![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Table Of Contents
Considerations for Using Splitter Protection
Configuring Splitter Protection
Displaying the Splitter Protection Configuration
About Client Based Line Card Protection
About Y-Cable Line Card Protection
Considerations for Using Y-Cable Based Line Card Protection
Configuring Y-Cable Based Line Card Protection
Displaying the Y-Cable Protection Configuration
Configuring Splitter Protected Line Card Motherboards for Line Card Protection
About Trunk Fiber Based Protection
Considerations for Using Trunk Fiber Based Protection
Configuring Trunk Fiber Based Protection
Displaying Trunk Fiber Protection Configuration
Configuring APS Group Attributes
Configuring Revertive Switching
Configuring the Switchover-Enable Timer
Configuring the Wait-to-Restore Timer
Configuring the Search-For-Up Timer
Configuring the Message Timers
Requesting a Switchover or Lockout
Clearing Switchovers and Lockouts
Configuring APS
This chapter describes how to configure splitter protection and line card protection with APS (Automatic Protection Switching). This chapter contains the following sections:
•
Configuring Splitter Protection
•
About Client Based Line Card Protection
•
About Y-Cable Line Card Protection
•
Configuring Y-Cable Based Line Card Protection
•
About Trunk Fiber Based Protection
•
Configuring Trunk Fiber Based Protection
•
Configuring APS Group Attributes
Note
To ensure the installed Cisco IOS software supports your hardware and provides the software features you wish to use, see the "New and Changed Information" section on page xviii. Also refer to the "Hardware Supported" section and "Feature Set" section of the latest release notes for the Cisco ONS 15540 ESPx.
About APS
APS provides protection against signal transmission failure. The Cisco ONS 15540 ESPx supports the following APS features:
•
1+1 path protection
•
Splitter protection
•
Line card protection
–
Client based
–
Y-cable based
•
Trunk Fiber Based Protection
•
Bidirectional and unidirectional path switching
The 1+1 path protection architecture transmits the client signal on both the working and protection paths.
Note
For an animated description of the APS implementation on the Cisco ONS 15540 ESPx, go to the following URL:
http://www.cisco.com/mm/dyngraph/APS15540.html
About Splitter Protection
Splitter protection on the Cisco ONS 15540 ESPx provides protection against facility failure, such as trunk fiber cuts, but not transponder module failures or client equipment failures. Splitter protection internally replicates the client optical signal received from the transponder module and transmits it to mux/demux modules in both slot 0 and slot 1 (see Figure 7-1).
Figure 7-1 Splitter Protection Scheme with 2.5-Gbps Transponder Module
On the trunk side, a fiber pair, with one receive fiber and one transmit fiber, connects to one mux/demux module in slot 0. Another trunk fiber pair connects to a mux/demux module in slot 1. The client signal is transmitted through both mux/demux modules to the trunk fiber pairs. A 2 x 2 switch on the line card motherboard receives both signals from the trunk fiber pairs and selects one as the active signal. When a signal failure is detected, the 2 x 2 switch switches over to the standby signal. The standby signal then becomes the active signal.
Considerations for Using Splitter Protection
The following considerations apply when considering the use of splitter protection:
•
Each subcard position in the splitter protected line card motherboard corresponds to a specific filter interface on both of the mux/demux modules when using direct cross connections. If you are using a cross connect panel, channels can be cross connected between any subcard position on the line card motherboard and any filter interface on a mux/demux module.
For detailed information on cross connecting components, refer to the Cisco ONS 15540 ESPx Planning Guide.
•
Splitter protection does not protect against failure in the transponder module, where the lasers are located. Splitter protection also does not protect against failure of the client equipment.
To protect against transponder module failure, use y-cable protection as described in the "About Line Card Protection" section and the "Configuring Y-Cable Based Line Card Protection" section. To protect against both transponder module failure and client failure, implement protection on the client equipment instead.
•
A system fully configured with 2.5-Gbps transponders can support 32 channels in splitter protection mode.
•
A system fully configured with 10-GE transponder modules can support 16 channels in splitter protection mode.
•
Splitter protection is nonrevertive. After correcting the problem that caused the signal failure and verifying the signal quality, you must manually switch the signal over to begin using the former working path. Use optical testing equipment to verify the signal quality.
•
For interfaces with either Sysplex ETR or Sysplex CLO protocol encapsulation, configure bidirectional path switching to ensure proper functioning of the protocol.
For detailed information on shelf configuration rules, refer to the Cisco ONS 15540 ESPx Planning Guide.
Configuring Splitter Protection
The following steps describe the tasks required to configure splitter protection:
Step 1
Determine the number of clients you need to support and which channels you will deploy to transport client data.
Step 2
Ensure that the correct transponder modules are inserted in the line card motherboards in slots 2 through 5 and 8 through 11.
Step 3
Ensure that the mux/demux modules needed to support the deployed channels are inserted in the correct subcards of the mux/demux motherboards.
For each band of four or eight channels, you need two mux/demux modules that support the same channels.
For detailed information on hardware configuration rules, refer to the Cisco ONS 15540 ESPx Planning Guide.
Step 4
Ensure that the line card motherboards are correctly cross connected to the mux/demux modules and that the cabling configuration is correctly entered with the patch command on the CLI (command-line interface). For detailed information on the patch command, see the "About Patch Connections" section on page 4-20.
Ensure that the add/drop mux/demux modules are correctly interconnected with the external optical patch cables and that the cabling configuration is correctly entered with the patch command on the CLI. For detailed information on the patch command, see the "About Patch Connections" section on page 4-20.
Step 5
Configure APS from the CLI.
