|
|
Novell Internet Packet Exchange (IPX) is derived from the Xerox Network Systems (XNS) Internet Datagram Protocol (IDP). One major difference between IPX and XNS is that they do not always use the same Ethernet encapsulation format. A second difference is that IPX uses Novell's proprietary Service Advertisement Protocol (SAP) to advertise special network services.
Our implementation of Novell's IPX protocol has been certified as providing full IPX router functionality. Our router connects Ethernet, Token Ring, and FDDI networks, either directly or through high-speed serial lines (56 kbps to T1 speeds), X.25, or Frame Relay. The Cisco X.25 and T1 support currently is not compatible with Novell. This means that our routers must be used on both ends of T1 and X.25 circuits.
Use the commands in this chapter to configure and monitor Novell IPX networks. For IPX configuration information and examples, refer to the "Configuring Novell IPX" chapter in the Router Products Configuration Guide.
To define a standard IPX access list, use the standard version of the access-list global configuration command. To remove a standard access list, use the no form of this command.
access-list access-list-number {deny | permit} source-network[.source-node| access-list-number | Number of the access list. This is a decimal number from 800 to 899. |
| deny | Denies access if the conditions are matched. |
| permit | Permits access if the conditions are matched. |
| source-network | Number of the network from which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks.
You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. |
| source-node | (Optional) Node on source-network from which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). |
| source-node-mask | (Optional) Mask to be applied to source-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask. |
| destination-network | (Optional) Number of the network to which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks.
You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. |
| destination-node | (Optional) Node on destination-network to which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). |
| destination-node-mask | (Optional) Mask to be applied to destination-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask. |
No access lists are predefined.
Global configuration
Standard IPX access lists filter on the source network. All other parameters are optional.
Use the ipx access-group command to assign an access list to an interface. You can apply only one extended or one standard access list to an interface. The access list filters all outgoing packets on the interface.
To delete a standard access list, specify the minimum number of keywords and arguments needed to delete the proper access list. For example, to delete the entire access list, use the following command:
no access-list access-list-numberTo delete the access list for a specific network, use the following command:
no access-list access-list-number {deny | permit} source-networkThe following example denies access to traffic from all IPX networks (-1) to destination network 2:
access-list 800 deny -1 2
The following example denies access to all traffic from IPX address 1.0000.0c00.1111:
access-list 800 deny 1.0000.0c00.1111
The following example denies access from all nodes on network 1 that have a source address beginning with 0000.0c:
access-list 800 deny 1.0000.0c00.0000 0000.00ff.ffff
The following example denies access from source address 1111.1111.1111 on network 1 to destination address 2222.2222.2222 on network 2:
access-list 800 deny 1.1111.1111.1111 0000.0000.0000 2.2222.2222.2222 0000.0000.0000
access-list 800 deny 1.1111.1111.1111 2.2222.2222.2222
A dagger (+) indicates that the command is documented in another chapter.
access-list (extended)
ipx access-group
ipx input-network-filter
ipx output-network-filter
ipx router-filter
priority-list protocol +
To define an extended Novell IPX access list, use the extended version of the access-list global configuration command. To remove an extended access list, use the no form of this command.
access-list access-list-number {deny | permit} protocol [source-network][[[.source-node]| access-list-number | Number of the access list. This is a decimal number from 900 to 999. |
| deny | Denies access if the conditions are matched. |
| permit | Permits access if the conditions are matched. |
| protocol | Number of an IPX protocol type, in decimal. This also is sometimes referred to as the packet type. Table 19-1 in the "Usage Guidelines" section lists some IPX protocol numbers. |
| source-network | (Optional) Number of the network from which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks.
You do not need to specify leading zeros in the network number; for example, for the network number 000000AA, you can just enter AA. |
| source-node | (Optional) Node on source-network from which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). |
| source-network-mask | (Optional) Mask to be applied to source-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask.
The mask must immediately be followed by a period, which must in turn immediately be followed by source-node-mask. |
| source-node-mask | (Optional) Mask to be applied to source-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask. |
| source-socket | Socket number from which the packet is being sent, in hexadecimal. Table 19-2 in the "Usage Guidelines" section lists some IPX socket numbers. |
| destination-network | (Optional) Number of the network to which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks.
You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. |
| destination-node | (Optional) Node on destination-network to which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). |
| destination-network-mask | (Optional) Mask to be applied to destination-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask.
The mask must immediately be followed by a period, which must in turn immediately be followed by destination-node-mask. |
| destination-node-mask | (Optional) Mask to be applied to destination-node. This is a
48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask. |
| destination-socket | (Optional) Socket number to which the packet is being sent, in hexadecimal. Table 19-2 in the "Usage Guidelines" section lists some IPX socket numbers. |
No access lists are predefined.
Global configuration
Extended IPX access lists filter on protocol type. All other parameters are optional.
If a network mask is used, all other fields are required.
Use the ipx access-group command to assign an access list to an interface. You can apply only one extended or one standard access list to an interface. The access list filters all outgoing packets on the interface.
Table 19-1 lists some IPX protocol numbers. Table 19-2 lists some IPX socket numbers. For additional information about IPX protocol numbers and socket numbers, contact Novell.
| IPX Protocol Number (Decimal) | Protocol (Packet Type) |
|---|---|
| -1 | Wildcard; matches any packet type |
| 0 | Could be any protocol; refer to the socket number to determine the packet type |
| 1 | Routing Information Protocol (RIP) |
| 4 | Service Advertisement Protocol (SAP) |
| 5 | Sequenced Packet Exchange (SPX) |
| 17 | NetWare Core Protocol (NCP) |
| 20 | IPX NetBIOS |
| IPX Socket Number (Hexadecimal) | Socket |
|---|---|
| 0 | All sockets, wild card used to match all sockets |
| 451 | NetWare Core Protocol (NCP) process |
| 452 | Service Advertisement Protocol (SAP) process |
| 453 | Routing Information Protocol (RIP) process |
| 455 | Novell NetBIOS process |
| 456 | Novell diagnostic packet |
| 457 | Novell serialization socket |
| 4000-7FFF | Dynamic sockets; used by workstations for interaction with file servers and other network servers |
| 8000-FFFF | Well-known sockets as assigned by Novell |
To delete an extended access list, specify the minimum number of keywords and arguments needed to delete the proper access list. For example, to delete the entire access list, use the following command:
no access-list access-list-numberTo delete the access list for a specific protocol, use the following command:
no access-list access-list-number {deny | permit} protocolThe following example denies access to all RIP packets (protocol number 1) from socket 453 (RIP process socket) on source network 1 that are destined for socket 453 on network 2. It permits all other traffic.
access-list 900 deny 1 453 2 453
access-list 900 permit 0 -1 0 -1 0
The following example permits type 2 packets from any socket on network 10 to access any sockets on any nodes on networks 1000 through 100F. It denies all other traffic (with an implicit deny all):
access-list 910 permit 20 10.0000.0C00.0000 0000.0000.FFFF 0
1000.0000.0000.0000 F.FFFF.FFFF.FFFF 0
A dagger (+) indicates that the command is documented in another chapter.
access-list (standard)
ipx access-group
ipx input-network-filter
ipx output-network-filter
ipx router-filter
priority-list protocol +
To define an access list for filtering Service Advertisement Protocol (SAP) requests, use the SAP filtering form of the access-list global configuration command. To remove the access list, use the no form of this command.
access-list access-list-number {deny | permit} network[.node] [network.node-mask]| access-list-number | Number of the SAP access list. This is a decimal number from 1000 to 1099. |
| deny | Denies access if the conditions are matched. |
| permit | Permits access if the conditions are matched. |
| network | Network number. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks.
You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. |
| node | (Optional) Node on network. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). |
| network.node-mask | (Optional) Mask to be applied to network and node. Place ones in the bit positions to be masked. |
| service-type | (Optional) Service type on which to filter. This is a hexadecimal number. A value of 0 means all services.
Table 19-3 in the "Usage Guidelines" section lists examples of service types. |
| server-name | (Optional) Name of the server providing the specified service type. This can be any contiguous string of printable ASCII characters. Use double quotation marks (" ") to enclose strings containing embedded spaces. You can use an asterisk (*) at the end of the name as a wildcard to match one or more trailing characters. |
No access lists are predefined.
Global configuration
When configuring SAP filters for NetWare 3.11 and later servers, use the server's internal network and node number (the node number is always 0000.0000.0001) as its address in the access-list command. Do not use the network.node address of the particular interface board.
Table 19-3 lists some sample IPX SAP types. For more information about SAP types, contact Novell.
| Service Type (Hexadecimal) | Description |
|---|---|
| 1 | User |
| 2 | User group |
| 3 | Print server queue |
| 4 | File server |
| 5 | Job server |
| 7 | Print server |
| 9 | Archive server |
| A | Queue for job servers |
| 21 | NAS SNA gateway |
| 2D | Time Synchronization VAP |
| 2E | Dynamic SAP |
| 47 | Advertising print server |
| 4B | Btrieve VAP 5.0 |
| 4C | SQL VAP |
| 7A | TES--NetWare for VMS |
| 98 | NetWare access server |
| 9A | Named Pipes server |
| 9E | Portable NetWare--UNIX |
| 111 | Test server |
| 166 | NetWare management (Novell's Network Management Station [NMS]) |
| 26A | NetWare management (NMS console) |
To delete a SAP access list, specify the minimum number of keywords and arguments needed to delete the proper access list. For example, to delete the entire access list, use the following command:
no access-list access-list-numberTo delete the access list for a specific network, use the following command:
no access-list access-list-number {deny | permit} networkThe following access list blocks all access to a file server (service type 4) on the directly attached network by resources on other Novell networks, but allows access to all other available services on the interface:
access-list 1001 deny -1 4
access-list 1001 permit -1
A dagger (+) indicates that the command is documented in another chapter.
ipx input-sap-filter
ipx output-gns-filter
ipx output-sap-filter
ipx router-sap-filter
priority-list protocol +
To delete all entries in the accounting database when IPX accounting is enabled, use the clear ipx accounting EXEC command.
clear ipx accounting [checkpoint]| checkpoint | (Optional) Clears the checkpointed database. |
EXEC
Specifying the clear ipx accounting command with no keywords deletes all entries in the active database.
You can also delete all entries in the checkpointed database by issuing the clear ipx accounting command twice in succession.
The following example clears all entries in the active database:
clear ipx accounting
ipx accounting
ipx accounting-list
ipx accounting-threshold
ipx accounting-transits
show ipx accounting
To delete entries from the IPX fast-switching cache, use the clear ipx cache EXEC command.
clear ipx cacheThis command has no arguments or keywords.
EXEC
The clear ipx cache command clears entries used for fast switching, autonomous switching, and SSE fast switching.
The following example deletes all entries from the IPX fast-switching cache:
clear ipx cache
ipx route-cache
show ipx cache
To delete routes from the IPX routing table, use the clear ipx route EXEC command.
clear ipx route [network | *]| network | (Optional) Number of the network whose routing table entry you want to delete. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. |
| * | (Optional) Deletes all routes in the routing table. |
EXEC
The following example clears the entry for network 3 from the IPX routing table:
clear ipx route 3
show ipx route
To have the Cisco 7000 series route processor recompute the entries in the IPX SSE fast-switching cache, use the clear ipx sse EXEC command.
clear ipx sseThis command has no arguments or keywords.
EXEC
Recomputing the entries in the RP's SSE fast-switching cache also updates the SSP's fast-switching cache.
The following example recomputes the entries in the IPX SSE fast-switching cache:
clear ipx sse
ipx route-cache
To reinitialize the route processor on the Cisco 7000 series, use the clear sse EXEC command.
clear sseThis command has no arguments or keywords.
Disabled
EXEC
The silicon switching engine (SSE) is on the Silicon Switch Processor (SSP) board in the Cisco 7000 series.
The following example causes the route processor to be reinitialized:
clear sse
To filter networks received in updates, use the distribute-list in router configuration command. To change or cancel the filter, use the no form of this command.
distribute-list access-list-number in [interface-name]| access-list-number | Standard IPX access list number in the range 800 to 899. The list explicitly specifies which networks are to be received and which are to be suppressed. |
| in | Applies the access list to incoming routing updates. |
| interface-name | (Optional) Interface on which the access list should be applied to incoming updates. If no interface is specified, the access list is applied to all incoming updates. |
Disabled
Router configuration
The following example causes only two networks--network 2 and network 3--to be accepted by an Enhanced IGRP routing process:
access-list 800 permit 2
access-list 800 permit 3
access-list 800 deny -1
!
ipx router eigrp 100
network 3
distribute-list 800 in
access-list
distribute-list out
redistribute
To suppress networks from being advertised in updates, use the distribute-list out router configuration command. To cancel this function, use the no form of this command.
distribute-list access-list-number out [interface-name | routing-process]| access-list-number | Standard IPX access list number in the range 800 to 899. The list explicitly specifies which networks are to be sent and which are to be suppressed in routing updates. |
| out | Applies the access list to outgoing routing updates. |
| interface-name | (Optional) Interface on which the access list should be applied to outgoing updates. If no interface is specified, the access list is applied to all outgoing updates. |
| routing-process | (Optional) Name of a particular routing process (rip or eigrp autonomous-system-number). |
Disabled
Router configuration
When redistributing networks, a routing process name can be specified as an optional trailing argument to the distribute-list out command. This causes the access list to be applied to only those routes derived from the specified routing process. After the process-specific access list is applied, any access list specified by a distribute-list out command without a process name argument is applied. Addresses not specified in the distribute-list out command are not advertised in outgoing routing updates.
