cc/td/doc/product/rtrmgmt/ism/ism_v2r2
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table Of Contents

ISM Messages


ISM Messages


This appendix describes messages for ISM and recommends actions you can take to resolve the conditions indicated by the message. The messages are listed in alphanumeric order.

To get specific information about an error message from within the ISM program, position the cursor on a message and press PF1. You can also use the ismhmsg command from any ISM command line to get ISM message help.


Note ISM uses the prefix NSP for all messages.

Some messages contain site-specific data, represented in this appendix by values such as parm.2 and parm.3.


Error Message    NSP1001I PF Key not supported.

Explanation    You pressed a function key that is not supported from this panel. Only those function keys displayed at the bottom of the panel are supported.

Recommended Action    Verify the action you are attempting to perform and select the appropriate function key from those displayed at the bottom of the panel.

Error Message    NSP1002I Operator parm.2, is not the authorized ISM Manager. parm.3 is the correct manager.

Explanation    This message is created when an operator other than the designated operator issues the isminit command.

Recommended Action    Issue the isminit reset command to reset ISM. At a NetView command prompt, issue the autotask opid=ismmgr command, where ismmgr is the designated installation autotask for ISM manager.

Error Message    NSP1003I ISM Initialization was done at parm.2.

Explanation    This message occurs when an operator issues the isminit command without a correct option.

Recommended Action    Issue the isminit reset command to reset ISM. At a NetView command prompt, issue the autotask opid=ismmgr command, where ismmgr is the designated installation autotask for ISM manager.

Error Message    NSP1005E Build for parm.2 failed, parameter = parmlist.

Explanation    This message is generated when incorrect data is passed to either the NSPIBCV4 or NSPIBCF3 routines.

Recommended Action    Enable the TRFLOW service aid in ISM to find out what data is being passed internally as the routines are executed.

Error Message    NSP1006I ISM storage resident routines loaded by parm.2

Explanation    This message is generated when routine NSPILD4 is executed.

Recommended Action    None.

Error Message    NSP1007I There is no previous panel.

Explanation    You requested to view a previous panel of information when none exists. Previous panels exist only if PF7 is displayed at the bottom of the panel.

Recommended Action    None.

Error Message    NSP1008I There is no continuation panel.

Explanation    You requested to view a continuation panel of information when none exists. Continuation panels exist only if PF8 is displayed at the bottom of the panel.

Recommended Action    None.

Error Message    NSP1009I Cursor not on a valid line.

Explanation    You pressed Enter when the cursor is not positioned in a valid location on the panel.

Recommended Action    Ensure that the cursor is positioned in a valid location and press Enter.

Error Message    NSP1010I You are at the left most panel.

Explanation    You pressed PF10 to request to view additional data on the left side of the panel when none exists.

Recommended Action    None.

Error Message    NSP1011I You are at the right most panel.

Explanation    You pressed PF11 to view additional data on the right side of the panel when none exists.

Recommended Action    None.

Error Message    NSP1012I No command to retrieve.

Explanation    You requested to retrieve archived commands when all previously issued commands were already retrieved.

Recommended Action    None.

Error Message    NSP1013E parm.2 command canceled by operator.

Explanation    An issued runcmd was terminated by an operator who issued a cancmd against the service point of the resource to which the runcmd was issued.

Recommended Action    Check the NetView log to verify that a cancmd was issued.

Error Message    NSP1014E VTAM reported error, parm.2 not responding. See the NetView log.

Recommended Action    This message indicates that the service point you specified is not available to VTAM. This failure can be caused by one of the following:

Service point not known to VTAM (DSI358I)

Service point not active to VTAM (DSI264I)

Service point rejects the RUNCMD (DWO614E)

Recommended Action    View the NetView log for the reason for this failure.

Error Message    NSP1015I VTAM DSPU name is required.

Explanation    You requested to perform an action that requires a VTAM DSPU name and you did not specify one.

Recommended Action    Specify a valid VTAM DSPU name and resubmit your request.

Error Message    NSP1016I VTAM PU name required.

Explanation    You are defining a DSPU resource and are being prompted to specify the DSPU name (VTAM PU name) of the resource. This is a required field.

Recommended Action    Specify a valid DSPU name (VTAM PU name) and press Enter.

Error Message    NSP1017E Error for VTAM command parm.2.

Explanation    The NSPRVDIS routine experienced a VTAM command failure when attempting to determine the VTAM status of a resource.

Recommended Action    Display the VTAM resource to confirm the error.

Error Message    NSP1018E Timeout for VTAM command parm.2.

Explanation    The NSPRVDI3 routine did not receive a response from VTAM within 20 seconds. Timeout occurs after 20 seconds.

Recommended Action    Display the VTAM resource to confirm the error.

Error Message    NSP1019I VTAM node definition not specified.

Explanation    You attempted to create a resource definition without specifying a VTAM node definition.

Recommended Action    Verify that you created a PU definition in VTAM for the resource.

Error Message    NSP1020E Bad return code from RUNCMD. Return Code = parm.2.

Explanation    A runcmd that was issued to a resource has failed. The NetView log may contain information that can help determine the cause of this failure.

Recommended Action    View the NetView messages logged for that resource to determine the possible actions that should be taken. If you are unable to determine the cause of the failure, contact network support for assistance with this error.

Error Message    NSP1021I Cisco resource interface parm.2 management initialization started.

Explanation    The request to initialize an interface type was received and the ISMIINIT routine is building the environment to manage that interface type.

Recommended Action    None.

Error Message    NSP1022I parm.2 parm.3 management initialization completed.

Explanation    The request to initialize an interface type was received and completed by ISM.

Recommended Action    None.

Error Message    NSP1023I Cisco resource management initialization started.

Explanation    This message is logged when the ISM initialization is started by the ISMINIT routine.

Recommended Action    None.

Error Message    NSP1024I Cisco resource management initialization completed. Entries = parm.2.

Explanation    This message is logged when the ISM initialization is completed by the ISMINIT routine. The number displayed in the Entries field is the number of resources being monitored by ISM.

Recommended Action    None.

Error Message    NSP1025E Help not available.

Explanation    You requested help for a function that does not have help information.

Recommended Action    None.

Error Message    NSP1026E Enter ISMIINIT parm.2 INIT to re-initialize.

Explanation    The ISMIINIT routine was issued to initialize a type of interface when the ISMIINIT routine was already used to initialize the interface.

Recommended Action    If necessary, issue the ismiinit init command to re-initialize the interface type.

Error Message    NSP1027E Enter ISMINIT INIT to re-initialize.

Explanation    The ISMINIT routine was issued to initialize ISM, when the ISMINIT routine was already used to initialize ISM.

