ISO CLNS Commands

This chapter describes the function and displays the syntax of each ISO CLNS command. For more information about defaults and usage guidelines, see the corresponding chapter of the Router Products Command Reference publication.

Use the area-password router configuration command to configure the area authentication password. The no form of this command disables the password.

Use the clear clns cache EXEC command to clear and reinitialize the CLNS routing cache.

Use the clear clns es-neighbors EXEC command to remove ES neighbor information from the adjacency database.

Use the clear clns is-neighbors EXEC command to remove IS neighbor information from the adjacency database.

Use the clear clns neighbors EXEC command to remove CLNS neighbor information from the adjacency database.

Use the clear clns route EXEC command to remove all of the dynamically derived CLNS routing information.

Use the clns access-group interface configuration command to filter transit CLNS traffic going either into or out of the router or both on a per-interface basis. Use the no form of this command to disable filtering of transit CLNS packets.

name	Name of the filter set or expression to apply.
in	(Optional) Filter should be applied to CLNS packets entering the router.
out	(Optional) Filter should be applied to CLNS packets leaving the router. If you do not specify an in or out keyword, out is assumed.

Use the clns adjacency-filter interface configuration command to filter the establishment of CLNS end system (ES) and intermediate system (IS) adjacencies. Use the no form of this command to disable this filtering.

es	End system adjacencies are to be filtered.
is	Intermediate system adjacencies are to be filtered.
name	Name of the filter set or expression to apply.

Use the clns checksum interface configuration command to enable checksum generation when ISO CLNS routing software sources a CLNS packet. Use the no form of this command to disable checksum generation.

Use the clns cluster-alias interface configuration command to allow multiple systems to advertise the same system ID as other systems in end-system hello messages. The no form of this command disables cluster aliasing.

Use the clns configuration-time global configuration command to specify the rate at which ES hellos (ESHs) and IS hellos (ISHs) are sent. You can restore the default value by specifying the no form of this command.

Use the clns congestion-threshold interface configuration command to set the congestion experienced bit if the output queue has more than the specified number of packets in it. A number value of zero or the no form of the command prevents this bit from being set. Use the no form of this command to remove the parameter setting and set it to 0.

Use the clns dec-compatible interface configuration command to allow ISHs sent and received to ignore the N-selector byte. Use the no form of this command to disable this feature.

Use the clns enable interface configuration command if you do not intend to perform any static or dynamic routing on an interface, but intend to pass ISO CLNS packet traffic to end systems. Use the no form of this command to disable ISO CLNS on a particular interface.

Use the clns erpdu-interval interface configuration command to determine the minimum interval time, in milliseconds, between error PDUs (ERPDUs). A milliseconds value of zero or the no form of this command turns off the interval and effectively sets no limit between ERPDUs.

Use the clns esct-time interface configuration command to supply an ES Configuration Timer (ESCT) option in a transmitted IS hello packet that tells the end system how often it should transmit ES hello packet protocol data units (PDUs). Use the no form of this command to restore the default value and disable this feature.

Use the clns es-neighbor interface configuration command to list all end systems that will be used when you manually specify the NSAP-to-SNPA mapping. The SNPAs are the MAC addresses. Use the no form of this command to delete the ES neighbor.

clns filter-expr ename term
clns filter-expr ename not term
clns filter-expr ename term or term
clns filter-expr ename term and term
clns filter-expr ename term xor term
no clns filter-expr ename

Use one or more clns filter-expr global configuration commands to combine CLNS filter sets and CLNS address templates into complex logical NSAP pattern-matching expressions. The no form of this command deletes the expression. There are many forms of this command.

ename

Alphanumeric name to apply to this filter expression.

term

Filter expression term. A term can be any of the following:

ename—Another, previously defined, filter expression.

sname (or destination sname)—A previously defined filter set name, with the filter set applied to the destination NSAP address.

source sname—A previously defined filter set name, with the filter set applied to the source NSAP address.

Use one or more clns filter-set global configuration commands to build a list of CLNS address templates with associated permit and deny conditions for use in CLNS filter expressions. CLNS filter expressions are used in the creation and use of CLNS access lists. The no form of this command deletes the entire filter set.

sname	Alphanumeric name to apply to this filter set.
permit \| deny	(Optional) Addresses matching the pattern specified by template are to be permitted or denied. If neither permit nor deny is specified, permit is assumed.
template	Address template, template alias name, or the keyword default. Address templates and alias names are described under the description of the clns template-alias global configuration command. The default keyword denotes a zero-length prefix and matches any address.