CautionLaser safety control interrupts signal transmission with splitter protected configurations. If you configure the system with splitter protection and enable laser safety control, the transmit laser to the client shuts down when an open fiber occurs on one transport fiber and signal transmission to the client is interrupted.
To enable splitter protection, use the following commands, beginning in global configuration mode:
Examples
This example shows how to associate all the wavepatch interfaces in the shelf for splitter protection and enable APS activity.
Switch#
configure terminalSwitch(config)# redundancy
Switch(config-red)# associate interface wavepatch */*/0 wavepatch */*/1 enable
Switch(config-red)#
This example shows how to associate all the wavepatch interfaces in slot 2 for splitter protection and enable APS activity.
Switch#
configure terminalSwitch(config)# redundancy
Switch(config-red)# associate interface wavepatch 2/*/0 wavepatch 2/*/1 enable
Switch(config-red)#
This example shows how to associate wavepatch interfaces for the transponder module in slot 3 and subcard 0 for splitter protection and modify the default attribute settings.
Switch#
configure terminalSwitch(config)# redundancy
Switch(config-red)# associate group dallas1
Switch(config-red-aps)# aps working wavepatch 3/0/0
Switch(config-red-aps)# aps protection wavepatch 3/0/1
Switch(config-red-aps)# aps enable
Displaying the Splitter Protection Configuration
To display the splitter protection configuration, use the following EXEC commands:
Example
The following example shows how to display the APS splitter protection configuration:
Switch# show aps
AR : APS Role, Wk: Working, Pr: Protection
AS : APS State, Ac: Active, St: Standby
IS : Interface State, Up: Up, Dn: Down
MPL: Minimum Protection Level, SD: Signal Degrade, SF: Signal Failure
LOL: Loss of Light, - not currently protected
Interface AR AS IS MPL Redundant Intf Group Name
~~~~~~~~~~~~~~~~~ ~~ ~~ ~~ ~~~ ~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~
Wavepatch5/3/0 Wk St Up Wavepatch5/3/1 Seattle
Wavepatch5/3/1 Pr Ac Up LOL Wavepatch5/3/0 Seattle
Switch# show aps detail
APS Group Seattle :
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end (network side splitter)
direction....: prov: uni, current: uni, remote prov: uni
revertive....: no
created......: 14 hours, 54 minutes
aps state....: associated (enabled)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
search-up int: min: 2 secs, max: 32 secs
switched chan: 1
channel ( 0): Wavepatch5/3/1 (ACTIVE - UP)
: channel request: no-request
: transmit request: do-not-revert
: receive request: no-request
channel ( 1): Wavepatch5/3/0 (STANDBY - UP)
: channel request: do-not-revert
: switchover count: 1
: last switchover: 14 hours, 54 minutes
In show aps command, Signal degrade (SD) and signal failure (SF) indicates the signal quality based on the signal data stream. Signal degrade is reported when the number of errors reported per second is more than the signal degrade threshold. Signal failure is reported when the number of errors per second is more than the signal failure threshold. For more information on configuring SD and SF, refer to "Configuring Alarm Thresholds" section for each card interface.
About Line Card Protection
Line card protection on the Cisco ONS 15540 ESPx provides protection against both facility failures and line card failures. With line card protection, a duplicated signal is transmitted over ITU channels generated on separate line cards.
The Cisco ONS 15540 ESPx supports three types of line card protection:
•
Client based protection
•
Y-cable protection
•
Switch fabric based protection
About Client Based Line Card Protection
In client protection mode, both signals are transmitted to the client system. The client system decides which signal to use and when to switch over.
Note
Client protection does not require APS configuration on the Cisco ONS 15540 ESPx.
Figure 7-2 Line Card Protection Scheme with 2.5-Gbps Transponder Module
The Cisco ONS 15540 ESPx supports two types of line card protection, client protection and y-cable protection. In client protection mode, both signals are transmitted to the client system. The client system decides which signal to use and when to switch over.
Note
Client protection does not require APS configuration on the Cisco ONS 15540 ESPx.
With y-cable protection, the signal from only one of the transparent interfaces is transmitted to the client. The Cisco ONS 15540 ESPx turns on the laser at the active transparent interface, and turns off the laser on the standby transparent interface. At each receiver on the trunk side of the transponder module, the system monitors the optical signal power level. If the system detects a failure of the active signal when an acceptable signal exists on the standby transponder module, a switchover to the standby signal occurs by turning off the active transmitter at the client interface and turning on the standby transmitter.
About Y-Cable Line Card Protection
With y-cable protection, the client equipment sends only one signal to two transponder line cards using a y-cable to replicate the signal. The client equipment receives from only one transponder line card. The Cisco ONS 15540 ESPx turns on the laser at the active transparent interface, and turns off the laser on the standby transparent interface. At each receiver on the trunk side of the transponder line card, the system monitors the optical signal power level. If the system detects a failure of the active signal when an acceptable signal exists on the standby transponder line card, a switchover to the standby signal occurs by turning off the active transmitter at the client interface and turning on the standby transmitter.
Considerations for Using Y-Cable Based Line Card Protection
The following considerations apply when considering the use of line card protection:
•
Cross connect the channels from the wavepatch interfaces on the line card motherboard to the filter interfaces on the mux/demux modules or the mux/demux motherboards. Each subcard position in an unprotected line card motherboard corresponds to a specific filter interface on a mux/demux module when using direct cross connections. If you are using a cross connect panel, channels can be cross connected between any subcard position on the line card motherboard and any filter interface on a mux/demux module.
For detailed information on cross connecting components, refer to the Cisco ONS 15540 ESPx Planning Guide.
