|
|
The VPN 3002 Hardware Client Command Line Interface (CLI) is a menu- and command-line-based configuration, administration, and monitoring system built into the VPN 3002. You use it via the system console or a Telnet (or Telnet over SSL) session.
You can use the CLI to completely manage the system. You can access and configure the same parameters as the HTML-based VPN 3002 Hardware Client Manager.
This chapter describes general features of the CLI and how to access and use it. It does not describe the individual menu items and parameter entries. For information on specific parameters and options, see the corresponding section of the Manager in this manual. For example, to understand Ethernet interface configuration parameters and choices, see Configuration | Interfaces | Private/Public in "Interfaces".
You can access the CLI in two ways: via the system console or a Telnet (or Telnet over SSL) client.
To access the CLI via console:
1. Connect a PC to the VPN 3002 via an RJ-45 serial cable (which Cisco supplies with the system) between the Console port on the VPN 3002 and the COM1 or serial port on the PC. For more information, see the VPN 3002 Hardware Client Getting Started manual.
2. Start a terminal emulator (e.g., HyperTerminal) on the PC. Configure a connection to COM1 with port settings of:
3. Press Enter on the PC keyboard until you see the login prompt. (You may see a password prompt and error messages as you press Enter; ignore them and stop at the login prompt.)
Login: _
To access the CLI via a Telnet or Telnet/SSL client:
1. Enable the Telnet or Telnet/SSL server on the VPN 3002. (They are both enabled by default on the private network.) See the Configuration | System | Management Protocols | Telnet screen on the Manager.
2. Start the Telnet or Telnet/SSL client, and connect to the VPN 3002 using these parameters:
10.10.147.23. The VPN 3002 displays a login prompt.
Login: _
You start the CLI by logging in.
CLI login usernames and passwords for both console and Telnet access are the same as those configured and enabled for administrators. See the Administration | Access Rights | Administrators screen. By default, only admin is enabled.
This example uses the factory-supplied default admin login and password. If you have changed them, use your entries.
At the prompts, enter the administrator login name and password. Entries are case-sensitive.
Login: admin
Password: admin (The CLI does not show your entry.)
The CLI displays the opening welcome message, the main menu, and the Main -> prompt.
Welcome to
Cisco Systems
VPN 3002 Hardware Client
Command Line Interface
Copyright (C) 1998-2001 Cisco Systems, Inc.
1) Configuration
2) Administration
3) Monitoring
4) Save changes to Config file
5) Help Information
6) Exit
Main -> _
This section explains how to:
The CLI displays menus or prompts at every level to guide you in choosing configurable options and setting parameters. The prompt always shows the menu context.
To use the CLI, enter a number at the prompt that corresponds to the desired menu item, and press Enter.
For example, this is the Configuration > System > General > System Identification menu:
1) Set System Name
2) Set Contact
3) Set Location
4) Back
General -> _
Enter 1 to set the system name.
The CLI shows any current or default value for a parameter in brackets [ ]. To change the value, enter a new value at the prompt. To leave the value unchanged, just press Enter.
Continuing the example above, this is the prompt to enter a value for the system name:
> Host Name
General -> [ Lab VPN ] _
You can enter a new name at the prompt, or just press Enter to keep the current name.
There are two ways to move quickly through the CLI: shortcut numbers, and the Back/Home options. Both ways work only when you are at a menu, not when you are at a value entry.
When you become familiar with the structure of the CLI—which parallels the HTML-based VPN 3002 Hardware Client Manager—you can quickly access any level by entering a series of numbers separated by periods. For example, suppose you want to change the Access Rights for Administrators. The series of menus that gets to that level from the main menu is:
Main -> _
1) Configuration
2) Administration
3) Monitoring
4) Save changes to Config file
5) Help Information
6) Exit
Main -> 2 (Administration)
) Software Update
2) System Reboot
3) Ping
4) Access Rights
5) File Management
6) Certificate Management
7) Back
Config -> 4 (Access Rights)
1) Administrators
2) Access Settings
3) Back
Admin -> 1
Administrative Users
------------------------
Username Enabled
------------------------
admin Yes
config No
isp No
------------------------
1) Modify Administrator
2) Back
Admin -> 1
> Which Administrator to Modify
Admin ->
As a shortcut, you can just enter 2.4.1.1 at the Main-> prompt, and move directly to the Modify Administrators menu:
1) Configuration
2) Administration
3) Monitoring
4) Save changes to Config file
5) Help Information
6) Exit
Main -> 2.4.1.1
> Which Administrator to Modify
Admin ->
 |
Note At this last prompt, you cannot use a number shortcut. At this prompt, you must type in the name of
the administrator you want to modify, for example, config.
|
Admin -> config
The prompt always shows the current context in the menu structure.