The following example causes only one network--network 3--to be advertised by an Enhanced IGRP routing process:
access-list 800 permit 3
access-list 800 deny -1
!
ipx router eigrp 100
network 3
distribute-list 800 out
access-list
distribute-list in
redistribute
To apply a generic output filter to an interface, use ipx access-group interface configuration command. To remove the access list, use the no form of this command.
ipx access-group access-list-number| access-list-number | Number of the access list. All outgoing packets defined with either standard or extended access lists and forwarded through the interface are filtered by the entries in this access list. For standard access lists, access-list-number is a decimal number from 800 to 899. For extended access lists, access-list-number is a decimal number from 900 to 999. |
No filters are predefined.
Interface configuration
Generic filters control which packets are sent out an interface based on the packet's source and destination addresses, IPX protocol type, and source and destination socket numbers. You use the standard access-list and extended access-list commands to specify the filtering conditions.
You can apply only one generic filter to an interface.
In the following example, access list 801 is applied to Ethernet interface 1:
interface ethernet 1
ipx access-group 801
A dagger (+) indicates that the command is documented in another chapter.
access-list (standard)
access-list (extended)
priority-list protocol +
To enable IPX accounting, use the ipx accounting interface configuration command. To disable IPX accounting, use the no form of this command.
ipx accountingThis command has no arguments or keywords.
Disabled
Interface configuration
IPX accounting allows you to collect information about IPX packets and the number of bytes that are switched through the router. You collect information based on the source and destination IPX address. Accounting tracks only IPX traffic that is passing out of the router; it does not track traffic generated by or terminating at the router.
IPX accounting statistics will be accurate even if IPX fast switching is enabled or if IPX access lists are being used. However, IPX accounting does not keep statistics if autonomous switching is enabled.
The router software maintains two accounting databases, an active database and a checkpointed database.
The following example enables IPX accounting on Ethernet interface 0:
interface ethernet 0
ipx accounting
clear ipx accounting
ipx accounting-list
ipx accounting-threshold
ipx accounting-transits
show ipx accounting
To filter the networks for which IPX accounting information is kept, use the ipx accounting-list global configuration command. To remove the filter, use the no form of this command.
ipx accounting-list number mask| number | Network number. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE.
You do not need to specify leading zeros in the network number. For example, for the network number 000000AA you can enter AA. |
| mask | Network mask. |
No filters are predefined.
Global configuration
The source and destination addresses of each IPX packet are logically ANDed with the mask and compared with the network number. If there is a match, accounting information about the IPX packet is entered into the accounting database. If there is no match, the IPX packet is considered to be a transit packet and may be counted, depending on the setting of the ipx accounting-transits global configuration command.
The following example adds all networks with IPX network numbers beginning with 1 to the list of networks for which accounting information is kept:
ipx accounting-list 1 0000.0000.0000
clear ipx accounting
ipx accounting
ipx accounting-threshold
ipx accounting-transits
show ipx accounting
To set the maximum number of accounting database entries, use the ipx accounting-threshold global configuration command. To restore the default, use the no form of this command.
ipx accounting-threshold threshold| threshold | Maximum number of entries (source and destination address pairs) that the router can accumulate. |
512 entries
Global configuration
The accounting threshold defines the maximum number of entries (source and destination address pairs) that the router accumulates. The threshold is designed to prevent IPX accounting from consuming all available free memory. This level of memory consumption could occur in a router that is switching traffic for many hosts. To determine whether overflows have occurred, used the show ipx accounting EXEC command.
The following example sets the IPX accounting database threshold to 500 entries:
ipx accounting-threshold 500
clear ipx accounting
ipx accounting
ipx accounting-list
ipx accounting-transits
show ipx accounting
To set the maximum number of transit entries that will be stored in the IPX accounting database, use the ipx accounting-transits global configuration command. To disable this function, use the no form of this command.
ipx accounting-transits count| count | Number of transit entries that will be stored in the IPX accounting database. |
0 entries
Global configuration
Transit entries are those that do not match any of the filters specified by ipx accounting-list global configuration commands. If you have not defined any filters, no transit entries are possible.
To maintain accurate accounting totals, the router software maintains two accounting databases: an active database and a checkpointed database.
The following example specifies a maximum of 100 transit records to be stored in the IPX accounting database:
ipx accounting-transits 100
clear ipx accounting
ipx accounting
ipx accounting-list
ipx accounting-threshold
show ipx accounting
To change the time between successive queries of each Enhanced IGRP neighbor's backup server table, use the ipx backup-server-query-interval global configuration command. To restore the default time, use the no form of this command.
ipx backup-server-query-interval interval| interval | Minimum time, in seconds, between successive queries of each Enhanced IGRP neighbor's backup server table. The default is 15 seconds. |
15 seconds
Global configuration
A lower interval may use more CPU resources, but may cause lost server information to be retrieved from other servers' tables sooner.
The following example changes the server query time to 5 seconds:
ipx backup-server-query-interval 5
To set the default interpacket delay for RIP updates sent on all interfaces, use the ipx default-output-rip-delay global configuration command. To return to the initial default delay value, use the no form of this command.
ipx default-output-rip-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet RIP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between routing update packets).
Global configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet routing update. The ipx default-output-rip-delay command sets a default interpacket delay for all interfaces.
The system uses the delay specified by the ipx default-output-rip-delay command for periodic and triggered routing updates when no delay is set for periodic and triggered routing updates on an interface. When you set a delay for triggered routing updates, the system uses the delay specified by the ipx default-output-rip-delay command for only the periodic routing updates sent on all interfaces.
To set a delay for triggered routing updates, see the ipx triggered-rip-delay or ipx default-triggered-rip-delay commands.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX machines. These machines may lose RIP updates because they process packets more slowly than the router sends them. The delay imposed by this command forces the router to pace its output to the slower-processing needs of these IPX machines.
The default delay on a NetWare 3.11 server is about 100 ms.
This command is also useful on limited bandwidth point-to-point links or X.25 and Frame Relay multipoint interfaces.
The following example sets a default interpacket delay of 55 ms for RIP updates sent on all interfaces:
ipx default-output-rip-delay 55
ipx default-triggered-rip-delay
ipx output-rip-delay
ipx triggered-rip-delay
To set a default interpacket delay for SAP updates sent on all interfaces, use the ipx default-output-sap-delay global configuration command. To return to the initial default delay value, use the no form of this command.
ipx default-output-sap-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet SAP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between update packets).
Global configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet SAP update. The ipx default-output-sap-delay command sets a default interpacket delay for all interfaces.
The system uses the delay specified by the ipx default-output-sap-delay command for periodic and triggered SAP updates when no delay is set for periodic and triggered updates on an interface. When you set a delay for triggered updates, the system uses the delay specified by the ipx default-output-sap-delay command only for the periodic SAP updates sent on all interfaces.
To set a delay for triggered updates, see the ipx triggered-sap-delay or ipx default-triggered-sap-delay commands.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX servers. These servers may lose SAP updates because they process packets more slowly than the router sends them. The delay imposed by this command forces the router to pace its output to the slower-processing needs of these servers.
The default delay on a NetWare 3.11 server is about 100 ms.
This command is also useful on limited bandwidth point-to-point links or X.25 interfaces.
The following example sets a default interpacket delay of 55 ms for SAP updates sent on all interfaces:
ipx default-output-sap-delay 55
ipx default-triggered-sap-delay
ipx output-sap-delay
ipx triggered-sap-delay
To set the default interpacket delay for triggered RIP updates sent on all interfaces, use the ipx default-triggered-rip-delay global configuration command. To return to the system default delay, use the no form of this command.
ipx default-triggered-rip-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet RIP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between routing update packets).
Global configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet routing update. A triggered routing update is one that the system sends in response to a "trigger" event, such as a request packet, interface up/down, route up/down, or server up/down.
The ipx default-triggered-rip-delay command sets the default interpacket delay for triggered routing updates sent on all interfaces. On a single interface, you can override this global default delay for triggered routing updates using the ipx triggered-rip-delay interface command.
The global default delay for triggered routing updates overrides the delay value set by the ipx output-rip-delay or ipx default-output-rip-delay command for triggered routing updates.
If the delay value set by the ipx output-rip-delay or ipx default-output-rip-delay command is high, then we strongly recommend a low delay value for triggered routing updates so that updates triggered by special events are sent in a more timely manner than periodic routing updates.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX machines. These machines may lose RIP updates because they process packets more slowly than the router sends them. The delay imposed by this command forces the router to pace its output to the slower-processing needs of these IPX machines.
The default delay on a NetWare 3.11 server is about 100 ms.
When you do not set the interpacket delay for triggered routing updates, the system uses the delay specified by the ipx output-rip-delay or ipx default-output-rip-delay command for both periodic and triggered routing updates.
When you use the no form of the ipx default-triggered-rip-delay command, the system uses the delay set by the ipx output-rip-delay or ipx default-output-rip-delay command for triggered RIP updates, if set. Otherwise, the system uses the initial default delay as described in the "Default" section.
This command is also useful on limited bandwidth point-to-point links or X.25 and Frame Relay multipoint interfaces.
The following example sets an interpacket delay of 55 ms for triggered routing updates sent on all interfaces:
ipx default-triggered-rip-delay 55
ipx default-output-rip-delay
ipx output-rip-delay
ipx triggered-rip-delay
To set the default interpacket delay for triggered SAP updates sent on all interfaces, use the ipx default-triggered-sap-delay global configuration command. To return to the system default delay, use the no form of this command.
ipx default-triggered-sap-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet SAP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between update packets).
Global configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet SAP update. A triggered SAP update is one that the system sends in response to a "trigger" event, such as a request packet, interface up/down, route up/down, or server up/down.
The ipx default-triggered-sap-delay command sets the default interpacket delay for triggered SAP updates sent on all interfaces. On a single interface, you can override this global default delay for triggered updates using the ipx triggered-sap-delay interface command.
The global default delay for triggered updates overrides the delay value set by the ipx output-sap-delay or ipx default-output-sap-delay command for triggered updates.
If the delay value set by the ipx output-sap-delay or ipx default-output-sap-delay command is high, then we strongly recommend a low delay value for triggered updates so that updates triggered by special events are sent in a more timely manner than periodic updates.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX servers. These servers may lose SAP updates because they process packets more slowly than the router sends them. The delay imposed by this command forces the router to pace its output to the slower-processing needs of these IPX servers.
The default delay on a NetWare 3.11 server is about 100 ms.
When you do not set the interpacket delay for triggered SAP updates, the system uses the delay specified by the ipx output-sap-delay or ipx default-output-sap-delay command for both periodic and triggered SAP updates.
When you use the no form of the ipx default-triggered-sap-delay command, the system uses the delay set by the ipx output-sap-delay or ipx default-output-sap-delay command for triggered SAP updates, if set. Otherwise, the system uses the initial default delay as described in the "Default" section.
This command is also useful on limited bandwidth point-to-point links or X.25 and Frame Relay multipoint interfaces.
The following example sets an interpacket delay of 55 ms for triggered SAP updates sent on all interfaces:
ipx default-triggered-sap-delay 55
ipx default-output-sap-delay
ipx output-sap-delay
ipx triggered-sap-delay
To set the tick count, use the ipx delay interface configuration command. To reset the default increment in the delay field, use the no form of this command.
ipx delay ticks| ticks | Number of IBM clock ticks of delay to use. One clock tick is 1/18 of a second (approximately 55 milliseconds). |
The default delay is determined from the delay configured on the interface with the delay command. It is (interface delay + 333) / 334. Therefore, unless you change the delay by a value greater than 334, you will not notice a difference.
Interface configuration
The ipx delay command sets the count used in the IPX RIP delay field, which is also known as the ticks field.
IPXWAN links determine their delay dynamically. Therefore, the ipx delay command has no effect.
Leaving the delay at its default value is sufficient for most interfaces.
The following example changes the delay for serial interface 0 to 10 ticks:
interface serial 0
ipx delay 10
A dagger (+) indicates that the command is documented in another chapter.
delay +
ipx maximum-paths
ipx output-network-filter
ipx output-rip-delay
To administratively shut down an IPX network, use the ipx down interface configuration command. To restart the network, use the no form of this command.
ipx down network| network | Number of the network to shut down. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. |
Disabled
Interface configuration
The ipx down command administratively shuts down the specified network. The network still exists in the configuration, but is not active. When shutting down, the network sends out update packets informing its neighbors that it is shutting down. This allows the neighboring systems to update their routing, SAP, and other tables without having to wait for routes and services learned via this network to time out.
The following example administratively shuts down network AA on Ethernet interface 0:
interface ethernet 0
ipx down AA
To change the delay when responding to Get Nearest Server (GNS) requests, use the ipx gns-response-delay global configuration command. To return to the default delay, use the no form of this command.
ipx gns-response-delay [milliseconds]| milliseconds | (Optional) Time, in milliseconds, that the router waits after receiving a Get Nearest Server request from an IPX client before responding with a server name to that client. The default time is 0 milliseconds. A value of zero indicates no delay. |
0 milliseconds
Global configuration
The delay in responding to Get Nearest Server requests is imposed so that in certain topologies any local Novell IPX servers respond to the GNS requests before our router does. It is desirable to have these end-host server systems get their reply to the client before the router does, because the client typically takes the first response, not the best, and in this case the best response is the one from the local server.
NetWare 2.x has a problem with dual-connected servers in parallel with a router. If you are using this version of NetWare, you should set a GNS delay. A value of 500 ms is recommended.
In situations in which servers are always located across routers from their clients, there is no need for a delay to be imposed.
The following example sets the delay in responding to GNS requests to 500 milliseconds (0.5 second):
ipx gns-response-delay 500
To rotate using a round-robin selection method through a set of eligible servers when responding to Get Nearest Server (GNS) requests, use the ipx gns-round-robin global configuration command. To use the most recently learned server, use the no form of this command.
ipx gns-round-robinThe command has no arguments or keywords.
