cc/td/doc/product/wanbu/bpx8600/9_3_0
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Managing the Network

Managing the Network

This chapter tells you how to use network administration commands. Examples of the tasks these commands perform are creating a password, setting the network date and time, and adding a user.

Signing On to the System

Signing on to a node is a two-step process that requires you to enter a User ID and a password. The system or network administrator can provide a User ID and password to you. The User ID can be up to 12 characters. To protect the security of the system, you should change your password regularly. Only your system administrator can change the User ID. To sign on to a node:


Step 1   Enter your user ID at the system prompt "Enter User ID."

Step 2   Enter your password at the "Enter Password" prompt. For initial sign-on, enter the password that the system administrator provides. You can change the password with the cnfpwd command.

After you sign on, the system is ready and so prompts you for the next command.


Signing Off the System

When you have completed a session and want to sign off, use the bye command. This command returns the display to the initial system sign-on prompt. If you enter the bye command when you have a virtual terminal connection to another node, the bye command ends the virtual terminal session and returns to the local session. To end the local session and thus sign-off the system, again enter the bye command.

Changing a Password

To change the password given to you by your System Administrator, or to change your present password to a different one, perform the following. To ensure the security of your system, your password should be changed on a regular basis. See the System Administrator for the recommended frequency of change.


Step 1   Enter the cnfpwd command. The system prompts for your current password.

Step 2   Enter your current password. The system prompts for a new password.

Step 3   Enter a new password. Passwords must have 6-15 characters. The system prompts you to confirm the new password by typing it again.


Set Date and Time

Date and time are network-wide parameters. You can set the time zone for each node. The cnfdate command lets you set both time and date. The cnftime command lets you set the time for the entire network.

Summary of Commands

Table 13-1 shows the full name and starting page for the description of each network management command.


Table 13-1:
Commands for Managing a Network
Command Description Page

adduser

Add user(s)

13-4

cnfpwd

Configure password

13-6

cnffwswinit

Configure Cisco WAN Manager node IP address firmware/software initiator

13-7

cnfsnmp

Configure SNMP parameters

13-8

cnfstatmast

Configure statistics master SV+ address

13-9

cnfsysparm

Configure system parameters

13-10

deluser

Delete user

13-15

dsplanip

Display LAN IP address of all nodes in network

13-16

dspnwip

Display network IP interface

13-18

dsppwd

Display password

13-19

dspsnmp

Display SNMP parameters

13-21

dspsnmpstats

Display SNMP statistics

13-23

dspsv3

Display WAN Manager Layer 3 Link Control Blocks

13-25

dspusers

Display users

13-25

dspusertask

Display user task

13-34

dspusertasks

Display all user tasks

13-37

adduser

Adds a user to the network. The first time the new user ID is used for logon, a prompt appears asking the user to change from the default password to a new password which they enter using the cnfpwd command. Users with privilege levels 1 through 5 may add users with lower privilege levels. Since privilege level 6 has no user levels below it, level 6 cannot add any users.

Full Name

Add a user

Syntax

adduser <user_id> <privilege_level>

Related Commands

cnfpwd, deluser, dspusers

Attributes

Privilege Jobs Log Node Lock

1-5

No

Yes

IGX, BPX

Yes

Example 1

adduser sarah 5

Description

Add a user sarah with privilege level 5.

System Response
alpha TRM YourID:1 IGX 8410 9.2 Aug. 16 1998 13:48 PST YourID 1 Sarah 5 Last Command: adduser Sarah 5 Next Command:


Table 13-2: adduser—Parameters
Parameter Description

userid

Specifies the name of the user to add.

privilege level

Specifies the privilege level to grant to the added user. The range of levels is 1-6, where 1 is the highest level and 6 is the lowest.

cnfpwd

Changes the password associated with a User ID. To change a password, you must log into the node with the User ID whose password you want to change. Passwords are case-sensitive.

In a structured network, each domain requires you to have a password. In each domain, your password and associated privilege level can be the same as or different from those in the other domains. For each domain, you can change the password at any node within the domain, including a junction node.

