Table of Contents

Contents
Introduction

How to Use These Release Notes
What Is a Feature Pack?

Feature Pack Components
Product Numbers Quick-Reference List
Feature Pack Overview Table
Feature Set Table

System Requirements

Memory Requirements
Hardware Supported
Software Compatibility
Determining Your Software Release

Installation

Installing Software Images Using the RSL

Recovering from a Connection Error
Restoring the Startup Configuration
Helpful Hints

Loading Cisco IOS Release 11.3 Software on CiscoPro Routers
Alternatives to the RSL

Installing the Router Software Using a TFTP Server Application

Documentation Updates
Related Documentation

Release-Specific Documents
Feature Modules
Hardware-Specific Documentation
Cisco IOS Software Documents

Cisco IOS Documentation Set

Service and Support

Software Configuration Tips on the Cisco TAC Home Page
Upgrading to a New Release

Cisco Connection Online
Documentation CD-ROM

Release Notes for Cisco IOS Release 11.3(5)T Feature Packs for Cisco 4500 and Cisco 4700 Routers

October 19, 1998

These release notes describe the Cisco IOS Release 11.3(5)T feature packs for Cisco 4500 and Cisco 4700 routers.

Contents

These release notes discuss the following topics:

• Introduction

• System Requirements

• Installation

• Documentation Updates

• Related Documentation

• Service and Support

• Cisco Connection Online

• Documentation CD-ROM

Introduction

This section explains how to use this document, describes feature pack components, and has tables that define the aspects of a feature pack.

How to Use These Release Notes

The tables in these release notes contain details about the Cisco feature packs. Use these tables to perform the following tasks before loading a software image onto a router:

1. Use Table 1, "Feature Pack Product Numbers Quick-Reference List," to identify the software image you want to load.

2. Use Table 2, "Cisco 4500/4700 Series Feature Packs," to identify your feature pack and the memory required for your feature set, based on the image you load.

3. Use Table 3, "Cisco IOS Software Feature Sets for the Cisco 4500 and Cisco 4700 Routers," to identify which features are supported in a feature set image.

4. Use Table 4, "Cisco 4500 and Cisco 4700 Default Memory and Upgrade Options," to check the memory required for your feature set, and determine the factory-default memory on the router and the available memory upgrades.

What Is a Feature Pack?

This section describes:

• Feature Pack Components

• Product Numbers Quick-Reference List

• Feature Pack Overview Table

• Feature Set Table

Feature Pack Components

A feature pack is a small box that contains the following items:

• CD-ROM with the following software:

  • Cisco IOS feature set software images that can include bundled modem firmware

  • Router Software Loader (RSL) program (a Windows 95 application)

  • Trivial File Transfer Protocol (TFTP) server application (for Windows 95 only)

• Getting Started with the Router Software Loader CD booklet.

• Release notes that include alternatives to using the RSL for loading software images onto a router

• Software license for using Cisco software in object code form on a single access server or router

• Cisco Documentation CD-ROM that contains all Cisco documentation

The heart of a feature pack is the CD-ROM that contains software images and the Router Software Loader (RSL), which is a Windows 95 application that loads an image onto an access server or router. Each feature pack CD-ROM contains at least one Cisco IOS feature set. The CD booklet, Getting Started with the Router Software Loader, explains how to use the RSL to install the router image. If you cannot use the RSL to load images, you can follow the instructions in the "Alternatives to the RSL" section.

Before running the RSL, read the "Installing Software Images Using the RSL" section. If you are loading software on a preconfigured router, you should save the router configuration file on your PC before beginning the image download process, as described in Getting Started with the Router Software Loader.

Product Numbers Quick-Reference List

Table 1 lists the Cisco product numbers of the feature packs supported in this release

Feature Pack Overview Table

Table 2 identifies each feature pack as specified on the router software CD-ROM label, describes the feature sets in each feature pack, and lists the following: UNIX and DOS filenames of the images, memory requirements, and the RSL installer description.

Feature Set Table

The Cisco IOS software is packaged into feature sets (also called images). Many different feature sets are available, and each feature set contains a specific subset of Cisco IOS features. The following conventions are used to identify feature sets:

• Plus---Value-added feature set with additional features.

