cc/td/doc/product/software/ios113ed
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Release Notes for Release 4.2(3) Feature Packs for
Cisco 700 Series Routers

Release Notes for Release 4.2(3) Feature Packs for
Cisco 700 Series Routers

September 21, 1998

These release notes describe the Cisco 700 Router software Release 4.2(3) feature packs. Table 1 lists the Cisco product numbers for the supported feature packs:


Table 1: Feature Pack Product Numbers

CD076-IRX-4.2=

Cisco 760/770 Series Internet Ready with X.25 over B&D Feature Pack Release 4.2.3

CD076-ROX-4.2=

Cisco 760/770 Series Remote Office with X.25 over B&D Feature Pack Release 4.2.3

Contents

These release notes discuss the following topics:

System Support

Cisco 700 series router software Release 4.2(3) supports the following routers:

Cisco 760 Series Cisco 770 Series

Cisco 761-CH

Cisco 771-CH

Cisco 762-CH

Cisco 772-CH

Cisco 765-CH

Cisco 775-CH

Cisco 766-CH

Cisco 776-CH

Cisco Feature Packs and Memory Requirements

This section explains the following:

What Is a Feature Pack?

The heart of the Release 4.2(3) software feature pack for Cisco 700 series routers is a software image stored on CD-ROM. The feature pack box contains the following:

Release 4.2(3) Feature Pack Descriptions and Memory Requirements

Table 1 in this section identifies each feature pack as specified on the router software CD-ROM label and describes the feature sets in each feature pack. The table also lists the following: UNIX and DOS filenames of the images, router platform on which each feature set runs, and memory requirements for each feature set.

Images for software Release 4.0(1) and higher require 1.5 MB of dynamic RAM (DRAM). If you do not have enough DRAM to support the software, the router does not boot. Refer to the "National ISDN Capability Packages" section for instructions on checking the amount of DRAM. Instructions for increasing the amount of DRAM are in the Cisco 700 Series Installation Guide.

X.25 images require 1.5 MB of DRAM and 1 MB of Flash memory. If your router does not have enough Flash memory to run X.25 images, you must replace it with a Cisco 700M series router. The label on the bottom of the router identifies an M-series router. You can display the amount of Flash memory by using the version command. Refer to the Cisco 700 Series Command Reference for information about this command.


Table 2: Cisco Feature Pack Image Filenames and Memory Requirements
Product Number CD-ROM Title Image Name (UNIX) Image Name (DOS) Flash Memory Required Main Memory Required RSL Installer Description

CD076-IRX-4.2=

Cisco 760/770 Series
Internet Ready with X.25 over B&D
Feature Pack
Release 4.2.3

c760-in.b-1TR6.42-3.bin

80250303

.5 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing Feature Set for Germany

c760-in.b-INS.42-3.bin

80250203

.5 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing Feature Set for Japan

c760-in.b-NET3.42-3.bin

80250103

.5 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing Feature Set for Europe

c760-in.b-TPH.42-3.bin

80250003

.5 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing Feature Set for Australia

c760-in.b-US.42-3.bin

80349903

.5 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing Feature Set for US

c760-in.b-MLS.42-3.bin

80250903

.5 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing Feature Set for Malaysia

c760-in.bxd-NET3.42-3.bin

80249803

1 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing, X.25/B& D Feature Set for Europe

c760-in.bxd-US.42-3.bin

80249603

1 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing, X.25/B& D Feature Set for US

c760-in.bxd-MLS.42-3.bin

80250703

1 MB

1.5 MB

760/770 Series Internet Ready 30 users, IP routing, X.25/B& D Feature Set for Malaysia

