|
|
Table Of Contents
Cisco MDS 9000 Family Release Notes
for Cisco MDS SAN-OS Release 3.2(3a)Determining the Software Version
Selecting the Correct Software Image for an MDS 9100 Series Switch
Selecting the Correct Software Image for an MDS 9200 Series Switch
Selecting the Correct Software Image for an MDS 9500 Series Switch
Migrating from Supervisor-1 Modules to Supervisor-2 Modules
Configuring Generation 2 Switching Modules
Upgrading Your Cisco MDS SAN-OS Software Image
Upgrading Your Version of Cisco Fabric Manager
Reconfiguring SSM Ports Before Upgrading to SAN-OS Release 3.2(3a)
Upgrading the SSI Image on Your SSM
Upgrading a Switch with Insufficient Space for Two Images on the Bootflash
Upgrading a Cisco MDS 9124 Switch
Performing a Disruptive Upgrade on a Single Supervisor MDS Family Switch
Downgrading Your Cisco MDS SAN-OS Software Image
General Downgrading Guidelines
Downgrading the SSI Image on Your SSM
New Features in Cisco MDS SAN-OS Release 3.2(3a)
Regulatory Compliance and Safety Information
Installation and Configuration Note
Obtaining Documentation, Obtaining Support, and Security Guidelines
Cisco MDS 9000 Family Release Notes
for Cisco MDS SAN-OS Release 3.2(3a)
Release Date: February 4, 2008
Part Number: OL-14116-05
This document describes the caveats and limitations for switches in the Cisco MDS 9000 Family. Use this document in conjunction with documents listed in the "Related Documentation" section.
Note
Release notes are sometimes updated with new information on restrictions and caveats. Refer to the following website for the most recent version of the Cisco MDS 9000 Family Release Notes: http://www.cisco.com/en/US/products/hw/ps4159/ps4358/prod_release_notes_list.html
Contents
This document includes the following sections:
•
•
•
•
•
•
Introduction
The Cisco MDS 9000 Family of Multilayer Directors and Fabric Switches provides industry-leading availability, scalability, security, and management, allowing you to deploy high performance storage-area networks with lowest total cost of ownership. Layering a rich set of intelligent features onto a high performance, protocol agnostic switch fabric, the Cisco MDS 9000 Family addresses the stringent requirements of large data center storage environments: uncompromising high availability, security, scalability, ease of management, and seamless integration of new technologies.
The Cisco MDS 9000 Family SAN-OS is the underlying system software that powers the Cisco MDS 9500 Series, 9200 Series, and 9100 Series multilayer switches. The Cisco SAN-OS provides intelligent networking features, such as multiprotocol and multitransport integration, virtual SANs (VSANs), advanced security, sophisticated debug analysis tools, and unified SAN management.
Components Supported
Table 1 lists the SAN-OS software part number and hardware components supported by the Cisco MDS 9000 Family.
Note
Table 1 Cisco MDS 9000 Family Supported Software and Hardware Components
Software
M95S2K9-3.2.3a
MDS 9500 Supervisor/Fabric-2, SAN-OS software.
MDS 9500 Series only
M95S1K9-3.2.3a
MDS 9500 Supervisor/Fabric-I, SAN-OS software.
MDS 9500 Series only
M92S2K9-3.2.3a
MDS 9222 Supervisor/Fabric-2, SAN-OS software.
MDS 9200 Series only
M92S1K9-3.2.3a
MDS 9216 Supervisor/Fabric-I, SAN-OS software.
MDS 9200 Series only
M91S2K9-3.2.3a
MDS 9100 Supervisor/Fabric-2, SAN-OS software.
MDS 9100 Series only
M91S1K9-3.2.3a
MDS 9100 Supervisor/Fabric-I, SAN-OS software.
MDS 9100 Series only
License
M9500ENT1K9
Enterprise package.
MDS 9500 Series
M9200ENT1K9
Enterprise package.
MDS 9200 Series
M9100ENT1K9
Enterprise package.
MDS 9100 Series
M9500FIC1K9
Mainframe package.
MDS 9500 Series
M9200FIC1K9
Mainframe package.
MDS 9200 Series
M9100FIC1K9
Mainframe package.
MDS 9100 Series
M9100FIC1EK9
FICON license.
MDS 9100 Series
M9500FMS1K9
Fabric Manager Server package.
MDS 9500 Series
M9200FMS1K9
Fabric Manager Server package.
MDS 9200 Series
M9100FMS1K9
Fabric Manager Server package.
MDS 9100 Series
M9500EXT1K9
SAN Extension over IP package for IPS-8 module.
MDS 9500 Series
M9200EXT1K9
SAN Extension over IP package for IPS-8 module.
