cc/td/doc/product/software/ios124/124relnt
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table Of Contents

Release Notes for Cisco IAD2430 Series Integrated Access Devices with Cisco IOS Release 12.4(11)XW

Contents

Introduction

Cisco 2430 Series Integrated Access Device

System Requirements

Memory Requirements

Hardware Supported

Determining the Software Version

Upgrading to a New Software Release

Feature Set Tables

New and Changed Information

New Hardware Features in Cisco IOS Release 12.4(11)XW6

New Software Features in Cisco IOS Release 12.4(11)XW6

New Hardware Features in Cisco IOS Release 12.4(11)XW5

New Software Features in Cisco IOS Release 12.4(11)XW5

New Hardware Features in Cisco IOS Release 12.4(11)XW3

New Software Features in Cisco IOS Release 12.4(11)XW3

New Hardware Features in Cisco IOS Release 12.4(11)XW2

New Software Features in Cisco IOS Release 12.4(11)XW2

New Hardware Features in Cisco IOS Release 12.4(11)XW1

New Software Features in Cisco IOS Release 12.4(11)XW1

New Hardware Features in Cisco IOS Release 12.4(11)XW

New Software Features in Cisco IOS Release 12.4(11)XW

New Features in Release 12.4T

Limitations and Restrictions

Caveats

Open Caveats - Cisco Release 12.4(11)XW6

Resolved Caveats - Cisco Release 12.4(11)XW6

Open Caveats - Cisco Release 12.4(11)XW5

Resolved Caveats - Cisco Release 12.4(11)XW5

Open Caveats - Cisco Release 12.4(11)XW3

Resolved Caveats - Cisco Release 12.4(11)XW3

Open Caveats - Cisco Release 12.4(11)XW2

Resolved Caveats - Cisco Release 12.4(11)XW2

Open Caveats - Cisco IOS Release 12.4(11)XW1

Resolved Caveats - Cisco IOS Release 12.4(11)XW1

Open Caveats - Cisco IOS Release 12.4(11)XW

Resolved Caveats - Cisco IOS Release 12.4(11)XW

Additional References

Release-Specific Documents

Platform-Specific Documents

Cisco Feature Navigator

Cisco IOS Software Documentation Set

Obtaining Documentation, Obtaining Support, and Security Guidelines


Release Notes for Cisco IAD2430 Series Integrated Access Devices with Cisco IOS Release 12.4(11)XW


First Released: May 4, 2007
Last Revised: February 4, 2008
Cisco IOS Release 12.4(11)XW6
OL-13462-07 Fifth Release

These release notes for the Cisco IAD2430 Series Integrated Access Devices (IAD) describe the product-related enhancements provided in Cisco IOS Release 12.4(11)XW. These release notes are updated as needed.

For a list of the software caveats that apply to Cisco IOS Release 12.4(11)XW, see "Caveats" section. See also Caveats for Cisco IOS Release 12.4T , which is updated for every maintenance release and is located on Cisco.com.

Use these release notes with Cross-Platform Release Notes for Cisco IOS Release 12.4T located on Cisco.com.

We recommend that you view the field notices for this release to see if your software or hardware platforms are affected. If you have an account on Cisco.com, you can find field notices at http://www.cisco.com/warp/customer/tech_tips/index/fn.html. If you do not have a Cisco.com login account, you can find field notices at http://www.cisco.com/warp/public/tech_tips/index/fn.html.

Contents

These release notes describe the following topics:

Introduction

System Requirements

New and Changed Information

Limitations and Restrictions

Caveats

Additional References

Obtaining Documentation, Obtaining Support, and Security Guidelines

Introduction

The Cisco IAD2430 is the next generation integrated voice and data services platform for Service Providers, building on the industry leading Cisco IAD2420 series IAD. The Cisco IAD2430 series offers a major leap forward in price performance and enhanced software functionality such as MGCP SRST used to accelerate the migration from time division multiplexing (TDM) to VoIP cost efficiently. The Cisco IAD2430 series harnesses the maturity of the Cisco IAD2420 series software and enhances functionality by providing more capabilities such as denser interfaces (up to 24 FXS and up to 2 voice or 2 data T1s), encryption, and DC power back up while maintaining it's 1RU form factor for space saving Service Provider Managed Services deployment.

For information on new features and Cisco IOS commands supported by Cisco IOS Release 12.4(11)XW, see the "New and Changed Information" section.

Cisco 2430 Series Integrated Access Device

The Cisco IAD2430 Series Integrated Access Device consists of the following five models:

Cisco 2430-24FXS IAD

Cisco 2431-8FXS IAD

Cisco 2431-16FXS IAD

Cisco 2431-1T1E1 IAD

Cisco 2432-24FXS IAD

The following WAN interface cards (WICs) and Voice Interface Cards (VICs) are supported:

VIC2-2FXO

VIC2-2FXS

VIC-4FXS/DID

VIC2-2BRI-NT/TE

VWIC-2MFT-T1

VWIC-2MFT-E1

WIC-1T

WIC-1ADSL

WIC-1SHDSL

WIC-1ADSL-DG

WIC-1SHDSL-V2

Port Numbering

Port numbering conventions for the Cisco IAD2430 Series Integrated Access Device differs from the Cisco IAD2420 Series Integrated Access Device:

An external compact flash card is numbered slot 0.

10/100Base-T Fast Ethernet ports are numbered Fast Ethernet 0/0 and Fast Ethernet 0/1 from right to left.

T1/E1 ports are numbered T1 or E1 1/0 and T1 or E1 1/1 from right to left.

The slot for WICs and VICs is numbered slot 0. WIC and VIC interfaces are numbered by interface face with this slot number and an interface number, beginning with 0 and running from right to left.

FXS voice port numbering begins at 2/0 and extends to 2/7, 2/15, or 2/23, depending on the number of voice ports.

MGCP Endpoint Naming Convention

The Media Gateway Control Protocol (MGCP) endpoint naming convention for Cisco IAD2430 Series IAD differs from the Cisco IAD2420 Series IAD. The MGCP naming convention for the Cisco IAD2430 Series IAD is the following:

Cisco IAD2431-1T1E1

S1/DS1-0/1@iad2430-digital
S1/DS1-0/2@iad2430-digital
. . .
S1/DS1-0/24@iad2430-digital

S1/DS1-1/1@iad2430-digital
S1/DS1-1/2@iad2430-digital
. . .
S1/DS1-1/24@iad2430-digital

Cisco IAD2430-24FXS, IAD2431-8FXS, IAD2431-16FXS, IAD2432-24FXS

AALN/S2/0@iad2430-analog
AALN/S2/1@iad2430-analog
. . .
AALN/S2/23@iad2430-analog

Voice Analog Ports

AALN/S0/0@iad2430-analog
AALN/S0/1@iad2430-analog
AALN/S0/2@iad2430-analog
AALN/S0/3@iad2430-analog

System Requirements

This section describes the system requirements for the Cisco IOS Cisco IOS Release 12.4(11)XW releases and includes the following sections:

Memory Requirements

Hardware Supported

Determining the Software Version

Upgrading to a New Software Release

Feature Set Tables

Memory Requirements

Table 1 lists the memory recommendations of the Cisco IOS feature sets for the Cisco IAD2430 series IAD for Cisco IOS Release 12.4(11)XW. Cisco IAD2430 series IAD are available with a 32-MB Flash memory card.

