Managing the Network

This chapter tells you how to use network administration commands. Examples of the tasks these commands perform are: creating a password, setting the network date and time, and adding a user.

Signing on to a node is a two-step process that requires you to enter a User ID and a password. The system or network administrator can provide a User ID and password to you. The user ID can be up to 12 characters. To protect the security of the system, you should change your password regularly. Only your system administrator can change the User ID. To sign on to a node:

Step 1 Enter your user ID at the system prompt "Enter User ID."

Step 2 Enter your password at the "Enter Password" prompt. For initial sign-on, enter the password that the system administrator provides. You can change the password with the cnfpwd command.

After you sign on, the system is ready and so prompts you for the next command.

Signing Off the System

When you have completed a session and want to sign off, use the bye command. This command returns the display to the initial system sign-on prompt. If you enter the bye command when you have a virtual terminal connection to another node, the bye command ends the virtual terminal session and returns to the a local session. To end the local session and thus sign-off the system, again enter the bye command.

Creating a New Password

To change the password, takes the step in the list that follows. given to you by your System Administrator, or to change your present password to a different one, perform the following. To ensure the security of your system, your password should be changed on a regular basis. See the System Administrator for the recommended frequency of change.

Step 1 Enter the cnfpwd command. The system prompts for your current password.

Step 2 Enter your current password. The system prompts for a new password.

Step 3 Enter a new password. Passwords must have 6-15 characters. The system prompts you to confirm the new password by typing it again.

Set Date and Time

Date and time are network-wide parameters. You can set the time zone for each node. The cnfdate command lets you set both time and date. The cnftime command lets you set the time for the entire network.

Summary of Commands

Table 13-1 shows the full name and starting page for the description of each network management command.

Command	Description	Page
adduser	Add user(s)	13-3
cnfdate	Configure date	13-5
cnfpwd	Configure password	13-7
cnfsnmp	Configure SNMP parameters	13-8
cnfstatmast	Configure statistics master SV+ address	13-9
cnfsysparm	Configure system parameters	13-10
cnftime	Configure time	13-15
deluser	Delete user	13-17
dspnwip	Display network IP interface	13-19
dsppwd	Display password	13-20
dspsnmp	Display SNMP parameters	13-22
dspsnmpstats	Display SNMP statistics	13-24
dspusers	Display users	13-26
dspusertask	Display user task	13-27
dspusertasks	Display all user tasks	13-29

Table 13-1: Commands for Managing a Network

Command Description Page

adduser

Add user(s)

13-3

cnfdate

Configure date

13-5

cnfpwd

Configure password

13-7

cnfsnmp

Configure SNMP parameters

13-8

cnfstatmast

Configure statistics master SV+ address

13-9

cnfsysparm

Configure system parameters

13-10

cnftime

Configure time

13-15

deluser

Delete user

13-17

dspnwip

Display network IP interface

13-19

dsppwd

Display password

13-20

dspsnmp

Display SNMP parameters

13-22

dspsnmpstats

Display SNMP statistics

13-24

dspusers

Display users

13-26

dspusertask

Display user task

13-27

dspusertasks

Display all user tasks

13-29

adduser

Adds a user to the network. The first time the new user ID is used for logon, a prompt appears asking the user to change from the default password to a new password which they enter using the cnfpwd command. Users with privilege levels 1 through 5 may add users with lower privilege levels. Since privilege level 6 has no user levels below it, level 6 cannot add any users.

Full Name

Add a user

Syntax

adduser <user_id> <privilege_level>

Related Commands

cnfpwd, deluser, dspusers

Attributes

Privilege	1-5
Jobs	No
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

adduser sarah 5

Description

Add a user sarah with privilege level 5.

System Response


alpha          TRM   YourID:1        IPX 16    8.5    Aug. 16 1997 13:48 PST 
                                                                                
YourID       1                                                                  
Sarah        5                                                                  
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
Last Command: adduser Sarah 5                                                   
                                                                                
                                                                                
Next Command:

Parameter	Description
userid	Specifies the name of the user to add.
privilege level	Specifies the privilege level to grant to the added user. The range of levels is 1-6, where 1 is the highest level and 6 is the lowest.

