cc/td/doc/product/wanbu/igx8400/8_5
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

System Specifications

System Specifications

This appendix contains system specifications for all models of the IGX node.

General IGX 8410 Specifications

This section provides general system information on the IGX 8410.

System Capacity:

1 shelf with 8 card slots.
Has 2 dedicated front slots for NPMs.
Has 2 dedicated back slots for SCMs (1 slot with blank plate).
Up to 48 physical lines for UNI or NNI.
Up to 8 physical lines for trunks.

Enclosure Size:

IGX 8410 Standalone/Rackmount:
Height: 25 ins. (63.5 cm) standalone; 24.5 ins. (62.3 cm), rack
Width: 19.9 ins. (50.5 cm), standalone; 19 ins. (48.3 cm.), rack
Depth: 26.5 ins. (67.3 cm), standalone and rack-mount

Shipping Weight:

270 pounds (122.7 kilograms)

Clearance Requirement:

Min. clearance: 30 inches front; nominal 30 ins. rear; 12 ins. side.

Power Input Voltage:

AC system: Normal operating range is 100-240 VAC, 47 to 63 Hz. The (under and over-voltage limits are 90-264 VAC).
DC system: -42 to -56 VDC.
Each AC supply can provide up to 400 watts to the card shelves. Space is available for 4 power supplies.

Input AC Power
Connector:

IEC 16 Amp input connector. Six different power cords are available to comply with the standards of individual countries. Power cords are 6 feet (about 2 meters) long. See appendix titled Cabling Summary in the Cisco IGX 8400 Series Installation publication for details.

Current Requirements:

Configuration-dependent: use Network Design Tool for exact requirements. For planning purposes, use the following:

♦ AC System

10 Amps maximum for 110 VAC, 5 A for 220 VAC.

♦ DC System

20 Amps maximum at -48 VDC; 25 Amps at -42 VDC (worst case).

DC Input Connections:

3-wire pluggable terminal block with screw terminal connectors.

Operating Environment:

0º to 40º C (32º to 104º F) normal operation (50º C up to 72 hours). Maximum 85% relative humidity.

Shock:

Withstands 10 G, 10 ms. at 1/2 sine wave.

Vibration:

Withstands 1/4 G, 20-500 Hz.

Heat Transfer to Room:

IGX 8410: 2720 BTUs max.

General IGX 8420 and IGX 8430 Specifications

System Capacity:

1 or 2 shelves, each with 16 card slots.
Requires 1 or 2 dedicated front slot(s) for NPMs.
Requires 1 dedicated back slot for SCM.
Up to 48 physical lines for UNI or NNI.
Up to 16 physical lines trunks.

Enclosure Size:

IGX 8420 Standalone/Rackmount:
HT: 32.25 ins. (82 cm.), standalone; 31.75 ins. (80.7 cm.), rack
WD: 19.9 inches (50.5 cm), standalone; 19 inches (48.3 cm.), rack
DP: 26.75 inches (68 cm), standalone; 26 inches (66 cm.), rack

IGX 8430 Standalone/Rackmount:
HT: 55.5 inches (141 cm.), standalone, 55 inches (139.7 cm) rack
WD: 19.9 inches (50.5 cm), standalone; 19 inches (48.3 cm.), rack
DP: 26.75 inches (68 cm), standalone; 26 inches (66 cm.), rack

Shipping Weight:

600 pounds (270 kilograms) for a fully loaded IGX 8430 enclosure.
400 pounds (180 kilograms) for a fully loaded IGX 8420 enclosure.

Clearance Requirement:

Min. 30 inches front and rear; nominal 12-inch side clearance.

Power Input Voltage:

AC system: Normal operating range is 200-240 VAC, 47 to 63 Hz. The under and over-voltage range is 180-264 VAC.
DC system: -42 to -56 VDC.
Each AC supply can provide up to 875 watts to a card shelf. Cabinet has space for 6 AC power supplies.

Current Requirements:

Configuration-dependent: use Network Design Tool for exact requirements. For planning purposes, use the following:

♦ AC System

IGX 8420 or IGX 8430 node: 12 Amps at a nominal voltage of 200 VAC. At the under-voltage limit of 180 VAC, the current draw is 16 Amps max.