• Plus 40---Value-added feature set with additional features, including 40-bit data encryption.

• Plus 56---Value-added feature set with additional features, including 56-bit data encryption.

Cisco IOS images with strong encryption (including, but not limited to, 56-bit DES) are subject to U.S. government export controls and have a limited distribution. Images to be installed outside the U.S. require an export license. Customer orders might be denied or subject to delay due to U.S. government regulations. Contact your sales representative or distributor for more information, or send e-mail to export@cisco.com.

The following list shows which feature sets are supported on the Cisco 4500 and Cisco 4700 series routers. These feature sets only apply to Cisco IOS Release 11.3 T:

• IP

• IP Plus IPSEC 56

• IP Plus

• IP Plus 40

• IP Plus 56

• IP/IPX/AT/DEC

• IP/IPX/AT/DEC Plus

• Enterprise Plus IPSEC 56

• Enterprise Plus

• Enterprise Plus 40

• Enterprise Plus 56

To determine what features are available with each feature set (software image), see Table 3. The table summarizes the features you can use when running a specific feature set on the Cisco 4500 and Cisco 4700 routers for Cisco IOS Release 11.3 T. Table 3 uses these terms:

System Requirements

This section describes the following:

• Memory Requirements

• Hardware Supported

• Software Compatibility

• Determining Your Software Release

Memory Requirements

Table 4 lists the memory delivered by default and the available memory upgrades.

Hardware Supported

The following Cisco routers are supported by Cisco IOS Release 11.3 T:

• Cisco 4000, Cisco 4000-M

• Cisco 4500, Cisco 4500-M

• Cisco 4700, Cisco 4700-M

The following LAN interfaces are supported on Cisco 4500 and Cisco 4700 routers:

• 16-Mbps Token Ring

• 4-Mbps Token Ring

• ATM OC3, DS3, E3

• Ethernet (10BaseT)

• Ethernet (AUI)

• Fast Ethernet (100BaseFX via MII)

• Fast Ethernet (100BaseTX)

• FDDI DAS

• FDDI multimode (DAS/SAS)

• FDDI SAS

• FDDI single-mode

Software Compatibility

The feature packs described in these release notes contain Cisco IOS Release 11.3(5)T software images, some earlier images, and the Router Software Loader (RSL) Version 7.1. Before running the RSL, read the "Installing Software Images Using the RSL" section.

Determining Your Software Release

To view the version of Cisco IOS software that is running on your Cisco 4500 or Cisco 4700 router, log in to the router, and enter the show version user EXEC command:

An output begins similar to the following. The Cisco IOS version appears in the second line.

The output includes more information including processor revision numbers, memory amounts, hardware IDs, and partition information.

Installation

This section provides solutions to problems you might encounter when using the RSL to load Cisco IOS software on a router. It also describes special cases that might require you to load Cisco IOS software on a CiscoPro router or to use an alternative to the RSL.

Installing Software Images Using the RSL

Recovering from a Connection Error

This installation tip provides a possible recovery solution if you are unable to connect to your router. You can skip this section unless you are experiencing a connection error.

In some cases, you might receive the following error message while connecting to the target router:

If you encounter this message, try increasing the Short Timeout value, which is set to 25 seconds, in the Options dialog box, especially if one of the following situations applies:

• You are connecting to a router that has a large configuration file.

• You are connecting to a Cisco AS5200 access server. A Cisco AS5200 requires up to 45 seconds to write a configuration to nonvolatile random-access memory (NVRAM), due to the amount of interfaces that must be checked during this process. Increase the Short Timeout value to 60 seconds.

Restoring the Startup Configuration

In some cases, the RSL is unable to restore the startup configuration. If this happens, take the following steps:

Step 1 Ensure that all cables are properly attached to both the router and the PC.

Step 2 Restart the RSL, and connect by using the Preconfigured router option.

Helpful Hints

The following information about RSL operations can help you with the installation process:

• If you have added any static entries to the PC Address Resolution Protocol (ARP) table, one or more of them might be deleted by the RSL. You need to manually re-enter any deleted entries in the PC ARP table.

• If the router's running configuration at connection time is not the same as its startup configuration, the exact configuration is not restored. Any changes that you have made since the last time a copy running-config startup-config or write memory command was entered are lost.

