cc/td/doc/product/software/ios120/relnote
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Release Notes for Cisco IOS Release 12.0(2a)T1 Feature Packs for Cisco 3600 Series Routers
Introduction
System Requirements
Modem Code Alert
Modem Code Information
Installation Notes
Related Documentation
Service and Support
Cisco Connection Online
Documentation CD-ROM

Release Notes for Cisco IOS Release 12.0(2a)T1 Feature Packs for Cisco 3600 Series Routers


February 12, 1999

These release notes describe the Cisco IOS Release 12.0(2a)T1 feature packs for Cisco 3600 series routers.

These release notes discuss the following topics:

Introduction

This section explains how to use this document, describes feature pack components, and has tables that define the aspects of a feature pack.

How to Use These Release Notes

The tables in these release notes contain details about the Cisco feature packs. Use these tables to perform the following tasks before loading a software image onto a router:

1. Use Table 1, "Feature Pack Product Numbers Quick-Reference List," to identify the software image you want to load.

2. Use Table 2, "Cisco Feature Pack Image Filenames and Memory Requirements," to identify your feature pack and the memory required for your feature set, based on the image you load.

3. Use Table 4, "Feature Lists by Feature Sets for the Cisco 3600 Series, Part 1 of 2," and Table 5, "Feature Lists by Feature Sets for the Cisco 3600 Series, Part 2 of 2," to identify which features are supported in a feature set image.

4. Use Table 6, "Cisco 3600 Series Default Memory and Upgrade Options," to check the memory required for your feature set, determine the factory-default memory on the router, and view the available memory upgrades.

What Is a Feature Pack?

This section describes:

Feature Pack Components

A feature pack is a small box that contains the following items:

The heart of a feature pack is the CD-ROM that contains software images and the Router Software Loader (RSL), which is a Windows 95 application that loads an image onto an access server or router. Each feature pack CD-ROM contains at least one Cisco IOS feature set. The CD booklet, Getting Started with the Router Software Loader, explains how to use the RSL to install the router image. If you cannot use the RSL to load images, you can follow the instructions in the "Alternatives to the RSL" section.

Before running the RSL, read the "Installing Software Images Using the RSL" section. If you are loading software on a preconfigured router, you should save the router configuration file on your PC before beginning the image download process, as described in Getting Started with the Router Software Loader.

Product Numbers Quick-Reference List

Table 1 lists the Cisco product numbers of the feature packs supported in this release.

Table 1   Feature Pack Product Numbers Quick-Reference List

Product Number Feature Pack Description

CD36-C-12.0=

Cisco 3600 IP Feature Pack

CD36-CH-12.0=

Cisco 3600 IP/FW Feature Pack

CD36-CHL-12.0=

Cisco 3600 IP/FW Plus IPSEC 56 Feature Pack1

CD36-CL-12.0=

Cisco 3600 IP Plus IPSEC 56 Feature Pack1

CD36-CP-12.0=

Cisco 3600 IP Plus Feature Pack

CD36-CW-12.0=

Cisco 3600 IP Plus 40 Feature Pack1

CD36-B-12.0=

Cisco 3600 IP/IPX/AT/DEC Feature Pack

CD36-BHP-12.0=

Cisco 3600 IP/IPX/AT/DEC/FW Plus Feature Pack

CD36-BP-12.0=

Cisco 3600 IP/IPX/AT/DEC Plus Feature Pack

CD36-AL-12.0=

Cisco 3600 Enterprise Plus IPSEC 56 Feature Pack1

CD36-ANP-12.0=

Cisco 3600 Enterprise/APPN Plus Feature Pack

CD36-AP-12.0=

Cisco 3600 Enterprise Plus Feature Pack

CD36-AW-12.0=

Cisco 3600 Enterprise Plus 40 Plus Feature Pack1

CD36-AHL-12.0=

Cisco 3600 Enterprise/FW IPSEC 56 Feature Pack1

1This feature pack contains encryption images.

Feature Pack Overview Table

Table 2 identifies each feature pack as specified on the router software CD-ROM label, describes the feature sets in each feature pack, and lists the UNIX and DOS filenames of the images, memory requirements, and the RSL installer description.

Table 2   Cisco Feature Pack Image Filenames and Memory Requirements

Model Number CD-ROM Title UNIX Image Name DOS Image Name Flash MemoryReq'd Main MemoryReq'd Software Description
CD36-C-12.0=

Cisco 3600
IP Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-i-mz.113-6.T

aaa0001

4 MB

16 MB

Cisco 3640 IP Feature Set, Release 11.3(6)T

c3640-imz.120-2a.T1

aaa0002

4 MB

16 MB

Cisco 3640 IP Feature Set, Release 12.0(2a)T1

c3620-i-mz-113-6.T

aaa0003

4 MB

16 MB

Cisco 3620 IP Feature Set, Release 11.3(6)T

c3620-i-mz.120-2a.T1

aaa0004

4 MB

24 MB

Cisco 3620 IP Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0005

MICA Modem Portware Version 2.5.1.0

CD36-CH-12.0=

Cisco 3600
IP/FW Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-io-mz.120-2a.T1

aaa0006

8 MB

24 MB

Cisco 3640 IP/FW Feature Set, Release 12.0(2a)T1

c3640-io-mz.120-2a.T1

aaa0007

8 MB

24 MB

Cisco 3620 IP/FW Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0008

MICA Modem Portware Version 2.5.1.0

CD36-CHL-12.0=

Cisco 3600
IP/FW Plus IPSEC 56 Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-ios56i-mz.120-2a.T1

aaa0009

8 MB

32 MB

Cisco 3640 IP/FW Plus IPSEC 56 Feature Set, Release 12.0(2a)T1

c3640-ios56i-mz.120-2a.T1

aaa0010

8 MB

32 MB

Cisco 3620 IP/FW Plus IPSEC 56 Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0011