MDS 9200 Series
License
M9500EXT14K9
SAN Extension over IP package for IPS-4 module.
MDS 9500 Series
M9200EXT14K9
SAN Extension over IP package for IPS-4 module.
MDS 9200 Series
M9500EXT12K9
SAN Extension over IP package for MPS-14/2 module.
MDS 9500 Series
M9200EXT12K9
SAN Extension over IP package for MPS-14/2 module.
MDS 9200 Series
M9500EXT1AK9
SAN Extension over IP package for MSM-18/4 module or MSFM-18/4 FIPS module.
MDS 9500 Series
M9200EXT1AK9
SAN Extension over IP package for MSM-18/4 module or MSFM-18/4 FIPS module.
MDS 9200 Series
M9500SSE1K9
Storage Services Enabler package.
MDS 9500 Series with SSM
M9200SSE1K9
Storage Services Enabler package.
MDS 9200 Series with SSM
M9500SME1MK9
Cisco Storage Media Encryption package for MSM-18/4 module
MDS 9500 Series with MSM
M9200SME1MK9
Cisco Storage Media Encryption package for MSM-18/4 module
MDS 9200 Series with MSM
M9200SME1FK9
Cisco Storage Media Encryption package for fixed slot
MDS 9222i Switch only
M95DMMS1K9
Data Mobility Manager (DMM)
MDS 9500 Series with SSM
M92DMMS1K9
Data Mobility Manager (DMM)
MDS 9200 Series with SSM
M95DMMTS1K9
Data Mobility Manager (DMM) for 180 days
MDS 9500 Series with SSM
M92DMMTS1K9
Data Mobility Manager (DMM) for 180 days
MDS 9200 Series with SSM
M9124PL8-4G
On-Demand Ports Activation License
MDS 9124 Switch
M9134PL8-4G
On-Demand Ports Activation License
MDS 9134 Switch
M9134PL2-10G
On-Demand Ports Activation License
MDS 9134 Switch
HP-PL12-4G
On-Demand Ports Activation License
Cisco Fabric Switch for HP c-Class BladeSystem only
IBM-PL10-4G
On-Demand Ports Activation License
Cisco Fabric Switch for IBM BladeCenter only
Chassis
DS-C9513
MDS 9513 director (13-slot modular chassis with 11 slots for switching modules, and 2 slots reserved for Supervisor 2 modules only—SFPs1 sold separately).
MDS 9513 Switch only
DS-C9509
MDS 9509 director, base configuration (9-slot modular chassis includes 7 slots for switching modules and 2 slots for supervisor modules—SFPs sold separately).
MDS 9509 Switch only
DS-C9506
MDS 9506 director (6-slot modular chassis includes 4 slots for switching modules and 2 slots for supervisor modules—SFPs sold separately).
MDS 9506 Switch only
DS-C9222i-K9
MDS 9222i Multiservice Modular Switch (includes 18 4-Gbps Fibre Channel ports and 4 Gigabit Ethernet IP storage services ports, and a modular expansion slot for Cisco MDS 9000 Family Switching and Service modules.)
MDS 9222i Switch only
DS-C9216-K9
MDS 9216 16-port semi-modular fabric switch (includes 16 1-Gbps/2-Gbps Fibre Channel ports, power supply, and expansion slot—SFPs sold separately).
MDS 9216 Switch only
DS-C9216A-K9
MDS 9216A 16-port semi-modular fabric switch (includes 16 1-Gbps/2-Gbps Fibre Channel ports, power supply, and expansion slot—SFPs sold separately).
MDS 9216A Switch only
DS-C9216i-K9
MDS 9216i 16-port semi-modular fabric switch (includes 14 1-Gbps/2-Gbps Fibre Channel ports, 2 Gigabit Ethernet ports, power supply, and expansion slot—SFPs sold separately).
MDS 9216i Switch only
DS-C9140-K9
MDS 9140 fixed configuration (non-modular) fabric switch (includes 8 full rate ports and 32 host-optimized ports).
MDS 9140 Switch only
DS-C9124-K9
MDS 9124 fixed configuration (non-modular) multilayer fabric switch (includes 8 enabled ports; an on-demand ports activation license can enable 8 additional ports, up to 24 ports).
MDS 9124 Switch only
DS-C9134-K9
MDS 9134 fixed configuration (non-modular) multilayer fabric switch (includes 24 enabled 4-Gbps ports; an on-demand ports activation license can enable 8 additional ports, up to 32 4-Gbps ports. An additional port activation license can enable 2 10-Gbps ports.).
MDS 9134 Switch only
DS-C9120-K9
MDS 9120 fixed configuration, non-modular, fabric switch (includes4 full rate ports and 16 host-optimized ports).