Table 13-2: adduser-Parameters

Parameter Description

userid

Specifies the name of the user to add.

privilege level

Specifies the privilege level to grant to the added user. The range of levels is 1-6, where 1 is the highest level and 6 is the lowest.

cnfdate

Sets the date and time for the entire network. The node broadcasts the specified date and time to every node in the network. The time displayed at each node is consistent with the time zone where the node resides. (See the cnftmzn description.) For the first-time configuration of the date and time in a network, cnfdate requires all the parameters except for second. The default for second is 0. If a date and time already exist in the network, the defaults are the existing values at the moment you enter the cnfdate command. Note that changes to date and time alter the timestamps on StrataView Plus statistics.

Full Name

Configure data and time

Syntax

cnfdate <year> <month> <day> <hour> <minute> [second]

Related Commands

cnftime, cnftmzn

Attributes

Privilege	1
Jobs	No
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

cnfdate 1997 12 16 13 54 11

Description

Set the time to 1:54:11 in the afternoon, August 16 1997. The system prompts:
"Warning: Changing time of day affects StrataView statistics timestamps

Continue?"
Enter "y" to continue or "n" to abort." Upon a "y" response, the system further prompts with: "Hit RETURN to change clock, DEL to abort."

System Response


alpha          TRM   YourID:1        IPX 16    8.5    Aug. 16 1997 13:54 PST 
                                                                                
YourID       1                                                                  
Sarah        5                                                                  
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
Last Command: cnfdate 1997 12 16 13 54 11                                        
                                                                                
Warning: Changing time of day affects StrataView statistics timestamps          
Continue?

Parameter	Description
year	Specifies the year.
month	Specifies the month. The range is 1-12.
day	Specifies the day. The range depends on the month and can be 0-31.
hour	Specifies the hours. The range is 0-23. For example, enter 6 AM as 6 and 6 PM as 18.
minute	Specifies the minute of the hour. The range is 0-59. The default is 0.

Parameter	Description
second	Specifies the seconds. The range is 0-59. The default is 0.

Table 13-3: cnfdate-Parameters

Parameter Description

year

Specifies the year.

month

Specifies the month. The range is 1-12.

day

Specifies the day. The range depends on the month and can be 0-31.

hour

Specifies the hours. The range is 0-23. For example, enter 6 AM as 6 and 6 PM as 18.

minute

Specifies the minute of the hour. The range is 0-59. The default is 0.

Table 13-4: cnfdate-Optional Parameters

Parameter Description

second

Specifies the seconds. The range is 0-59. The default is 0.

cnfpwd

Changes the password associated with a UserID. To change a password, you must log into the node with the UserID whose password you want to change. Passwords are case-sensitive.

In a structured network, each domain requires you to have a password. In each domain, your password and associated privilege level can be the same of different from those in the other domains. For each domain, you can change the password at any node within the domain, including a junction node.

Full Name

Configure password

Syntax

cnfpwd <old password> <new password>

Related Commands

dsppwd, adduser, deluser, dspusers

Attributes

Privilege	1-6
Jobs	No
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

cnfpwd

Description

Change your password.

Parameter	Description
old password	Specifies the old password.
new password	Specifies the new password. Passwords must have 6-15 characters. Only letters, numbers, "_", and "-" are allowed in a password. Spaces are not allowed.

Table 13-5: cnfpwd-Parameters

Parameter Description

old password

Specifies the old password.

new password

Specifies the new password. Passwords must have 6-15 characters. Only letters, numbers, "_", and "-" are allowed in a password. Spaces are not allowed.

cnfsnmp

Configures the SNMP GET and SET community strings.

Full Name

Configure SNMP parameters

Syntax

cnfsnmp <GET community string> <SET community string>

Related Commands

dspsnmp, dspsnmpstats

Attributes

Privilege	1-6
Jobs	No
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

cnfsnmp

Description

Configure the SNMP GET and SET community string parameters.

Parameter	Description
get community string	Specifies the GET community string.
set community string	Specifies the SET community string.

Table 13-6: cnfsnmp-Parameters

Parameter Description

get community string

Specifies the GET community string.

set community string

Specifies the SET community string.

cnfstatmast

Configures an IP address for the Statistics Master process in StrataView Plus. The cnfstatmast command defines the IP address for routing the messages to and from the Statistics Master in StrataView Plus.

The Statistics Master process requests and receives network statistics by using TFTP Get and Put messages. These TFTP messages pass between the node and the Statistics Master over IP Relay. See the cnfnwip description for details on setting a node address.