MICA Modem Portware Version 2.5.1.0

CD36-CL-12.0=

Cisco 3600
IP Plus IPSEC 56
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-is56i-mz.113-6.T

aaa0012

8 MB

32 MB

Cisco 3640 IP Plus IPSEC 56 Feature Set, Release 11.3(6)T

c3620-is56i-mz-120-2a.T1

aaa0013

8 MB

32 MB

Cisco 3640 IP Plus IPSEC 56 Feature Set, Release 12.0(2a)T1

c3620-is56i-mz-113-6.T

aaa0014

8 MB

32 MB

Cisco 3620 IP Plus IPSEC 56 Feature Set, Release 11.3(6)T

c3620-is56i-mz-120-2a.T1

aaa0015

8 MB

32 MB

Cisco 3620 IP Plus IPSEC 56 Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0016

MICA Modem Portware Version 2.5.1.0

CD36-CP-12.0=

Cisco 3600
IP Plus Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-is-mz.113-6.T

aaa0017

8 MB

16 MB

Cisco 3640 IP Plus
Feature Set, Release 11.3(6)T

c3640-is-mz.120-2a.T1

aaa0018

8 MB

32 MB

Cisco 3640 IP Plus
Feature Set, Release 12.0(2a)T1

c3640-is-mz.113-6.T

aaa0019

8 MB

16 MB

Cisco 3620 IP Plus
Feature Set, Release 11.3(6)T

c3640-is-mz.120-2a.T1

aaa0020

8 MB

32 MB

Cisco 3620 IP Plus
Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0021

MICA Modem Portware Version 2.5.1.0

CD36-CW-12.0=

Cisco 3600
IP Plus 40
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-is40-mz.113-6.T

aaa0022

8 MB

24 MB

Cisco 3640 IP Plus 40
Feature Set, Release 11.3(6)T

c3640-is40-mz.120-2a.T1

aaa0023

8 MB

32 MB

Cisco 3640 IP Plus 40
Feature Set, Release 12.0(2a)T1

c3640-is40-mz.113-6.T

aaa0024

8 MB

24 MB

Cisco 3620 IP Plus 40
Feature Set, Release 11.3(6)T

c3640-is40-mz.120-2a.T1

aaa0025

8 MB

32 MB

Cisco 3620 IP Plus 40
Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0026

MICA Modem Portware Version 2.5.1.0

CD36-B-12.0=

Cisco 3600
IP/IPX/AT/DEC
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-d-mz.113-6.T

aaa0027

4 MB

24 MB

Cisco 3640 IP/IPX/AppleTalk/DECnet Feature Set, Release 11.3(6)T

c3620-d-mz-120-2a.T1

aaa0028

8 MB

24 MB

Cisco 3640 IP/IPX/AppleTalk/DECnet Feature Set, Release 12.0(2a)T1

c3640-d-mz.113-6.T

aaa0029

4 MB

24 MB

Cisco 3620 IP/IPX/AppleTalk/DECnet Feature Set, Release 11.3(6)T

c3620-d-mz-120-2a.T1

aaa0030

8 MB

24 MB

Cisco 3620 IP/IPX/AppleTalk/DECnet Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0031

MICA Modem Portware Version 2.5.1.0

CD36-BHP-12.0=

Cisco 3600
IP/IPX/AT/DEC/FW Plus Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-dos-mz.120-2a.T1

aaa0032

8 MB

32 MB

Cisco 3640 IP/IPX/AppleTalk/DECnet/FW Plus Feature Set, Release 12.0(2a)T1

c3620-dos-mz.120-2a.T1

aaa0033

8 MB

32 MB

Cisco 3620 IP/IPX/AppleTalk/DECnet/FW Plus Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0031

MICA Modem Portware Version 2.5.1.0

CD36-BP-12.0=

Cisco 3600
IP/IPX/AT/DEC Plus
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-ds-mz.113-6.T

aaa0035

8 MB

32 MB

Cisco 3640 IP/IPX/AT/DECnet Plus Feature Set,
Release 11.3(6)T

c3640-ds-mz.120-2a.T1

aaa0036

8 MB

32 MB

Cisco 3640 IP/IPX/AT/DECnet Plus Feature Set,
Release 12.0(2a)T1

c3620-ds-mz-113-6.T

aaa0037

8 MB

32 MB

Cisco 3620 IP/IPX/AT/DECnet Plus Feature Set,
Release 11.3(6)T

c3620-ds-mz.120-2a.T1

aaa0038

8 MB

32 MB

Cisco 3620 IP/IPX/AT/DECnet Plus Feature Set,
Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0039