Table 1 Cisco Release 12.4(11)XW Memory Recommendations for the Cisco IAD2430 Series IAD 

Platform
Feature Set
Software Image
Recommended
Flash
Memory (MB)
Recommended
DRAM
Memory (MB)
Runs
From

Cisco IAD2430

Cisco 2430 Series IOS IP Subset/IPSEC 64BIT/FW/Voice

c2430-i6k9o3s-mz

64

128

RAM

Cisco 2430 Series IOS IP Subset/Voice

c2430-i6s-mz

64

128

RAM

Cisco IAD2431- Cisco IAD2432

Cisco 2430 Series IOS IP Plus/IPsec 64BIT/FW/Voice

c2430-ik9o3s-mz

64

128

RAM

Cisco 2430 Series IOS IP Plus

c2430-is-mz

64

128

RAM


Hardware Supported

Cisco IOS Release 12.4(11)XW supports the following platforms:

Cisco IAD2430

Cisco IAD2431

Cisco IAD2432

For detailed descriptions of the new hardware features, see the "New and Changed Information" section.

For information about supported hardware for this platform and release, see the Hardware/Software Compatibility Matrix in the Cisco Software Advisor at the following location:

http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi

Determining the Software Version

To determine which version of Cisco IOS software is currently running on your Cisco 2430, log in to the router and enter the show version EXEC command. The following sample output from the show version command indicates the version number.

Router> show version
Cisco Internetwork Operating System Software
IOS (tm) C2430 Software (c2430-is-mz), Version 12.4(11)XW, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.4(11)T

Upgrading to a New Software Release

For general information about upgrading to a new software release, see the Software Installation and Upgrade Procedures located at http://www.cisco.com/warp/public/130/upgrade_index.shtml.

Feature Set Tables

The Cisco IOS software is packaged in feature sets consisting of software images, depending on the platform. Each feature set contains a specific set of Cisco IOS features. Cisco IOS Release 12.4(11)XW supports the same feature sets as Releases 12.4 and 12.4(11)T, but Cisco IOS Release 12.4(11)XW includes new features supported by the Cisco 2430 IAD.


Caution The Cisco IOS images with strong encryption (including, but not limited to, 168-bit [3DES] data encryption feature sets) are subject to United States government export controls and have limited distribution. Strong encryption images to be installed outside the United States will likely require an export license. Customer orders can be denied or subject to delay as a result of United States government regulations. When applicable, the purchaser/user must obtain local import and use authorizations for all encryption strengths. Contact your sales representative or distributor for more information, or send an e-mail to export@cisco.com.

Table 2 lists the feature and feature sets supported in the Cisco IOS Cisco IOS Release 12.4(11)XW releases.

The tables use the following conventions:

In: The number in the `In' column indicates the Cisco IOS release in which the feature was introduced. For example, "12.4(11)XW" indicates that the feature was introduced in 12.4(11)XW. If a cell in this column is empty, the feature was included in a previous release or in the initial base release.

Yes: The feature is supported in the software image.

No: The feature is not supported in the software image.


Note These feature set tables contain only a selected list of features, which are cumulative for Release 12.4(11)nn early deployment releases only (nn identifies each early deployment release). The tables do not list all features in each image: additional features are listed in Cross-Platform Release Notes for Cisco IOS Release 12.4(11)T and Release 12.4(11)T Cisco IOS documentation.


Table 2 Feature List for Cisco IAD2430 Series Integrated Devices

Feature
In
Feature Set
IP/ADSL/VOX PLUS

"Voice Quality Enhancements"

12.4(11)XW

See Table 1 for image names.


New and Changed Information

The following sections list the new hardware products and software features supported by the Cisco IAD2430 series IAD in Cisco IOS Release 12.4(11)XW:

New Hardware Features in Cisco IOS Release 12.4(11)XW6

New Software Features in Cisco IOS Release 12.4(11)XW6

New Hardware Features in Cisco IOS Release 12.4(11)XW6

New Software Features in Cisco IOS Release 12.4(11)XW5

New Hardware Features in Cisco IOS Release 12.4(11)XW3

New Software Features in Cisco IOS Release 12.4(11)XW3

New Hardware Features in Cisco IOS Release 12.4(11)XW2

New Software Features in Cisco IOS Release 12.4(11)XW2

New Hardware Features in Cisco IOS Release 12.4(11)XW1

New Software Features in Cisco IOS Release 12.4(11)XW1

New Hardware Features in Cisco IOS Release 12.4(11)XW

New Software Features in Cisco IOS Release 12.4(11)XW

New Features in Release 12.4T

New Hardware Features in Cisco IOS Release 12.4(11)XW6

There are no new hardware features in this release.

New Software Features in Cisco IOS Release 12.4(11)XW6

There are no new software features in this release.

New Hardware Features in Cisco IOS Release 12.4(11)XW5

There are no new hardware features in this release.

New Software Features in Cisco IOS Release 12.4(11)XW5

There are no new software features in this release.

New Hardware Features in Cisco IOS Release 12.4(11)XW3

There are no new hardware features in this release.

New Software Features in Cisco IOS Release 12.4(11)XW3

There are no new software features in this release.

New Hardware Features in Cisco IOS Release 12.4(11)XW2

There are no new hardware features in this release.

New Software Features in Cisco IOS Release 12.4(11)XW2

Cisco Unified Communications Manager Express 4.2

Media Encryption (SRTP) on Cisco Unified Communications Manager Express feature provides the following secure voice call capabilities: Secure call control signaling and media streams in Cisco Unified Communications Manager Express (Unified CME) networks using Secure Real-Time Transport Protocol (SRTP) and H.323 protocols.

1. Secure call control signaling and media streams in Cisco Unified Communications Manager Express (Unified CME) networks using Secure Real-Time Transport Protocol (SRTP) and H.323 protocols.

2. Secure supplementary services for Unified CME networks using H.323 trunks.

3. Secure Cisco VG224 Analog Phone Gateway endpoints.

For more information on this feature, go to:

http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124newft/124limit/124x/124xw11/itseccme.htm

New Hardware Features in Cisco IOS Release 12.4(11)XW1

There are no new hardware features in this release.

