cc/td/doc/product/dsl_prod/6200
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Pin Assignments

Pin Assignments

This appendix describes the electrical connections of ports on the Cisco 6200 advanced digital subscriber line access multiplexer (DSLAM).

This appendix provides the following pin assignments:

Refer to Figure A-1 for the locations of the connectors on the rear of the chassis.

Items Not Used in This Release

The following fixtures are not used in this release. Except where otherwise indicated, these items are located on the rear panel of the DSLAM.

Caution Do not remove the terminators from the BNC connectors. Doing so prevents the cards within the chassis from communicating with each other.

Figure A-1:
Rear View of Cisco 6200 Chassis Showing Connector Placement

A.1 UTP Connectors for Subscriber Traffic

Ten 50-pin Champ connectors on the backplane provide unshielded twisted pair (UTP) connections that carry ADSL signals (subscriber traffic) between the Cisco 6200 DSLAM and the POTS splitter. Attached to each connector is a dangler cable. One end of the dangler cable mates with the Cisco 6200 backplane; the other end terminates with a female 50-pin Champ connector.

Each Champ connector on the backplane, and thus each dangler cable, serves one subscriber line card (SLC) slot in the Cisco 6200 chassis. The ten dangler cables, J1 through J10, serve slots 5 through 14 respectively. The pinout for the connectors is provided in Table A-1.


Table A-1:
Pin Assignments for Connectors J1 to J10
Pin Number Wire Color TIP/RING Port
Number
Pin Number Wire Color TIP/RING Port Number

26

1

White/blue

Blue/white

TIP

RING

00

39

14

Black/brown

Brown/black

TIP

RING

13

27

2

White/orange

Orange/white

TIP

RING

01

40

15

Black/gray

Gray/black

TIP

RING

14

28

3

White/green

Green/white

TIP

RING

02

41

16

Yellow/blue

Blue/yellow

TIP

RING

15

29

4

White/brown

Brown/white

TIP

RING

03

42

17

Yellow/orange

Orange/yellow

TIP

RING

-

30

5

White/gray

Gray/white

TIP

RING

04

43

18

Yellow/green

Green/yellow

TIP

RING

-

31

6

Red/blue

Blue/red

TIP

RING

05

44

19

Yellow/brown

Brown/yellow

TIP

RING

-

32

7

Red/orange

Orange/red

TIP

RING

06

45

20

Yellow/gray

Gray/yellow

TIP

RING

-

33

8

Red/green

Green/red

TIP

RING

07

46

21

Violet/blue

Blue/violet

TIP

RING

-

34

9

Red/brown

Brown/red

TIP

RING

08

47

22

Violet/orange

Orange/violet

TIP

RING

-

35

10

Red/gray

Gray/red

TIP

RING

09

48

23

Violet/green

Green/violet

TIP

RING

-

36

11

Black/blue

Blue/black

TIP

RING

10

49

24

Violet/brown

Brown/violet

TIP

RING

-

37

12

Black/orange

Orange/black

TIP

RING

11

50

25

Violet/gray

Gray/violet

TIP

RING

-

38

13

Black/green

Green/black

TIP

RING

12


A.2 Alarm Relay Connector

Table A-2 lists the pin assignments for backplane connector J39, the alarm relay connector. The alarm relays provide relay contact closures. If you connect the alarm relays, they transmit critical, major, and minor alarms to a separate, external alarm device. The alarm device uses a bell, light, or some other signal to alert people to the change in status. For general information on the alarm relay feature, see "Alarm Relay Connection" in "Hardware Description."

The alarm relay connector provides an alarm cut-off circuit that you can wire to your external alarm device. Connect the alarm device so that it can close the contact between pins 13 (ACO C) and 30 (ACO O) on the Cisco 6200 alarm relay.

The alarm relay connector also provides one set of contacts for audible alarms and one set for visual alarms. In Table A-2, audible alarms signals begin with "AUD" and visible alarm signals begin with "VIS." You can use either or both sets of contacts.

You can wire the alarm relay contacts as normally open (NO) or normally closed (NC). Common (CO) pins are used in both cases:

Wiring Method Pins to Use

Normally open

18 through 23 (NO)
9 through 11 (CO)
26 through 28 (CO)

Normally closed

1 through 6 (NC)
9 through 11 (CO)
26 through 28 (CO)


Table A-2:
Pin Assignments for the Alarm Relay Connector
Pin Number Signal Pin Number Signal

1

VIS CRITICAL NC A

18

VIS CRITICAL NO A

2

VIS MAJOR NC A

19

VIS MAJOR NO A

3

VIS MINOR NC A

20

VIS MINOR NO A

4

AUD CRITICAL NC A

21

AUD CRITICAL NO A

5

AUD MAJOR NC A

22

AUD MAJOR NO A

6

AUD MINOR NC A

23

AUD MINOR NO A

7

Reserved NC A

24

Reserved NO A

8

Unused

25

Reserved NO A

9

VIS MAJOR CO A

26

VIS CRITICAL CO A

10

AUD CRITICAL CO A

27

VIS MINOR CO A

11

AUD MINOR CO A

28

AUD MAJOR CO A

12

Reserved NC A

29

Unused

13

ACO C

30

ACO O

14

Digital GND

31

Digital GND

15

Digital GND

32

Digital GND

16

Digital GND

33

Digital GND

17

Digital GND

34

Digital GND


A.3 Auxiliary Port

J40 is a 9-pin male connector on the backplane for an EIA/TIA-232 serial port connecting to the management processor card (MPC). J40 is an auxiliary port that can be used to connect devices such as terminals, modems, or laptop computers to the Cisco 6200. Table A-3 shows the pin assignments.


Table A-3:
Pin Assignments for the Auxiliary Port
Pin Number Signal

1

DCD

2

RXD

3

TXD

4

DTR

5

GND

6

DSR

7

RTS

8

CTS

9

RING


A.4 Console Port

The console port, a serial EIA/TIA-232, uses an RJ-45 connector on the MPC faceplate. Table A-4 shows the pin assignments.


Table A-4: Pin Assignments for the MPC Console Connector
Pin Number Signal

1

RTS

2

DTR

3

TXD

4

GND

5

GND

6

RXD

7

DSR

8

CTS


A.5 Ethernet Management Port

The Ethernet port, a 10BaseT interface with an RJ-45 connector, is on the MPC faceplate. It is used to connect the Cisco 6200 to the management station, a PC running Cisco 6200 Manager software. Table A-5 shows the pin assignments.


Table A-5: Pin Assignments for the MPC Management Ethernet Connector
Pin Number Signal

1

TX+

2

TX-

3

RX+

4

Unused

5

Unused

6

RX-

7

Unused

8

Unused



hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1998 © Cisco Systems Inc.