MDS 9120 Switch only
DS-HP-FC-K9
Cisco Fabric Switch for HP c-Class BladeSystem (includes sixteen internal and eight external active ports and four 4-Gb SFPs installed, or eight internal and four external active ports and two 4-Gb SFPs installed).
Cisco Fabric Switch for HP c-Class BladeSystem only
DS-IBM-FC-K9
Cisco Fabric Switch for IBM BladeCenter (includes fourteen internal and six external ports)
Cisco Fabric Switch for IBM BladeCenter only
External crossbar module
DS-13SLT-FAB1
MDS 9513 crossbar fabric module.
MDS 9513 Switch only
Supervisor modules
DS-X9530-SF2-K9
MDS 9500 Supervisor-2, module.
MDS 9500 Series only
DS-X9530-SF1-K9
MDS 9500 Supervisor/Fabric-I module.
Switching modules
DS-X9016
MDS 9000 16-port 1-Gbps/2-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series
DS-X9032
MDS 9000 32-port 1-Gbps/2-Gbps Fibre Channel module (SFPs sold separately).
DS-X9112
MDS 9000 12-port 4-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X9124
MDS 9000 24-port 4-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X9148
MDS 9000 48-port 4-Gbps Fibre Channel module (SFPs sold separately).
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X9704
MDS 9000 4-port 10-Gbps Fibre Channel module (SFPs sold separately)
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
Services modules
DS-X9308-SMIP
8-port Gigabit Ethernet IP Storage services module.
MDS 9500 Series and 9200 Series
DS-X9304-SMIP
4-port Gigabit Ethernet IP Storage services module.
DS-X9032-SSM
MDS 9000 32-port 1-Gbps/2-Gbps Fibre Channel Storage Services Module (SSM).
DS-X9302-14K9
14-port Fibre Channel/2-port Gigabit Ethernet Multiprotocol Services (MPS-14/2) module.
DS-X9304-18K9
18-port Fibre Channel/4-port Gigabit Ethernet Multiservice (MSM-18/4) module.
DS-X9304-18FK9
18-port Fibre Channel/4-port Gigabit Ethernet Multiservice FIPS (MSFM-18/4) module.
Optics
DS-X2-FC10G-SR
X2/SC optics, 10-Gbps Fibre Channel for Short Reach.
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-X2-FC10G-LR
X2/SC optics, 10-Gbps Fibre Channel for Long Reach.
DS-X2-FC10G-ER
X2/SC optics, 10-Gbps Fibre Channel for Extended Reach (40 km).
DS-X2-E10G-SR
X2/SC optics, 10-Gbps Ethernet for Short Reach
DS-X2-FC10G_CX4
X2/CX-4 optics, 10-Gbps Fibre Channel, copper
LC-type fiber-optic SFP
DS-SFP-FC-2G-SW
2-Gbps/1-Gbps Fibre Channel—short wavelength SFP.
MDS 9000 Family
DS-SFP-FC-2G-LW
2-Gbps/1-Gbps Fibre Channel—long wavelength SFP.
DS-SFP-FCGE-SW
1-Gbps Ethernet and 1-Gbps/2-Gbps Fibre Channel—short wavelength SFP.
DS-SFP-FCGE-LW
1-Gbps Ethernet and 1-Gbps/2-Gbps Fibre Channel—long wavelength SFP.
DS-SFP-GE-T
1-Gbps Ethernet SFP.
DS-SFP-FC4G-SW
4-Gbps/2-Gbps/1-Gbps Fibre Channel—short wavelength SFP for DS-X91xx switching modules.
MDS 9500 Series and 9200 Series, except for the MDS 9216 Switch
DS-SFP-FC4G-MR
4-Gbps/2-Gbps/1-Gbps Fibre Channel—long wavelength SFP for DS-X91xx switching modules only. Supports distances up to 4 km.
DS-SFP-FC4G-LW
4-Gbps/2-Gbps/1-Gbps Fibre Channel—long wavelength SFP for DS-X91xx switching modules only. Supports distances up to 10 km.
CWDM2
DS-CWDM-xxxx
Gigabit Ethernet and 1-Gbps/2-Gbps/4-Gbps Fibre Channel SFP LC interface xxxx nm, where xxxx = 1470, 1490, 1510, 1530, 1550, 1570, 1590, or 1610 nm.
MDS 9000 Family
DS-CWDM-MUX-4
Add/drop multiplexer for four CWDM wavelengths.
DS-CWDM-MUX-8
Add/drop multiplexer for eight CWDM wavelengths.
DS-CWDMCHASSIS
Two slot chassis for CWDM add/drop multiplexers.
Power supplies
DS-CAC-6000W
6000-W AC power supply.