Full Name

Configure password

Syntax

cnfpwd <old password> <new password>

Related Commands

dsppwd, adduser, deluser, dspusers

Attributes

Privilege Jobs Log Node Lock

1-6

No

Yes

IGX, BPX

Yes

Example 1

cnfpwd

Description

Change your password.


Table 13-3: cnfpwd—Parameters
Parameter Description

old password

Specifies the old password.

new password

Specifies the new password. Passwords must have 6-15 characters. Only letters, numbers, "_", and "-" are allowed in a password. Spaces are not allowed.

cnffwswinit

Use the cnffwswinit command to inform the IGX/BPX the IP address of the machine used to initiate a firmware or software download. This is used as a sort of a safety measure, to prevent downloads from being started anywhere in the network. You must have access to a node, and use the cnffwswinit command to set the IP address before a download will be accepted from that address.

Full Name

Configure firmware and software downloader's WAN Manager IP address

Syntax

cnffwswinit <IP address of download initiator>

Related Commands

dsppwd, adduser, deluser, dspusers

Attributes

Privilege Jobs Log Node Lock

1-6

No

Yes

IGX, BPX

Yes

Example

cnffwswinit 172.29.52.17

Description

Configures the IP address of the machine running WAN Manager from which the firmware and software download will be initiated to other nodes. If you do not provide the IP address for the WAN Manager node from which to initiate the firmware/software download, you will be prompted to enter it.


Table 13-4: cnffwswinit-Parameters
Parameter Description

IP address

Specifies IP address of machine running WAN Manager from which the firmware and software download will be initiated to other nodes in the network.

cnfsnmp

Configures the SNMP GET and SET community strings.

Full Name

Configure SNMP parameters

Syntax

cnfsnmp <GET community string> <SET community string>

Related Commands

dspsnmp, dspsnmpstats

Attributes

Privilege Jobs Log Node Lock

1-6

No

Yes

IGX, BPX

Yes

Example 1

cnfsnmp

Description

Configure the SNMP GET and SET community string parameters.


Table 13-5: cnfsnmp—Parameters
Parameter Description

get community string

Specifies the GET community string.

set community string

Specifies the SET community string.

cnfstatmast

Configures an IP address for the Statistics Master process in WAN Manager. The cnfstatmast command defines the IP address for routing the messages to and from the Statistics Master in WAN Manager.

The Statistics Master process requests and receives network statistics by using TFTP Get and Put messages. These TFTP messages pass between the node and the Statistics Master over IP Relay. See the cnfnwip description for details on setting a node address.

Full Name

Configure statistics master SV+ address

Syntax

cnfstatmast <IP Address>

Related Commands

cnfnwip, dspnwip

Attributes

Privilege Jobs Log Node Lock

1

Yes

Yes

IGX, BPX

Yes

Example 1

cnfstatmast 199.35.96.217

Description

Configure 199.35.96.217 as the IP address for the Statistics Master.


Table 13-6: cnfstatmast—Parameters
Parameter Description

ip address

Specifies the IP address for the Statistics Master. IP addresses have 32-bits. The format of an IP address is x.x.x.x, where x is a value in the range 1-255.

cnfsysparm

Configures various system (or network) parameters. Network-wide parameters are configurable only when all nodes in the network are reachable. The parameters you specify with this command apply throughout the network regardless of which node you execute the command from. Take special note of the consequences of how you resolve conflicting values when networks are joined.

You can select each parameter by its index number. The paragraphs that follow describe each parameter by index number. Table 13-6 lists the defaults and ranges for each parameter.


Note   Using cnfsysparm requires caution because network rerouting or loss of data may result from changes in system parameters. If necessary, consult with the TAC before you use cnfsysparm.

The following paragraphs describe the user-configurable system parameters by index number.


Table 13-7: Defaults and Ranges of cnfsysparm Parameters
System Parameters
Index System-Wide Parameter Default Range

1

Max Time Stamped Packet Age (in milliseconds).