Most menus include a numbered Back choice. Instead of entering a number, you can just enter b or B to move back to the previous menu.
Also, at any menu level, you can just enter h or H to move home to the main menu.
To display a brief help message, enter 5 at the main menu prompt. The CLI explains how to navigate through menus and enter values. This help message is available only at the main menu.
Cisco Systems. Help information for the Command Line Interface
From any menu except the Main menu.
-- 'B' or 'b' for Back to previous menu.
-- 'H' or 'h' for Home back to the main menu.
For Data entry
-- Current values are in '[ ]'s. Just hit 'Enter' to accept value.
1) View Help Again
2) Back
Help -> _
To return to the main menu from this help menu, enter h (for home), or 2 or b (for back) at the prompt.
Configuration and administration entries take effect immediately and are included in the active, or running, configuration. However, if you reboot the VPN 3002 without saving the active configuration, you lose any changes.
To save changes to the system configuration (CONFIG) file, navigate to the main menu. At the prompt, enter 4 for Save changes to Config file.
1) Configuration
2) Administration
3) Monitoring
4) Save changes to Config file
5) Help Information
6) Exit
Main -> 4
The system writes the active configuration to the CONFIG file and redisplays the main menu.
To stop the CLI, navigate to the main menu and enter 6 for Exit at the prompt:
1) Configuration
2) Administration
3) Monitoring
4) Save changes to Config file
5) Help Information
6) Exit
Main -> 6
Done
Make sure you save any configuration changes before you exit from the CLI.
What you see and can configure with the CLI depends on administrator access rights. If you don't have permission to configure an option, you see -), rather than a number, in menus.
For example, here is the main menu for the default Monitor administrator:
-) Configuration
-) Administration
3) Monitoring
-) Save changes to Config file
5) Help Information
6) Exit
Main -> _
The default Monitor administrator can only monitor the VPN 3002, not configure system parameters or administer the system.
See Administration | Access Rights | Administrators in "Administration", for more information.
This section shows all the menus in the first three levels below the CLI main menu. (There are many additional menus below the third level; and within the first three levels, there are some non-menu parameter settings. To keep this chapter at a reasonable size, we show only the menus here.)
The numbers in each heading are the keyboard shortcut to reach that menu from the main menu. For example, entering 1.3.1 at the main menu prompt takes you to the Configuration > System Management> IP Routing menu.
|
Note The CLI menus and options—and thus the keyboard shortcuts—may change with new software versions. Please check familiar shortcuts carefully when using a new release. |
1) Configuration
2) Administration
3) Monitoring
4) Save changes to Config file
5) Help Information
6) Exit
Main -> _
1) Quick Configuration
2) Interface Configuration
3) System Management
4) Policy Management
5) Back
Config -> _
See the VPN 3002 Hardware Client Getting Started guide for complete information about Quick Config.
This table shows current IP addresses.
.
.
1) Configure the Private Interface
2) Configure the Public Interface
3) Back
Interfaces -> _
1) Enable/Disable
2) Set IP Address
3) Set Subnet Mask
4) Select Ethernet Speed
5) Select Duplex
6) Back
Private/Public Interface -> _
1) Servers (DNS)
2) Tunneling Protocols (IPSec)
3) IP Routing (static routes, etc.)
4) Management Protocols (Telnet, HTTP, etc.)
5) Event Configuration
6) General Config (system name, time, etc.)