•
Y-cable line card protection does not protect against failures of the client equipment. To protect against client failures, ensure that protection is implemented on the client equipment itself.
•
A fully provisioned single shelf of 2.5-Gbps transponder modules can support 16 channels in line card protection mode. A fully provisioned dual shelf of 2.5-Gbps transponder modules can support 32 channels in line card protection mode.
•
A fully provisioned single shelf of 10-Gbps transponder modules can support 8 channels in line card protection mode. A fully provisioned dual shelf of 10-Gbps transponder modules can support 16 channels in line card protection mode.
For more information about dual shelf nodes, see "Configuring Dual Shelf Nodes."
•
Y-cable line card protection supports revertive behavior. With revertive behavior, the signal automatically switches back to the working path after the signal failure has been corrected. The default behavior is nonrevertive.
•
To simplify system management, terminate the client signal on two transponder modules of the same channel. In this way the client signal maps to the same WDM wavelength on both the working and protection paths.
•
For interfaces with either Sysplex ETR or Sysplex CLO protocol encapsulation, configure bidirectional path switching to ensure proper functioning of the protocol.
CautionDo not configure y-cable protection with Sysplex CLO, Sysplex ETR, or ISC compatibility protocol encapsulation, or with the OFC safety protocol.
Proper physical configuration of the system is critical to the operation of line card protection. For detailed information on shelf configuration rules, refer to the Cisco ONS 15540 ESPx Planning Guide.
Configuring Y-Cable Based Line Card Protection
The following is an overview of the tasks required to configure y-cable based line card protection:
Step 1
Determine the number of clients you need to support and which channels you will deploy to transport the client data.
Step 2
Ensure that the mux/demux modules needed to support the channels are inserted in the correct subcards of the mux/demux motherboards; also ensure that the line card motherboards are cross connected to the mux/demux modules or mux/demux motherboards. (See the "Considerations for Using Y-Cable Based Line Card Protection" section.)
Step 3
Ensure that the mux/demux modules are correctly interconnected with the external optical patch cables.
Step 4
In order to ensure separate paths to the mux/demux modules, shut down the wavepatch interfaces if you are using splitter protected line card motherboards.
Step 5
Configure the interfaces and the patch connections from the CLI.
Step 6
Configure y-cable protection from the CLI.
Y-cable protection on the Cisco ONS 15540 ESPx requires configuration on the CLI. To configure y-cable protection, use the following commands, beginning in global configuration mode:
Note
Configure both nodes that add and drop the channel with the same revertive behavior.
CautionDo not configure y-cable protection with Sysplex CLO, Sysplex ETR, or ISC compatibility protocol encapsulation, or with the OFC safety protocol.
Example
This example shows how to associate two transparent interfaces for y-cable line card protection with revertive switchover behavior:
Switch#
configure terminalSwitch(config)# redundancy
Switch(config-red)# associate group Yosemite
Switch(config-red-aps)# aps working transparent 3/0/0
Switch(config-red-aps)# aps protection transparent 5/0/0
Switch(config-red-aps)# aps y-cable
Switch(config-red-aps)# aps enable
Displaying the Y-Cable Protection Configuration
To display the y-cable protection configuration, use the following EXEC command:
Examples
The following example shows how to display the y-cable protection for an APS group named Yosemite:
Switch# show aps
AR : APS Role, Wk: Working, Pr: Protection
AS : APS State, Ac: Active, St: Standby
IS : Interface State, Up: Up, Dn: Down
MPL: Minimum Protection Level, SD: Signal Degrade, SF: Signal Failure
LOL: Loss of Light, - not currently protected
Interface AR AS IS MPL Redundant Intf Group Name
~~~~~~~~~~~~~~~~~ ~~ ~~ ~~ ~~~ ~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~
Transparent2/3/0 Wk Ac Up SD Transparent4/3/0 Yosemite
Transparent4/3/0 Pr St Up Transparent2/3/0 Yosemite
Switch# show aps group Yosemite
APS Group Yosemite :
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end (client side y-cable)
direction....: prov: uni, current: uni, remote prov: bi
revertive....: no
created......: 14 hours, 53 minutes
aps state....: associated (enabled)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
switched chan: 0
channel ( 0): Transparent4/3/0 (STANDBY - UP), Wave4/3 (UP)
: channel request: no-request
: transmit request: no-request
: receive request: no-request
channel ( 1): Transparent2/3/0 (ACTIVE - UP), Wave2/3 (UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
The following example shows how to display the y-cable protection for an APS group on a 10-GE card, named y-protect:
Switch# show aps group y-protect
APS Group y-protect :
architecture.:1+1, remote prov:1+1
span.........:end-to-end
prot. mode...:client side y-cable
direction....:prov:uni, current:uni, remote prov:uni
revertive....:no
aps state....:enabled (associated)
request timer:holddown:5000 ms, max:15000 ms, count 2
msg-channel..:auto (up on cdl dcc)
created......:2 minutes
auto-failover:enabled
transmit k1k2:no-request, 0, 0, 1+1, uni
receive k1k2:no-request, 0, 0, 1+1, uni
switched chan:0
protection(0):TenGigEthernetPhy9/1 (STANDBY - UP), WaveEthernetPhy9/1
(UP)
:channel request:no-request
:switchover count:0
:last switchover:never
working...(1):TenGigEthernetPhy10/0 (ACTIVE - UP), WaveEthernetPhy10/0
(UP)
:channel request:no-request
:switchover count:0
:last switchover:never
Configuring Splitter Protected Line Card Motherboards for Line Card Protection
Normally, you would use unprotected line card motherboards for line card protection configurations. However, you can use splitter protected line card motherboards instead by shutting down the wavepatch interfaces to one of the mux/demux motherboards.