♦ DC System

IGX 8420 node: 24 Amps max. per circuit at -42 VDC (worst case)

IGX 8430 node: 44 Amps at nominal -48 VDC; 50 Amps at -42 VDC maximum per circuit at -42 VDC.

Input AC Power
Connector:

AC Power Distribution unit is the same for all cabinets: IEC 16 Amp input connector. Six different power cords available, depending on country of destination. See appendix titled "Cabling Summary," In the Cisco IGX 8400 Series Installation publication

DC Input Connections:

DC power is the same for all IGX 8420 or IGX 8430 cabinets shipped.
DC: 3-screw pluggable terminal connectors.

Operating Environment:

0º to 40º C (32º F to 104º F) normal operation (50º C or 122º F up to 72 hours). Maximum 85% relative humidity.

Shock:

Withstands 10 G, 10 ms. at 1/2 sine wave.

Vibration:

Withstands 1/4 G, 20-500 Hz.

Heat Transfer to Room:

IGX 8420: 4300 BTUs max, AC-powered system. 3600 BTUs in a DC-powered unit.
IGX 8430: 8600 BTUs max, AC-powered system. 6800 BTUs in a DC-powered unit.

Voice Circuit Support

Voice Channel Interface:

24-channel T1 (D4 format).
24-channel T1-ESF.
30-channel framed CEPT E1.

Voice Compression:

32/24/16 Kbps ADPCM on the CVM
32/24/16 Kbps ADPCM
16 Kbps LDCELP (UVM only)
Voice Activity Detection (VAD) compression

Compression Algorithm:

ITU-T G.721, G.723, G.726.
Cisco 32 Kbps ADPCM
Cisco LDCELP

PCM Encoding Types:

Accommodates µ-Law or A-Law encoding,
End-to-end conversion available.

Channel Gain Control:

-8 dB to +6 dB.

Signalling Modes:

T1: Robbed bit or CCS (ISDN).
E1 and J1: Channel Associative Signalling (CAS) or Common Channel Signalling (CCS).

Signalling Conditioning:

Various make-busy and forced-idle routines during circuit alarm, configurable on a per-channel basis.

Quantizing Distortion Added:

2.5 Quantizing Distortion Units (QDU)s with 32 Kbps ADPCM over 1 hop plus 0.7 QDUs with Digital Loss PAD (µ-law or A-Law).

Nominal Transmission Loss:

0 dB at 1 Khz.

Data Channel Support

Sync. Data Interfaces:

EIA/TIA-232C/D, EIA/TIA-449/422, V.24, X.21, and V.35
with IGX switch as DCE or DTE.

High-Speed Data Rates (HDM):

2.4 Kbps to 1.344 Mbps.

Low-Speed Data Rates:

2.4 to 19.2 Kbps per LDM port.

Ports per card:

LDI: 4 or 8.
SDI: 4.

Control Leads Supported:

SDI: Per interface standards.
SDI: Up to 7 in each direction for fast EIA.
LDI: 3 in each direction for DCE and DTE for each port.

Control Lead Sync
w/Data:

Control leads are sampled every 50 ms. A change normally follows data within 100 to 1000 msec. Fast EIA lead is within 1 byte.

Data Clocking:

Synchronous and isochronous clocking.
Normal, looped, and split clock configurations.

Pleisochronous
Clock Range:

± 2 percent of nominal data rate.

T1 Interface on Frame Relay Interface (FRI) Back Card

Line Rate:

1.544 Mbps, ± 50 bps (± 200 bps VCO lock range).

Line Code:

Bipolar AMI or B8ZS.

Framing Formats:

Fractional T1, adjacent or alternating channels.
Minimum of four DS0 channels required.

Signal Level:

DSX-1 compatible.

Line Impedance:

Terminated=100 Ohms nominal. Bridged=1 KOhm.

Pulse Amplitude

Individual pulse amplitude 2.4 V-3.6 V (making a total base-to-peak amplitude of 6 V ± 0.6V)

Minimum Pulse Density:

Zero code suppression, either LSB, MSB or B8ZS.

Frame Format:

D4 and Extended Superframe (ESF).

VF Signalling:

Robbed bit D4 with A and B bits.