Use the clns holding-time global configuration command to allow the sender of an ESH or ISH to specify the length of time you consider the information in the hello packets to be valid. You can restore the default value (300 seconds or 5 minutes) by using the no form of this command.

Use the clns host global configuration command to define a name-to-NSAP mapping that can then be used with commands requiring NSAPs.

name	Desired name for the NSAP. The first character can be either a letter or a number, but if you use a number, the operations you can perform are limited.
nsap	NSAP that the name maps to.

Use the clns is-neighbor interface configuration command to list all intermediate systems that will be used when you manually specify the NSAP-to-SNPA mapping. The SNPAs are the MAC addresses. Use the no form of this command to delete the specified IS neighbor.

Use the clns mtu interface configuration command to set the MTU packet size for the interface. The no form of this command restores the default and maximum packet size.

Use the clns net global configuration command to assign a static address for a router. If a router is configured to support ISO CLNS but is not configured to dynamically route CLNS packets using ISO-IGRP or IS-IS, use this command to assign an address to the router. The no form of this command removes any previously configured NET or NSAP address.

net-address	Network Entity Title (NET). See this command in the Router Products Command Reference publication for the algorithm used.
name	CLNS host name to be associated with this interface.

Use this form of the clns net command as an interface configuration command to assign an NSAP address or name to a router interface. If a router is configured to support ISO CLNS, but is not configured to dynamically route CLNS packets using a ISO-IGRP or IS-IS, use this command to assign an address to the router. The no form of this command removes any previously configured NSAP address.

Use the clns packet-lifetime global configuration command to specify the initial lifetime for locally generated packets. The no form of this command removes the parameter's settings.

Use the clns rdpdu-interval interface configuration command to determine the minimum interval time, in milliseconds, between redirect PDUs (RDPDUs). A milliseconds value of zero or the no form of this command turns off the interval rate and effectively sets no limit between RDPDUs.

clns route nsap-prefix type number [snpa-address]
no clns route nsap-prefix

Use this form of the clns route global configuration command to create an interface static route. The no form of the command removes this route.

nsap-prefix	Network service access point prefix. This value is entered into a static routing table and used to match the beginning of a destination NSAP. The longest NSAP-prefix entry that matches is used.
type	Interface type.
number	Interface unit number.
snpa-address	(Optional) Optional for serial links; required for multiaccess networks.

Use this form of the clns route global configuration command to enter a specific static route. NSAPs that start with nsap-prefix are forwarded to next-hop-net or the name of the next hop. The no form of this command removes this route.

nsap-prefix	Network service access point prefix. This value is entered into a static routing table and used to match the beginning of a destination NSAP. The longest NSAP-prefix entry that matches is used.
next-hop-net	Next-hop Network Entity Title. This value is used to establish the next hop of the route for forwarding packets.
name	Name of the next hop node. This value can be used instead of the next-hop NET to establish the next hop of the route for forwarding packets.

Use this form of the clns route default global configuration command to configure a default zero-length prefix rather than type an NSAP prefix. The no form of this command removes this route.

nsap-prefix	Network service access point prefix that is a default zero-length prefix.
type	Interface type. Specify the interface immediately followed by the unit number; there is no space between the two. For example, ethernet3.
number	Interface unit number.

Use this form of the clns route discard global configuration command to tell a router explicitly to discard packets with NSAP addresses that match the specified nsap-prefix. The no form of this command removes this route.

nsap-prefix	Network service access point prefix. This value is entered into a static routing table and used to match the beginning of a destination NSAP. The longest NSAP-prefix entry that matches is used.
discard	Explicitly tells a router to discard packets with NSAPs that match the specified nsap-prefix.

Use the clns route-cache interface configuration command to allow fast switching through the cache. To disable fast switching, use the no form of this command.

Use the clns router isis interface configuration command to enable IS-IS routing for OSI on a specified interface. Use the no form of this command with the appropriate area tag to disable IS-IS on the interface.

Use the clns router iso-igrp interface configuration command to specify ISO-IGRP routing on a specified interface. Use the no form of this command with the appropriate tag to disable ISO-IGRP routing on the interface.

tag	Meaningful name for routing process. It must be unique among all CLNS router processes for a given router. This tag should be the same as defined for the routing process in the router iso-igrp global configuration command.
level 2	(Optional) Allows the interface to advertise Level 2 information.