MDS 9513 only
DS-CAC-2500W
2500-W AC power supply.
MDS 9509 only
DS-CDC-2500W
2500-W DC power supply.
DS-CAC-3000W
3000-W AC power supply.
DS-CAC-4000W-US
4000-W AC power supply for US (cable attached).
DS-CAC-4000W-INT
4000-W AC power supply international (cable attached).
DS-CAC-1900W
1900-W AC power supply.
MDS 9506 only
DS-CDC-1900W
1900-W DC power supply.
DS-CAC-845W
845-W AC power supply.
MDS 9200 Series only
DS-CAC-300W
300-W3 AC power supply.
MDS 9100 Series only
CompactFlash
MEM-MDS-FLD51M
MDS 9500 supervisor CompactFlash disk, 512 MB.
MDS 9500 Series only
Port analyzer adapter
DS-PAA-2, DS-PAA
A standalone Fibre Channel-to-Ethernet adapter that allows for simple, transparent analysis of Fibre Channel traffic in a switched fabric.
MDS 9000 Family
CD-ROM
M90FMK9-CD322=
MDS 9000 Management Software and Documentation CD-ROM, spare.
MDS 9000 Family
1 SFP = small form-factor pluggable
2 CWDM = coarse wavelength division multiplexing
3 W = Watt
Software Download Process
Use the software download procedure to upgrade to a later version, or downgrade to an earlier version, of an operating system. This section describes the software download process for the Cisco MDS SAN-OS and includes the following topics:
•
•
•
•
Determining the Software Version
To determine the version of Cisco MDS SAN-OS software currently running on a Cisco MDS 9000 Family switch using the CLI, log in to the switch and enter the show version EXEC command.
To determine the version of Cisco MDS SAN-OS software currently running on a Cisco MDS 9000 Family switch using the Fabric Manager, view the Switches tab in the Information pane, locate the switch using the IP address, logical name, or WWN, and check its version in the Release column.
Note
Downloading Software
The Cisco MDS SAN-OS software is designed for mission-critical high availability environments. To realize the benefits of nondisruptive upgrades on the Cisco MDS 9500 Directors, we highly recommend that you install dual supervisor modules.
To download the latest Cisco MDS SAN-OS software, access the Software Center at this URL:
http://www.cisco.com/public/sw-center
See the following sections in this release note for details on how you can nondisruptively upgrade your Cisco MDS 9000 switch. Issuing the install all command from the CLI, or using Fabric Manager to perform the downgrade, enables the compatibility check. The check indicates if the upgrade can happen nondisruptively or disruptively depending on the current configuration of your switch and the reason.
Compatibility check is done:Module bootable Impact Install-type Reason------ -------- -------------- ------------ ------1 yes non-disruptive rolling2 yes disruptive rolling Hitless upgrade is not supported3 yes disruptive rolling Hitless upgrade is not supported4 yes non-disruptive rolling5 yes non-disruptive reset6 yes non-disruptive resetAt a minimum, you need to disable the default device alias distribution feature using the no device-alias distribute command in global configuration mode. The show incompatibility system bootflash:1.3(x)_filename command determines which additional features need to be disabled.
Note
Note
Selecting the Correct Software Image for an MDS 9100 Series Switch
The system and kickstart image that you use for an MDS 9100 series switch depends on which switch you use, as shown in Table 2.
Selecting the Correct Software Image for an MDS 9200 Series Switch
The system and kickstart image that you use for an MDS 9200 series switch depends on which switch you use, as shown in Table 3.
Table 3 Software Images for MDS 9200 Series Switches
MDS 9222i
Filename begins with m9200-s2ek9
MDS 9216A or MDS 9216i
Filename begins with m9200-ek9
Selecting the Correct Software Image for an MDS 9500 Series Switch
The system and kickstart image that you use for an MDS 9500 Series switch depends on whether the switch is based on a Supervisor-1 module or a Supervisor-2 module, as shown in Table 4.
Use the show module command to display the type of supervisor module in the switch. For a Supervisor-1 module, the output might look like this:
switch# show moduleMod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------......5 0 Supervisor/Fabric-1 DS-X9530-SF1-K9 active*6 0 Supervisor/Fabric-1 DS-X9530-SF1-K9 ha-standbyFor a Supervisor-2 module, the output might look like this:
switch# show moduleMod Ports Module-Type Model Status--- ----- -------------------------------- ------------------ ------------......7 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 active *8 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 ha-standbyMigrating from Supervisor-1 Modules to Supervisor-2 Modules
As of Cisco MDS SAN-OS Release 3.0(1), the Cisco MDS 9509 and 9506 Directors support both Supervisor-1 and Supervisor-2 modules. Supervisor-1 and Supervisor-2 modules cannot be installed in the same switch, except during migration. Both the active and standby supervisor modules must be of the same type, either Supervisor-1 or Supervisor-2 modules. For Cisco MDS 9513 Directors, both supervisor modules must be Supervisor-2 modules.