MICA Modem Portware Version 2.5.1.0

CD36-AL-12.0=

Cisco 3600
Enterprise Plus IPSEC 56
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-js56i-mz.113-6.T

aaa0040

8 MB

32 MB

Cisco 3640 Enterprise Plus IPSEC 56 Feature Set,
Release 11.3(6)T

c3640-js56i-mz.120-2a-T1

aaa0041

8 MB

48 MB

Cisco 3640 Enterprise Plus IPSEC 56 Feature Set,
Release 12.0(2a)T1

c3620-js56i-mz.113-6.T

aaa0042

8 MB

32 MB

Cisco 3620 Enterprise Plus IPSEC 56 Feature Set,
Release 11.3(6)T

c3620-js56i-mz.120-2a-T1

aaa0043

8 MB

48 MB

Cisco 3620 Enterprise Plus IPSEC 56 Feature Set,
Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0044

MICA Modem Portware Version 2.5.1.0

CD36-ANP-12.0=

Cisco 3600
Enterprise/APPN Plus
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-ajs-mz.120-2a.T1

aaa0045

8 MB

48 MB

Cisco 3640 Enterprise/APPN Plus Feature Set, Release 12.0(2a)T1

c3620-ajs-mz.120-2a.T1

aaa0046

8 MB

48 MB

Cisco 3620 Enterprise/APPN Plus Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0047

MICA Modem Portware Version 2.5.1.0

CD36-AP-12.0=

Cisco 3600
Enterprise Plus
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-js-mz.113-6.T

aaa0048

8 MB

32 MB

Cisco 3640 Enterprise Plus Feature Set, Release 11.3(6)T

c3640-js-mz.120-2aT1

aaa0049

8 MB

32 MB

Cisco 3640 Enterprise Plus Feature Set 12.0(2a)T1

c3620-js-mz.113-6.T

aaa0050

8 MB

32 MB

Cisco 3620 Enterprise Plus Feature Set, Release 11.3(6)T

c3620-js-mz.120-2aT1

aaa0051

8 MB

48 MB

Cisco 3620 Enterprise Plus Feature Set 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0052

MICA Modem Portware Version 2.5.1.0

CD36-AW-12.0=

Cisco 3600
Enterprise Plus 40 Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-js40-mz.113-6.T

aaa0053

8 MB

32 MB

Cisco 3640 Enterprise Plus 40 Feature Set, Release 11.3(6)T

c3640-js40-mz.120-2a.T1

aaa0054

8 MB

48 MB

Cisco 3640 Enterprise Plus 40 Feature Set, Release 12.0(2a)T1

c3620-js40-mz.113-6.T

aaa0055

8 MB

32 MB

Cisco 3620 Enterprise Plus 40 Feature Set 11.3(6)T

c3620-js40-mz.120-2a.T1

aaa0056

8 MB

48 MB

Cisco 3620 Enterprise Plus 40 Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0057

MICA Modem Portware Version 2.5.1.0

CD36-AHL-12.0=

Cisco 3600
Enterprise/FW IPSEC 56
Feature Pack
Release 12.0(2a)T1
RSL Version 7.3

c3640-jos56i-mz.120-2a.T1

aaa0058

8 MB

32 MB

Cisco 3640 Enterprise Plus 56 Feature Set, Release 12.0(2a)T1

c3620-jos56-mz.120-2a.T1

aaa0059

8 MB

32 MB

Cisco 3620 Enterprise Plus 56 Feature Set, Release 12.0(2a)T1

MICA Modem Portware

mica-modem-portware.
2.5.1.0.bin

aaa0060

MICA Modem Portware Version 2.5.1.0

Feature Set Table

The Cisco IOS software is packaged into feature sets (also called images). Many different feature sets are available, and each feature set contains a specific subset of Cisco IOS features. The following conventions are used to identify feature sets:

Cisco IOS images with strong encryption (including, but not limited to, 56-bit DES) are subject to U.S. government export controls and have a limited distribution. Images to be installed outside the U.S. require an export license. Customer orders might be denied or subject to delay due to U.S. government regulations. Contact your sales representative or distributor for more information, or send e-mail to export@cisco.com.

The following list shows which feature sets are supported on the Cisco 3600 series routers. These feature sets only apply to Cisco IOS Release 12.0 T:

Table 3   Feature Set Matrix for Cisco 3600 Series Routers

Standard
Feature Sets
Cisco 3600 Series

IP

Basic, Plus, Encrypt

Desktop (IP/IPX/AppleTalk/DEC)

Basic, Plus

Enterprise

Plus, Encrypt

Enterprise/APPN

Plus

Table 4 and Table 5 list the features and feature sets supported by Cisco IOS Release 12.0(2a)T1 for the Cisco 3600 series. The feature set table uses the following terms:

Feature Set
Table Term
Description

Yes

This feature is offered in the feature set.

No

This feature is not offered in the feature set.


Note      These feature set tables contain only a selected list of features. This table is not a cumulative or complete list of all the features in each image.


