The Internetwork Operating System (IOS) user interface provides access to several different command modes. Each command mode provides a group of related commands. This chapter describes how to access and list the commands available in each command mode, and explains the primary uses for each command mode.

For security purposes, the IOS provides two levels of access to commands: user and privileged. The unprivileged, user mode is called user EXEC mode. The privileged mode is called privileged EXEC mode, and requires a password. The commands available in user EXEC mode are a subset of the commands available in privileged EXEC mode.

From the privileged level, you can access global configuration mode and ten specific configuration modes: interface, subinterface, controller, hub, map-list, map-class, line, router, ipx-router, and route-map configuration. In addition, if your router does not find a valid system image, or if its configuration file is corrupted at startup, the system might enter read-only memory (ROM) monitor mode. Entering a question mark (?) at the system prompt allows you to obtain a list of commands available for each command mode.

Almost every system configuration command also has a no form. In general, use the no form to disable a feature or function. Use the command without the keyword no to reenable a disabled feature or to enable a feature that is disabled by default. For example, IP routing is enabled by default. Specify the command no ip routing to disable IP routing and specify ip routing to reenable it. The Router Products Command Reference publication provides the complete syntax for every router configuration command and describes what the no form of a command does.

The user interface also provides context-sensitive help on command syntax. This chapter describes how to use the help system. It also describes the command editing and command history features that enable you to recall previous command entries and easily edit command entries.

For a complete description of the commands mentioned in this chapter, refer to the "User Interface Commands" chapter in the Router Products Command Reference publication.

User Interface Task List

You can perform the tasks in the following sections to become familiar with the IOS user interface:

Access Each Command Mode

This section describes how to access each of the IOS command modes:

Table 2-1 lists the command modes, how to access each mode, the prompt you will see while you are in that mode, the main uses for each configuration mode, and the method to exit that mode. The prompts listed assume the default router name "Router." Table 2-1 might not include all of the possible ways to access or exit each command mode.

Command Mode	Access Method	Prompt	Exit Method
User EXEC	Log in to router.	`Router>`	Use the logout command.
Privileged EXEC	From user EXEC mode, use the enable EXEC command.	`Router#`	To exit back to user EXEC mode, use the disable command. To exit into global configuration mode, use the configure privileged EXEC command.
Global configuration	From privileged EXEC mode, use the configure privileged EXEC command.	`Router(config)#`	To exit to privileged EXEC mode, use the exit or end command or press Ctrl-Z. To exit to interface configuration mode, enter an interface configuration command.
Interface configuration	From global configuration mode, enter by specifying an interface with an interface command.	`Router(config-if)#`	To exit to global configuration mode, use the exit command. To exit to privileged EXEC mode, press Ctrl-Z. To exit to subinterface configuration mode, specify a subinterface with the interface command.
Subinterface configuration	From interface configuration mode, specify a subinterface with an interface command.	`Router(config-subif)#`	To exit to global configuration mode, use the exit command. To exit to privileged EXEC mode, press Ctrl-Z.
Controller configuration	From global configuration mode, use the controller command to configure a channelized T1 interface.	`Router(config-controller)#`	To exit to global configuration mode, use the exit command.
Hub configuration	From global configuration mode, enter by specifying a hub with the hub command.	`Router(config-hub)#`	To exit to global configuration mode, use the exit command. To exit to privileged EXEC mode, press Ctrl-Z.
Map-list configuration	From global configuration mode, define a map list with the map-list command.	`Router(config-map-list)#`	To exit to map-class configuration mode, use the map-class command. To exit to privileged EXEC mode, press Ctrl-Z.
Map-class configuration	From global configuration mode, configure a map class with the map-class command.	`Router(config-map-class)#`	To exit to global configuration mode, use the exit command. To exit to privileged EXEC mode, press Ctrl-Z.
Line configuration	From global configuration mode, enter by specifying a line with a line command.	`Router(config-line)#`	To exit to global configuration mode, use the exit command. To exit to privileged EXEC mode, press Ctrl-Z.
Router configuration	From global configuration mode, enter by entering a command that begins with router (such as router igrp).	`Router(config-router)#`	To exit to global configuration mode, use exit command. To exit to privileged EXEC mode, press Ctrl-Z.
IPX-router configuration	From global configuration mode, enter by issuing the ipx routing command, then a command that begins with ipx router (such as ipx router eigrp).	`Router(config-ipx-router)#`	To exit to global configuration mode, use the exit command.
Route-map configuration	From global configuration mode, enter by specifying the route-map command.	`Router(config-route-map)#`	To exit to global configuration mode, use the exit command. To exit to privileged EXEC mode, press Ctrl-Z.
ROM monitor	From privileged EXEC mode, use the reload EXEC command. Press Break during the first 60 seconds while the system is booting.	`>`	To exit to user EXEC mode, press c to continue.

Table 2-1: Summary of Command Modes

Command Mode Access Method Prompt Exit Method

User EXEC

Log in to router.

Router>

Use the logout command.

Privileged EXEC

From user EXEC mode, use the enable EXEC command.

Router#

To exit back to user EXEC mode, use the disable command.

To exit into global configuration mode, use the configure privileged EXEC command.

Global configuration

From privileged EXEC mode, use the configure privileged EXEC command.

Router(config)#

To exit to privileged EXEC mode, use the exit or end command or press Ctrl-Z.

To exit to interface configuration mode, enter an interface configuration command.

Interface configuration

From global configuration mode, enter by specifying an interface with an interface command.

Router(config-if)#

To exit to global configuration mode, use the exit command.

To exit to privileged EXEC mode, press Ctrl-Z.

To exit to subinterface configuration mode, specify a subinterface with the interface command.

Subinterface configuration

From interface configuration mode, specify a subinterface with an interface command.

Router(config-subif)#

To exit to global configuration mode, use the exit command.

To exit to privileged EXEC mode, press Ctrl-Z.

Controller configuration

From global configuration mode, use the controller command to configure a channelized T1 interface.

Router(config-controller)#

To exit to global configuration mode, use the exit command.

Hub configuration

From global configuration mode, enter by specifying a hub with the hub command.

Router(config-hub)#

To exit to global configuration mode, use the exit command.

To exit to privileged EXEC mode, press Ctrl-Z.

Map-list configuration

From global configuration mode, define a map list with the map-list command.

Router(config-map-list)#

To exit to map-class configuration mode, use the map-class command.

To exit to privileged EXEC mode, press Ctrl-Z.