Caution
Note
To migrate from a Supervisor-1 module to a Supervisor-2 module, refer to the step-by-step instructions in the Cisco MDS 9000 Family CLI Configuration Guide.
Configuring Generation 2 Switching Modules
The Cisco MDS 9500 Multilayer Directors are designed to operate with any combination of Cisco MDS 9000 Generation 1 and Generation 2 modules. However, there are limitations to consider when combining the various modules and supervisors in the Cisco MDS 9500 Series platform chassis. The references listed in this section provide specific information about configurations that combine different modules and supervisors.
For information on configuring Generation 2 switching modules, refer to:
http://www.cisco.com/en/US/products/ps5989/products_configuration_guide_chapter09186a0080664c6b.html
For information on port index availability, refer to:
http://www.cisco.com/en/US/products/ps5990/products_installation_guide_chapter09186a0080419599.html
For information on Cisco MDS 9000 hardware and software compatibility, refer to:
http://www.cisco.com/en/US/products/ps5989/products_device_support_table09186a00805037ee.html
Upgrading Your Cisco MDS SAN-OS Software Image
This section lists the guidelines recommended for upgrading your Cisco MDS SAN-OS software image and contains the following sections:
•
•
•
•
•
•
Upgrading Your Version of Cisco Fabric Manager
As of Cisco SAN-OS Release 3.2(1), Cisco Fabric Manager is no longer packaged with a Cisco MDS 9000
Family switch. It is included on the CD-ROM that ships with the switch. You can install Fabric Manager from the CD-ROM or from files that you download.
Installing Cisco Fabric Manager is a multi-step process that involves installing a database, as well as Fabric Manager. The complete installation instructions are provided in the "Installation of Cisco MDS SAN-OS and Fabric Manager" section in the Cisco MDS 9000 Family Fabric Manager Configuration Guide, and are available on-screen once you launch the Fabric Manager installer from the CD-ROM.
The following section presents the flow of the installation process at a high level. Review these guidelines before you begin the installation process.
1.
•
•
•
•
–
–
•
•
•
•
Note
•
•
•
•
•
•
•
•
•
2.
If you are upgrading Cisco Fabric Manager in Cisco SAN-OS Releases 3.1(2b) and later, be aware that data is migrated from the Hypersonic HSQL database to either the PostgreSQL database or Oracle Database 10g Express during the installation. Data is also migrated from Oracle Database 10g Express to Oracle Database 10g Express. If you migrate the database from Oracle to Oracle, the schema is updated.3.
If you are upgrading Fabric Manager in a Cisco SAN-OS Release prior to 3.1(2b), be aware that data is migrated from the Hypersonic HSQL database to either the PostgreSQL database or the Oracle Database 10g Express during the installation. The Fabric Manager Installer installs the PostgreSQL database on Windows. If you want to install the PostgreSQL database on Solaris or Linux, or if you want to install the Oracle Database 10g Express database, follow the instructions in the "Installation of Cisco MDS SAN-OS and Fabric Manager" section in the Cisco MDS 9000 Family Fabric Manager Configuration Guide.
Note
4.
If you want to use the Oracle Database 10g Express, you must install the database and create a user name and password before continuing with the Fabric Manager installation. We recommend the Oracle Database 10g Express option for all users who are running Performance Manager on large fabrics (1000 or more end devices).
If you want to install the PostgreSQL database, you must disable any security software you are running as PostgreSQL may not install certain folders or users. You must also log in as a Superuser before you start the installation.
5.
http://cisco.com/cgi-bin/tablebuild.pl/mds-fm
To install Fabric Manager on Solaris, follow these steps:
Step 1
Step 2
Step 3
Step 4
java -Xms512m -Xmx512m -jar m9000-fm-3.2.3a.jar
Step 5
To install Fabric Manager on Windows, follow these steps:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
To install Device Manager on your workstation, follow these steps:
Step 1
Step 2
Step 3
Step 4
Note
General Upgrading Guidelines
Use the following guidelines when upgrading to Cisco MDS SAN-OS Release 3.2(3a):
•
•
•
•
•
–
–
–
–
–
Use Table 5 to determine your nondisruptive upgrade path to Cisco SAN-OS Release 3.2(3a). Find the image release number you are currently using in the Current column of the table and use the path recommended.
Note
Use Table 6 to determine your FICON nondisruptive upgrade path to Cisco MDS SAN-OS Release 3.2(3a). Find the image release number you are currently using in the Current Release with FICON Enabled column of the table and use the path recommended.
