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 49}
Description
Timer started on CONN sent.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.49
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 50}
Description
ISDN PRI layer 3 timer value.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.50
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 51}
Description
Timer started on REST sent.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.51
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 52}
Description
Timer started on D-channel failure.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.52
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 53}
Description
Timer started on SERV sent.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.53
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 54}
Description
Isdn PRI layer 3 timer value.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.54
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 55}
Description
Isdn PRI layer 3 timer value.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.55
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccEntry 56}
Description
The time (in hundredths of a second) since the epoch that the iccTable was last modified.
Object Identifier
1.3.6.1.4.1.886.1.12.1.1.56
Data Type
Integer
Access Policy
Read only
Status
Mandatory
Use the ICC port table section to assign a name, a hardware type, a default inpulse rule, and a class of service (COS) to individual ports on an ICC card.
{icc 4}
Description
A list of port entries on each icc card.
Object Identifier
1.3.6.1.4.1.886.1.12.4
Data Type
Sequence of IccPortEntry
Access Policy
Not accessible
Status
Mandatory
{iccPortTable 1}
Description
An table entry containing objects belonging to a particular port.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1
Data Type
IccPortEntry
Access Policy
Not accessible
Status
Mandatory
{iccPortEntry 1}
Description
Indicates the port number on the span.
For all the T1 Pri span types, port 24 is reserved for the D-channel. For the E1 span types, ports 1 and 17 are reserved.
Maximum number of ports and inaccessible ports for the various types of icc card span are shown below:
| Card Span Type | Max # of Ports | Inaccessible Ports |
|---|---|---|
nxT1 | 24 | None |
nxE1 | 32 | 1 & 17 |
t1IsdnPriNi2 | 24 | 24 |
t1IsdnPri5Ess | 24 | 24 |
t1IsdnPri4Ess | 24 | 24 |
t1IsdnPriNti | 24 | 24 |
t1IsdnPriNtt | 24 | 24 |
e1IsdnPriNet5 | 32 | 1 & 17 |
e1IsdnPriQsig | 32 | 1 & 17 |
e1IsdnPriTs014 | 32 | 1 & 17 |
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.1
Data Type
Integer (1...32)
Access Policy
Read only
Status
Mandatory
{iccPortEntry 2}
Description
Optional database entry used to identify individual circuits. When a port name is used, each one should be unique and descriptive of port usage. This object accepts up to 8 upper- or lowercase alphanumeric characters.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.2
Data Type
DisplayString (size 0...8)
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 3}
Description
Determines the signaling type. Possible values include:
| Value | Meaning |
|---|---|
eAndm | E&M |
fxo-ls | FXO Loop Start |
fxo-gs | FXO Ground Start |
fxs-ls | FXS Loop Start |
fxs-gs | FXS Ground Start |
clear | Clear Channel |
ieAndm | Inverted E&M |
userDefX | User Defined where: FXO = Foreign Exchange Office FXS = Foreign Exchange Subscriber |
 |
Note If you selected an SF_NR or ESF_NR span type, this object is ignored. |
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.3
Data Type
Integer. Possible values are as follows:
| Value | String |
|---|---|
1 | eAndm |
2 | fxo-ls |
3 | fxo-gs |
4 | fxs-ls |
5 | fxs-gs |
6 | clear |
7 | ieAndm |
8 | userDef1 |
9 | userDef2 |
10 | userDef3 |
11 | userDef4 |
12 | userDef5 |
13 | userDef6 |
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 4}
Description
Class of Service used for resource grouping and B-channel allocation; determines the software operating characteristics for this port. Different spans on the same card can have different COS marks. Possible values and their meanings are listed in the following table:
| Value | Meaning |
|---|---|
o | Originating—Calls originating from the VCO; outgoing calls initiated by host command |
t | Terminating—Calls terminating at the VCO; incoming calls initiated by actions outside the SDS/VCO or forced by host command |
w2 | 2-Way—Calls originating from the VCO or calls terminating at the SDS/VCO; outgoing calls initiated by host command, incoming calls initiated by outside actions |
oa | Always Off Hook and Originating—Calls originating from the SDS/VCO, port goes off hook at VCO system reset and remains off hook; outgoing calls initiated by host command |
ta | Always Off Hook and Terminating—Calls terminating at the SDS/VCO, port goes off hook at VCO system reset and remains off hook; incoming calls initiated by outside actions or forced by host command |
a2 | Always Off Hook and 2-Way—Calls originating from the SDS/VCO or calls terminating at the VCO, port goes off hook at SDS/VCO system reset and remains off hook; outgoing calls initiated by host command, incoming calls initiated by outside actions or forced by host command |
|
Note Internal COS values, i.e., U2 (2-way currently used as an outgoing) and T2 (2-way currently used as an incoming), may appear during system operation. These values are internal processing representations and cannot be assigned. |
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.4
Data Type
Integer. Possible values are as follows:
| Value | String |
|---|---|
0 | none |
1 | o |
2 | t |
3 | w2 |
4 | oa |
5 | ta |
6 | a2 |
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 13}
Description
The major state of the port.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.13
Data Type
PortMajorState
Access Policy
Read only
Status
Mandatory
{iccPortEntry 14}
Description
The supplementary state of the port.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.14
Data Type
PortSuppState
Access Policy
Read only
Status
Mandatory
{iccPortEntry 15}
Description
Specifies the software address (hexadecimal identifier) of the port for which data is displayed. The port can also be specified by the hardware address.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.15