Recommended Action    Issue the excmd ismmgr isminit init command. The ISMINIT routine should be executed only by the ISMMGR autotask. If an operator issues the isminit init command, that operator takes over the functions of ISMMGR.

Error Message    NSP1029E parm.2 interface initialization failed.

Explanation    The interface initialization failed for the interface parm.2.

Recommended Action    Browse the NetView log for >NSPIIN4. The reason for the failure is explained in the text following this header in the log.

Error Message    NSP1030I parm.2 interface initialization was done at parm.3.

Explanation    The ISMIINIT routine was issued to initialize a specific type of interface when that interface was already initialized.

Recommended Action    If necessary, issue the ismiinit n init command, where n is the letter that represents the interface type that you want to re-initialize. The values for the types of interfaces you can view are:

A (Async)

B (ISDN)

C (Channel)

D (FastEthernet)

E (Ethernet)

F (FDDI)

G (GigabitEthernet)

H (HSSI)

I (IBM CLAW)

L (Loopback)

M (ATM)

N (MPC)

S (Serial)

T (Token Ring)

U (Tunnel)

Error Message    NSP1031I No ISMDSA data set, initialization will not be done.

Explanation    The VSAM support required for ISM was not available.

Recommended Action    Verify that the ISMDSA task is active.

Error Message    NSP1032E SETUP record not found. Do ISMSETUP before doing a ISMINIT.

Explanation    An attempt was made to initialize ISM before ISMSETUP was performed.

Recommended Action    From the ISM main menu panel, select SETUP. After you specify your setup options, log off the ISMMGR autotask and start the ISMMGR autotask.

Error Message    NSP1034E ISM is not initialized.

Explanation    You attempted to use an ISM routine, but ISM was not initialized. You will receive this message in the following situations:

ISM was not enabled

ISMMGR was not started

Recommended Action    Initialize ISM and retry your request. If ISMMGR is active, look in the log for message NSP1032I (ISM not enabled). Access ISM setup from the ISM main menu panel and press PF10 to show the active ISM variables. If the values for the variables are blank, then ISM setup was not performed. Proceed to enable the ISM management options.

Error Message    NSP1035I You must exit your session with parm.2.

Explanation    You attempted to toggle from the ISM Resource Configuration Collector panel without properly exiting your enabled session. When a resource is enabled to an operator, no other operator can communicate with it.

Recommended Action    To properly exit the enabled session, type EXIT in the Command Input field beneath the Host name field and press Enter. Press PF3 to exit the Resource Command Interface panel.

Error Message    NSP1036E Input error, enter a valid option and press Enter.

Explanation    You entered an option that is not available on the popup menu.

Recommended Action    Review the Resource Management popup menu, enter a valid option, and press Enter.

Error Message    NSP1037I Make changes and press Enter to validate.

Explanation    You are authorized to make changes to the data displayed on this panel.

Recommended Action    If you make changes to the data, press Enter to verify the changes, and press PF4 to save the changes.

Error Message    NSP1038I Press Enter for prompted input.

Explanation    Instructions on specifying values for the fields on this panel are available.

Recommended Action    If necessary, press Enter for instructions on specifying values for the fields on this panel.

Error Message    NSP1039I Press PF4 to go to update mode.

Explanation    You are authorized to make changes to the information displayed on this panel.

Recommended Action    To make changes to a resource, press PF4.

Error Message    NSP1040I Press PF4 to implement changes or PF3 to exit.

Explanation    You made changes to the information displayed on the panel.

Recommended Action    To save and implement the changes you made, press PF4. To exit the panel without implementing or saving the changes, press PF3.

Error Message    NSP1041I Press PF4 to update resource management data.

Explanation    You are authorized to make changes to the information you are viewing on the Resource Management Data panel.

Recommended Action    To begin making changes, press PF4 to display the Cisco Resource Definition.

Error Message    NSP1043I Press PF4 to delete parm.2 setup.

Explanation    You requested to delete the ISM setup by specifying the Delete option in the Change field on the ISM Resource Management Setup panel.

Recommended Action    Ensure that you want to delete the ISM setup. Press PF4 if you are sure that you want to delete the ISM setup.

Error Message    NSP1044I Press PF4 to delete resource.

Explanation    You requested to delete a resource. If this resource is a router, the router definition, router history, interfaces configured in the router and the interface history archived will be deleted. If you are deleting an operator profile, see the Recommended Action.

Recommended Action    If you are deleting an operator profile, issue the ismusers command to ensure that the operator profile that you are deleting is not the only remaining ISM administrator profile. Verify that your request is accurate and press F4 to delete the resource.

Error Message    NSP1046I At least one filter is required.

Explanation    You enabled status filtering by specifying Y in the Status Filters field on the ISM User Administration panel, and have not specified a status type in the Filter 1, 2, or 3 fields.

Recommended Action    To enable status filtering, type Y in the Status Filters field, and specify at least one status type in the Filter 1, 2, or 3 fields. To disable status filtering, type N in the Status Filters field. The following status filters are valid:

ACTIV

INOP

INVALID

PERF

ALERT

CONCT

NONE

UNKNOWN

Error Message    NSP1047I At least one group is required.

Explanation    You enabled group filtering by specifying Y in the Group Filters field on the ISM User Administration panel, but you did not specify a group in the Group 1 or Group 2 fields. Enabling group filtering requires that you specify a group.

Recommended Action    To enable group filtering, type Y in the Group Filters field and specify at least one group in the Group 1 or Group 2 fields. To disable group filtering, type N in the Group Filters field.

Error Message    NSP1048I Description not provided.

Explanation    You are defining a resource and are being prompted for a description. This field is optional and for information only.

Recommended Action    None.

Error Message    NSP1051I Record parm.2 deleted.

Explanation    The VSAM control file of the record you requested to delete was deleted.

Recommended Action    None.

Error Message    NSP1052I Record parm.2 added.

Explanation    The VSAM control file was added or updated with the changes you made.

Recommended Action    None.

Error Message    NSP1054I Collection Complete for parm.2; parm.3 records collected.

Explanation    Your request to collect and archive the current configuration of the resource was successfully completed.

Recommended Action    None.

Error Message    NSP1055E Delete failed for record parm.2; Return Code = parm.3.

Explanation    Your request to delete a record failed. This message indicates that the routine NSPVSAM4 was unsuccessful when attempting to delete a VSAM control file. A return code 1 indicates that the VSAM command timed out. A return code 2, indicates the record was not found.

Recommended Action    Check the NetView log for messages 1098, 1106, 1107, and 1108. If the file was deleted already, this error message is normal.