Table 4   Feature Lists by Feature Sets for the Cisco 3600 Series, Part 1 of 2

Feature Set
Features IP IP Plus IP Plus 40 IP Plus IPSec 56 IP/FW IP/FW Plus IPSec 56 IP/IPX/
AT/DEC
IP/IPX/
AT/
DEC Plus
IP/IPX/AT/
DEC/
FW Plus
Connectivity

Layer 2 Tunnel Protocol (L2TP)

No

Yes

Yes

Yes

No

Yes

No

Yes

Yes

RIP Enhancements

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

IP Routing

Easy IP Phase 2-DHCP Server

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

OSPF Packet Pacing

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Management

ISDN MIB RFC 2127

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Smart-init (Mars FE2P)

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Quality of Service

CLI String Search

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Security

Cisco IOS Firewall Feature Set Platform Support

No

No

No

No

Yes

Yes

No

No

Yes

Switching

Cisco IOS STP Enhancements

No

Yes

Yes

Yes

No

Yes

No

Yes

Yes

WAN Services

Cisco IOS IEEE 802.1Q

No

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Mobile IP

No

Yes

Yes

Yes

No

Yes

No

Yes

Yes

PPP Over Frame Relay

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

R2 Signaling

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Time-Based Access Lists

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Table 5   Feature Lists by Feature Sets for the Cisco 3600 Series, Part 2 of 2

Features Enterprise Plus Enterprise Plus
40
Enterprise Plus IPSec 56 Enterprise/
FW IPSec
56
Enterprise/
APPN Plus
Connectivity

Layer 2 Tunnel Protocol (L2TP)

Yes

Yes

Yes

Yes

Yes

RIP Enhancements

Yes

Yes

Yes

Yes

Yes

IP Routing

Easy IP Phase 2-DHCP Server

Yes

Yes

Yes

Yes

Yes

OSPF Packet Pacing

Yes

Yes

Yes

Yes

Yes

Management

ISDN MIB RFC 2127

Yes

Yes

Yes

Yes

Yes

Smart-init (Mars FE2P)

Yes

Yes

Yes

Yes

Yes

Quality of Service

CLI String Search

Yes

Yes

Yes

Yes

Yes

Security

Cisco IOS Firewall Feature Set Platform Support

No

No

No

Yes

No

Switching

Cisco IOS STP Enhancements

Yes

Yes

Yes

Yes

Yes

WAN Services

Cisco IOS IEEE 802.1Q

Yes

Yes

Yes

Yes

Yes

Mobile IP

Yes

Yes

Yes

Yes

Yes

PPP Over Frame Relay

Yes

Yes

Yes

Yes

Yes

R2 Signaling

Yes

Yes

Yes

Yes

Yes

Time-Based Access Lists

Yes

Yes

Yes

Yes

Yes

System Requirements

This section describes the following:

Memory Requirements

Table 6 lists the default memory and the available memory upgrades.

Table 6   Cisco 3600 Series Default Memory and Upgrade Options

Memory Type Cisco 3600 Series Defaults Upgrade Options

Flash SIMM

4 MB

4-MB upgrade: MEM3600-4FS=
8-MB upgrade: MEM3600-8FS=
16-MB upgrade: MEM3600-16FS=
16-MB upgrade: MEM3600-2X8FS=
32-MB upgrade: MEM3600-2X16FS=

Flash PCMCIA

0 MB

4-MB upgrade: MEM3600-4FC=
8-MB upgrade: MEM3600-8FC=
16-MB upgrade: MEM3600-16FC=

DRAM SIMM

32 MB

For the 3620:
4-MB upgrade: MEM3620-4D=
8-MB upgrade: MEM3620-8D=
16-MB upgrade: MEM3620-16D=
For the 3640:
8-MB upgrade: MEM3640-2X4D= (2x4 MB DRAM SIMMs)
16-MB upgrade: MEM3640-2X8D= (2x16 MB DRAM SIMMs)
32-MB upgrade: MEM3640-2X16D= (2x16 MB DRAM SIMMs)
64-MB upgrade: MEM3640-2X32D= (2x32MB DRAM SIMMs)
128-MB upgrade: MEM3640-4X32D= (4x32MB DRAM SIMMs)

Hardware Supported

The Cisco 3600 series includes the Cisco 3620 and Cisco 3640 routers. As modular solutions, the Cisco 3620 and 3640 enable corporations to increase dialup density and take advantage of current and emerging Cisco WAN technologies and networking capabilities. The Cisco 3600 series is fully supported by Cisco IOS software, which includes dialup connectivity, LAN-to-LAN routing, data and access security, WAN optimization, and multimedia features.

The following LAN interfaces are supported on Cisco 3600 series routers:

The following WAN data rates are supported on Cisco 3600 series routers:

The following WAN interfaces are supported on Cisco 3600 series routers:

Software Compatibility

The feature packs described in these release notes contain Cisco IOS Release 12.0(2a)T1 software images, some earlier images, and the Router Software Loader (RSL) Version 7.3. Before running the RSL, read the "Installing Software Images Using the RSL" section.

