About this Guide

This section explains the objectives, intended audience, and organization of this publication and describes the conventions that convey instructions and other information.

Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.

Revision History

Document Objectives

This guide provides procedures for installation, turn up, provisioning, and acceptance of ONS 15454 nodes and ONS 15454 networks.

Audience

To use this publication, you should be familiar with Cisco or equivalent optical transmission hardware and cabling, telecommunications hardware and cabling, electronic circuitry and wiring practices, and preferably have experience as a telecommunications technician.

Document Organization

The organization of the guide reflects Cisco's recommended work flow for new installations. This organization also provides easy access to procedures and tasks used to modify existing installations. Verification procedures are provided, where necessary, to allow contract vendors to complete the physical installation and then turn over the site to craft personnel for verification, provisioning, turn up, and acceptance.

The information in the book follows a task-oriented hierarchy using the elements described below.

Chapter (Director Level)

Date	Notes
03/19/2007	Added this Revision History Table.
03/27/2007	Changed fuse rating specification for NTP-A6 in the "Install the Shelf and Backplane Cable" chapter. Added a step to DLP-D121 to enable IPPM, and clarified Manual Restart definition in ALS Mode.
05/03/2007	Added link to NTP-A326 task from NTP-A264 and NTP-A265 tasks in the "Create Circuits and VT Tunnels" chapter. Added a new procedure, NTP-A354, to the "Change Card Settings" chapter for mixed grooming mode. Added a caution relating to the fan tray and filter installation for NTP-A7 in the "Install the Shelf and Backplane Cable" chapter.
06/21/2007	Updated About this Guide chapter.
09/17/2007	Added a note after the steps in section "DLP-A255 Cross-Connect Card Side Switch Test" in the "DLPs A200 to A299" Chapter 19.
10/10/2007	Updated the Caution in the section "D255 Cross-Connect Card Side Switch Test" in the "DLPs A200 to A299" chapter.
10/16/2007	Added a note in the section "Before you Begin" in the "Upgrade Cards and Spans" chapter.
10/17/2007	Added a note after the steps in the section "NTP-A324 Create Protection Groups" in the "Turn up a Node" chapter.
11/08/2007	Added a Note in the sections, DLP-A69 and DLP-A73 in the DLPs A1 to A99 chapter.

The guide is divided into logical work groups (chapters) that serve as director entry into the procedures. For example, if you are arriving on site after a contractor has installed the shelf hardware, proceed to Chapter 2, "Install Cards and Fiber-Optic Cable" and begin verifying installation and installing cards. You may proceed sequentially (recommended), or locate the work you want to perform from the list of procedures on the first page of every chapter (or turn to the front matter or index).

Each NTP is a list of steps designed to accomplish a specific procedure. Follow the steps until the procedure is complete. If you need more detailed instructions, refer to the Detailed Level Procedure (DLP) specified in the procedure steps.

Note Throughout this guide, NTPs are referred to as "procedures" and DLPs are termed "tasks." Every reference to a procedure includes its NTP number, and every reference to a task includes its DLP number.

Detailed Level Procedure (DLP)

The DLP (task) supplies additional task details to support the NTP. The DLP lists numbered steps that lead you through completion of a task. Some steps require that equipment indications be checked for verification. When the proper response is not obtained, the DLP provides a trouble clearing reference.

Related Documentation

Use the Cisco ONS 15454 Procedure Guide with the following referenced publications:

•

Cisco ONS 15454 Reference Manual
Provides detailed card specifications, hardware and software feature descriptions, network topology information, and network element defaults.

•

Cisco ONS 15454 Troubleshooting Guide
Provides alarm descriptions, alarm and general troubleshooting procedures, error messages, and transient conditions.

•

Cisco ONS SONET TL1 Command Guide
Provides a full TL1 command and autonomous message set including parameters, AIDs, conditions and modifiers for the Cisco ONS 15454, ONS 15600, ONS 15310-CL, and
ONS 15310-MA systems.

•

Cisco ONS SONET TL1 Reference Guide
Provides general information, procedures, and errors for TL1 in the Cisco ONS 15454, ONS 15600, ONS 15310-CL, and ONS 15310-MA systems.

•

Cisco ONS 15454 and Cisco ONS 15454 SDH Ethernet Card Software Feature and Configuration G uide
Provides software features for all Ethernet cards and configuration information for Cisco IOS on ML-Series cards.

•

Release Notes for the Cisco ONS 15454 Release 8.0
Provides caveats, closed issues, and new feature and functionality information.

For an update on End-of-Life and End-of-Sale notices, refer to http://cisco.com/en/US/products/hw/optical/ps2006/prod_eol_notices_list.html.