Error Message    NSP1056I Resource not known: Press Enter for prompted input.

Explanation    The control name of the specified resource is unknown to ISM. However, you are authorized to define the resource to ISM.

Recommended Action    Verify and re-enter the control name if this is a previously defined resource, or press Enter for prompts to define a new resource.

Error Message    NSP1057E Updating failed for record parm.2; Return Code = parm.3.

Explanation    The NSPVSAM4 routine was unable to update a record. If the return code is 1, the routine may be out of VSAM space.

Recommended Action    Check NetView log for messages 1098, 1106 1107 and 1108.

Error Message    NSP1059E Authorization error. parm.2 cannot do a reset.

Explanation    You issued the nspoper3 command to reset a session between an operator and a resource while you are not authorized to perform this action. To reset a session, you must be an enabled ISM user.

Recommended Action    If the session between an operator and resource needs to be reset, find an authorized operator to perform the operation.

Error Message    NSP1060E Unauthorized attempt to execute parm.2.

Explanation    You requested to define, update, or delete a resource interface while you are not authorized to perform this action. To modify a resource interface, you must be an enabled ISM user.

Recommended Action    If the resource interface needs to be modified, find an authorized operator to perform the operation.

Error Message    NSP1061E You are not authorized to change the ISM DSPU environment.

Explanation    You attempted to modify the ISM DSPU environment while you are not authorized to perform this action. To modify the ISM DSPU environment, you must be an enabled ISM user.

Recommended Action    If the ISM DSPU environment needs to be modified, find an authorized operator to perform the operation.

Error Message    NSP1062E You are not authorized to change the ISM Setup environment.

Explanation    You attempted to modify the ISM setup while you are not authorized to perform this action. To modify the ISM setup, you must be an ISM administrator.

Recommended Action    Contact an ISM administrator to perform the operation.

Error Message    NSP1063E You are not authorized.

Explanation    You attempted to perform an action for which you are not authorized.

Recommended Action    Contact an ISM administrator to change your user authority settings.

Error Message    NSP1064I Resource parm.2 already defined.

Explanation    You attempted to define a resource that was already defined to ISM.

Recommended Action    None.

Error Message    NSP1065I Resource 'parm.2' not Known.

Explanation    The resource is not known to ISM.

Recommended Action    Before using this command, define the resource to ISM using ISMCMD.

Error Message    NSP1066I Resource "&parm.2 not a managed resource.

Explanation    The resource is not known to ISM.

Recommended Action    Before using this command, define the resource to ISM using ISMCMD.

Error Message    NSP1067I Resource parm.2 busy; enabled by operator parm.3.

Explanation    You attempted to establish an enabled session with a resource enabled to another operator.

Recommended Action    Ensure that the operator enabled to the resource is logged on by performing a list parm.3. If the operator is not logged on, use the RESETOP option on the Resource Status panel (NSPVMGRT) to reset the session between the resource and operator.

Error Message    NSP1068I Resource parm.2 deleted from ISM manager.

Explanation    The request to delete a resource definition was successfully completed. The message is also written to the NetView log for tracking purposes.

Recommended Action    None.

Error Message    NSP1069I Resource parm.2 not known.

Explanation    You attempted to delete the definition of a resource not known to ISM.

Recommended Action    None.

Error Message    NSP1071I Resource name has bad syntax.

Explanation    The syntax of the control name you specified was incorrect. Control names may be a combination of up to eight alphanumeric characters. Special characters are not valid.

Recommended Action    Verify the control name you entered and re-enter the control name using valid characters.

Error Message    NSP1072I Resource name required.

Explanation    The command requires a resource name.

Recommended Action    Verify that you have entered a resource name and retry the command.

Error Message    NSP1073I Resource unavailable because it is enabled by parm.2.

Explanation    The RUNCMD failed because the resource is enabled by another operator.

Recommended Action    Ensure that the operator enabled to the resource is logged on by performing a list parm.3. If the operator is not logged on, use the RESETOP option on the Resource Status panel (NSPVMGRT) to reset the session between the resource and operator.

Error Message    NSP1074I Resource host name not provided.

Explanation    You are defining a resource and are being prompted to enter the Resource Host Name field. If a VTAM definition currently exists for the resource, this information is automatically obtained.

Recommended Action    None.

Error Message    NSP1075I Last record not found.

Explanation    Your request to retrieve the history records was denied because ISM could not locate the last record.

Recommended Action    None. When the next history record is recorded by ISM, this problem will be corrected.

Error Message    NSP1076I Resource control name is required.

Explanation    You attempted to define a resource without specifying its control name. The control name is up to eight alphanumeric characters and is a required field.

Recommended Action    Specify the control name of the resource and press Enter.

Error Message    NSP1078I parm.2 is not a monitored resource.

Explanation    You bypassed ISM and issued an ISM routine to monitor a resource undefined to ISM. To monitor a resource using ISM routines, the resource must be defined to ISM.

Recommended Action    None.

Error Message    NSP1079I New interface discovered parm.2, parm.3, parm.4.

Explanation    A new interface that was not previously defined to ISM was discovered.

Recommended Action    None.

Error Message    NSP1080I No data available for resource parm.2.

Explanation    A request for the configuration of a resource failed because the configuration for the resource is not stored in NetView variables.

Recommended Action    If you are an enabled ISM user, use Option 7 on the popup menu to collect the current resource configuration.

Error Message    NSP1081I Now collecting interface data for resource parm.2.

Explanation    The ISM ISMISTAT routine is collecting data from the interfaces to be monitored by ISM.

Recommended Action    None.

Error Message    NSP1082I Now collecting interface status for resource parm.2.

Explanation    The ISM NSPISTAT routine is collecting status data for the specified interface. This message occurs only when the ISMAID DEBUG facility is set to YES.

Recommended Action    None.

Error Message    NSP1084I Resource configuration saved for parm.2.

Explanation    The resource configuration you collected was successfully archived.

Recommended Action    None.

Error Message    NSP1085I Configuration management options not specified.

Explanation    You are defining a resource and are being prompted to enter its IP address. This field is optional and for information only.

Recommended Action    None.

Error Message    NSP1086I No Response from retrieve.

Explanation    You requested data from a resource and the resource did not respond.

Recommended Action    Issue the ismr resource-name command. Use the options to diagnose the problem.

Error Message    NSP1087I IP address not provided.

Explanation    You are defining a resource and are being prompted to enter its IP address. This message is for information only.

Recommended Action    None.

Error Message    NSP1088I Request to delete history records issued.

Explanation    Your request to delete interface history records was issued.

Recommended Action    None.

Error Message    NSP1091E Database not defined.