New Software Features in Cisco IOS Release 12.4(11)XW1

There are no new software features in this release.

New Hardware Features in Cisco IOS Release 12.4(11)XW

There are no new hardware features in this release.

New Software Features in Cisco IOS Release 12.4(11)XW

The following new software features are supported in this release:

Voice Quality Enhancements

Voice Quality Enhancements

DSP voice quality metrics improve your ability to monitor, analyze, and ultimately meet your quality of service (QoS) objectives for your network. For more details, go to:

http://www.cisco.com/en/US/products/ps6706/products_feature_guide09186a0080756fd1.html

New Features in Release 12.4T

For information regarding the features supported in Cisco IOS Release 12.4T, see the Cross-Platform Release Notes and New Feature Documentation links at the following location on Cisco.com: http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124relnt/xprn124/index.htm 

Limitations and Restrictions

There are no known limitations or restrictions in this release.

Caveats

Caveats describe unexpected behavior or defects in the Cisco IOS software releases. Severity 1 caveats are the most serious caveats, severity 2 caveats are less serious, and severity 3 caveats are the least serious of these three severity levels.

Caveats in Cisco IOS Release 12.4(11)T are also in Cisco IOS Release 12.4(11)XW. For information on caveats in Cisco IOS Release 12.4(11)T, see the Caveats for Cisco IOS Release 12.4(11)T document. This document lists severity 1 and 2 caveats; the documents are located on Cisco.com.


Note If you have an account with Cisco.com, you can also use the Bug Toolkit to find select caveats of any severity. To reach the Bug Toolkit, log in to Cisco.com and go to: http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. 


This section contains the following caveat information:

Open Caveats - Cisco Release 12.4(11)XW6

Resolved Caveats - Cisco Release 12.4(11)XW6

Open Caveats - Cisco Release 12.4(11)XW6

Resolved Caveats - Cisco Release 12.4(11)XW5

Open Caveats - Cisco Release 12.4(11)XW3

Resolved Caveats - Cisco Release 12.4(11)XW3

Open Caveats - Cisco Release 12.4(11)XW2

Resolved Caveats - Cisco Release 12.4(11)XW2

Open Caveats - Cisco IOS Release 12.4(11)XW1

Resolved Caveats - Cisco IOS Release 12.4(11)XW1

Open Caveats - Cisco IOS Release 12.4(11)XW

Resolved Caveats - Cisco IOS Release 12.4(11)XW

Open Caveats - Cisco Release 12.4(11)XW6

There are no open caveats in this release.

Resolved Caveats - Cisco Release 12.4(11)XW6

CSCsk61275 no ring on 7941 phone while hunting second overlay number

Symptom    The Cisco Unified IP Phone 7941 does not ring while hunting the second overlay number in Call Forward No Answer (CFNA) configuration.

Conditions   Overlay button is configured on Cisco 7941, and CFNA is configured from the first number to the second number.

Workaround   Use Cisco IOS Release 12.4(11)XJ3 or Cisco IOS Release 12.4(11)T3.

CSCsk09132 Hotice router crashed with debug parser before-after and session-server

Symptom    The router crashes when the maximum permissible number of session-servers are configured for a voice register dn with the command 'session-server 1 2 3 4 5 6 7 8'.

Conditions   A voice register dn should be configured.

Workaround   This symptom can be worked around if one less than the number of maximum session-servers are configured. 'session-server 1 2 3 4 5 6 7 ' should solve this problem if it occurs.

CSCsj81015 IPIP Gateway crash ccsip_bridge

Symptom    Cisco Multiservice IP-to-IP Gateway (IPIPGW) crashes during a stress scenario.

Conditions   This symptom occurs in a stress scenario with 100 SIP-H323 calls + 150 SIP-H323 DTMF interworking (rtp-nte to h245-alpha) calls.

Workaround   There is no workaround.

CSCsk42299 IPIPGW h323 no H.245 TCS with FS-SS interwork call to CCM

Symptom    Cisco IPIPGW does not establish TCP connection for H.245 on the TCP port suggested by Cisco Unified CallManager (CCM).

Conditions   The IPIPGW is configured for FS-to-SS interworking. In CCM, the "Wait for Far-End H.245 Terminal Capability Set" option is unchecked.

Workaround   There is no workaround.

CSCsj27183 Transcoding: Call fails for H323--SIP Fast start call

Symptom    H323-->SIP interworking fails for a Fast start call when transcoding is enabled on an IPIPGW. Transcoding is done between G711ulaw and G729r8 codecs.

Conditions   This failure is seen for H323--SIP--SIP--SIP and H323--SIP--SIP--H323 call flows when transcoding is enabled on IPIPGW1. It is also seen on H323--H323--H323--SIP call flow for transcoding on IPIPGW2. This is seen only with a Fast Start call (both with H245 Tunnel enabled and disabled), and the call passes with a slow start call.

Workaround   There is no workaround.

CSCsl53327 max-ephones and max-dn show wrong range on UC520-48U-SKU.

Symptom    max-ephones and max-dn show wrong range on UC520-48U-SKU

Conditions   This symptom occurs only if the FLU variable is changed.

Workaround   Do not change the FLU variable.

CSCsl79588 Router crashes after changing the MOH

Symptom    Router running Cisco IOS may crash with a bus error.

Conditions   The router must be configured to stream MOH (Music-on-Hold) from a .wav file with a header longer than 256 bytes.

Workaround   Do not use ".wav" files for Music-on-Hold. Use only ".au" files.

CSCsm20994 kron job daily reoccurrences fail after new year

Symptom    kron occurrences are not rescheduled properly when the clock is set near the end of a calendar year.

Conditions   A kron occurrence is scheduled daily or hourly. The clock is reset near the end of the year such that the next occurrence of the kron policy would happen in the next year.

Workaround   After clock reset, remove/restore kron occurrences to cause them to be scheduled properly.

Open Caveats - Cisco Release 12.4(11)XW5

There are no open caveats in this release.

Resolved Caveats - Cisco Release 12.4(11)XW5

CSCsk45804 CME speeddials fails after attempting to invalid number

Symptom    Pressing a speeddial button on CME does nothing.

Conditions   Previously, a speeddial was used to target an unavailable/non-existent number.

Workaround   Connect a normal call on the problematic phone.

CSCsk65748 If POE 48V fails to come up, we need to retry 3 times CSCsk60054 Configuration buffer full. Cannot display show run

Symptom    When certain configuration changes, the running configuration might not be able to be displayed and the following error message might appear:

% Configuration buffer full, can't add command: !
%Aborting Save. Compress the config, Save it to flash or Free up space on device

Conditions   The issue is seen either using or not using service compress-config on a Cisco IOS Router running CallManager Express (CME) when configuring more than 22 voice user-profiles.