40

1-60

2

Fail Connections On Communication Break.

No

y or n

3

Max Network Delay for "v" connections (in milliseconds).

14

1-255

4

Max Network Delay for "c" connections (in milliseconds).

27

1-64

5

Max Network Delay for "d" connections (in milliseconds).

14

1-255

6

Max Network Delay for "a" connections (in milliseconds).

27

1-255

7

Max Network Delay for High-Speed Data connections (in milliseconds).

40

1-255

8

Max Network Delay for CDP or CVM to CDP or CVM "v" connections (in milliseconds).

64

1-255

9

Max Network Delay for CDP or CVM to CDP or CVM "c" connections (in milliseconds).

64

1-64

10

Max Network Delay for CDP or CVM to CDP or CVM "t & p" connections (in milliseconds).

64

1-255

11

Max Network Delay for CDP or CVM to CDP or CVM "a" connections (in milliseconds).

64

1-255

12

Max Network Delay for CDP or CVM to CDP or CVM High-Speed Data connections (in milliseconds).

64

1-255

13

Enable Discard Eligibility (DE).

No

y or n

14

Use Frame Relay standard parameters Bc and Be.

No

y or n

15

Obsolete: Max Local Delay for Interdom CDP to CDP "v" connections.

27

1-255

16

Obsolete: Max Local Delay for Interdom CDP to CDP "c" connections.

27

1-64

17

Obsolete: Max Local Delay for Interdom CDP to CDP "t & p" connections.

27

1-255

18

Obsolete: Max Local Delay for Interdom CDP to CDP "a" connections.

27

1-255

19

Obsolete: Max Local Delay for Interdom CDP to CDP High-Speed Data connections.

27

1-255

20

Obsolete: Max Local Delay for Interdom High-Speed Data connections (in milliseconds).

28

1-255

21

FastPAD Dejitter Buffer Depth (in milliseconds).

15

0-255

22

Number of Consecutive Invalid Login Attempts to Cause Major Alarm.

0

3-9

23

Enable Connection Deroute Delay.

Yes

y or n

24

Frame Relay VCs Polling Rate is the number of minutes between polling cycles for both ATM and Frame Relay virtual connections in the network.

5

5, 10, or 15

25

Port Polling Rate is the number of minutes between polling cycles for interval statistics gathered for all ports in the network.

5

5, 10, or 15

Full Name

Configure system parameters

Syntax

cnfsysparm <index> <value>

Related Commands

none

Attributes

Privilege Jobs Log Node Lock

1

Yes

Yes

IGX, BPX

Yes

Example 1

cnfsysparm

Description

Configure system-wide parameters. In response to the prompt "Continue" at the bottom of the display enter a "y", or press Return to display the second screen, or enter "n" to not display the next screen. If you enter an "n," the prompt line requests an index number.

System Response
sw171 VT SuperUser IGX 8420 9.2 Oct. 14 1998 17:37 GMT System-Wide Parameters 1 Max Time Stamped Packet Age (msec) ................................ 32 2 Fail Connections On Communication Break ........................... No 3 Max Network Delay for 'v' connections (msec)....................... 14 4 Max Network Delay for 'c' connections (msec)....................... 27 5 Max Network Delay for 't' & 'p' connections (msec)................. 14 6 Max Network Delay for 'a' connections (msec)....................... 27 7 Max Network Delay for High Speed Data connections (msec)........... 32 8 Max Network Delay for CDP-CDP 'v' connections (msec)............... 32 9 Max Network Delay for CDP-CDP 'c' connections (msec)............... 32 10 Max Network Delay for CDP-CDP 't' & 'p' connections (msec)......... 32 11 Max Network Delay for CDP-CDP 'a' connections (msec).............. 32 This Command: cnfsysparm Continue? n
System Response

In response to the "Continue" prompt at the bottom of the display, enter an "n," then enter a "1" to enter the maximum allowable age for a time-stamped packet.

