|
|
This chapter takes you through first-time startup. Use the information you entered onto the Global Configuration Worksheet and the Interface Configuration Worksheet as you interact with the System Configuration Dialog. If you have not completed the worksheets, read the chapter "Preparing for First-Time Startup" before starting up.
This chapter includes sample worksheets that have been filled in to show you how this information is used when the setup command facility runs through the System Configuration Dialog.
The first time you start up the system, the setup command facility operates automatically. An interactive dialog, called the System Configuration Dialog, is displayed on the screen of the system console. The dialog navigates you through the configuration process by prompting you for the information you should have already determined and recorded on the configuration worksheets. The setup command facility also provides default values and help text for the configuration parameters, as described later in this section.
The setup command facility knows which interfaces are installed and prompts you for configuration information for each installed interface. When you finish configuring one interface, the setup command software prompts you for the next interface and continues until they are all configured.
At first-time startup, you must do the following:
For many of the prompts in the System Configuration Dialog of the setup command facility, default answers appear in square brackets following the question. By pressing the Return key, you accept the defaults. If the system was previously configured, the defaults that appear are the currently configured values. If you are configuring the system for the first time, the factory defaults are provided. If there is no factory default, as in the case of passwords, nothing is displayed after the question mark.
At any time during use of the setup command facility, you can request help by typing a question mark (?) at a prompt. If the prompt requires a Yes or No answer, no further help is available. However, if the prompt offers a range of acceptable answers, the help facility will give you some guidance. For example, if you are prompted to select the number of bits in a subnet mask, the help facility might inform you that you can choose a decimal number between 0 and 16.
Before powering up your system, check for correct AC power voltages.
Now you can safely power up your system by flipping the switch on the back of the router.
When you first power up your console and network router, a script similar to the following appears on the screen. The script shown is for a Cisco 3000 with an IGS-BFPX image. The first section of the script displays the banner information, including the software version and the System Configuration Dialog. (A sample of the complete configuration script is included at the end of this chapter.)
Restricted Rights Legend
Use, duplication, or disclosure by the Government is subject
to restrictions as set forth in subparagraph (c) of the
Commercial Computer Software - Restricted Rights clause at
FAR sec. 52.227-19 and subparagraph (c) (ii) of the Rights
in Technical Data and Computer Software clause at
DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 W. Tasman Drive
San Jose, California
Cisco Internetwork Operating System Software
IOS (tm) 3000-BPRX Software, Version 10.0(1.0)
Copyright (c) 1986-1994 by cisco Systems, Inc.
Compiled Tue 24-May-94 06:34 by daveu
The next portion of the script lists installed hardware and software options, such as bridging and X.25. The system presents the appropriate interfaces for these options during the configuration process.
cisco 3000 (68030) processor (revision A) with 8192K/2048K bytes of memory.
Processor board serial number 00743954
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
ISDN software, Version 1.0.
Bridging software.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
1 Ethernet/IEEE 802.3 interface.
2 Serial network interfaces.
1 ISDN Basic Rate interface.
128K bytes of non-volatile configuration memory.
4096K bytes of flash memory sized on embedded flash.
Configuration register is 0x10F
The System Configuration Dialog appears next, and prompts for configuration information. The router gives you the opportunity to view the configuration, if any, for each interface. To accept the default settings, which appear in square brackets, press the Return key. The following example shows an AGS+ with four interfaces: TokenRing, Ethernet, Serial, and FDDI.
- System Configuration Dialog -
At any point you may enter a question mark '?' for help.
Refer to the 'Getting Started' Guide for additional help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes]:
First, would you like to see the current interface summary? [yes]:
Any interface listed with OK? value "NO" does not have a valid configuration.
Interface IP-Address OK? Method Status Protocol
TokenRing0 unassigned YES not set down down
Ethernet0 unassigned YES not set down down
Serial0 unassigned YES not set down down
Fddi0 unassigned YES not set down down
At this point, you can choose not to continue with the System Configuration Dialog and exit by answering No at the prompt. To begin the initial configuration process, answer Yes. You can press Ctrl-C to abort the process at any time. Ctrl-C returns you to the privileged EXEC prompt (router#). Refer to the Router Products Configuration Guide for information about configuring the router. Refer to the publication Protocol Translator Configuration Guide and Command Reference for information about configuring protocol translation.
If a --More-- prompt appears, press the space bar to continue.
You are prompted for global parameters at the console. Enter the values you wrote in on your Global Configuration Worksheet.
You are prompted for parameters for each installed interface at the console. Enter the values you wrote in on your Interface Configuration Worksheet.
When you complete the configuration process for all installed interfaces on your router, the setup command facility shows you the configuration command script that was created. It also asks you if you want to use this configuration. If you answer Yes, the configuration is saved to nonvolatile memory. If you answer No, the configuration is not saved and the process begins again. There is no default for this prompt; you must answer either Yes or No.