Upgrading with IVR Enabled
An Inter-Switch Link (ISL) flap resulting in fabric segmentation or a merge during or after an upgrade from Cisco MDS SAN-OS Release 2.0(x) to a later image where IVR is enabled might be disruptive. Some possible scenarios include the following:
•
•
•
If this problem occurs, syslogs indicate a failure and the flapped ISL could remain in a down state because of a domain overlap.
This issue was resolved in Cisco SAN-OS Release 2.1(2b); you must upgrade to Release 2.1(2b) before upgrading to Release 3.2(3a). An upgrade from Cisco SAN-OS Releases 2.1(1a), 2.1(1b), or 2.1(2a) to Release 2.1(2b) when IVR is enabled requires that you follow the procedure below, and then follow the upgrade guidelines listed in the "Upgrading Your Version of Cisco Fabric Manager" section. If you have VSANs in interop mode 2 or 3, you must issue an IVR refresh for those VSANs.
To upgrade from Cisco SAN-OS Releases 2.1(1a), 2.1(1b), or 2.1(2a) to Release 2.1(2b) for all other VSANs with IVR enabled, follow these steps:
Step 1
Note
Step 2
Note
Step 3
2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED:%$VSAN 2005%$ Isolation of interfaceport-channel 52 (reason: unknown failure)2005 Aug 31 21:52:04 switch %FCDOMAIN-2-EPORT_ISOLATED: %$VSAN 2005%$Isolation of interface port-channel 51(reason: domain ID assignment failure)Step 4
switch(config)# vsan databaseswitch(config-vsan-db)# vsan vsan-id suspendswitch(config-vsan-db)# no vsan vsan-id suspendStep 5
Step 6
Step 7
Note
Reconfiguring SSM Ports Before Upgrading to SAN-OS Release 3.2(3a)
Starting with Cisco MDS SAN-OS Release 3.0(1), the SSM front panel ports can no longer be configured in auto mode, which is the default for releases prior to Release 3.0(1).
Note
For more information on upgrading SAN-OS software, see the "Upgrading Your Cisco MDS SAN-OS Software Image" section.
If the configuration is not updated before the upgrade, the installation process for the new image will automatically convert all ports configured in auto mode to Fx mode. This change in mode might cause a disruption if the port is currently operating in E mode.
To upgrade the image on your SSM without any traffic disruption, follow these steps:
Step 1
switch# show interface fc 2/1 - 32fc2/1 is upHardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)Port WWN is 20:4b:00:0d:ec:09:3c:00Admin port mode is auto <-------- shows port is configured in auto modesnmp traps are enabledPort mode is F, FCID is 0xef0300 <-------- shows current port operational mode is FPort vsan is 1Speed is 2 GbpsTransmit B2B Credit is 3Step 2
a.
switch# config tswitch(config)# interface fc 2/1switch(config-if)# switchport mode fxb.
switch# config tswitch(config)# interface fc 2/5switch(config-if)# switchport mode eStep 3
a.
switch# config tswitch(config)# interface fc 2/2switch(config-if)# switchport mode fxb.
switch# config tswitch(config)# interface fc 2/2switch(config-if)# shutdownswitch# copy running-config startup-configUpgrading the SSI Image on Your SSM
Use the following guidelines to nondisruptively upgrade the SSI image on your SSM:
•
•
–
–
–
–
–
Caution
Upgrading a Switch with Insufficient Space for Two Images on the Bootflash
To upgrade the SAN-OS image on a Cisco MDS 9000 Family switch requires enough space on the internal CompactFlash (also referred to as bootflash) to accommodate both the old software image and the new software image.
As of Cisco MDS SAN-OS Release 3.1(1), on MDS switches with a 256-MB CompactFlash, it is possible in some scenarios that a user might be unable to fit two images on the bootflash. This lack of space on the bootflash might cause the upgrade process to fail because new images are always copied onto the bootflash during an upgrade.
The following MDS switches are affected by this issue:
•
•
•
To work around an image upgrade failure caused by a lack of space on the bootflash, follow these steps:
Step 1
Step 2
switch# delete bootflash:m9200-ek9-mz.3.0.3.bin
Note
switch# delete bootflash://sup-standby/m9500-sf1ek9-mz.3.0.3.binStep 3
Step 4
Step 5
Upgrading a Cisco MDS 9124 Switch
If you are upgrading from Cisco MDS SAN-OS Release 3.1(1) to Cisco SAN-OS Release 3.2(3a) on a Cisco MDS 9124 Switch, follow these guidelines:
•
•
•
•
•
•
Performing a Disruptive Upgrade on a Single Supervisor MDS Family Switch
Cisco MDS SAN-OS software upgrades are disruptive on the following single supervisor Cisco MDS Family switches:
•
•
•
If you are performing an upgrade on one of those switches, you should follow the nondisruptive upgrade path shown in Table 5, even though the upgrade is disruptive. Following the nondisruptive upgrade path ensures that the binary startup configuration remains intact.