Map-class configuration

From global configuration mode, configure a map class with the map-class command.

Router(config-map-class)#

To exit to global configuration mode, use the exit command.

To exit to privileged EXEC mode, press Ctrl-Z.

Line configuration

From global configuration mode, enter by specifying a line with a line command.

Router(config-line)#

To exit to global configuration mode, use the exit command.

To exit to privileged EXEC mode, press Ctrl-Z.

Router configuration

From global configuration mode, enter by entering a command that begins with router (such as router igrp).

Router(config-router)#

To exit to global configuration mode, use exit command.

To exit to privileged EXEC mode, press Ctrl-Z.

IPX-router configuration

From global configuration mode, enter by issuing the ipx routing command, then a command that begins with ipx router (such as ipx router eigrp).

Router(config-ipx-router)#

To exit to global configuration mode, use the exit command.

Route-map configuration

From global configuration mode, enter by specifying the route-map command.

Router(config-route-map)#

To exit to global configuration mode, use the exit command.

To exit to privileged EXEC mode, press Ctrl-Z.

ROM monitor

From privileged EXEC mode, use the reload EXEC command. Press Break during the first 60 seconds while the system is booting.

>

To exit to user EXEC mode, press c to continue.

User EXEC Mode

After you log in to the router, you are automatically in user EXEC command mode. The EXEC commands available at the user level are a subset of those available at the privileged level. In general, the user EXEC commands allow you to connect to remote routers, change terminal settings on a temporary basis, perform basic tests, and list system information.

To list the user EXEC commands, complete the following task:

Task	Command
List the user EXEC commands.	?

The user-level prompt consists of the router's host name followed by the angle bracket (>):

Router>

The default host name is Router unless it has been changed during initial configuration using the setup command. (Refer to the Router Products Getting Started Guide for information on the setup facility.) You can also change the router name using the hostname global configuration command described in the "System Management Commands" chapter in the Router Products Command Reference publication.

To list the commands available in user EXEC mode, enter a question mark (?) as shown in the following example:

Router> ? 

Exec commands:
 connect          Open a terminal connection
 disconnect       Disconnect an existing telnet session
 enable           Turn on privileged commands
 exit             Exit from the EXEC
 help             Description of the interactive help system
 lock             Lock the terminal
 login            Log in as a particular user
 logout           Exit from the EXEC
 name-connection  Name an existing telnet connection
 ping             Send echo messages
 resume           Resume an active telnet connection
 show             Show running system information
 systat           Display information about terminal lines
 telnet           Open a telnet connection
 terminal         Set terminal line parameters
 where            List active telnet connections
Router>

The list of commands might vary slightly from this example, depending upon how your router has been configured.

Privileged EXEC Mode

Because many of the privileged commands set operating parameters, privileged access should be password-protected to prevent unauthorized use. The privileged command set includes those commands contained in user EXEC mode, as well as the configure command through which you can access the remaining command modes. Privileged EXEC mode also includes high-level testing commands, such as debug. For details on the debug command, see the Debug Command Reference publication.

To access and list the privileged EXEC commands, complete the following tasks:

Task	Command
Step 1. Enter the privileged EXEC mode.	enable [password]
Step 2. List privileged EXEC commands.	?

If the system administrator has set a password, you are prompted to enter it before being allowed access to privileged EXEC mode. The password is not displayed on the screen and is case sensitive. The system administrator uses the enable password global configuration command to set the password that restricts access to privileged mode. This command is described in the "System Management Commands" chapter in the Router Products Command Reference publication.

The privileged-level prompt consists of the router's host name followed by the pound sign (#). (If the router was named with the hostname command, that name would appear as the prompt instead of "Router.")

Router#

The following example shows how to access privileged EXEC mode and list privileged EXEC commands:

Router> enable

Password:
Router# ? 

Exec commands:
 bfe              For manual emergency modes setting
 clear            Reset functions
 clock            Manage the system clock
 configure        Enter configuration mode
 connect          Open a terminal connection
 copy             Copy a config file to or from a tftp server
 debug            Debugging functions
 disable          Turn off privileged commands
 disconnect       Disconnect an existing telnet session
 enable           Turn on privileged commands
 exit             Exit from the EXEC
 help             Description of the interactive help system
 llc2             Execute llc2 tests
 lock             Lock the terminal
 login            Log in as a particular user
 logout           Exit from the EXEC
 name-connection  Name an existing telnet connection
 ping             Send echo messages
 reload           Halt and perform a cold restart
 resume           Resume an active telnet connection
 send             Send a message to other tty lines
 setup            Run the SETUP command facility
 show             Show running system information
 systat           Display information about terminal lines
 telnet           Open a telnet connection
 terminal         Set terminal line parameters
 test             Test subsystems, memory, and interfaces
 trace            Trace route to destination
 where            List active telnet connections
 which-route      Do route table lookup and display results
 write            Write running configuration to memory, network, or terminal

The list of commands might vary slightly from this example, depending upon how your router has been configured.

From the privileged level, you can access global configuration mode. For instructions, see the "Global Configuration Mode" section, which follows this section.

To return from privileged EXEC mode to user EXEC mode, perform the following task:

Task	Command
Move from privileged EXEC mode to user EXEC mode.	disable

Global Configuration Mode

Global configuration commands apply to features that affect the system as a whole. Use the configure privileged EXEC command to enter global configuration mode. When you enter this command, the EXEC prompts you for the source of the configuration commands:

Configuring from terminal, memory, or network [terminal]?

You can then specify either the terminal, nonvolatile memory (NVRAM), or a file stored on a network server as the source of configuration commands (see the "System Image, Microcode Image, and Configuration File Load Commands" chapter in the Router Products Command Reference publication). The default is to enter commands from the terminal console. Pressing the Return key begins this configuration method.

Commands to enable a particular routing or bridging function are also global configuration commands. For information on protocol-specific global configuration commands, see the appropriate chapter in this guide.

To access and list the global configuration commands, complete the following tasks:

Task	Command
Step 1. At the terminal, from the privileged EXEC mode, enter global configuration mode.	configure¹ <CR>
Step 2. List the global configuration commands.	?

¹This command is documented in the "System Image, Microcode Image, and Configuration File Load Commands" chapter in the Router Products Command Reference publication.

The following example shows how to access global configuration mode and list global configuration commands:

Router# configure

Configuring from terminal, memory, or network [terminal]? <CR>

Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# ? 