CD076-ROX-4.2=

Cisco 760/770 Series
Remote Office with X.25 over B&D
Feature Pack
Release 4.2.3

c760-in.r-1TR6.42-3.bin

80249503

.5 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX Feature Set for Germany

c760-in.r-INS.42-3.bin

80249403

.5 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX Feature Set for Japan

c760-in.r-NET3.42-3.bin

80249303

.5 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX Feature Set for Europe

c760-in.r-TPH.42-3.bin

80249203

.5 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX Feature Set for Australia

c760-in.r-US.42-3.bin

80249103

.5 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX Feature Set for US

c760-in.r-MLS.42-3.bin

80250803

.5 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX Feature Set for Malaysia

c760-in.rxd-NET3.42-3.bin

80249003

1 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX, X.25/B & D for Europe

c760-in.rxd-US.42-3.bin

80248803

1 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX, X.25/B & D for US

c760-in.rxd-MLS.42-3.bin

80250603

1 MB

1.5 MB

760/770 Series RO 1500 users, data comp, IP/IPX, X.25/B & D for Malaysia


Note Internet Ready images do not support IPX routing.

Memory Requirements for Running X.25

Running X.25 over the ISDN D channel requires 1 MB of Flash memory on a Cisco 700 router. If your router has a Flash memory size of 0.5 MB and you plan to run X.25 over the ISDN D channel, contact your Cisco Sales Representative to trade in your Cisco 700 router.

Cisco 700 Software Release 4.2(3) Enhancements

The Cisco 700 series router software Release 4.2(3) provides the following enhancements:

Increased Number of Users

In the IR image for software Release 4.2(3), the number of users allowed is increased to 30.

ISDN BRI Sends Alert

Some network equipment requires that the router send an alert message. In software Release 4.2(3), the Cisco 700 series router sends an alert message when answering a call. (CSCdk26667)

Cisco 700 Software Release 4.2(3) Known Limitations

This section provides the latest information about Cisco 700 series router software Release 4.2(3) limitations. Each item includes the Cisco DDTS tracking number, if applicable.

During the upload of a configuration over ISDN the line, the DEMAND 1 DURATION statement is missed. This has been resolved in software Release 4.2(3). (CSCdj80519)

In the 1tr6 image, if you are connected on a voice call and flash, the message "Warning: Illegal dereference" displays and the router might reboot. This has been resolved in software Release 4.2(3). (CSCdk03329)

The Cisco 700 series router telnet server does not give up by timeout. The router calls the Telnet client every 2 minutes and does not stop. The condition is created as follows:

This has been resolved in software Release 4.2(3). (CSCdk11798)

AO/DI is available only on one connection. Even if it is enabled on multiple profiles, only one profile at a time can use it. (no number available)

When TAS mode is on, the Cisco 700 series router continuously attempts to authenticate after a failed login. For example, a user launches a Web browser but does not enter a login ID. The connection to the CiscoSecure Authentication Agent times out (as it should); however, the router continues to retry the connection. During the subsequent retries, the router sends its own authentication information, not the authentication information of the user. This results in sessions going up and down continuously. This has been resolved in software Release 4.2(3). (CSCdk24138)

Loading the Software

To save the router configuration file on your PC, load new software, and then reload the configuration to the router, refer to the "Getting Started with Cisco 700 Series Software" CD booklet shipped with your software feature pack.

The default image for Cisco 761, Cisco 765, Cisco 771, and Cisco 775 routers is NET3, IR. The default image for all other Cisco 700 series routers is U.S.

Setting Switch Types

This section describes how to configure your router to operate with the network central office switch. Table 3 describes each switch type. The default switch type is dependent upon the system software version.


Note Not all switch settings are available to all users. The switch-type settings available depend on the type of software loaded into the router.

Table 3:
Switch Type Description

5ess

AT&T 5ESS

dms

Northern Telecom DMS-100

ni-1

National ISDN-1

ins

Japan—NTT's Information Network System

net3

Europe (also some areas in Asia)—ISDN BRI standard

1tr6

Germany—ISDN BRI standard

tph

Australia

perm64

Dedicated line service. Enables the unit to use a single 64-kbps data stream connected to one port. Channel 1 runs at 64 kbps, and channel 2 is not used. In Japan, NTT's super Digital service is the ISDN example of a leased line server.

perm128

Dedicated line service. Enables the unit to use a single 128-kbps data stream connected to one port. Channels 1 and 2 are combined to run at 128 kbps. In Japan, NTT's HSD service is an example.