Explanation    The internal routine NSPVSAM4 was called by ISM with the incorrect parameters. This error message indicates an ISM routine error, not a user error.

Recommended Action    None.

Error Message    NSP1092I Database now being updated for parm.2.

Explanation    This message is created after every 40 records are saved in the VSAM configuration data base.

Recommended Action    None.

Error Message    NSP1095I No data found in NSPDB data base for parm.2.

Explanation    The calling routine could not find VSAM records required by the routine. The records may have been deleted earlier or are not yet available.

Recommended Action    None.

Error Message    NSP1096I No NSPDSA task, start NSPDSA task and retry. Error Message    Explanation ISM attempted to retrieve configuration data from the "A" VSAM data base and failed.

Recommended Action    Verify that the task NSPDSA is active and try again.

Error Message    NSP1097I Timeout- the wait operation used to collect data timed out.

Explanation    A command sent to a router did not return a response within the expected time.

Recommended Action    Action Verify that the router is active and responding to commands.

Error Message    NSP1098E NSPDS failed, message = parm2.

Explanation    A VSAM request for ISM data failed.

Recommended Action    The data that follows this message indicates the reason for the failure.

Error Message    NSP1099E VSAM update error. Error = parm.2.

Explanation    The ISM NSPSCON3 routine received a VSAM error while saving a resource configuration.

Recommended Action    The data that follows this message indicates the reason for the failure.

Error Message    NSP1090I No input was passed with command.

Explanation    The internal routine NSPADDM or NSPADDN was called with no parameters. This indicates an ISM internal error, not a user error.

Recommended Action    None

Error Message    NSP1100I There is no operator monitoring parm.2.

Explanation    You requested to reset a session between a resource and an operator by issuing the nspoper3 command without specifying an operator ID, or by using the RESETOP function key on a resource not currently in a session with an operator.

Recommended Action    View the Resource Status panel to verify that a session is established between the resource and an operator and, if so, reset the session by issuing the nspoper3 command and specifying the resource name and operator ID or by using the RESETOP function key.

Error Message    NSP1103I Trace Data >> parmlist.

Explanation    This message is written to the log when the ISMAID service aid DEBUG is turned on.

Recommended Action    None.

Error Message    NSP1104I Module Entry Trace >> parmlist.

Explanation    This message is displayed only when the ISMAID service aid TRFLOW is set to ON. It contains the data passed to the routine when it is called.

Recommended Action    None.

Error Message    NSP1105I Module Exit Trace >> parmlist.

Explanation    This message is displayed only when the ISMAID service aid TRFLOW is set to ON. It contains the data and error conditions from the routine's exit.

Recommended Action    None.

Error Message    NSP1106E Command parm.2 failed. Operator replied GO.

Explanation    This error message occurs if a WAIT command is terminated by the operator entering GO from a NetView command line. The WAIT command should have an internal timeout value and indicate a timeout when the WAIT function fails.

Recommended Action    Retry the routine and see if the problem recurs.

Error Message    NSP1108E Command parm.2 timed out.

Explanation    The command specified in the message has timed out.

Recommended Action    Re-issue the command. If the failure recurs, contact your NetView system programmer for assistance.

Error Message    NSP1111E Requires session to be enabled.

Explanation    You requested to collect the current configuration of a resource by issuing the nspgetc3 command without establishing an enabled session with that resource.

Recommended Action    If you are an authorized enabled ISM user, use Option 7 on the resource options menu to establish an enabled session with the resource and collect the current configuration.

Error Message    NSP1112E Status Collection complete for parm.2, Number of interface = parm.3.

Explanation    Your request to collect information about the interfaces configured in a resource by issuing the ismistat command was successful. This message appears only if the ISMAID service aid is set to on. The number of interfaces discovered is also displayed in this message.

Recommended Action    None.

Error Message    NSP1113I Insufficient number of parameters passed with command.

Explanation    A routine could not execute because of insufficient input parameters.

Recommended Action    If the routine was called via another routine, turn on the ISMAID TRFLOW service aid and repeat the action.

Error Message    NSP1116I Operator parm.2 not known.

Explanation    You are not defined as an ISM user. This message is generated when you perform an ISM function and ISM verifies that your operator ID is defined to ISM (via an ISM profile). All functions performed using ISM are monitored, and this message is displayed as long as you are undefined to ISM.

Recommended Action    Have an ISM administrator create an operator profile using the USER option available on the ISM main menu.

Error Message    NSP1117I Operator Group ID not specified.

Explanation    You are defining a resource and are being prompted to specify a group to which this resource belongs in the Operation Group ID field. Operator groups may be all resources located in a region or department, or resources of a particular device type. You can filter resources by the Operation Group. This field is optional.

Recommended Action    None.

Error Message    NSP1118I Operator ID required.

Explanation    You attempted to create an operator profile without specifying a name in the Operator Name field.

Recommended Action    Specify the name of the operator in the Operator Name field and resubmit your request.

Error Message    NSP1119I Operator parm.2 is no longer router manager for parm.3.

Explanation    This message is created when the nspoper3 command is issued against the specific service point and an enabled operator was managing the resource.

Recommended Action    None.

Error Message    NSP1120I All values have been reset for ISM by parm.2.

Explanation    This message is displayed when the isminit command was issued with the reset option specified. The isminit reset command clears all variables associated with managing the resources.

Recommended Action    Issue the isminit command to rebuild the variables.

Error Message    NSP1121I Entered with invalid value for parm.2.

Explanation    The NSPHIST4 command was issued with an invalid value specified. NSPHIST4 is the command history recording routine.

Recommended Action    Verify the values specified and resubmit your request.

Error Message    NSP1122I Entered with invalid parameters: parm.2.

Explanation    The NSPHIST4 command was issued with invalid parameters. NSPHIST4 is the command history recording routine.

Recommended Action    Verify the specified parameters and resubmit your request.

Error Message    NSP1124I Input not found at row = parm.2, column = parm.3.

Explanation    The cursor is in a position on the panel that does not contain the required data for processing.

Recommended Action    Verify that all required data was specified and resubmit your request.

Error Message    NSP1126E Invalid resource name parm.2 given.

Explanation    The resource name passed with the NSPRVDI3 routine is unknown to VTAM.

Recommended Action    Ensure that the resource is properly defined to VTAM.

Error Message    NSP1129I CTRACE set to >parm.2<

Explanation    The current ISMAID service aid settings are those identified in this message. This message is for information only.

Recommended Action    None.

Error Message    NSP1131E SAFE failed, Message = parm.2.

Explanation    The request to retrieve resource history data (NSPRDI4 routine) has failed.

Recommended Action    Contact your system programmer.