Configure commands:
 access-list            Add an access list entry
 apollo                 Apollo global configuration commands
 appletalk              Appletalk global configuration commands
 arp                    Set a static ARP entry
 async-bootp            Modify system bootp parameters
 autonomous-system      Specify local AS number to which we belong
 banner                 Define a login banner
 boot                   Modify system boot parameters
 bridge                 Transparent bridging
 buffers                Adjust system buffer pool parameters
 busy-message           Display message when connection to host fails
 chat-script            Define a modem chat script
 clns                   Global CLNS configuration subcommands
 clock	                  Configure time-of-day clock
 decnet                 Global DECnet configuration subcommands
 default-value          Default character-bits values
 dialer-list            Create a dialer list entry
 enable                 Modify enable password parameters
 end                    Exit from configure mode
 exit                   Exit from configure mode
 frame-relay            Global frame relay configuration commands
 help                   Description of the interactive help system
 hostname               Set system's network name
 interface              Select an interface to configure
 ip                     Global IP configuration subcommands
 ipx                    Novell/IPX global configuration commands
 line                   Configure a terminal line
 lnm                    IBM Lan Manager
 locaddr-priority-list  Establish queueing priorities based on LU address
 logging                Modify message logging facilities
 login-string           Define a host-specific login string
 mop                    The DEC MOP Server
 netbios                NETBIOS access control filtering
 no                     Negate a command or set its defaults
 ntp                    Configure NTP
 priority-list          Build a priority list
 queue-list             Build a custom queue list
 rif                    Source-route RIF cache
 route-map              Create route-map or enter route-map command mode
 router                 Enable a routing process
 scheduler-interval     Maximum interval before running lowest priority process
 service                Modify use of network based services
 smt-queue-threshold    Set the max number of unprocessed SMT frames
 snmp-server            Modify SNMP parameters
 source-bridge          Source-route bridging ring groups
 stun                   STUN global configuration commands
 tacacs-server          Modify TACACS query parameters
 tftp-server            Provide TFTP service for netload requests
 tn3270                 tn3270 configuration command
 username               Establish User Name Authentication
 vines                  Vines global configuration commands
 x25                    X.25 Level 3
 xns                    XNS global configuration commands

The list of commands might vary slightly from this example, depending upon how your router has been configured.

To exit global configuration command mode and return to privileged EXEC mode, use one of the following commands:

Task	Command
Exit global configuration mode.	exit end Ctrl-Z

From global configuration mode, you can access ten configuration modes: interface, subinterface, hub, controller, map-list, map-class, line, router, ipx-router, and route-map configuration commands. These command modes are described in the following sections.

Interface Configuration Mode

Many features are enabled on a per-interface basis. Interface configuration commands modify the operation of an interface such as an Ethernet, FDDI, or serial port. Interface configuration commands always follow an interface global configuration command, which defines the interface type.

For details on interface configuration commands that affect general interface parameters, such as bandwidth, clock rate, and so on, see the "Configuring Interfaces" chapter. For protocol-specific commands, see the appropriate chapter in this guide.

To access and list the interface configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, enter interface configuration mode.	interface interface-type interface-number¹
Step 2. List the interface configuration commands.	?

¹This command is documented in the "Interface Commands" chapter in the Router Products Command Reference publication.

In the following example, serial interface 0 is about to be configured. The new prompt
Router(config-if)# indicates interface configuration mode. In this example, the user asks for help by requesting a list of commands.

Router(config)# interface serial 0 <CR>

Router(config-if)# ? 

Interface configuration commands:
 access-expression     Build a bridge boolean access expression
 apollo                Apollo interface subcommands
 appletalk             Appletalk interface subcommands
 arp                   Set arp type (arpa, probe, snap) or timeout
 backup                Modify dial-backup parameters
 bandwidth             Set bandwidth informational parameter
 bridge-group          Transparent bridging interface parameters
 clns                  CLNS interface subcommands
 clockrate             Configure serial interface clock speed
 custom-queue-list     Assign a custom queue list to an interface
 decnet                Interface DECnet config commands
 delay                 Specify interface throughput delay
 description           Interface specific description
 dialer                Dial-on-demand routing (DDR) commands
 dialer-group          Assign interface to dialer-list
 down-when-looped      Force looped serial interface down
 encapsulation         Set encapsulation type for an interface
 ethernet-transit-oui  Token-ring to Ethernet OUI handling
 exit                  Exit from interface configuration mode
 frame-relay           Set frame relay parameters
 hdh                   Set HDH mode
 help                  Description of the interactive help system
 hold-queue            Set hold queue depth
 ip                    Interface Internet Protocol config commands
 ipx                   Novell interface subcommands
 isis                  IS-IS commands
 iso-igrp              ISO-IGRP interface subcommands
 keepalive             Enable keepalive
 lapb                  X.25 Level 2 parameters (Link Access Procedure, Balanced)
 llc2                  LLC2 Interface Subcommands
 lnm                   IBM Lan Manager
 locaddr-priority      Assign a priority group
 loopback              Configure internal loopback on an interface
 mac-address           Manually set interface MAC address
 mop                   DEC MOP server commands
 mtu                   Set the interface Maximum Transmission Unit (MTU)
 netbios               Use a defined NETBIOS access list or enable name-caching
 no                    Negate a command or set its defaults
 ntp                   Configure NTP
 ppp                   Point-to-point protocol
 priority-group        Assign a priority group to an interface
 pulse-time            Enables pulsing of DTR during resets
 pup                   PUP interface subcommands
 sdlc                  SDLC commands
 sdllc                 Configure SDLC to LLC2 translation
 shutdown              Shutdown the selected interface
 smds                  Modify SMDS parameters
 source-bridge         Configure interface for source-route bridging
 stun                  STUN interface subcommands
 transmit-interface    Assign a transmit interface to a receive-only interface
 transmitter-delay     Set dead-time after transmitting a datagram
 tunnel                protocol-over-protocol tunneling
 tx-queue-limit        Configure card level transmit queue limit
 vines                 Vines interface subcommands
 xns                   XNS interface subcommands

The list of commands might vary slightly from this example, depending upon how your router has been configured.

To exit interface configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to privileged EXEC mode, press Ctrl-Z.

Subinterface Configuration Mode

You can configure multiple virtual interfaces (called subinterfaces) on a single physical interface. This feature is supported on serial interfaces with Frame Relay encapsulation.