Document Conventions

Convention	Application
boldface	Commands and keywords in body text.
italic	Command input that is supplied by the user.
[ ]	Keywords or arguments that appear within square brackets are optional.
{ x \| x \| x }	A choice of keywords (represented by x) appears in braces separated by vertical bars. The user must select one.
Ctrl	The control key. For example, where Ctrl + D is written, hold down the Control key while pressing the D key.
`screen font`	Examples of information displayed on the screen.
boldface screen font	Examples of information that the user must enter.
< >	Command parameters that must be replaced by module-specific codes.

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.


Warning	IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS
Waarschuwing	BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES
Varoitus	T�RKEIT� TURVALLISUUSOHJEITA T�m� varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin k�sittelet laitteistoa, huomioi s�hk�piirien k�sittelemiseen liittyv�t riskit ja tutustu onnettomuuksien yleisiin ehk�isytapoihin. Turvallisuusvaroitusten k��nn�kset l�ytyv�t laitteen mukana toimitettujen k��nnettyjen turvallisuusvaroitusten joukosta varoitusten lopussa n�kyvien lausuntonumeroiden avulla. S�ILYT� N�M� OHJEET
Attention	IMPORTANTES INFORMATIONS DE S�CURIT� Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entra�ner des blessures ou des dommages corporels. Avant de travailler sur un �quipement, soyez conscient des dangers li�s aux circuits �lectriques et familiarisez-vous avec les proc�dures couramment utilis�es pour �viter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de s�curit� traduites qui accompagnent cet appareil, r�f�rez-vous au num�ro de l'instruction situ� � la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS
Warnung	WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen f�hren kann. Machen Sie sich vor der Arbeit mit Ger�ten mit den Gefahren elektrischer Schaltungen und den �blichen Verfahren zur Vorbeugung vor Unf�llen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen �bersetzung in den �bersetzten Sicherheitshinweisen, die zusammen mit diesem Ger�t ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza	IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI
Advarsel	VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan f�re til skade p� person. F�r du begynner � arbeide med noe av utstyret, m� du v�re oppmerksom p� farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for � forhindre ulykker. Bruk nummeret i slutten av hver advarsel for � finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE P� DISSE INSTRUKSJONENE
Aviso	INSTRU��ES IMPORTANTES DE SEGURAN�A Este s�mbolo de aviso significa perigo. Voc� est� em uma situa��o que poder� ser causadora de les�es corporais. Antes de iniciar a utiliza��o de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos el�tricos e familiarize-se com as pr�ticas habituais de preven��o de acidentes. Utilize o n�mero da instru��o fornecido ao final de cada aviso para localizar sua tradu��o nos avisos de seguran�a traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRU��ES
�Advertencia!	INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este s�mbolo de aviso indica peligro. Existe riesgo para su integridad f�sica. Antes de manipular cualquier equipo, considere los riesgos de la corriente el�ctrica y familiar�cese con los procedimientos est�ndar de prevenci�n de accidentes. Al final de cada advertencia encontrar� el n�mero que le ayudar� a encontrar el texto traducido en el apartado de traducciones que acompa�a a este dispositivo. GUARDE ESTAS INSTRUCCIONES
Varning!	VIKTIGA S�KERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utf�r arbete p� n�gon utrustning m�ste du vara medveten om farorna med elkretsar och k�nna till vanliga f�rfaranden f�r att f�rebygga olyckor. Anv�nd det nummer som finns i slutet av varje varning f�r att hitta dess �vers�ttning i de �versatta s�kerhetsvarningar som medf�ljer denna anordning. SPARA DESSA ANVISNINGAR





Aviso	INSTRU��ES IMPORTANTES DE SEGURAN�A Este s�mbolo de aviso significa perigo. Voc� se encontra em uma situa��o em que h� risco de les�es corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos el�tricos e familiarize-se com as pr�ticas padr�o de preven��o de acidentes. Use o n�mero da declara��o fornecido ao final de cada aviso para localizar sua tradu��o nos avisos de seguran�a traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRU��ES
Advarsel	VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. F�r du begynder arbejde p� udstyr, skal du v�re opm�rksom p� de involverede risici, der er ved elektriske kredsl�b, og du skal s�tte dig ind i standardprocedurer til undg�else af ulykker. Brug erkl�ringsnummeret efter hver advarsel for at finde overs�ttelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER

Obtaining Optical Networking Information

This section contains information that is specific to optical networking products. For information that pertains to all of Cisco, refer to the Obtaining Documentation, Obtaining Support, and Security Guideliens section.

Where to Find Safety and Warning Information

For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15454 system. It also includes translations of the safety warnings that appear in the ONS 15454 system documentation.

Cisco Optical Networking Product Documentation CD-ROM

Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.

Obtaining Documentation, Obtaining Support, and Security Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

Table Of Contents