Error Message    NSP1132I Action type must be either 1, 2, or 3.

Explanation    You attempted to make changes without specifying whether you want to implement your changes at the next startup of ISM, implement them in the current session only, or implement them in the current session and save the changes for future ISM sessions.

Recommended Action    Enter the number representing the action you want to perform in the Action Type field:

Option 1 means the changes take effect when the function is initialized.

Option 2 means the changes are temporary and apply to only the active variables and are to be used immediately.

Option 3 updates the current values and the VSAM record for the next initialization.

Error Message    NSP1133I Change type must be either 1, 2, or 3.

Explanation    You attempted to make changes without specifying whether you are defining a new resource, updating an existing resource, or deleting a resource.

Recommended Action    Type the number representing the type of change you wish to make in the Change Type field.

Error Message    NSP1134I Change type must be either 2 or 3.

Explanation    You made changes to a panel without specifying the type in the Change Type field. You must specify 2 for update or 3 for delete.

Recommended Action    Specify a type in the Change Type field, and resubmit your request.

Error Message    NSP1135I Resource not known: Press PF3 to exit.

Explanation    The service point name you entered is not a resource known or managed by ISM.

Recommended Action    Verify the control name of the resource for which you attempted to display management data. If the resource is valid but not defined to ISM, contact an ISM administrator to define the resource.

Error Message    NSP1136I Resource not known: Press PF4 to define router.

Explanation    The control name you entered is not a resource known or managed by ISM. However, you are authorized to define a new resource.

Recommended Action    Verify the service point name of the resource for which you are attempting to display management data. If the resource is not known to ISM, press PF4 to define the resource.

Error Message    NSP1139I DSPU Host name is required.

Explanation    You are defining a DSPU resource and are being prompted to specify the DSPU host name of the resource. This is a required field.

Recommended Action    Specify a valid DSPU host name and press Enter.

Error Message    NSP1141E parm.1 parameter should be CTRACE, DEBUG, TRFLOW, or OFF.

Explanation    You issued the ismaid command and specified a parameter other than CTRACE, DEBUG, TRFLOW, or OFF.

Recommended Action    Re-issue the ismaid command with one of the above parameters or, to display help on using the ISM service aid type ismaid.

Error Message    NSP1142I Please enter the parm.2 parm.3.

Explanation    You attempted to execute an ISM routine without specifying the required parameters.

Recommended Action    Re-issue the routine and ensure that you specify all required parameters.

Error Message    NSP1143I Select option number and press Enter.

Explanation    You are on a panel from which you can perform a function by selecting an option number.

Recommended Action    Enter an option number from the list displayed on the panel. The input will be examined starting at the first character position.

Error Message    NSP1144E Input parm.2 not recognized.

Explanation    The routine does not recognize the input.

Recommended Action    Verify the purpose of the routine and retry with different input.

Error Message    NSP1145I parm.2; Press PF6 to return.

Explanation    This message is displayed on NetView panels when you press PF6 on an ISM panel. The field that follows the message ID identifies the ISM routine that is suspended until you press PF6 again to return to an ISM screen.

Recommended Action    None.

Error Message    NSP1146I Router parm.2 not active to VTAM.

Explanation    The ISM status of the resource indicates that the resource is not ACTIV to VTAM.

Recommended Action    Display the Resource Status panel, select the resource, and press Enter. Select Option 5 on the popup menu to view the resource from VTAM. If the status is ACTIV, press PF3 and select Option 9 from the popup menu to reset the status of the resource status. ISM will check the availability of the resource.

Error Message    NSP1147I Service point parm.2 already managed by operation_id.

Explanation    You are attempting to establish a session with, or issue commands to, a resource currently in a session with another operator. The ID of the operator busy with the resource is displayed in this message.

Recommended Action    Display the Resource Status panel to view the operator ID. If the operator is not logged on and you are an enabled ISM user, you can reset the session. To do so, position the cursor on the service point name or operator ID and press PF9.

Error Message    NSP1148I More data available, press PF8. Enter N to terminate.

Explanation    You issued the show mem command and there are additional pages of data. The Host name field contains the word "More" when more data is pending from the resource.

Recommended Action    To view the additional pages of data, press PF8, or to terminate the display, type N.

Error Message    NSP1149I Router command parm.2 cannot be used with service point interface.

Explanation    The command you issued cannot be executed through the resource service point at this time. The command you issued is one of a group that provides output to the operator at a later time. The service point does not support asynchronous operations at this time. There is no way for the unsolicited responses to be sent back to the operator who issued the command. For example, telnet is a command that should not be sent to the resource.

Recommended Action    To connect directly to the resource, use a local console or Telnet via a TCP/IP session.

Error Message    NSP1150I Enter password.

Explanation    You are performing a function that requires you to enter a password to establish an enabled session with the resource.

Recommended Action    To establish the enabled session, enter the enable password exactly as it is defined to the resource. If you do not know the enable password, or if you want to cancel the enable request, entering an invalid password three times terminates the enable request.

Error Message    NSP1151I Password field empty, enter password.

Explanation    You attempted to enable to a resource without specifying a password. A password must be specified when requesting an enabled session.

Recommended Action    To establish the enabled session, enter the enable password exactly as it is defined to the resource. If you do not know the enable password and you want to cancel the request, enter an invalid password three times.

Error Message    NSP1152I More data available. Enter Y to continue; N to terminate.

Explanation    You issued the show mem command and you are on the last page of the first set of data returned from the resource. The Host name field contains the word "More" when more data is pending from the resource.

Recommended Action    To display additional data, type Y. To terminate the display, type N.

Error Message    NSP1153I You are not authorized to do an enable.

Explanation    You requested to establish an enabled session with a resource. You are not authorized by an ISM administrator to establish an enabled session.

Recommended Action    Ensure that your ISM user authority settings in your profile are correct. If the settings are not correct, contact an ISM administrator to change them.

Error Message    NSP1154I Press PF3 to terminate enable.

Explanation    You are currently in an enabled session with the resource. While you are enabled to the resource, no other operator can communicate with the resource.

Recommended Action    To properly terminate the enabled session, press PF3. Pressing PF3 terminates your enabled session with the resource by sending an EXIT RUNCMD to the resource. This RUNCMD frees the resource for other operator use.

Error Message    NSP1155I Input parameter parm.2 should be a numeric value.

Explanation    A non-numeric value was detected by the NSPMCHK4 routine. The NSPMCHK4 routine calculates the free resource memory based on the values collected from the resource.

Recommended Action    None.

Error Message    NSP1157I parm.2 parm.3 parm.4 has been executed by parm.5.