Switch Types

To configure your router to operate with the network central office switch, use the command set switch from the system level command mode. The following example configures the ISDN switch type as DMS:

Host> set switch dms

Table 4 lists the commands available to use for each switch type and location:


Table 4:
Switch Type Location Command to Set the Switch Type

5ess, dms, ni-1

U.S.

SEt SWitch {5Ess | DMS | NI-1 | PERM64 | PERM128}

ins

Japan

SEt SWitch {INS | PERM64 | PERM128}

net3

Europe

SEt SWitch {NET3 | PERM64 | PERM128}

1tr6

Germany

SEt SWitch {lTR6 | PERM64 | PERM128}

tph

Australia

SEt SWitch {TPH | PERM64 | PERM128}

perm64, perm128

U.S., Japan, Europe, Germany, Australia

SEt SWitch {PERM64 | PERM128}

Setting Switch Types

Cisco 700 Software Release 4.2(3) Caveats

This section provides the latest information about Cisco 700 series router software Release 4.2(3) caveats. Each item includes the Cisco DDTS tracking number, if applicable.

Windows NT clients fail to browse for a Windows NT server as a result of the following condition:

In software Release 4.2(3), the Cisco 700 series router checks the IPX destination network field in the NetBIOS packet. If the network number field is not zero, the router changes the field to zero and forwards the packet to the LAN. (CSCdk20359)

RIP updates keep the ISDN link up if the idle timeout is greater than the RIP timer value, even if the RIP option is linkup. However, it does not cause the link to come up by itself. To correct the problem, use a filter for RIP traffic with the ignore option in the WAN profile. (no number available)

The system password is echoed over the ISDN connection the first time the connection is established. However, it is not echoed in subsequent connections. (no number available)

The upload command does not include the set ip route destination 0.0.0 propagate off conv1 command in the configuration if a default route was entered in the user-defined profile before the connection was made. This occurs when the router connects to an Internet service provider, and obtains an IP address through IP control protocol (IPCP) negotiation. (no number available)

A router repeatedly receives voice calls when both B channels are occupied with data calls intermittently loses one of the B channels. To correct the problem, reboot the router. (CSCdj68840)

Related Applications

This section describes the applications supported by the Cisco 700 series router software Release 4.2(3).

CiscoSecure Authentication Agent Support

The CiscoSecure Authentication Agent (available for Windows 95 and Windows NT 4.0) application simplifies the use of token authentication over ISDN. There are two authentication modes: single authentication and double authentication.

The Cisco 700 series router operates in single authentication mode when Token Authentication Support (TAS) is enabled. CiscoSecure Authentication Agent is available on the World Wide Web (WWW). See the "Cisco Connection Online" section in this document for more information.

Fast Step Support

Cisco 700 series router software Release 4.0(1) and higher supports Cisco 700 Fast Step. Cisco 700 Fast Step simplifies the setup, configuration, and monitoring of Cisco 700 series routers.

Cisco 700 Fast Step runs on Microsoft Windows 95 and Windows NT 4.0 systems. It is provided with your router on the Cisco Fast Step CD-ROM. The application is also available on Cisco Connection Online. See the "Cisco Connection Online" section in this document for more information.

National ISDN Capability Packages

A capability package is a set of standardized BRI line features that simplifies the process of configuring an ISDN line. The capability package ordering codes described in this section apply to NI1.


Note The Cisco 765, Cisco 766, Cisco 775, and the Cisco 776 require two SPIDs for the analog telephone ports to operate correctly.

Capability Package S

Package S provides alternate voice and circuit-switched data with no additional features. When a minimum feature set is needed, Package S is the preferred NI1 capability package for Cisco 765, Cisco 766, Cisco 775, and Cisco 776 routers.

