|
To achieve peak network performance, the routing of traffic and use of available bandwidth is configurable. The information used in configuring traffic routing and bandwidth is gathered from historical network trends. The tasks required to optimize the network are: specifying channel utilization, specifying the class of service, and managing bandwidth. These tasks are discussed in the paragraphs that follow.
Use the cnfchutl command to specify the expected utilization of Frame Relay, data, or voice channel as a percentage of the channel's total capacity. The specified value can be in the range of 0% to 100%. 100% is the default for data and Frame Relay channels. The default for voice channels is 40%. To display the utilization of a particular trunk, use the dsptrkutl command. This command displays a details on the packets transmitted over the trunk. The user can specify the rate in seconds at which the screen is updated. Use the dspload command to display the load for a specified trunk at a node.
Use the cnfcos command to specify a class of service (COS) for a Frame Relay, data, or voice channel. The class of service is the delay in seconds before the network reroutes a connection in the event of a trunk failure. The range is 0-15. By spreading out the COS numbers to vary the rerouting delay, one class of channels has a chance to reroute before the another class starts to reroute.
There are a number of commands that assist in managing bandwidth to achieve satisfactory traffic patterns.
upcon, dncon | The up and down connection commands can be used to temporarily down connections of a specified COS, thus releasing bandwidth for other services. Often it is possible to down some voice connections to provide more bandwidth for data and Frame Relay connections. |
cnfpref | The configure preference command can be used to specify preferred routing for intra-domain connections. This command can be used to assist in balancing the load on the network's trunks. |
dsprts, prtrts | The display and print routes commands can be used in conjunction with the cnfpref command to display the current connection routing information. |
Table 10-1 shows the full command name and starting page for each description.
Command | Description | Page |
---|---|---|
cnfchutl | Configure channel utilization | |
cnfcmb | Configure combined timeout parameters | |
cnfcos | Configure class of service | |
cnfpref | Configure preferences | |
cnfrtcost | Configure cost based routing | |
dncon | Down connections | |
dspload | Display load | |
Display open space for routes | ||
dsprts | Display routes | |
dsptrkutl | Display trunk utilization | |
prtrts | Print routes | |
upcon | Up connections |
Informs the system software of the expected utilization rate of connections with traffic-dependent compression algorithms (voice connections with VAD, data connections with DFM, Frame Relay connections, FastPAD voice connections with ATC-8K, ATC-12K, ATC-16K, or CELP-8K compression). The software load model then takes the user-specified rate of the connection and modifies it by using the percent of utilization you specify with cnfchutl. The resulting rate is used in calculations for loading trunks. The load model uses these figures instead of calculated estimates from real traffic patterns.
On a FastPAD channel, the compression rate adapts to the congestion level within the network. The configured compression rate indicates the maximum rate for the channel. FastPAD channels detect FAX signals and adapt their rates for FAX transmittal. For the full benefits of the compression algorithms to be used, the default utilizations should be modified after traffic studies have been performed. Also, traffic studies of Frame Relay connections should be used to determine optimum utilization settings. When calculating loads in a network, the load allocated to a connection is:
For example, with a channel utilization of 50% and a full load of 480 packets per second, the load allocated to a connection is:
For data connections with DFM turned off, for voice connections with VAD turned off, and for all FastPAD data connections, the bandwidth allocated is always the maximum bandwidth for the connection type. In other words, the utilization, although configurable, is ignored for a voice channel without VAD, a data channel without DFM and all FastPAD data channels.
If you use cnfchutl to increase the utilization of a connection, the system verifies that the additional bandwidth is available on the connection's current route. If the bandwidth is not available, the system attempts to reroute the connection. If no other route is found, the connection is failed.
If you use cnfchutl to decrease the utilization of a connection, the system makes the bandwidth available to other connections that require a route. The screen displayed by the cnfchutl command depends upon whether a data channel, voice channel, or Frame Relay channel is specified.