Explanation    This message indicates that the ismiinit command was issued with the RESET option. This message is for monitoring purposes only.

Recommended Action    None.

Error Message    NSP1158I Config DB save started for parm.2 parm.3.

Explanation    The resource configuration you just collected is now being stored in the VSAM configuration data base.

Recommended Action    None.

Error Message    NSP1159E Unexpected output from VTAM parmlist.

Explanation    You requested to view the resource as defined to VTAM, and the output from VTAM was not recognizable.

Recommended Action    Issue the command displayed in this message and check the output. If the output is recognizable, but your request for the VTAM resource configuration fails again, consult your NetView support.

Error Message    NSP1160I parm.2 is no longer enabled to or controlling parm.3, reset by parm.4.

Explanation    If you requested to reset an enabled session between a resource and operator, this message indicates that your request has completed successfully. If you received this message while in a session with a resource, it indicates that the session between you and the resource was terminated.

Recommended Action    None.

Error Message    NSP1161I parm.2 no longer is busy with router parm.3.

Explanation    Your request to reset a busy session between an operator and a resource has completed successfully.

Recommended Action    None.

Error Message    NSP1162I Operator has been changed, origin = parm.2, New = parm.3.

Explanation    You requested to reset a session between an operator and resource, and the operator you specified is no longer the current operator. This indicates that the busy condition no longer exists for the specified resource, or that a new operator has established a session with the resource.

Recommended Action    Display the Resource Status panel to verify the operator, if any, that may be enabled to, or busy with, the resource.

Error Message    NSP1163I parm.2 interface records deleted for parm.3.

Explanation    Your request to delete the performance or history records for an interface has completed successfully.

Recommended Action    None.

Error Message    NSP1164I An interface type of A, M, C, E, D, F, H, B, L, S, T, U, G, N, or I is required.

Explanation    You requested to view a list of interfaces monitored in the network by type and you did not specify an interface type.

Recommended Action    Specify a type in the Interface Type field and resubmit your request. Valid values are:

A (Async)

B (ISDN)

C (Channel)

D (FastEthernet)

E (Ethernet)

F (FDDI)

G (GigabitEthernet)

H (HSSI)

I (IBM CLAW)

L (Loopback)

M (ATM)

N (MPC)

S (Serial)

T (Token Ring)

U (Tunnel)

Error Message    NSP1165I There is no parm.2 available for parm.3 on parm.4.

Explanation    You requested to view the performance or history data archived for a specific interface for which no data was archived.

Recommended Action    None.

Error Message    NSP1166I 15 minutes is the minimum interval.

Explanation    You set the resource monitoring interval to less than 15 minutes on the ISM Resource Management Setup panel. The minimum interval for resource monitoring is 15 minutes. The interval will be set to 15 minutes.

Recommended Action    Reset the resource monitoring interval to a value of 15 minutes, or longer, or accept the ISM minimum default of 15 minutes.

Error Message    NSP1167I Router status refresh request sent to ISMMGR.

Explanation    Your request to refresh the status of the resources on the Resource Status panels was sent to ISM.

Recommended Action    Wait for the ISM to query and collect the status of the resources and then press PF12 to view the updated status.

Error Message    NSP1168I There are no parm.2 interfaces for parm.3.

Explanation    You requested to view a list of a specific type of interfaces configured in a resource, and the interfaces were not configured or discovered in that resource.

Recommended Action    None.

Error Message    NSP1169I Interface type parm.2 not initialized.

Explanation    You requested to view the status of a specific interface type that was not initialized.

Recommended Action    To initialize the interface type, issue ismiinit n init, where n is the type of interface you want to initialize. Valid values are:

A (Async)

B (ISDN)

C (Channel)

D (FastEthernet)

E (Ethernet)

F (FDDI)

G (GigabitEthernet)

H (HSSI)

I (IBM CLAW)

L (Loopback)

M (ATM)

N (MPC)

S (Serial)

T (Token Ring)

U (Tunnel)

Error Message    NSP1170I Router busy with operator parm.2.

Explanation    You attempted to issue a RUNCMD to a resource in an enabled or busy session with another operator. The RUNCMD you issued is attempted for 10 seconds before this message is generated.

Recommended Action    If you are an enabled ISM user, you can terminate the session between a resource and an operator from the Resource Status panel. To do so, position the cursor on the operator ID and press PF9. If you get this message each time you attempt to issue the RUNCMD to the resource, display the Resource Status panel to view the operator in an enabled or busy session with the resource.

Error Message    NSP1171I No changes have been made to parm.2.

Explanation    You exited the ISM setup without making changes.

Recommended Action    If you intended to make changes to the ISM setup, make the changes again and press Enter to verify your changes and press PF4 to save your changes and exit the ISM setup.

Error Message    NSP1172E RUNCMD Time-out, parm.2 not responding; See the NetView log.

Explanation    You issued a runcmd command to an unresponsive resource. This error generally indicates an internal problem that prevents the resource from responding to the RUNCMD.

Recommended Action    Verify that the resource service point is configured properly, and that it is defined as a PU to VTAM.

Error Message    NSP1173I Screen copied to log.

Explanation    Your request to copy the information on the panel to a log by pressing PF5 was processed successfully.

Recommended Action    None.

Error Message    NSP1177I Interface State Change parmlist

Explanation    This message is written to the event log when an interface has a state change. The last parameter identifies the routine that created the message.

Recommended Action    Issue the ismr resource-name command to check the resource status.

Error Message    NSP1178I Resource State Change parmlist

Explanation    This message is written to the event log when a resource has a state change. The last parameter identifies the routine that created the message.

Recommended Action    Issue the ismr resource-name command to check the resource status.

Error Message    NSP1186I Position cursor on resource and press PF5 to diagnose status.

Explanation    By pressing PF5, the status of the resource will be analyzed and the appropriate action will be taken to assist in diagnosing the reason for the status condition.

Recommended Action    Press PF3 and then press PF1 to get help on the meaning of the status colors.

Error Message    NSP1187I Press PF5 to diagnose the current status of the resource.

Explanation    By pressing PF5, the status will be analyzed and the appropriate action will be taken to assist in diagnosing the reason for the status condition.

Recommended Action    Press PF3 and then press PF1 to get help on the meaning of the status colors.

Error Message    NSP1188I Position cursor on target and press enter to view target summary.

Explanation    This operation should display the same ISMSUM data presented on the target system by a local operator.

Recommended Action    None.

Error Message    NSP1189I Operator parm.2 of domain parm.3 has changed status of parm.4 from parm.5 to parm.6.

Explanation    This message is created to provide an audit trail of operator actions that affect monitored resource status.

Recommended Action    None.