Workaround   There is no workaround.

CSCsk31644 Spurious Access at cmm_crs_proc_tr_call_consult_resp

Symptom    Spurious memory access is seen while executing call forward scenarios.

Conditions   This is seen on c3845 while executing CME and UCCX related test scenarios.

Workaround   There is no workaround.

CSCsk55078 CME 4.2 Diversion Header issue in chained supplementary service CSCsk22265 CME: 7935 and 7936 Corporate Directory Lookup fails in CME 4.1 and 4.2

Symptom    When attempting to use the Corporate Directory Lookup feature on a Cisco 7935 or 7936 Conference IP Phone, an attempt to search for matching records using a First Name or Last Name query results in the message "Server not found" being returned.

Conditions   This behavior is observed when the Cisco 7935 and 7936 Conference IP Phones are registered to a Cisco Unified Call Manager Express (CUCME) Voice Router installed with CUCME version 4.1 or newer (IOS 12.4(15)T train and newer, or 12.4(11)XJ and newer). The 7935 and 7936 IP Phones can be installed either with the approved SCCP Firmware Version 7.x or 8.x phone loads.

Workaround   (1) This problem is not observed in CUCME 3.3 (IOS 12.4 mainline) up to 4.0(2) (IOS 12.4(11)T3). If CUCME 4.1 features are not required use these older versions of CUCME. (2) Use a non-79x5 IP Phone registered to the same CUCME Voice Router to perform the Local Directory Search.

CSCsk50911 Need to update the max-ephones range for various platforms CSCsk25651 ephone-dn removal does not clean up mwi state

Symptom    With Cisco Unity Express (CUE) integrated to Cisco Unified Communication Manager (CUCM) / CallManager utilizing SRST functionality, when the IP phones are registered to the SRST router, the MWI states may be incorrect.

Conditions   When a phone registers to an SRST router, each directory number (DN) gets a particular ephone-dn number that will have a particular MWI state. If the phone unregisters from the SRST router and later re-registers to the router (possibly due to an intermittent connectivity to the CUCM), the ephone-dn number may be different since the ephone-dn numbers are assigned sequentially in a first-come-first-served fashion. The MWI state, however, is remembered from the previous registration that used the ephone-dn number so the MWI status could be incorrect.

Workaround   There is no workaround.

CSCsj53899 Remove xlate profile from voice register dn removes from dial-peer

Symptom    Removing voice xlate profile from a voice register dn results in the same xlate profile being removed from a dial-peer.

Conditions   Have the same xlate profile name under a voice register dn and dial-peer and using IOS 12.4(11)XW - XW2.

Workaround   There is no workaround.

CSCsj93762 Resume fails after HOLD for SIP phones regist with voice-class codec CSCsj81363 FRU incorrect and Carrier Set empty on wireless B sku platforms

Symptom    Under the show controller output for the Dot11 interface, the carrier set field is empty. This should say Americas. This does not affect functionality, all of the correct channels are present. Under the show diag output, the FRU says CISCO1811W-AG-A/K9 instead of CISCO1811W-AG-B/K9. This is just the labeling and does not affect functionality.

Conditions   This is seen with the B models of the 1800 wireless routers running 12.4(11)XW1.

Workaround   There is no workaround. This issue does not affect functionality.

CSCsk42889 SIP call xfer to voicemail fails with DNS Query failed error

Symptom    SIP trunk----CME/CUE AA---xfer extension---CFNA---CUE voicemail. Call transfers from AA to extension, CFNA back to CUE voicemail drop.

Conditions   CME running 12.4(11)XW3.

Workaround   There is no workaround.

CSCsk58359 Update max sip phone range for various platform CSCse14595 call may be connected while being cfna to an PSTN call

Symptom    CME allows call connect after CFNA timer expire. On the 3745 with IOS 12.4(5)a customer can pick up the phone and get connected to the calling party after the CFNA timer expire.

Conditions   When this problem is seen then there is a delay between Call-proc and Alerting messages from ISDN side.

Workaround   Use the longer CFNA timer or use the "application default.c.old".

CSCsk35315 CME: calledName= displayed garbled characters

Symptom    Display on Cisco IP Phone contains corrupted characters when placing outbound PSTN call on an ISDN circuit.

Conditions   A Cisco IP Phone placing an outbound ISDN call through a Cisco IOS gateway configured for Cisco Unified Communication Manager Express may experience at times the name displayed on the screen with unrecognizable characters once the call connects.

This can occur if there is an ISDN Facility message received after the call connects that does not contain display name information; for example an inbound facility message for Advice of Charge (AOC) may trigger this problem.

These messages can be seen on the gateway through the use of debug isdn q931. Caution should be taken when enabling any debugs on a production router/gateway as it can impact performance. Make sure as a minimum to disable console logging on the IOS device before enabling any debug. This issue does not have an impact to the operation or performance of the gateway nor phone.

Workaround   Contact the ISDN service provider to determine if the facility messages causing this problem can be disabled.

CSCsk16153 Modem won't be disconnected on exit

Symptom    Modem connection is still active on exit.

Conditions   After "exit" from modem session.

Workaround   There is no workaround.

CSCsk73035 dtmf stop working if using connection plar opx immediate on fxo port

Symptom    dtmf stop working if using connection plar opx immediate on fxo port.

Conditions   Cu is running 124-11.XW on uc520. the dtmf does not work in the following call flow:

pstn--fxo---gw--sip--cue AA

If removing "immediate" from the following config,
the dtmf works.

voice-port 0/1/0
connection plar opx immediate 111
caller-id enable

Workaround   Don't use "immediate" option for the "connection plar opx".

CSCsk46424 Authentication fails on main dot11 interface when xconnect configured CSCsk52683 System crashed when wireless client is trying to associate with AP

Symptom    System crashes when there are clients trying to associate with AP.

Conditions   When AAA authentication fails with mis-configuration in the system or the wireless client's password is given wrong to try to associate.

Workaround   Make sure the AAA configuration is setup correctly and the client password is configured correctly.

CSCsk17498 Per Port Storm-Control is broken CSCsj88854 Router crashes when a call is made from Remote Phone registered to CUCME

Symptom    A call made over a SIP trunk from a remote phone registered to Cisco Unified Call Manager Express 4.1 to a phone registered to a SIP proxy server results in router crash due to memory overrun.

Conditions   Phone call has to be from remote phone. MLPPP should be configured as the WAN link. SIP trunk also traverses the same WAN link.

Workaround   Remove the MLPPP.

CSCsj02456 HTTP PUT operation using copy command failed

Symptom    HTTP PUT operation using copy command failed.

