|
These release notes describe the Cisco IOS Release 12.0(3)T feature packs for Cisco 3600 series routers and contain the following topics:
This section explains how to use this document and describes feature pack components.
The tables in these release notes contain details about the Cisco feature packs. Use these tables to perform the following tasks before loading a software image onto a router:
1. Use Table 1, "Cisco 3600 Series Routers Default Memory and Upgrade Options," for the feature set memory requirements, and the factory-default memory and available memory upgrades for your Cisco 3600.
2. Use Table 2, "Feature Pack Product Numbers," to identify the software image you want to load.
3. Use Table 3, "Cisco Feature Pack Image Filenames and Memory Requirements," to identify your feature pack and the memory required for your feature set, based on the image you load.
4. Use the tables following the "Feature Set Tables" section to identify which features are supported in a feature set image.
A feature pack is a box that contains the following items:
The heart of a feature pack is the CD-ROM that contains software images and the RSL, which is a Windows 95 application that loads an image onto an access router or server. Each feature pack CD-ROM contains at least one Cisco IOS feature set. The CD-ROM booklet, Getting Started with the Router Software Loader, explains how to use the RSL to install the router image. If you cannot use the RSL to load images, you can follow the instructions in the "Alternatives to the RSL" section.
Before running the RSL, read the "Installing Software Images Using RSL" section. If you are loading software on a preconfigured router, you should save the router configuration file on your PC before beginning the image download process, as described in Getting Started with the Router Software Loader.
Table 1 describes the memory requirements and upgrade options for the Cisco 3600 series routers for Release 12.0(3)T.
The Cisco 3600 series includes the Cisco 3620 and Cisco 3640 routers. As modular solutions, the Cisco 3620 and 3640 routers enable corporations to increase dial-up density and take advantage of current and emerging Cisco wide-area network (WAN) technologies and networking capabilities. The Cisco 3600 series is fully supported by Cisco IOS software, which includes dial-up connectivity, LAN-to-LAN routing, data and access security, WAN optimization, and multimedia features. Multiservice applications are supported by integrated voice network modules.
The following LAN interfaces are supported on Cisco 3600 series routers:
The following WAN data rates are supported on Cisco 3600 series routers:
The following WAN interfaces are supported on Cisco 3600 series routers:
The feature packs described in these release notes contain Cisco IOS Release 12.0(3)T software images, some earlier images, and RSL Version 7.3. Before running RSL, read the "Installing Software Images Using RSL" section.
To determine the version of the Cisco IOS software that is currently running on your Cisco 3600 series router, log in to the router, and enter the show version user EXEC command. The following is sample screen output from the show version command. The version number is indicated on the second line as shown below:
The output includes more information, such as processor revision numbers, memory amounts, hardware IDs, and partition information.
For information on upgrading to a new software release, see the Cisco IOS Software Release 12.0T Upgrade (#819: 1/99) located on Cisco Connection Online (CCO).
Service and Support: Technical Documents: Product Bulletins: Cisco IOS Software Release 12.0T Upgrade (#819: 1/99)
The following table lists the Cisco product numbers of the feature packs supported in this release.
Product Number | Feature Pack Description |
---|---|
Cisco 3600 IP/FW Plus IPSEC 56 Feature Pack2 |
|
Cisco 3600 IP Plus IPSEC 56 Feature Pack2 |
|
Cisco 3600 Enterprise Plus IPSEC 56 Feature Pack2 |
|
Cisco 3600 Enterprise/FW IPSEC 56 Feature Pack2 |
1FW is an abbreviation for firewall.
2This feature pack contains encryption images. |
Table 3 identifies each feature pack specified on the router software CD-ROM label, the feature sets in each feature pack, and UNIX and DOS filenames of the images, memory requirements, and RSL installer descriptions.
The Cisco IOS software is packaged into feature sets (also called images). Many different feature sets are available, and each feature set contains a specific subset of Cisco IOS features. The following conventions are used to identify feature sets:
Cisco IOS images with strong encryption (including, but not limited to, 56-bit DES) are subject to U.S. government export controls and have limited distribution. Images to be installed outside the U.S. require an export license. Customer orders might be denied or subject to delay depending on U.S. government regulations. Contact your Cisco sales representative or distributor for more information, or send e-mail to export@cisco.com.