The most recently learned, eligible server is used.
Global configuration
In the normal server selection process, requests for service are responded to with the most recently learned, closest server. If you enable the round-robin method, the router maintains a list of the nearest servers eligible to provide specific services. It uses this list when responding to Get Nearest Server (GNS) requests. Responses to requests are distributed in a round-robin fashion across all active IPX interfaces on the router.
Eligible servers are those that satisfy the "nearest" requirement for a given request and that are not filtered either by a SAP filter or by a GNS filter.
The following example responds to GNS requests using a round-robin selection method from a list of eligible nearest servers:
ipx gns-round-robin
ipx output-gns-filter
ipx output-sap-filter
To configure the interval between Enhanced IGRP hello packets, use the ipx hello-interval eigrp interface configuration command. To restore the default interval, use the no form of this command.
ipx hello-interval eigrp autonomous-system-number seconds| autonomous-system-number | Enhanced IGRP autonomous system number. It can be a decimal integer from 1 to 65535. |
| seconds | Interval between hello packets, in seconds. The default interval is 5 seconds, which is one-third of the default hold time. |
5 seconds
Interface configuration
If the current value for the hold time is less than two times the interval between hello packets, the hold time will be reset.
The following example changes the hello interval to 10 seconds:
interface ethernet 0
ipx network 10
ipx hello-interval eigrp 4 10
ipx hold-time eigrp
To forward broadcast packets (except type 20 propagation packets) to a specified server, use the ipx helper-address interface configuration command. To disable this function, use the no form of this command.
ipx helper-address network.node| network | Network on which the target IPX server resides. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of -1 indicates all-nets flooding. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA you can enter just AA. |
| node | Node number of the target Novell server. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). A node number of FFFF.FFFF.FFFF matches all servers. |
Disabled
Interface configuration
Routers normally block all broadcast requests and do not forward them to other network segments. This is done to prevent the degradation of performance over the entire network. The ipx helper-address command allows broadcasts to be forwarded to other networks (except type 20 propagation packets). This is useful when a network segment does not have an end-host capable of servicing a particular type of broadcast request. This command lets you forward the broadcasts to a server, network, or networks that can process them. Incoming unrecognized broadcast packets that match the access list created with the ipx helper-list command, if it is present, are forwarded.
Note that type 20 propagation packet handling is controlled by a separate mechanism. See the discussion of the ipx type-20-packet-propagation command for more information.
You can specify multiple ipx helper-address commands on a given interface.
Our routers support all-networks flooded broadcasts (sometimes referred to as all-nets flooding). These are broadcast messages that are forwarded to all networks. To configure the all-nets flooding, define the IPX helper address for an interface as follows:
ipx helper-address -1.FFFF.FFFF.FFFF
On systems configured for IPX routing, this helper address is displayed as follows (via the show ipx interface command):
FFFFFFFF.FFFF.FFFF.FFFF
Although our routers take care to keep broadcast traffic to a minimum, some duplication is unavoidable. When loops exist, all-nets flooding can propagate bursts of excess traffic that will eventually age out when the hop count reaches its limit (16 hops). Use all-nets flooding carefully and only when necessary. Note that you can apply additional restrictions by defining a helper list.
In the following example, all-nets broadcasts on Ethernet interface 0 (except type 20 propagation packets) are forwarded to IPX server 00b4.23cd.110a on network bb:
interface ethernet 0
ipx helper-address bb.00b4.23cd.110a
ipx helper-list
ipx type-20-propagation
To assign an access list to an interface to control broadcast traffic (including type 20 propagation packets), use the ipx helper-list interface configuration command. To remove the access list from an interface, use the no form of this command.
ipx helper-list access-list-number| access-list-number | Number of the access list. All outgoing packets defined with either standard or extended access lists are filtered by the entries in this access list. For standard access lists, access-list-number is a decimal number from 800 to 899. For extended access lists, it is a decimal number from 900 to 999. |
No access list is preassigned.
Interface configuration
The ipx helper-list command specifies an access list to use in forwarding broadcast packets. One use of this command is to prevent client nodes from discovering services they should not use.
Because the destination address of a broadcast packet is by definition the broadcast address, this command is useful only for filtering based on the source address of the broadcast packet.
The helper list, if present, is applied to both all-nets broadcast packets and type 20 propagation packets.
The helper list on the input interface is applied to packets before they are output via either the helper address or type 20 propagation packet mechanism.
You should filter IPX broadcasts on dial-on-demand routing (DDR) and other similar interfaces, because IPX sends broadcast messages very regularly.
The following example assigns access list 900 to Ethernet interface 0 to control broadcast traffic:
interface ethernet 0
ipx helper-list 900
access-list (standard)
access-list (extended)
ipx helper-address
ipx type-20-propagation
To specify the length of time a neighbor should consider Enhanced IGRP hello packets valid, use the ipx hold-time eigrp interface configuration command. To restore the default time, use the no form of this command.
ipx hold-time eigrp autonomous-system-number seconds| autonomous-system-number | Enhanced IGRP autonomous system number. It can be a decimal integer from 1 to 65535. |
| seconds | Hold time, in seconds. The hold time is advertised in hello packets and indicates to neighbors the length of time they should consider the sender valid. The default hold time is 15 seconds, which is three times the hello interval. |
15 seconds
Interface configuration
If the current value for the hold time is less than two times the interval between hello packets, the hold time will be reset to three times the hello interval.
If a router does not receive a hello packet within the specified hold time, routes through the router are considered available.
Increasing the hold time delays route convergence across the network.
The following example changes the hold time to 45 seconds:
interface ethernet 0
ipx network 10
ipx hold-time eigrp 4 45
ipx hello-interval eigrp
To control which networks are added to the router's routing table, use the ipx input-network-filter interface configuration command. To remove the filter from the interface, use the no form of this command.
ipx input-network-filter access-list-number| access-list-number | Number of the access list. All incoming packets defined with either standard or extended access lists are filtered by the entries in this access list. For standard access lists, access-list-number is a decimal number from 800 to 899. For extended access lists, it is a decimal number from 900 to 999. |
No filters are predefined.
Interface configuration
The ipx input-network-filter command controls which networks are added to the routing table based on the networks learned in incoming IPX routing updates (RIP updates) on the interface.
You can issue only one ipx input-network-filter command on each interface.
In the following example, access list 876 controls which networks are added to the routing table when IPX routing updates are received on Ethernet interface 1. Routing updates for network 1b will be accepted. Routing updates for all other networks are implicitly denied and are not added to the routing table.
access-list 876 permit 1b
interface ethernet 1
ipx input-network-filter 876
The following example is a variation of the preceding that explicitly denies network 1a and explicitly allows updates for all other networks:
access-list 876 deny 1a
access-list 876 permit -1
access-list (standard)
access-list (extended)
ipx output-network-filter
ipx router-filter
To control which services are added to the router's SAP table, use the ipx input-sap-filter interface configuration command. To remove the filter, use the no form of this command.
ipx input-sap-filter access-list-number| access-list-number | Number of the SAP access list. All incoming packets are filtered by the entries in this access list. The argument access-list-number is a decimal number from 1000 to 1099. |
No filters are predefined.
Interface configuration
The ipx input-sap-filter command filters all incoming service advertisements received by the router. This is done prior to a router's accepting information about a service.
You can issue only one ipx input-sap-filter command on each interface.
When configuring SAP filters for NetWare 3.11 and later servers, use the server's internal network and node number (the node number is always 0000.0000.0001) as its address in the SAP access-list command. Do not use the network.node address of the particular interface board.
The following example denies service advertisements about the server at address 3c.0800.89a1.1527, but accepts information about all other services on all other networks:
access-list 1000 deny 3c.0800.89a1.1527
access-list 1000 permit -1
interface ethernet 0
ipx input-sap-filter 1000
access-list (SAP filtering)
ipx output-sap-filter
ipx router-sap-filter
To configure the IPXWAN protocol on a serial interface, use the ipx ipxwan interface configuration command. To disable the IPXWAN protocol, use the no form of this command.
ipx ipxwan local-node number local-server [retry-interval] [retry-attempts]| local-node | Primary network number of the router. This is an IPX network number that is unique across the entire internet. On NetWare 3.x servers, the primary network number is called the internal network number. The router with the higher number is determined to be the link Master. |
| number | The IPX network number to be used for the link if this router is the one determined to be the link master. The number is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE.
You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can just enter AA. |
| local-server | Name of the local router. It can be up to 47 characters long, and can contain uppercase letters, digits, underscores (_), hyphens (-), and at signs (@). On NetWare 3.x servers, the local server is called the router name. |
| retry-interval | (Optional) Retry interval, in seconds. This interval defines how often the router will retry failed negotiation attempts. It can be a value from 1 through 600. The default is 20 seconds. |
| retry-attempts | (Optional) Maximum number of times the router will retry failed negotiation attempts. It can be a value from 1 through 100. The default is 3. The router intentionally ignores the IPXWAN retry counter and continues to send TIMER_REQUEST packets until it receives a TIMER_RESPONSE packet. |
IPXWAN is disabled.
When enabled, the command has the following defaults:
retry-interval: 20 seconds
retry-attempts: 3
Interface configuration
IPXWAN is a startup end-to-end options negotiations protocol. When a link comes up, the first IPX packets sent across are IPXWAN packets negotiating the options for the link. When the IPXWAN options have been successfully determined, normal IPX traffic starts. The three options negotiated are the link IPX network number, Ethernet network number, and link delay (ticks) characteristics.The side of the link with the higher local-node number (internal network number) gives the IPX network number and delay to use for the link to the other side. Once IPXWAN finishes, no IPXWAN packets are sent unless link characteristics change or the connection fails. For example, if the IPX delay is changed from the default setting, an IPXWAN restart will be forced.
To enable the IPXWAN protocol on a serial interface, you must not have configured an IPX network number (using the ipx network interface configuration command) on that interface.
If you want to control the delay on a link, use the ipx delay interface configuration command. If you issue this command when the serial link is already up, the state of the link will be reset and renegotiated.
The following example enables IPXWAN on serial interface 1 on the local router CHICAGO-RTR. When the link comes up, CHICAGO-RTR will be the master because it has a larger internal network number. It will give the IPX number 100 to NYC-RTR to use as the network number for the link. The link delay, in ticks, will be determined by the exchange of packets between the two routers.
On the local router (CHICAGO-RTR):
interface serial 1
no ipx network
encapsulation ppp
ipx ipxwan 6666 100 CHICAGO-RTR
On the remote router (NYC-RTR):
interface serial 0
no ipx network
encapsulation ppp
ipx ipxwan 1000 101 NYC-RTR
A dagger (+) indicates that the command is documented in another chapter.
encapsulation ppp +
ipx delay
ipx network
show ipx interfaces
To set the maximum number of equal-cost paths the router uses when forwarding packets, use the ipx maximum-paths global configuration command. To restore the default value, use the no form of this command.
ipx maximum-paths paths| paths | Maximum number of equal-cost paths which the router will use. It can be an integer from 1 to 512. The default value is 1. |
1 path
Global configuration
The ipx maximum-paths command is designed to increase throughput by allowing the router to choose among several equal-cost, parallel paths. (Note that when paths have differing costs, the router chooses lower-cost routes in preference to higher-cost routes.) IPX does load sharing on a packet-by-packet basis in round-robin fashion, regardless of whether you are using fast switching or process switching. That is, the first packet is sent along the first path, the second packet along the second path, and so on. When the final path is reached, the next packet is sent to the first path, the next to the second path, and so on.
Limiting the number of equal-cost paths can save memory on routers with limited memory or very large configurations. Additionally, in networks with a large number of multiple paths and systems with limited ability to cache out-of-sequence packets, performance might suffer when traffic is split between many paths.
In the following example, the router uses up to three parallel paths:
ipx maximum-paths 3
ipx delay
show ipx route
To control incoming IPX NetBIOS messages, use the ipx netbios input-access-filter interface configuration command. To remove the filter, use the no form of this command.
ipx netbios input-access-filter {host | bytes} name| host | Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list host commands. |
| bytes | Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list bytes commands. |
| name | Name of a NetBIOS access list. |
No filters are predefined.
Interface configuration
You can issue only one ipx netbios input-access-filter host and one ipx netbios input-access-filter bytes command on each interface.
These filters apply only to IPX NetBIOS packets. They have no effect on LLC2 NetBIOS packets.
The following example filters packets arriving on Token Ring interface 1 using the NetBIOS access list "engineering":
netbios access-list host engineering permit eng*
netbios access-list host engineering deny manu*
interface token 1
ipx netbios input-access-filter engineering
ipx netbios output-access filter
netbios access-list
show ipx interface
To control outgoing NetBIOS messages, use the ipx netbios output-access-filter interface configuration command. To remove the filter, use the no form of this command.
ipx netbios output-access-filter {host | bytes} name| host | Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list host commands. |
| bytes | Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list bytes commands. |
| name | Name of a previously defined NetBIOS access list. |
No filters are predefined.
Interface configuration
You can issue only one ipx netbios output-access-filter host and one ipx netbios output-access-filter bytes command on each interface.
These filters apply only to IPX NetBIOS packets. They have no effect on LLC2 NetBIOS packets.
The following example filters packets leaving Token Ring interface 1 using the NetBIOS access list "engineering":
netbios access-list bytes engineering permit 20 AA**04
interface token 1
ipx netbios output-access-filter bytes engineering
ipx netbios input-access filter
netbios access-list
show ipx interface
To enable IPX routing on a particular interface and to optionally select the type of encapsulation (framing), use the ipx network interface configuration command. To disable IPX routing, use the no form of this command.
ipx network network [encapsulation encapsulation-type [secondary]]IPX routing is disabled.