Configure channel utilization
cnfchutl <channel(s)> <%_util>
dspchcnf
Privilege | 1-2 |
Jobs | Yes |
Log | Yes |
Node | IPX, IGX |
Lock | Yes |
cnfchutl 5.1 40
Description
Set utilization on data channel 5.1 at 40%.
alpha TRM YourID:1 IPX 16 9.1 Aug. 23 1997 10:45 PST
Maximum EIA % DFM Pattern DFM
Channels Update Rate Util Length Status
5.1 15 40 8 Enabled
5.2-4 2 100 8 Enabled
Last Command: cnfchutl 5.1 40
Next Command:
cnfchutl 14.1 55
Description
Set utilization on voice channel 14.1 at 55%.
alpha TRM YourID:1 IPX 16 9.1 Aug. 16 1997 10:10 PST
% Adaptive Gain (dB) Dial OnHk Cond
Channels Util Voice In Out Type Interface Type A B C D Crit.
14.1 55 Enabled -4 - User Unconfig ? ? - - a
14.2-24 40 Enabled 0 - Inband Unconfig ? ? - - a
Last Command: cnfchutl 14.1 55
Next Command:
cnfchutl 8.1.100 60
Description
Set utilization on Frame Relay channel 8.1.100 at 60%.
alpha TRM YourID:1 IPX 16 9.1 Aug. 23 1997 10:45 PST
Frame Relay Channel Configuration Port: 8.1
From Minimum Peak AvgFrame Cmax VC Q ECN Q % Util
8.1.100 9.6 * 70 10 65535 65535 60
8.1.301 9.6 * 70 10 65535 65535 100
Last Command: cnfchutl 8.1.100 60
Next Command:
Parameter | Description |
---|---|
channel | Specifies the channel for configuring utilization. The channel can be in voice, data, Frame Relay, or FastPAD voice or data. The format for channel depends on the technology, as follows:
|
percent utilization | Specifies the percentage of utilization of the channel. The is range 0-100. The default value for data or Frame Relay is 100%. The default value for voice is 40%. |
Configures a time the node waits for a second packet to become available for placing in an ATM cell. You can use the cnfcmb command to control the time that the node waits for individual traffic types. When you enter a value for a parameter, switch software multiplies the value by 125 microseconds to derive the timeout.
Configure combine timeout parameters
cnfcmb <parameter number> <value>
dspchcnf
Privilege | service |
Jobs | Yes |
Log | No |
Node | IPX, IGX |
Lock | Yes |
cnfcmb 1 1
Description
Change the timeout for voice packets from the default of 2 * 125 microseconds to 1 * 125 microseconds.
pubsigx1 TN SuperUser IGX 32 9.1 Sep. 17 1997 23:38 PDT
System-Wide Combine Timeout Parameters
1 Packet Combining Timeout for Voice (125 usec *)...................... 2
2 Packet Combining Timeout for Time Stamped Traffic (125 usec *)....... 2
3 Packet Combining Timeout for High Priority Traffic (125 usec *)...... 0
4 Packet Combining Timeout for Non Time Stamped Traffic (125 usec *)... 2
5 Packet Combining Timeout for Bursty Data 1 Traffic (125 usec *)...... 255
6 Packet Combining Timeout for Bursty Data 2 Traffic (125 usec *)...... 255
This Command: cnfcmb
Which parameter do you wish to change: 1 1
Parameter | Description | Default |
---|---|---|
1 | Timeout for Voice (multiplied by 125 microseconds) | 2 |
2 | Timeout for Time Stamped Traffic (multiplied by 125 microseconds). | 2 |
3 | Timeout for High Priority Traffic (multiplied by 125 microseconds) | 0 |
4 | Timeout for Non Time Stamped Traffic (multiplied by 125 microseconds) | 2 |
5 | Timeout for Bursty Data 1 Traffic (multiplied by 125 microseconds) | 255 |
6 | Timeout for Bursty Data 2 Traffic (multiplied by 125 microseconds) | 255 |
Determines the priority for rerouting a connection. You determine the priority by specifying a delay before the network reroutes one or more failed connections. The COS applies to:
When connections have failed (typically due to a trunk failure), the network reroutes them according to priorities that are set primarily by the class of service (COS). The value of COS is the number of seconds the network waits before it begins to reroute the connection, so the COS determines the rerouting order for connections owned by a node. The range of possible COS values is 0-15.