Conditions   Failure is seen with HTTP PUT operation using copy command.

Workaround   There is no workaround.

CSCsk83795 call may be disconnected when resetting other ephone

Symptom    Call is disconnected when another ephone is reset or unregisters.

Conditions   The call on the ephone-dn shared by other phone as non monitor button is disconnected if it is reset or unregisters from the CCME.

Workaround   There is no workaround.

CSCsj14565 ACL = deny; sa request ignored when crypto local-address is dynamic

Symptom    After a reboot of the router, or sometimes during normal operation, an IPsec tunnel fails to initiate. When debug crypto ipsec is enabled, the following error can be seen in the debug output: IPSEC(sa_initiate): ACL = deny; sa request ignored.

Conditions   The router is running 12.4(12) or later, and a crypto map name local-address interface statement is present in the configuration, where interface is the name of an interface that has a dynamic IP address configured (e.g. ip address negotiated or ip address dhcp)

For example:
crypto map mycryptomap local-address Dialer0
interface Dialer0
ip address negotiated

Workaround   A short term workaround consists of removing the access-list used in the crypto map, and then adding it again. This will bring up the tunnel as soon as there is an interesting traffic, but the problem may occur again later. Remove the crypto map name local-address interface statement, if possible. Downgrade to a release earlier then 12.4(12).

CSCsk74181 SIP DO-DO - Basic Fax call fails

Symptom    Fax call fails for a SIP DO-DO call.

Conditions   When the CUBE receives a ReINVITE with fax params, it does not forward the same. Instead it sends a BYE and the call gets disconnected.

Workaround   There is no workaround.

CSCsl04993 uc520 devices does not get reload via SNMP

Symptom    Cisco Unified Communications Series Integrated Services routers are not reloaded through SNMP.

Conditions   Cisco Unified Communications Series Integrated Services routers (ISRs) are not reloaded using SNMP when you restore the device configuration. Cisco Monitor Manager sends a device-reload request to the device after configuration file is restored; however, Cisco Unified Communications 500 Series ISRs do not accept this request through SNMP.

Workaround   To work around this problem, reload the device manually after restoring the configuration file.

CSCsj56438 Crafted EAP Response Identity packet may cause device to reload

Symptom    This Cisco Bug ID identifies vulnerability in Cisco's implementation of Extensible Authentication Protocol (EAP) that exists when processing a crafted EAP Response Identity packet. This vulnerability affects several Cisco products that have support for wired or wireless EAP implementations.

This vulnerability is documented in the following Cisco bug IDs:

* Wireless EAP - CSCsj56438
* Wired EAP - CSCsb45696 and CSCsc55249

This Cisco Security Response is available at the following link: http://www.cisco.com/warp/public/707/cisco-sr-20071019-eap.shtml.

CSCsk66907 %SYS-3-CPUHOG: due to Skinny MOH Server process

Symptom    PU Hog due to Skinny MOH Server causing phones to unregister:

%SYS-3-CPUHOG: Task is running for (xxx)msecs, more than (xxx)msecs
(xxxxxx),process = Skinny MOH Server.x

Conditions   Occurs if Music on Hold (MOH) is being streamed from flash in IOS 12.4(11)XW3.

Workaround   Use the live feed option by plugging in a CD player or iPOD or any such device to the MOH port on the UC500. Disable MOH from flash that implies tone on hold (or beep on hold).

CSCsi60392 CME does not send SIP NOTIFY DTMF to CUE-AA after txfer from CUE-VM

Symptom    No response to DTMF inputs during Auto Attendant session.

Conditions   Remote caller (across SIP Trunk) leaves voice message on local subscriber's CUE and then gets transferred to local AA. AA requests DTMF input for prompts played but this is not detected by CUE.

Workaround   There is no workaround.

CSCsl12443 CME: TNP phones may experience one way audio

Symptom    IP phone with FXO trunk config may experience intermittent one way audio. Debug ephone detail will show the following error:

OpenReceiveChannelAck status orcError on socket

Workaround   Reboot the phone.

CSCsj38652 Freddo DTMF/cptone issues for Taiwan, Hong Kong, Singapore Compliance

Symptom    DTMF levels are 0.3-0.5 dB below minimum limits for DTMF high/low tone signal power for Taiwan, Hong Kong and Singapore.

Conditions   This causes under normal conditions.

Workaround   Setting the cptone on the voice port to Singapore cures the problem.

CSCsk83813 sip call will pick up the wrong codec type from voice class codec

Symptom    When a SIP call is established, the Cisco IOS correctly uses the "codec preference 2" setting (G.711ulaw) that is configured in the voice class codec configuration. When this problem occurs, the tone remote control functionality does not work and voice becomes distorted due to the codec mismatch.

Conditions   A SIP call consistently uses the incorrect codec type from the "voice class codec" configuration. It should use the value that is configured for "codec preference 1," instead it uses the value that is configured for the "codec preference 2" setting. This issue occurs when the following configuration is used:

voice class codec 1
codec preference 1 g729r8
codec preference 2 g711ulaw

dial-peer voice 9191916 pots
description #1/1:16#0# INUSE 163
destination-pattern 19900001429191916
port 1/1:16

dial-peer voice 555 voip
rtp payload-type lmr-tone 107
rtp payload-type nte-tone 108
voice-class codec 1
session protocol sipv2
incoming called-number.
dtmf-relay rtp-nte
no vad

Using 2811
Cisco IOS versions: 12.4(17.4)PI1b and 12.4(17.4)PI1a

Workaround   There is no workaround.

CSCsk63037 CME 4.2 has broken caller ID feature

Symptom    Calling name is corrupted for ISDN calls on CME.

Conditions   The problem can be seen for every call.

Workaround   There is no workaround.

CSCsk95708 10 to 30 sec delay in starting media in secure meet-me conference

Symptom    SCCP messages are delayed by a few seconds for secure calls, this could effect secure dspfarm secure analog endpoints.

Conditions   Using secure dspfarm or analog endpoints.

Workaround   There is no workaround.

CSCsk42180 Few Objects of CISCO-LICENSE-MGMT-MIB giving wrong values during SNMP wa CSCsj94818 C877: ADSL2+ AnnexM: PVC goes to INAC after QoS is applied

Symptom    On C877 device for VC which is configured with vbr-nrt and PCR rate higher that VC bandwidth, when changes are introduced (e.g. QoS applied), VC goes in INAC status due to the fact that PCR is higher than physical bandwidth.

Conditions   Problem is seen on C877 device with ADSL2+ and with SW releases 12.4(11)XJ3 and 12.4(15)T1.

Workaround   Resetting VC resolve issue.