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccPortEntry 16}
Description
This is a foreign key corresponding to the inpulseRuleIndex in the inpulseTable. It is accessed while assigning a particular inpulse rule to a port. Determines the inpulse rule processed when this port goes off hook. Default inpulse rules are used for incoming ports only (Class of Service = T, W2, AT, or A2). The inpulse rule must be defined from the Inpulse Rules Table screens.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.16
Data Type
InpulseRuleIndex
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 17}
Description
Indicates the number of the resource group to which this port belongs. In order to change this attribute, you need to set this EntryStatus and the one in the resGroupTable to underModification.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.17
Data Type
ResGroupIndex
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 18}
Description
Specifies the position of the port in the assigned resource group.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.18
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{iccPortEntry 19}
Description
Registers the last error that occurred on this port entry.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.19
Data Type
Integer ( invalidValue = 6656 )
Access Policy
Read only
Status
Mandatory
{iccPortEntry 20}
Description
The entity that configured this entry and is therefore using the resources assigned to it.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.20
Data Type
OwnerString
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 21}
Description
The status of this table entry.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.21
Data Type
PortEntryStatus
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 22}
Description
The state of port can be changed to active or inactive. 1= active; 2 = inactive.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.22
Data Type
Integer
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 23}
Description
Specifies the type of icc card to which this port belongs. Same as iccType.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.23
Data Type
Integer. Possible values are as follows:
| Value | String |
|---|---|
1 | nxT1 |
2 | nxE1 |
3 | t1IsdnPriNi2 |
4 | t1IsdnPri5Ess |
5 | t1IsdnPri4Ess |
6 | t1IsdnPriNti |
7 | t1IsdnPriNtt |
8 | e1IsdnPriNet5 |
9 | e1IsdnPriQsig |
10 | e1IsdnPriTs014 |
Access Policy
Read only
Status
Mandatory
{iccPortEntry 24}
Description
Only valid when iccPortCardType is one of the non-ISDN types, i.e., nxT1 or nxE1. When iccPortCardType is one of the ISDN flavors, a get on this object will return 0 and a set on this object will result in an error.
Indicates the voice coding on the stream. The system automatically turns off translation when calls specify unrestricted digital information bearer capability.
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.24
Data Type
Integer. Possible values are as follows:
| Value | String |
|---|---|
1 | a |
2 | mu |
3 | system |
Access Policy
Read-write
Status
Mandatory
{iccPortEntry 25}
Description
Only valid when iccPortCardType is one of the ISDN types. When iccPortCardType is not one of the ISDN flavors, a get on this object will return 0 and a set on this object will result in an error.
Specifies the ISDN port state.
Possible values are as follows:
| Value | Meaning |
|---|---|
in-serv | The port is currently in service and available for use in a call. |
oos-ne | Out-of-Service, Near-End. Port is currently out-of-service due to some VCO action (system administration). Port is unavailable to call processing. SDS/VCO action is required to put it back into service. |
oos-fe | Out-of-Service, Far-End. Port is currently Out-of-service due to some action at the far-end. Port is unavailable to call processing. Action at the far end is required to put it back into service. |
maint-ne | Maintenance, Near-End. Port is currently in Maintenance mode due to some SDS/VCO action (system administration) or signal alarm condition. Port is unavailable to call processing. |
maint-fe | Maintenance, Far-End. Port is currently in Maintenance mode due to some action at the far end. Port is unavailable to call processing. Action at the far end is required to put the port back into service. |
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.25
Data Type
Integer. Possible values are as follows:
| Value | String |
|---|---|
1 | in-serv |
2 | oos-ne |
3 | oos-fe |
4 | maint-ne |
5 | maint-fe |
Access Policy
Read only
Status
Mandatory
{iccPortEntry 26}
Description
Only valid when iccPortCardType is one of the ISDN types. When iccPortCardType is not one of the ISDN flavors, a get on this object will return 0 and a set on this object will result in an error.
This specifies the isdn-call state of the call on the port. The description of each call state is as follows:
| Value | User-side call state |
|---|---|
idle | NULL state (U0/Rest 0) |
o-inited | Call Initiated (U1) |
i-overlap OR o-overlap | Overlap Sending (U2)—Reserved for future use |
o-proceed | Outgoing Call Proceeding (U3) |
o-delivrd | Call Delivered (U4) |
i-callprs | Call Present (U6) |
i-receivd | Call Received (U7) |
i-connect | Connect Request (U8) |
i-proceed | Incoming Call Proceeding (U9) |
i-active OR o-active | Active (U10) |
disc-req | Disconnect Request (U11) |
disc-ind | Disconnect Indication (U12) |
disc-rls | Release Request (U19)" |
Object Identifier
1.3.6.1.4.1.886.1.12.4.1.26
Data Type
Integer. Possible values are as follows:
| Value | String |
|---|---|
0 | unknown |
1 | idle |
2 | o-inited |
3 | o-overlap |
4 | o-proceed |
5 | o-active |
6 | o-delivrd |
7 | i-callprs |
8 | i-overlap |
9 | i-proceed |
10 | i-active |
11 | i-receivd |
12 | i-connect |
13 | disc-ind |
14 | disc-req |
15 | disc-rls |
Access Policy
Read only
Status
Mandatory
{icc 5}
Description
The time (in hundredths of a second) since the epoch that the iccPortTable was last modified.
Object Identifier
1.3.6.1.4.1.886.1.12.5
Data Type
TimeTicks
Access Policy
Read only
Status
Mandatory
Posted: Sat Sep 28 11:08:58 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.