Subinterfaces appear to be distinct physical interfaces to the various protocols. For example, Frame Relay networks provide multiple point-to-point links called permanent virtual circuits (PVCs). PVCs can be grouped under separate subinterfaces that in turn are configured on a single physical interface. From a bridging spanning-tree viewpoint, each subinterface is a separate bridge port, and a frame arriving on one subinterface can be sent out on a another subinterface.

Subinterfaces also allow multiple encapsulations for a protocol on a single interface. For example, a router can receive an ARPA-framed IPX packet and forward the packet back out the same physical interface as a SNAP-framed IPX packet.

For detailed information on how to configure subinterfaces, see the "Configuring Interfaces" chapter, later in this publication.

To access and list the subinterface configuration commands, complete the following tasks:

Task	Command
Step 1. From interface configuration mode, configure a virtual interface.	See the example that follows. For a list of all interface commands that allow subinterface implementation, see the "Configuring Interfaces" chapter.
Step 2. List the subinterface configuration commands.	?

In the following example, a subinterface is configured for serial line 2, which is configured for Frame Relay encapsulation. The subinterface is called 2.1 to indicate that it is subinterface 1 of serial interface 2. The new prompt Router(config-subif)# indicates subinterface configuration mode. The subinterface can be configured to support one or more Frame Relay PVCs. To list the commands available in subinterface configuration mode, enter a question mark (?).

Router(config)# interface serial 2

Router(config-if)# encapsulation frame-relay

Router(config-if)# interface serial 2.1

Router(config-subif)# ?

Interface configuration commands:
 apollo        Apollo interface subcommands
 appletalk     Appletalk interface subcommands
 bandwidth     Set bandwidth informational parameter
 bridge-group  Transparent bridging interface parameters
 clns          CLNS interface subcommands
 decnet        Interface DECnet config commands
 delay         Specify interface throughput delay
 description   Interface specific description
 exit          Exit from interface configuration mode
 frame-relay   Set frame relay parameters
 ip            Interface Internet Protocol config commands
 ipx           Novell interface subcommands
 isis          IS-IS commands
 iso-igrp      ISO-IGRP interface subcommands
 no            Negate a command or set its defaults
 ntp           Configure NTP
 shutdown      Shutdown the selected interface

The list of commands might vary slightly from this example depending upon how your router has been configured.

To exit subinterface configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to privileged EXEC mode, press Ctrl-Z.

Control ler Configuration Mode

You can configure channelized T1 interfaces in the controller configuration mode.

To access and list the controller configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, configure a channelized T1 interface.	controller t1 slot/port ¹
Step 2. List the controller configuration commands.	?

¹This command is documented in the "Interface Commands" chapter in the Router Products Command Reference publication.

In the following example, a channelized T1 interface is being configured on interface 0/0. The new prompt Router(config-controller)# indicates controller configuration mode.

Router(config)# controller t1 0/0

Router(config-controller)# ?

Controller configuration commands:
  channel-group  Specify the timeslots to channel-group mapping for an
                 interface
  clocksource    Specify the clock source for a DS1 link
  exit           Exit from controller configuration mode
  framing        Specify the type of Framing on a DS1 link
  help           Description of the interactive help system
  linecode       Specify the line encoding method for a DS1 link
  loopback       Put the entire T1 line into loopback
  no             Negate a command or set its defaults
  shutdown       Shut down a DS1 link (send Blue Alarm)

Note The controller configuration mode applies only to the Cisco 7000 series MultiChannel Interface Processor (MIP) that has one or two CxBus Channelized T1 (CxCT1) port adaptor modules attached.

Hub Configuration Mode

Hub configuration commands configure hub functionality for an Ethernet interface on the
Cisco 2500. They always follow a hub global configuration command. To access and list the hub configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, use the hub command.	hub number port [port] ¹
Step 2. List the hub configuration commands.	?

¹This command is documented in the "Interface Configuration Commands" chapter in the Router Products Command Reference publication.

The following example shows how to enter hub configuration mode and list the hub configuration commands. In this example, the new prompt Router(config-hub)# indicates hub configuration mode.

Router (config)# hub ethernet 0 1 3

Router(config-hub)# ?

Hub configuration commands:
  auto-polarity   Enable automatic receiver polarity reversal
  exit            Exit from hub configuration mode
  help            Description of the interactive help system
  link-test       Enable Link Test Function of Hub port
  no              Negate or set default values of a command
  shutdown        Shutdown the selected port
  source-address  Enable Source Address control for Hub port

To exit hub configuration mode and return to global configuration mode, enter the exit command. To exit configuraton mode an return to privileged EXEC mode, pres Ctrl-Z.

Map-List Configu ration Mode

The Asynchronous Transfer Mode (ATM) interface in the Cisco 7000 series router supports a static mapping scheme that identifies the ATM address of remote hosts or routers.

Map-list configuration commands configure a map list. They always follow a map-list global configuration command. To access and list the map list configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, use the map-list command.	map-list name ¹
Step 2. List the map-list configuration commands.	?

¹This command is documented in the "ATM Configuration Commands" chapter in the Router Products Command Reference publication.

The following example shows how to enter map-list configuration mode and list the map list configuration commands. In this example, the static map-list configuration commands are listed. The new prompt Router(config-map-list)# indicates map-list configuration mode.

Router(config)# map-list atm

Router(config-map-list)# ?

Static maps list configuration commands:
  A.B.C.D              Protocol specific address
  aarp                 AppleTalk ARP
  apollo               Apollo Domain
  appletalk            AppleTalk
  arp                  IP ARP
  bridge               Bridging
  clns                 ISO CLNS
  clns_es              ISO CLNS End System
  clns_is              ISO CLNS Intermediate System
  cmns                 ISO CMNS
  compressedtcp        Compressed TCP
  decnet               DECnet
  decnet_node          DECnet Node
  decnet_prime_router  DECnet Prime Router
  decnet_router        DECnet Router
  exit-class           Exit from static map class configuration mode
  help                 Description of the interactive help system
  ip                   IP
  ipx                  Novell IPX
  no                   Negate or set default values of a command
  pad                  PAD links
  rsrb                 Remote Source-Route Bridging
  stun                 Serial Tunnel
  vines                Banyan VINES
  xns                  Xerox Network Services

The list of commands might vary slightly from this example, depending upon how your router has been configured.

To exit map-list configuration mode and return to global configuration mode, enter the exit command. To exit configuraton mode an return to privileged EXEC mode, pres Ctrl-Z.

Map-Class Config uration Mode

The ATM interface allows you to specify Quality of Service (QOS) parameters that control how much traffic the source router will be sending over a switched virtual circuit (SVC).