If you do not follow the upgrade path, (for example, you upgrade directly from SAN-OS Release 2.1(2) or earlier version to SAN-OS Release 3.2(3a)), the binary startup configuration is deleted because it is not compatible with the new image, and the ASCII startup configuration file is applied when the switch comes up with the new upgraded image. When the ASCII startup configuration file is applied, there may be errors. Because of this, we recommend that you follow the nondisruptive upgrade path.
Downgrading Your Cisco MDS SAN-OS Software Image
This section lists the guidelines recommended for downgrading your Cisco MDS SAN-OS software image and contains the following sections:
•
•
General Downgrading Guidelines
Use the following guidelines to nondisruptively downgrade your Cisco MDS SAN-OS Release 3.2(3a):
•
•
•
•
•
•
–
–
–
–
–
–
Use Table 7 to determine the nondisruptive downgrade path from Cisco SAN-OS Release 3.2(3a). Find the SAN-OS image you want to downgrade to in the To SAN-OS Release column of the table and use the path recommended.
Note
Use Table 8 to determine your nondisruptive downgrade path, if you have FICON enabled, from Cisco SAN-OS Release 3.2(3a). Find the image release number you are currently using in the Current Release with FICON Enabled column of the table and use the path recommended.
Downgrading the SSI Image on Your SSM
Use the following guidelines when downgrading your SSI image on your SSM.
•
•
•
•
–
–
–
New Features in Cisco MDS SAN-OS Release 3.2(3a)
This section briefly describes the new features introduced in this release. For detailed information about the features listed, refer to the Cisco MDS 9000 Family CLI Configuration Guide, the Cisco MDS 9000 Family Fabric Manager Configuration Guide, and the Cisco MDS 9000 Family Storage Media Encryption Configuration Guide. For information about new CLI commands associated with these features, refer to the Cisco MDS 9000 Family Command Reference. The "New and Changed Information" section in each of these books provides a detailed list of all new features and includes links to the feature description or new command.
Note
There are no new features available for this release.
Limitations and Restrictions
There are no limitations or restrictions for this release.
Caveats
This section lists the open and resolved caveats for this release. Use Table 9 to determine the status of a particular caveat. In the table, "O" indicates an open caveat and "R" indicates a resolved caveat.
Resolved Caveats
•
Symptom: Cisco MDS 9000 Family switches that are running SAN-OS Release 3.1(x) or Release 3.2(x) may display corrupt memory when the show cfs internal message-context <app-name> command is issued. This is seen only on MDS 9000 Family switches that are running SAN-OS Release 3.1(x) or Release 3.2(x) when a CFS-enabled application is processing more than one distribution at a time in a fabric with more than one switch.
Workaround: This issue is resolved.
•
Symptom: When portchannels are up, Fabric Manager Client shows some portchannels as down. When highlighted, the portchannel tooltip shows "vsanInactive".
Workaround: This issue is resolved.
•
Symptom: In rare instances, when a SCSI I/O is in progress in Cisco SME and it is aborted by the host, the Cisco SME interface may fail and a reset may occur.
Workaround: This issue is resolved.
•
Symotom: When the Fabric Manager server is upgraded from SAN-OS Release 3.2.1a or Release 3.2.1b to Release 3.2.2c or Release 3.2.3, the upgrade.sql script is not executed. In this case, the database table will not be shown.
Workaround: This issue is resolved.
•
Symptom: Manually purging the keys in SME integrated with the RSA Key Manager Vault, causes the key lookup to fail and timeout. This prevents the tapes from being recycled.
Workaround: This issue is resolved.
•
Symptom: Fabric Manager sometimes fails discovering the device alias.
Workaround: This issue is resolved.
•
Symptom: After upgrading multiple MDS 9000 Family switches from SANOS Releasle 3.1.3a to Release 3.2.3, and while running IVR NAT, Fibre Channel name server (FCNS) entries may not appear in the transit VSANs. This may stop the FCNS service. If this occurs, the following messages will be displayed:
%SYSMGR-3-HEARTBEAT_FAILURE: Service "fcns" sent SIGABRT for not setting heartbeat for last 5 periods
%SYSMGR-3-SERVICE_CRASHED: Service "fcns" (PID 1649) hasn't caught signal 6 (core saved).Workaround: This issue is resolved.