Capability Package EZ-1 or U

Package EZ-1 (also referred to as Capability Package U) provides alternate voice and circuit-switched data with all the features and capabilities of the router enabled. Package EZ-1 is the preferred NI1 capability package for the Cisco 765, Cisco 766, Cisco 775, and Cisco 776 routers. The features include flexible calling (conference calling, call transfer, hold and retrieve), ACO (call waiting), and Call Forward Busy (CFB).


Note The 5ESS Custom does not support multiple directory numbers per SPID.

If you have any problems with your NI1 provisioning, contact Cisco ISDN Support Services (United States only). To access this service or to obtain more information, call (800) 553-NETS (6387) and select the Customer Service option, or visit the Cisco ISDN web site at www.cisco.com/isdn.

When provisioning multiple directory numbers for a NI1, additional provisioning information that activates the distinctive ringing feature is available from Cisco ISDN Support Services; however, the flexible calling features (three-way conference calling call transfer, hold and retrieve) are not available.

ISDN Support Services

ISDN Support Services are only available in the United States. To access this service or to obtain more information, call 800 553-NETS (6387) and select the Customer Service option, or visit the Cisco ISDN Web site at www.cisco.com/isdn.

Related Documentation

All documents mentioned in this section are available in electronic format. (See the section "Online Navigation" section for more information on accessing electronic documentation.)

The following documentation is related to these release notes:

Cisco 700 Series Router Documentation

The following documentation is provided with your Cisco 700 series router:

Document Additions and Corrections

This section provides information that was not included in the current documentation and is not available elsewhere. The information will be included in the next revision of the documentation.

Turn Bridging Off to Reduce Costs

The Cisco 700 series router attempts to establish a connection with the remote host whenever interesting traffic is queued to be sent over a WAN connection. When bridging is off, the router attempts to connect to the remote device when IP traffic is queued. When bridging is on (default), the router attempts to connect when IP traffic and all nonrouted traffic is queued.

It is recommended that bridging be set to off in a WAN profile to reduce the amount of interesting traffic, and therefore, the number of attempts made to establish a connection. If the remote connection goes down, the router continuously attempts to bring up the line. In some environments (most commonly Windows NT using only Netbios), this causes the line to dial continuously. Depending on your configuration and how your connection is billed, turning bridging off in the WAN profile might reduce your costs.

For example, in the configuration titled "Routing IP On Demand," which begins on page 3-16 of the Cisco 700 Series Installation Guide (DOC-78241=), you should enter the command set bridge off near Step 11. The exact sequence of this command in relation to the other commands is not critical, as long as it is done in the central902 profile.

Software Configuration Tips on the Cisco TAC Home Page

The following URL contains links to access helpful tips to configure your Cisco products:

http://www.cisco.com/kobayashi/serv_tips.shtml

This URL is subject to change without notice. If it does change, point your web browser to http://www.cisco.com/ and follow this path: (button on left margin).

"Hot Tips" are popular tips and hints gathered from Cisco's Technical Assistance Center (TAC). Most of these documents are also available from the TAC's Fax-on-Demand service. To access Fax-on-Demand and receive documents at your fax machine, call 888-50-CISCO (888-502-4726). From international areas, call 650-596-4408.

The following sections are provided from the Technical Tips page:

Online Navigation

Cisco 700 router documentation is available as printed manuals and electronic documents. You can access Cisco 700 router documentation at Cisco Connection Online (CCO) on the World Wide Web and on the Cisco Documentation CD-ROM:

Additional information about CCO and the Documentation CD-ROM is in the sections
"Cisco Connection Online" and "Documentation CD-ROM."

Cisco Connection Online

Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.

CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.

You can access CCO in the following ways:

For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.


Note If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco's Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.

Documentation CD-ROM

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.

If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar, select Documentation, and click Enter the feedback form. After you complete the form, click Submit to send it to Cisco. We appreciate your comments



hometocprevnextglossaryfeedbacksearchhelp
Posted: Tue Sep 3 18:23:33 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.