Error Message    NSP1200I Operator xxx of domain cccc has issued a REFRESH/RESET for resource ssss.

Explanation    This message is written when an operator enters option 9 from the Resource Status with Options menu. This message is part of the audit trail for ISM managed resources.

Recommended Action    None.

Error Message    NSP1201I Command or option is not supported by this resource.

Explanation    This message indicates an operator error.

Recommended Action    Use a different command or option.

Error Message    NSP1202I No data available for this selection.

Explanation    The called routine was unable to find any resources that matched the input status. The status could have changed, but the status panel was not yet updated.

Recommended Action    Press the refresh option if available.

Error Message    NSP1203I There are no resources that match your viewing filters.

Explanation    The called routine was unable to find any resources that matched your viewing filters. You may have group filters that allow you to view only specific resources and related resources.

Recommended Action    Issue the ismuser command to display your filter definitions.

Error Message    NSP1204I Resource parm.2 has been changed by parm.3.

Explanation    This message is used to provide an audit trail. When an operator changes a control file for a monitored resource, a message is written to the ISM event log.

Recommended Action    None.

Error Message    NSP1205I Place cursor on path and press enter to view path statistics.

Explanation    Placing the cursor on a path and pressing enter will display the statistics that have been collected for that path in the channel.

Recommended Action    None.

Error Message    NSP1207I LOGON to target Netview parm.3 to make changes.

Explanation    This function can only be updated at the remote NetView.

Recommended Action    Logon to the remote system and select this function to make changes.

Error Message    NSP1208I Press PF10 to collect configuration.

Explanation    Depressing PF10 will collect the configuration from the router and save it to the VSAM data base.

Recommended Action    None.

Error Message    NSP1209I Changes to target ISM are not allowed.

Explanation    Focal Point management changes can only be made at the local system.

Recommended Action    Logon to the remote system and use ISMSETUP to update or change the FPM environment.

Error Message    NSP1210I Enable time exceeded by parm.2 for router parm.3. Elapsed time = parm.4

Explanation    The operator has remained in enable mode on the router for more than the maximum time allowed. The operator connection to the router has been terminated to allow ISM monitoring to continue.

Recommended Action    None.

Error Message    NSP1211I Unknown resource index parm.2

Explanation    An internal routine has been passed a router number that is not valid. This is an internal logic error.

Recommended Action    If the problem recurs, report it to support.

Error Message    NSP1212I SNMP error: parmlist

Explanation    An SNMP request to a device generated either an invalid number of interfaces or an error. The error text from SNMP is displayed.

Recommended Action    None.

Error Message    NSP1300I TN3270 Management Initialized at parm.2

Explanation    The ISM TN3270 monitoring function has initialized.

Recommended Action    None.

Error Message    NSP1301I TN3270 Management Already Initialized.

Explanation    The ISM TN3270 server monitoring initialization was invoked when the TN3270 monitoring function was already initialized. No action was taken.

Recommended Action    None.

Error Message    NSP1302I TN3270 Management reset by parm.2.

Explanation    The ISM TN3270 server monitoring initialization was restarted by the operator whose id is displayed.

Recommended Action    None.

Error Message    NSP1303I TN3270 Initialization Error:parm.2

Explanation    Initialization of the ISM TN3270 server monitoring failed because the configuration record was not found on the VSAM data base.

Recommended Action    Use ISMSETUP to verify the TN3270 monitoring setup.

Error Message    NSP1330I No TN3270 feature available for parm.2

Explanation    An attempt was made to monitor the tn3270 on parm.2 but no tn3270 server(s) were found configured on the router.

Recommended Action    Verify that the tn3270 on the router is active. If the tn3270 server is no longer configured on the router, use the router management screens to remove tn3270 flag.

Error Message    NSP1400I SNMP Management Initialized at parm.2

Explanation    The ISM SNMP monitoring function has initialized.

Recommended Action    None.

Error Message    NSP1401I SNMP Management Already Initialized.

Explanation    ISM SNMP initialization was invoked when the SNMP function was already initialized. No action was taken.

Recommended Action    None.

Error Message    NSP1402I SNMP Management reset by parm.2.

Explanation    The ISM SNMP management initialization was restarted by the operator whose id is displayed.

Recommended Action    None.

Error Message    NSP1403I SNMP Initialization Error: parm.2

Explanation    Initialization of ISM SNMP management failed because the configuration record was not found on the VSAM data base.

Recommended Action    Use ISMSETUP to verify the SNMP management setup.

Error Message    NSP1405I SNMP Timeout Occurred: parm.2

Explanation    An SNMP request timed out.

Recommended Action    Verify that the device is active and responding to SNMP queries.

Error Message    NSP1406I SNMP returned error code: parm.2

Explanation    An SNMP request generated an unexpected error. The error message is displayed.

Recommended Action    Verify that the device is active and responding to SNMP queries.

Error Message    NSP1407I SNMP Address= parm.2 Text= parm.3

Explanation    The SNMP resource at the address displayed generated the displayed trap.

Recommended Action    None.

Error Message    NSP1406I SNMP recovery: parm.2

Explanation    ISM detected that all functions needed for SNMP monitoring were not available. It has attempted to recover.

Recommended Action    None.

Error Message    NSP1504I Resource parm.2 has been reset by parm.3

Explanation    Operator parm.3 entered option 6 from the CFM/390 Resource Status with Options menu. This resets the status of parm.2 and then does a status check.parm.3 is the resource index number.

Recommended Action    None, this is a audit message.

Error Message    NSP1505I Connection Count unchanged for parm.2 (parm.3).

Explanation    This is a warning that there has not been a change in the number of connections since the last check.parm.2 is the resource IP_Address. parm.3 is the resource index number.

Recommended Action    Select option 4 from the Options menu to view the latest statistics. This alert can be turned of from the CFM/390 Resource Administration menu.

Error Message    NSP1507I CPU usage threshold exceeded for parm.2 (parm.3).

Explanation    The CPU usage on parm.2 has exceeded the threshold. The router status has been updated to PERF.

Recommended Action    Press PF5 from the "Resource Status with Options" screen to diagnose the performance problem. Investigate why the CPU utilization is high.

Error Message    NSP1508I MEMORY usage threshold exceeded for parm2 (parm.3).

Explanation    The memory usage on parm.2 has exceeded the threshold. The router status has been updated to PERF.

Recommended Action    Press PF5 from the "Resource Status with Options" screen to diagnose the performance problem. Investigate why the memory utilization is high.

Error Message    NSP1512I Sysuptime error(parm.2 ).

Explanation    The system uptime on the resource is less than the previous time the resource was checked. The likely cause is that the device has been restarted.