To configure line card protection on splitter protected line card motherboards, use the following commands, beginning in global configuration mode:
Command PurposeStep 1
Switch(config)# interface wavepatch slot/subcard/port
Switch(config-if)#
Selects the wavepatch interface to configure and enters interface configuration mode.
Step 2
Switch(config-if)# shutdown
Disables the wavepatch interface.
Step 3
Switch(config-if)# exit
Switch(config)#
Returns to global configuration mode.
Repeat Step 1 through Step 3 for one wavepatch interface per wavepatch pair on splitter protected line card motherboards.
Examples
For the following examples, assume that the line card motherboards shown in Figure 7-2 have splitter protection.
The following example shows how to disable all wavepatch interfaces on the line card motherboard in slot 2 that connect to the mux/demux motherboard in slot 1:
Switch(config)# interface wavepatch 2/0/1
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)# interface wavepatch 2/1/1
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)# interface wavepatch 2/2/1
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)# interface wavepatch 2/3/1
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)#
The following example shows how to disable all wavepatch interfaces on the line card motherboard in slot 4 that connect to the mux/demux motherboard in slot 0:
Switch(config)# interface wavepatch 4/0/0
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)# interface wavepatch 4/1/0
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)# interface wavepatch 4/2/0
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)# interface wavepatch 4/3/0
Switch(config-if)# shutdown
Switch(config-if)# exit
Switch(config)#
About Trunk Fiber Based Protection
The PSM (protection switch module) provides trunk fiber based protection for Cisco ONS 15540 ESPx systems configured in point-to-point topologies. This type of protection only provides protection against trunk fiber cuts, not specific channel failure as provided by splitter and line card based schemes. However, this protection scheme allows for much simpler shelf configurations in topologies where per channel protection is not required.
Figure 7-3 shows trunk fiber based protection configured with a transponder line card.
Figure 7-3 Trunk Fiber Based Protection Scheme
Considerations for Using Trunk Fiber Based Protection
The following considerations apply when using trunk fiber based protection:
•
Trunk fiber based protection does not protect against failures on the shelf itself or the client equipment. To protect against these failures, line card protection should be implemented on the client equipment itself.
•
The APS software that supports trunk fiber based protection can be configured as revertive or nonrevertive. After a switchover, the active traffic can be put back on the previously failed working fiber, once the fault has been remedied, either automatically (revertive) or through manual intervention (nonrevertive).
•
Use PSMs only in point-to-point topologies.
•
The shelves connected to the trunk fiber must use a PSM.
Configuring Trunk Fiber Based Protection
To configure trunk fiber based protection on the PSMs, perform the following steps, beginning in global configuration mode:
Examples
The following example shows how to configure trunk fiber protection:
Switch(config)# redundancy
Switch(config-red)# associate group psm-group
Switch(config-red-aps)# aps working wdmsplit 0/1/0
Switch(config-red-aps)# aps protection wdmsplit 0/1/1
Switch(config-red-aps)# aps message-channel ip far-end group-name psm-group ip-address 172.18.44.93
Switch(config-red-aps)# aps enable
Displaying Trunk Fiber Protection Configuration
To display the trunk fiber configuration, use the following EXEC command:
Command Purposeshow aps {detail | group name | interface wavepatch slot/subcard/port}
Displays detailed APS configuration information for groups and interfaces.
Note
Group names are case sensitive.
Examples
The following example shows how to display the protocol encapsulation configuration of a wdmsplit interface:
Switch# show aps group psm-group
APS Group psm-group :
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end
prot. mode...: network side wdm splitter
direction....: prov: bi, current: bi, remote prov: bi
revertive....: no
aps state....: enabled (associated)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
msg-channel..: ip (up), psm-group, 172.18.44.93
created......: 22 hours, 11 minutes
auto-failover: disabled
transmit k1k2: sf-lp, 0, 0, 1+1, bi
receive k1k2: reverse-request, 0, 0, 1+1, bi
switched chan: 0
protection(0): WdmSplit0/0/1 (STANDBY - DOWN)
: channel request: sf-lp
: switchover count: 7
: last switchover: 18 minutes
working...(1): WdmSplit0/0/0 (ACTIVE - UP)
: channel request: no-request
: switchover count: 7
: last switchover: 18 minutes
Configuring APS Group Attributes
This section describes APS group attributes and how to configure them.
Configuring Revertive Switching
The Cisco ONS 15540 ESPx supports revertive switching for y-cable and trunk fiber protection. When revertive switching is configured, the system automatically switches back from the protection interface to the working interface. This automatic switchover occurs after the condition that caused the switchover to the protection interface is resolved and the switchover-enable timer has expired.