The number of connections in a network has an effect on the increment between COS values you should use. For larger numbers of connections, you should allow more time to reroute the connections in a class. To facilitate the greater time required to reroute larger numbers of connections, use a larger increment between COS values. In a larger network, for example, you could specify COS values that are 3 seconds apart (such as 0, 3, 6, 9, 12, and so on, for example). For a network with less traffic, assign COS values in increments of 1 or 2. This strategy ensures that all connections of a given COS reroute before the connections with the next COS start to reroute.
Configure class of service for connections
cnfcos <group | channel(s)> <cos>
dspcons
Privilege | 1-2 |
Jobs | Yes |
Log | Yes |
Node | IPX, IGX |
Lock | Yes |
cnfcos 5.1 0
Description
Set the COS for channel 5.1 to 0.
alpha TRM YourID:1 IPX 16 9.1 Aug. 16 1997 10:12 PST
Local Remote Remote Route
Channel NodeName Channel State Type Compression Code Avoid COS O
5.1 beta 25.1 Ok 256 7/8 0 L
9.1.100 gamma 8.1.200 Ok fr 0 L
9.2.400 beta 19.2.302 Ok fr 0 L
14.1 gamma 15.1 Ok v 0 L
Last Command: cnfcos 5.1 0
Next Command:
Parameter | Description |
---|---|
channels | Specifies the voice, data, Frame Relay, or Fast PAD voice/data channel(s), where channel is one of the following:
|
cos | Specifies the class of service number to assign to the channel, range of channels, or connection group. The range is 0-15 seconds, so the rerouting priority is inversely proportional to the COS (a low COS values means a high routing priority). |
Specifies the preferred route for a connection or range of connections. Enter cnfpref only at a node that is an end point of the connection. This command applies only to connections that exist within a domain. Do not attempt to execute cnfpref on connections that exist between domains.
The preferred route for a connection is used when possible. If the preferred route is different from the existing route, the connection automatically moves to the preferred route whenever network conditions allow (for example, when trunks are out of alarm and sufficient bandwidth exists).
Configure preferred route for connections
cnfpref <channel(s) | *> <route> < + | -> [d]
dsprts
Privilege | 1-2 |
Jobs | Yes |
Log | Yes |
Node | IPX, IGX, BPX |
Lock | Yes |
cnfpref 14.1 13/beta 15/gamma d
Description
Select the preferred route for channel 14.1 to be through beta trunk 13 to beta then to gamma trunk 15. For gamma, the "d" in the command specifies that the route is directed.
alpha TRM YourID:1 IPX 16 9.1 Aug. 16 1997 10:22 PST
From 14.1 Route
14.1
alpha 14--13beta 15--15gamma
Pref:(D) alpha 14--13beta 15--15gamma
Last Command: cnfpref 14.1 13/beta 15/gamma d
Next Command:
cnfpref 6.4 -
Description
Remove the preferred route for channel 6.4.
cnfpref * +
Description
Designate the current routing of all locally owned connections to be the preferred routing. Using a "-" instead of a "+" in the command would remove the preferred routing designation of all locally owned connections.
alpha TRM YourID:1 IPX 16 9.1 Aug. 23 1997 10:48 PST
Chan/Grp Route
5.1
alpha 10-- 7beta
Pref: alpha 10-- 7beta
9.1.100
alpha 14--13beta 15--15gamma
Pref: alpha 14--13beta 15--15gamma
9.1.200
alpha 10-- 7beta 15--15gamma
Pref: alpha 10-- 7beta 15--15gamma
9.2.400
alpha 10-- 7beta
Pref: alpha 10-- 7beta
Last Command: cnfpref * +
Next Command:
Parameter | Description |
---|---|
channels | Specifies the channel or range of channels for preferred route configuration. The channel specifier has one of the following formats
A "*" specifies all locally owned connections and applies only to the "+" and "-". |
route | Designates the preferred route for the connection(s) to take through the network. The route is designated by one or more "trunk/node name" pairs. At a given node alpha, for example, entering a route of "12/delta 6/epsilon", would route the connection from alpha to delta via delta's trunk 12. The connection would then go from delta to epsilon via epsilon's trunk 6. A "+" causes the connection's current route to become the preferred route. A "-" removes the connection's preferred route designation. |
Parameter | Description |
---|---|
d | Specifies directed routing. If the preferred route is not available, the connection is failed. |
Configures the cost cap for a connection when cost-based routing is configured.