Determining Your Software Release

To view the version of Cisco IOS software that is running on your Cisco 3600 series router, log in to the router, and enter the show version user EXEC command:

router> show version

The output begins similar to the following. The Cisco IOS version appears in the second line.

Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3600-JS-M), Version 12.0(2a)T1, RELEASE SOFTWARE

The output includes more information including processor revision numbers, memory amounts, hardware IDs, and partition information.

Modem Code Alert

By default, the MICA modems installed on the Cisco 3600 series routers use the modem portware that is bundled with the Cisco IOS software image. Unless you are familiar with the Cisco MICA portware, we recommend that you use the default firmware and do not attempt to download another version.

If you do choose to override the firmware and portware selected by Cisco IOS software, the Flash memory of your router might contain modem code files that should be saved and restored before downloading the new image. Before the image download begins, the Router Software Loader (RSL) will display the Flash Copy Options dialog box, which will allow you to select which files to back up and restore. By default, RSL will back up all files in the selected Flash memory partition and restore the files you select.

If you want to verify that you are running the latest modem code, use the show modem version command to display the current version. Then compare that version to the modem code files available on the feature pack CD-ROM and on Cisco Connection Online (CCO).

Modem Code Information

If you are running Microsoft Windows 95 on a PC, we recommend using the RSL to download modem code. For detailed steps, refer to the RSL online help topic, "Downloading Modem Files." If you are running Windows NT, UNIX, or Macintosh, use TFTP or remote copy protocol (rcp) to download modem code. TFTP server instructions are in the online document titled Another Way to Download Modem Code.

Both RSL and TFTP instructions are available from the Software Center at the following URL:

http://www.cisco.com/public/sw-center/sw-access.shtml

Click on the link Router Software Loader (RSL). Follow the steps to download the new modem code.

Installation Notes

This section provides solutions to problems you might encounter when using the RSL to load Cisco IOS software on a router. It also describes special cases that might require you to load Cisco IOS software on a CiscoPro router or to use an alternative to the RSL.

Installing Software Images Using the RSL

The Router Software Loader (RSL) Version 7.3 supports the following Cisco 3600 series routers:

This section describes some solutions to problems you might encounter when using the RSL. These solutions are additions to the RSL online help.

Recovering from a Connection Error

This installation tip provides a possible recovery solution if you are unable to connect to your router. You can skip this section unless you are experiencing a connection error.

In some cases, you might receive the following error message while connecting to the target router:

"Failed to configure the router to enable the Cisco IOS software image and configuration file upload and download operations. You may want to check the router to make sure that the selected interface exists."

If you encounter this message, try increasing the Short Timeout value in the Options dialog box from 25 seconds, especially if one of the following situations applies:


Note      Increasing the Short Timeout value might increase the time it takes for the RSL to connect to the target router.


Restoring the Startup Configuration

In some cases, the RSL is unable to restore the startup configuration. If this happens, take the following steps:


Step 1   Ensure that all cables are properly attached to both the router and the PC.

Step 2   Restart the RSL, and connect by using the Preconfigured router option.

Step 3   When asked if you want to overwrite the existing startup configuration file, choose no.

Step 4   When asked if you want to continue, choose yes.

Step 5   When the router is connected, select Download Router Configuration in the Router Software Loader dialog box.

Step 6   Select the appropriate file, and click the radio button beside Copy configuration to the router nonvolatile memory.

The router should now contain the startup configuration it had before the initial RSL connection. You can now exit the RSL.


Note      In the previous situation, the router configuration register (config-register 0xnnnn) is not restored.



Note      If you press Ctrl-Alt-Delete to terminate the RSL, the router configuration and configuration register are not restored. However, in this case the configuration file is not deleted from the PC, so you can restore it using the previous steps, beginning with Step 2.


Helpful Hints

The following information about RSL operations can help you with the installation process:

Loading Cisco IOS Release 12.0 Software on CiscoPro Routers

The RSL has an upgrade utility to permanently modify a CiscoPro router so that it accepts Cisco IOS Release 12.0 software images. The utility changes the router SysObjectID Simple Network Management Protocol (SNMP) MIB value (used for network management) to that of a Cisco router. The software banner also changes and no longer identifies the router as a CiscoPro product.


Note      After this upgrade, CiscoVision cannot recognize your router. If you choose the permanent upgrade, CiscoWorks for Windows is a recommended replacement for network management purposes. To upgrade your CiscoVision software to CiscoWorks Windows 2.1, order one of the following: CPW-CVCW-U to Upgrade CiscoVision to CiscoWorks Windows (managing up to 50 nodes) or CPW-CVCW-ENT-U to Upgrade CiscoVision to CiscoWorks Windows (managing up to 500 nodes). For general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.


If you select a Cisco IOS Release 12.0 image from the image list and are connected to a CiscoPro CPA3600 series router, a message box tells you that the router requires a permanent upgrade to load this image. You can either select yes to have the RSL upgrade the router and continue loading the selected image or select no to cancel the load operation.

After you select yes, the RSL downloads, performs the upgrade, reboots the router, and issues a message to confirm the upgrade. Confirm this message. The RSL then downloads the selected image.

The upgrade utility must be located in the Images directory. If it is not, the upgrade utility informs you that the image is not present.