Use the clns routing global configuration command to enable routing of CLNS packets. Use the no form of this command to disable CLNS routing.

Use the clns security pass-through global configuration command to allow the router to pass packets that have security options set. To revert to the default, use the no form of this command.

Use the clns send-erpdu interface configuration command to allow CLNS to send an error PDU when the routing software detects an error in a data PDU. To disable this function, use the no form of this command.

Use the clns send-rdpdu interface configuration command to allow CLNS to send redirect PDUs (RDPDUs) when a better route for a given host is known. To disable this function, use the no form of this command.

Use the clns split-horizon interface configuration command to implement split horizon for ISO-IGRP updates. The no form of this command disables this feature.

Use one or more clns template-alias global configuration commands to build a list of alphanumeric aliases of CLNS address templates for use in the definition of CLNS filter sets. The no form of this command deletes the alias.

name	Alphanumeric name to apply as an alias for the template.
template	Address template. See this command in the Router Products Command Reference publication for more information.

Use the clns want-erpdu global configuration command to specify whether to request error PDUs on packets sourced by the router. The no form of this command removes the parameter's settings.

Use the distance router configuration command to configure the administrative distance for CLNS routes learned. The no form of this command restores the administrative distance to the default.

value	Administrative distance, indicating the trustworthiness of a routing information source. This argument has a numerical value between 0 and 255. A higher relative value indicates a lower trustworthiness rating. Preference is given to routes with smaller values. Defaults are: static routes—10; ISO-IGRP routes—100; IS-IS routes—110. The default, if unspecified, is 110.
clns	(Optional) CLNS-derived routes for IS-IS.

Use the domain-password router configuration command to configure the routing domain authentication password. The no form of this command disables the password.

Use the ip domain-lookup nsap global configuration command to allow Domain Name System (DNS) queries for CLNS addresses. To disable this feature, specify the no form of this command.

Use the is-type router configuration command to configure the IS-IS level at which the router is to operate. The no form of this command resets the parameter to the default.

level-1	Causes the router to act as a station router.
level-1-2	Causes the router to act as both a station router and an area router. This is the default.
level-2-only	Causes the router to act as an area router only.

Use the isis adjacency-filter interface configuration command to filter the establishment of IS-IS adjacencies. Use the no form of this command to disable filtering of the establishment of IS-IS adjacencies.

name	Name of the filter set or expression to apply.
match-all	(Optional) All NSAP addresses must match the filter in order to accept the adjacency. If not specified (the default), only one address need match the filter in order for the adjacency to be accepted.

Use the isis circuit-type interface configuration command to configure the type of adjacency desired for the specified interface. The no form of this command resets the circuit type to Level l and Level 2.

level-1	Level 1 adjacency can be established if there is at least one area address in common between this system and its neighbors.
level-1-2	Level 1 and 2 adjacency is established if the neighbor is also configured as level-1-2 and there is at least one area in common. If there is no area in common, a Level 2 adjacency is established. This is the default.
level-2-only	Level 2 adjacency is established on the circuit. If the neighboring router is a Level 1 only router, no adjacency will be established.

Use the isis csnp-interval interface configuration command to configure the IS-IS complete sequence number PDUs (CSNP) interval for the specified interface. The no form of this command restores the default value.

seconds	Interval of time in seconds between transmission of CSNPs on multiaccess networks. (Only applies for the designated router.) The default is 10 seconds.
level-1	Interval of time between transmission of CSNPs for Level 1 independently.
level-2	Interval of time between transmission of CSNPs for Level 2 independently.

Use the isis hello-interval interface configuration command to specify the length of time in seconds between hello packets that the router sends on the specified interface. The no form of this command restores the default value.

seconds	Unsigned integer value. A value three times the hello interval seconds is advertised as the holdtime in the hello packets transmitted. It must be the same for all routers attached to a common network. With smaller hello intervals, topological changes are detected faster, but there is more routing traffic. The default is 10 seconds.
level-1	Configure the hello interval for Level 1 independently. Use this on X.25, SMDS, and Frame Relay multiaccess networks.
level-2	Configure the hello interval for Level 2 independently. Use with X.25, SMDS, and Frame Relay multiaccess networks.

isis metric default-metric delay-metric expense-metric error-metric
{level-1 | level-2}
no isis metric {level-1 | level-2}

Use the isis metric interface configuration command to configure the metric (or cost) for the specified interface. The no form of this command restores the default metric value.

default-metric	Metric used for the redistributed route. The range is from 0 through 63. The default value is 10.
delay-metric	Not supported.
expense-metric	Not supported.
error-metric	Not supported.
level-1	The router acts as a station router (Level 1) only.
level-2	The router acts as an area router (Level 2) only.