Max. Line Lengths:

Up to 533 feet with equalizers using ABAM cable.

Jitter Transfer:

Meets AT&T PUB 62411 specifications.

Jitter Tolerance:

Meets ANSI standards and AT&T PUB 62411 specs.

Connector:

DB 15 female.

T1 Interface on UFI-8T1

The following applies to each individual T1 line on the UFI-8T1:

Line Rate:

1.544 Mbps, ± 50 bps (± 200 bps VCO lock range).

Line Framing:

ESF per AT&T TR 54016.

Frame Relay Interface:

Meets ANSI T1.618, two-octet header.

Frame Relay Interface Rates:

Either 56 Kbps or n x 64 Kbps, where 1<=n<=24.
Sum of all n<=24.

Number of Frame Relay Interfaces:

1-24 occupied channels where 1<= n<= 24, and the sum of
all n<=24.

Synchronization:

Transmitter can be either loop-timed to receiver or synchronized to shelf (normal mode).

Line Code:

Bipolar AMI or B8ZS.

Framing Formats:

Fractional T1, contiguous DS0s/timeslots.
Minimum of four DS0 channels required.

Signal Level:

DSX-1 compatible.

Line Impedance:

Terminated=100 Ohms nominal. Bridged=1 KOhm.

Pulse Amplitude:

Individual pulse amplitude 2.4 V-3.6 V (making a total base-to-peak amplitude of 6 V ± 0.6V).

Minimum Pulse Density:

Zero code suppression, either LSB, MSB or B8ZS.

Max. Line Lengths:

Up to 533 feet with equalizers using ABAM cable.

Input Jitter Tolerance:

Meets AT&T PUB 62411 specifications.

Output Jitter Tolerance:

Meets AT&T PUB 62411 specifications using normal mode synchronization.

Connector:

DB 15 female.

E1 Interface on BC-E1

Line Rate:

2.048 Mbps, ± 50 ppm (± 200 bps VCO lock range)

Line Code:

Bipolar AMI or HDB3

Line Impedance:

120 Ohms (balanced) or 75 Ohms (balanced or unbalanced)

Minimum Pulse Density:

Zero code suppression via HDB3 coding

Frame Format:

Unframed, 32-channel (G.703). Framed: 30 or 31-channel CEPT multiframe per ITU-T G.704.

VF Signalling:

CAS or CCS

Max. Line Lengths:

100 meters. The E1 output complies with G.703, so cabling must not exceed -6dB/1000 feet at 1024 kHz (applies to 75-Ohm coax or 120-Ohm twisted pair up to 350 meters or 1000 feet). Cisco supplies cable with a maximum attenuation of 7 dB /1000 ft., but the maximum cable length for this E1 interface is 100 meters.

Jitter:

Transmit output jitter, receive jitter tolerance, and jitter gain meet G.823.

Electrical Interface:

Complies with G.703 Specification.

Connector:

DB 15 female or BNC.

E1 Interface for UFI-8E1

The following applies to each individual E1 line on the UFI-8E1:

Line Interface Connector:

DB15 (120 Ohms), BNC (75 Ohms)

Line Rate:

2.048 Mbps, ±50 bps (±200 bps VCO lock range).

Frame Relay Interface:

Meets ANSI T1.618, two-octet header.

Number of Frame Relay Interfaces:

1-31 occupied channels where 1 <= n <= 31, and the sum of all
n <= 31

Frame Relay Interface Rate:

Either 56 Kbps or n x 64 Kbps, where 1 <= n <= 31. Sum of all
n <= 31.

Line Code:

Bipolar AMI or HDB3.

Line Impedance:

120 ohms (balanced) or 75 ohms, balanced or unbalanced.

Minimum Pulse Density:

Zero code suppression via HDB3 coding.

Frame Format:

Unframed, 32-channel (G.703). Framed: 30 or 31-channel CEPT multiframe per ITU-T G.704.

Max. Line Lengths:

E1 output complies with G.703, so cabling must not exceed -6dB/1000 feet at 1024 kHz (applies to 75-ohm coax or 120-ohm twisted pair up to 350 meters or 1000 feet).

Input Jitter Tolerance:

Meets G.823.