Encapsulation types:
For Ethernet: novell-ether
For Token Ring: sap
For FDDI: snap
Interface configuration
The extended ipx network command allows you to configure more than one logical network on the same physical network (network cable segment). Each network on a given interface must have a different encapsulation type. The first network you configure on an interface is considered to be the primary network. Any additional networks are considered to be secondary networks; these must include the secondary keyword. You also can use this command to configure a single logical network on a physical network.
You can configure an IPX network on any supported interface as long as all the networks on the same physical interface use a distinct encapsulation type. For example, you can configure up to four IPX networks on a single Ethernet cable because Ethernet supports four encapsulation types.
The interface processes only packets with the correct encapsulation and the correct network number. IPX networks using other encapsulations can be present on the physical network. The only effect on the router is that it uses some processing time to examine packets to determine whether they have the correct encapsulation.
If you use the standard ipx network and ipx encapsulation commands on an interface that supports more than one logical network, you can use them only to define the first, or primary, network on the interface. Use the extended ipx network command to define additional logical networks.
All logical networks on an interface share the same set of configuration parameters. For example, if you change the IPX RIP update time on an interface, you change it for all networks on that interface.
This command is useful when migrating from one type of encapsulation to another. If you are using it for this purpose, you should define the new encapsulation on the primary network.
To delete all networks on an interface, use the following command:
no ipx networkDeleting the primary network with the following command also deletes all networks on that interface. The argument number is the number of the primary network.
no ipx network numberTo delete a secondary network on an interface, use one of the following commands. The argument number is the number of a secondary network.
no ipx network numberThe following two commands also allow you to enable IPX routing on an interface and specify the encapsulation. These commands can be used on interfaces that support a single network or when enabling the primary subinterface on an interface that supports multiple networks. They are supported in this release of the software to provide compatibility with older versions of the router software.
ipx networkThe following example configures an interface that has four logical networks:
interface ethernet 0
ipx network 0123
ipx encapsulation snap
ipx network 0234 encapsulation sap secondary
ipx network 0345 encapsulation sap secondary
ipx network 0456 encapsulation sap secondary
ipx routing
To control which servers are included in the Get Nearest Server (GNS) responses sent by the router, use the ipx output-gns-filter interface configuration command. To remove the filter from the interface, use the no form of this command.
ipx output-gns-filter access-list-number| access-list-number | Number of the SAP access list. All outgoing GNS packets are filtered by the entries in this access list. The argument access-list-number is a decimal number from 1000 to 1099. |
No filters are predefined.
Interface configuration
You can issue only one ipx output-gns-filter command on each interface.
The following example excludes the server at address 3c.0800.89a1.1527 from GNS responses sent on Ethernet interface 0, but allows all other servers:
access-list 1000 deny 3c.0800.89a1.1527
access-list 1000 permit -1
ipx routing
interface ethernet 0
ipx output-gns-filter 1000
access-list (SAP filtering)
ipx gns-round-robin
To control the list of networks included in routing updates sent out an interface, use the ipx output-network-filter interface configuration command. To remove the filter from the interface, use the no form of this command.
ipx output-network-filter access-list-number| access-list-number | Number of the access list. All outgoing packets defined with either standard or extended access lists are filtered by the entries in this access list. For standard access lists, access-list-number is a decimal number from 800 to 899. For extended access lists, it is a decimal number from 900 to 999. |
No filters are predefined.
Interface configuration
The ipx output-network-filter command controls which networks the router advertises in its IPX routing updates (RIP updates).
You can issue only one ipx output-network-filter command on each interface.
In the following example, access list 896 controls which networks are specified in routing updates sent out the serial 1 interface. This configuration causes network 2b to be the only network advertised in Novell routing updates sent on the specified serial interface.
access-list 896 permit 2b
interface serial 1
ipx output-network-filter 896
access-list (standard)
access-list (extended)
ipx input-network-filter
ipx router-filter
To set the interpacket delay for RIP updates sent on a single interface, use the ipx output-rip-delay interface configuration command. To return to the default value, use the no form of this command.
ipx output-rip-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet RIP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between routing update packets).
Interface configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet routing update. The ipx output-rip-delay command sets the interpacket delay for a single interface.
The system uses the interpacket delay specified by the ipx output-rip-delay command for periodic and triggered routing updates when no delay is set for triggered routing updates. When you set a delay for triggered routing updates, the system uses the delay specified by the ipx output-rip-delay command for only the periodic routing updates sent on the interface.
To set a delay for triggered routing updates, see the ipx triggered-rip-delay or ipx default-triggered-rip-delay commands.
You can also set a default RIP interpacket delay for all interfaces. See the ipx default-output-rip-delay command for more information.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX machines. These machines may lose RIP updates because they process packets more slowly than the router sends them. The delay imposed by this command forces the router to pace its output to the slower-processing needs of these IPX machines.
The default delay on a NetWare 3.11 server is about 100 ms.
This command is also useful on limited bandwidth point-to-point links or X.25 and Frame Relay multipoint interfaces.
The following example establishes a 55-ms interpacket delay on serial interface 0:
interface serial 0
ipx network 106A
ipx output-rip-delay 55
ipx update-time
ipx default-output-rip-delay
ipx default-triggered-rip-delay
ipx triggered-rip-delay
To set the interpacket delay for SAP updates sent on a single interface, use the ipx output-sap-delay interface configuration command. To return to the default delay value, use the no form of this command.
ipx output-sap-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet SAP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between update packets).
Interface configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet SAP update. The ipx output-sap-delay command sets the interpacket delay for a single interface.
The system uses the interpacket delay specified by the ipx output-sap-delay command for periodic and triggered SAP updates when no delay is set for triggered updates. When you set a delay for triggered updates, the system uses the delay specified by the ipx output-sap-delay command only for the periodic updates sent on the interface.
To set a delay for triggered updates, see the ipx triggered-sap-delay or ipx default-triggered-sap-delay commands.
You can also set a default SAP interpacket delay for all interfaces. See the ipx default-output-sap-delay command for more information.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX servers. These servers may lose SAP updates because they process packets more slowly than the router sends them. The delay imposed by the ipx output-sap-delay command forces the router to pace its output to the slower-processing needs of these servers.
The default delay on a NetWare 3.11 server is about 100 ms.
This command is also useful on limited bandwidth point-to-point links or X.25 and Frame Relay multipoint interfaces.
The following example establishes a 55-ms delay between packets in multiple-packet SAP updates on Ethernet interface 0:
interface ethernet 0
ipx network 106A
ipx output-sap-delay 55
ipx default-output-sap-delay
ipx default-triggered-sap-delay
ipx sap-interval
ipx triggered-sap-delay
To control which services are included in Service Advertisement Protocol (SAP) updates sent by the router, use the ipx output-network-filter interface configuration command. To remove the filter, use the no form of this command.
ipx output-sap-filter access-list-number| access-list-number | Number of the SAP access list. All outgoing service advertisements are filtered by the entries in this access list. The argument access-list-number is a decimal number from 1000 to 1099. |
No filters are predefined.
Interface configuration
The router applies output SAP filters prior to sending SAP packets.
You can issue only one ipx output-sap-filter command on each interface.
When configuring SAP filters for NetWare 3.11 and later servers, use the server's internal network and node number (the node number is always 0000.0000.0001) as its address in the SAP access-list command. Do not use the network.node address of the particular interface board.
The following example denies service advertisements about server 0000.0000.0001 on network aa from being send on network 4d (via Ethernet interface 1). All other services are advertised via this network. All services, included those from server aa.0000.0000.0001, are advertised via networks 3c and 2b.
access-list 1000 deny aa.0000.0000.0001
access-list 1000 permit -1
interface ethernet 0
ipx net 3c
interface ethernet 1
ipx network 4d
ipx output-sap-filter 1000
interface serial 0
ipx network 2b
access list (SAP filtering)
ipx gns-round-robin
ipx input-sap-filter
ipx router-sap-filter
To control whether odd-length packets are padded so as to be sent as even-length packets on an interface, use the ipx pad-process-switched-packets interface configuration command. To disable padding, use the no form of this command.
ipx pad-process-switched-packetsThis command has no arguments or keywords.
Enabled on Ethernet interfaces
Disabled on Token Ring, FDDI, and serial interfaces.
Interface configuration
Use this command only under the guidance of a customer engineer or other service representative.
The ipx pad-process-switched-packets command affects process-switched packets only, so you must disable fast switching before the ipx pad-process-switched-packets command has any effect.
Some IPX end hosts reject Ethernet packets that are not padded. Certain topologies can result in such packets being forwarded onto a remote Ethernet network. Under specific conditions, padding on intermediate media can be used as a temporary workaround for this problem.
ipx route-cache
To add a static route to the routing table, use the ipx route global configuration command. To remove a route from the routing table, use the no form of this command.
ipx route network network.node| network | Network to which you want to establish a static route.
This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. |
| network.node | Router to which to forward packets destined for the specified network.
The argument network is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter just AA. The argument node is the node number of the target router. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). |
No static routes are predefined.
Global configuration
The ipx route command forwards packets destined for the specified network (network) via the specified router (network.node), regardless of whether that router is sending dynamic routing information.
Be careful when assigning static routes. When links associated with static routes are lost, traffic may stop being forwarded, even though alternative paths might be available.
In the following example, the router at address 3abc.0000.0c00.1ac9 handles all traffic destined for network 5e:
ipx routing
ipx route 5e 3abc.0000.0c00.1ac9
show ipx route
To enable IPX fast switching and autonomous switching, use the ipx route-cache interface configuration command. To disable fast switching, use the no form of this command.
ipx route-cache [cbus | sse]| cbus | (Optional) Enables IPX autonomous switching |
| sse | (Optional) Enables SSE fast switching |
Fast switching enabled
Autonomous switching disabled
SSE switching disabled
Interface configuration
Specifying the ipx route-cache command with no keywords enables fast switching.
Fast switching allows higher throughput by switching packets using a cache created by previous transit packets. On ciscoBus-2 interface cards, fast switching is done between all encapsulation types. On other interface cards, fast switching is done in all cases except the following: transfer of packets with sap encapsulation from an Ethernet, a Token Ring, or an FDDI network to a standard serial line.
You might want to disable fast switching in two situations. One is if you want to save memory on the interface cards: fast-switching caches require more memory than those used for standard switching. The second situation is to avoid congestion on interface cards when a high-bandwidth interface is writing large amounts of information to a low-bandwidth interface.
Autonomous switching provides faster packet switching by allowing the ciscoBus processor to switch packets independently without having to interrupt the system processor. It is available only in Cisco 7000 systems, and in AGS+ systems with high-speed network controller CBus2-only interfaces, such as the CCTL2 ciscoBus controller running microcode version 11.0 or later.
SSE fast switching uses the silicon switching engine (SSE) on the Cisco 7000 Series SSP card to perform packet switching.
The following example enables fast switching and autonomous switching on an interface:
interface ethernet 0
ipx route-cache cbus
The following example enables fast switching and SSE fast switching on an interface:
interface ethernet 0/1
ipx route-cache sse
In the following example, both fast switching and autonomous switching are turned off on an interface:
interface ethernet 0
no ipx route-cache
Assuming that Ethernet 0 has ipx route-cache and ipx route-cache cbus is enabled, the following example turns off only autonomous switching on an interface, but leaves fast switching enabled:
interface ethernet 0
no ipx route-cache cbus
clear ipx cache
ipx source-network-update
ipx watchdog-spoof
show ipx cache
To specify the routing protocol to use, use the ipx router global configuration command.
ipx router {eigrp autonomous-system-number | rip}| eigrp autonomous-system-number | Specifies the Enhanced IGRP routing protocol. The argument autonomous-system-number is the Enhanced IGRP autonomous system number. It can be a decimal integer from 1 to 65535. |
| rip | Specifies the RIP routing protocol. It is on by default. |
RIP is enabled.
Global configuration
You must explicitly disable RIP if you do not want to use this routing protocol.
You can configure multiple Enhanced IGRP processes on a router. To do so, assign each a different autonomous system number.
The following example enables Enhanced IGRP on the router:
ipx router eigrp 4
network
redistribute
To control the routers from which packets are accepted, use the ipx router-filter interface configuration command. To remove the filter from the interface, use the no form of this command.
ipx router-filter access-list-number| access-list-number | Number of the access list. All incoming packets defined with either standard or extended access lists are filtered by the entries in this access list. For standard access lists, access-list-number is a decimal number from 800 to 899. For extended access lists, it is a decimal number from 900 to 999. |
No filters are predefined.
Interface configuration
You can issue only one ipx router-filter command on each interface.
In the following example, access list 866 controls the routers from which packets are accepted. For Ethernet interface 0, only packets from the router at 3c.0000.00c0.047d are accepted. All other packets are implicitly denied.
access-list 866 permit 3c.0000.00c0.047d
interface ethernet 0
ipx router-filter 866
access-list (standard)
access-list (extended)
ipx input-network-filter
ipx output-network-filter
To filter Service Advertisement Point (SAP) messages received from a particular router, use the ipx router-sap-filter interface configuration command. To remove the filter, use the no form of this command.
ipx router-sap-filter access-list-number| access-list-number | Number of the access list. All incoming service advertisements are filtered by the entries in this access list. The argument access-list-number is a decimal number from 1000 to 1099. |
No filters are predefined.
Interface configuration
You can issue only one ipx router-sap-filter command on each interface.