Full Name

Configure statistics master SV+ address

Syntax

cnfstatmast <IP Address>

Related Commands

cnfnwip, dspnwip

Attributes

Privilege	1
Jobs	Yes
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

cnfstatmast 199.35.96.217

Description

Configure 199.35.96.217 as the IP address for the Statistics Master.

Parameter	Description
ip address	Specifies the IP address for the Statistics Master. IP addresses have 32-bits. The format of an IP address is x.x.x.x, where x is a value in the range 1-255.

Table 13-7: cnfstatmast-Parameters

Parameter Description

ip address

Specifies the IP address for the Statistics Master. IP addresses have 32-bits. The format of an IP address is x.x.x.x, where x is a value in the range 1-255.

cnfsysparm

Configures various system (or network) parameters. Network-wide parameters are configurable only when all nodes in the network are reachable. The parameters you specify with this command apply throughout the network regardless of the node where you execute the command. Take special note of the consequences of how you resolve conflicting values when networks are joined.

Each parameter is selectable by its index number. The paragraphs that follow describe each parameter by index number. Table 13-8 lists the defaults and ranges for each parameter.

Note Using cnfsysparm requires caution because network rerouting or loss of data may result from changes in system parameters. If necessary, consult with the TAC before you use cnfsysparm.

The following paragraphs describe the user-configurable system parameters by index number.

1: Maximum Time Stamped Packet Age is the maximum age a time-stamped packet can have before the switch discards it. If networks are joined and the Maximum Time Stamped Packet Age in the networks differ from each other, the lower value becomes the maximum.
2: Fail Connections On Communication Break - Determines whether connections are conditioned if the node at the other end of the connection becomes unreachable. If networks with different settings are joined, the resolution is to enable this parameter for the new network.
3-7: Maximum Network Delay for various types of compressed voice and high-speed data connections using SDP/LDP on an IPX node or LDM/HDM on an IGX node. When the total queueing delay on a route exceeds this value, connection traffic cannot use the route. The units of measure are milliseconds. When networks with different values are joined, the lower value becomes the Maximum Network Delay.
8-12: Maximum Network Delay for compressed voice and high-speed data connections. When the total queueing delay on a route exceeds the specified number of milliseconds, a connection traffic cannot use the route. When networks with different values are joined, the higher value becomes the Maximum Network Delay. Applicable cards are the UVM, CDP, or CVM.
13: Enable Discard Eligibility (DE) bit for frame relay connections. Frames received with DE set have been sent on connections where the PIR has been exceeded and are eligible to be discarded. Enabling DE automatically enables CLP. CLP is disabled when Discard Eligibility is turned off except on the bursty data B queue when ForeSight is enabled.
14: Use Frame Relay Standard Parameters Bc and Be allows you to substitute the Frame Relay Forum standard Bc for VC Q depth and Be for PIR when you configure frame relay ports and connections. (The affected commands are cnffrport, addcon for Frame Relay, and cnfcon.) Screen displays for frame relay ports and connections reflect the choice for this parameter. Note that, if you change this parameter, a network-wide reset to the default values takes place for all frame relay classes, and the terminal displays a warning that the reset occurred.
Obsolete: 15-20: Maximum Local Delay for Interdomain UVM, CDP, or CVM to UVM, CDP, or CVM connections is similar to parameters 8-12 described above. These parameters are specify the maximum delay at the local domain in a structured network. These delays can be set only on a domain-by-domain basis (not end-to-end).
21: FastPAD Jitter Buffer Size is the size of the buffer for neutralizing jitter in connections that terminate on a FastPAD. The units of measurement are milliseconds.
22: Number of Consecutive Invalid Login Attempts to Cause Major Alarm specifies the number of failed login attempts that causes a major alarm. The default of 0 means that failed login attempts do not cause an alarm.
23: Enable Connection Deroute Delay is an enable that causes the network to wait a period of time before rerouting connections because of an error on a trunk. With Enable Connection Deroute Delay enabled, the network does not immediately reroute connections when statistical errors are occuring or when a trunk momentarily moves into a failure state then returns to normal operation. This feature is relevant when rerouting the connections is more of a disruption than the errors caused by the intermittant trunk.
24: Frame Relay VCs Polling Rate is the period between the start of polling cycles for both ATM and Frame Relay virtual connections. The possible values are 5, 10, and 15 seconds. As the number of connections in a network grows, greater intervals between cycles may be appropriate. The suggested intervals for the numbers of connections are:
- 5 minute polling for up to 4000 connections
- 10 minute polling for up to 8000 connections
- 15 minute polling beyond 8000 connections.
25: Port Polling Rate is the time between the start of polling cycles for interval statistics. The possible values are 5, 10, and 15 minutes. (To specify the particular statistics, use the statistics manager in StrataView Plus.) As the number of connections in a network grows, greater intervals between cycles may be appropriate. The suggested intervals for the numbers of connections are:
- 5 minutes for up to 300 connections
- 10 minutes for up to 500 connections
- 15 minutes for more than 500 connections.