A maximum allowable cost value (cost cap) is used during route determination to prevent selection of a route which exceeds an acceptable cost. For routing based on delay, the cost cap is the acceptable end-to-end delay for the connection type. This cap is configured network-wide per delay-sensitive connection type.
For routing based on trunk cost, the cost cap is the acceptable end-to-end cost. This cap is configured per connection. The default cost cap is 100, which is derived from the maximum hops per route (10) and default cost per trunk (10). The cost cap can be changed at any time. If the cost cap is decreased below the current route cost, the connection is not automatically rerouted. A manual reroute is required to route the connection to fit under the new cost cap. This gives the user more control over the connection reroute outage.
Display connection loading
cnfrtcost <connection> <max cost>
<connection> indicates the connection endpoint (that is, slot.port.vpi.vci)
<max cost> indicates the maximum allowable route cost
Valid values = 1 - 100
dspcon, cnfpref, dsprtcache
Privilege | 1-2 |
Jobs | Yes |
Log | Yes |
Node | IPX, IGX, BPX |
Lock | Yes |
cnfrtcost 9.2.5.100 40 1
After configuring the cost cap for a connection, you can check to see the configured value with the dspcon command, as is shown in the System Response example. This is the dspcon response for 9.2.5.100 with the additional fields of Max Cost (40) and Route Cost (1). For a route optimized on trunk delay, the cost labels are updated to indicate delay: Max Cost becomes Max Delay and Route Cost becomes Route Delay.
Select route cost for channel 9.2.5.100.
sw203 TN StrataCom BPX 15 9.1.a4 Sep. 24 1997 18:18 GMT
Conn: 9.2.5.100 sw242 14.2.5.100 cbr Status:OK
PCR(0+1) % util CDVT(0+1) Policing
50/50 100/100 10000/10000 4/4
Owner: LOCAL Restriction: NONE COS: 0
TestRTD: 0 msec Trunk Cell Routing Restrict: Y Max Cost: 40 Route Cost: 1
Path: sw203 3.1.1-- 2.1.1sw242
Pref: Not Configured
sw203 ASI-T3 : OK sw242 ASI-OC3 : OK
Line 9.2 : OK Line 14.2 : OK
OAM Cell RX: Clear NNI : OK
NNI : OK
Last Command: dspcon 9.2.5.100
Next Command:
Deactivates (downs) a connection, bundle of connections, a connection group or all connection in a COS or COS range. The dncon command temporarily removes one or more connections from the network. This command is useful for temporarily removing voice connections when additional bandwidth is necessary for other types of connections.
Connections can be downed immediately or with courtesy. Even with immediate downing, a prompt appears that requests confirmation. With courtesy downing, the system waits until the connection is onhook before downing the connection. Courtesy downing is possible only if the onhook status has been configured with the cnfvchtp command. Courtesy downing is not available for FastPAD connections because the signaling information between the end points is not visible to the IPX or IGX node. The upcon command reactivates the voice connections. The up/down status of the voice connections appears in the "State" column of the dspcons screen. Table 10-7 shows each item in the State column.
State | Description |
---|---|
"OK" (routed) | Connection is activated and able to carry traffic. |
"Down" | Connection has been added to the network database but is not activated and is not able to carry traffic. |
"OK(Dn)" | Waiting for onhook to occur to allow courtesy down to take place for connection(s) that have been courtesy downed using the dncon command. |
"Failed" | Unrouted, but trying to reroute. |
Down connection
dncon {<group | local_chan(s)> | COS <cos_range>} {i | c}
upcon
Privilege | 1-2 |
Jobs | Yes |
Log | Yes |
Node | IPX, IGX |
Lock | Yes |
dncon 14.1 c
Description
Down connection 14.1 with courtesy.
dncon 14.1 i
Description
Down connection 14.1 immediately.
dncon cos 4-8 c
Description
Courtesy down on-hook connections network-wide with COS 4 through 8. This command marks all connections that may be courtesy downed at one time and does not monitor new connections or those that later fit the COS.
dncon 3.1.100 i
Description
Immediately down connection 3.1.100.
pubsigx1 TN SuperUser IGX 32 9.1 Aug. 26 1997 16:51 GMT
Local Remote Remote
Channel NodeName Channel State Type Compress Code COS
3.1.100 pubsigx1 3.2.200 Ok fr
3.2.200 pubsigx1 3.1.100 Ok fr
This Command: dncon 3.1.100 i
Down these connections (y/n)?
dncon cos 4-8 i
Description
Immediately down all connections network-wide with COS 4 through 8. This command executes once, so if individual connections are subsequently upped or new connections added in this COS range, they remain up.
dncon cos 14.1.3
Description
Down FastPAD voice connection 14.1.3.
dncon cos 14.1.1.5
Description
Down FastPAD data connection 14.1.1.5.