CSCsk06443 SIP TGW sends 183 response even though no response from ISDN

Symptom    IOS Gateway is sending 183 Response upon receiving retransmission of Invite Request.

Conditions   IOS GW has sent 100 trying response to original Invite Request and the call is in progress on other leg. Other leg could be either PSTN OR IP.

Workaround   There is no workaround.

CSCsk36600 Router crashes when ExtACL has mixed of tcp host and tcp net with QoS

Symptom    Router might crash when Extended ACL is applied with mixed of tcp permit statements with host and networks and this acl is applied in the class-map.

Conditions   The crash is seen when QOS with this Extended ACL is configured first and ACL statements are defined later.

Workaround   Configure permitted host statements successively and do the same for permitted networks. Configure ACL statements first and attach this ACL to class-map later.

CSCsj80906 Router crashes on changing ACL linked to service policy

Symptom    A Cisco router may crash due to a bus error.

Conditions   This has been experienced on multiple Cisco router platforms running IOS release 12.4(15)T1. The crash can occur if an access-list linked to a service-policy is removed, or if a service-policy is removed on an interface.

Workaround   There is no workaround.

CSCsl17037 CME: Local Directory Issue

Symptom    Directory numbers that are configured in local directory of CME are not being shown in received calls directory. The number and name shows while call in ringing state but is not showing during connected state.

Conditions   This is seen in Inbound call.

Workaround   There is no workaround.

CSCsl04115 CM call to CME when Put on Hold, CME Hears FastBusy instead of TOH

Symptom    Cisco IP Phone placed on hold hears fast busy instead of tone-on-hold.

Conditions   A Cisco IP Phone registered with a Cisco Unified CallManager Express (CME) may hear a fast busy tone when placed on hold. This can occur when interworking with Cisco Unified CallManager (CCM) as shown here:

IPPhoneA---CM---H323---CME---IpPhoneB

- Phone A calls Phone B
- Phone A puts Phone B on Hold.
- Instead of playing Tone On Hold, Phone B user hears a fast busy tone.

Workaround   This behavior was introduced in 12.4(15)T. Either downgrade the IOS version on the CUCME or configure music-on-hold (MOH) to be played from CUCM, instead of TOH.

CSCsk72582 Call in B-ACD drops if answered after hunting second time round

Symptom    Calls in B-ACD on CME router drops if the first round hunting is done through the hunt group lines. If the call is not answered, the caller is placed in the queue and hears an announcement with "all agents busy please hold " and so on. When the script hunts again after a timeout and this time, the call is answered, it drops the call completely. All phones in the hunt group will see a display of 1 call in queue for a few seconds before clearing.

Conditions   Call drops only after the 1st round of hunting. If the call is answered in the initial hunting, the call connects. Once the caller is in the queue and hears MOH, if the agent (hunt member) answers the call after that the call will drop.

Workaround   There is no workaround.

Open Caveats - Cisco Release 12.4(11)XW3

There are no open caveats in this release.

Resolved Caveats - Cisco Release 12.4(11)XW3

CSCsj97535 BACD functionality broken on freddo CSCsi50316 fix linux builds for rdo tools CSCsh74385 EEM fails to register with the redundancy framework (RF)

Symptom    It is not possible to configure event manager (EEM) applets for redundancyframework (RF) events:


nms-7206vxr(config)#event manager applet testapp
nms-7206vxr(config-applet)#event ?
application Application specific event
cli CLI event
counter Counter event
interface Interface event
ioswdsysmon IOS WDSysMon event
none Manually run policy event
oir OIR event
resource Resource event
snmp SNMP event
syslog Syslog event
timer Timer event
track Tracking object event

nms-7206vxr(config-applet)#

The keyword for RF is missing as EEM has not registered with RF.

Workaround   There is no known workaround.

CSCsj25470 EEM hostnames over 20 characters causes CLI actions to hang

Symptom    The Cisco Embedded Event Manager may hang and tie up virtual terminal (vty) lines if the devices host name is longer than 20 characters.

Conditions   The device has a hostname configured that is longer than 20 characters. The device has an Embedded Event Manager policy which uses the CLI actions or the CLI TCL library. The Embedded Event Manager policy enters configuration mode using the CLI actions or CLI TCL library.

Workaround   Use a hostname less than 20 characters.

Open Caveats - Cisco Release 12.4(11)XW2

There are no open caveats in this release.

Resolved Caveats - Cisco Release 12.4(11)XW2

CSCsg70474

Multiple voice-related vulnerabilities are identified in Cisco IOS software, one of which is also shared with Cisco Unified Communications Manager. These vulnerabilities pertain to the following protocols or features:

Session Initiation Protocol (SIP)

Media Gateway Control Protocol (MGCP)

Signaling protocols H.323, H.254

Real-time Transport Protocol (RTP)

Facsimile reception

Cisco has made free software available to address these vulnerabilities for affected customers. Fixed Cisco IOS software listed in the Software Versions and Fixes section contains fixes for all vulnerabilities mentioned in this advisory.

There are no workarounds available to mitigate the effects of any of the vulnerabilities apart from disabling the protocol or feature itself.

This advisory is posted at http://www.cisco.com/warp/public/707/cisco-sa-20070808-IOS-voice.shtml

CSCsi60004

Multiple voice-related vulnerabilities are identified in Cisco IOS software, one of which is also shared with Cisco Unified Communications Manager. These vulnerabilities pertain to the following protocols or features:

Session Initiation Protocol (SIP)

Media Gateway Control Protocol (MGCP)

Signaling protocols H.323, H.254

Real-time Transport Protocol (RTP)

Facsimile reception

Cisco has made free software available to address these vulnerabilities for affected customers. Fixed Cisco IOS software listed in the Software Versions and Fixes section contains fixes for all vulnerabilities mentioned in this advisory.

There are no workarounds available to mitigate the effects of any of the vulnerabilities apart from disabling the protocol or feature itself.

This advisory is posted at http://www.cisco.com/warp/public/707/cisco-sa-20070808-IOS-voice.shtml

CSCek78645 Analog phones cannot register with CME

Symptom    Analog phones when configured as SCCP phones cannot register with CCME.

Conditions   This happens under any normal conditions. If the phones are configured as SCCP endpoints, the phones will not register.

Workaround   There is no workaround.

CSCsj29857 xfer to ICD failed after conference AA

Symptom    Occurs when an incoming PSTN call to ICD is routed to an agent and the agent conferences AA. If the agent stays in the conference and tries to transfer the AA to ICD, the call sticks there.

Conditions   This happens to the incoming PSTN call when trying to transfer the AA to ICD during conferencing.

Workaround   This issue has been resolved. The solution is available in the release of CME (4.2)/12.4(11)XW2.

Open Caveats - Cisco IOS Release 12.4(11)XW1

There are no open caveats in this release.

