|
|
Table Of Contents
INIT Commands
This chapter provides INIT (initialize) commands for the Cisco ONS 15454, ONS 15327, ONS 15600 and ONS 15310-CL.
15.1 INIT-REG-<MOD2>
Initialize Register (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS1, DV6000, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, VT2)
See Table 27-1 for supported modifiers by platform.
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command initializes the performance monitoring (PM) registers.
Note
•
•
•
CategoryPerformance
SecurityMaintenance
Related Commands
Input FormatINIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<LOCN>],[<DIRN>],[<TMPER>]
[,,];Input ExamplesINIT-REG-OC3:CISCO:FAC-1-1:1234::CVL,,NEND,BTH,15-MIN;
Input Parameters
Table 15-1 INIT-REG-<MOD2> Input Parameters
AID
Access identifier from the "ALL" section. All of the STS, VT1, Facility and DS1 AIDS are supported
MONTYPE
Monitored type
Parameter type is ALL_MONTYPE—monitoring type list
•
Alarm Indication Signal Seconds—Path
•
All possible values
•
OTN—Background Block Errors—Path Monitor Point
•
OTN—Background Block Errors—Section Monitor Point
•
OTN—Background Block Error Ratio—Path Monitor Point expressed as 1/10th of a percentage.
•
OTN—Background Block Error Ratio—Section Monitor Point expressed as 1/10th of a percentage.
•
FEC—Bit Errors Corrected
•
8B10B—Code Group Violations
•
Controlled Slip Seconds—Path (DSXM-12 FDL/T1.403 PM count)
•
Coding Violations—CP-Bit Path
•
Coding Violations—Line
•
Coding Violations—Path
•
Coding Violations—Section
•
Coding Violations—Section
•
8B10B—Data Code Groups
•
Errored Second Type A-Path (DS3XM-12 DS1 PM count)
•
Errored Second Type B-Path (DS3XM-12 DS1 PM count)
•
Errored Seconds—CP—Bit Path
•
Errored Seconds—Line
•
Errored Second -Network Path (DS3XM-12 DS1 PM count)
•
Errored Seconds—Path
•
OTN—Errored Seconds—Path Monitor Point
•
OTN—Errored Seconds—Section Monitor Point
•
Errored Second—Ratio
•
Errored Seconds Ratio—Path monitor Point expressed as 1/10th of a percentage
•
Errored Seconds Ratio—Section monitor Point expressed as 1/10th of a percentage
•
Errored Seconds—Section
•
Errored Seconds—VT Path
•
The total number of good packets received that were directed to a multicast address
•
Number of transmit packets that are collisions
•
The total number of packets received that have a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets
•
Number of received frames dropped at the port level
•
The total number of packets received that were less than 64 octets
•
The total number of packets received that are longer than 1518 octets
•
The total number of octets of data
•
The total number of packets received that are longer than 1518 octets
•
The total number of packets (including bad packets, broadcast packets, and multicast packets) received
•
The total number of packets received that are less than 64 octets
•
Failure Count—Line
•
OTN—Failure Count—Path Monitor Point
•
OTN—Failure Count—Section Monitor Point
•
Availability Ratio
•
High-Order Path Background Block Error
•
High-Order Path Background Block Error Ratio
•
High-Order Path Errored Block
•
High-Order Path Errored Second
•
High-Order Path Errored Seconds - A
•
High-Order Path Errored Seconds - B
•
High-Order Path Errored Second Ratio
•
High-Order Path Failure Count
•
High Order Path Negative Pointer Justification Count
•
High Order Path, Negative Pointer Justification Count
•
Outage Intensity
•
High Order Path Pointer Justification Count Difference
•
High Order Path Pointer Justification Count
•
High Order Path Pointer Justification Count Seconds
•
High Order Path Positive Pointer Justification Count
•
High Order Path, Positive Pointer Justification Count
•
The number of SEP events in available time
•
High-Order Path Severely Errored Seconds
•
High-Order Path Severely Errored Second Ratio
•
High-Order Path Unavailable Seconds
•
Number of broadcast packets received since the last counter reset
•
The number of inbound packets
•
Receive Error Byte
•
The number of inbound packets (or transmission units) that contained errors
•
Receive Framing Error
•
Receive Interpkt Junk
•
Number of multicast packets received since the last counter reset
•
Number of bytes transmitted since the last counter reset
•
Number of unicast packets received since the last counter reset
•
Number of broadcast packets transmitted
•
The number of outbound packets
•
The number of outbound packets (or transmission units) that could not be transmitted because of errors
•
Number of multicast packets transmitted
•
Received payload CRC errors
•
Number of unicast packets transmitted
•
8B10B- Idle Ordered Sets
•
Invalid Packet Count
•
Average Laser Bias current in uA
•
Maximum Laser Bias current in uA
•
Minimum Laser Bias current in uA
•
Normalized Laser Bias Current for OC3-8
•
Laser Bias Current
•
Laser Bias Current
•
Loss of Signal Seconds—Line
•
Low-Order Path Background Block Error
•
Low-Order Path Background Block Error Ratio
•
Low-Order Path Errored Block
•
Low-Order Path Errored Second
•
Low-Order Path Errored Seconds-A
•
Low-Order Path Errored Seconds-B
•
Low-Order Path Errored Second Ratio
•
Low-Order Path Failure Count
•
Low-Order Negative Pointer Justification Count, Detected
•