To define QOS parameters that are associated with a static map for an SVC, use the map-class global configuration command.

Task	Command
Step 1. From global configuration mode, configure a map class.	map-class encapsulation class-name¹
Step 2. List the map-class configuration commands.	?

¹This command is documented in the "ATM Configuration Commands" chapter in the Router Products Command Reference publication.

In the following example, the static map-class configuration commands are listed. The new prompt Router(config-map-class)# indicates map-class configuration mode.

Router(config)# map-class atm aaa

Router(config-map-class)# ?

Static maps class configuration commands:
atm         Configure atm static map class
exit-class  Exit from static map class configuration mode
help        Description of the interactive help system
no          Negate or set default values of a command

The list of commands might vary slightly from this example, depending upon how your router has been configured.

To exit map-class configuration mode and return to global configuration mode, enter the exit command. To exit configuraton mode an return to privileged EXEC mode, press Ctrl-Z.

Note The static mapping configuration mode applies only to the Cisco 7000 series router.

Line Configuration Mode

Line configuration commands modify the operation of a serial terminal line. Line configuration commands always follow a line command, which defines a line number. These commands are generally used to connect to remote routers, change terminal parameter settings on a line-by-line basis, and set up the auxiliary port modem configuration to support dial-on-demand routing (DDR) (see the "DDR Commands" chapter in the Router Products Command Reference publication).

To access and list the auxiliary port, console port, and virtual terminal line configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, configure an auxiliary, console, or virtual terminal line.	line {aux \| con \| vty} line-number [ending-line-number]¹
Step 2. List the line configuration commands.	?

¹This command is documented in the "Terminal Lines and Modem Support Commands" chapter in the Router Products Command Reference publication.

The following example shows how to enter line configuration mode for virtual terminal line 3 and list the line configuration commands. The new prompt Router(config-line)# indicates line configuration mode.

Router(config)# line vty 3 <CR>

Router(config-line)# ? 

Line configuration commands:
 access-class            Filter connections based on an IP access list
 activation-character    Define the activation character
 autobaud                Set line to autobaud
 autocommand             Automatically execute an EXEC command
 autohangup              Automatically hangup when last connection closes
 autohost                Automatically connect to a host
 cts-required            Require CTS on line
 data-character-bits     Size of characters being handled
 databits                Set number of data bits per character
 disconnect-character    Define the disconnect character
 dispatch-character      Define the dispatch character
 dispatch-timeout        Set the dispatch timer
 editing                 Enable command line editing
 escape-character        Change the current line's escape character
 exec                    Start an EXEC process
 exec-banner             Enable the display of the EXEC banner
 exec-character-bits     Size of characters to the command exec
 exec-timeout            Set the EXEC timeout
 exit                    Exit from line configuration mode
 flowcontrol             Set the flow control
 help                    Description of the interactive help system
 history                 Enable the command history function
 hold-character          Define the hold character
 length                  Set number of lines on a screen
 location                Enter terminal location description
 lockable                Allow users to lock a line
 login                   Enable password checking
 modem                   Configure the Modem Control Lines
 monitor                 Copy debug output to the current terminal line
 no                      Negate a command or set its defaults
 notify                  Inform users of output from concurrent sessions
 padding                 Set padding for a specified output character
 parity                  Set terminal parity
 password                Set a password
 private             Configuration options that user can set will remain in effect

between terminal sessions
 refuse-message          	Define a refuse banner
 rotary                  Add line to a rotary group
 rxspeed                 Set the receive speed
 session-limit           Set maximum number of sessions
 session-timeout            Set interval for closing connection when there is no input 
traffic
 special-character-bits  Size of the escape (and other special) characters
 speed                   Set the transmit and receive speeds
 start-character         Define the start character
 stop-character          Define the stop character
 stopbits                Set async line stop bits
 telnet                  Telnet protocol-specific configuration
 telnet-transparent      Send a CR as a CR followed by a NULL instead of a CR followed 

by a LF
 terminal-type           Set the terminal type
 transport               Define transport protocols for line
 txspeed                 Set the transmit speeds
 vacant-message          Define a vacant banner
 width                   Set width of the display terminal

The list of commands might vary from this example, depending upon how your router has been configured.

To exit line configuration mode and return to global configuration mode, use the exit command. To exit configuration mode and return to privileged EXEC mode, press Ctrl-Z.

Router Configuration Mode

Router configuration commands configure a routing protocol and always follow a router command. To access and list the router configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, enter router configuration mode.	router [keyword]¹ See the list in the example for keywords.
Step 2. List the router configuration commands.	?

¹This command is documented in the "IP Routing Protocols Commands" chapter in the Router Products Command Reference publication.

To list the available router configuration keywords, enter the router command followed by a space and a question mark (?) at the global configuration prompt:

Router(config)# router ?

 bgp       Border Gateway Protocol (BGP)
 egp       Exterior Gateway Protocol (EGP)
 igrp      Interior Gateway Routing Protocol (IGRP)
 isis      ISO IS-IS
 iso-igrp  IGRP for OSI networks
 ospf      Open Shortest Path First (OSPF)
 rip       Routing Information Protocol (RIP)
 static    Static CLNS Routing

In the following example, the router is configured to support the Routing Information Protocol (RIP). The new prompt is Router(config-router)#.

Router(config)# router rip

Router(config-router)# ?

router configuration commands:
  default-information  Control distribution of default information
  default-metric       Set metric of redistributed routes
  distance             Define an administrative distance
  distribute-list      Filter networks in routing updates
  exit                 Exit from routing protocol configuration mode
  help                 Description of the interactive help system
  neighbor             Specify a neighbor router
  network              Enable routing on an IP network
  no                   Negate or set default values of a command
  offset-list          Add or subtract offset from IGRP, RIP, or HELLO metrics
  passive-interface    Suppress routing updates on an interface
  redistribute         Redistribute information from another routing protocol
  timers               Adjust routing timers

The list of commands might vary slightly from this example, depending upon how your router has been configured.

To exit router configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to privileged EXEC mode, press Ctrl-Z.

IPX-Router Configuration Mode

Internet Packet Exchange (IPX) is a Novell network-layer protocol. To access and list the IPX routing configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, enter IPX-router configuration mode.	ipx router [keyword]¹ See the Novell IPX chapter for keywords.
Step 2. List the IPX-router configuration commands.	?

¹This command is documented in the "Novell IPX Commands" chapter in the Router Products Command Reference publication.

In the following example, IPX RIP routing is configured. The new prompt is Router(config-ipx-router)#.