Resolved Caveats - Cisco IOS Release 12.4(11)XW1

CSCsi13312 Authentication fails and unable to login to a factory fresh router

Symptom    Authentication with Security Device Manager (SDM) 2.3.3 fails, preventing you from logging into the router through HTTPS, HTTP, SSH, Telnet, console, or any management application.

Conditions   This symptom is observed on a Cisco router that is "fresh out of the box" and affects the following routers:

Cisco 800 series

Cisco 1700 series

Cisco 1800 series

Cisco 2700 series

Cisco 2800 series

Cisco 3700 series

Cisco 3800 series

Workaround   For extensive information and a workaround, see the following Field Notice:

http://www.cisco.com/en/US/products/ps5855/products_field_notice09186a0080809c8e.shtml

CSCsg62638 CPU usage reaches 99% after nmap scan on port 53

Symptom    Scan of a router when DNS server is enabled can cause high CPU usage of DNS process itself. Overall performance of the device can deteriorate to some extent.

Solution   The only way to rectify this situation is to reboot the device.

Workaround   There is no workaround. Cisco recommends upgrading to a fixed software release.

CSCsi56172 CME 4.1 IP phone dropped when trying to complete hardware conference

Symptom    IP phone trying to create an ad-hoc conference is dropped when pressing "Conf" softkey the second time.

Conditions   Must be using hardware conferencing in CME 4.1. The IP phone must receive a call first on on overlaid button. This initial call must come in on any DN besides the first DN configured in the "button" command in ephone configuration.

CSCsi58842 CME: 7960+7914 display select line when conference IP phone

Symptom   

1. A caller call a person "A".

2. Person "A" answer the call.

3. Person "A" is monitored by the person "B".

4. The person "B" see on his phone that the person "A" has received a call. Also person "B" calls person "A" using the monitor button.

5. Person "A" answers the call, putting the first caller on hold.

6. Person "A" uses the conference softkey "Confirm".

7. The message "Select Line" appears without any effect.

Workaround   There is no workaround.

Open Caveats - Cisco IOS Release 12.4(11)XW

There are no open caveats in this release.

Resolved Caveats - Cisco IOS Release 12.4(11)XW

CSCec12299 Corruption of ext communities when receiving over ipv4 EBGP session

Symptom    EIGRP-specific Extended Community 0x8800 is corrupted and shown as: 0x0:0:0.

Conditions   This symptom is observed when EIGRP-specific Extended Community 0x8800 is received via an IPv4 EBGP session on a CE router. This occurs typically in the following inter-autonomous system scenario:

ASBR/PE-1 <----> VRF-to-VRF <----> ASBR/PE-2

Workaround   Use a configuration such as the following to remove extended communities from the CE router:

router bgp 1
address-family ipv4 vrf one
neighbor 1.0.0.1 remote-as 100
neighbor 1.0.0.1 activate
neighbor 1.0.0.1 route-map FILTER in
exit-address-family
!
ip extcommunity-list 100 permit _RT.*_
!
!
route-map FILTER permit 10
set extcomm-list 100 delete
!
CSCek61570 Trunk dn stuck in seize/seize state and does not recover

Symptom    The ephone DN may get stuck in SEIZED state and one-way audio would occur afterwards.

Conditions   If another call is dropped during trunk dialing, the DN for this terminated call would move to seized state.

Workaround   Press ENDCALL softkey twice to move the seized DN to idle state after finishing the 2nd trunk call. To work around the one-way audio issue, the call needs to be transferred out and then transferred back. This workaround is not acceptable.

CSCek67866 xcodemsp.c Static Analysis Found Issue CSCek70830 $$TS: cme crashed during call to ICD routept running 124-11.3.4.PIA1 CSCsg36112 In xcoding, SCCP sessions not cleared immediately after abrupt call end

Symptom    When the calls are terminated/disconnected ungracefully or abruptly on an IPIP GW while doing large number of transcoding sessions, some of the sccp and rtp connection of that calls are not cleared immediately on IPIP Gw.

Conditions   This happens only when the transcoding calls on IPIP Gw are disconnected abruptly or ungracefully.

Workaround   There is no workaround.

CSCsg40567 Memory leak found with malformed tls/ssl packets in http core process

Symptom    Malformed SSL packets may cause a router to leak multiple memory blocks.

Conditions   This symptom is observed on a Cisco router that has the ip http secure server command enabled.

Workaround   Disable the ip http secure server command.

CSCsg69022 c1700 router crash @ nv_write_internal

Symptom    When a user configures the no telephony-service command, router crashes at running configuration generation.

Conditions   This symptom is highly unreproducible, but there is a potential race condition between the running configuration generation and the no telephony-service command.

Workaround   There is no workaround.

CSCsh65321 Phones fail to do secure authentication in 12.4(12.12)PI6

Symptom    Non-7921 phones will not register securely to CME.

Conditions   The cnf files for the non-7921 phones have their processNodeName field under CAPF server set to the CAPF IP address. A null value in this field will allow the phones to register securely.

Workaround   Remove the processNodeName parameter in the capf server of the phone's cnf file.

CSCsh73754 SmartPorts: PC connected to an IP phone cannot connect to WAN CSCsh80217 No Audio Path after REFER from xto to xee in a Meetingplace scenario

Symptom    No audio heard on Caller IP phone

Conditions   Meeting Place RSNA environment

Workaround   Yes Fallback image available

CSCsh81876 Traceback & crash if guest mode and multiple vlans

Symptom    In case the platform supported number of BSSIDs is 8 then configuring any ssid which comes in the 9th to 16th order in "sh run" as "guest-mode" results in a software crash. In general, if the platform supported BSSIDs considered as X and the maximum supported SSIDs considered as Y then configuring any ssid which comes in the X+1 to Y order(in "sh run") as "guest-mode" results in crash. Problem is not seen on platforms on which supported number of BSSIDs is 16.

Workaround   Configure only that ssid as "guest-mode" which comes in the order 1st to X(platform supported BSSIDs) in "sh run" i.e. if the number of platform supported BSSIDs is 8 then configure any ssid as "guest-mode" which comes in the order 1st to 8th in "sh run".

CSCsh89887 One way voice path with h/w conference on ephone-dn w/o preference 0 CSCsi03314 test ecdsa display-stats command not displaying output CSCsi04538 Router crash with memory corruption when configure cert-upgrade auth mod

Symptom    A CUCME (Cisco Unified Call Manager Express) router may crash with memory corruption when voice calls are made involving a transcoder.

Conditions   Voice calls should invoke a transcoder in order to see this crash.

Workaround   None

CSCsi09530 CME SIP phone failed to register because of authenticate register

Symptom    If "authenticate register" is configured under "voice register global", CME SIP failed to registered.