In the following example, the router will receive service advertisements only from router aa.0207.0104.0874:
access-list 1000 permit aa.0207.0104.0874
access-list 1000 deny -1
interface ethernet 0
ipx router-sap-filter 1000
access-list (SAP filtering)
ipx input-sap-filter
ipx output-sap-filter
ipx sap
show ipx interface
To enable IPX routing, use the ipx routing global configuration command. To disable IPX routing, use the no form of this command.
ipx routing [node]| node | (Optional) Node number of the router. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). It must not be a multicast address.
If you omit node, the router uses the hardware MAC address currently assigned to it as its node address. This is the MAC address of the first Ethernet, Token Ring, or FDDI interface card. If no satisfactory interfaces are present in the router (such as only serial interfaces), you must specify node. |
Disabled
Global configuration
The ipx routing command enables the IPX Routing Information Protocol (RIP) and Service Advertisement Point (SAP) services on the router.
If you omit the argument node and if the MAC address later changes, the IPX node address automatically changes to the new address. However, connectivity may be lost between the time that the MAC address changes and the time that the IPX clients and servers learn the router's new address.
If you plan to use DECnet and IPX routing concurrently on the same interface, you should enable DECnet router first, then enable IPX routing without specifying the optional MAC node number. If you enable IPX before enabling DECnet routing, routing for IPX will be disrupted.
The following example enables IPX routing:
ipx routing
ipx network
To specify static Service Advertisement Protocol (SAP) entries, use the ipx sap global configuration command. To remove static SAP entries, use the no form of this command.
ipx sap service-type name network.node socket hop-count| service-type | SAP service-type number. Table 19-3 earlier in this chapter lists some IPX SAP services. |
| name | Name of the server that provides the service. |
| network.node | Network number and node address of the server.
The argument network is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA you can enter just AA. The argument node is the node number of the target Novell server. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). |
| socket | Socket number for this service. Table 19-2 earlier in this chapter lists some IPX socket numbers. |
| hop-count | Number of hops to the server. |
Disabled
Global configuration
The ipx sap command allows you to add static entries into the SAP table. Each entry has a SAP service associated with it. Static SAP assignments always override any identical entries in the SAP table that are learned dynamically, regardless of hop count. The router will not announce a static SAP entry unless it has a route to that network.
In the following example, the route to JOES_SERVER is not yet learned, so the system displays an informational message. The JOES_SERVER service will not be announced in the regular SAP updates until the router learns the route to it either by means of a RIP update from a neighbor or an ipx sap command.
ipx sap 107 MAILSERV 160.0000.0c01.2b72 8104 1
ipx sap 4 FILESERV 165.0000.0c01.3d1b 451 1
ipx sap 143 JOES_SERVER A1.0000.0c01.1234 8170 2
no route to A1, JOES_SERVER won't be announced until route is learned
ipx input-sap-filter
ipx output-sap-filter
ipx router-sap-filter
show ipx servers
To send SAP updates only when a change occurs in the SAP table, use the ipx sap-incremental interface configuration command. To send periodic SAP updates, use the no form of this command.
ipx sap-incremental eigrp autonomous-system-number [rsup-only]| eigrp autonomous-system-number | IPX Enhanced IGRP autonomous system number. It can be a decimal integer from 1 to 65535. |
| rsup-only | (Optional) Indicates that the system uses Enhanced IGRP on this interface to carry reliable SAP update information only. RIP routing updates are used, and Enhanced IGRP routing updates are ignored. |
Enabled on serial interfaces
Disabled on LAN media (Ethernet, Token Ring, FDDI)
Interface configuration
With this functionality enabled, if an IPX Enhanced IGRP peer is found on the interface, SAP updates will be sent only when a change occurs in the SAP table. Periodic SAP updates are not sent. When no IPX Enhanced IGRP peer is present on the interface, periodic SAPs are always sent regardless of how this command is set.
If you configure the local router to send incremental SAP updates on an Ethernet, and if the local router has at least one IPX Enhanced IGRP neighbor and any servers, clients, or routers that do not have IPX Enhanced IGRP configured on the Ethernet interface, these devices will not receive complete SAP information from the local router.
If the incremental sending of SAP updates on an interface is configured and no IPX Enhanced IGRP peer is found, SAP updates will be sent periodically until a peer is found. Then, updates will be sent only when changes occur in the SAP table.
To reduce SAP traffic by sending partial SAP updates, specify the rsup-only keyword. SAP updates are then sent only when changes occur, and only changes are sent. This feature works with existing IPX RIP networks and IPX Enhanced IGRP networks.
The following example sends SAP updates on Ethernet interface 0 only when there is a change in the SAP table:
interface ethernet 0
ipx sap-incremental eigrp 200
To configure less frequent Service Advertisement Point (SAP) updates over slow links, use the ipx sap-interval interface configuration command. To return to the default value, use the no form of this command.
ipx sap-interval interval| interval | Interval, in minutes, between SAP updates sent by the router. The default value is 1 minute. If interval is 0, periodic updates are never sent. |
1 minute
Interface configuration
Setting the interval at which SAP updates are sent is most useful on limited-bandwidth, point-to-point links or on X.25 interfaces.
You should ensure that all IPX servers and routers on a given network have the same SAP interval. Otherwise, they may decide that a server is down when it is really up.
It is not possible to change the interval at which SAP updates are sent on most PC-based servers. This means that you should never change the interval for an Ethernet or Token Ring network that has servers on it.
Setting the interval to zero means that periodic SAP updates are never sent. It is recommended that you never do this. If you set the interval to zero, routers that are inaccessible for any reason when a server powers up or shuts down will miss that event, and will either fail to learn about new servers or fail to detect that the server shut down.
In the following example, SAP updates are sent (and expected) on serial interface 0 every 5 minutes:
interface serial 0
ipx sap-interval 5
ipx output-sap-delay
To configure the maximum length of the queue of pending input SAP GNS requests and SAP query packets, use the ipx sap-queue-maximum global configuration command. To return to the default value, use the no form of this command.
ipx sap-queue-maximum number| number | Maximum length of the queue of pending SAP requests. By default, there is no limit to the number of pending SAP requests that the router stores in this queue. |
No maximum queue size
Global configuration
The router maintains a list of SAP requests to process, including all pending Get Nearest Server (GNS) queries from clients attempting to reach servers. When the network is restarted, the router can be inundated with hundreds of requests for servers. Most of these can be repeated requests from the same clients. The ipx sap-queue-maximum command allows you to configure the maximum length allowed for the pending SAP requests queue. Packets received when the queue is full are dropped.
The following example sets the length of the queue of pending SAP requests to 20:
ipx sap-queue-maximum 20
To repair corrupted network numbers, use the ipx source-network-update interface configuration command. To disable this feature, use the no form of this command.
ipx source-network-updateThis command has no arguments or keywords.
Disabled
Interface configuration
In some early implementations of IPX client software, it was possible for the client's network number to become corrupted. The ipx source-network-update command repairs this number by setting the source network field of any packet on the local network that has a hop count of zero.
You must disable fast switching with the no ipx route-cache command before using the ipx source-network-update command.
This command interferes with the proper working of OS/2 Requestors. Therefore, do not use this command in a network that has OS/2 Requestors.
Do not use the ipx source-network-update command on interfaces on which NetWare servers are using internal network numbers.
 | Caution The ipx source-network-update command interferes with the proper working of OS/2 Requestors. Do not use this command in a network that has OS/2 Requestors. |
| Caution Do not use the ipx source-network-update command on interfaces on which NetWare (NetWare 3.1x or 4.0 or later) Servers are using internal network numbers. |
In the following example, corrupted network numbers on serial interface 0 are repaired:
interface serial 0
no ipx route-cache
ipx source-network-update
ipx route-cache
To configure split horizon, use the ipx split-horizon eigrp interface configuration command. To disable split horizon, use the no form of this command.
ipx split-horizon eigrp autonomous-system-number| autonomous-system-number | Enhanced IGRP autonomous system number. It can be a decimal integer from 1 to 65535. |
Enabled
Interface configuration
When split horizon is enabled, Enhanced IGRP update and query packets are not sent for destinations that have next hops on this interface. This reduces the number of Enhanced IGRP packets on the network.
Split horizon blocks information about routes from being advertised by a router out any interface from which that information originated. This behavior usually optimizes communication among multiple routers, particularly when links are broken. However, with nonbroadcast networks, such as Frame Relay and SMDS, situations can arise for which this behavior is less than ideal. For these situations, you may wish to disable split horizon.
The following example disables split horizon on serial interface 0:
interface serial 0
no ipx split-horizon eigrp 200
To set the interpacket delay for triggered RIP updates sent on a single interface, use the ipx triggered-rip-delay interface configuration command. To return to the default delay, use the no form of this command.
ipx triggered-rip-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet RIP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between routing update packets).
Interface configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet routing update. A triggered routing update is one that the system sends in response to a "trigger" event, such as a request packet, interface up/down, route up/down, or server up/down.
The ipx triggered-rip-delay command sets the interpacket delay for triggered routing updates sent on a single interface. The delay value set by this command overrides the delay value set by the ipx output-rip-delay or ipx default-output-rip-delay command for triggered routing updates sent on the interface.
If the delay value set by the ipx output-rip-delay or ipx default-output-rip-delay command is high, then we strongly recommend a low delay value for triggered routing updates so that updates triggered by special events are sent in a more timely manner than periodic routing updates.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX machines. These machines may lose RIP updates because they process packets more slowly than the router sends them. The delay imposed by this command forces the router to pace its output to the slower-processing needs of these IPX machines.
The default delay on a NetWare 3.11 server is about 100 ms.
When you do not set the interpacket delay for triggered routing updates, the system uses the delay specified by the ipx output-rip-delay or ipx default-output-rip-delay command for both periodic and triggered routing updates.
When you use the no form of the ipx triggered-rip-delay command, the system uses the global default delay set by the ipx default-triggered-rip-delay command for triggered RIP updates, if it is set. If it is not set, the system uses the delay set by the ipx output-rip-delay or ipx default-output-rip-delay command for triggered RIP updates, if set. Otherwise, the system uses the initial default delay as described in the "Default" section.
This command is also useful on limited bandwidth point-to-point links or X.25 and Frame Relay multipoint interfaces.
The following example sets an interpacket delay of 55 ms for triggered routing updates sent on interface FDDI 0:
int FDDI 0
ipx triggered-rip-delay 55
ipx default-output-rip-delay
ipx default-triggered-rip-delay
ipx output-rip-delay
To set the interpacket delay for triggered SAP updates sent on a single interface, use the ipx triggered-sap-delay interface configuration command. To return to the default delay, use the no form of this command.
ipx triggered-sap-delay delay| delay | Delay, in milliseconds, between packets in a multiple-packet SAP update. With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms. Novell recommends a delay of 55 ms. |
With Cisco IOS Release 10.0 and Release 10.2, the default delay is 0 ms (that is, no additional delay between update packets).
Interface configuration
The interpacket delay is the delay between the individual packets sent in a multiple-packet SAP update. A triggered SAP update is one that the system sends in response to a "trigger" event, such as a request packet, interface up/down, route up/down, or server up/down.
The ipx triggered-sap-delay command sets the interpacket delay for triggered updates sent on a single interface. The delay value set by this command overrides the delay value set by the ipx output-sap-delay or ipx default-output-sap-delay command for triggered updates sent on the interface.
If the delay value set by the ipx output-sap-delay or ipx default-output-sap-delay command is high, then we strongly recommend a low delay value for triggered updates so that updates triggered by special events are sent in a more timely manner than periodic updates.
Novell recommends a delay of 55 ms for compatibility with older and slower IPX servers. These servers may lose SAP updates because they process packets more slowly than the router sends them. The delay imposed by this command forces the router to pace its output to the slower-processing needs of these IPX servers.
The default delay on a NetWare 3.11 server is about 100 ms.
When you do not set the interpacket delay for triggered updates, the system uses the delay specified by the ipx output-sap-delay or ipx default-output-sap-delay command for both periodic and triggered SAP updates.
When you use the no form of the ipx triggered-sap-delay command, the system uses the global default delay set by the ipx default-triggered-sap-delay command for triggered SAP updates, if it is set. If it is not set, the system uses the delay set by the ipx output-sap-delay or ipx default-output-sap-delay command for triggered SAP updates, if set. Otherwise, the system uses the initial default delay as described in the "Default" section.
This command is also useful on limited bandwidth point-to-point links or X.25 and Frame Relay multipoint interfaces.
The following example sets an interpacket delay of 55 ms for triggered SAP updates sent on interface FDDI 0:
int FDDI 0
ipx triggered-sap-delay 55
ipx default-output-sap-delay
ipx default-triggered-sap-delay
ipx output-sap-delay
To forward IPX type 20 propagation packet broadcasts to specific network segments, use the ipx type-20-helpered interface configuration command. To disable this function, use the no form of this command.
ipx type-20-helperedThis command has no arguments or keywords.
Disabled
Interface configuration
The ipx type-20-helpered command disables the input and output of type 20 propagation packets as done by the ipx type-20-propagation interface configuration command.
The ipx type-20-propagation command broadcasts type 20 packets to all nodes on the network and imposes a hop-count limit of eight routers for broadcasting these packets. These functions are in compliance with the Novell IPX router specification. In contrast, the ipx type-20-helpered command broadcasts type 20 packets to only those nodes indicated by the ipx helper-address interface configuration command and extends the hop-count limit to 16 routers.
Use of the ipx type-20-helpered command does not comply with the Novell IPX router specification.
The following example forwards IPX type 20 propagation packet broadcasts to specific network segments:
interface ethernet 0
ipx network aa
ipx type-20-helpered
ipx helper-address bb.ffff.ffff.ffff
ipx helper-address
ipx type-20-propagation
To restrict the acceptance of IPX type 20 propagation packet broadcasts, use the ipx type-20-input-checks global configuration command. To remove these restrictions, use the no form of this command.
ipx type-20-input-checksThis command has no arguments or keywords.