Router(config)# ipx router rip<CR>

Router(config-ipx-router)# ? 

Novell router configuration commands:
  distribute-list  Filter networks in routing updates
  exit             Exit from IPX routing protocol configuration mode
  help             Description of the interactive help system
  network          Enable routing on an IPX network
  no               Negate or set default values of a command
  redistribute     Enable routing protocol redistribution

To exit IPX-router configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to privileged EXEC mode, press Ctrl-Z.

Route-Map Configuration Mode

Use the route-map configuration mode to configure routing table and source and destination information. To access and list the route-map configuration commands, complete the following tasks:

Task	Command
Step 1. From global configuration mode, enter route-map configuration mode.	route-map [route map tag]¹
Step 2. List the route-map configuration commands.	?

¹This command is documented in the "IP Routing Protocols Commands" chapter in the Router Products Command Reference publication.

In the following example, a route map named arizona1 is configured. The new prompt is Router(config-route-map)#. Enter a question mark (?) to list route-map configuration commands.

Router(config)# route-map arizona1 <CR>

Router(config-route-map)# ? 

Route Map configuration commands:
 exit   Exit from route-map configuration mode
 help   Description of the interactive help system
 match  Match values from routing table
 no     Negate or set default values of a command
 set    Set values in destination routing protocol

To exit route-map configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to privileged EXEC mode, press Ctrl-Z.

ROM Monitor Mode

If your router does not find a valid system image, or if its configuration file is corrupted at startup, the system might enter read-only memory (ROM) monitor mode. From ROM monitor mode, you can boot the router or perform diagnostic tests.

From the Cisco 2000, Cisco 3000, and Cisco 4000, you can also enter ROM monitor mode by entering the reload EXEC command and then pressing the Break key during the first 60 seconds of startup. To save changes to the configuration file, use the write memory command before issuing the reload command.

To access and list the ROM monitor configuration commands, complete the following tasks:

Task	Command
Enter ROM monitor mode from privileged EXEC mode.	reload ¹ Press Break during the first 60 seconds while the system is booting.
List the ROM monitor commands.	?

¹This command is documented in the "System Image, Microcode Image, and Configuration File Load Commands" chapter of the Router Products Command Reference publication.

The ROM monitor prompt is the angle bracket (>):

> ?

$ state      Toggle cache state (? for help)
B [filename] [TFTP Server IP address | TFTP Server Name]
             Load and execute system image from ROM or from TFTP server
C [address]  Continue execution [optional address]
D /S M L V   Deposit value V of size S into location L with modifier M
E /S M L     Examine location L with size S with modifier M
G [address]  Begin execution
H            Help for commands
I            Initialize
K            Stack trace
L [filename] [TFTP Server IP address | TFTP Server Name]
             Load system image from ROM or from TFTP server, but do not
             begin execution
O            Show configuration register option settings
P            Set the break point
S            Single step next instruction
T function   Test device (? for help)
Deposit and Examine sizes may be B (byte), L (long) or S (short).
Modifiers may be R (register) or S (byte swap).
Register names are: D0-D7, A0-A6, SS, US, SR, and PC

To return to user EXEC mode, enter c to continue. To boot the system image file, use the b command (described in the "System Image, Microcode Image, and Configuration File Load Commands" chapter in the Router Products Command Reference publication). For details on other ROM monitor mode commands, refer to the appropriate hardware installation guide.

Get Context-Sensitive Help

The previous sections described the first level of help available with the user interface. Entering a question mark (?) at the system prompt displays a list of commands available for each command mode. You can also get a list of any command's associated keywords and arguments with the context-sensitive help feature.

To get help specific to a command mode, a command, a keyword, or arguments, perform one of the following tasks:

Task	Command
Obtain a brief description of the help system in any command mode.	help
Obtain help for the full set of user-level commands.	full-help
Obtain help for the full set of user-level commands in user EXEC command mode.	terminal full-help¹
Obtain a list of commands that begin with a particular character string.	abbreviated-command-entry?
Complete a partial command name.	abbreviated-command-entry<Tab>
List all commands available for a particular command mode.	?
List a command's associated keywords.	command ?
List a keyword's associated arguments.	command keyword ?

¹This command is documented in the Cisco Access Connection Guide.

When using context-sensitive help, the space (or lack of a space) before the question mark (?) is significant. To obtain a list of commands that begin with a particular character sequence, type in those characters followed immediately by the question mark (?). Do not include a space. This form of help is called word help, because it completes a word for you.

To list keywords or arguments, enter a question mark (?) in place of a keyword or argument. Include a space before the ?. This form of help is called command syntax help, because it reminds you which keywords or arguments are applicable based on the command, keywords, and arguments you already have entered.

You can abbreviate commands and keywords to the number of characters that allow a unique abbreviation. For example, you can abbreviate the show command to sh.

Enter the help command (which is available in any command mode) for a brief description of the help system:

Router# help

Help may be requested at any point in a command by entering

a question mark '?'. If nothing matches, the help list will

be empty and you must back up until entering a '?' shows the

available options.

Two styles of help are provided:

1. Full help is available when you are ready to enter a

   command argument (e.g. 'show ?') and describes each possible

   argument.

2. Partial help is provided when an abbreviated argument is entered

   and you want to know what arguments match the input

   (e.g. 'show pr?'.)

As described in the help command output, you can enter a partial command name and a question mark (?) to obtain a list of commands beginning with a particular character set. See "Complete a Partial Command Name" later in this chapter for more detail.

The following example illustrates how the context-sensitive help feature enables you to create an access list from configuration mode. First enter the letters co at the system prompt followed by a question mark (?). Do not leave a space between the last letter and the question mark (?). The system provides the commands that begin with co.

Router# co?

configure  connect  copy

Enter the configure command followed by a space and a question mark (?) to list the command's keywords and a brief explanation:

Router# configure ?

  memory    Configure from NV memory
  network   Configure from a TFTP network host
  terminal  Configure from the terminal
  <cr>

Enter the terminal keyword to enter configuration mode from the terminal:

Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#

Enter the access-list command followed by a space and a question mark (?) to list the command's keywords:

Router(config)# access-list ?