System Parameters
Index	System-Wide Parameter	Default	Range
1	Max Time Stamped Packet Age (in milliseconds).	40	1-60
2	Fail Connections On Communication Break.	No	y or n
3	Max Network Delay for "v" connections (in milliseconds).	14	1-255
4	Max Network Delay for "c" connections (in milliseconds).	27	1-64
5	Max Network Delay for "d" connections (in milliseconds).	14	1-255
6	Max Network Delay for "a" connections (in milliseconds).	27	1-255
7	Max Network Delay for High Speed Data connections (in milliseconds).	40	1-255
8	Max Network Delay for CDP or CVM to CDP or CVM "v'' connections (in milliseconds).	64	1-255
9	Max Network Delay for CDP or CVM to CDP or CVM "c" connections (in milliseconds).	64	1-64
10	Max Network Delay for CDP or CVM to CDP or CVM "t & p" connections (in milliseconds).	64	1-255
11	Max Network Delay for CDP or CVM to CDP or CVM "a" connections (in milliseconds).	64	1-255
12	Max Network Delay for CDP or CVM to CDP or CVM High Speed Data connections (in milliseconds).	64	1-255
13	Enable Discard Eligibility (DE).	No	y or n
14	Use Frame Relay standard parameters Bc and Be.	No	y or n
15	Obsolete: Max Local Delay for Interdom CDP to CDP "v'' connections.	27	1-255
16	Obsolete: Max Local Delay for Interdom CDP to CDP "c" connections.	27	1-64
17	Obsolete: Max Local Delay for Interdom CDP to CDP "t & p" connections.	27	1-255
18	Obsolete: Max Local Delay for Interdom CDP to CDP "a" connections.	27	1-255
19	Obsolete: Max Local Delay for Interdom CDP to CDP High Speed Data connections.	27	1-255
20	Obsolete: Max Local Delay for Interdom High Speed Data connections (in milliseconds).	28	1-255
21	FastPAD De-jitter Buffer Depth (in milliseconds).	15	0-255
22	Number of Consecutive Invalid Login Attempts to Cause Major Alarm.	0	3-9
23	Enable Connection Deroute Delay.	Yes	y or n
24	Frame Relay VCs Polling Rate is the number of minutes between polling cycles for both ATM and Frame Relay virtual connections in the network.	5	5, 10, or 15
25	Port Polling Rate is the is the number of minutes between polling cycles for interval statistics gathered for all ports in the network.	5	5, 10, or 15

Table 13-8: Defaults and Ranges of cnfsysparm Parameters

System Parameters

Index System-Wide Parameter Default Range

1

Max Time Stamped Packet Age (in milliseconds).

40

1-60

2

Fail Connections On Communication Break.

No

y or n

3

Max Network Delay for "v" connections (in milliseconds).

14

1-255

4

Max Network Delay for "c" connections (in milliseconds).

27

1-64

5

Max Network Delay for "d" connections (in milliseconds).

14

1-255

6

Max Network Delay for "a" connections (in milliseconds).

27

1-255

7

Max Network Delay for High Speed Data connections (in milliseconds).

40

1-255

8

Max Network Delay for CDP or CVM to CDP or CVM "v'' connections (in milliseconds).

64

1-255

9

Max Network Delay for CDP or CVM to CDP or CVM "c" connections (in milliseconds).

64

1-64

10

Max Network Delay for CDP or CVM to CDP or CVM "t & p" connections (in milliseconds).

64

1-255

11

Max Network Delay for CDP or CVM to CDP or CVM "a" connections (in milliseconds).

64

1-255

12

Max Network Delay for CDP or CVM to CDP or CVM High Speed Data connections (in milliseconds).

64

1-255

13

Enable Discard Eligibility (DE).

No

y or n

14

Use Frame Relay standard parameters Bc and Be.

No

y or n

15

Obsolete: Max Local Delay for Interdom CDP to CDP "v'' connections.