To configure revertive switching, use the following commands, beginning in global configuration mode:
Example
The following example shows how to configure revertive switching for a y-cable protected APS group:
Switch#
configure terminalSwitch(config)# redundancy
Switch(config-red)# associate group blue
Switch(config-red-aps)# aps working transparent 4/0/0
Switch(config-red-aps)# aps protection transparent 8/0/0
Switch(config-red-aps)# aps y-cable
Switch(config-red-aps)# aps revertive
Switch(config-red-aps)# aps enable
Displaying the Revertive Switching Configuration
To display the revertive switching configuration, use the following EXEC command:
Example
The following example shows how to display the path switching configuration for an APS group named blue:
Switch# show aps group blue
APS Group blue:
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end
prot. mode...: client side y-cable
direction....: prov: uni, current: uni, remote prov: uni
revertive....: yes, wtr: 300 secs (not running)
aps state....: enabled (associated)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
msg-channel..: auto (up on osc)
created......: 4 days, 23 hours, 16 minutes
auto-failover: enabled
transmit k1k2: no-request, 0, 0, 1+1, uni
receive k1k2: no-request, 0, 0, 1+1, uni
switched chan: 0
protection(0): Transparent8/0/0 (STANDBY - UP), Wave8/0 (UP)
: channel request: no-request
: switchover count: 2
: last switchover: 3 days, 23 hours, 16 minutes
working...(1): Transparent4/0/0 (ACTIVE - UP), Wave4/0 (UP)
: channel request: no-request
: switchover count: 1
: last switchover: 4 days, 53 minutes
About Path Switching
The Cisco ONS 15540 ESPx supports per-channel unidirectional and bidirectional 1+1 path switching. When a signal is protected and the signal fails, or in some cases degrades, on the active path, the system automatically switches from the active network path to the standby network path.
Signal failures can be total loss of light caused by laser failures, by fiber cuts between the Cisco ONS 15540 ESPx and the client equipment, or by other equipment failure. Loss of light failures cause switchovers for both splitter protected and y-cable protected signals.
For y-cable protected signals, you can also configure alarm thresholds to cause a switchover when the signal error rate reaches an unacceptable level. For information about configuring alarm thresholds, see the "Configuring Alarm Thresholds" section on page 4-10.
Note
Both interfaces on both nodes must be configured with alarm thresholds for signal error rate switchovers to occur.
The Cisco ONS 15540 ESPx implements path switching using an APS channel protocol over the in-band message channel, the OSC (optical supervisory channel) on the protection path, or the IP management connection.
Note
Bidirectional path switching operates only on Cisco ONS 15540 ESPx networks that have the OSC or the in-band message channel, or send the APS message over the IP management connection. You must also configure the patch connection between the OSC and the mux/demux motherboard if you are using the OSC for APS messages.
Figure 7-4 shows a simple point-to-point configuration with splitter protection. The configured working path carries the active signal, and the configured protection path carries the standby signal.
Figure 7-4 Active and Standby Path Configuration Example
Figure 7-5 shows the behavior of unidirectional path switching when a loss of signal occurs. For the two node example network, unidirectional path switching operates as follows:
•
Node 2 sends the channel signal over both the active and standby paths.
•
Node 1 receives both signals and selects the signal on the active path.
•
Node 1 detects a loss of signal light on its active path and switches over to the standby path.
•
Node 2 does not switch over and continues to use its original active path.
Now the nodes are communicating along different paths.
Figure 7-5 Unidirectional Path Switching Example
Figure 7-6 shows the behavior of bidirectional path switching when a loss of signal occurs. For the two node example network, bidirectional path switching operates as follows:
•
Node 2 sends the channel signal over both the active and standby paths.
•
Node 1 receives both signals and selects the signal on the active path.
•
Node 1 detects a loss of signal light on its active path and switches over to the standby path.
•
Node 1 sends an APS switchover message to node 2 on the protection path.
•
Node 2 switches from the active path to the standby path.
Both node 1 and node 2 communicate on the same path.
Figure 7-6 Bidirectional Path Switching Overview
Configuring Path Switching
To configure unidirectional or bidirectional path switching, use the following commands, beginning in global configuration mode:
Command PurposeStep 1
Switch(config)# redundancy
Switch(config-red)#
Enters redundancy configuration mode.
Step 2
Switch(config-red)# associate group name
Switch(config-red-aps)#
Selects the interfaces to associate and enters APS configuration mode.
Note
The group name is case sensitive.
Step 3
Switch(config-red-aps)# aps disable
Disables APS activity between the interfaces.
Note
For newly associated pairs, APS activity is disabled by default.
Step 4
Switch(config-red-aps)# aps direction {unidirectional | bidirectional}
Specifies the type of path switching. The default behavior is unidirectional.
Step 5
Switch(config-red-aps)# aps working {transparent slot/subcard/0 | wavepatch slot/subcard/port | tengigethernetphy slot/subcard | wdmsplit slot/subcard/port}
Configures the working path interface.
Step 6
Switch(config-red-aps)# aps protection {transparent slot/subcard/0 | wavepatch slot/subcard/port | tengigethernetphy slot/subcard | wdmsplit slot/subcard/port}
Configures the protection path interface.
Step 7
Switch(config-red-aps)# aps timer oscp holddown milliseconds count number
Changes the APS channel protocol holddown timer and message count values. The default is 5000 milliseconds and a count of 2
Step 8
Switch(config-red-aps)# aps timer oscp max-interval seconds
Changes the APS channel protocol maximum interval timer for waiting for a message. The default is 15 seconds.
Repeat Step 1 through Step 8 on the corresponding transparent interface on the other node that adds and drops, or terminates, the channel.
Step 9
Switch(config-red-aps)# aps enable
Enables APS activity between the interfaces.
Note
Both nodes in the network that add and drop the channel must have the same APS configuration. Specifically, both must have the same path switching behavior, and working and protection paths.
Note
For interfaces with either Sysplex ETR or Sysplex CLO protocol encapsulation, configure bidirectional path switching to ensure proper functioning of the protocol.
Examples
Figure 7-7 shows the active and standby paths between node 1 and node 2 with splitter protection.
