|
|
This chapter describes the function and displays the syntax of each SDLLC and QLLC command. For more information about defaults and usage guidelines, see the corresponding chapter of the Router Products Command Reference publication.
[no] qllc largest-packet virtual-mac-addr max-size
Use the qllc largest-packet interface configuration command to indicate the maximum size of the SNA packet that can be sent or received on an X.25 interface configured for QLLC conversion. Use the no form of the command to restore the default largest packet size.
| virtual-mac-addr | Virtual MAC address associated with the remote X.25 device, as defined using the x25 map or x25 pvc commands. This address is written as a dotted triple of four-digit hexadecimal numbers. |
| max-size | Maximum size, in bytes, of the SNA packet that can be sent or received on the X.25 interface configured for QLLC conversion. This value agrees with the value configured in the remote SNA device. The valid range is 0 through 1024. |
[no] qllc partner virtual-mac-addr mac-addr
Use the qllc partner interface configuration command to enable a router configured for QLLC conversion to open a connection to the local Token Ring device on behalf of the remote X.25 device when an incoming call is received. Use the no version of this command to disable this capability.
| virtual-mac-addr | Virtual MAC address associated with the remote X.25 device, as defined using the x25 map or x25 pvc command. This address is written as a dotted triple of four-digit hexadecimal numbers. |
| mac-addr | 48-bit MAC address of the Token Ring host that will communicate with the remote X.25 device. |
[no] qllc sap virtual-mac-addr ssap dsap
Use the qllc sap interface configuration command to associate a SAP value other than the default SAP value with a serial interface configured for X.25 communication and QLLC conversion. The no form of this command returns this SAP value to its default state.
| virtual-mac-addr | Virtual MAC address associated with the remote X.25 device, as defined using the x25 map or x25 pvc command. |
| ssap | Source SAP value. It can be a decimal number in the range 2 through 254. |
| dsap | Destination SAP value. It can be a decimal number in the range 2 through 254. |
[no] qllc srb virtual-mac-addr srn trn
Use the qllc srb interface configuration command to enable the use of QLLC conversion on a serial interface configured for X.25 communication. The no version of this command disables QLLC conversion on the interface.
| virtual-mac-addr | Virtual MAC address associated with the remote X.25 device, as defined using the x25 map or x25 pvc command. It can be 1 to 15 digits long. |
| srn | Source ring number. This value defines a virtual ring for all of the remote X.25 devices attached to the QLLC interface. Any number of QLLC conversion connections using the same X.25 serial interface can share a common source ring. However, this source ring must be a unique hexadecimal ring number within the source-bridged network. |
| trn | Target ring number. It must be a virtual ring group that has been defined with the source-bridge ring-group command. If the router has only one Token Ring interface and is bridging from the remote X.25 devices to this interface, then trn is the number of the ring on that Token Ring interface. If the router has several Token Ring interfaces and interconnects them by means of the source-bridge ring-group command, then trn is the number of that virtual ring group, as assigned using the source-bridge ring-group global configuration command. |
[no] qllc xid virtual-mac-addr xid
Use the qllc xid interface configuration command to associate an XID value with the remote X.25 device that communicates through the router using QLLC conversion. The no form of this command disables XID processing for this address.
| virtual-mac-addr | Virtual MAC address associated with the remote X.25 device, as defined using the x25 map or x25 pvc command. |
| xid | Combined XID IDBLK and XID IDNUM you are associating with the X.25 device at this X.121 address. This hexadecimal value must be four bytes (eight digits) in length. |
[no] sdllc partner mac-address sdlc-address
Use the sdllc partner interface configuration command to enable device-initiated connections for SDLLC. This command must be specified for the serial interface that links to the serial line device. Use the no form of this command to cancel the original instruction.
| mac-address | 48-bit MAC address of the Token Ring host |
| sdlc-address | SDLC address of the serial device that will communicate with the Token Ring host |
[no] sdllc ring-largest-frame value
Use the sdllc ring-largest-frame interface configuration command to indicate the largest I-frame size that can be sent to or received from the LLC2 primary station. Use the no form of this command to return to the default.