Parameter | Description |
---|---|
channels or group | Specifies a group, a channel, or a range of channels to down. |
cos range | Specifies the COS or COS range. The range is 0-15. |
Parameter | Description |
---|---|
i/c | Specifies immediate downing (i) of the specified connections or courtesy downing (c) of the specified connections. |
Displays both the used and available bandwidth (both in the transmit and receive directions) for each trunk at the specified node. The "transmit" direction is from the node specified and to the node at the other end of the trunk. In the screen display, the numbers of disabled trunks appear in dim, reverse video on the screen.
The dspload display reflects the static load model stored by the node and used to determine the bandwidth available for new connections and reroutes. The display does not represent changes due to the dynamic utilization of the trunks. Some types of connections, such as voice connections using adaptive voice and data connections using Data Frame Multiplexing (DFM), suppress packets. In contrast, Frame Relay connections may generate additional packets when bandwidth permits.
When this command is executed at a local node in structured networks, the information displayed is for any node on the intra-domain lines belonging to the same domain. When this command is executed at a junction node, the information displayed is for all inter-domain lines between all junction nodes. The node uses the terminating and through routed connections' calculated load to calculate the trunk load. The connection type (v, c, a, or d) or baud rate (9.6 Kbps, 56 56 Kbps, and so on) and other factors determine its basic load. The calculated trunk load is also modified by the cnfchutl command for connections that use VAD, DFM, or Frame Relay.
A certain amount of bandwidth is reserved for each trunk (using cnftrk). The reserved bandwidth is available only for high priority packets (e.g. PCC traffic). The node cannot route connections using this reserved bandwidth. The following loading, in packets per second, is calculated for each trunk in each direction:
If the dspload arguments include a trunk number, detailed information for each of the packet types on that line appears. See Example 2. Additional categories of information for Frame Relay loads on the trunk include Cmax In Use, Cmax Available, and Cmax Capacity.
In Release 9.1, as shown in Example 3, the dspload screen will also display the configure Trunk Cost and the Trunk Qdelay when cost-based routing is configured.
Display connection loading
dspload [nodename] [line number] [-j | -l ]
dspplnutl, cnfcmparm
Privilege | 1-6 |
Jobs | No |
Log | No |
Node | IPX, IGX |
Lock | No |
dspload
Display the load for all trunks that terminate on the current node.
alpha TRM YourID:1 IPX 16 9.1 Aug. 16 1997 11:54 PST
Packet Line loads for node 'alpha'
Units Used Available Reserved Cmax In Use Cmax In Use
PLN Xmt Rcv Xmt Rcv Xmt Rcv Xmt Rcv XmtA RcvA XmtB RcvB
10 Pkts Pkts 1760 1744 8304 8320 600 600 0 0 0 0
14 Pkts Pkts 504 504 6896 6896 600 600 20 20 0 0
Last Command: dspload
Next Command:
dspload 10
Description
Display the load for the trunk in slot 10 of the current node.
sw151 TN SuperUser IGX 16 9.1 Aug. 26 1997 17:05 GMT
Configured Packet Line Loading: PLN sw151 10--10 sw150
Load Type Xmt-p Rcv-p lcl
NTS 2016 2016 Conid In Use 11
TS 432 432 Conid Available 1760
Voice 208 208 Total Capacity 1771
BData A 0 0
BData B 0 0 Line type is Terrestrial
CBR 0 0 Line supports BData Load
VBR 0 0 Line does not use ZCS
ABR 0 0 Traffic class:
Total In Use 2656 2656 V TS NTS FR FST CBR VBR ABR
Reserved 992 992
Available 76352 76352
Total Capacity 80000 80000
Last Command: dspload 10
Next Command:
dspload 1.1
Description
Display the load for trunk 1 in slot 1 of the current node, which includes the Trunk Cost because cost-based routing is configured. The trunk queue delay is also displayed if routing with delay is enabled.