Figure 7-7 Bidirectional Path Switching Example with Splitter Protection
The following example shows how to configure one channel in the example network for bidirectional path switching using the default working and protection path interfaces:
Node1#
configure terminalNode1(config)# redundancy
Node1(config-red)# associate group red
Node1(config-red-aps)# aps working wavepatch 5/0/0
Node1(config-red-aps)# aps protection wavepatch 5/0/1
Node1(config-red-aps)# aps bidirectional
Node1(config-red-aps)# aps enable
Node2#
configure terminalNode2(config)# redundancy
Node2(config-red)# associate group blue
Node2(config-red-aps)# aps working wavepatch 5/0/0
Node2(config-red-aps)# aps protection wavepatch 5/0/1
Node2(config-red-aps)# aps bidirectional
Node2(config-red-aps)# aps enable
Figure 7-8 shows the active and standby paths between node 1 and node 2 with y-cable protection.
Figure 7-8 Bidirectional Path Switching Example with Y-Cable Protection
The following example shows how to configure one channel in the example network for bidirectional path switching and configure the working and protection path interfaces:
Node1#
configure terminalNode1(config)# redundancy
Node1(config-red)# associate group alpha
Node1(config-red-aps)# aps working transparent 5/0/0
Node1(config-red-aps)# aps protection transparent 3/0/0
Node1(config-red-aps)# aps direction bidirectional
Node1(config-red-aps)# aps y-cable
Node1(config-red-aps)# aps enable
Node2#
configure terminalNode2(config)# redundancy
Node2(config-red)# associate group alpha
Node2(config-red-aps)# aps working transparent 5/0/0
Node2(config-red-aps)# aps protection transparent 3/0/0
Node2(config-red-aps)# aps direction bidirectional
Node2(config-red-aps)# aps y-cable
Node2(config-red-aps)# aps enable
Changing the Path Switching Direction for Y-Cable Protection
To change the path switching direction for a y-cable protection configuration, use the following commands:
Command PurposeStep 1
Switch# show aps group name
Displays the current standby interface in the APS group information.
Step 2
Switch# configure terminal
Switch(config)#
Enters global configuration mode.
Step 3
Switch(config)# interface transparent slot/subcard/0
Switch(config-if)#
Enters interface configuration mode for the standby interface.
Step 4
Switch(config-if)# shutdown
Disables the interface.
Step 5
Switch(config-if)# exit
Switch(config)#
Exits interface configuration mode.
Step 6
Switch(config)# redundancy
Switch(config-red)#
Enters redundancy configuration mode.
Step 7
Switch(config-red)# associate group name
Switch(config-red-aps)#
Selects the interfaces to associate and enters APS configuration mode.
Note
The group name is case sensitive.
Step 8
Switch(config-red-aps)# aps disable
Disables APS activity between the interfaces.
Note
For newly associated pairs, APS activity is disabled by default.
Step 9
Switch(config-red-aps)# aps direction {unidirectional | bidirectional}
Specifies the new path switching operation.
Step 10
Switch(config-red-aps)# aps enable
Enables APS activity between the interfaces.
Step 11
Switch(config-red-aps)# exit
Switch(config)#
Exits APS configuration mode.
Step 12
Switch(config-red)# exit
Switch(config)#
Exits redundancy configuration mode.
Step 13
Switch(config)# interface transparent slot/subcard/0
Switch(config-if)#
Enters interface configuration mode for the standby interface.
Step 14
Switch(config-if)# no shutdown
Disables the interface.
Step 15
Switch(config-if)# end
Switch#
Returns to privileged EXEC mode.
Repeat Step 1 through Step 15 on the corresponding transparent interface on the other node that adds and drops, or terminates, the channel.
Example
The following example shows how to change the path switching operation for a y-cable APS group from unidirectional to bidirectional:
Node1# show aps group Denver
APS Group Denver :
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end (client side y-cable)
direction....: prov: uni, current: uni, remote prov: uni
revertive....: no
created......: 14 hours, 53 minutes
aps state....: associated (enabled)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
switched chan: 0
channel ( 0): Transparent4/3/0 (STANDBY - UP), Wave4/3 (UP)
: channel request: no-request
: transmit request: no-request
: receive request: no-request
channel ( 1): Transparent2/3/0 (ACTIVE - UP), Wave2/3 (UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
Node1#
configure terminal
Node1
(config)#
interface transparent 4/3/0
Node1
(config-if)#
shutdown
Node1
(config-if)#
exitNode1(config)# redundancy
Node1(config-red)# associate group Denver
Node1(config-red-aps)# aps disable
Node1(config-red-aps)# aps direction bidirectional
Node1(config-red-aps)# aps enable
Node1(config-red-aps)# exit
Node1(config-red)# exit
Node1
(config)#
interface transparent 4/3/0
Node1
(config-if)#
no shutdown
Node1
(config-if)#
end
Node1#
Node2# show aps group Denver
APS Group Denver :
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end (client side y-cable)
direction....: prov: uni, current: uni, remote prov: bi
revertive....: no
created......: 14 hours, 53 minutes
aps state....: associated (enabled)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
switched chan: 0
channel ( 0): Transparent4/3/0 (STANDBY - UP), Wave4/3 (UP)
: channel request: no-request
: transmit request: no-request
: receive request: no-request
channel ( 1): Transparent2/3/0 (ACTIVE - UP), Wave2/3 (UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
Node2#
configure terminal
Node2
(config)#
interface transparent 4/3/0
Node2
(config-if)#
shutdown
Node2
(config-if)#
exitNode2(config)# redundancy
Node2(config-red)# associate group Denver
Node2(config-red-aps)# aps disable
Node2(config-red-aps)# aps direction bidirectional
Node2(config-red-aps)# aps enable
Node2(config-red-aps)# exit
Node2(config-red)# exit
Node2
(config)#
interface transparent 4/3/0
Node2
(config-if)#
no shutdown
Node2
(config-if)#
end
Node2#
Displaying the Path Switching Configuration
To display the path switching configuration, use the following EXEC command:
Example
The following example shows how to display the path switching configuration for an APS group named blue:
Switch# show aps group blue
APS Group blue:
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end
direction....: prov: bi, current: bi, remote prov: bi
revertive....: no
created......: 26 minutes
aps state....: associated
request timer: holddown: 5000 ms, max: 15 secs, count 2
switched chan: 0
channel ( 0): Wavepatch8/0/1 (STANDBY - UP)
: channel request: no-request
: transmit request: no-request
: receive request: no-request
channel ( 1): Wavepatch8/0/0 (ACTIVE - UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
Configuring the Switchover-Enable Timer
The switchover-enable timer on the Cisco ONS 15540 ESPx prevents any automatic switchover from the protection path to the working path until it has expired. When it expires, switchovers occur only if there is no fault on the working path and there is no overriding switchover request in effect.