sw171 VT SuperUser IGX 8420 9.2 Oct. 14 1998 17:37 GMT System-Wide Parameters 1 Max Time Stamped Packet Age (msec) ................................ 40 2 Fail Connections On Communication Break ........................... No 3 Max Network Delay for 'v' connections (msec)....................... 14 4 Max Network Delay for 'c' connections (msec)....................... 27 5 Max Network Delay for 't' & 'p' connections (msec)................. 14 6 Max Network Delay for 'a' connections (msec)....................... 27 7 Max Network Delay for High Speed Data connections (msec)........... 32 8 Max Network Delay for CDP-CDP 'v' connections (msec)............... 32 9 Max Network Delay for CDP-CDP 'c' connections (msec)............... 32 10 Max Network Delay for CDP-CDP 't' & 'p' connections (msec)......... 32 11 Max Network Delay for CDP-CDP 'a' connections (msec).............. 32 This Command: cnfsysparm 1 Enter new value (in Decimal):

Enter the number of the parameter you wish to change, along with the value. For example, to change the Maximum Time-Stamped Packet Age (1) from 40 milliseconds to 42 milliseconds, enter:

1 42


Note   If you change item 15, the following prompt appears on the screen:

Changing this parameter will reset Frame Relay classes to their defaults. Continue (y/n)?

Changing parameter 15 requires a change in the Frame Relay classes. Since Frame Relay classes are not associated with a specific port (or port speed 0), no translation can be made. The values for Bc and Be, or VC Q depth and PIR are reset to their default values.


Table 13-8: cnfsysparm—Parameters
Parameter Description

index

Specifies a numerical value that refers to the specific parameter to be changed. Index numbers and descriptions of the system-wide parameters are in the table that precedes the command summary.

value

Specifies a numerical value that applies to the selected parameter. See Table 13-6.

deluser

Deletes a user from the network. A user can delete users at any lower privilege level.

Full Name

Delete a user

Syntax

deluser <user_id>

Related Commands

adduser, dspusers

Attributes

Privilege Jobs Log Node Lock

1-5

No

Yes

IGX, BPX

Yes

Example 1

deluser john

Description

Delete user "john."

alpha TRM YourID:1 IGX 8410 9.2 Aug. 16 1998 13:52 PST YourID 1 Sarah 5 \ Last Command: deluser John Next Command:


Table 13-9: deluser—Parameters
Parameter Description

userid

Specifies the name of the user to delete from the network.

dsplanip

The dsplanip command is similar to the dspnwip command. It displays the LAN IP address and subnet mask of the local node, and also displays the LAN IP address of all other nodes in the network, including feeder nodes. (Feeder nodes are displayed with a blank node name, and they appear immediately beneath the hub node to which they are attached.)

The dsplanip command displays the LAN IP address of all nodes reachable from a given node in the network.

The dsplanip command is new in Release 9.2 in support of the Out-of-Band network management feature which enables management traffic to be sent over IP to the switches' LAN Ethernet interface, thereby reducing the load on trunk bandwidth and node processor times.

Service-Affecting Alarms and Out-of-Band Network Management Features in Release 9.2

The service-affecting alarms feature enhances reporting of switch alarm conditions to Cisco WAN Manager, and to a customer network management system (NMS) through the Cisco WAN Manager RTM Proxy. New Robust Alarm messages are generated from existing switch events that could affect service.

The Out-of-Band network management feature in Release 9.2 enables management traffic to be sent over IP to switches' LAN Ethernet interface to Cisco WAN Manager, thereby reducing the load on trunk bandwidth and node processor times. For WAN Manager to be able to manage a switch out of band, the following things must be done:

To change the LAN IP address of a routing node you use the cnflan user command. The Out-of-Band Network Management software in Release 9.2 detects a change to the LAN IP address on a routing or feeder note and forwards an update message to Cisco WAN Manager.


Note   The service-affecting alarms and out-of-band network management features in Release 9.2 can interoperate in mixed networks containing one or more nodes running switch software Release 9.1 or 8.5.