7) Back
System -> _
1) DNS Servers
2) Back
Servers -> _
1) DNS Servers
2) Back
Tunnel -> _
1) Static Routes
2) Default Gateway
3) DHCP
4) DHCP Options
5) Back
Routing -> _
1) Configure HTTP/HTTPS
2) Configure Telnet
3) Configure SNMP
4) Configure SNMP Community Strings
5) Configure SSL
6) Configure SSH
7) Back
Network -> _
1) General
2) Classes
3) Trap Destinations
4) Syslog Servers
5) Back
Event -> _
1) System Identification
2) System Time and Date
3) Back
General -> _
1) Traffic Management
2) Back
Policy -> _
1) Port Address Translation (PAT)
2) Back
Traffic -> -
1) Software Update
2) System Reboot
3) Ping
4) Access Rights
5) File Management
6) Certificate Management
7) Back
Admin -> _
Name of the file for main code upgrade? [phoenix3002dc.bin]
IP address of the host where the file resides? [10.10.66.10]
(M)odify any of the above (C)ontinue or (E)xit? [M]
1) Cancel Scheduled Reboot/Shutdown
2) Schedule Reboot
3) Schedule Shutdown
4) Back
Admin -> _
1) Save active Configuration and use it at Reboot
2) Reboot without saving active Configuration file
3) Reboot ignoring the Configuration file
4) Back
Admin -> _
1) Save active configuration and use it at next reboot
2) Shutdown without saving active Configuration file
3) Shutdown, ignoring the Configuration file at next reboot
4) Back
Admin -> _
> Ping host
Admin ->
1) Administrators
2) Access Settings
3) Back
Admin -> _
Admin -> 1
Administrative Users
------------------------
Username Enabled
------------------------
admin Yes
config No
isp No
------------------------
1) Modify Administrator
2) Back
Admin ->
1) Set Session Timeout
2) Set Session Limit
3) Enable/Disable Encrypt Config File
4) Back
Admin -> _
List of Files
-------------
CONFIG CONFIG.BAK
1) View Config File
2) Delete Config File
3) View Backup Config File
4) Delete Backup Config File
5) Swap Config Files
6) Upload Config File
7) Back
File -> _
Every time the active configuration is saved,...
.
.
.
1) Swap
2) Back
Admin -> _
1) Enrollment
2) Installation
3) Certificate Authorities
4) Identity Certificates
5) SSL Certificate
6) Back
Certificates -> _
1) Install Certificate Authority
2) Install SSL Certificate (from Enrollment)
3) Install SSL Certificate (with private key)
4) Install Identity Certificate (from Enrollment)
5) Back
Certificates -> _
Certificate Authorities
.
.
.
1) View Certificate
2) Delete Certificate
4) Back
Certificates -> _
Identity Certificates
.
.
.
1) View Certificate
2) Delete Certificate
3) Back
Certificates -> _
Subject
.
.
'q' to Quit, '<SPACE>' to Continue ->
.
Issuer
.
.
'q' to Quit, '<SPACE>' to Continue ->
.
Serial Number
.
.
1) Delete Certificate
2) Generate Certificate
3) Back
Certificates -> _
1) Routing Table
2) Event Log
3) System Status
4) General Statistics
5) Back
Monitor -> _
Routing Table
.
.
'q' to Quit, '<SPACE>' to Continue ->
.
.
1) Refresh Routing Table
2) Clear Routing Table
3) Back
Routing -> _
1) Configure Log viewing parameters
2) View Event Log
3) Clear Log
4) Back
Log -> _
[Event Log entries]
.
.
.
1) First Page
2) Previous Page
3) Next Page
4) Last Page
5) Back
Log -> _
System Status
.
.
.
1) Refresh System Status
2) Connect Now
3) Disconnect Now
4) Back
Status -> _
Card Status -> _
1) Protocol Statistics
2) Server Statistics
3) MIB II Statistics
4) Back
General -> _
1) IPSec Statistics
2) HTTP Statistics
3) Telnet Statistics
4) DNS Statistics
5) More
6) Back
General -> _
1) DHCP Statistics
2) Back
General -> _
1) Interface-based
2) System-level
3) Back
MIB2 -> _
Posted: Tue Nov 19 15:17:51 PST 2002
Copyright 1989-2000©Cisco Systems Inc.