Conditions   "authenticate register" is configured under "voice register global", when CME is acting as a RIGISTRAR

Workaround   Disable "authenticate register" under "voice register global"

Further Problem Description   In registrar Functionality, CME challenges an inbound Register request with 401 response. If "authenticate register" is configured under "voice register global". The Registering Endpoint then Sends a Register Request with Crdentials. GW Stack is not processing this Request and is dropping it.

CSCsi15740 Memory leak in basic ICD call CSCsi22430 B-ACD Crashes CME 4.2

Symptom    CME could crash when running B-ACD script while call monitoring is enabled.

Conditions   CME could crash if (1) call monitoring is turned AND (2) an incoming call gets routed to any application scripts other than the Default Session.

Workaround   The work around is to manually disable callmon before running any non-default applications.

CSCsi27400 Memory leak in TGW for basic SRTP-TLS SIP call

Symptom    When a basic SIP call with SRTP using TLS is established between OGW and TGW, a memory leak is observed at the TGW.

Conditions   For all inbound calls(RTP/SRTP) where which SRTP and SIPS command is enabled.

Workaround   There is no workaround

CSCsi31667 SIP Registrations sent to Service Provider Proxy for Internal extentions CSCsi34163 Restore: Radar Detection for non-European regions. CSCsi42596 router crash when using MeetMe conference with 13 participants CSCsi44268 $$TS SIP trunk to AA to SIP phone disconnected

Problem Description    Call from sip-trunk to CRS/AA sip-phone, call disconnected after 19 seconds.

Symptom    The issues observed after V124_11_3_8_PI1A onwards. there was a major ida_t_pi1_atg sync to PI6 occurred in this label.

1. Two reINVITEs sent by originating gateway, received "500 Internal Server Error" on the 2nd reINVITE.

2. Terminating CME does not ACK on the reINVITE(unhold) received.

Root Cause    In Xfering_SetupDone() when case of CS_ACTIVE, remove calling AFW_Leg_Resume() again when handling special delayDisconnect call-info in REFER. This code is no longer needed since AFW now unhold the sip XEE before shelbourne hairpin.

Workaround   There is no workaround.

CSCsi44465 change CME version from 4.1 to 4.2

Symptom    Change CME product version from 4.1 to 4.2

Workaround   There is no workaround.

CSCsi44549 Router crashes during pings when QoS+NAT+FW+IPSEC+GRE are configured CSCsi47359 Crash seen in AFW_Process at the customer site CSCsi48062 H323--H323--SIP call fails with media transcoder high-density

Symptom    On the IPIPGW, an H.323-to-H.323 call fails to complete call setup.

Conditions   This problem happens when this call requires transcoding on the IPIPGW and media transcoder high-density is configured for use. Also, after TCS and MSD negotiation, only one of the OGW and TGW sides initiates the OLC negotiation, but not both.

Workaround   The workaround is not to use media transcoder high-density on the dial-peers which would handle such described interconnected calls.

CSCsi51441 uclient cannot ping to gateway via non-native vlan Please refer Release-note enclosure attached to the DDTS CSCsg58791. CSCsi52410 Add version 6.0 to the available CCM version on dspfarm CSCsi53006 Router crash in cmm_crs_proc_tr_call_trans_req

Symptom    CME with UCCX integration could crash at the following function:

cmm_crs_proc_tr_call_trans_req()

Conditions   The crash would only occur in very rare condition. Indeed the problem is difficult to reproduce. This could happen when an sccp endpoint attempts a consult transfer.

Workaround   There is no workaround.

CSCsi69819 Line protocol down when no auto speed and duplex negotiate on onboard FE

Additional References

The following sections describe the documentation available for the Cisco IAD2430. Typically, these documents consist of hardware and software installation guides, Cisco IOS configuration and command references, system error messages, feature modules, and other documents. Documentation is available as printed manuals or electronic documents, except for feature modules, which are available online on Cisco.com.

Use these release notes with the documents listed in the following sections:

Release-Specific Documents

Platform-Specific Documents

Release-Specific Documents

The following documents are specific to Release 12.4 and apply to Cisco IOS Release 12.4(11)XW. They are located on Cisco.com (under the heading Service & Support):

Cross-Platform Release Notes for Cisco IOS Release 12.4(11)T

Cisco IOS Release 12.4 Special and Early Deployments

http://www.cisco.com/en/US/products/ps6706/prod_release_notes_list.html

Caveats for Cisco IOS Release 12.4 and Caveats for Cisco IOS Release 12.4(11)T http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl


Note If you have an account with Cisco.com, you can also use the Bug Toolkit to find selected caveats of any severity. To reach the Bug Toolkit, log in to Cisco.com, and click Service & Support: Technical Assistance Center: Tool Index: Bug Toolkit. Another option is to go to http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl


Platform-Specific Documents

Hardware installation guides, configuration and command reference guides, and additional documents specific to the Cisco IAD2430 are available on Cisco.com at the following location:

http://www.cisco.com/univercd/cc/td/doc/product/access/iad/iad2430/index.htm

Cisco Feature Navigator

Cisco Feature Navigator is a web-based tool that enables you to quickly determine which Cisco IOS software images support a particular set of features and which features are supported in a particular Cisco IOS image. Feature Navigator is available 24 hours a day, 7 days a week.

To use Cisco Feature Navigator, you must have a JavaScript-enabled web browser such as Netscape 3.0 or later, or Internet Explorer 4.0 or later. Internet Explorer 4.0 always has JavaScript enabled. To enable JavaScript for Netscape 3.x or Netscape 4.x, follow the instructions provided with the web browser. For JavaScript support and enabling instructions for other browsers, check with the browser vendor.

Feature Navigator is updated when major Cisco IOS software releases and technology releases occur. You can access Feature Navigator at the following URL:

http://www.cisco.com/go/cfn 

Cisco IOS Software Documentation Set

The Cisco IOS software documentation set consists of the Cisco IOS configuration guides, Cisco IOS command references, and several other supporting documents.

Documentation Modules

Each module in the Cisco IOS documentation set consists of one or more configuration guides and one or more corresponding command references. Chapters in a configuration guide describe protocols, configuration tasks, and Cisco IOS software functionality, and contain comprehensive configuration examples. Chapters in a command reference provide complete command syntax information. Use each configuration guide with its corresponding command reference. Cisco IOS Software Documentation is available in html or pdf form.

Select your release and click the command references, configuration guides, or any other Cisco IOS documentation you need.

Obtaining Documentation, Obtaining Support, and Security Guidelines

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.


hometocprevnextglossaryfeedbacksearchhelp

Posted: Fri Feb 22 00:45:09 PST 2008
All contents are Copyright © 1992--2008 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.