27

1-255

16

Obsolete: Max Local Delay for Interdom CDP to CDP "c" connections.

27

1-64

17

Obsolete: Max Local Delay for Interdom CDP to CDP "t & p" connections.

27

1-255

18

Obsolete: Max Local Delay for Interdom CDP to CDP "a" connections.

27

1-255

19

Obsolete: Max Local Delay for Interdom CDP to CDP High Speed Data connections.

27

1-255

20

Obsolete: Max Local Delay for Interdom High Speed Data connections (in milliseconds).

28

1-255

21

FastPAD De-jitter Buffer Depth (in milliseconds).

15

0-255

22

Number of Consecutive Invalid Login Attempts to Cause Major Alarm.

0

3-9

23

Enable Connection Deroute Delay.

Yes

y or n

24

Frame Relay VCs Polling Rate is the number of minutes between polling cycles for both ATM and Frame Relay virtual connections in the network.

5

5, 10, or 15

25

Port Polling Rate is the is the number of minutes between polling cycles for interval statistics gathered for all ports in the network.

5

5, 10, or 15

Full Name

Configure system parameters

Syntax

cnfsysparm <index> <value>

Related Commands

none

Attributes

Privilege	1
Jobs	Yes
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

cnfsysparm

Description

Configure system-wide parameters. In response to the prompt "Continue" at the bottom of the display enter a "y" or press Return to display the second screen or enter "n" not to display the next screen. If you enter an "n," the prompt line requests an index number.

System Response


sw171          VT    SuperUser       IGX 16    8.5 Oct. 14 1997 17:37 GMT 
 
                           System-Wide Parameters
 
1  Max Time Stamped Packet Age (msec) ................................   32
2  Fail Connections On Communication Break ...........................   No
3  Max Network Delay for 'v' connections (msec).......................   14
4  Max Network Delay for 'c' connections (msec).......................   27
5  Max Network Delay for 't' & 'p' connections (msec).................   14
6  Max Network Delay for 'a' connections (msec).......................   27
7  Max Network Delay for High Speed Data connections (msec)...........   32
8  Max Network Delay for CDP-CDP 'v' connections (msec)...............   32
9  Max Network Delay for CDP-CDP 'c' connections (msec)...............   32
10 Max Network Delay for CDP-CDP 't' & 'p' connections (msec).........   32
11 Max Network Delay for CDP-CDP 'a' connections (msec)..............    32
 
                                                                                
                                                                                
This Command: cnfsysparm                                                        
                                                                                
                                                                                
Continue? n

System Response

In response to the "Continue" prompt at the bottom of the display, enter an "n," then enter a "1" to enter the maximum allowable age for a time-stamped packet.


sw171          VT    SuperUser       IGX 16    8.5 Oct. 14 1997 17:37 GMT 
 
                           System-Wide Parameters
 
1  Max Time Stamped Packet Age (msec) ................................   40
2  Fail Connections On Communication Break ...........................   No
3  Max Network Delay for 'v' connections (msec).......................   14
4  Max Network Delay for 'c' connections (msec).......................   27
5  Max Network Delay for 't' & 'p' connections (msec).................   14
6  Max Network Delay for 'a' connections (msec).......................   27
7  Max Network Delay for High Speed Data connections (msec)...........   32
8  Max Network Delay for CDP-CDP 'v' connections (msec)...............   32
9  Max Network Delay for CDP-CDP 'c' connections (msec)...............   32
10 Max Network Delay for CDP-CDP 't' & 'p' connections (msec).........   32
11 Max Network Delay for CDP-CDP 'a' connections (msec)..............    32
 
 
                                                                                
This Command: cnfsysparm 1
 
 
Enter new value (in Decimal):

Enter the number of the parameter you wish to change, along with the value. For example, to change the Maximum Time-Stamped Packet Age (1) from 40 milliseconds to 42 milliseconds, enter:

: 1 42

Note If you change item 15, the following prompt appears on the screen:

Changing this parameter will reset Frame Relay classes to their defaults. Continue (y/n)?

Changing parameter 15 requires a change in the Frame Relay classes. Since Frame Relay classes are not associated with a specific port (or port speed 0), no translation can be made. The values for Bc and Be, or VC Q depth and PIR are reset to their default values.