Output Jitter Tolerance:

Meets G.823.

Electrical Interface:

Complies with G.703 Specification.

Connector:

Back card has either all DB15 female or all BNC connectors.

E2 Interface on BTM

Required Hardware:

AIT front card on the IPX, BTM front card on the IGX. The back card is the AIT-E2

Line Rate:

8.448 Mbps

Line Coding:

HDB3.

Cell Delineation:

HEC

Physical Medium;

Coaxial

Line Length:

50 feet maximum; 6 feet nominal

Connector:

BNC, 75 Ohms.

Synchronization:

Master/slave (NOTE: loop timing to IPX or IGX node is allowed.)

Interfaces per card:

One

Applicable Standards:

E2 specification and G.703.

HSSI Interface on BTM

Required Hardware:

AIT front card on the IPX or BTM front card on the IGX node. The back card is the AIT-HSSI.

Line Rate:

Presettable, programmable for the range 4-50.84 Mbps: increments depend on the attached DSU.

Line Coding:

NRZ.

Cell Delineation:

PLCP

Physical Medium:

Multi-conductor, 25 twisted pairs in a ribbon cable, 110 Ohms.

Line Length:

50 feet maximum; 6 feet nominal

Connector:

50-pin, 50 mil SCSI type.

Synchronization:

None—accepts DSU clocks

Interfaces per card:

Single port.

Applicable Standards:

High Speed Serial Interface specification, March, 1990

I.432, G.804.

T3 Interface on BC-UAI-1T3

Line Rate:

44.736 Mbps ± 20 ppm, asynchronous.

Line Code:

B3ZS.

Clock Source Mode:

Internal (Asynchronous).

Signal Level:

DSX-3.

Framing Formats:

M13 mode, C-bit parity.

Alarms Processed:

AIS.
LOS.
Remote Alarm Indication.
Loss Of Framing.

Line Errors Counted:

BPV.
Parity Bit Errors.

Receiver Input Impedance:

Terminated=75 ohms.

Transmission Modes:

Point-to-Point.

Jitter:

Meets ACCUNET T45 specification (Pub 54014).

Connector:

75 ohm BNC.

Max. Line Lengths:

450 ft. (137 m.) to DSX-3 using 75 Ohm coaxial cable.

Indicators:

RED Alarm.
YELLOW Alarm.
LOS.
AIS.

E3 Interface BC-UAI-1E3

Line Rate:

34.368 Mbps ± 20 ppm, asynchronous.

Line Code:

HDB3.

Clock Source Mode:

Internal (Asynchronous).

Signal Level:

ITU-T G.703

Framing Formats:

ITU-T G.804, G.832,

Alarms Processed:

AIS.
LOS.
Remote Alarm Indication.
Loss Of Framing.

Line Errors Counted:

BPV.
Parity Bit Errors.

Receiver Input Impedance:

75 ohms unbalanced.

Transmission Modes:

Point-to-Point.

Jitter:

Per ITU-T G.823.

Connector:

75 ohm BNC.

Maximum Line Lengths:

137 meters (450 ft.) using specified cable.

Indicators:

RED Alarm.
YELLOW Alarm.
LOS.
AIS.

J1 Interface on the BC-UVI-2J1EC

Line Rate:

2.048 Mbps, ± 50 ppm (± 200 bps VCO lock range)

Line Code:

Bipolar CMI

Line Impedance:

120 Ohms (balanced)

Frame Format:

Per JJ-20.11

VF Signalling:

CAS or CCS

Max. Line Lengths:

100 meters. Cisco supplies cable with a maximum attenuation of
7 dB /1000 ft., but the maximum cable length recommended for this J1 interface is 100 meters.

Jitter:

Transmit output jitter, receive jitter tolerance, and jitter gain meet G.823.

Electrical Interface:

Complies with G.703 Specification.

Connector:

Two DB 15, female.

J1 Interface on the BC-J1

Line Rate:

2.048 Mbps, ± 50 ppm (± 200 bps VCO lock range)

Line Code:

Bipolar CMI

Line Impedance:

120 Ohms (balanced) or 75 Ohms (balanced or unbalanced)

Frame Format:

Per JJ-20.11

VF Signalling:

CAS or CCS

Max. Line Lengths:

100 meters. Cisco supplies cable with a maximum attenuation of 7 dB /1000 ft., but the maximum cable length recommended for this J1 interface is 100 meters.

