Where to Go from Here

The "First-Time Startup" chapter described how to get your communication server started for the first time using the setup command facility. This chapter describes the following tasks:

How to use the setup command facility after first-time startup to review and alter the basic setup configuration
How to boot your communication server (using the streamlined setup command facility) any time your interfaces are down and you want to netboot
Where to go to perform advanced configuration on the communication server

For information about using the EXEC command interpreter, refer to the Access and Communication Servers Configuration Guide. For information about specific commands, refer to the Access and Communication Servers Command Reference publication. For information about making connections to network hosts, refer to the Cisco Access Connection Guide.

Using the Setup Command after First-Time Startup

The setup command facility can be used after first-time startup to make basic changes at any time. The changes you make will affect only the changed elements in current running memory value and in nonvolatile memory NVRAM.

When you enter the setup command facility after first-time startup, you must run through the entire dialog until you come to the element you intend to change. The default values indicated within the brackets in the System Configuration Dialog are the values left as defaults, last set using the setup command facility, or supplied using the configure command. If you do not want to make the change while still in the System Configuration Dialog, press Ctrl-C to return to the privileged EXEC prompt.

Refer to the "Preparing for First-Time Startup" chapter for complete descriptions of the values you can assign each item within the dialog.

Using the Streamlined Setup Command Facility

The streamlined setup command facility permits your communication server to netboot an image even though there could be problems with the configuration in NVRAM. The streamlined setup command facility is available only if your system is running from ROM monitor and it has RXBOOT ROMs installed.

The streamlined setup command facility is different from the standard setup command facility in that the streamlined facility does not ask you to configure global system parameters. You are prompted only to configure interface parameters, which permit your communication server to boot.

The communication server enters the streamlined setup command facility if, after any of the following circumstances occurs, your communication server is accidentally or intentionally rebooted (or you are attempting to netboot):

You issued a write erase command, thereby deleting the configuration file in NVRAM.
You have bit 6 (ignore NVRAM configuration) set in the configuration register.
Your configuration in NVRAM has been corrupted.

Example

The following example shows a communication server entering the streamlined setup command facility because the communication server is being netbooted and it does not have a valid image in NVRAM:


          --- System Configuration Dialog ---
Refer to the 'Getting Started' Guide for additional help.
Default settings are in square brackets '[]'.
Configuring interface IP parameters for netbooting:
Configuring interface Ethernet0:
  Is this interface in use? [yes]:
    IP address for this interface: 131.108.169.23
    Number of bits in subnet field [0]: 8
    Class B network is 131.108.0.0, 8 subnet bits; mask is
    255.255.255.0

Note The message "Configuring interface IP parameters for netbooting" only appears if you are netbooting and your configuration has insufficient IP information.

: You are asked to provide an IP address and subnet mask bits. You can enter the subnet mask bits as a decimal value such as 8.
: The configuration information you provide at this screen is temporary and exists only so that you can proceed with booting your system. When you reload the system, your original configuration is left intact. If your image in NVRAM is corrupted, enter the setup command facility, configure the basic parameters, then issue the write memory command to write this configuration to NVRAM. Refer to the Access and Communication Servers Configuration Guide for further details. Refer to the Access and Communication Servers Command Reference publication for information about specific commands.

Reviewing the Modifications to the Configuration

You can review the changes you have made to the configuration. To display information stored in NVRAM, use the EXEC command show configuration. To make changes, use the configure command as described in the Access and Communication Servers Configuration Guide.

Implementing Other Configuration Tasks

After you establish the basic startup configuration for your communication server, refer to the Access and Communication Servers Configuration Guide for information about using the configure command to make advanced configuration changes.

The configuration guide also provides information about the following tasks:

Booting and rebooting the communication server
Setting the configuration register
Loading configuration files or system images using TFTP
Reloading the operating system

Table of Contents