sw203 TN SuperUser BPX 15 9.1 Sep. 24 1997 17:05 GMT
Configured Trunk Loading: TRK sw203 1.1-- 1.1 sw242
Load Type Xmt-c Rcv-c lcl
NTS 0 0 Conid In Use 1068
TS 0 0 Conid Available 703
Voice 0 0 Total Capacity 1771
BData A 0 0
BData B 0 0 Trunk cost: 26
CBR 23100 23100 Trunk V Qdelay: 2.5 msec
VBR 14300 14300 Trunk NTS Qdelay: 31.9 msec
ABR 18901 18901 Trunk is Terrestrial
Total In Use 56301 56301 Trunk does not use ZCS
Reserved 1000 1000 Trunk end doesn't support complex gateway
Available 38699 38690 Traffic class: V TS NTS FR FST CBR VBR ABR
Total Capacity 96000 96000
Last Command: dspload 1.1
Next Command:
Parameter | Description |
---|---|
nodename | Specifies the node. If a node is not specified, the display shows loading on the local node. The node must be in the domain where the command is entered unless the node is a junction node. If the specified node is a junction node, the display shows loading for junction domain lines. |
line number | Specifies the physical line whose loading information is displayed. |
l | j | Specifies either a local or a junction node. |
Displays the open space for a connection route.
Display open space for a route
dspospace <connection | group>
none
Privilege | 1-6 |
Jobs | No |
Log | No |
Node | IPX, IGX |
Lock | No |
dspospace 4.1.1
Description
Display the open space for the ATM-Frame Relay connection 4.1.1. The line interface card is a UFM-8C.
sw110 TN SuperUser IGX 16 9.1 Jan. 22 1997 19:11 GMT
Open Space for 4.1.1 Snapshot
Domain
Local: sw110 8--10.3sw86 6.2-- 6.1sw81
ms_cur_pkts: 524272 ms_cur_cells: 12576
sm_cur_pkts: 4368 sm_cur_cells: 11296
Last Command: dspospace 4.1.1
Next Command:
Parameter | Description |
---|---|
connection | Specifies the connection. |
New in Release 9.1, this command displays the cache of all cost-based routing connections. The optional 'index' parameter lets you specify a cache entry index. The optional 'c' parameter clears the cache. The information displayed includes:
Display cost-based route cache
dsprtcache [index] [c]
[index] specifies the cache entry index
[c] specifies to clear the entire cache or a single entry
dspcon, cnfrtcost, cnfpref
Privilege | 1-6 |
Jobs | No |
Log | No |
Node | IPX, IGX, BPX |
Lock | No |
dsprtcache
Display route cache contents, and let you monitor and manually clear the cache.
pissaro TN StrataCom BPX 15 9.1 Jun. 18 1997 11:11 GMT
Route Cache (Summary)
Index Use # Cost Delay Restrict Load VPC Hops RemoteNode
0 Yes 1 Yes No None VBR No 2 lautrec
1 Yes 6 Yes No *s BDB No 3 vangogh
2 Yes 9 Yes No None BDA No 3 matisse
3 Yes 3 Yes No *t BDB No 3 rousseau
4 Yes 1 Yes No None CBR No 3 seurat <- current
5 No 0 No No None --- No 0 ---
6 No 0 No No None --- No 0 ---
7 No 0 No No None --- No 0 ---
8 No 0 No No None --- No 0 ---
9 No 0 No No None --- No 0 ---
10 No 0 No No None --- No 0 ---
11 No 0 No No None --- No 0 ---
Last Command: dsprtcache
Next Command:
Parameter | Description |
---|---|
index | Specifies a particular route entry within the cache. When used with the c parameter, the route is either displayed or cleared from the cache. |
c | Clears the cache, or if you also enter the index parameter, clears the route cache specified by the index number. |
Displays the routes used by all connections at a node. The display shows the trunk numbers and names of all nodes in the path. For FastPAD connections, the displayed connection routes terminate at the IPX or IGX nodes. A blinking trunk indicates a failed line. A tilde trunk (~) indicates a satellite line.