Full Name

Display LAN IP address of local node, and all nodes in the network

Syntax

dsplanip

Related Commands

dspphyslns, dsptrks

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX

No

Example 1

dsplanip

Description

Display the LAN IP address of local node, and all other reachable nodes in network.

System Response
sw248 TN StrataCom BPX 15 9.2.0 May 4 1998 18:28 GMT Active LAN IP Address: 172.29.9.155 Active LAN IP Subnet Mask: 255.255.255.0 NodeName LAN IP Address sw252 172.29.9.159 172.29.9.175 sw263 172.29.9.167 172.29.9.163 sw8 172.29.9.124 sw248 172.29.9.155 172.29.9.134 172.29.9.173 Last Command: dsplanip

dspnwip

Displays the IP address for each node in the network. The IP address is used to route TFTP messages transferring bulk statistics between the node and the WAN Manager Statistics Master.

Full Name

Display network IP interface

Syntax

dspnwip

Related Commands

cnfwip

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dspnwip

Description

Display network IP addresses.

axiom1 TN bootzilla IGX 32 9.2 Sep. 5 1998 18:18 GMT Active Network IP Address: 169.134.90.106 Active Network IP Subnet Mask: 255.255.255.0 NodeName IP Address axiom1 169.134.90.111 169.134.90.105 169.134.90.101 axiom2 169.134.90.102 axiom3 169.134.90.103 axiom1 169.134.90.106 Last Command: dspnwip Next Command:

dsppwd

Displays the password of the current user or any user at any lower privilege level.

Full Name

Display password

Syntax

dsppwd <user_id>

Related Commands

adduser, cnfpwd, deluser, dspusers

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dsppwd yourid

Description

Display the password for user YourID.

System Response
alpha TRM YourID:1 IGX 8410 9.2 Aug. 16 1998 13:56 PST The password for YourID is liftoff

This Command: dsppwd YourID This screen will self-destruct in ten seconds Next Command: dsppwd YourID


Table 13-10: dsppwd—Parameters
Parameter Description

userid

Specifies the user whose password is displayed.

dspsnmp

Display the following SNMP parameters for the current node:

Full Name

Display SNMP parameters

Syntax

dspsnmp

Related Commands

cnfsnmp, dspsnmpstats

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dspsnmp

Description

Display the SNMP parameters for the current node.

System Response
sw91 TN SuperUser IPX 8 9.2 Aug. 29 1998 13:45 GMT Get Community String: NOACCESS Set Community String: NOACCESS Trap Community String: NOACCESS SNMP Set Request Queue Size: 110 SNMP Queued Request Timeout (secs): 30 SNMP Trap Event Queue Size: 100 Last Command: dspsnmp Next Command:

dspsnmpstats

Displays the following SNMP statistics for the node:

Full Name

Display SNMP parameters

Syntax

dspsnmpstats

Related Commands

cnfsnmp, dspsnmp

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dspsnmpstats

Description

Display SNMP statistics for the current node.

System Response
sw91 TN SuperUser IPX 8 9.2 Aug. 29 1998 13:21 GMT SVC Requests Received: 256 Traps Transmitted: 256 SVC Current Queue Length: 0 TRAP Current Queue Length: 0 SVC Maximum Queue Length: 0 TRAP Maximum Queue Length: 0 SVC Requests Timed Out: 0 TRAP Queue Events Discarded: 196864 Overflow Traps Transmitted: 100925440 Current Trap Managers: 0/10 Snmp_Trap_Db Ptr: 30DDCD02 Last Command: dspsnmpstats Next Command:

dspsv3

Displays the Cisco WAN Manager L3 (Layer 3) Link Control Blocks.

The dspsv3 command displays the LCBs (Link Control Blocks) used by a switch to communicate with one or more SV+ workstations. The display shows whether the out-of-band (lanip) option is being used. Previous to Release 9.2, the dspsv3 screen indicated whether or not NWIP was being used. In Release 9.2, the dspsv3 screen distinguishes between the three modes supported in Release 9.2:

This command supports the Out-of-Band network management feature, which enables management traffic to be sent over IP to switches' LAN Ethernet interface, thereby reducing the load on trunk bandwidth and node processor times.