Use the isis password interface configuration command to configure the authentication password for a specified interface. The no form of this command disables authentication for IS-IS.

password	Authentication password you assign for an interface.
level-1	Configure the authentication password for Level 1 independently. For Level 1 routing, the router acts as a station router only.
level-2	Configure the authentication password for Level 2 independently. For Level 2 routing, the router acts as an area router only.

Use the isis priority interface configuration command to configure the priority of this system for designated router election. The no form of this command resets priority to 64.

value	Priority of a router; a number from 0 through 127. The default is 64.
level-1	Set priority of a router for Level 1 independently.
level-2	Set priority of a router for Level 2 independently.

Use the isis retransmit-interval interface configuration command to configure the number of seconds between retransmission of IS-IS link-state PDU (LSP) retransmission for point-to-point links. The no form of this command restores the default value.

seconds

Integer that should be greater than the expected round-trip delay between any two routers on the attached network. The setting of this parameter should be conservative, or needless retransmission will result. The value should be larger for serial lines and virtual links. The default is 5 seconds.

Use the iso-igrp adjacency-filter interface configuration command to filter the establishment of ISO-IGRP adjacencies. Use the no form of this command to disable filtering of the establishment of ISO-IGRP adjacencies.

To define the address match criterion, use the match clns address route-map configuration command; routes that have a network address matching one or more of the names—and that satisfy all other defined match criteria—will be redistributed. To remove the match criterion, use the no form of this command.

Use the match clns next-hop route-map configuration command to define the next-hop match criterion; routes that have a next-hop router address matching one of the names—and that satisfy all other defined match criteria—will be redistributed.

Use the match clns route-source route-map configuration command to define the route-source match criterion; routes that have been advertised by routers at the address specified by the name—and that satisfy all other defined match criteria—will be redistributed. Use the no form of this command to remove the specified match criterion.

Use the match interface route-map configuration command to define the interface match criterion; routes that have the next hop out one of the interfaces specified—and that satisfy all other defined match criteria—will be redistributed. Use the no form of this command to remove the specified match criterion.

Use the match metric route-map configuration command to define the metric match criterion; routes that have the specified metric—and that satisfy all other defined match criteria—will be redistributed. Use the no form of this command to remove the specified match criterion.

Use the match route-type route-map configuration command to define the route-type match criterion; routes that have the specified route type—and that satisfy all other defined match criteria—will be redistributed. Use the no form of the command to remove the specified match criterion.

Use the metric weights router configuration command to specify different metrics for the ISO-IGRP routing protocol on CLNS. This command allows you to configure the metric constants used in the ISO-IGRP composite metric calculation of reliability and load. Use the no metric weights command to return the five k constants to their default values.

qos	Quality of service. QOS defines transmission quality and availability of service. The value must be 0, the default metric value.
k1, k2, k3, k4, k5	Values that apply to ISO-IGRP for the default metric QOS. The k values are metric constants used in the ISO-IGRP equation that converts an IGRP metric vector into a scalar quantity. They are numbers from 0 through 127; higher numbers mean a greater multiplier effect. The defaults are k1 = 1; k2 = 0; k3 = 1; k4 = 0; k5 = 0.

Use the net router configuration command to configure a Network Entity Title (NET) for the specified routing process. The no form of this command removes a specific NET; you must specify the NET.

Use the ping user and privileged EXEC command to send ISO CLNS echo packets to test the reachability of a remote host over a connectionless OSI network.

clns	CLNS protocol.
host	Host name of system to ping.
address	Address of system to ping.

