|
Table Of Contents
Release Notes for the Cisco ONS 15216 OADM Release 2.2
Obtaining Technical Assistance
Release Notes for the Cisco ONS 15216 OADM Release 2.2
November, 2002
Release notes address closed (maintenance) issues, caveats, and new features for the Cisco ONS 15216 Optical Add/Drop Multiplexer (OADM). For detailed information regarding features, capabilities, hardware, and software introduced with this release, refer to Cisco ONS 15216 100 GHz OADM Operations Guide, Release 2.2
Cisco also provides Bug Toolkit, a web resource for tracking defects. To access Bug Toolkit, visit the following URL:
http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl
Contents
Caveats
Review the notes listed below before deploying the ONS 15216. Caveats with DDTS tracking numbers are known system limitations that are scheduled to be addressed in a subsequent release. Caveats without DDTS tracking numbers are provided to point out procedural or situational considerations when deploying the product.
Hardware Caveats
There are no hardware caveats for this release.
Software Caveats
The following software caveats exist in Release 2.2.
CSCdx57061: Telnet port 3083 does not require a semicolon after TL1 commands
TL1 commands are sent on the 3083 telnet port when the user hits the enter key - no semicolon is required.
Conditions
This behavior limited to port 3083. Port 3082 correctly requires that a semicolon be used to terminate and send a TL1 command.
Workaround
Commands are correctly sent if the semicolon key is used to terminate the command line.
CSCdx78978: ED-, RTRV-, SET-TH, and RTRV-TH-DWDM take more than two seconds to complete
TL1 commands ED-DWDM, RTRV-DWDM, SET-TH-DWDM, and RTRV-TH-DWDM may sometimes take three to four seconds to complete, without issuing an "in progress" message.
Conditions
Occurs intermittently.
Workaround
None.
CSCdy63785: Incorrect syntax for RTRV-AO command response
A carriage return and line feed (i.e. a blank line) is missing from RTRV-AO response message, prior to the final " */" before the terminating semicolon.
Conditions
Occurs under all conditions.
Workaround
None. Issue will be resolved in a future software release.
CSCdy63840: RTRV-STATUS command should be allowed to any user
Only RWA level users have access to the RTRV-STATUS command.
Conditions
Occurs under all conditions.
Workaround
Log in as a RWA level user to execute the RTRV-STATUS command.
CSCdy65043: INH/ALW-MSG-ALL commands should be allowed to any user.
Only RWA and RW level users have access to the INH-MSG-ALL and ALW-MSG-ALL commands.
Conditions
Occurs under all conditions.
Workaround
Log in as a RWA or RW level user to execute the INH-MSG-ALL or ALW-MSG-ALL commands.
CSCdy67601: MSGTYPE filter only works if ATAGSEQ is specified
When issuing the RTRV-AO command, MSGTYPE filter (to screen for ALM or EVT messages) does not work unless specific boundaries are issued regarding the desired message range.
Conditions
Occurs under all conditions.
Workaround
None. Issue will be resolved in a future software release.
CSCdy67627: Incorrect filtering implementation for RTRV-ALM-DWDM and RTRV-ALM-COM
The specific parameters used in the stage General Blockof the RTRV-ALM-DWDM and RTRV-ALM-COM commands are used as an OR condition instead of an AND condition. For example, after entering RTRV-ALM-DWDM:::123::MN,LOSADD; the response will show alarms of type LOSADD or with severity MN (instead of only those of type LOSADD and with severity MN).
Conditions
Occurs only when more than one parameter is specified in the stage general block.
Workaround
None. Issue will be resolved in a future software release.
CSCdy67682: ED-DAT command should be allowed to any user
Only RWA and RW level users have access to the ED-DAT command.
Conditions
Occurs under all conditions.
Workaround
Log in as a RWA or RW level user to execute the ED-DAT command.
CSCdy80557: RTRV-DFLT-SECU response message does not display the <aid>
The response message for the RTRV-DFLT-SECU does not include the EQPT <aid>, as per TR-835.
Conditions
Occurs for the RTRV-DFLT-SECU command.
Workaround
None. Issue will be resolved in a future software release.
CSCdz40833: LOSDROP East-1 alarm enable/disable status is always enabled after a reset
On the 1-ch OADM, the EAST-1 drop port LOS alarm can be disabled, but after a restart of the unit the alarm is displayed again as enabled.
Conditions
Occurs only on the 1-ch OADM EAST-1 drop port when there is a software reset.
Workaround
If the alarm needs to be disabled, use the ED-NE-GEN command again after a reset to disable the alarm.
CSCdz40902: Timeout setting is not kept after a restart
The timeout setting is not stored in the non-volatile memory, so if the user changes the timeout value, the new setting is kept if he logs out and then log in again, but is not kept after a restart of the unit (INIT-SYS). After the restart, the values of the timeout are reverted back to the default values (e.g. 15 minutes for RWA users).
Conditions
Occurs for the SET-ATTR-SECUDFLT command if there is a software restart.