The dspsv3 command displays counts of pending SONET APS (Automatic Protection Switching) alarms.

Full Name

Display Cisco WAN Manager L3 (Layer 3s) Link Control Blocks

Syntax

dspsv3

or

dspsv3 <LCB number>


Table 13-11: Description of the Fields in the dspsv3 Display
Field Explanation

Serial Admin

Serial link admin window

LAN Admin

LAN Admin window

LCB

Link Control Block number (0 is the gateway link)

Node

SV+ gateway node number (0 is local IO)

IP

IP address (* indicates nwip is enabled)

Related Commands

dsplanip

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

BPX

No

Example 1

dspsv3

Description

Display Cisco WAN Manager L3 Link Control Blocks.

System Response
nsaigx2 TN StrataCom IGX 8420 9.2 June 8 1998 06:11 GMT Number of Active SV3 Links: 2 Serial Admin: None LAN Admin: None LCB: 0 Node: 0 IP:*172.16.64.20 LCB: 1 Node: 3 IP:*172.16.64.20 >Last Command: dspsv3
Example 2

dspsv3

System Response
sw248 TN StrataCom BPX 15 9.2.0 May 4 1998 18:05 GMT Number of Active SV3 Links: 2 Serial Admin: None LAN Admin: None LCB: 0 Node: 128 IP:N172.29.9.29 LCB: 1 Node: 128 IP:L172.29.9.53 LCB: 2 Node: 128 IP: 172.29.9.115 Last Command: dspsv3

In Example 2, the summary display shows three Link 1 LCBs, which connect to three different SV+ workstations. The "N" next to the first IP address indicates the nwip_on option. The "L" next to the second address indicates the lanip option. The absence of a symbol on the third line indicates the nwip_off option.

Example 3

dspsv3

System Response
sw248 TN StrataCom BPX 15 9.1.a5 May 4 1998 18:11 GMT LCB: 1 Alloc: 1 sv3_lcb_ptr: 31514034 IP Address: 172.29.9.53 (lanip) Response Timer: 0 Idle Timer: 393 Retry Count: 120 Current Protocol State: SV3_TRANSFER No. of Buffers in the data_q: 0 No. of Buffers in the xmit_q: 0 No. of Buffers in the nflow_q: 0 Comm Break Alarm: Update: 0, Pending: 0 Comm Break Alarm Bitmaps: Update: 314741FC, Pending: 3147449C Last Command: dspsv3 1

In Example 3, the detailed display below shows the state on an individual link control block. The display indicates the use of the lanip option.


Table 13-12: Description of the Fields in the dspsv3 Display
Field Explanation

Serial Admin

Serial link admin window

LAN Admin

LAN Admin window

LCB

Link Control Block number (0 is the gateway link)

Node

SV+ gateway node number (0 is local IO)

IP

IP address (* indicates nwip is enabled)

Example 1

dspsv3 0

Description

Display Cisco WAN Manager L3 Link Control Blocks.


Table 13-13: Description of the Fields in the Previous dspsv3 Display
Field Explanation

LCB

LCB number

Alloc

LCB allocated (1) or no (0)

sv3_lcb_ptr

Address of LCB in memory

IP Address

SV+ IP Address

Response Timer

SV+ Link Response Timer

Idle Timer

Display SV+ Link Idle Timer

Retry Count

SV+ Link Retry Count

Current Protocol State

Link state (idle, reset, transfer, poll)

No. of buffers in the data_q

Messages in the data queue

No. of buffers in the xmit_q

Messages in the transmit queue

No. of buffers in the nflow_q

Messages in the non-flow-controlled queue

Subscribed applications

Applications to which SV+ has subscribed

Update object(s)

Robust object types that have updated status

Pending

Robust object types that have been updated to SV+, and are waiting for an acknowledgment from SV+.