  <1-99>       IP standard access list
  <100-199>    IP extended access list
  <1000-1099>  IPX SAP access list
  <1100-1199>  Extended 48-bit MAC address access list
  <200-299>    Protocol type-code access list
  <300-399>    DECnet access list
  <400-499>    XNS standard access list
  <500-599>    XNS extended access list
  <600-699>    Appletalk access list
  <700-799>    48-bit MAC address access list
  <800-899>    IPX standard access list
  <900-999>    IPX extended access list

Enter the access list number 99 and then enter another question mark (?) to see the arguments that apply to the keyword and brief explanations:

Router(config)# access-list 99 ?

  deny    Specify packets to reject
  permit  Specify packets to forward

Enter the deny argument followed by a question mark (?) to list additional options:

Router(config)# access-list 99 deny ?

  A.B.C.D  Address to match

Enter the IP address followed by a question mark (?) to list additional options:

Router(config)# access-list 99 deny 131.108.134.0 ?

  A.B.C.D  Mask of bits to ignore
  <cr>

The <cr> symbol appears in the list, indicating that one of your options is to press Return to execute the command. The other option is to add a wildcard mask. Enter the wildcard mask followed by a question mark (?) to list further options.

Router(config)# access-list 99 deny 131.108.134.0 0.0.0.255 ?
<cr>
 
Router(config)# access-list 99 deny 131.108.134.0 0.0.0.255

The <cr> symbol by itself indicates there are no more keywords or arguments. Press Return to execute the command. The system adds an entry to access list 99 that denies access to all hosts on subnet 131.108.134.0.

Check Command Syntax

The user interface provides syntax checking in the form of an error location indicator (^). The ^ symbol appears at the point in the command string where you have entered an incorrect command, keyword, or argument. The error location indicator and interactive help system allow you to easily find and correct syntax errors.

In the following example, suppose you want to set the router clock. First, use context-sensitive help to check the syntax for setting the clock.

Router# clock ?

  set  Set the time and date
Router# clock

The help output shows that the set keyword is required. Next, check the syntax for entering the time:

Router# clock set ?

hh:mm:ss   Current time
Router# clock set

Enter the current time:

Router# clock set 13:32:00

% Incomplete command.

The system indicates that you need to provide additional arguments to complete the command. Press Ctrl-P (see the next section, "Use the Command History Features") to automatically repeat the previous command entry. Then add a space and question mark (?) to reveal the additional arguments:

Router# clock set 13:32:00 ?

  <1-31>     Day of the month
  January    Month of the year
  February
  March
  April
  May
  June
  July
  August
  September
  October
  November
  December

Now you can complete the command entry:

Router# clock set 13:32:00 23 February 93

                                       ^
% Invalid input detected at '^' marker.

The caret symbol (^) and help response indicate an error at 93. To list the correct syntax, enter the command up to the point where the error occurred and then enter a question mark (?):

Router# clock set 13:32:00 23 February ?

  <1993-2035> Year
Router# clock set 13:32:00 23 February

Enter the year using the correct syntax and press Return to execute the command.

Router# clock set 13:32:00 23 February 1993

Use the Command History Features

With the current software release, the user interface provides a history or record of commands you have entered. This feature is particularly useful for recalling long or complex commands or entries, including access lists. With the command history feature, you can complete the tasks in the following sections:

Set the Command History Buffer Size

By default, the system records ten command lines in its history buffer. To set the number of command lines the system will record during the current terminal session, complete the following task in EXEC mode:

Task	Command
Enable the command history feature for the current terminal session.	terminal history [size number-of-lines]¹

¹This command is documented in the Cisco Access Connnection Guide.

The terminal history no size command resets to default.

To configure the number of command lines the system will record, complete the following task in line configuration mode:

Task	Command
Enable the command history feature.	history [size number-of-lines]¹

¹The no history command resets to default.

Recall Commands

To recall commands from the history buffer, perform one of the following tasks:

Task	Key Sequence/Command
Recall commands in the history buffer, beginning with the most recent command. Repeat the key sequence to recall successively older commands.	Press Ctrl-P or the up arrow key.¹
Return to more recent commands in the history buffer after recalling commands with Ctrl-P or the up arrow key. Repeat the key sequence to recall successively more recent commands.	Press Ctrl-N or the down arrow key.¹
While in EXEC mode, list the commands you have just entered.	show history

¹The arrow keys function only on ANSI-compatible terminals such as VT100s.

Disable the Command History Feature

The command history feature is automatically enabled. To disable it during the current terminal session, complete the following task in EXEC mode:

Task	Command
Disable the command history feature for the current session.	terminal no history¹

¹This command is documented in the Cisco Access Connnection Guide.

To configure a specific line so that the command history feature is disabled, complete the following task in line configuration mode:

Task	Command
Configure the line so that the command history feature is disabled.	no history

Use the Editing Features

The current software release includes an enhanced editing mode that provides a set of editing key functions similar to those of the Emacs editor.

You can enter commands in uppercase, lowercase, or a mix of both. Only passwords are casesensitive. You can abbreviate commands and keywords to the number of characters that allow a unique abbreviation. For example, you can abbreviate the show command to sh. After entering the command line at the system prompt, press the Return key to execute the command.

The following subsections are included in this section:

Enable Enhanced Editing Mode

Although enhanced editing mode is automatically enabled with the current software release, you can disable it and revert to the editing mode of previous software releases. See the section "Disable Enhanced Editing Mode" later in this chapter.

To reenable the enhanced editing mode for the current terminal session, complete the following task in EXEC mode:

Task	Command
Enable the enhanced editing features for the current terminal session.	terminal editing ¹

¹This command is documented in the Cisco Access Connection Guide.

To reconfigure a specific line to have enhanced editing mode, complete the following task in line configuration mode:

Task	Command
Enable the enhanced editing features.	editing

Move Around on the Command Line

Perform the following tasks to move the cursor around on the command line for corrections or changes:

Task	Keystrokes
Move the cursor back one character.	Press Ctrl-B or press the left arrow key.¹
Move the cursor forward one character.	Press Ctrl-F or press the right arrow key.¹
Move the cursor to the beginning of the command line.	Press Ctrl-A.
Move the cursor to the end of the command line.	Press Ctrl-E.
Move the cursor back one word.	Press Esc-B.
Move the cursor forward one word.	Press Esc-F.

¹The arrow keys function only on ANSI-compatible terminals such as VT100s.

Complete a Partial Command Name

If you cannot remember a complete command name, you can use the Tab key to allow the system to complete a partial entry. To do so, perform the following task:

Task	Keystrokes
Recall a complete command name.	Enter the first few letters and press the Tab key.

If your keyboard does not have a Tab key, press Ctrl-I instead.