• The RSL restores the router's startup configuration, but some running configuration commands are not restored. To restore the exact running configuration, reboot the router. The following interface configuration commands are not restored to the running configuration: no shutdown, no ringspeed, and media-type aui.

Loading Cisco IOS Release 11.3 Software on CiscoPro Routers

The RSL has an upgrade utility to permanently modify a CiscoPro router so that it accepts Cisco IOS Release 11.3 software images. The utility changes the router SysObjectID Simple Network Management Protocol (SNMP) MIB value (used for network management) to that of a Cisco router. The software banner also changes and no longer identifies the router as a CiscoPro product.

Alternatives to the RSL

The RSL is designed to work with a PC running Microsoft Windows 95 and is the recommended method for downloading software to the router. The booklet included with the CD-ROM explains how to perform this simple install process. However, an alternative is available for installing router software: using a TFTP server application.

Installing the Router Software Using a TFTP Server Application

Use this TFTP server application method as an alternative to using the RSL to install the router software from the CD-ROM. You can perform this procedure using a PC (running Microsoft Windows 95 or Microsoft Windows 3.1), a Macintosh, or a UNIX system. You can use either the copy tftp flash or copy rcp flash command to download the router software to the router.

First obtain a TFTP application or a remote copy protocol (rcp) application to set up your computer as a TFTP server or an rcp server. Use the RSL or the TFTP server included on the feature pack CD-ROM to install the router software only if you are using a PC running Windows 95. For other operating systems, a number of TFTP or rcp applications are available from independent software vendors or available as shareware from public sources on the World Wide Web.

Step 1 Install any TFTP server application on the PC. (A PC application is included on the feature pack CD-ROM for Microsoft Windows 95 only.)

Step 2 Launch the TFTP server application on the PC, usually by double-clicking the application icon or its .exe filename.

Step 3 Set up the PC as a TFTP server by using the TFTP server application setup or configuration facility.

Most TFTP server applications include a setup facility that allows you to specify the PC as a server. For example, from the TFTP menu of one application, you can select Settings to display a panel that includes a checkbox beside the word Server. To configure the local PC as a server, select this checkbox.

The TFTP server also allows the selection of a root directory. You must select the directory in which the Cisco IOS files reside, for example, d:\cpswinst\images.

Step 4 Establish a console session from your local PC (which is now configured as a TFTP server) to the Cisco router by using one of these methods:

• Connect the PC com port to the router console port.

This is the recommended method. When you reload the router with the new image in Step 25, you remain connected to the router. (If you use Telnet, you lose connection to the router.)

• Establish a Telnet session from the PC to the router.

  Caution Make sure your PC is set up to communicate with the 10BaseT Ethernet port on the router.

Step 5 Connect your PC Ethernet port to the corresponding router LAN port. Use the 10BaseT crossover cable to connect to an Ethernet port. Use straight-through cables if you are connecting via a 10BaseT hub or a 100BaseT hub.

---

Note We recommend that you back up the router configuration before upgrading the router software.

---

Step 6 Enter the following commands to set the configuration register to 0x2101 and reload to the bootstrap image:

Router# configure terminal Router(config)# config-reg 0x2101 Router(config)# end Router# reload

Step 7 Enter yes in response to the prompt asking if the system configuration has been modified:

# System configuration has been modified. Save? yes

Step 8 If the password prompt appears, enter the password.

Password: <password>

Step 9 At the router prompt, enter enable and then the password:

Router(boot)> enable Password: <password>

Step 10 If you are not upgrading a CiscoPro 4000 series router, go to Step 19.

Step 11 At the router prompt, enter the following command to copy the router upgrade utility from the PC CD-ROM drive to the router:

Step 13 When prompted, enter the filename of the image to be copied to the router as in the following example:

Step 16 Enter the reload command to reload the router:

Step 19 At the router prompt, enter the following command to copy the new software image from the PC CD-ROM drive to the router:

Step 20 When prompted, enter the IP address of your PC, as in the following example:

This example specifies the DOS image name of the IP feature set for Cisco 4000 or 4500 series routers. (See Table 2 in the "Feature Pack Overview Table" section).

Step 22 In response to the prompt, enter the destination UNIX image filename, and press Enter.