System Response
nsaigx2 TN StrataCom IGX 8420 9.2 June 8 1998 06:11 GMT LCB: 0 Alloc: 1 sv3_lcb_ptr: 3120248C IP Address: 172.29.9.60 Response Timer: 0 Idle Timer: 600 Retry Count: 120 Current Protocol State: SV3_TRANSFER No. of Buffers in the data_q: 0 No. of Buffers in the xmit_q: 0 No. of Buffers in the nflow_q: 0 This Command: dspsv3 0 Continue? LCB: 0 Alloc: 1 sv3_lcb_ptr: 3120248C Subscribed Applications: Topology MaintLog 312024C0 Update Pending Revision: 0 0 Stats Rebuild: 0 0 Subscription: 0 0 APS Alarm: 0 31202EB6 0 31202EDB Feeder Obj: 0 312029D2 0 312029D4 Feeder Alarm: 0 31202ED8 0 31202EDA Port Obj: 0 312029C6 0 312029CC Port Alarm: 0 31202ECC 0 31202ED2 Conn Obj: 0 312024D0 0 31202741 Conn Alarm: 0 312029D6 0 31202C47 Cline Obj: 0 312029B2 0 312029B7 Cline Alarm: 0 31202EB8 0 31202EBD Trunk Obj: 0 312029BC 0 312029C1 Trunk Alarm: 0 31202EC2 0 31202EC7 Last Command: dspsv3 0 Continue? LCB: 0 Alloc: 1 sv3_lcb_ptr: 3120248C Robust Database Updates data: db_update_flags: 30D6E16C db_pending_flags: 30D6E355 flag_offset_table: 30D6E56C 1:0 2:0 3:0 4:0 5:0 6:0 7:0 8:1 9:16 10:1A 11:59 12:0 13:D6 14:D7 15:0 16:DC 17:FC 18:0 19:13B 20:0 21:17B 22:17D 23:0 24:0 25:17F 26:0 27:180 28:0 29:181 30:183 31:0 32:0 33:0 34:185 35:0 36:0 37:186 38:0 39:0 40:0 41:0 42:0 43:0 44:0 45:0 46:187 47:0 48:0 49:0 50:0 51:18C 52:0 53:0 54:0 55:0 56:0 57:0 58:0 59:0 60:0 61:0 62:0 63:0 64:0 65:0 66:18D 67:0 68:0 69:0 70:0 71:0 72:0 73:18E 74:0 75:0 76:0 77:0 78:0 79:0 80:0 81:0 82:0 83:0 84:0 85:0 86:0 87:0 88:0 89:0 90:0 91:0 92:18F 93:18F 94:190 95:1A5 96:1A9 97:0 98:0 99:1E8 100:0 101:0 102:0 103:0 104:0 Last Command: dspsv3 0 LCB - LCB number Alloc - LCB allocated (1) or not (0) sv3_lcb_ptr - address of LCB in memory IP Address - SV+ IP Address Response Timer - SV+ Link Response Timer Idle Timer - Display SV+ Link Idle Timer Retry Count - SV+ Link Retry Count Current Protocol State - Link state (idle, reset, transfer, poll) No. of Buffers in the data_q - Messages in the data queue No. of Buffers in the xmit_q - Messages in the transmit queue No. of Buffers in the nflow_q- Messages in the non-flow-controlled queue Subscribed Applications - Applications to which SV+ has subscribed Update - Robust object types that have updated object(s) status. Pending - Robust object types that have been updated to SV+, and are waiting for an acknowledge from SV+. Robust database update bitmap addresses.

dsptsmap

Displays the following SNMP statistics for the node:

Full Name

Display SNMP parameters

Syntax

dspsnmpstats

Related Commands

cnfsnmp, dspsnmp

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dspsnmpstats

Description

Display SNMP statistics for the current node.