Recommended Action    None.

Error Message    NSP1507I CPU usage threshold exceeded for parm.2 (parm.3) Resolved.

Explanation    The CPU usage on parm.2 had exceeded the threshold. The CPU utilization is now below the threshold.

Recommended Action    None.

Error Message    NSP1570I Free of DDNAME parm.2 failed with return code parm.3.

Explanation    The attempt to dynamically free the indicated DDNAME set failed. The DDNAME is freed before being reallocated. The return code is displayed.

Recommended Action    Investigate the return code in the IBM documentation.

Error Message    NSP1571I Allocate of DDNAME parm.2 to dataset parm.3 failed with return code parm.4

Explanation    The attempt to dynamically allocated the indicated data set failed. The return code is displayed.

Recommended Action    Investigate the return code in the IBM documentation.

Error Message    NSP1572I Free of DDNAME parm.2, failed. Not allocated.

Explanation    The attempt to dynamically free the indicated DDNAME failed because it was not allocated. The DDNAME is freed before being reallocated. This is not an error.

Recommended Action    None.

Error Message    NSP1573I Stop of task parm.2 failed. Messages:

Explanation    The attempt to stop the VSAM task failed. The task is stopped to to allow reallocation of the VSAM data set. The messages issued by the STOP TASK= command follow with message NSP1574I

Recommended Action    Investigate why the stop task failed. Consult the IBM NetView documentation for the messages.

Error Message    NSP1574I -parmlist

Explanation    These are the messages issued by NetView in response to the STOP TASK= command.

Recommended Action    See NSP1573I.

Error Message    NSP1575I Start of task parm.2 failed. Messages:

Explanation    The attempt to start the VSAM task failed. The task is stopped to to allow reallocation of the VSAM data set. The messages issued by the START TASK= command follow with message NSP15764I.

Recommended Action    Investigate why the start task failed. Consult the IBM NetView documentation for the messages.

Error Message    NSP1576I -parmlist

Explanation    These are the messages issued by NetView in response to the START TASK= command.

Recommended Action    See NSP1575I.

Error Message    NSP1580I - parm.2 - parm.3 reliability parm.4 less than parm.5/255 parm.6 parm.7

Explanation    The reliability of interface parm.2 on parm.1 was less than the threshold, parm.5. The reliability was parm.3/255. parm.6 and parm.7 are the date and time.

Recommended Action    Investigate why the reliability of the interface is less the threshold.

Error Message    NSP1581I - parm.2 - Command parm.3 gave an unexpected response: response

Explanation    The command parm.3 was sent to the router, parm.2 The response, response, was not what was expected.

Recommended Action    Investigate the response from the router. It likely indicates a problem on the router.

Error Message    NSP1900I parm.2 parm.3

Explanation    This message is written when the NSPDS command processor has completed an operation. The message parm.2 is the key and parm.3 is the action taken. If the command was a list, then the message contains the data record.

Recommended Action    None.

Error Message    NSP1901I END OF LISTING

Explanation    This message is written when the NSPDS command processor completes a list operation. The message is written when all the data records are processed.

Recommended Action    None.

Error Message    NSP1910I REQUEST HAS BEEN QUEUED

Explanation    This message is written when the NSPDS command processor receives a command.

Recommended Action    None.

Error Message    NSP1912E MAX NUMBER OF PARAMETERS REQUIRED

Explanation    This message is written when the NSPDS command processor detects an input command error. In this case the number of input parameters is too high.

Recommended Action    None.

Error Message    NSP1998I Invalid service type for NSPMBLD. parms

Explanation    This message indicates an error in the calling routine and that the type of service was not an L, V, B, or R.

Recommended Action    Check the routine that called NSPMBLD, and contact your system programmer.

Error Message    NSP1999I Message not found in the table. parms

Explanation    This message is created by routine NSPMBLD when it receives a message to process not found in the message table in NSPMBLD. This message should not occur.

Recommended Action    Contact your system programmer.

Error Message    NSP2015I puname netid session_data

Explanation    This message is created when the VTAM exit ISTEXCCS is executed. The data in the message string is parsed and archived by ISM.

Recommended Action    Type the NSPSDIS3 PU name to view archived data.

Error Message    NSP2091E ISM LICENSE KEY WAS NOT SPECIFIED

Explanation    This message is issued when NSPSEVDT is unable to read or parse the DSIPARM(ISMLICSE) member.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:

ISMLICENSE=LicenseKey Error Message    NSP2092E LENGTH OF LICENSE KEY MUST BE 40 BYTES

Explanation    This message is issued when NSPSEVDT has read and parsed the DSIPARM(ISMLICSE) member but found that the license key is not of the correct length.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member contains a valid license specifier in the form:

ISMLICENSE=LicenseKey

and that LicenseKey is 40 bytes long.

Error Message    NSP2093E ISM IS RUNNING ON AN UNLICENSED CPU.

Explanation    This message is issued when NSPSEVDT has read and parsed the DSIPARM(ISMLICSE) member but found that the license key does not allow ISM to execute on the current CPU.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member contains a valid license specifier in the form:

ISMLICENSE=LicenseKey Error Message    NSP2094E DSIDKS TYPE=CONN FAILED FOR DSIPARM.

Explanation    This message is issued when NSPSEVDT is unable to read the DSIPARM(ISMLICSE) member.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:

ISMLICENSE=LicenseKey Error Message    NSP2095E UNABLE TO LOCATE DSIPARM(ISMLICSE).

Explanation    This message is issued when NSPSEVDT is unable to read the DSIPARM(ISMLICSE) member.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:

ISMLICENSE=LicenseKey Error Message    NSP2096E READ FAILED FOR DSIPARM(ISMLICSE).

Explanation    This message is issued when NSPSEVDT is unable to read the DSIPARM(ISMLICSE) member.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:

ISMLICENSE=LicenseKey Error Message    NSP2097E YOUR ISM LICENSE WILL EXPIRE. DAYS LEFT: &days

Explanation    This message is issued when the license key specified in the DSIPARM(ISMLICSE) member indicates that there are fewer than 30 days left on this license. ISM continues to operate until the license key expires.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:

ISMLICENSE=LicenseKey Error Message    NSP2099E NO LICENSE FOUND FOR ISM.

Explanation    This message is issued when a module in ISM is unable to determine the current licensing environment. ISM ceases to function.

Recommended Action    Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:

ISMLICENSE=LicenseKey

Then issue the NSPSEVDT command to reset the license.


hometocprevnextglossaryfeedbacksearchhelp

Posted: Wed Oct 13 00:37:24 PDT 2004
All contents are Copyright © 1992--2004 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.