To configure the switchover-enable timer, use the following commands, beginning in global configuration mode:
Example
The following example shows how to configure the minimum interval value for the switchover-enable timer for an APS group.
Switch(config)# redundancy
Switch(config-red)# associate group yc
Switch(config-red-aps)# aps disable
Switch(config-red-aps)# aps timer switchover-enable min-interval 10
Switch(config-red-aps)# aps enable
Displaying the Switchover-Enable Timer Configuration
To display the switchover-enable timer configuration, use the following EXEC command:
Example
The following example shows how to display the switchover-enable timer configuration for an APS group:
Switch# show running-config
Building configuration...
Current configuration : 3403 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
service internal
!
hostname M1
!
redundancy
keepalive-timer 4000
keepalive-threshold 12
associate group yc
aps working Transparent8/0/0
aps protection Transparent8/3/0
aps y-cable
aps enable
![]()
aps timer switchover-enable min-interval 10
<Information deleted.>
Configuring the Wait-to-Restore Timer
The wait-to-restore timer on the Cisco ONS 15540 ESPx prevents oscillations when revertive switching is enabled for y-cable line card protection configurations. If the preferred working signal in a y-cable line card protection configuration is unstable, the wait-to-restore timer prevents possible data loss that could result from frequent switchovers.
To configure the wait-to-restore timer, use the following commands, beginning in global configuration mode:
Example
The following example shows how to configure the wait-to-restore timer value for an APS group.
Switch(config)# redundancy
Switch(config-red)# associate group blue
Switch(config-red-aps)# aps disable
Switch(config-red-aps)# aps timer wait-to-restore 240
Switch(config-red-aps)# aps enable
Displaying the Wait-to-Restore Timer Configuration
To display the wait-to-restore timer configuration, use the following EXEC command:
Example
The following example shows how to display the wait-to-restore timer configuration for an APS group named blue:
Switch# show aps group blue
APS Group blue:
architecture.: 1+1, remote prov: unknown
span.........: end-to-end
prot. mode...: client side y-cable
direction....: prov: uni, current: uni, remote prov: unknown
revertive....: yes, wtr: 240 secs (running - 232 secs left)
aps state....: enabled (associated)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
msg-channel..: auto (down)
created......: 4 days, 25 minutes
auto-failover: enabled
transmit k1k2: wait-to-restore, 1, 1, 1+1, uni
receive k1k2: no-request, 0, 0, unknown, unknown
switched chan: 1
protection(0): Transparent8/3/0 (ACTIVE - UP), Wave8/3 (UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
working...(1): Transparent9/3/0 (STANDBY - UP), Wave9/3 (UP)
: channel request: wait-to-restore
: switchover count: 1
: last switchover: 4 days, 25 minutes
Configuring the Search-For-Up Timer
The search-for-up timer on the Cisco ONS 15540 ESPx causes the system to wait for a splitter protection connection to come up before checking the other splitter protection connection.
When both members of a splitter pair are down, the system first checks one signal for the minimum time interval. If the splitter protection connection does not come up, the system checks the other connection and doubles the time interval. This process repeats until the maximum timer interval is reached or exceeded. Checking continues at the maximum timer interval until one of the splitter protection connections becomes active.
To configure the search-for-up timer, use the following commands, beginning in global configuration mode:
Example
The following example shows how to configure the search-for-up timer value for an APS group.
Switch(config)# redundancy
Switch(config-red)# associate group yc
Switch(config-red-aps)# aps disable
Switch(config-red-aps)# aps timer search-for-up 4 16
Switch(config-red-aps)# aps enable
Displaying the Search-For-Up Timer Configuration
To display the search-for-up timer configuration, use the following EXEC command:
Example
The following example shows how to display the search-for-up configuration for an APS group:
Switch# show aps group splitter
APS Group splitter :
architecture.: 1+1, remote prov: unknown
span.........: end-to-end
prot. mode...: network side splitter
direction....: prov: uni, current: uni, remote prov: unknown
revertive....: no
aps state....: enabled (associated)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
search-up-int: min: 4 secs, max: 16 secs
msg-channel..: auto (down)
created......: 3 minutes
auto-failover: enabled
transmit k1k2: no-request, 0, 0, 1+1, uni
receive k1k2: no-request, 0, 0, unknown, unknown
switched chan: 0
protection(0): Wavepatch8/0/1 (STANDBY - UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
working...(1): Wavepatch8/0/0 (ACTIVE - UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
Configuring the Message Timers
The Cisco ONS 15540 ESPx provides two message timers, the APS message holddown timer and the APS message maximum inactivity interval timer. The APS message holddown timer prevents APS channel protocol message flooding. The maximum inactivity interval timer determines how often to send the inactivity messages to ensure that the APS channel protocol is still functioning between the nodes.
