|
|
Table Of Contents
6.2 Alarm Interface, FAN-ALARM
6.2.3 Electrical Parameters Alarm Input
6.2.4 Electrical Parameters Alarm Output
Physical Interfaces
6.1 Power module, DC Power
See the "2.4 Power Module, DC Power" section on page 2-6.
6.2 Alarm Interface, FAN-ALARM
6.2.1 Description
The ONS15305 provides facilities to report a minimum of 4 auxiliary alarm inputs for associated equipment, e.g. power unit failure battery condition, cabinet door etc. and 2 dedicated alarm outputs. The alarm outputs are related to the unit alarm indicator and the traffic alarm indicator. The input alarms are reported to the management system and are activated by a closed or open loop condition between a pair of contacts.
Figure 6-1 Alarm Input and Output Overview
6.2.2 Connectors
The alarm interface connector is a 9 pin DSUB type connector, with the following pin-out:
6.2.3 Electrical Parameters Alarm Input
6.2.4 Electrical Parameters Alarm Output
6.3 Auxiliary Interface
6.3.1 Description
The ONS15305 offers a proprietary Auxiliary interface for termination of overhead bytes selected from the different STM-N interfaces. The Auxiliary interface is located on the System controller module, SYSCONT-SD128-RJ45.
Each STM-N interface can be configured to terminate one of the following overhead bytes: E1,F1 or E2. The byte to be terminated is selected from the network management system together with a unique timeslot number n, where n equals 1-15 or 17-31. The Auxiliary interface is a framed E1 interface, according to ITU-T G.704, where timeslot 1-15 and 17-31 can carry one overhead byte each, according to the configuration described above.
The interface is synchronous which means that the incoming STM-N need to be synchronized with the T0 reference clock in the ONS15305 and the incoming framed E1 need to be synchronized with the outgoing framed E1. Bit slips will occur if one of the interfaces are free running.
6.3.2 Connector
The connector is a RJ-45 connector, with the following pin-out:
Table 6-4 Pin Out Auxiliary Interface
1
AUX_DO+
2
AUX_DO-
3
GND
4
AUX_DI+
5
AUX_DI-
6
AUX_SHIELD
7
NC
8
NC
Note
Pin 6 is always AC connected to ground
The outer screen is always direct connected to ground.
6.4 VT-100 Terminal Interface
6.4.1 Description
The ONS15305 offers a VT-100 interface for connection of a CiscoEdgeCraft Terminal/CLI interface. The interface is running at a data rate of 19.200 baud and is located on the System controller module, SYSCONT-SD128-RJ45.
The interface is in accordance with the specifications given in the Compliance chapter below.
6.4.2 Connector
The RS232 interface for ONS15305 is provided through a RJ-45 connector, with the following pin-out:
Table 6-5 Pin-out VT-100 Connector
1
GND
2
TxD
3
RxD
4
DB-TxD
5
GND
6
VT_CTS
7
DB_RxD
8
VT_RTS
Note
6.5 Synchronization Interface
6.5.1 Description
The interface is a 120 ohm 2048 kHz synchronization input and output port, with specifications according to ITU-T G.703, and is located on the System controller module, SYSCONT-SD128-RJ45.
6.5.2 Connectors
Both input and output is provided on 8 pin RJ-45 connector, with the following pin-out:
Table 6-6 Pin Out Synchronization Port
1
SYNC_OUT+
2
SYNC_OUT-
3
GND
4
SYNC_IN+
5
SYNC_IN-
6
SYNC_SCREEN
7
NC
8
NC
Note
6.5.3 Other Interfaces
Other interface descriptions are found in the chapters describing each service module.
6.5.4 Prot Interface
For future release.
Posted: Fri Sep 14 10:37:02 PDT 2007
All contents are Copyright © 1992--2007 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