Parameter	Description
index	Specifies a numerical value that refers to the specific parameter to be changed. Index numbers and descriptions of the system-wide parameters are in the table that precedes the command summary.
value	Specifies a numerical value that applies to the selected parameter. See Table 13-8.

Table 13-9: cnfsysparm-Parameters

Parameter Description

index

Specifies a numerical value that refers to the specific parameter to be changed. Index numbers and descriptions of the system-wide parameters are in the table that precedes the command summary.

value

Specifies a numerical value that applies to the selected parameter. See Table 13-8.

cnftime

Sets the time for the entire network. The time is broadcast to all nodes in the network. The time displayed at each node is adjusted for the node's time zone. (See the cnftmzn command for more information.) This command can only be executed if the date for the network has already been configured using the cnfdate command. If hour, minute, or second is not entered, the current value is kept.

Full Name

Configure time

Syntax

cnftime <hour> <minute> <second>

Related Commands

cnfdate, cnftmz

Attributes

Privilege	1
Jobs	No
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

cnftime 19 31 00

Description

Configure time to 7:31 in the evening. The system displays two warning prompts before it changes the time.

pubsigx1       TN    SuperUser       IGX 32    8.5       Sep. 5 1997  19:31 GMT
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This Command: cnftime 19 31 00
 
Warning: Changing time of day affects StrataView statistics timestamps
Hit RETURN to change clock, DEL to abort

Parameter	Description
hour	Sets the time for the entire network. The time is broadcast to all nodes in the network. The time displayed at each node is adjusted for the node's time zone. (See the cnftmzn command for more information.) This command can only be executed if the date for the network has already been configured using the cnfdate command. If hour, minute, or second is not entered, the current value is kept.
min	Specifies the current minute. The range is 0-59.
sec	Specifies the current second. The range is 0-59.

Table 13-10: cnftime-Parameters

Parameter Description

hour

Sets the time for the entire network. The time is broadcast to all nodes in the network. The time displayed at each node is adjusted for the node's time zone. (See the cnftmzn command for more information.) This command can only be executed if the date for the network has already been configured using the cnfdate command. If hour, minute, or second is not entered, the current value is kept.

min

Specifies the current minute. The range is 0-59.

sec

Specifies the current second. The range is 0-59.

deluser

Deletes a user from the network. A user can delete users at any lower privilege level.

Full Name

Delete a user

Syntax

deluser <user_id>

Related Commands

adduser, dspusers

Attributes

Privilege	1-5
Jobs	No
Log	Yes
Node	IPX, IGX, BPX
Lock	Yes

Example 1

deluser john

Description

Delete user "john."

alpha          TRM   YourID:1        IPX 16    8.5    Aug. 16 1997 13:52 PST 
                                                                                
YourID       1                                                                  
Sarah        5                                                                  
 
 
 
 
 
 
 
\
 
 
 
 
 
                                                                                
Last Command: deluser John                                                      
                                                                                
                                                                                
Next Command:

Parameter	Description
userid	Specifies the name of the user to delete from the network.

Table 13-11: deluser-Parameters

Parameter Description

userid

Specifies the name of the user to delete from the network.

dspnwip

Displays the IP address for each node in the network. The IP address is used to route TFTP messages transferring bulk statistics between the node and the StrataView Plus Statistics Master.

Full Name

Display network IP interface

Syntax

dspnwip

Related Commands

cnfwip

Attributes

Privilege	1-6
Jobs	No
Log	No
Node	IPX, IGX, BPX
Lock	No

Example 1

dspnwip

Description

Display network IP addresses.


axiom1       TN    bootzilla       IGX 32    8.5       Sep. 5 1997  18:18 GMT
 
Active Network IP Address:             169.134.90.106
Active Network IP Subnet Mask:         255.255.255.0
 
NodeName   IP Address
axiom1   169.134.90.111
         169.134.90.105
         169.134.90.101
axiom2   169.134.90.102
axiom3   169.134.90.103
axiom1   169.134.90.106
 
 
Last Command: dspnwip
 
 
Next Command:

dsppwd

Displays the password of the current user or any user at any lower privilege level.

Full Name

Display password

Syntax

dsppwd <user_id>

Related Commands

adduser, cnfpwd, deluser, dspusers

Attributes

Privilege	1-6
Jobs	No
Log	No
Node	IPX, IGX, BPX
Lock	No

Example 1

dsppwd yourid

Description

Display the password for user YourID.