To configure the message timers, use the following commands, beginning in global configuration mode:
Example
The following example shows how to configure the message timer values for an APS group.
Switch(config)# redundancy
Switch(config-red)# associate group yc
Switch(config-red-aps)# aps disable
Switch(config-red-aps)# aps timer message holddown 4000 3
Switch(config-red-aps)# aps timer message max-interval 10
Switch(config-red-aps)# aps enable
Displaying the Message Timer Configuration
To display the message timer configuration, use the following EXEC command:
Example
The following example shows how to display the message timer configuration for an APS group:
Switch# show aps group blue
APS Group blue :
architecture.: 1+1, remote prov: unknown
span.........: end-to-end
prot. mode...: network side splitter
direction....: prov: uni, current: uni, remote prov: unknown
revertive....: no
aps state....: enabled (associated)
request timer: holddown: 4000 ms, max: 10000 ms, count 3
search-up-int: min: 2 secs, max: 32 secs
msg-channel..: auto (down)
created......: 3 minutes
auto-failover: enabled
transmit k1k2: no-request, 0, 0, 1+1, uni
receive k1k2: no-request, 0, 0, unknown, unknown
switched chan: 0
protection(0): Wavepatch8/0/1 (STANDBY - UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
working...(1): Wavepatch8/0/0 (ACTIVE - UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
Switchovers and Lockouts
In APS, you can switch a channel signal from one path to another, or you can lock out a switchover altogether while performing system maintenance.
A switchover of the channel signal from the working path to protection path is useful when
upgrading or maintaining the system, or in cases where a signal failure caused a switchover. In the case of splitter protection, once the cause of the problem has been corrected, the system does not automatically revert to using the original working path. The switchover to the formerly failed interface must be requested from the CLI. The interface originally configured as the working path might be preferred because of its link loss characteristics or because of its distance advantage. For example, some protocols, such as ESCON, experience lower data throughput at increasing distances, so moving the signal back to the shorter path might be advised.
A lockout prevents a switchover of the active signal from the working path to the protection path. This is useful when upgrading or maintaining the system, or when the signal on the protection path has degraded or failed.
The Cisco ONS 15540 ESPx supports APS switchover and lockout requests from the CLI. These requests have priorities depending on the condition of the protection signal and the existence of other switchover requests. There are three types of switchover requests:
•
Lockout requests—Have the highest priority and take effect regardless of the condition of the protection signal. A lockout prevents the active signal from switching over from the working path to the protection path.
•
Forced switchover requests—Have the next highest priority and are only prevented if there is an existing lockout on the protection path, or the signal on the protection path has failed when switching from working to protection.
•
Manual switchover requests—Have the lowest priority and only occur if there is no protection path lockout, a forced switchover, or the signal has failed or degraded.
In summary, the priority order is:
1.
Lockout
2.
Signal failure on the protection path
3.
Forced switchover
4.
Signal failure on the working path
5.
Signal degrade on the working or protection path
6.
Manual switchover
If a request or condition of a higher priority is in effect, a lower priority request is rejected.
Note
APS lockouts and switchovers do not persist across processor card switchovers or system reloads.
Requesting a Switchover or Lockout
To prevent switchovers to the protection signal, or to request a signal switchover, use the following commands in privileged EXEC mode:
Examples
The following example shows how to request a forced switchover from working to protection except if a lockout is in effect on the protection path:
Switch# aps switch blue force working-to-protection
The following example shows how to prevent a switchover to the protection path:
Switch# aps lockout Wavepatch3/0/0
Displaying Switchover and Lockout Request Status
To display a pending switchover request, use the following command in privileged EXEC mode:
The following example shows how to display the switchover request status on an APS group:
Switch# show aps group yellow
APS Group yellow:
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end (client side y-cable)
direction....: prov: uni, current: uni, remote prov: bi
revertive....: no
created......: 15 hours, 1 minute
aps state....: associated (enabled)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
switched chan: 0
channel ( 0): Transparent4/3/0 (STANDBY - UP), Wave4/3 (UP)
: channel request: lockout-of-protection
: transmit request: lockout-of-protection
: receive request: no-request
channel ( 1): Transparent2/3/0 (ACTIVE - UP), Wave2/3 (UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
Clearing Switchovers and Lockouts
A lockout or a forced or manual switchover request stays in effect until the system reboots. You can manually clear these requests from the CLI.
To clear an APS switchover or lockout, use the following privileged EXEC command:
Command Purposeaps clear group-name
Clears APS switch request or lockout on an associated interface pair.
Example
The following example shows how to clear the switchover requests on an associated interface pair using the default group name:
Switch# aps clear Wavepatch10/0/0
Displaying Switchover and Lockout Clear Status
To display a pending switchover request, use the following command in privileged EXEC mode:
The following example shows how to display the switchover requests status on an APS group:
Switch# show aps group blue
APS Group blue :
architecture.: 1+1, remote prov: 1+1
span.........: end-to-end (client side y-cable)
direction....: prov: uni, current: uni, remote prov: bi
revertive....: no
created......: 15 hours, 1 minute
aps state....: associated (enabled)
request timer: holddown: 5000 ms, max: 15000 ms, count 2
switched chan: 0
channel ( 0): Transparent10/0/0 (STANDBY - UP)
: channel request: no-request
: transmit request: no-request
: receive request: no-request
channel ( 1): Transparent8/0/0 (ACTIVE - UP)
: channel request: no-request
: switchover count: 0
: last switchover: never
Posted: Wed Apr 26 03:30:15 PDT 2006
All contents are Copyright © 1992--2006 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.