The following list shows which feature sets are supported on the Cisco 3600 series routers. These feature sets only apply to Cisco IOS Release 12.0(3)T:
Table 4 and Table 5, which follow, list the features and feature sets supported by the Cisco 3600 series routers in Cisco IOS Release 12.0(3)T and both tables use the following conventions to identify features:
Note These feature set tables contain only a selected list of features, rather than a cumulative or complete list of all the features in each image. Information may be missing or outdated. Please consult the online version of the this publication for updates.
Features | In | Software Images by Feature Sets | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
IP | IP Plus | IP Plus 40 | IP Plus IPSec 56 | IP/ FW1 |
IP/ FW Plus IPSec 56 |
IP/IPX/ AT/ DEC |
IP/IPX/ AT/ DEC Plus |
IP/IPX/AT/ DEC/ FW1 Plus |
||
Connectivity | ||||||||||
IBM Support | ||||||||||
IP Routing | ||||||||||
Management | ||||||||||
Quality of Service | ||||||||||
Security | ||||||||||
Switching | ||||||||||
WAN Services | ||||||||||
1FW is an abbreviation for firewall.
2Cisco 3640 routers only |
1Cisco 3640 routers only |
This section describes the following topics:
The Router Software Loader (RSL) Version 7.3 supports the following Cisco 3600 series routers:
This section describes solutions to problems you might encounter when installing software images using the RSL, in addition to the solutions you can find in RSL online help.
This installation tip provides a possible recovery solution if you are unable to connect to your access server or router. Unless you are experiencing a connection error, you can skip this section.
In some cases, you might receive the following error message while connecting to the target access server:
If you encounter this message, try increasing the Short Timeout value to more than than 25 seconds in the Options dialog box:
Note Increasing the Short Timeout value might increase the time it takes for the RSL to connect to the target access server.
In some cases, the RSL is unable to restore the startup configuration. If this happens, follow these steps:
Step 2 Restart the RSL and connect by using the Preconfigured router option.
Step 3 When asked if you want to overwrite the existing startup configuration file, choose no.
Step 4 When asked if you want to continue, choose yes.
Step 5 When the router is connected, select Download Router Configuration in the Router Software Loader dialog box.
Step 6 Select the appropriate file and click the radio button beside Copy configuration to the router nonvolatile memory.
The router should now contain the startup configuration it had before the initial RSL connection. You can now exit the RSL.
Note In the previous situation, the router configuration register (config-register 0xnnnn) is not restored.
Note If you press Ctrl-Alt-Delete to terminate the RSL, the router configuration and configuration register are not restored. However, in this case, the configuration file is not deleted from the PC, so you can restore it using the previous steps, beginning with Step 2.
The following information about RSL operations can help you with the installation process:
The RSL has an upgrade utility to permanently modify a CiscoPro router so that it accepts Cisco IOS Release 12.0 T software images. The utility changes the router SysObjectID Simple Network Management Protocol (SNMP) MIB value (used for network management) to that of a Cisco router. The software banner also changes and no longer identifies the router as a CiscoPro product.
Note After this upgrade, CiscoVision cannot recognize your router. If you choose the permanent upgrade, CiscoWorks for Windows is a recommended replacement for network management purposes. To upgrade your CiscoVision software to CiscoWorks Windows 2.1, order one of the following: CPW-CVCW-U to Upgrade CiscoVision to CiscoWorks Windows (managing up to 50 nodes) or CPW-CVCW-ENT-U to Upgrade CiscoVision to CiscoWorks Windows (managing up to 500 nodes). For general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.
If you select a Cisco IOS Release 12.0 T image from the image list and are connected to a CiscoPro CPA3600, a message box tells you that the router requires a permanent upgrade to load this image. You can either select yes to have the RSL upgrade the router and continue loading the selected image, or select no to cancel the load operation.