System Response


alpha          TRM   YourID:1        IPX 16    8.5    Aug. 16 1997 13:56 PST 
                                                                                
                                                                                
                                                                                
The password for YourID is liftoff                                              
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
This Command: dsppwd YourID                                                     
                                                                                
This screen will self-destruct in ten seconds                                   
Next Command: dsppwd YourID

Parameter	Description
userid	Specifies the user whose password is displayed.

Table 13-12: dsppwd-Parameters

Parameter Description

userid

Specifies the user whose password is displayed.

dspsnmp

Display the following SNMP parameters for the current node:

Get Community String
Set Community String
Trap Community String
SNMP Set Request Queue Size
SNMP Queued Request Timeout, in seconds
SNMP Trap Event Queue Size

Full Name

Display SNMP parameters

Syntax

dspsnmp

Related Commands

cnfsnmp, dspsnmpstats

Attributes

Privilege	1-6
Jobs	No
Log	No
Node	IPX, IGX, BPX
Lock	No

Example 1

dspsnmp

Description

Display the SNMP parameters for the current node.

System Response


sw91           TN    SuperUser       IPX 8     8.5       Aug. 29 1997 13:45 GMT
 
Get Community String:                  NOACCESS
Set Community String:                  NOACCESS
Trap Community String:                 NOACCESS
 
SNMP Set Request Queue Size:           110
SNMP Queued Request Timeout (secs):    30
SNMP Trap Event Queue Size:            100
 
 
 
 
 
 
 
 
 
Last Command: dspsnmp
 
 
Next Command:

dspsnmpstats

Displays the following SNMP statistics for the node:

SVC Requests Received, the number of SVC request received.
SVC Current Queue Length, the number of outstanding SVC requests in the queue.
SVC Maximum Queue Length, the high watermark of the number of outstanding SVC requests in the queue.
SVC Requests Timed Out, the number of SVC requests that have timed out.
Current Trap Managers, the number of managers (up to 10) that are currently registered, their IP addresses and UDP ports.
Traps Transmitted, the number of traps transmitted.
TRAP Current Queue Length, the number of outstanding traps in the queue.
TRAP Maximum Queue Length, the high watermark of the number of outstanding traps in the queue.
TRAP Queue Events Discarded, the number of traps discarded due to queue overflow.
Overflow Traps Transmitted, the number of overflow traps transmitted due to queue overflow.

Full Name

Display SNMP parameters

Syntax

dspsnmpstats

Related Commands

cnfsnmp, dspsnmp

Attributes

Privilege	1-6
Jobs	No
Log	No
Node	IPX, IGX, BPX
Lock	No

Example 1

dspsnmpstats

Description

Display SNMP statistics for the current node.

System Response


sw91           TN    SuperUser       IPX 8     8.5       Aug. 29 1997 13:21 GMT
 
SVC Requests Received:       256       Traps Transmitted:            256
 
SVC Current Queue Length:    0         TRAP Current Queue Length:    0
SVC Maximum Queue Length:    0         TRAP Maximum Queue Length:    0
SVC Requests Timed Out:      0         TRAP Queue Events Discarded:  196864
                                       Overflow Traps Transmitted:   100925440
 
Current Trap Managers:       0/10      Snmp_Trap_Db Ptr:             30DDCD02
 
 
 
 
 
 
 
 
Last Command: dspsnmpstats
 
 
Next Command:

dspusers

Displays users. The privilege levels in the display are restricted to those of the current user and any privileges below the current user.

Full Name

Display users

Syntax

dspusers

Related Commands

adduser, deluser, dspusers

Attributes

Privilege	1-6
Jobs	No
Log	No
Node	IPX, IGX, BPX
Lock	No

Example 1

dspusers

Description

Display the users on a network.

dspusertask

Displays information about the current user-task. The displayed information varies with the user task. For example, information about a vt session slightly differs from a telnet session. The command takes a user task number as an argument. If the user task number is unknown, enter the command without a number to see a list of possible user tasks and the current user task. The types of user tasks are as follows:

User, which can be the control terminal user, auxiliary port user, or StrataView
A telnet session
A virtual terminal session (vt)
An SNMP agent
A job

Full Name

Display user task

Syntax

dspusertask [user task number]

Related Commands

adduser, cnfpwd, deluser, dspusers, dsppwd

Attributes

Privilege	1-6
Jobs	No
Log	No
Node	IPX, IGX, BPX
Lock	No

Example 1 step 1

dspusertask

Description

Display user task information—without specifying a task in this case. This example shows a case in which the user has started a vt session on a node. See also step 2 of this example.

