|
|
2 Configure the Cisco CTE 1400
The Cisco Content Transformation Engine (CTE) 1400 handles requests for web pages from devices such as Cisco IP phones, wireless phones, and personal digital assistants and uses transformation instructions to convert HTML/XML pages into wireless-compatible formats. Transformation instructions are created in the companion PC-based application, Cisco CTE Design Studio.
To set up the CTE, you need the following hardware:
The following steps summarize the installation procedure described in the Cisco CTE 1400 Hardware Installation Guide.
Step 2 Connect a null-modem cable to the 9-pin serial port on the back of the CTE and connect the cable to a second computer capable of running terminal emulation software.
Step 3 On the second computer, start a terminal emulation application. For example, start HyperTerminal.
Step 4 Set the serial connection to 9600 bits per second, 8 data bits, no parity, 1 stop bit; set the Backspace key to issue a Delete character.
Hardware flow control is optional.
Step 5 Power up the CTE.
The CTE console appears on the serial console of the second computer.
You are now ready to configure the CTE with your network.
Typical network configurations for a CTE are summarized below.
This section summarizes the procedures for configuring two CTEs with a server load balancer. For detailed information on this and other configurations, see the Cisco CTE 1400 Configuration Note.
Figure 1 shows the network configuration for this procedure. The steps assume that you are adding the CTEs to a network that already has a server load balancer and web server farm.
To configure a CTE with a server load balancer, perform these general steps:
Step 2 On the computer where the CTE console is running, type 2 (Set Networking Parameters), press Enter, and answer the prompts as follows:
Step 3 Type 5 (Set Default Web-Server/Web-Page), press Enter, and enter a virtual IP address for the web server or a URL for the CTE start page (such as a portal page).
Step 4 Type 4 (Set Masquerade Host), press Enter, and enter an IP address for Network Address Translation.
Step 5 If you are using DNS, type 3 (Set DNS Parameter), press Enter, and enter the IP addresses.
Step 6 Type 7 (Set Username and Password), press Enter, and specify a username and password for a Design Studio user. Repeat this step for each Design Studio user.
Step 7 Type 31 (Review and Commit Changes), press Enter, and enter yes to the prompt.
Next, you will configure the server load balancer. The commands in the following procedure are based on the sample configuration shown in Figure 1.
To configure the server load balancer, perform these general steps:
Step 2 Create links between the CTE ports and the server load balancer by adding VLAN2 and VLAN3, and defining the interfaces to the VLANs.
In the sample configuration, the e1 and e2 ports are the interfaces for VLAN2; e3 and e4 are the interfaces for VLAN3.
Step 3 Specify the IP addresses for the VLAN circuits.
In the sample configuration, the IP address for the VLAN2 circuit is 192.168.2.254. The IP address for the VLAN3 circuit is 192.168.3.254.
Step 4 Create services to identify the two CTEs.
In the sample configuration, the IP address for the CTE1 service is 192.168.2.1. The IP address for the CTE2 service is 192.168.2.2.
Step 5 Create an owner so that you can define content rules for the CTE1 and CTE2 services.
Step 6 Create a Layer 3 content rule for the services.
In the sample configuration, the content rule is configured with the virtual IP address 192.168.3.252 and is added to the CTE1 and CTE2 services.
Design Studio is the application used to create the rules that transform website content for delivery to wireless devices and Cisco IP phones.
Design Studio requires the following:
To install Design Studio, perform these steps:
Step 2 If JRE 1.2.2 is not already installed on your computer, install it.
Step 3 Insert the Design Studio CD-ROM into your CD-ROM drive.
If auto-start is enabled on your computer, the installer starts.
If auto-start is not enabled on your computer, double-click the drive icon for your CD-ROM, and then double-click setup.exe.
Step 4 Follow the instructions in the installer.
By default, Design Studio is installed in C:\Programs\Cisco\Cisco CTE 1400 Design Studio.
Step 5 Follow the instructions in Chapter 2 of the Design Studio User Guide to install and configure the wireless device simulators used to preview and test your work in Design Studio.
See the Design Studio User Guide for detailed information on using Design Studio to create, preview, and publish transformation rules. That information is also available from the Design Studio Help menu.
To start Design Studio, you need the following login information from the administrator who set up the Cisco CTE 1400:
To start Design Studio, perform these steps:
Step 2 Enter your username and password.
Step 3 Enter the IP address of the Cisco CTE 1400 you want to use.
Step 4 If necessary, change the upload port number.
The default upload port number is 9001. You might need to change the port number if your firewall redirects ports. Contact your CTE administrator if you do not know which port to use.
Step 5 Click OK.
If you cannot connect to a Cisco CTE 1400, verify that your computer has a network connection to a running Cisco CTE 1400. Contact your CTE administrator for help.
Posted: Mon Aug 18 17:21:53 PDT 2003
All contents are Copyright © 1992--2003 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