This is the name of the image file on the router, not the full pathname of the image on the CD-ROM attached to the PC. Refer to Table 2 in the "Feature Pack Overview Table" section for the UNIX image filename.

Destination file name [80281005.bin]? c4500-i-mz.113-5.P

During the transfer process, the software displays messages indicating that it has accessed the file you have specified and is loading it.

Step 23 Enter yes in response to the prompt asking if you want to erase the existing image copy resident in the router Flash memory before copying the new one:

Erase flash device before writing? [confirm] yes

The entire copying process takes several minutes and differs from network to network.

An exclamation point (!) indicates that the copy process is taking place. Each exclamation point (!) indicates that ten packets have been transferred successfully. A checksum verification of the image occurs after the image is written to Flash memory.

Step 24 Enter the following commands to reset the configuration register to 0x2102:

Router(boot)(config)# configure terminal Router(boot)(config)# config-reg 0x2102 Router(boot)(config)# end

Step 25 Enter the reload command to reload the router:

Documentation Updates

Due to a production problem, many source-route bridging commands were omitted from the printed version of the Cisco IOS Software Command Summary (78-4746-xx, DOC-CIOSCS11.2=). For complete documentation of all source-route bridging commands, refer to the Bridging and IBM Networking Command Reference (78-4743-xx). You can also obtain the most current documentation on the Documentation CD-ROM or Cisco Connection Online (CCO).

Related Documentation

This section describes the documentation related to the Cisco 4500 and Cisco 4700 routers, typically including hardware installation guides, software installation guides, Cisco IOS configuration and command references, system error messages, and feature modules that are updates to the Cisco IOS documentation set. Documentation is available as printed manuals or electronic documents, except for the feature modules that are available online only.

The most up-to-date documentation can be found on the Web via Cisco Connection Online (CCO) and on the latest Documentation CD-ROM. These electronic documents might contain updates and modifications made after the paper documents were printed. For information on CCO, refer to the "Cisco Connection Online" section later in this document. For more information on to the CD-ROM, refer to the "Documentation CD-ROM" section later in this document.

Release-Specific Documents

Use these release notes with the following documents:

• Release Notes for Cisco IOS Release 11.3 that contains some feature and caveat information applicable to Cisco IOS Release 11.3(5)T.

• Caveats for Cisco IOS Release 11.3 T that accompanies these release notes.

• Product bulletins; the path is as follows from Cisco Connection Online:

Products and Ordering: More Information: Product Bulletins. Scroll to Software. Under Cisco IOS 11.3, click the Upgrade Paths bulletin. The Upgrade Paths and Packaging Simplification bulletin appears.

Feature Modules

Feature modules describe new features introduced in 11.3 T releases and are updates to the Cisco IOS documentation set. As updates, the features modules are available online only. The feature module information will be added to the Cisco IOS documentation set before the next printing. Feature modules have a brief overview of the feature, benefits, configuration tasks, and a command reference.

To access all the 11.3 T feature modules on CCO, follow this path:

Products and Ordering: Cisco Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.3: Cisco IOS 11.3T New Features.

To access the feature modules on the documentation CD-ROM, follow this path:

Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.3: Cisco IOS 11.3T New Features.

Hardware-Specific Documentation

The following Cisco 4500 and Cisco 4700 documents are available:

• Cisco 4000 Hardware Installation and Maintenance

• Cisco 4000 Series Hardware Installation and Maintenance

• Cisco 4000 Series Installation Guide

• Cisco 4000 Series Configuration Notes

• Release Notes --- Cisco 4000 Series Routers

• Regulatory Compliance and Safety Information

This documentation can be found on CCO and on the Documentation CD-ROM:

• On Cisco Connection Online (CCO), the path is Software & Support: Cisco Documentation: Access Servers and Access Routers: Modular Access Routers: Cisco 4000 Series. For more information, refer to "Cisco Connection Online,".

• On the Documentation CD, the path is Access Servers and Access Routers: Modular Access Routers: Cisco 4000 Series. For more information, refer to "Documentation CD-ROM,".

Cisco IOS Software Documents

The Cisco IOS software documentation is divided into nine modules and two master indexes. There are also four supporting documents.