| value | Frame size in bytes. The default is 516 bytes. |
[no] sdllc sap sdlc-address ssap dsap
Use the sdllc sap interface configuration command to associate a service access point (SAP) value other than the default SAP value with a serial interface configured for SDLLC. Use the no form of this command to return this SAP value to 4, the default value.
| sdlc-address | Virtual MAC address associated with the remote SDLC device. |
| ssap | Source SAP value. It must be in the range 1 through 254. |
| dsap | Destination SAP value. It must be in the range 1 through 254. |
[no] sdllc sdlc-largest-frame address value
Use the sdllc sdlc-largest-frame interface configuration command to indicate the largest information frame (I-frame) size that can be sent or received by the designated SDLC station. Use the no form of this command to return to 265, the default value.
| address | Address of the SDLC station that will communicate with the Token Ring host |
| value | Largest frame size that can be sent or received by this SDLC station |
[no] sdllc traddr xxxx.xxxx.xx00 lr bn tr
Use the sdllc traddr interface configuration command to enable the use of SDLLC Media Translation on a serial interface. The address specified is a MAC address to be assigned to the serial station. Use the no form of this command to disable SDLLC Media Translation on the interface.
| xxxx.xxxx.xx00 | MAC address to be assigned to the serial interface |
| lr | SDLLC virtual ring number |
| bn | SDLLC bridge number |
| tr | SDLLC target ring number |
[no] sdllc xid address xxxxxxxx
Use the sdllc xid interface configuration command to specify an exchanged ID (XID) value appropriate for the designated SDLC station associated with this serial interface. Use the no form of this command to disable XID processing for this address.
| address | Address of the SDLC station associated with this interface. |
| xxxxxxxx | XID the router will use to respond to XID requests the router receives on the Token Ring (LLC2) side of the connection. This value must be 4 bytes (8 digits) long and is specified with hexadecimal digits. |
show interfaces
Use the show interfaces privileged EXEC command to display the SDLC information for a given SDLC interface.
show qllc
Use the show qllc EXEC command to display the current state of any QLLC connections.
show sdllc local-ack
Use the show sdllc local-ack privileged EXEC command to display the current state of any current local acknowledgment connections and any configured passthrough rings.
[no] source-bridge fst-peername local-interface-address
Use the source-bridge fst-peername global configuration command to set up a Fast-Sequenced Transport (FST) peer name. Use the no form of this command to disable the IP address assignment.
| local-interface-address | IP address to assign to the local router |
[no] source-bridge qllc-local-ack
Use the source-bridge qllc-local-ack global configuration command to enable or disable QLLC local acknowledgment for all of the router's QLLC conversion connection. The no form of the command disables this capability.
source-bridge remote-peer ring-group fst ip-address [lf size]
[version number]
no source-bridge remote-peer ring-group fst ip-address
Use the source-bridge remote-peer fst global configuration command to specify a Fast-Sequenced Transport (FST) encapsulation connection. Use the no form of the command to disable the previous assignments.
| ring-group | Ring group number. This ring group number must match the number you have specified with the source-bridge ring-group command. The valid range is 1 through 4095. |
| ip-address | IP address of the remote peer with which the router will communicate. |
| lf size | (Optional) Maximum size frame to be sent to this remote peer. The router negotiates all transit routes down to this size or lower. Use this argument to prevent timeouts in end hosts by reducing the amount of data they have to transmit in a fixed interval. The legal values for this argument are 516, 1500, 2052, 4472, 8144, 11407, and 17800 bytes. |
| version number | (Optional) Forces RSRB protocol version number for the remote peer. Because all FST peers support version 2 RSRB, the version keyword is always specified. |
source-bridge remote-peer ring-group interface interface-name
[mac-address] [lf size]
no source-bridge remote-peer ring-group interface interface-name
Use the source-bridge remote-peer interface global configuration command when specifying a point-to-point direct encapsulation connection. Use the no form of this command to disable previous interface assignments.