Disabled
Global configuration
By default, the router is configured to block type 20 propagation packets. When type 20 packet handling is enabled on multiple interfaces, you can use the ipx type-20-input-checks command to impose additional restrictions on the acceptance of type 20 packets. Specifically, the router will accept type 20 propagation packets only on the single network that is the primary route back to the source network. Similar packets received via other networks will be dropped. This behavior can be advantageous in redundant topologies, because it reduces unnecessary duplication of type 20 packets.
The following example imposes additional restrictions on incoming type 20 broadcasts:
ipx type-20-input-checks
ipx type-20-output-checks
ipx type-20-propagation
To restrict the forwarding of IPX type 20 propagation packet broadcasts, use the ipx type-20-output-checks global configuration command. To remove these restrictions, use the no form of this command.
ipx type-20-output-checksThis command has no arguments or keywords.
Disabled
Global configuration
By default, the router is configured to block type 20 propagation packets. When type 20 packet handling is enabled on multiple interfaces, you can use the ipx type-20-output-checks command to impose additional restrictions on outgoing type 20 packets. Specifically, the router will forward these packets only to networks that are not routes back to the source network. (The router uses the current routing table to determine routes.) This behavior can be advantageous in redundant topologies, because it reduces unnecessary duplication of type 20 packets.
The following example imposes restrictions on outgoing type 20 broadcasts:
ipx type-20-output-checks
ipx type-20-input-checks
ipx type-20-propagation
To forward IPX type 20 propagation packet broadcasts to other network segments, use the ipx type-20-propagation interface configuration command. To disable both the reception and forwarding of type 20 broadcasts on an interface, use the no form of this command.
ipx type-20-propagationThis command has no arguments or keywords.
Disabled
Interface configuration
Routers normally block all broadcast requests. To allow input and output of type 20 propagation packets on an interface, use the ipx type-20-propagation command. Note that type 20 packets are subject to loop detection and control as specified in the IPX router specification.
Additional input and output checks may be imposed by the ipx type-20-input-checks and ipx type-20-output-checks commands.
IPX type 20 propagation packet broadcasts are subject to any filtering defined by the ipx helper-list command.
The following example enables both the reception and forwarding of type 20 broadcasts on Ethernet interface 0:
interface ethernet 0
ipx type-20-propagation
The following example enables the reception and forwarding of type 20 broadcasts between networks 123 and 456, but does not enable reception and forwarding of these broadcasts to and from network 789.
interface ethernet 0
ipx network 123
ipx type-20-propagation
!
interface ethernet 1
ipx network 456
ipx type-20-propagation
!
interface ethernet 2
ipx network 789
ipx helper-address
ipx helper-list
ipx type-20-input-checks
ipx type-20-output-checks
To adjust the IPX routing update timers, use the ipx update-time interface configuration command. To restore the default value, use the no form of this command.
ipx update-time interval| interval | Interval, in seconds, at which IPX routing updates are sent. The default is 60 seconds. The minimum interval is 10 seconds. |
60 seconds
Interface configuration
The ipx update-time command sets the routing update timer on a per-interface basis.
Routers exchange information about routes by sending broadcast messages when they are brought up and shut down, and periodically while they are running. The ipx update-time command lets you modify the periodic update interval. By default, this interval is 60 seconds (this default is defined by Novell).
You can set RIP timers only in a configuration in which all routers are our routers or in which the IPX routers allow configurable timers. The timers should be the same for all routers connected to the same cable segment.
The update value you choose affects the internal IPX timers as follows:
The concept of granularity is best explained by an example. (This example is illustrated in the "Example" section following.) If you have two interfaces in the router and you set the update timer on one to 20 seconds and the second to 30 seconds, the router wakes up every 20 seconds to try to send routing updates. So at time 0:00:20, the router sends an update out the first interface only, and at time 0:00:40 it sends updates out the first and second interfaces. The router does not wake up at 0:00:30 to see if it needs to send an update out the second interface. This means that routing updates are sent out the second interface at N:NN:40 and N:NN:00. That is, the interval alternates between 40 seconds and 20 seconds; it is never 30 seconds. The interval on the first interface is always 20 seconds.
The following example sets the update timers on two interfaces in the router. The update timer granularity would be 20 seconds because this is the lowest value specified.
interface serial 0
ipx update-time 40
interface ethernet 0
ipx update-time 20
show ipx interface
To have the router respond to a server's watchdog packets on behalf of a remote client, use the ipx watchdog-spoof interface configuration command. To disable spoofing, use the no form of this command.
ipx watchdog-spoofThis command has no arguments or keywords.
Disabled
Interface configuration
You can use the ipx watchdog-spoof command only on a serial interface on which dial-on-demand routing (DDR) has been enabled. Also, fast switching and autonomous switching must be disabled on the interface.
IPX watchdog packets are keepalive packets that are sent from servers to clients after a client session has been idle for approximately 5 minutes. On a DDR link, this would mean that a call would be made every 5 minutes, regardless of whether there were data packets to send. You can prevent these calls from being made by configuring the router to respond to the server's watchdog packets on a remote client's behalf. This is sometimes referred to as "spoofing the server."
The following example enables spoofing on serial interface 0:
interface serial 0
ipx watchdog-spoof
no ipx route-cache
ipx route-cache
To define an IPX NetBIOS access list filter, use the netbios access-list interface configuration command. To remove a filter, use the no form of the command.
netbios access-list host name {deny | permit} string| host | Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list host commands. |
| bytes | Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list bytes commands. |
| name | Name of the access list being defined. The name can be an alphanumeric string. |
| deny | Denies access if the conditions are matched. |
| permit | Permits access if the conditions are matched. |
| string | Character string that identifies one or more NetBIOS host names. It can be up to 14 characters long. The argument string can include the following wildcard characters:
· *--Match one or more characters. You can use this wildcard character only at the end of a string. · ?--Match any single character. |
| offset | Decimal number that indicates the number of bytes into the packet at which the byte comparison should begin. An offset of 0 indicates the beginning of the NetBIOS packet header, which is at the end of the IPX header. |
| byte-pattern | Hexadecimal pattern that represents the byte pattern to match. It can be up to 16 bytes (32 digits) long and must be an even number of digits. The argument byte-pattern can include the following wildcard character:
· **--Match any digits for that byte. |
No filters are predefined.
Global configuration
Keep the following points in mind when configuring IPX NetBIOS access control:
These filters apply only to IPX NetBIOS packets. They have no effect on LLC2 NetBIOS packets.
To delete an IPX NetBIOS access list, specify the minimum number of keywords and arguments needed to delete the proper list. For example, to delete the entire list, use the following command:
no netbios access-list {host | bytes} nameTo delete a single entry from the list, use the following command:
no netbios access-list host name {permit | deny} stringThe following example defines the IPX NetBIOS access list engineering:
netbios access-list host engineering permit eng-ws1 eng-ws2 eng-ws3
The following example removes a single entry from the engineering access list:
netbios access-list host engineering deny eng-ws3
The following example removes the entire engineering NetBIOS access list:
no netbios access-list host engineering
ipx netbios input-access filter
ipx netbios output-access filter
show ipx interface
To enable Enhanced IGRP on the router, use the network IPX-router configuration command. To disable Enhanced IGRP on the router, use the no form of this command.
network {network-number | all}| network-number | IPX network number |
| all | Enables the routing protocol for all IPX networks configured on the router |
Disabled
IPX-router configuration
Use the network command to enable the routing protocol specified in the ipx router command on each network.
The following commands disable RIP on network 10 and enable Enhanced IGRP on networks 10 and 20:
ipx router rip
no network 10
ipx router eigrp 12
network 10
network 20
ipx router
To check host reachability and network connectivity, use the ping privileged EXEC command.
ping [ipx] [address]| ipx | (Optional) Specifies the IPX protocol. |
| address | (Optional) Address of system to ping. |
Privileged EXEC
The privileged ping (IPX echo) command provides a complete ping facility for users who have system privileges.
The ping command works only on our routers running Software Release 8.2 or later.
Novell IPX devices that support the echo function defined in version 1.0 of the NLSP specification will respond to this command if you answer y to the prompt Novell Standard Echo that is displayed when you use the ping command. If you answer n to this prompt, Novell IPX devices will not respond.
To abort a ping session, type the escape sequence. By default, this is Ctrl-^ X. You enter this by simultaneously pressing the Ctrl, Shift, and 6 keys, letting go, and then pressing the X key.
Table 19-4 describes the test characters displayed in ping responses.
| Character | Meaning |
|---|---|
| ! | Each exclamation point indicates the receipt of a reply from the target address. |
| . | Each period indicates the network server timed out while waiting for a reply from the target address. |
| U | A destination unreachable error PDU was received. |
| C | A congestion experienced packet was received. |
| I | User interrupted the test. |
| ? | Unknown packet type. |
| & | Packet lifetime exceeded. |
The following sample display shows input to and output from the ping command:
Router# ping
Protocol [ip]: ipx
Target Novell Address: 211.0000.0c01.f4cf
Repeat Count [5]:
Datagram Size [100]:
Timeout in seconds [2]:
Verbose [n]:
Novell Standard Echo [n]:
Type escape sequence to abort.
Sending 5 100-byte Novell echoes to 211.0000.0c01.f4cf, timeout is 2 seconds.
!!!!!
Success rate is 100%, round trip min/avg/max = 1/2/4 ms.
ping (user)
To check host reachability and network connectivity, use the ping user EXEC command.
ping ipx {host | address}| ipx | Specifies the IPX protocol |
| host | Host name of system to ping |
| address | Address of system to ping |
EXEC
The user-level ping (packet internet groper function) command provides a basic ping facility for users who do not have system privileges. This command is equivalent to the nonverbose form of the privileged ping command. It sends five 100-byte ping packets.
The ping command works only on our routers running Software Release 8.2 or later. Novell IPX devices will not respond to this command.
You cannot ping a router from itself.
If the system cannot map an address for a host name, it will return an "%Unrecognized host or address" error message.
To abort a ping session, type the escape sequence. By default, this is Ctrl-^ X. You enter this by simultaneously pressing the Ctrl, Shift, and 6 keys, letting go, and then pressing the X key.
Table 19-5 describes the test characters displayed in ping responses.
| Character | Meaning |
|---|---|
| ! | Each exclamation point indicates receipt of a reply. |
| . | Each period indicates the network server timed out while waiting for a reply. |
| U | A destination unreachable error PDU was received. |
| C | A congestion experienced packet was received. |
| I | User interrupted the test. |
| ? | Unknown packet type. |
| & | Packet lifetime exceeded. |
The following sample display shows input to and output from the user ping command:
Router> ping ipx 211.0000.0c01.f4cf
Type escape sequence to abort.
Sending 5, 100-byte Novell Echoes to 211.0000.0c01.f4cf, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
ping (privileged)
To redistribute from one routing domain into another, and vice versa, use the redistribute IPX-router configuration command. To disable this feature, use the no form of this command.
redistribute {rip | eigrp autonomous-system-number | connected | static}| rip | Specifies the RIP protocol. |
| eigrp autonomous-system-number | Specifies the Enhanced IGRP protocol and the Enhanced IGRP autonomous system number. It can be a decimal integer from 1 to 65535. |
| connected | Specifies connected routes. |
| static | Specifies static routes. |
Redistribution is enabled by default between all routing domains except between separate Enhanced IGRP processes.
IPX-router configuration
Redistribution provides for routing information generated by one protocol to be advertised in another.
The only connected routes affected by this redistribute command are the routes not specified by the network command.
In the following example, RIP routing information is not redistributed:
ipx router eigrp 222
no redistribute rip
In the following example, Enhanced IGRP routes from autonomous system 100 are redistributed into Enhanced IGRP autonomous sytem 300:
router eigrp 300
redistribute eigrp 100
To display the active accounting or checkpointed database, use the show ipx accounting EXEC command.
show ipx accounting [checkpoint]| checkpoint | (Optional) Displays entries in the checkpointed database should be displayed. |
EXEC
The following is sample output from the show ipx accounting command:
Router# show ipx accounting
Source Destination Packets Bytes
0000C003.0000.0c05.6030 0000C003.0260.8c9b.4e33 72 2880
0000C001.0260.8c8d.da75 0000C003.0260.8c9b.4e33 14 624
0000C003.0260.8c9b.4e33 0000C001.0260.8c8d.da75 62 3110
0000C001.0260.8c8d.e7c6 0000C003.0260.8c9b.4e33 20 1470
0000C003.0260.8c9b.4e33 0000C001.0260.8c8d.e7c6 20 1470
Accounting data age is 6
Table 19-6 describes the fields shown in the display.
| Field | Description |
|---|---|
| Source | Source address of the packet. |
| Destination | Destination address of the packet. |
| Packets | Number of packets transmitted from the source address to the destination address. |
| Bytes | Number of bytes transmitted from the source address to the destination address. |
| Accounting data age is ... | Time since the accounting database has been cleared. It can be in one of the following formats: mm, hh:mm, dd:hh, and xw yd, where m is minutes, h is hours, d is days, and w is weeks. |
clear ipx accounting
ipx accounting
ipx accounting-list
ipx accounting-threshold
ipx accounting-transits
To display the contents of the IPX fast-switching cache, use the show ipx cache EXEC command.
show ipx cacheThis command has no arguments or keywords.