You can access the Cisco IOS software electronic documents either on Cisco Connection Online (CCO) on the World Wide Web or on the Cisco Documentation CD-ROM:

• On CCO, click Software & Support: Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.3.

• On the Documentation CD-ROM, click Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.3.

The following are some of the types of Cisco IOS Release 11.3 documents available:

• Configuration guides and command references

• Feature descriptions

• Product-specific release notes

• Cisco IOS software caveats

New online navigation enhancements for Release 11.3 include the following:

• Online hot-linked master indexes for configuration guide and command reference documentation sets.

On CCO or on the Documentation CD-ROM, go to Cisco IOS Release 11.3 and click Cisco IOS Release 11.3 Configuration Guides, Command References. Then click Configuration Guide Master Index or Command Reference Master Index. To access documentation related to an index entry, click the page number following the entry.

• Online hot-linked list of features that are new since Release 11.2.

On CCO or the Documentation CD-ROM, go to Cisco IOS Release 11.3 and click Cisco IOS Release 11.3 Configuration Guides, Command References. Next, click Cisco IOS 11.3 New Features.

To access configuration documentation for a feature, do one of the following:

• Click the page number following the feature name. This takes you to the location of the feature document.

• Using your browser search function, search on one or more keywords from the feature name. This brings the feature document to your screen.

For additional information about CCO or the Documentation CD-ROM, refer to the sections ""Cisco Connection Online"" and "Documentation CD-ROM" at the end of these release notes.

Cisco IOS Documentation Set

The Cisco IOS documentation set consists of the following books and chapter topics:

Service and Support

For service and support for a product purchased from a reseller, contact the reseller. Resellers offer a wide variety of Cisco service and support programs, which are described in the section "Service and Support" in the information packet that shipped with your product.

For service and support for a product purchased directly from Cisco, use CCO.

Software Configuration Tips on the Cisco TAC Home Page

The following URL contains links to access helpful tips on configuring your Cisco products:

http://www.cisco.com/kobayashi/serv_tips.shtml

This URL is subject to change without notice. If it changes, point your web browser to http://www.cisco.com/, and follow this path: Software & Support, Technical Tips (button on left margin).

"Hot Tips" are popular tips and hints gathered from the Cisco Technical Assistance Center (TAC). Most of these documents are available from the TAC FAX-on-demand service. To access FAX-on-demand and receive documents at your FAX machine from the USA, call 888-50-CISCO (888-502-4726). From other areas, call 415-596-4408.

The following sections are provided from the Technical Tips page:

• Access Dial Cookbook---Offers easy-to-follow "recipes" for sample router configurations. The first cookbook contains network diagrams, sample configurations, and troubleshooting commands for helping you set up and use dial technologies on Cisco access routers.

• Field Notices---Designed to provide notification of any critical issues regarding Cisco products. These include problem descriptions, safety or security issues, and hardware defects.

• Hardware---Technical Tips related to specific hardware platforms.

• Internetworking Features---Tips on using and deploying Cisco IOS software features and services.

• Sample Configurations---Actual configuration examples complete with topology and annotations.

• Software Products---MultiNet & Cisco Suite 100, Network Management, Cisco IOS Software Bulletins, and CiscoPro Configurations.

• Special Collections---Other Helpful Documents, Frequently Asked Questions, Security Advisories, References & RFCs, Case Studies, and the CiscoPro Documentation CD-ROM.

Upgrading to a New Release

For information on upgrading to a new software release, refer to the Cisco IOS Software Release Upgrade Paths and Packaging Simplification  product bulletin #703 located on CCO. On CCO, follow this path: Products and Ordering: More Information: Product Bulletins. Scroll to Software. Under Cisco IOS 11.3, click the Upgrade Paths bulletin.

Cisco Connection Online

Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.

CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.

You can access CCO in the following ways:

• WWW:  http://www.cisco.com

• WWW:  http://www-europe.cisco.com

• WWW:  http://www-china.cisco.com

• Telnet:  cco.cisco.com

• Modem:  From North America, 408 526-8070; from Europe, 33 1 64 46 40 82. Use the following terminal settings: VT100 emulation; databits: 8; parity: none; stop bits: 1; and connection rates up to 28.8 kbps.

For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.

Documentation CD-ROM

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.

If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.

Posted: Wed Jun 16 13:11:15 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.