Jitter:

Transmit output jitter, receive jitter tolerance, and jitter gain meet G.823.

Electrical Interface:

Complies with G.703 Specification.

Connector:

DB 15 female or BNC.

Frame Relay Interface for the FRM Front Card

Type of Service:

Permanent Virtual Circuit (PVC).

Data Interface:

Per ITU-T I.122 and ANSI T1/S1 Standards.

Data Transfer Protocol:

LAP-D frame level core functions.

Input Data Format:

High Level Data Link (HDLC) protocol.

Input Data Frame Length:

Up to 4096 bytes.

Frame Integrity Check:

Frame Check Sequence and CRC check of data frame. If CRC fails, data frame is discarded at receiving node.

Input Data Rate:

56 Kbps-2.048 Mbps. The maximum rate is available with only one of four ports on the back card active).

Ports per Card:

4 Model D

31 Model E

PVCs per Port:

252 per FRM card, distributed in any combination.

Port Electrical Interface:

ITU-T V.35. IGX and X.21 can act as a DCE or DTE for direction of control leads and timing on Model D and E using E1 or T1.

Data Clocking:

Normal or looped.

Virtual Circuit Identifier:

Data Link Connection Identifier (DLCI).

Control Protocol:

Local Management Interface with XON/XOFF type flow control. The IGX node sets FECN and BECN bits in frame relay frame.

Bundled Connections:

252 virtual circuits per card
1024 virtual circuits per node.

Billing Time Accuracy:

Upon request from a user-device, the IGX node provides GMT from any node accurate to within 1 second.

ATM Interface

Type of Service:

Permanent Virtual Circuit (PVC)

Interface Types:

User-to-Network (UNI) and Network-to-Network (NNI) per ITU I.361 and I.363

Data Rates:

T1, E1, T3, E3

ATM Layer:

Physical Layer Convergence Protocol per AT&T publication TA-TSY-00772 and 000773 for T3; ITU I-361 with HEC for E3

Cell Rate:

96,000 cells/sec. for T3, 80,000 cells/sec. for E3

Adaptation Layer:

AAL5

Number of PVCs per card:

255

VPI Addressing Range:

0-255

VCI Addressing Range:

0-65535

Traffic Queues:

CBR, VBR, and ABR

Management Protocol:

Layer Management Interface (LMI) and Interim Layer Management Interface (ILMI)

Network Synchronization

External Clock Sources:

The IGX switch synchronizes to the nearest, highest-stratm clock available. Any T1, E1, T3, E3 line, trunk, or optional external clock input can serve a clock source.

Internal to Node Source:

T1: 1.544 MHz, ± 10 ppm. (Stratum 4).
E1: 2.048 MHz, ± 10 ppm (Stratum 4).

Clocking Hierarchy:

Dynamic primary, secondary, and tertiary clocking.

Network Management Control

Network Control Terminal:

StrataView Plus workstation and software required for graphical display of network status, statistics gathering and display, and automatic downloading of software.

Control Terminal:

DEC VT100, WYSE 85, Televideo 970 or equivalent terminal for basic system configuring and alarm monitoring.

Remote Alarm Reporting:

Auto-dial modem connects to one of two control ports on each IGX node for automatic reporting of network alarms.

Remote Diagnostics:

Auto-answer modem connects to one of two control ports on each IGX node for remote diagnostic access by Cisco TAC or other authorized personnel.

Network Control Ports:

Two ports per node, (one EIA/TIA 232C interface and one Ethernet LAN port).

Alarm Notification:

Status of all trunks and nodes in network distributed to and stored by each individual node. Reported to StrataView Plus workstation at connecting node.

External Alarms:

Meets Bellcore Compatibility Bulletin #143 and AT&T Technical Reference PUB 43801 DS1 (T1) facility alarm requirements when equipped with DTI group.

Indicators and Controls:

Active and Fail lights on all cards and power supplies.


hometocprevnextglossaryfeedbacksearchhelp
Posted: Wed Sep 11 14:04:51 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.