EXEC
The following is sample output from the show ipx cache command:
Router# show ipx cache
Novell routing cache version is 9
Destination Interface MAC Header
*1006A Ethernet 0 00000C0062E600000C003EB0064
*14BB Ethernet 1 00000C003E2A00000C003EB0064
Table 19-7 describes the fields shown in the display.
| Field | Description |
|---|---|
| Novell routing cache version is ... | Number identifying the version of the fast-switching cache table. It increments each time the table changes. |
| Destination | Destination network for this packet. Valid entries are marked by an asterisk (*). |
| Interface | Router interface through which this packet is transmitted. |
| MAC Header | Contents of this packet's MAC header. |
clear ipx cache
ipx route-cache
To display the neighbors discovered by Enhanced IGRP, use the show ipx eigrp neighbors EXEC command.
show ipx eigrp neighbors [servers] [autonomous-system-number | type number]| servers | (Optional) Displays the server list advertised by each neighbor. This is displayed only if the ipx sap incremental command is enabled on the interface on which the neighbor resides. |
| autonomous-system-number | (Optional) Autonomous system number. It can be a decimal integer from 1 to 65535. |
| type | (Optional) Interface type. |
| number | (Optional) Interface number. |
EXEC
The following is sample output from the show ipx eigrp neighbors command:
Router# show ipx eigrp neighbors
IPX EIGRP Neighbors for process 200
H Address Interface Hold Uptime Q Seq SRTT RTO
(secs) (h:m:s) Cnt Num (ms) (ms)
6 90.0000.0c02.096e Tunnel44444 13 0:30:57 0 21 9 20
5 80.0000.0c02.34f2 Fddi0 12 0:31:17 0 62 14 28
4 83.5500.2000.a83c TokenRing2 13 0:32:36 0 626 16 32
3 98.0000.3040.a6b0 TokenRing1 12 0:32:37 0 43 9 20
2 80.0000.0c08.cbf9 Fddi0 12 0:32:37 0 624 19 38
1 85.aa00.0400.153c Ethernet2 12 0:32:37 0 627 15 30
0 82.0000.0c03.4d4b Hssi0 12 0:32:38 0 629 12 24
Table 19-8 explains the fields in the display.
| Field | Description |
|---|---|
| process 200 | Autonomous system number specified in the ipx router configuration command. |
| H | Handle. An arbitrary and unique number inside this router that identifies the neighbor. |
| Address | IPX address of the Enhanced IGRP peer. |
| Interface | Interface on which the router is receiving hello packets from the peer. |
| Hold | Length of time, in seconds, that the router will wait to hear from the peer before declaring it down. If the peer is using the default hold time, this number will be less than 15. If the peer configures a nondefault hold time, it will be reflected here. |
| Uptime | Elapsed time, in hours, minutes, and seconds, since the local router first heard from this neighbor. |
| Q Cnt | Number of IPX Enhanced IGRP packets (Update, Query, and Reply) that the router is waiting to send. |
| Seq Num | Sequence number of the last Update, Query, or Reply packet that was received from this neighbor. |
| SRTT | Smooth round-trip time. This is the number of milliseconds it takes for an IPX Enhanced IGRP packet to be sent to this neighbor and for the local router to receive an acknowledgment of that packet. |
| RTO | Retransmission timeout, in milliseconds. This is the amount of time the router waits before retransmitting a packet from the retransmission queue to a neighbor. |
To display the Enhanced IGRP topology table, use the show ipx eigrp topology EXEC command.
show ipx eigrp topology [network-number]| network-number | (Optional) IPX network number whose topology table entry to display |
EXEC
The following is sample output from the show ipx eigrp topology command:
Router# show ipx eigrp topology
IPX EIGRP Topology Table for process 109
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
r - Reply status
P 42, 1 successors, FD is 0
via 160.0000.0c00.8ea9 (345088/319488), Ethernet0
P 160, 1 successor via Connected, Ethernet
via 160.0000.0c00.8ea9 (307200/281600), Ethernet0
P 165, 1 successors, FD is 307200
via Redistributed (287744/0)
via 160.0000.0c00.8ea9 (313344/287744), Ethernet0
P 164, 1 successors, flags: U, FD is 200
via 160.0000.0c00.8ea9 (307200/281600), Ethernet1
via 160.0000.0c01.2b71 (332800/307200), Ethernet1
P A112, 1 successors, FD is 0
via Connected, Ethernet2
via 160.0000.0c00.8ea9 (332800/307200), Ethernet0
P AAABBB, 1 successors, FD is 10003
via Redistributed (287744/0),
via 160.0000.0c00.8ea9 (313344/287744), Ethernet0
A A112, 0 successors, 1 replies, state: 0, FD is 0
via 160.0000.0c01.2b71 (307200/281600), Ethernet1
via 160.0000.0c00.8ea9 (332800/307200) , r, Ethernet1
Table 19-9 explains the fields in the output.
| Field | Description |
|---|---|
| Codes | State of this topology table entry. Passive and Active refer to the Enhanced IGRP state with respect to this destination; Update, Query, and Reply refer to the type of packet that is being sent. |
| P - Passive | No Enhanced IGRP computations are being performed for this destination. |
| A - Active | Enhanced IGRP computations are being performed for this destination. |
| U - Update | Indicates that an update packet was sent to this destination. |
| Q - Query | Indicates that a query packet was sent to this destination. |
| R - Reply | Indicates that a reply packet was sent to this destination. |
| r - Reply status | Flag that is set after the router has sent a query and is waiting for a reply. |
| 42, 160, and so on | Destination IPX network number. |
| successors | Number of successors. This number corresponds to the number of next hops in the IPX routing table. |
| FD | Feasible distance. This value is used in the feasibility condition check. If the neighbor's reported distance (the metric after the slash) is less than the feasible distance, the feasibility condition is met and that path is a feasible successor. Once the router determines it has a feasible successor, it does not have to send a query for that destination. |
| replies | Number of replies that are still outstanding (have not been received) with respect to this destination. This information appears only when the destination is in Active state. |
| state | Exact Enhanced IGRP state that this destination is in. It can be the number 0, 1, 2, or 3. This information appears only when the destination is Active. |
| via | IPX address of the peer who told the router about this destination. The first n of these entries, where n is the number of successors, are the current successors. The remaining entries on the list are feasible successors. |
| (345088/319488) | The first number is the Enhanced IGRP metric that represents the cost to the destination. The second number is the Enhanced IGRP metric that this peer advertised. |
| Ethernet0 | Interface from which this information was learned. |
The following is sample output from the show ipx eigrp topology command when you specify an IPX network number:
Router# show ipx eigrp topology 160
IPX-EIGRP topology entry for 160
State is Passive, Query origin flag is 1, 1 Successor(s)
Routing Descriptor Blocks:
Next hop is Connected (Ethernet0), from 0.0000.0000.0000
Composite metric is (0/0), Send flag is 0x0, Route is Internal
Vector metric:
Minimum bandwidth is 10000 Kbit
Total delay is 1000000 nanoseconds
Reliability is 255/255
Load is 1/255
Minimum MTU is 1500
Hop count is 0
Next hop is 164.0000.0c00.8ea9 (Ethernet1), from 164.0000.0c00.8ea9
Composite metric is (307200/281600), Send flag is 0x0, Route is External
This is an ignored route
Vector metric:
Minimum bandwidth is 10000 Kbit
Total delay is 2000000 nanoseconds
Reliability is 255/255
Load is 1/255
Minimum MTU is 1500
Hop count is 1
External data:
Originating router is 0000.0c00.8ea9
External protocol is RIP, metric is 1, delay 2
Administrator tag is 0 (0x00000000)
Flag is 0x00000000
Table 19-10 explains the fields in the output.
| Field | Description |
|---|---|
| 160 | IPX network number of the destination. |
| State is ... | State of this entry. It can be either Passive or Active. Passive means that no Enhanced IGRP computations are being performed for this destination, and Active means that they are being performed. |
| Query origin flag | Exact Enhanced IGRP state that this destination is in. It can be the number 0, 1, 2, or 3. This information appears only when the destination is Active. |
| Successors | Number of successors. This number corresponds to the number of next hops in the IPX routing table. |
| Next hop is ... | Indicates how this destination was learned. It can be one of the following:
|
|
Ethernet0 | Interface from which this information was learned. |
| from | Peer from whom the information was learned. For connected and redistributed routers, this is 0.0000.0000.0000. For information learned via Enhanced IGRP, this is the peer's address. Currently, for information learned via Enhanced IGRP, the peer's IPX address always matches the address in the "Next hop is" field. |
| Composite metric is | Enhanced IGRP composite metric. The first number is this router's metric to the destination, and the second is the peer's metric to the destination. |
| Send flag | Numeric representation of the "flags" field described in Table 19-9. It is 0 when nothing is being sent, 1 when an Update is being sent, 3 when a Query is being sent, and 4 when a Reply is being sent. Currently, 2 is not used. |
| Route is ... | Type of router. It can be either internal or external. Internal routes are those that originated in an Enhanced IGRP autonomous system, and external are routes that did not. Routes learned via RIP are always external. |
| This is an ignored route | Indicates that this path is being ignored because of filtering. |
| Vector metric: | This section describes the components of the Enhanced IGRP metric. |
| Minimum bandwidth | Minimum bandwidth of the network used to reach the next hop. |
| Total delay | Delay time to reach the next hop. |
| Reliability | Reliability value used to reach the next hop. |
| Load | Load value used to reach the next hop. |
| Minimum MTU | Minimum MTU size of the network used to reach the next hop. |
| Hop count | Number of hops to the next hop. |
| External data | This section describes the original protocol from which this route was redistributed. It appears only for external routes. |
| Originating router | Network address of the router that first distributed this route into Enhanced IGRP. |
| External protocol..metric..delay | External protocol from which this route was learned. The metric will match the external hop count displayed by the show ipx route command for this destination. The delay is the external delay. |
| Administrator tag | Not currently used. |
| Flag | Not currently used. |
show ipx route
To display the status of the IPX interfaces configured in the router and the parameters configured on each interface, use the show ipx interface EXEC command.
show ipx interface [type number]| type | (Optional) Interface type. It can be one of the following types: asynchronous, dialer, Ethernet (IEEE 802.3), FDDI, loopback, null, serial, tokenring, or tunnel. |
| number | (Optional) Interface number. |
EXEC
The following is sample output from the show ipx interface command:
Router# show ipx interface ethernet 1
Ethernet1 is up, line protocol is up
IPX address is C03.0000.0c05.6030, NOVELL-ETHER [up] line-up, RIPPQ: 0, SAPPQ : 0
Delay of this Novell network, in ticks is 1
IPXWAN processing not enabled on this interface.
IPX SAP update interval is 1 minute(s)
IPX type 20 propagation packet forwarding is disabled
Outgoing access list is not set
IPX Helper access list is not set
SAP Input filter list is not set
SAP Output filter list is not set
SAP Router filter list is not set
SAP GNS output filter list is not set
Input filter list is not set
Output filter list is not set
Router filter list is not set
Netbios Input host access list is not set
Netbios Input bytes access list is not set
Netbios Output host access list is not set
Netbios Output bytes access list is not set
Update time is 60 seconds
IPX accounting is enabled
IPX fast switching is configured (enabled)
IPX SSE switching is disabled
Table 19-11 describes the fields shown in the display.
| Field | Description |
|---|---|
| Ethernet1 is ..., line protocol is ... | Type of interface and whether it is currently active and inserted into the network (up) or inactive and not inserted (down). |
| IPX address is ... | Network and node address of the local router interface, followed by the type of encapsulation configured on the interface and the interface's status. Refer to the ipx network command for a list of possible values. |
| NOVELL-ETHER | Type of encapsulation being used on the interface, if any. |
| [up] line-up | Indicates whether IPX routing is enabled or disabled on the interface. "line-up" indicates that IPX routing has been enabled with the ipx routing command. "line-down" indicates that it is not enabled. The word in square brackets provides more detail about the status of IPX routing when it is in the process of being enabled or disabled. |
| RIPPQ: | Number of packets in the RIP queue. |
| SAPPQ: | Number of packets in the SAP queue. |
| Secondary address is ... | Address of a secondary network configured on this interface, if any, followed by the type of encapsulation configured on the interface and the interface's status. Refer to the ipx network command for a list of possible values. This line is displayed only if you have configured a secondary address with the ipx network command. |
| Delay of this Novell network, in ticks, ... | Value of the ticks field (configured with the ipx delay command). |
| IPXWAN processing... | Indicates whether IPXWAN processing has been enabled on this interface with the ipx ipxwan command. |
| IPX SAP update interval | Indicates the frequency of outgoing SAP updates (configured with the ipx sap-interval command). |
| IPX type 20 propagation packet forwarding... | Indicates whether forwarding of IPX type 20 propagation packets (used by NetBIOS) is enabled or disabled on this interface, as configured with the ipx type-20-propagation command. |
| Outgoing access list | Indicates whether an access list has been enabled with the ipx access-group command. |
| IPX Helper access list | Number of the broadcast helper list applied to the interface with the ipx helper-list command. |
| SAP Input filter list | Number of the input SAP filter applied to the interface with the ipx input-sap-filter command. |
| SAP Output filter list | Number of the output SAP filter applied to the interface with the ipx output-sap-filter command. |
| SAP Router filter list | Number of the router SAP filter applied to the interface with the ipx router-sap-filter command. |
| SAP GNS output filter | Number of the Get Nearest Server (GNS) response filter applied to the interface with the ipx output-gns-filter command. |
| Input filter | Number of the input filter applied to the interface with the ipx input-network-filter command. |
| Output filter | Number of the output filter applied to the interface with the ipx output-network-filter command. |
| Router filter | Number of the router entry filter applied to the interface with the ipx router-filter command. |
| Netbios Input host access list | Name of the IPX NetBIOS input host filter applied to the interface with the ipx netbios input-access-filter host command. |
| Netbios Input bytes access list | Name of the IPX NetBIOS input bytes filter applied to the interface with the ipx netbios input-access-filter bytes command. |
| Netbios Output host access list | Name of the IPX NetBIOS output host filter applied to the interface with the ipx netbios output-access-filter host command. |
| Netbios Output bytes access list | Name of the IPX NetBIOS output bytes filter applied to the interface with the ipx netbios output-access-filter bytes command. |
| Update time | How often the router sends RIP updates, as configured with the ipx update-time command. |
| Watchdog spoofing ... | Indicates whether watchdog spoofing is enabled of disabled for this interface, as configured with the ipx watchdog-spoof command. This information is displayed only on serial interfaces. |
| IPX accounting | Indicates whether IPX accounting has been enabled with the ipx accounting command. |
| IPX Fast switching IPX Autonomous switching | Indicates whether IPX fast switching is enabled (default) or disabled for this interface, as configured with ipx route-cache command. (If IPX autonomous switching is enabled, it is configured with the ipx route-cache cbus command.) |
| IPX SSE switching | Indicates whether IPX SSE switching is enabled for this interface, as configured with the ipx route-cache sse command. |
access-list (standard)
access-list (extended)
access-list (SAP)
ipx accounting
ipx delay
ipx encapsulation
ipx helper-list
ipx input-network-filter
ipx input-sap-filter
ipx ipxwan
ipx netbios input-access-filter
ipx netbios output-access-filter
ipx network
ipx output-gns-filter
ipx output-network-filter
ipx output-rip-delay
ipx output-sap-filter
ipx route-cache
ipx router filter
ipx router-sap-filter
ipx routing
ipx sap-interval
ipx update-time
ipx watchdog-spoof
netbios access-list
To display the contents of the IPX routing table, use the show ipx route user EXEC command.