[no] redistribute protocol [tag] [route-map map-tag]
redistribute {static [clns | ip]}

Use the redistribute router configuration command to redistribute routing information from one domain into another routing domain. The no form of this command disables redistribution, or disables any of the specified keywords.

protocol	Type of other routing protocol that is to be redistributed as a source of routes into the current routing protocol being configured. The keywords supported are iso-igrp, isis, and static [clns]. The keyword static [clns] is used to redistribute CLNS prefix static routes. This causes the router to inject any static CLNS routes into the domain. The optional clns keyword is used when redistributing into IS-IS.
tag	(Optional) Meaningful name for a routing process.
route-map map-tag	(Optional) A route map should be interrogated to filter the importation of routes from this source routing protocol to the current routing protocol. If not specified, all routes are redistributed. If this keyword is specified, but no route map tags are listed, no routes will be imported. The argument map-tag is the identifier of a configured route map.
static	The keyword static is used to redistribute static routes. When used without the optional keywords, this causes the router to inject any OSI static routes into an OSI domain.
clns	(Optional) The clns keyword is used when redistributing OSI static routes into an IS-IS domain.
ip	(Optional) The ip keyword is used when redistributing IP into an IS-IS domain.

Use the route-map global configuration command, and the route-map configuration commands match and set, to define the conditions for redistributing routes from one routing protocol into another. Each route-map command has a list of match and set commands associated with it. The match commands specify the match criteria—the conditions under which redistribution is allowed for the current route-map. The set commands specify the set actions—the particular redistribution actions to perform if the criteria enforced by the match commands are met. The no form of this command deletes the route map.

map-tag	Meaningful name for the route map. The redistribute command uses this name to reference this route map. Multiple route-maps can share the same map tag name. Can either be an expression or a filter set.
permit	If the match criteria are met for this route map, and permit is specified, the route is redistributed as controlled by the set actions. If the match criteria are not met, and permit is specified, the next route map with the same map-tag is tested. If a route passes none of the match criteria for the set of route maps sharing the same name, it is not redistributed by that set.
deny	If the match criteria are met for the route map, and deny is specified, the route is not redistributed, and no further route maps sharing the same map tag name will be examined.
sequence-number	Number that indicates the position a new route map is to have in the list of route maps already configured with the same name. If given with the no form of the command, it specifies the position of the route map that should be deleted.

Use the router isis global configuration command to enable the IS-IS routing protocol on your router and to configure the IS-IS routing process. This command identifies the area the router will work in and lets the router know that it will be routing dynamically rather than statically. The no form of this command with the appropriate tag disables IS-IS routing for the system.

Use the router iso-igrp global configuration command to identify the area the router will work in and let it know that it will be routing dynamically using the ISO-IGRP protocol. The no form of this command with the appropriate tag disables ISO-IGRP routing for the system.

tag

(Optional) Meaningful name for a routing process. For example, you could define a routing process named Finance for the Finance department, and another routing process named Marketing for the Marketing department. If not specified, a null tag is assumed. The tag argument must be unique among all CLNS router processes for a given router.

Use the set level route-map configuration command to specify the routing level of routes to be advertised into a specified area of the routing domain. Use the no form of this command to disable advertising the specified routing level into a specified area.

level	Redistributed routes are advertised into this specified area of the routing domain. For IS-IS destinations, the default value is level-2.
level-1	Inserted in IS-IS Level 1 LSPs.
level-2	Inserted in IS-IS Level 2 LSPs.
level-1-2	Inserted into both Level 1 and Level 2 IS-IS LSPs.

Use the set metric route-map configuration command to set the metric value to give the redistributed routes.

Use the set metric-type route-map configuration command to set the metric type to give redistributed routes.

metric-type	Metric type to give redistributed routes. There is no default value.
internal	IS-IS internal metric.
external	IS-IS external metric.

Use set tag route-map configuration command to set a tag value to associate with the redistributed routes.

tag	Tag value to associate with the redistributed route. If not specified, the default action is to forward the tag in the source routing protocol onto the new destination protocol.
tag-value	Name for the tag.

Use the show clns EXEC command to display information about the CLNS network.

Use the show clns cache EXEC command to display the CLNS routing cache. The cache contains an entry for each destination that has packet switching enabled. The output of this command includes entries showing each destination for which the router has switched a packet in the recent past. This includes the router.

Use the show clns es-neighbors EXEC command to list the ES neighbors (end-system adjacencies) that this router knows about.

type	(Optional) Interface type.
number	(Optional) Interface unit number.
detail	(Optional) When specified, the areas associated with the End Systems are displayed. Otherwise, a summary display is provided.