The Cisco 3600 series upgrade utility filename is cpa3600-upgrade-l.112-3.P. The upgrade utility is a special file, not a Cisco IOS run-time image. The RSL only installs valid software releases on Cisco 3600 series routers.

Alternatives to the RSL

The RSL is designed to work with a PC running Microsoft Windows 95 and is the recommended method for downloading software to the router. The booklet included with the CD-ROM explains how to perform this simple install process; however, two alternatives are available for installing router software:

Installing the Router Software Using the Console or Auxiliary Port

This section explains how to use the copy xmodem flash command to install the router software from the CD-ROM onto the router.


Note      The transfer takes place only on the port at which you enter the command. If you download via the console, all console output is discarded for the duration of the transfer. You can only download files to the router; you cannot copy files from the router. Cisco recommends using the auxiliary port for this type of software download. The auxiliary port has hardware flow control and full modem control. In addition, the transfer does not occupy the system console so it is free for other uses.


The following example shows how to use the copy xmodem flash command on a Cisco 3600 series router:

Router# copy xmodem flash
**** WARNING ****
x/ymodem is a slow transfer protocol limited to the current speed
settings of the auxiliary/console ports. The use of the auxiliary
port for this download is strongly recommended.
During the course of the download no exec input/output will be
available.
---- ******* ----
Proceed? [confirm] yes
Use crc block checksumming? [confirm] yes
Max Retry Count [10]:
Perform image validation checks? [confirm] yes
Xmodem download using crc checksumming with image validation
Continue? [confirm] yes
Partition Size Used Free Bank-Size State Copy Mode
1 4096K 3259K 836K 4096K Read/Write Direct
2 4096K 0K 4095K 4096K Read/Write Direct
[Type ?<no> for partition directory; ? for full directory; q to abort]
Which partition? [default = 1] 2
System flash directory, partition 2:
File Length Name/status
1 68 TESTFILE
[132 bytes used, 4194172 available, 4194304 total]
Destination file name? c3620-i-mz.0918
Erase flash device before writing? [confirm] yes
Flash contains files. Are you sure you want to erase? [confirm] yes
Copy '' from server
as 'c3620-i-mz.0918' into Flash WITH erase? [yes/no] yes
Erasing device... eeeeeeeeeeeeeeee ...erased
Ready to receive file...........C
Verifying checksum... OK (0x5DE8)
Flash device copy took 00:12:06 [hh:mm:ss]

Installing the Router Software Using a TFTP Server Application

This section explains how to use a TFTP server application as an alternative to using the RSL to install the router software from the CD-ROM. You can perform this procedure using a PC (running Microsoft Windows 95 or Microsoft Windows 3.1), a Macintosh, or a UNIX system. You can use either the copy tftp flash or copy rcp flash command to download the software to the router.

First, obtain a TFTP application or a remote copy protocol (rcp) application to set up your computer as a TFTP server or an rcp server. You can use the RSL or the TFTP server included on the feature pack CD-ROM to install the software only if you are using a PC running Windows 95. For other operating systems, a number of TFTP or rcp applications are available from independent software vendors or as shareware from public sources on the World Wide Web.


Note      To use an rcp application, follow this same procedure, but substitute rcp for TFTP in the instructions; for example, use the copy rcp flash command instead of the copy tftp flash command.



Step 1   Install any TFTP server application on the PC. (The PC application included on the feature pack CD-ROM is for Microsoft Windows 95 only.)

Step 2   Launch the TFTP server application on the PC, usually by double-clicking the application icon or its .exe filename.

Step 3   Set up the PC as a TFTP server by using the TFTP server application setup or configuration facility.

Most TFTP server applications include a setup facility that allows you to specify the PC as a server. For example, from the TFTP menu of one application, you can select Settings to display a panel that includes a checkbox beside the word Server. To configure the local PC as a server, click this checkbox.

The TFTP server also allows the selection of a "root" directory. You must select the directory in which the Cisco IOS files reside, for example, d:\cpswinst\images.


Make sure you set up your local PC as a TFTP server. If you overlook this step, you cannot perform the copy procedure. This reminder also applies if you are using rcp instead of TFTP.

Step 4   Establish a console session from your local PC (which is now configured as a TFTP server) to the router by using one of these methods:

This is the recommended method. When you reload the router with the new image in Step 12, you remain connected to the router. (If you use Telnet, you lose connection to the router.)

Step 5   Connect your PC Ethernet port to the router Ethernet port. Use an Ethernet crossover cable.


Note Use straight-through cables if you are connecting via a 10BaseT hub or a 100BaseT hub.


For systems without a LAN interface, make sure that the router and the PC have IP connectivity through the available interface (that is, the router and PC can ping each other with IP traffic).


Note We recommend that you back up the router configuration before upgrading the router software.


Step 6   Enter the following commands to enter enable mode and copy the new software image from the PC (set up as a TFTP server) to the router:

Router> enable
Password: <password>
Router#

Router# copy tftp flash

In the next series of steps, you download the Cisco IOS Release 12.0 images that you want installed on your router.