If you select yes, the RSL utility downloads, performs the upgrade, reboots the router, and issues a message to confirm the upgrade. Confirm this message. The RSL then downloads the selected image.
The upgrade utility must be located in the Images directory. If it is not, the upgrade utility informs you that the image is not present.
The Cisco 3600 series upgrade utility filename is cpa3600-upgrade-l.112-3.P.. The upgrade utility is a special file, not a Cisco IOS run-time image. RSL only installs valid software releases on Cisco 3600 series routers.
The RSL is designed to work with a PC running Microsoft Windows 95 and is the recommended method for downloading software to the router. The booklet included with the CD-ROM explains how to perform this simple install process; however, two alternatives are available for installing router software:
This section explains how to use the copy xmodem flash command to install the router software from the CD-ROM onto the router.
Note The transfer takes place only on the port at which you enter the command. If you download via the console, all console output is discarded for the duration of the transfer. You can only download files to the router; you cannot copy files from the router. Cisco recommends using the auxiliary port for this type of software download. The auxiliary port has hardware flow control and full modem control. In addition, the transfer does not occupy the system console so it is free for other uses.
The following example shows how to use the copy xmodem flash command on a Cisco 3600 series router.
Use this TFTP server application method as an alternative to using the RSL to install the router software from the CD-ROM. You can perform this procedure using a PC (running Microsoft Windows 95 or Microsoft Windows 3.1), a Macintosh, or a UNIX system. You can use either the copy tftp flash or copy rcp flash command to download the router software to the router.
First, obtain a TFTP application or a remote copy protocol (rcp) application to set up your computer as a TFTP server or a rcp server. Only use the RSL or the TFTP server included on the feature pack CD-ROM to install the router software if you are using a PC running Windows 95. For other operating systems, a number of TFTP or rcp applications are available from independent software vendors or available as shareware from public sources on the World Wide Web.
Note To use an rcp application, follow the same procedure below, substituting "rcp" for "TFTP"and using the copy rcp flash command instead of the copy tftp flash command.
Step 2 Launch the TFTP server application on the PC, usually by double-clicking the application icon or its .exe filename.
Step 3 Set up the PC as a TFTP server by using the TFTP server application setup or configuration facility.
Most TFTP server applications include a setup facility that allows you to specify the PC as a server. For example, from the TFTP menu of one application, you can select Settings to display a panel, and configure the local PC as a server by selecting the Server checkbox.
The TFTP server also allows the selection of a "root" directory. You must select the directory in which the Cisco IOS files reside (for example, d:\cpswinst\images).
Caution Make sure you set up your local PC as a TFTP server. If you overlook this step, you cannot perform the copy procedure. This reminder applies to both TFTP and rcp. |
Step 4 Establish a console session from your local PC (which is now configured as a TFTP server) to the Cisco router by using one of these methods:
This is the recommended method.When you reload the router with the new image in Step 25, you remain connected to the router. (If you use Telnet, you lose connection to the router.)
Step 5 Connect your PC Ethernet port to the corresponding router LAN port. Use the 10BaseT crossover cable to connect to an Ethernet port. Use straight-through cables if you are connecting via a 10BaseT hub or a 100BaseT hub.
Note We recommend that you back up the router configuration before upgrading the router software.
Step 6 Enter the following commands to set the configuration register to 0x2101 and reload to the bootstrap image:
Step 7 When asked whether the system configuration has been modified, enter yes:
Step 8 If the password prompt appears, enter the password.
Step 9 At the router prompt, enter enable and then the password:
Step 10 If you are not upgrading a CiscoPro CPA1600 router, skip to Step 19.
Step 11 At the router prompt, enter the following command to copy the router upgrade utility from the PC CD-ROM drive to the router:
Note If you are using rcp, enter copy rcp flash instead.
Step 12 When prompted, enter the IP address of your PC, as in the following example:
Address or name of remote host [255.255.255.255]? 131.108.1.1
This is the IP address of your local PC, not the router. (Note that you can obtain your PC IP address from the DOS prompt in the windows directory by entering winipcfg, as follows: C:\WINDOWS> winipcfg.)