Once you have answered Yes to this last question, your system is now ready to be used. If you want to modify the configuration you have just established, see the chapter "Where to Go from Here."
This section contains a sample first-time startup configuration using sample completed worksheets. Figure 3-1 shows a completed Global Configuration Worksheet and Figure 3-2 shows a completed Interface Configuration Worksheet. These samples include the actual screen output for the setup command facility at first-time startup. The screen output includes both the interactive configuration process and the resulting script that was created. The sample output is from a Cisco 3000 running an IGS-BFPX image with an ISDN BRI.
In the sample System Configuration Dialog, when it appears that no response was made, the user pressed the Return key to accept the default.
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Refer to the 'Getting Started' Guide for additional help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes]:
First, would you like to see the current interface summary? [yes]:
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Protocol
BRI0 unassigned YES not set down down
Ethernet0 unassigned YES not set down down
Serial0 unassigned YES not set down down
Serial1 unassigned YES not set down down
Configuring global parameters:
Enter host name [Router]: sandbox
Enter enable password: shovel
Enter virtual terminal password: pail
Configure SNMP Network Management? [no]: yes
Configure XRemote font servers? [no]: yes
Enter a font server IP address or press RETURN to exit: 123.123.123.246
Configure DECnet? [no]: yes
Your area number [1]:
Your node number [1]:
Area (level 2) routing? [no]: yes
Configure IP? [yes]:
Configure IGRP routing? [yes]:
Your IGRP autonomous system number [1]: 15
Configure IPX? [no]: yes
Configure XNS? [no]: yes
Configure AppleTalk? [no]: yes
Multizone networks? [no]: yes
Configure Apollo? [no]: yes
Apollo routing number [12345]: 123
Configure CLNS? [yes]:
CLNS router tag [area_1]: pubsgroup
CLNS domain [49]: 72.8885
CLNS area [0001]: 0013
CLNS station id [0000.0C01.0D1D]: 72.8885.0000.0C01.0D1D.00
Configure Vines? [no]: yes
Configure bridging? [no]: yes
Configure LAT? [no]: yes
Configuring interface parameters:
Configuring interface Ethernet0:
Is this interface in use? [yes]:
Configure IP on this interface? [yes]:
IP address for this interface: 131.108.6.67
Number of bits in subnet field [0]:
Class B network is 131.108.0.0, 0 subnet bits; mask is 255.255.0.0
Configure DECnet on this interface? [yes]:
DECnet cost [10]:
Configure IPX on this interface? [yes]:
Novell network number [2]:
Configure XNS on this interface? [yes]:
XNS network number [2]:
Configure AppleTalk on this interface? [yes]:
Extended AppleTalk network? [no]: yes
AppleTalk starting cable range [4172]: 0
Configure Apollo on this interface? [no]:
Configure CLNS on this interface? [yes]:
Configure Vines on this interface? [yes]:
Configure bridging on this interface? [yes]:
Configure LAT on this interface? [no]: yes
!
Configuring interface Serial0:
Is this interface in use? [yes]:
Configure IP on this interface? [yes]:
Configure IP unnumbered on this interface? [no]:
IP address for this interface: 131.108.97.67
Number of bits in subnet field [0]:
Class B network is 131.108.0.0, 0 subnet bits; mask is 255.255.0.0
Configure DECnet on this interface? [yes]: no
Configure IPX on this interface? [yes]: no
Configure XNS on this interface? [yes]: no
Configure AppleTalk on this interface? [yes]:
Extended AppleTalk network? [no]:
AppleTalk network number [1]:
AppleTalk zone name [twilight]:
Configure Apollo on this interface? [no]:
Configure CLNS on this interface? [yes]:
Configure Vines on this interface? [yes]:
Configure bridging on this interface? [yes]:
Configure LAT on this interface? [no]: yes
!
Configuring interface Serial1:
Is this interface in use? [yes]:
Configure IP on this interface? [yes]: no
Configure IP unnumbered on this interface? [no]: yes
Interface name Ethernet0
Configure DECnet on this interface? [no]:
Configure IPX on this interface? [yes]: no
Configure XNS on this interface? [yes]: no
Configure AppleTalk on this interface? [yes]:
Extended AppleTalk network? [no]: yes
AppleTalk starting cable range [4172]: 0
AppleTalk network number [1]:
AppleTalk zone name [dawn]:
Configure Apollo on this interface? [no]:
Configure CLNS on this interface? [yes]: no
Configure Vines on this interface? [yes]: no
Configure bridging on this interface? [yes]: no
Configure LAT on this interface? [no]: yes
[OK]
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
First-time startup is complete. Your router is now ready for use. If you want to change the configuration you have just established during first-time startup, use the setup command facility described in the chapter "Where to Go from Here." To perform advanced configurations, use the configure command, as described in the publications Router Products Configuration Guide and Router Products Command Reference. To configure protocol translation, refer to the publication Protocol Translator Configuration Guide and Command Reference.
|
|