In the following example, when you enter the letters conf and press the Tab key, the system provides the complete command:

Router# conf<Tab>

Router# configure

If you enter a set of characters that could indicate more than one command, the system beeps to indicate an error. Enter a question mark (?) to obtain a list of commands that begin with that set of characters. Do not leave a space between the last letter and the question mark (?).

For example, there are three commands in privileged mode that start with co. To see what they are, type co? at the privileged EXEC prompt:

Router# co?

configure  connect  copy
Router# co

Paste in Buffer Entries

The system provides a buffer that contains the last ten items you deleted. You can recall these items and paste them in the command line by performing the following task:

Task	Keystrokes
Step 1. Recall the most recent entry in the buffer.	Press Ctrl-Y.
Step 2. Recall the next buffer entry.	Press Esc-Y.

The buffer contains only the last ten items you have deleted or cut. If you press Esc-Y more than ten times, you will cycle back to the first buffer entry.

Edit Command Lines that Wrap

The new editing command set provides a wraparound feature for commands that extend beyond a single line on the screen. When the cursor reaches the right margin, the command line shifts ten spaces to the left. You cannot see the first ten characters of the line, but you can scroll back and check the syntax at the beginning of the command. To scroll back, perform the following task:

Task	Keystrokes
Return to the beginning of a command line to verify that you have entered a lengthy command correctly.	Press Ctrl-B or the left arrow key repeatedly until you scroll back to the beginning of the command entry, or press Ctrl-A to return directly to the beginning of the line.¹

¹The arrow keys function only on ANSI-compatible terminals such as VT100s.

In the following example, the access-list command entry extends beyond one line. When the cursor first reaches the end of the line, the line is shifted ten spaces to the left and redisplayed. The dollar sign ($) indicates that the line has been scrolled to the left. Each time the cursor reaches the end of the line, the line is again shifted ten spaces to the left.

Router(config)# access-list 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1
Router(config)# $ 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1.20 255.25
Router(config)# $t tcp 131.108.2.5 255.255.255.0 131.108.1.20 255.255.255.0 eq
Router(config)# $108.2.5 255.255.255.0 131.108.1.20 255.255.255.0 eq 45

When you have completed the entry, press Ctrl-A to check the complete syntax before pressing the Return key to execute the command. The dollar sign ($) appears at the end of the line to indicate that the line has been scrolled to the right:

Router(config)# access-list 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1$

The router assumes you have a terminal screen that is 80 columns wide. If you have a width other than that, use the terminal width command to tell the router the correct width of your terminal.

Use line wrapping in conjunction with the command history feature to recall and modify previous complex command entries. See the section "Recall Commands" earlier in this chapter for information about recalling previous command entries.

Delete Entries

Perform any of the following tasks to delete command entries if you make a mistake or change your mind:

Task	Keystrokes
Erase the character to the left of the cursor.	Press the Delete or Backspace key.
Delete the character at the cursor.	Press Ctrl-D.
Delete all characters from the cursor to the end of the command line.	Press Ctrl-K.
Delete all characters from the cursor to the beginning of the command line.	Press Ctrl-U or Ctrl-X.
Delete the word to the left of the cursor.	Press Ctrl-W.
Delete from the cursor to the end of the word.	Press Esc-D.

Scroll Down a Line or a Screen

When you use the help facility to list the commands available in a particular mode, the list is often longer than the terminal screen can display. In such cases, a ---More--- prompt is displayed at the bottom of the screen. To view the next line or screen, complete the following tasks:

Task	Keystrokes
Scroll down one line.	Press the Return key.
Scroll down one screen.	Press the Space bar.

Note The ---More--- prompt is used for any output that has more lines than can be displayed on the terminal screen, including show command output. You can use the keystrokes listed above whenever you see the ---More--- prompt.

Redisplay the Current Command Line

If you are entering a command and the system suddenly sends a message to your screen, you can easily recall your current command line entry. To do so, perform the following task:

Task	Keystrokes
Redisplay the current command line.	Press Ctrl-L or Ctrl-R.

Transpose Mistyped Characters

If you have mistyped a command entry, you can transpose the mistyped characters by performing the following task:

Task	Keystrokes
Transpose the character to the left of the cursor with the character located at the cursor.	Press Ctrl-T.

Control Capitalization

You can capitalize or lowercase words or capitalize a set of letters with simple keystroke sequences. To do so, perform the following task:

Task	Keystrokes
Capitalize the word at the cursor.	Press Esc-C.
Change the word at the cursor to lowercase.	Press Esc-L.
Capitalize letters from the cursor to the end of the word.	Press Esc-U.

Designate a Keystroke as a Command Entry

Sometimes you might want to use a particular keystroke as an executable command, perhaps as a shortcut. Complete the following task to insert a system code for this purpose:

Task	Keystrokes
Insert a code to indicate to the system that the keystroke immediately following should be treated as a command entry, not an editing key.	Press Ctrl-V or Esc-Q.

Disable Enhanced Editing Mode

To disable enhanced editing mode and revert to the editing mode of software releases before 9.21, perform the following task in EXEC mode:

Task	Command
Disable the enhanced editing features for the local line.	terminal no editing¹

¹This command is documented in the Cisco Access Connection Guide.

You might want to disable enhanced editing if you have prebuilt scripts; for example, scripts that do not interact well when enhanced editing is enabled. You can reenable enhanced editing mode with the terminal editing command.

The editing keys and functions of software releases before 9.21 are listed in Table 2-2.

Table 2-2: Editing Keys and Functions for Software Release 9.1 and Earlier

Key Function

Delete or Backspace

Erases the character to the left of the cursor.

Ctrl-W

Erases a word.

Ctrl-U

Erases a line.

Ctrl-R

Redisplays a line.

Ctrl-Z

Ends configuration mode and returns to the EXEC prompt.

Return

Executes single-line commands.

End a Session

After using the setup command or other configuration commands, exit the router and close the console port connection to return to the Telnet prompt, from which you can quit the session.

To end a session, perform the following steps:

Task	Command
Step 1. Exit the router and close the console port connection.	Press Ctrl-]
Step 2. Quit the Telnet session.	quit

Refer to the Cisco Access Connection Guide for more information on exiting sessions and closing connections.

Key	Function
Delete or Backspace	Erases the character to the left of the cursor.
Ctrl-W	Erases a word.
Ctrl-U	Erases a line.
Ctrl-R	Redisplays a line.
Ctrl-Z	Ends configuration mode and returns to the EXEC prompt.
Return	Executes single-line commands.

Table of Contents