Step 7   When prompted, enter the IP address of your PC, as in the following example:

Address or name of remote host [255.255.255.255]? 172.16.1.1

This is the IP address of your local PC, not that of the router.

Step 8   When prompted, enter the filename of the Cisco IOS Release 12.0 image to be copied to the router, as in the following example:

Source file name? aaa0001.bin

This example specifies the DOS image name of the IP feature set for a Cisco 3600 series router, as listed in Table 2.

Step 9   In response to the prompt, enter the destination UNIX image filename, and press Enter.

This is the name of the image file on the router, not the full path name of the image on the CD-ROM attached to the PC. Refer to Table 2 in the "Cisco Feature Pack Image Filenames and Memory Requirements" section for the UNIX image filename.

Destination file name [aaa0001.bin]? c3640-i-mz.113-6.T

Step 10   Enter yes in response to the prompt asking if you want to erase the existing image copy resident in the router Flash memory before copying the new one:

Erase flash device before writing? [confirm] yes

The entire copying process takes several minutes and differs from network to network.

During the transfer process, the software displays messages indicating that it has accessed the file you have specified and is loading it.

The exclamation point (!) indicates that the copy process is taking place. Each exclamation point (!) indicates that ten packets have been transferred successfully. A checksum verification of the image occurs after the image is written to Flash memory.

Step 11   Enter the following commands to change the configuration register to 0x2102. This will force the router to reload to the image running from Flash memory.

Router# configure terminal
config-reg 0x2102
Router(config)#
Router(config)# end
Router#

Step 12   Enter the reload command to reload the router:

Router# reload

After reload is complete, the router should be running the desired Cisco IOS image. Use the show version command to verify.

Related Documentation

The following sections describe the documentation available for the Cisco 3600 series routers. Typically, these documents consist of hardware installation guides, software installation guides, Cisco IOS configuration and command references, system error messages, and feature modules, which are updates to Cisco IOS documentation. Documentation is available as printed manuals or electronic documents, except for feature modules, which are available online only.

The most up-to-date documentation can be found on the Web via Cisco Connection Online (CCO) and the Documentation CD-ROM. These electronic documents might contain updates and modifications made after the hard copy documents were printed.

These release notes should be used in conjunction with the documents listed in the following sections:

Release-Specific Documents

The following documents are specific to Release 12.0 T. They are located on CCO and the Documentation CD-ROM:

To access the cross-platform Release Notes for Cisco IOS Release 12.0 T on CCO, follow this path:

Service & Support: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes

To access the cross-platform Release Notes for Cisco IOS Release 12.0 on the Documentation CD-ROM, follow this path:

Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Cross-Platform Release Notes

To access these documents, refer to the Software Center at this path on CCO:

Service & Support: Technical Documents

As a supplement to the caveats listed in the "Caveats" section in these release notes, see the Caveats for Cisco IOS Release 12.0 T document, which contains caveats applicable to all platforms for all maintenance releases of Release 12.0 T.

To access the caveat document on CCO, follow this path:

Products and Ordering: Cisco Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Caveats: Caveats for Cisco IOS Release 12.0 T

To access the caveat document on the Documentation CD-ROM, follow this path:

Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS 12.0: Caveats: Caveats for Cisco IOS Release 12.0 T


Note      If you have an account with CCO, you can use Bug Navigator II to find caveats of any severity for any release. From the CCO home page, after logging in, click on this path: Service & Support: Online Technical Support: Software Bug Toolkit II. Bug Navigator II can also be found at http://www.cisco.com/support/bugtools.


Platform-Specific Documents

The documents listed below are available for the Cisco 3600 series routers. These documents are also available online at Cisco Connection Online (CCO) and on the Documentation CD-ROM.

To access Cisco 3600 series documentation on CCO, follow this path:

Products and Ordering: Cisco Documentation: Access Servers and Access Routers: Modular Access Routers: Cisco 3600 Series Routers

To access Cisco 3600 series documentation on the Documentation CD-ROM, follow this path:

Access Servers and Access Routers: Modular Access Routers: Cisco 3600 Series Routers

Feature Modules

Feature modules describe new features supported by Release 12.0 T and are an update to the Cisco IOS documentation set. They consist of a brief overview of the feature, benefits, configuration tasks, and a command reference. As updates, the features modules are available online only. The feature module information is included in the next printing of the Cisco IOS documentation set.

To access the feature modules on CCO, follow this path:

Service & Support: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation: New Features in Release 12.0 T

To access the feature modules on the Documentation CD-ROM, follow this path:

Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation: New Features in Release 12.0 T

Cisco IOS Software Document Set

The Cisco IOS software documentation set consists of the Cisco IOS configuration guides, Cisco IOS command references, and several other supporting documents. These documents are shipped with your order in electronic form on the Documentation CD-ROM, unless you specifically ordered the printed versions.

Documentation Modules

Each module in the Cisco IOS documentation set consists of two books: a configuration guide and a corresponding command reference. Chapters in a configuration guide describe protocols, configuration tasks, and Cisco IOS software functionality and contain comprehensive configuration examples. Chapters in a command reference provide complete command syntax information. Each configuration guide can be used in conjunction with its corresponding command reference.