| ring-group | Ring group number. This ring group number must match the number you have specified with the source-bridge ring-group command. The valid range is 1 through 4095. |
| interface-name | Name of the router's serial interface over which to send source-route bridged traffic. |
| mac-address | (Optional) MAC address for the interface you specify using the interface-name argument. This argument is required for nonserial interfaces. You can obtain the value of this MAC address by using the show interface command, and then scanning the display for the interface specified by interface-name. |
| lf size | (Optional) Maximum size frame to be sent to this remote peer. The router negotiates all transit routes down to this size or lower. This argument is useful in preventing timeouts in end hosts by reducing the amount of data they have to transmit in a fixed interval. The legal values for this argument are 516, 1500, 2052, 4472, 8144, 11407, and 17800 bytes. |
source-bridge remote-peer ring-group tcp ip-address [lf size]
[local-ack] [priority]
no source-bridge remote-peer ring-group tcp ip-address
Use the source-bridge remote-peer tcp global configuration command to identify the IP address of a peer in the ring group with which to exchange source-bridge traffic using TCP. Use the no form of this command to remove a remote peer for the specified ring group.
| ring-group | Ring group number. This ring group number must match the number you have specified with the source-bridge ring-group command. The valid range is 1 through 4095. |
| ip-address | IP address of the remote peer with which the router will communicate. |
| lf size | (Optional) Maximum size frame to be sent to this remote peer. The router negotiates all transit routes down to this size or lower. Use this argument to prevent timeouts in end hosts by reducing the amount of data they have to transmit in a fixed interval. The valid values for this argument are 516, 1500, 2052, 4472, 8144, 11407, and 17800 bytes. |
| local-ack | (Optional) LLC2 sessions destined for a specific remote peer are to be locally terminated and acknowledged. Local acknowledgment should be used for LLC2 sessions going to this remote peer. |
| priority | (Optional) Enables prioritization over a TCP network. You must specify the keyword local-ack earlier in the same source-bridge remote-peer command. The keyword priority is a prerequisite for features such as SNA class of service and SNA LU address prioritization over a TCP network. |
[no] source-bridge ring-group ring-group
Use the source-bridge ring-group global configuration command to define or remove a ring group from the router configuration. Use the no form of this command to cancel previous assignments.
| ring-group | Ring group number. The valid range is 1 through 4095. |
[no] source-bridge sdllc-local-ack
Use the source-bridge sdllc-local-ack global configuration command to activate Local Acknowledgment for SDLLC sessions on a particular interface. Use the no form of this command to deactivate local acknowledgment for SDLLC sessions.
[no] x25 map qllc virtual-mac-addr x121-addr
Use the x25 map qllc interface configuration command to associate a virtual MAC address with the X.121 address of the remote X.25 device with which you plan to communicate using QLLC conversion. The no form of this command disables QLLC conversion to this X.121 address.
| virtual-mac-addr | Virtual MAC address you are associating with the X.25 device at this X.121 address. The router will accept explorer and data packets destined for this MAC address. It can be from 1 to 15 digits long. |
| x121-addr | X.121 address of the remote X.25 device you are associating with this virtual MAC address. It can be from 1 to 15 digits long. |
[no] x25 pvc circuit qllc virtual-mac-addr
Use the x25 pvc interface configuration command to associate a virtual MAC address with a permanent virtual circuit (PVC) for communication using QLLC conversion. The no form of this command removes the association.
| circuit | PVC you are associating with the virtual MAC address. This must be lower than any number assigned to switched virtual circuits. |
| virtual-mac-addr | Virtual MAC address you are associating with the X.25 device at this pvc. The router will accept explorer and data packets destined for this MAC address. This virtual MAC address must match the virtual MAC address you specified using the x25 map qllc command. |
|
|