|
|
This appendix includes checklists, instructions, examples, and blank worksheets used for the initial installation and subsequent maintenance of the Cisco 6400 carrier-class broadband aggregator. The checklists, worksheets, and site log provide reference and history information that can be useful when you are troubleshooting the Cisco 6400.
This appendix includes the following items:
Make copies of the worksheets provided here. Complete them and keep them for future reference.
Use the Cisco 6400 Installation Checklist provided here to verify that you have all the information you need to install and configure the Cisco 6400, and that all the components are installed and operating correctly. Each task in the Cisco 6400 installation checklist should be verified by the person performing the installation and then dated for the permanent site record.
| Task | Verified By | Date |
|---|---|---|
Date Cisco 6400 was received |
|
|
System and all components are unpacked |
|
|
Accessories verified |
|
|
Chassis components verified |
|
|
Safety recommendations reviewed |
|
|
Cisco 6400 Installation Checklist copied |
|
|
Site log copied and information entered |
|
|
Site power voltages verified |
|
|
Site environmental specs verified |
|
|
IP address assigned |
|
|
Required tools available |
|
|
Network connection equipment available |
|
|
System mounted in rack |
|
|
NSP installed and operational |
|
|
PEM installed and operational |
|
|
All ejector levers checked |
|
|
Captive installation screws on cards and PEMs tightened |
|
|
Interface cables and devices connected |
|
|
Node attached to console port |
|
|
System boot successful |
|
|
Redundant NSP card installed and operational (optional) |
|
|
NRP card installed and operational (optional) |
|
|
OC-3C NLC installed and operational (optional) |
|
|
Use the Cisco 6400 component checklist to verify that all hardware accessories and documentation needed have been received before you begin the installation process.
Each component in the Cisco 6400 component checklist should be verified by the person unpacking the equipment and kept for the permanent site record.
| Component | Description | Received |
|---|---|---|
Chassis | Switch chassis |
|
| Accessories Box | ||
Power cables | One power cable for each PEM received (may be shipped separately) |
|
Other optional equipment | Additional cards ordered |
|
Ethernet transceiver |
| |
Documentation | Unpacking Instructions |
|
Cisco 6400 Hardware Installation and Maintenance Guide |
| |
Cisco 6400 Site Planning Guide |
| |
Regulatory Compliance and Safety Information for the Cisco 6400 |
| |
Software license agreement |
| |
| System Components | ||
Node switch processor (NSP) card | Individually boxed |
|
PEM | Individually boxed |
|
Other equipment |
|
|
System Name: __________________________________________
IP Address: _____________________________________________
Location: _______________________________________________
Serial Number: __________________________________________
| Slot/Subslot | Port Number | Card Type | Name | Speed |
|---|---|---|---|---|
Slot A |
| NSP |
|
|
Slot B |
|
|
|
|
Slot 1/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 1/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
Slot 2/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 2/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
Slot 3/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 3/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
Slot 4/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 4/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
Slot 5/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 5/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
Slot 6/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 6/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
Slot 7/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 7/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
Slot 8/Subslot 0 | 0 |
|
|
|
| 1 |
|
|
|
Slot 8/Subslot 1 | 0 |
|
|
|
| 1 |
|
|
|
| Date | Description of Action Performed or Symptom Observed | Initials |
|---|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The installation and configuration of the Cisco 6400 can be separated into specific steps. If you complete each step described in the quick installation worksheet, following the instructions provided in this publication, Cisco 6400 installation should be successful. If the Cisco 6400 does not function properly at the first attempt, you can use the worksheet to systematically check that each step was performed correctly.
| Task | Completed | Date |
|---|---|---|
Complete switch installation checklist |
|
|
Complete switch component checklist |
|
|
Complete port configuration worksheets |
|
|
Rack-mount the switch |
|
|
Connect cables |
|
|
Connect power cables |
|
|
Switch power on |
|
|
Configure IP address (optional) |
|
|
Configure ATM address (optional) |
|
|
Configure line [aux/console] |
|
|
Configure SNMP |
|
|
Set clock (optional) |
|
|
Test the configuration |
|
|
Store configuration |
|
|
Posted: Fri Jul 5 10:57:24 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.