To reach these documents on the CCO home page, click on this path:

Service & Support: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Cisco IOS 12.0 Configuration Guides and Command References: Configuration Guide Master Index or Command Reference Master Index

To reach these documents on the Documentation CD-ROM, click on this path:

Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Cisco IOS 12.0 Configuration Guides, Command References: Configuration Guide Master Index or Command Reference Master Index

Release 12.0 Documentation Set

Table 7 details the contents of the Cisco IOS Release 12.0 software documentation set. The document set is available in electronic form, and also in printed form upon request.


Note      The most current Cisco IOS documentation can be found on the latest Documentation CD-ROM and on the Web. These electronic documents might contain updates and modifications made after the paper documents were printed.


To access the Cisco IOS documentation set on CCO, follow this path:

Products and Ordering: Cisco Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0

To access the Cisco IOS documentation set on the Documentation CD-ROM, follow this path:

Cisco IOS Software Configuration: Cisco IOS Release 12.0

Table 7   Cisco IOS Software Documentation Set for Release 12.0

Books Chapter Topics
  • Configuration Fundamentals Configuration Guide
  • Configuration Fundamentals Command Reference

Configuration Fundamentals Overview
Cisco IOS User Interfaces
File Management
System Management

  • Bridging and IBM Networking Configuration Guide
  • Bridging and IBM Networking Command Reference

Transparent Bridging
Source-Route Bridging
Token Ring Inter-Switch Link
Remote Source-Route Bridging
DLSw+
STUN and BSTUN
LLC2 and SDLC
IBM Network Media Translation
DSPU and SNA Service Point
SNA Frame Relay Access Support
APPN
Cisco Database Connection
NCIA Client/Server Topologies
Cisco Mainframe Channel Connection
Airline Product Set

  • Dial Solutions Configuration Guide
  • Dial Solutions Command Reference

Dial-In Port Setup
Dial-In Terminal Services
Dial-on-Demand Routing (DDR)
Dial Backup
Dial-Out Modem Pooling
Large-Scale Dial Solutions
Cost-Control Solutions
ISDN
X.25 over ISDN
VPDN
Dial Business Solutions and Examples

  • Cisco IOS Interface Configuration Guide
  • Cisco IOS Interface Command Reference

Interface Configuration Overview

  • Network Protocols Configuration Guide, Part 1
  • Network Protocols Command Reference, Part 1

IP Addressing
IP Services
IP Routing Protocols

  • Network Protocols Configuration Guide, Part 2
  • Network Protocols Command Reference, Part 2

AppleTalk
Novell IPX

  • Network Protocols Configuration Guide, Part 3
  • Network Protocols Command Reference, Part 3

Apollo Domain
Banyan VINES
DECnet
ISO CLNS
XNS

  • Security Configuration Guide
  • Security Command Reference

AAA Security Services
Security Server Protocols
Traffic Filtering and Firewalls
IP Security and Encryption
Passwords and Privileges
Neighbor Router Authentication
IP Security Options

  • Cisco IOS Switching Services Configuration Guide
  • Cisco IOS Switching Services Command Reference

Switching Paths for IP Networks
Virtual LAN (VLAN) Switching and Routing

  • Wide-Area Networking Configuration Guide
  • Wide-Area Networking Command Reference

ATM
Frame Relay
SMDS
X.25 and LAPB

  • Voice, Video, and Home Applications Configuration Guide
  • Voice, Video, and Home Applications Command Reference

Voice over IP
Voice over Frame Relay
Voice over ATM
Voice over HDLC
Video Support
Universal Broadband Features

  • Quality of Service Solutions Configuration Guide1
  • Quality of Service Solutions Command Reference1

Classification
Scheduling
Packet Drop
Traffic Shaping
ATM QoS
SNA QoS
Line Protocols

  • Cisco IOS Software Command Summary
  • Dial Solutions Quick Configuration Guide
  • System Error Messages
  • Debug Command Reference

 

1This book will not be available until January 1999.

Service and Support

For service and support for a product purchased from a reseller, contact the reseller. Resellers offer a wide variety of Cisco service and support programs, which are described in the section "Service and Support" in the information packet that shipped with your product.


Note      If you purchased your product from a reseller, you can access CCO as a guest. CCO is Cisco Systems' primary real-time support channel. Your reseller offers programs that include direct access to CCO services.


For service and support for a product purchased directly from Cisco, use CCO.

Software Configuration Tips on the Cisco TAC Home Page

For helpful tips on configuring Cisco products, from the CCO home page, click on this path:

Service & Support: Online Technical Support: Technical Tips

"Hot Tips" are popular tips and hints gathered from Cisco's Technical Assistance Center (TAC). Most of these documents are also available from the TAC's Fax-on-Demand service. To access Fax-on-Demand and receive documents at your fax machine, call 888-50-CISCO (888-502-4726). From international areas, call 650-596-4408.

The following sections are provided from the Technical Tips page:

Cisco Connection Online

Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.

CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.

You can access CCO in the following ways:

For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.


Note      If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco's Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.


Documentation CD-ROM

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.

If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.


hometocprevnextglossaryfeedbacksearchhelp
Posted: Fri Jan 17 16:45:23 PST 2003
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.