System Response


sw78           VT    SuperUser       BPX 15    8.5      Jan. 31 1997 15:52 PST
 
 #  TASK  PURPOSE     USER ID            #  TASK  PURPOSE     USER ID
 -- ---- ------------ -------            -- ---- ------------ -------
 1  USR1 control port none               13 VT-5 VT           none
 2  USR2 auxilry port none               14 VT-6 VT           none
 3  USR3 lan port(SV) none               15 SNMP agent        n/a
 4  TN-1 lan (telnet) none               16 JOBS runs jobs    n/a
 5  TN-2 lan (telnet) none
 6  TN-3 lan (telnet) none
 7  TN-4 lan (telnet) none
 8  TN-5 lan (telnet) none
 9  VT-1 VT: sw81     SuperUser   < You
 10 VT-2 VT           none
 11 VT-3 VT           none
 12 VT-4 VT           none
 
 
This Command: dspusertask
 
 
Please Enter User Number:9

Example 1 step 2

Description

This example shows the screen after the you enter a 9 at the prompt in the previous screen, a case in which you already started a vt session on a node. Note that the display shows the status as a vt slave, and the node on which the vt session originated is sw81.

sw78           VT    SuperUser       BPX 15    8.5      Jan. 31 1997 15:53 PST
 
 
    Task: VT-1
    Logged in as: SuperUser
    VT master:  no
    VT slave:   yes    Master node is: sw81
    VT pending: no
 
    Public  lock: no
    Private lock: none
 
    No command is currently running.
    Previous command: dspusertask 9
 
 
Last Command: dspusertask 9
 
 
Next Command:

Table 13-13: dspusertask-Parameters

Parameter Description

user task number

Specifies the number of the user task whose information is displayed.

dspusertasks

Displays general information about all current user-tasks. The types of user tasks are as follows:

User, which can be the control terminal user, auxiliary port user, or StrataView
A telnet session
A virtual terminal session (vt)
An SNMP agent
A job

Full Name

Display user tasks

Syntax

dspusertasks

Related Commands

adduser, cnfpwd, deluser, dspusers, dsppwd, dspusertask

Attributes

Privilege	1-6
Jobs	No
Log	No
Node	IPX, IGX, BPX
Lock	No

Example 1

dspusertasks

Description

Display user task information.

System Response


sw151          TN    SuperUser       IGX 16    8.5       Aug. 14 1997 18:02 GMT
 
 #  TASK  PURPOSE     USER ID            #  TASK  PURPOSE     USER ID
 -- ---- ------------ -------            -- ---- ------------ -------
 1  USR1 control port SuperUser          13 VT-5 VT           none
 2  USR2 auxilry port none               14 VT-6 VT           none
 3  USR3 lan port(SV) none               15 SNMP agent        n/a
 4  TN-1 lan (telnet) none               16 JOBS runs jobs    n/a
 5  TN-2 lan (telnet) SuperUser   < You
 6  TN-3 lan (telnet) none
 7  TN-4 lan (telnet) none
 8  TN-5 lan (telnet) none
 9  VT-1 VT           none
 10 VT-2 VT           none
 11 VT-3 VT           none
 12 VT-4 VT           none
 
 
Last Command: dspusertasks
 
 
Next Command:

Table of Contents

Managing the Network

Full Name

Syntax

Related Commands

Attributes

Example 1

System Response

Full Name

Syntax

Related Commands

Attributes

Example 1

System Response

Full Name

Syntax

Related Commands

Attributes

Example 1

Full Name

Syntax

Related Commands

Attributes

Example 1

Full Name

Syntax

Related Commands

Attributes

Example 1

Full Name

Syntax

Related Commands

Attributes

Example 1

System Response

System Response

Full Name

Syntax

Related Commands

Attributes

Example 1

Full Name

Syntax

Related Commands

Attributes

Example 1

Full Name

Syntax

Related Commands

Attributes

Example 1

Description

Full Name

Syntax

Related Commands

Attributes

Example 1

System Response

Full Name

Syntax

Related Commands

Attributes

Example 1

System Response

Full Name

Syntax

Related Commands

Attributes

Example 1

System Response

Full Name

Syntax

Related Commands

Attributes

Example 1

Full Name

Syntax

Related Commands

Attributes

Example 1 step 1