In Release 9.1, dsprts also displays the current cost for all connection routes. A derouted connection shows no current cost. A connection route optimized with trunk delay shows the current total delay. A highlighted connection on the display has exceeded the maximum route cost.
Display connection routing
dsprts [start group | chan] [nodename]
cnfpref
Privilege | 1-6 |
Jobs | No |
Log | No |
Node | IPX, IGX, BPX |
Lock | No |
dsprts
Description
Display the connection routes.
sw203 TN SuperUser BPX 15 9.1 Sep. 24 1997 17:47 GMT
Conn Route
9.1.1.* (Cost = 5)
sw203 1.1-- 1.1sw242
Pref: Not Configured
9.2.5.100 (Cost = 1)
sw203 3.1.1-- 2.1.1sw242
Pref: Not Configured
9.2.5.101 (Cost = 1)
sw203 3.1.1-- 2.1.1sw242
Pref: Not Configured
9.2.5.102 (Cost = 5)
sw203 1.1-- 1.1sw242
Pref: Not Configured
This Command: dsprts
Continue?
Parameter | Description |
---|---|
start group or channel | Specifies the starting group or channel with which to begin the display. Channel displays are in numeric order. If no starting channel is specified, the display begins with the first connected channel. Start channel is specified in one of the following formats: Voice connection: slot.channel Data connection: slot.port Frame relay connection: slot.port.DLCI Frame relay connection group: remote node.groupname Access device connection: slot.port.device_ID FastPAD voice connection: slot.port.subport FastPAD data connection: slot.port.subslot.subport |
node name | Specifies that connections from only the local node to the current node are displayed. If no nodename is entered, connections from the local node to all other nodes are displayed. |
Displays dynamic utilization information for a specified trunk. The trunk must be upped and added to use this command. The following lists the trunk utilization and terminated connection parameters included in the display. The parameter values are updated according to the specified or default interval and the screen remains displayed until the DEL key is depressed. Disabled trunks have their trunk number displayed in dim, reverse video on the screen.
Trunk Utilization Parameters and Statistics | Description |
---|---|
Elapsed Time (seconds) | Elapsed time in seconds.since the command was started |
Total Packets Transmitted | Number of packets transmitted during the elapsed time. |
Overall Packet Rate | Number of packets transmitted per second during the (pkts/sec)elapsed time. |
Overall utilization | Bandwidth used, expressed as a percentage of the available bandwidth during the elapsed time. This is: 100 x ("Total packets transmitted")/("Elapsed Time" x bandwidth (in packets per second)). |
Peak Interval Utilization | Bandwidth used, expressed as a percentage of the available bandwidth during the peak interval. This is: 100 x ("Total packets transmitted")/("Peak Interval" x bandwidth (in packets per second)). |
Last Interval (seconds) | Elapsed time, in seconds, for the last screen update interval. |
Interval packets generated | Number of packets transmitted during the last interval. |
Interval packet rate (pkts/sec) | Number of packets transmitted per second during the last interval. |
Interval utilization | The used bandwidth expressed as a percentage of the available bandwidth during the last interval. The derivation of interval utilization is as follows: 100 x ("Interval packets transmitted") / ("Last Interval" x bandwidth (in packets per second)). |
Total Connections | Total number of connections routed over the trunk. |
Terminated/Via | Terminated: Number of connections routed over the trunk that terminate at this node. Via: Number of connections routed over the trunk that do not terminate at this node. |
Terminated Connection Statistics | Description |
---|---|
Voice terminated | Number of voice connections terminated at this node that are routed over his trunk. |
Data terminated | Number of data connections terminated at this node that are routed over this trunk. |
Frame relay terminated | Number of Frame Relay connections terminated at this node that are routed over this trunk. |
Num voice offhook | Number of voice connections off-hook that are terminated at this node and routed over this trunk. |
Connection Type | Voice connection types: c, a, v, p or t. |
Connection Num | Number of terminated voice connections of each type: c, a, v, p and t. |
Modem On | Number of terminated connections with modem detected. |
Modem V.25 | Number of terminated connections with V.25 modem detected. |
VAD Enabled | Number of terminated connections with VAD enabled. |
Display trunk utilization
dsptrkutl <trunk number> [interval]
dspload, dspchhist, dsptrkhist
Privilege | 1-6 |
Jobs | No |
Log | No |
Node | IPX, IGX, BPX |
Lock | Yes |
dsptrkutl 5.3
Description
Display trunk utilization for port 3 of the BNI in slot 5. The node is a BPX.