Low Order Negative Pointer Justification Count, Generated
•
Low-Order Positive Pointer Justification Count, Detected
•
Low-Order positive Pointer Justification Count, Generated
•
Low-Order Path Severely Errored Period
•
Low-Order Path Severely Errored Period Intensity
•
Low-Order Path Severely Errored
•
Low-Order Path Unavailable Seconds
•
Protection switch count
•
Protection switch duration
•
8B10B—Non Idle Ordered Sets
•
PPJC-PDET:Negative Pointer Justification
•
PPJC-PGEN:Negative Pointer Justification
•
Average Receive Power in 1/10 uW
•
Maximum Receive Power in 1/10 uW
•
Minimum Receive Power in 1/10 uW
•
Normalized Optical Receive Power for OC3-8
•
Maximum value for OPRN
•
Minimum value for OPRN
•
Average Transmit Power in 1/10 uW
•
Maximum Transmit Power in 1/10 uW
•
Minimum Transmit Power in 1/10uW
•
Normalized value for Optical Power Transmitted for the OC3-8 card
•
Maximum value for OPTN
•
Minimum value for OPTN
•
Optical Power—Average Interval Value in 1/10th of dBm
•
Optical Power—Maximum Interval Value in 1/10th of dBm
•
Optical Power—Minimum Interval Value in 1/10th of dBm
•
PPJC-PDET:Positive Pointer Justification
•
PPJC-PGEN:Positive Pointer Justification
•
Protection Switching Count
•
Protection Switching Count—Ring
•
Protection Switching Count—Span
•
Protection Switching Count—Working
•
Protection Switching Duration
•
Protection Switching Duration—Ring
•
Protection Switching Duration—Span
•
Protection Switching Duration—Working
•
Severely Errored Framing/AIS Second—CP-Bit Path
•
Severely Errored Framing/AIS Seconds Path
•
Severely Errored Framing Seconds
•
Severely Errored Framing Seconds—Path (DS3XM-12 DS1 PM count)
•
Severely Errored Second—CP-Bit Path
•
Severely Errored Second—Line
•
Severely Errored Second - Network Path (DS3XM-12 DS1 PM count)
•
Severely Errored Second—Path
•
OTN—Severely Errored Second—Path
•
OTN—Severely Errored Second Ratio—Path Monitor Point expressed as 1/10th of a percentage
•
OTN—Severely Errored Second Ratio—Section Monitor Point expressed as 1/10th of a percentage
•
Severely Errored Second—Section
•
OTN—Severely Errored Second—Section Monitor Point
•
Severely Errored Second—VT Path
•
Unavailable Second—CP-Bit Path
•
Unavailable Second—Line
•
Unavailable Second - Network Path (DS3XM-12 DS1 PM count)
•
Unavailable Second—Path
•
OTN—Unavailable Second—Path Monitor Point
•
OTN—Unavailable Second—Section Monitor Point
•
Unavailable Second—VT Path
•
FEC—Uncorrectable Words
•
Valid Packet Count
LOCN
Location associated with a particular command in reference to the entity identified by the AID
Parameter type is LOCATION—the location where the action is to take place
•
Action occurs on the Far End of the facility
•
Action occurs on the Near End of the facility
DIRN
Direction relative to the entity identified by the AID. Defaults to ALL which means that the command initializes all of the registers irrespective of the PM direction
Parameter type is DIRECTION—transmit and receive directions
•
Both transmit and receive directions
•
Receive direction only
•
Transmit direction only
TMPER
Accumulation time period for performance counters. A null value defaults to 15-MIN. Defaults to 15-MIN
Parameter type is TMPER—accumulation time period for the performance management center
•
Performance parameter accumulation interval length; every 24-hours. For SONET PM data only one day of history data is available. For RMON managed PM data seven days of history data are available.
•
Performance parameter accumulation interval length; every 1 hour. This is only applicable to RMON managed PM data. There are 24 hours of history data available.
•
Performance parameter accumulation interval length; every 1 minute. This is only applicable to RMON managed PM data. There are 60 minutes of history available.
•
Performance parameter accumulation interval length; every 15 minutes. There are 32 15-MIN buckets of history data available for this accumulation interval length.
•
Performance parameter accumulation interval length; starting from the last time the counters were cleared. This is only applicable to RMON managed PMs.
15.2 INIT-SYS
Initialize System
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command initializes the specified card and its associated subsystems.
Note
•
•
•
•
•
CategorySystem
SecurityMaintenance
Related Commands
Input FormatINIT-SYS:[<TID>]:<AID>:<CTAG>::<PH>[,<CMDMODE>];
Input ExamplesINIT-SYS:HOTWATER:SLOT-8:201::1,FRCD;
Input Parameters
Table 15-2 INIT-SYS Input Parameters
AID
Access identifier from the "EQPT" section
PH
The phase. 1=soft reset; 2=hard reset. PH is a required parameter for the ONS 15600 and ONS 15310-CL. PH is not supported on the ONS 15327. PH is supported on the CE-100T-8 on the ONS 15454. Integer
CMDMDE
Command Mode. Allows the user to override safety checks. CMDMDE is optional for the ONS 15600 and defaults to NORM. CMDMDE is not supported on the ONS 15454, ONS 15327, ONS 15310-CL
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands, but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that could make the command fail
Posted: Mon Sep 3 11:18:54 PDT 2007
All contents are Copyright © 1992--2007 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
