|
|
2Install the Cisco CTE Series Hardware
3Upgrade the Cisco CTE Series Software
4Configure the CTE for the First Time
The Cisco Content Transformation Engine (CTE) Series handles application and web page requests from devices with microbrowser screens and uses transformation instructions to convert applications into device-appropriate formats. Transformation instructions are created in the companion PC-based application, Design Studio.
This document provides instructions for installing the CTE and performing the initial configuration.
This section describes how to install the CTE hardware in your network environment.
To set up the CTE, you need the following hardware in addition to the items delivered with the CTE:
The following steps summarize the hardware installation procedure described in the Cisco CTE Series Hardware Installation Guide:
Step 2 Use network cables to connect the CTE NIC 1 (e0) port to your network (such as to a server load balancer). For information on using the NIC 2 (e1) port, refer to the Cisco CTE Series Administration Guide.
Step 3 Connect a null-modem cable to the 9-pin serial port on the CTE and connect the cable to a computer that is capable of running terminal emulation software.
Step 4 On the computer, start a terminal emulation application. For example, start HyperTerminal.
Step 5 Set the serial connection to 9600 bits per second, 8 data bits, no parity, 1 stop bit; set the Backspace key to issue a Delete character.
Hardware flow control is optional.
Step 6 Power up the CTE.
After about ten minutes, the CTE serial console appears on the computer terminal.
You are now ready to configure the CTE with your network. If you are upgrading the CTE, go to section 3. Otherwise, skip to section 4.
If you are installing a new device, rather than an upgrade, skip this section.
To upgrade to Release 3.0, you need the Release 3.0 Restore CD-ROM.
 |
Note Be aware that an upgrade is a complete new installation, and it will overwrite any previous CTE settings. Record your configuration settings before you upgrade. |
To upgrade your CTE, perform these steps:
Step 2 Record your configuration settings.
Step 3 Insert the CTE Release 3.0 Restore CD into the CD-ROM drive of the CTE.
Step 4 Power down the CTE.
Step 5 Wait 10 seconds.
Step 6 Power on the CTE.
Step 7 When the installation has completed, the serial console displays the message "Installation successful."
Step 8 When the upgrade is complete, eject the Restore CD and reboot the CTE.
When the CTE restarts, the CTE serial console opens.
You are now ready to configure the CTE with your network.
This section describes the minimum configuration required to establish and test a connection between your CTE and another device such as a server load balancer, switch, or web server.
To configure the CTE, perform these general steps:
Step 2 Enter the IP address and netmask for Interface 0 when prompted:
Step 3 Enter the IP address of the gateway device when prompted.
Step 4 If you use name resolution, enter the IP address for the DNS server when prompted. Otherwise, press Enter to leave the value unset.
Step 5 You can define two other DNS servers when prompted if you wish. To leave these values unset, press Enter at each prompt.
Step 6 Enter the name, if any, that you want to use as your default domain name, such as www.fox.com.
Step 7 Type 1 and then 6 to ping the connected device.
If the ping command is successful, you have completed the initial configuration. If you are unable to ping the connected device, refer to the CTE Series Administration Guide for troubleshooting information.
For detailed information on other configuration settings, see the CTE Series Administration Guide.
Continue configuring the CTE from the web-based Administration Tool. The following steps represent a minimal configuration. If you installed an upgrade, refer to your record of the previous configuration for the settings required for your environment.
- ipAddress is the IP address of your CTE
- 9001 is the administration port
Step 2 If a Security Alert dialog box appears, click Yes.
Step 3 Click the Network tab.
Step 4 Log in as root, and enter the root password that you defined in the CTE serial console.
Step 5 On the Interfaces screen of the Network tab, define the Masquerade Host for Interface 0. The masquerade host is an IP address or host name that can be used for Network Address Translation (NAT).
Step 6 Click Submit to save your changes. Although a Restart Server button appears, you do not need to restart the server yet.
Step 7 Click Submit to save your changes and then click Restart Server.
Step 8 After the server restarts, click the Administration tab.
Step 9 If a Security Alert dialog box appears, click Yes.
Step 10 On the Users screen of the Administration tab, specify a username and password for each Design Studio user. Enter a username of at least 6 characters and a password of at least 8 characters. Click the Add User button.
Step 11 From your web browser, enter the following to check network connectivity:
For example, if the IP address of your CTE is 192.168.10.0 and its HTTP port is 80, enter http://192.168.10.0:80.
If ScreenTop appears, the CTE is properly configured. If ScreenTop does not appear, check the settings.
Step 12 Continue to the next section to install Design Studio.
Design Studio is the application that creates transformation rules. You also use Design Studio to customize the default ScreenTop that can serve as a portal for devices connecting to the CTE.
Design Studio requires the following:
The network connection can be through a proxy server, which you specify when you log in to Design Studio.
To install Design Studio, perform these steps:
If auto-start is enabled on your computer, the installer starts.
If auto-start is not enabled on your computer, double-click the drive icon for your CD-ROM, and then double-click CiscoCTEDesignStudio.exe.
Step 2 Follow the instructions in the installer.
You may be asked to restart your PC during the installation. After you restart your PC, the Design Studio installation wizard continues the installation.
By default, Design Studio is installed in C:\Program Files\Cisco\CTE\Design Studio.
See the Design Studio Getting Started Guide for detailed information on installing and starting Design Studio, as well as an overview of the product and a tutorial. For detailed information on using Design Studio to create, preview, and publish transformation rules, see the Design Studio User Guide. That information is also available from the Design Studio Help menu.
To start Design Studio, you need the following login information from the administrator who sets up the CTE:
|
Note Design Studio is intended for use by one user at a time. Do not attempt to run multiple instances of Design Studio from one installation. |
To start Design Studio, perform these steps:
Step 2 Enter your username and password.
Step 3 Enter the IP address of the CTE.
Step 4 If necessary, change the upload port number.
The default upload port number is 9001. You might need to change the port number if your firewall redirects ports. Contact your CTE administrator if you do not know which port to use.
Step 5 If the computer on which Design Studio is installed is connected to the CTE through a proxy server, click Use Proxy and enter the host and port for HTTP and HTTPS connections.
Step 6 Click OK.
If you cannot connect to the CTE, verify that your computer has a network connection to a running CTE. Contact your CTE administrator for help.
The Design Studio and CTE documentation is available on the Design Studio CD-ROM and is available for downloading from the CTE via the CTE web-based Administration Tool. You can also obtain the documentation from the Cisco home page (http://www.cisco.com) or order a printed copy by calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).
Posted: Mon Aug 18 18:04:03 PDT 2003
All contents are Copyright © 1992--2003 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.