System Response
sw91 TN SuperUser IPX 8 9.2 Aug. 29 1998 13:21 GMT SVC Requests Received: 256 Traps Transmitted: 256 SVC Current Queue Length: 0 TRAP Current Queue Length: 0 SVC Maximum Queue Length: 0 TRAP Maximum Queue Length: 0 SVC Requests Timed Out: 0 TRAP Queue Events Discarded: 196864 Overflow Traps Transmitted: 100925440 Current Trap Managers: 0/10 Snmp_Trap_Db Ptr: 30DDCD02 Last Command: dspsnmpstats Next Command:

dspusers

Displays users. The privilege levels in the display are restricted to those of the current user and any privileges below the current user.

Full Name

Display users

Syntax

dspusers

Related Commands

adduser, deluser, dspusers

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dspusers

Description

Display the users on a network.

dspusertask

Displays information about the current user-task. The displayed information varies with the user task. For example, information about a vt session slightly differs from a telnet session. The command takes a user task number as an argument. If the user task number is unknown, enter the command without a number to see a list of possible user tasks and the current user task. The types of user tasks are as follows:

Full Name

Display user task

Syntax

dspusertask [user task number]

Related Commands

adduser, cnfpwd, deluser, dspusers, dsppwd

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dspusertask

Description

Display user task information—without specifying a task in this case. This example shows a case in which the user has started a vt session on a node. See also step 2 of this example.

System Response
sw78 VT SuperUser BPX 15 9.2 Jan. 31 1998 15:52 PST # TASK PURPOSE USER ID # TASK PURPOSE USER ID -- ---- ------------ ------- -- ---- ------------ ------- 1 USR1 control port none 13 VT-5 VT none 2 USR2 auxilry port none 14 VT-6 VT none 3 USR3 lan port(SV) none 15 SNMP agent n/a 4 TN-1 lan (telnet) none 16 JOBS runs jobs n/a 5 TN-2 lan (telnet) none 6 TN-3 lan (telnet) none 7 TN-4 lan (telnet) none 8 TN-5 lan (telnet) none 9 VT-1 VT: sw81 SuperUser < You 10 VT-2 VT none 11 VT-3 VT none 12 VT-4 VT none This Command: dspusertask Please Enter User Number:9
Example 2

9

Description

This example shows the screen after the you enter a 9 at the prompt in the previous screen, a case in which you already started a vt session on a node. Note that the display shows the status as a vt slave, and the node on which the vt session originated is sw81.

sw78 VT SuperUser BPX 15 9.2 Jan. 31 1998 15:53 PST Task: VT-1 Logged in as: SuperUser VT master: no VT slave: yes Master node is: sw81 VT pending: no Public lock: no Private lock: none No command is currently running. Previous command: dspusertask 9 Last Command: dspusertask 9 Next Command:


Table 13-14: dspusertask—Parameters
Parameter Description

user task number

Specifies the number of the user task whose information is displayed.

dspusertasks

Displays general information about all current user tasks. The types of user tasks are as follows:

Full Name

Display user tasks

Syntax

dspusertasks

Related Commands

adduser, cnfpwd, deluser, dspusers, dsppwd, dspusertask

Attributes

Privilege Jobs Log Node Lock

1-6

No

No

IGX, BPX

No

Example 1

dspusertasks

Description

Display user task information.

System Response
sw151 TN SuperUser IGX 8420 9.2 Aug. 14 1998 18:02 GMT # TASK PURPOSE USER ID # TASK PURPOSE USER ID -- ---- ------------ ------- -- ---- ------------ ------- 1 USR1 control port SuperUser 13 VT-5 VT none 2 USR2 auxilry port none 14 VT-6 VT none 3 USR3 lan port(SV) none 15 SNMP agent n/a 4 TN-1 lan (telnet) none 16 JOBS runs jobs n/a 5 TN-2 lan (telnet) SuperUser < You 6 TN-3 lan (telnet) none 7 TN-4 lan (telnet) none 8 TN-5 lan (telnet) none 9 VT-1 VT none 10 VT-2 VT none 11 VT-3 VT none 12 VT-4 VT none Last Command: dspusertasks Next Command:


hometocprevnextglossaryfeedbacksearchhelp
Posted: Mon Aug 19 21:33:50 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.