Cisco VPN 3002 Hardware Client Quick Start, Release 4.0 (online viewing)

These instructions explain how to install and configure the Cisco VPN 3002 using default values.

How to Start

At the central-site Concentrator, configure the connection as a client, NOT LAN-to-LAN. See "Settings on the VPN 3000 Series Concentrator" section.

Client Mode or Network Extension Mode?

The VPN 3002 operates in either Client—also called Port Address Translation (PAT)—mode or Network Extension mode. A summary of the differences follows:

Client/PAT Mode (the default)	Network Extension Mode
Easier to configure.	Two more steps to configure than Client mode.
All traffic from the VPN 3002 private network arrives on the private network of the central-site VPN Concentrator with a single source-IP address.	You must assign an IP address other than the default to the VPN 3002 private interface, and you must disable PAT mode.
The IP addresses of the computers on the VPN 3002 private network are hidden. You cannot ping or access a device on the VPN 3002 private network from the central site. But you can access the assigned IP address of the VPN 3002 from the central site.	Devices behind the VPN Concentrator have direct access to devices on the VPN 3002 private network only through the tunnel. You can ping or access a device on the VPN 3002 network from the central site.
VPN 3002 initiates tunnel, and always sends data before receiving data.	VPN 3002 initiates tunnel. Central site can send data first, but only if split-tunneling is disabled.
Some applications are incompatible with PAT mode.

Using Default Values to Configure the VPN 3002

For the simplest configuration, Client/PAT mode, accept default values for all parameters that have defaults. Use the Quick Configuration menu; you can set parameters in any order. Your changes become the running configuration as soon as you make them, and the system automatically saves your changes at the Done screen.

For Either Client or Network Extension Mode

2. Configure an IP address on the public interface. If you use DHCP to obtain an IP address for the public interface, your ISP may require a hostname. Enter this hostname in the Public Interface parameter.

For Network Extension Mode You Must Also

1. Change the IP address of the private interface (Private Interface parameter).

Settings on the VPN 3000 Series Concentrator

2. Assign this VPN 3002 to a group. Configure group and user names and passwords. These must match the group and user names and passwords that you set on the VPN 3002.

3. If the VPN 3002 uses Client mode, enable a method of address assignment for the VPN 3002: DHCP, address pools, address from authentication server, or client specified.

Be sure that the subnet behind the VPN 3002 is routable from private networks behind the VPN Concentrator. You can use Reverse Route Injection on the VPN Concentrator if its private network uses RIP or OSPF, or you can configure a static route.
Check the box in the Allow Network Extension Mode parameter for the group to which the VPN 3002 belongs (HW Client tab).

Installing the VPN 3002

1. Use a LAN cable to connect the VPN 3002 public interface to your public network device or Ethernet hub or switch.

2. Connect the power cable between the VPN 3002 and a reliably grounded power outlet.

3. Configure the VPN 3002 using one of the following: a browser,
console port, Telnet, or SSH.

Using a Browser to Configure the VPN 3002

1. Use a LAN cable to attach a PC to the private interface (3002) or switch port (3002-8E) .

2. Enter the default IP address (192.168.10.1) in the browser Location or Address field.

3. At the VPN 3002 Login prompt, enter the login name admin and the default password admin. Click Login.

4. In the Main window, select Quick Configuration from the menu. Follow the online instructions for all subsequent screens. Note that to configure Network Extension mode, you must change the private interface IP address and disable PAT.

5. Click Help for context-sensitive online help. When you click Help, you also reach links for an online Quick Configuration guide that supplements this Quick Start card, and an online Cisco VPN 3002 Reference publication. These documents are available only online.

Using a Console Port to Configure the VPN 3002

1. Connect the RJ-45 serial cable to the console port on the back of the VPN 3002 to the COM1 or another serial port on the PC.

2. Configure a connection to COM1 with settings of 9600 bps, 8 data bits, No parity, 1 stop bit, and hardware flow control.

3. After the initialization and boot messages complete, press Enter until you see a login prompt. Enter the login name, admin, and the default password admin. Press Return.

5. Follow the online instructions for subsequent parameters. Be sure that your entries conform to the formats for current values, displayed in brackets after the prompt. Note that to configure Network Extension Mode, you must change the private interface IP address and disable PAT.

Using Telnet or SSH to Configure the VPN 3002

2. Follow Steps 3-5 in the "Using a Console Port to Configure the VPN 3002" section of this card.

LEDs on Front of Unit
LED	State	Explanation
PWR	green	Unit is on and has power.
	off	Unit is powered off.
SYS	flashing amber	Unit is performing diagnostics.
	solid amber	Unit has failed diagnostics.
	flashing green	DHCP or PPPoE negotiations in process.
	green	Unit is operational.
VPN	off	No VPN tunnel exists.
	amber	Tunnel has failed.
	green	Tunnel is established.

LEDs on Private and Public Interface Ports
Green	The interface is connected to the network.
Flashing amber	Data is traveling across the network.

What's Next?

You can configure the system in more detail. In the Main screen of the HTML interface, select Configuration > Interfaces. You can explore the VPN 3002 Administration and Monitoring functions, also from the Main screen.

For more information, see the Cisco VPN 3002 Getting Started and Reference publications. Also go to www.cisco.com, and click the Service and Support section. Find world-wide phone numbers for the Technical Assistance Center at http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.

Copyright © 2003 Cisco Systems, Inc. All rights reserved. Cisco, Cisco IOS, Cisco Systems, and the Cisco Systems logo are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries. All other brands, names, or trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0201R)

Table of Contents