bootzilla TN SuperUser BPX 15 9.1 Aug. 27 1997 15:21 GMT
TRK 5.3 Utilization Display
Elapsed time (seconds) 160.1 Terminated Connection Statistics
Total cells transmitted 30 Voice terminated 0
Overall cell rate (cells/sec) 0 Data terminated 0
Overall utilization 0% ATM and FR terminated 1584
Peak interval utilization 1% Num voice OffHook 0
Last interval (seconds) 5.1
Interval cells generated 0 Connection Modem Modem VAD
Interval cell rate (cells/sec) 0 Type Num On V.25 Enabled
Interval utilization 0% c 0 0 0 0
a 0 0 0 -
Terminated Connections 1584 v 0 0 0 0
Via Connections and Groups 0 p/t 0 0 0 -
This Command: dsptrkutl 5.3
Hit DEL key to quit:
Parameter | Description |
---|---|
trunk number | Specifies the number of the trunk in the format slot.trunk. If the card has only one trunk, you can enter just the slot. |
Parameter | Description |
---|---|
interval | Specifies the number of seconds between screen updates. The range is 1-60. The default is 5. |
Prints the connection routes for channels on the IPX or IGX node. It uses the same syntax and prints the same information as the dsprts command. See the dsprts description for output information.
Print connection routes
prtrts [start_channel] [dest_nodename]
dsprts
Privilege | 1-6 |
Jobs | Yes |
Log | No |
Node | IPX, IGX |
Lock | Yes |
prtrts
Description
Print connection routes.
None available as command produces hardcopy.
Parameter | Description |
---|---|
start channel | Specifies the channel with which to print. Channels are printed in numeric order. If no starting channel is specified, the display begins with the first connected channel. Start channel is specified in one of the following formats: slot.channel voice connection. slot.port data connection. slot.port.DLCI Frame Relay connection. remote node.groupname Frame Relay connection group. slot.port.subport FastPad voice connection. slot.port.subslot.subport FastPAD data connection. |
destination node name | Specifies the printing of connection routes from only the local node to the current node. Without a specified node name, the printout shows connections from the local node to all other nodes. |
Ups (activates) a connection, bundle of connections, group of connections, or all connections with a COS or COS range. When a connection is upped, the system tries to route. If the connection cannot immediately be routed, the connection is failed and generates a major alarm. The State display column in an upcon or dspcons screen has the following meaning:
♦ "OK" | (routed). |
♦ "Down" | (downed). |
♦ "OK(Dn)" | (waiting for onhook to occur to allow courtesy down to take place for connection(s) that have been courtesy downed using the dncon command. |
♦ "Failed" | (not routed, but trying). |
Up a connection
upcon {<group | local_chan(s)> | COS <cos_range>}
dncon, dspcon, dspcons
Privilege | 1-2 |
Jobs | Yes |
Log | Yes |
Node | IPX, IGX |
Lock | Yes |
upcon 5.1
Description
Activate connections 5.1.
alpha TRM YourID:1 IPX 16 9.1 Aug. 23 1997 11:33 PST
Local Remote Remote Route
Channel NodeName Channel State Type Compression Code Avoid COS O
5.1 beta )25.1 Ok 256 7/8 0 L
9.1.100 gamma 8.1.200 Ok fr 0 L
9.1.200 gamma 8.1.300 Ok fr 0 L
9.2.400 beta 19.2.302 Ok fr(Grp) 0 L
14.1 )gamma 15.1 Ok v 0 L
Last Command: upcon 5.1
Next Command:
upcon 9.1-4
Activate a range of connections 9.1-4
upcon alpha
Activate a Frame Relay group connection
upcon 9
Activate all downed connections with a COS of 9
upcon cos 9-12
Activate all downed connections with a COS of 9-12
upcon-Parameters
group or channel(s) Specifies a group, a channel, or a range of channels to activate. COS /cos range Specifies the COS or COS range. The range is 0-15.
Parameter
Description
Posted: Thu Aug 22 09:36:41 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.