Step 13 When prompted, enter the filename of the image to be copied to the router as in the following example:
Source file name? cpa1600-upgrade-l.112-3.P
Note The upgrade image file on the Feature Pack CD-ROM has a long filename (cpa1600-upgrade-l.112-3.P); note that DOS displays it in 8.3 format as cpa1600~1.P. The upgrade utility is a special file, not a Cisco IOS run-time image.
Step 14 In response to the following prompt, enter the destination filename, and press Enter.
Destination file name [cpa1600-upgrade-l.112-3.P]? cpa1600-upgrade-l.112-3.P
(This is the name of the image file on the router, not the full pathname of the image on the PC CD-ROM.)
During the transfer process, messages indicate that the software has accessed the file you have specified and is loading it.
If the file is not found, check the following:
If the file is still not found, create a temporary directory entitled "C:\temp," and copy the CiscoPro upgrade file into the directory. Select the C:\temp directory as the root directory.
Step 15 When asked whether you want to erase the existing image in the router Flash memory before copying the new one, enter yes:
Erase flash device before writing? [confirm] yes
The entire copying process takes several minutes and differs from network to network. The exclamation point (!) indicates that the copy process is taking place. Each exclamation point indicates that ten packets have been transferred successfully. If you see three or more periods (...), the transfer might fail. If the transfer fails, use the ping command to check IP connectivity between the router and TFTP server.
Step 16 Enter the reload command to reload the router:
Do not save the configuration.
After reload is complete, your CiscoPro router has been upgraded to a Cisco Enterprise router. Because the original Cisco IOS image that resided in Flash memory was erased during the upgrade process, the router is now running in bootstrap mode.
Step 17 If the password prompt appears, enter the password.
Step 18 At the router prompt, enter enable and then the password:
Step 19 At the router prompt, enter the following command to copy the new software image from the PC CD-ROM drive to the router:
Router(boot)(config)# copy tftp flash
In the next series of steps, you download the Cisco IOS Release 12.0 T images that you want installed on your router.
Step 20 When prompted, enter the IP address of your PC, as in the following example:
Address or name of remote host [255.255.255.255]? 131.108.1.1
This is the IP address of your local PC, not that of the router.
Step 21 When prompted, enter the filename of the Cisco IOS Release 12.0 T image to be copied to the router, as in the following example:
This example specifies the DOS image name of the IP feature set for Cisco 3600 series routers (as shown in Table 3 in the section, "Feature Pack Overview Table").
Step 22 In response to the prompt, enter the destination UNIX image filename, and press Enter.
This is the name of the image file on the router, not the full pathname of the image on the CD-ROM attached to the PC. Refer to Table 3 in the section, "Feature Pack Overview Table" for the UNIX image filename.
During the transfer process, the software displays messages indicating that it has accessed the file you have specified and is loading it.
Step 23 Enter yes in response to the prompt asking if you want to erase the existing image copy resident in the router Flash memory before copying the new one.
Erase flash device before writing? [confirm] yes
The entire copying process takes several minutes and differs from network to network.
The exclamation point (!) indicates that the copy process is taking place. Each exclamation point (!) indicates that ten packets have been transferred successfully. A checksum verification of the image occurs after the image is written to Flash memory.
Step 24 Enter the following commands to reset the configuration register to 0x2102.
Step 25 Enter the reload command to reload the router:
After reload is complete, the router should be running the required Cisco IOS image. Use the show version command to verify.
This section describes the documentation related to the Cisco 3600, typically including hardware installation guides, software installation guides, Cisco IOS configuration and command references, system error messages, and feature modules that are updates to the Cisco IOS documentation set. Documentation is available as printed manuals or electronic documents, except for the feature modules, which are available online only.
The most up-to-date documentation can be found on the Web via Cisco Connection Online (CCO) and on the latest Documentation CD-ROM. These electronic documents might contain updates and modifications made after the paper documents were printed. See the "Cisco Connection Online" section and the "Documentation CD-ROM" section for more information.