show ipx route [network]| network | (Optional) Number of the network whose routing table entry you want to display. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can just enter AA. |
EXEC
The following is sample output from the show ipx route command:
Router> show ipx route
Codes: C - Connected primary network, c - Connected secondary network
R - RIP, E - EIGRP, S - static,8 Total IPX routes
No parallel paths allowed Novell routing algorithm variant in use
E Net 1 [307200/0] via 2.0000.0c05.84b6, age 0:01:25,
1 uses, Ethernet2
C Net 2 (NOVELL-ETHER), is directly connected, 30 uses, Ethernet2
E Net 3 [2195456/0] via 2.0000.0c05.84b6, age 0:01:25,
1 uses, Ethernet2
E Net 11 [281600/0] via 2.0000.0c05.84b6, age 0:01:25,
1 uses, Ethernet2
c Net 2000 (SAP), is directly connected, 3 uses, Ethernet2
R Net 22 [1/1] via 2.0000.0c05.84b6, 13 sec, 1 uses, Ethernet2
C Net 55 (NOVELL-ETHER), is directly connected, 30 uses, Ethernet3
S Net 70 via 55.0011.0022.0033, 1 uses, Ethernet3
Table 19-12 describes the fields shown in the display.
| Field | Description |
|---|---|
| Codes | Codes defining how the route was learned. |
| C | Directly connected primary network. |
| c | Directly connected secondary network |
| R | Route learned from a RIP update. |
| E | Route learned from an Enhanced IGRP update. |
| S | Statically defined route via the ipx route command. |
| W | Directly connected route determined via IPXWAN. |
| 8 Total IPX routes | Numbers of routes in the IPX routing table. |
| No parallel paths allowed | Maximum number of parallel paths for which the router has been configured with the ipx maximum-paths command. |
| Novell routing algorithm variant in use | Indicates whether the router is using the IPX-compliant routing algorithms (default). |
| Net 1 | Network to which the route goes. |
| [3/2] | Delay/Metric. Delay is the number of IBM clock ticks (each tick is 1/18 seconds) reported to the destination network. Metric is the number of hops reported to the same network. Delay is used as the primary routing metric, and the metric (hop count) is used as a tie breaker. |
| via network.node | Address of a router that is the next hop to the remote network. |
| age | Amount of time, in hours, minutes, and seconds, that has elapsed since information about this network was last received. |
| uses | Number of times this network has been looked up in the route table. This field is incremented when a packet is process-switched, even if the packet is eventually filtered and not sent. As such, this field represents a fair estimate of the number of times a route gets used. |
| Ethernet0 | Interface through which packets to the remote network will be sent. |
| (NOVELL-ETHER) (HDLC) (SAP) (SNAP) | Encapsulation (frame) type. This is shown only for directly connected networks. |
| is directly connected | Indicates that the network is directly connected to the router. |
clear ipx route
ipx maximum-paths
ipx route
To list the IPX servers discovered through SAP advertisements, use the show ipx servers EXEC command.
show ipx servers [sorted [name | net | type]]| sorted | (Optional) Sorts the display of IPX servers according to the keyword that follows. |
| name | (Optional) Displays the IPX servers alphabetically by server name. |
| net | (Optional) Displays the IPX servers numerically by network number. |
| type | (Optional) Displays the IPX servers numerically by SAP service type. This is the default. |
type
EXEC
The following is sample output from the show ipx servers command:
Router> show ipx servers
Codes: R - RIP, E - EIGRP, C - connected, S - static, 5 Total IPX routes
No parallel paths allowed Novell routing algorithm variant in use
E Net 42 [345088/2] via 160.0000.0c00.8ea9, age 2d21 1 uses, Ethernet0
C Net FFFF01 (NOVELL-ETHER), is directly connected, 33 uses, Ethernet3
R Net E04 [120/2] via 165.0000.0c01.d879, 17 sec, 1 uses, Ethernet0
R Net E02 [120/2] via 165.0000.0c01.d879, 17 sec, 2 uses, Ethernet0
R Net E03 [120/2] via 165.0000.0c01.d879, 17 sec, 57 uses, Ethernet0
C Net CC00C1 (HDLC), is directly connected, 0 uses, serial3, (down)
Table 19-13 describes the fields shown in the display.
| Field | Description |
|---|---|
| Codes | Codes defining how the route was learned. |
| R | Route learned from a RIP update. |
| E | Route learned via Enhanced IGRP. |
| C | Directly connected network. |
| S | Statically defined route via the ipx route command. |
| No parallel paths allowed | Maximum number of parallel paths for which the router has been configured with the ipx maximum-paths command. |
| Novell routing algorithm variant in use | Indicates whether the router is using the IPX-compliant routing algorithms (default). |
| sec | Number of seconds that have elapsed since information about this network was last received. |
| uses | Fair estimate of the number of times a route gets used. It actually indicates the number of times the route has been selected for use prior to operations such as access list filtering. |
| Ethernet0 | Possible interface through which updates to the remote network will be sent. |
| (NOVELL-ETHER) (HDLC) | Encapsulation type. This is shown only for directly connected networks. |
| is directly connected | Indicates that the network is directly connected to the router. |
| Net E04 | Network to which the route goes. |
| [345088/2] | The first number is the Enhanced IGRP metric, and the second number is the external hop count (for routes learned from Enhanced IGRP). The external hop count is the hop count that was advertised when this destination first entered the Enhanced IGRP autonomous system. If the external hop count is 0, this is an internal Enhanced IGRP route. When this destination is announced via RIP by this router, the router will add one to this value and use the result as the RIP hop count. The external hop count is not incremented when the destination is advertised via Enhanced IGRP. |
| [120/2] | Ticks/metric (for routes learned from RIP). Ticks are the number of IBM clock ticks (1/18th second). When ipx algorithms is enabled, hop count is used as a tie-breaker between routes if the tick count is the same. The metric is the IPX metric used in making routing decisions. |
| age | (For routes learned from Enhanced IGRP only.) Length of time since this route was first learned. The time is represented in the format hh:mm:ss until 24 hours have elapsed, after which it is represented dddhh until one week has elapsed. After one week, the age is represented wwwdd. |
| via network.node | Address of a router that is the next hop to the remote network. |
ipx sap
To display information about the number and type of IPX packets transmitted and received by the router, use the show ipx traffic user EXEC command.
show ipx trafficThis command has no arguments or keywords.
EXEC
The following is sample output from the show ipx traffic command:
Router> show ipx traffic
Rcvd: 644 total, 1705 format errors, 0 checksum errors, 0 bad hop count,
0 packets pitched, 644 local destination, 0 multicast
Bcast: 589 received, 324 sent
Sent: 380 generated, 0 forwarded
0 encapsulation failed, 4 no route
SAP: 1 SAP requests, 1 SAP replies
61 SAP advertisements received, 120 sent
0 SAP flash updates sent, 0 SAP poison sent
0 SAP format errors
RIP: 0 RIP format errors
Echo: Rcvd 55 requests, 0 replies
Sent 0 requests, 55 replies
0 unknown, 0 SAPs throttled, freed NDB len 0
Watchdog:
0 packets received, 0 replies spoofed
Queue lengths: IPX input: 0, SAP 0, RIP 0, GNS 0
Total length for SAP throttling purposes: 0/(no preset limit)
EIGRP: Total received 0, sent 0
Updates received 0, sent 0
Queries received 0, sent 0
Replies received 0, sent 0
SAPs received 0, sent 0
Table 19-14 describes the fields that might possibly be shown in the display.
| Field | Description |
|---|---|
| Rcvd: | Description of the packets the router has received. |
| 644 total | Total number of packets the router has received. |
| 1705 format errors | Number of bad packets discarded (for example, packets with a corrupted header). |
| 0 checksum errors | Number of packets containing a checksum error. This should always be 0, because IPX does not use a checksum. |
| 0 bad hop count | Number of packets discarded because their hop count exceeded 16 (that is, the packets timed out). |
| 0 packets pitched | Number of times the router received its own broadcast packet. |
| 644 local destination | Number of packets sent to the local broadcast address or specifically to the router. |
| 0 multicast | Number of packets received that were addressed to multiple destinations. |
| Bcast: | Description of the broadcast packets the router has received and sent. |
| 589 received | Number of broadcast packets received. |
| 324 sent | Number of broadcast packets sent. It includes broadcast packets the router is either forwarding or has generated. |
| Sent: | Description of those packets that the router generated and then sent, and also those the router has received and then routed to other destinations. |
| 380 generated | Number of packets the router transmitted that it generated itself. |
| 0 forwarded | Number of packets the router transmitted that it forwarded from other sources. |
| 0 encapsulation failed | Number of packets the router was unable to encapsulate. |
| 4 no route | Number of times the router could not locate a route to the destination in the routing table. |
| SAP: | Description of the SAP packets the router has sent and received. |
| 1 SAP requests | Number of SAP requests the router has received. |
| 1 SAP replies | Number of SAP replies the router has sent in response to SAP requests. |
| 61 SAP advertisements received | Number of SAP advertisements the router has received from another router. |
| 120 sent | Number of SAP advertisements the router has generated and then sent. |
| 0 SAP flash updates sent | Number of SAP advertisements the router has generated and then sent as a result of a change in its routing table. |
| 0 SAP poison sent | Number of times the router has generated an update indicating that a service is no longer reachable. |
| 0 SAP format errors | Number of SAP advertisements that were incorrectly formatted. |
| RIP: | Description of the RIP packets the router has sent and received. |
| 0 RIP format errors | Number of RIP packets that were incorrectly formatted. |
| freed NDB length | Number of Network Descriptor Blocks (NDBs) that have been removed from the network but still need to be removed from the router's routing table. |
| Watchdog: | Description of the watchdog packets the router has handled. |
| 0 packets received | Number of watchdog packets the router has received from IPX servers on the local network. |
| 0 replies spoofed | Number of times the router has responded to a watchdog packet on behalf of the remote client. |
| Echo: | Description of the ping replies and requests the router has sent and received. |
| Rcvd 55 request 0 replies | Number of ping requests and replies received by the router. |
| Sent 0 requests, 55 replies | Number of ping requests and replies sent by the router. |
| 0 unknown | Number of incomprehensible ping packets received by the router. |
| 0 SAPs throttled | Number of ping packets discarded because they exceeded buffer capacity. |
| Queue lengths | Description of outgoing packets currently in buffers that are waiting to be processed. |
| IPX input | Number of incoming packets waiting to be processed. |
| SAP | Number of outgoing SAP packets waiting to be processed. |
| RIP | Number of outgoing RIP packets waiting to be processed. |
| GNS | Number of outgoing GNS packets waiting to be processed. |
| Total length for SAP throttling purposes | Maximum number of outgoing SAP packets allowed in the buffer. Any packets received beyond this number are discarded. |
| EIGRP: | Description of the Enhanced IGRP packets the router has sent and received. |
| Updates | Number of Enhanced IGRP updates the router has sent and received. |
| Queries | Number of Enhanced IGRP queries the router has sent and received. |
| Replies | Number of Enhanced IGRP replies the router has sent and received. |
| SAPs | Number of SAP packets the router has sent to and received from Enhanced IGRP neighbors. |
| unknown counter | Number of packets the router was unable to forward, for example, because of a misconfigured helper address or because no route was available. |
To display a summary of Silicon Switch Processor (SSP) statistics, use the show sse summary EXEC command.
show sse summaryThis command has no arguments or keywords.
EXEC
The following is sample output from the show sse summary command:
Router# show sse summary
SSE utilization statistics
Program words Rewrite bytes Internal nodes Depth
Overhead 499 1 8
IP 0 0 0 0
IPX 0 0 0 0
SRB 0 0 0 0
CLNP 0 0 0 0
IP access lists 0 0 0
Total used 499 1 8
Total free 65037 262143
Total available 65536 262144
Free program memory
[499..65535]
Free rewrite memory
[1..262143]
Internals
75032 internal nodes allocated, 75024 freed
SSE manager process enabled, microcode enabled, 0 hangs
Longest cache computation 4ms, longest quantum 160ms at 0x53AC8
|
|