Use the show clns filter-expr EXEC command to display one or all currently defined CLNS filter expressions.

name	(Optional) Name of the filter expression to display. If none is specified, all are displayed.
detail	(Optional) When specified, expressions are evaluated down to their most primitive filter set terms before being displayed.

Use the show clns filter-set EXEC command to display one or all currently defined CLNS filter sets.

Use the show clns interface EXEC command to list the CLNS-specific information about each interface.

Use the show clns is-neighbors EXEC command to display IS-IS related information for IS-IS router adjacencies. Neighbor entries are sorted according to the area in which they are located.

type	(Optional) Interface type.
number	(Optional) Interface unit number.
detail	(Optional) When specified, the areas associated with the Intermediate Systems are displayed. Otherwise, a summary display is provided.

type	(Optional) Interface type.
number	(Optional) Interface unit number.
detail	(Optional) When specified, the area addresses advertised by the neighbor in the hello messages is displayed. Otherwise, a summary display is provided.

Use the show clns protocol EXEC command to list the protocol-specific information for each ISO-IGRP routing process in the router. There will always be at least two routing processes, a Level 1 and a Level 2, and there can be more.

Use the show clns route EXEC command to display all of the destinations to which this router knows how to route packets.

The show clns route command shows the IS-IS Level 2 routing table as well as static and ISO-IGRP learned prefix routes. This table stores IS-IS area addresses and prefix routes. Destinations are sorted by category.

Use the show clns traffic EXEC command to list the CLNS packets this router has seen.

Use the show isis database EXEC command to display the IS-IS link state database. A summary display is provided if no options are specified.

level-1	(Optional) Displays the IS-IS link state database for Level 1.
level-2	(Optional) Displays the IS-IS link state database for Level 2.
l1	(Optional) Abbreviation for the option level-1.
l2	(Optional) Abbreviation for the option level-2.
detail	(Optional) When specified, the contents of each LSP is displayed. Otherwise, a summary display is provided.
lspid	(Optional) Link-state protocol ID (LSPID). Displays the contents of the specified link state packet. The LSPID must be of the form xxxx.xxxx.xxxx.yy-zz or name.yy-zz. For a description of these values, see the table in the "Usage Guidelines" for this command in the Router Products Command Reference publication.

Use the show isis routes EXEC command to display the IS-IS Level 1 forwarding table for IS-IS learned routes.

Use the show route-map EXEC command to display all route-maps configured or only the one specified.

Use the timers basic router configuration command to configure ISO-IGRP timers. The no form of this command restores the default values.

update-interval	Time, in seconds, between the sending of routing updates. The default value is 90 seconds.
holddown-interval	Time, in seconds, a system or area router is kept in holddown state, during which routing information regarding better paths is suppressed. (A router enters into a holddown state when an update packet is received that indicates the route is unreachable. The route is marked inaccessible and advertised as unreachable. However, the route is still used for forwarding packets.) When the holddown interval expires, routes advertised by other sources are accepted and the route is no longer inaccessible. The default value is 145 seconds.
invalid-interval	Time, in seconds, that a route remains in the routing table after it has been determined that it is not reachable. After that length of time, the route is removed from the routing table. The default value is 135 seconds.

You can use the trace privileged EXEC command to trace routes on a router configured with the ISO CLNS protocol.

Use the trace clns user EXEC command to discover the CLNS routes the router's packets will actually take when traveling to their destination.

Use the which-route EXEC command if you want to know which next-hop router will be used or if you have multiple processes running and want to troubleshoot your configuration. This command displays the routing table in which the specified CLNS destination is found.

nsap	Specific NSAP to map to the MAC address.
snpa	Data link (MAC) address .

nsap	NSAP address of a specific intermediate system to enter as a neighbor to a specific MAC address.
snpa	Data link (MAC) address.

nsap-address	Specific NSAP address.
name	Name to be associated with this interface.

metric	Metric value to give the redistributed routes. There is no default value.
metric-value	Route metric. This can be an IGRP five-part metric.

domain	(Optional) A particular ISO-IGRP routing domain.
area-tag	(Optional) A particular IS-IS area.

level-1	IS-IS Level 1 routes.
level-2	IS-IS Level 2 routes.

nsap-address	CLNS destination network address.
clns-name	Destination host name.

Table of Contents

ISO CLNS Commands