This section contains the following subsections:
The following documents are specific to Release 12.0 T. They are located on CCO and the Documentation CD-ROM:
To access the cross-platform Release Notes for Cisco IOS Release 12.0 T on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Cross-Platform Release Notes for Cisco IOS Release 12.0 T
To access the cross-platform Release Notes for Cisco IOS Release 12.0 T on the Documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Cross-Platform Release Notes for Cisco IOS Release 12.0 T
To access these documents, refer to the Software Center at this path on CCO:
Service & Support: Technical Documents
For caveat details, see the Caveats for Cisco IOS Release 12.0 T document, which contains caveats applicable to all platforms for all maintenance releases of Release 12.0 T.
To access the caveat document on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Caveats: Caveats for Cisco IOS Release 12.0 T
To access the caveat document on the Documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Caveats: Caveats for Cisco IOS Release 12.0 T
Note If you have an account with CCO, you can use Bug Navigator II to find caveats of any severity for any release. Bug Navigator II can be found at http://www.cisco.com/support/bugtools, or from CCO, select Service & Support: Online Technical Support: Software Bug Toolkit.
The following list contains the documents specific to the Cisco 3600. These documents are available on CCO and the Documentation CD-ROM.
To access these documents on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Access Servers and Access Routers: Modular Access Routers: Cisco 3600 Series Routers
To access these documents on the Documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Access Servers and Access Routers: Modular Access Routers: Cisco 3600 Series Routers
Feature modules describe new features introduced in 12.0 T releases and are updates to the Cisco IOS documentation set. As updates, the features modules are available online only. The feature module information will be added to the Cisco IOS documentation set before the next printing. Feature modules have a brief overview of the feature, benefits, configuration tasks, and a command reference.
To access the feature modules on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation
To access the feature modules on the documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation
The Cisco IOS software documentation set consists of the Cisco IOS configuration guides, Cisco IOS command references, and several other supporting documents. These documents are shipped with your order in electronic form on the Documentation CD-ROM, unless you specifically ordered the printed versions.
Each module in the Cisco IOS documentation set consists of two books: a configuration guide and a corresponding command reference. Chapters in a configuration guide describe protocols, configuration tasks, and Cisco IOS software functionality and contain comprehensive configuration examples. Chapters in a command reference provide complete command syntax information. Each configuration guide can be used in conjunction with its corresponding command reference.
To access these documents on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Cisco IOS Release 12.0 Configuration Guides and Command References
To access these documents on the Documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Cisco IOS Release 12.0: Cisco IOS Release 12.0 Configuration Guides and Command References
Table 6 details the contents of the Cisco IOS Release 12.0 software documentation set. The document set is available in electronic form, and also in printed form upon request.
Note The most current Cisco IOS documentation can be found on the latest Documentation CD-ROM and on the Web. These electronic documents might contain updates and modifications made after the paper documents were printed.
To access the Cisco IOS documentation set on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0
To access the Cisco IOS documentation set on the Documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Cisco IOS Release 12.0
Note The Cisco Management Information Base (MIB) User Quick Reference publication is no longer being published. For the latest list of MIBs supported by Cisco, see the Cisco Network Management Toolkit on Cisco Connection Online. On CCO, go to Software and Support: Software Center: Network Management Products: Cisco Network Management Toolkit: Cisco MIBs.
The following URL contains links and helpful tips on configuring your Cisco products: http://www.cisco.com/kobayashi/serv_tips.shtml.
This URL is subject to change without notice. You can also access this page by following this path from CCO:
Products & Technologies: Technical Tips
"Hot Tips" are popular tips and hints gathered from the Cisco Technical Assistance Center (TAC). Most of these documents are available from the TAC FAX-on-demand service. To access FAX-on-demand and receive documents at your FAX machine, from the USA, call 888-50-CISCO (888-502-4726). From other areas, call 415-596-4408.
The following sections are provided from the Technical Tips page:
Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.
You can access CCO in the following ways:
For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.
Note If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco's Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
Posted: Fri Jan 17 16:47:16 PST 2003
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.