Workaround
If the timeout settings are changed from their default values, use the SET-ATTR-SECUDFLT command again after a restart to set the timeout values.
CSCdz41689: Date setting unsuccessful if power cycle happens before user logs out
The date/time settings do not take effect if a power cycle happens before the user logs out. Notice that a soft reset (through INIT-SYS) does not have the same impact (after the reset the date and time setting are still kept).
Conditions
Occurs for the ED-DAT command if the unit is power cycled before user log out.
Workaround
If the date or time is edited, the user should log out before power cycling the unit.
CSCdz41745: Alarms/events log file is reset (emptied) after soft or hard reset
The log files of the autonomous messages are not retained if a power cycle or a soft reset (through INIT-SYS) is performed.
Conditions
Occurs if the unit is reset or power cycled.
Workaround
Retrieve the autonomous message log using the RTRV-AO command before resetting or power cycling the unit.
New Features
This section provides a description of the new features found in ONS 15216, Release 2.2.
New Hardware Features
This section is a high-level overview of the hardware features of ONS 15216, Release 2.2.
One channel OADM
A one channel OADM is now part of the ONS 15216 product line.
Increased EVOA accuracy
Improved EVOA accuracy is now 1.04 dB.
New Software Features
This section is a high-level overview of the software features of ONS 15216—Network Release 2.2.
Dual DC voltage monitoring
The ONS 15216 OADM now has the capability to individually monitor and alarm the A and B DC voltage feeds.
CALCSETP function
The addition of the CALCSETP parameter as part of the response to the RTRV-DWDM command provides the user with the ONS 15216's recommended add channel optical power setting based on the optical power of the corresponding drop channel.
Obtaining Documentation
These sections explain how to obtain documentation from Cisco Systems.
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at this URL:
Translated documentation is available at this URL:
http://www.cisco.com/public/countries_languages.shtml
Documentation CD-ROM
Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which is shipped with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual subscription.
Ordering Documentation
You can order Cisco documentation in these ways:
•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace:
http://www.cisco.com/cgi-bin/order/order_root.pl
•Registered Cisco.com users can order the Documentation CD-ROM through the online Subscription Store:
http://www.cisco.com/go/subscription
•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, U.S.A.) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).
Documentation Feedback
You can submit comments electronically on Cisco.com. In the Cisco Documentation home page, click the Fax or Email option in the "Leave Feedback" section at the bottom of the page.
You can e-mail your comments to bug-doc@cisco.com.
You can submit your comments by mail by using the response card behind the front cover of your document or by writing to the following address:
Cisco Systems
Attn: Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883We appreciate your comments.
Obtaining Technical Assistance
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from online tools by using the Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC Web Site.
Cisco.com
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.
Cisco.com is a highly integrated Internet application and a powerful, easy-to-use tool that provides a broad range of features and services to help you with these tasks:
•Streamline business processes and improve productivity
•Resolve technical issues with online support
•Download and test software packages
•Order Cisco learning materials and merchandise
•Register for online skill assessment, training, and certification programs
If you want to obtain customized information and service, you can self-register on Cisco.com. To access Cisco.com, go to this URL:
Technical Assistance Center
The Cisco Technical Assistance Center (TAC) is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two levels of support are available: the Cisco TAC Web Site and the Cisco TAC Escalation Center.
Cisco TAC inquiries are categorized according to the urgency of the issue:
•Priority level 4 (P4)—You need information or assistance concerning Cisco product capabilities, product installation, or basic product configuration.
•Priority level 3 (P3)—Your network performance is degraded. Network functionality is noticeably impaired, but most business operations continue.
•Priority level 2 (P2)—Your production network is severely degraded, affecting significant aspects of business operations. No workaround is available.
•Priority level 1 (P1)—Your production network is down, and a critical impact to business operations will occur if service is not restored quickly. No workaround is available.
The Cisco TAC resource that you choose is based on the priority of the problem and the conditions of service contracts, when applicable.
Cisco TAC Web Site
You can use the Cisco TAC Web Site to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC Web Site, go to this URL:
All customers, partners, and resellers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC Web Site. The Cisco TAC Web Site requires a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to this URL to register:
http://www.cisco.com/register/
If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC Web Site, you can open a case online by using the TAC Case Open tool at this URL:
http://www.cisco.com/tac/caseopen
If you have Internet access, we recommend that you open P3 and P4 cases through the Cisco TAC Web Site.
Cisco TAC Escalation Center
The Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.
To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
Before calling, please check with your network operations center to determine the level of Cisco support services to which your company is entitled: for example, SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). When you call the center, please have available your service agreement number and your product serial number.
This document is to be used in conjunction with the documents listed in the "Obtaining Documentation" section.
CCIP, the Cisco Arrow logo, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That's Possible, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, LightStream, MGX, MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0208R)Copyright © 2002, Cisco Systems, Inc.
All rights reserved.
Posted: Sun Apr 2 03:27:22 PDT 2006
All contents are Copyright © 1992--2006 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.