•
Symptom: Fabric Manager discovers fabrics correctly; however, the display pane shows inconsistencies and missing elements (for example, missing devices, links between devices, and so on). This occurs only when there are EMC FICON adapters present in the fabric.
Workaround: This issue is resolved.
•
Symptom: When a SCSI status frame to the host is lost, with FCP sequence error recovery procedures enabled, causes the encryption engine in the MSM-18/4 module to reset.
Workaround: This issue is resolved.
Open Caveats
•
Symptom: If you bring up more than one link at a time between two VSANs that have overlapping domains and at least one of the switches is SDV enabled, one link will become isolated. The other links will come up, even though the domains are overlapping. In addition, the SDV virtual domains will change, causing traffic disruption on all devices associated with their old value.
Workaround: Bring up multiple links between two switches one at a time. Verify that the first link came up correctly before attempting to bring up the next link. If the first link fails to come up because of a domain ID overlap, resolve the domain conflict and then try again to bring up the links.
•
Symptom: FCIP links may fail on an MDS 9216i switch that has compression set to auto when the other end of the FCIP link is terminated by an IPS-8 module. You may see the following message in the logs:
%IPS_SB_MGR-SLOT1-3-CRYPTO_FAILURE: Heartbeat failure in encryption engine (error 0x1)
%ETHPORT-5-IF_DOWN_SOFTWARE_FAILURE: Interface GigabitEthernet1/1 is down (Port software failure)
%PORT-5-IF_DOWN_SOFTWARE_FAILURE: %$VSAN 1%$ Interface fcip99 is down (Port software failure)Workaround: If both ends of an FCIP link are not on an MPS-14/2 module, do not use mode 1 and auto.
•
Symptom: A data path processor (DPP) might fail on an MDS switch running SSI Release 3.2(1) on the SSM. The failure occurs after several days of running traffic when a misbehaving target sends unexpected frames well after the response has already been received from the same target.
Workaround: None.
•
Symptom: If there is a request to export a domain while the same domain is being cleaned up, domain entries might not be programmed. As a result, communication between IVR devices might not occur.
Workaround: Because the the programming request was lost, the only way to retrigger the programming is to withdraw the domain and refresh IVR. Follow these steps:
1.
switch#show ivr internal dep
Internal information for DEP FSM
--------------------------------
vsan domain nh status sync_status req i/f
101 0x61(97) 1001 ALL_DONE OXID|FCID_RW 0 [ fc3/2 ]
102 0x62(98) 1002 ALL_DONE OXID|FCID_RW 0 [ fc3/5 ]
1001 0x9e(158) 101 NONE OXID|FCID_RW 0 [ fc2/16 ]
1002 0x98(152) 102 ALL_DONE OXID|FCID_RW 0 [ fc9/10]
Number of DEP entries : 4After waiting for a few minutes for IVR to stabilize, if the status column for the {vsan, domain} combination is NONE, then this problem has occurred the switch.
2.
3.
•
Symptom: In rare cases, an FCIP link might flap on a network with high latency and a consistently high loss rate.
Workaround: None.
•
Symptom: When IVR exports a new virtual domain and multiple border switches export that virtual domain, some of the entries in the Fibre Channel name server (FCNS) database that correspond to this virtual domain may have partial entries where the port type contains a dash (-). This can then lead to a lack of IVR communication between these devices and other IVR devices.
Workaround: Use the show ivr internal vdri vsan vsan-id domain domain command to determine which border switch is exporting the virtual domain. Then on any of the border switches that is exporting the virtual domain, enter the following command for each device that has a partial FCNS entry:
switch(config)#ivr device pwwn pwwn fcns register vsan vsan-idIn this example, pWWN is the port pWWN of the device and vsan-id is the VSAN that contains the incomplete FCNS entries.
•
Symptom: Following an upgrade to Cisco MDS SAN-OS Release 3.2(1) on a Cisco MDS 9124 switch, an interface is shown as up, but there is no FLOGI information for the port in the FLOGI database.
Workaround: Set the port mode to F.
•
Symptom: In rare cases, if two or more catastrophic exceptions affecting the MDS arbiter occur in quick succession, it is possible that an MDS 9500 Series switch will completely reset.
Workaround: None.
•
Symptom: The CIM server stops. This occurs after creating a subscription using the same filter and handler.
Workaround: Reload the switch.
•
Symptom: Using Fabric Manager Release 3.2(2), if you have an enclosure with multiple ports and you then use the Data Migration Wizard to create a job with that enclosure as the existing storage but don't select all the storage ports in the enclosure, an error is displayed in the creation wizard.
Workaround: Put the ports you plan to use as the existing storage in the migration into a separate enclosure, and use that enclosure in the wizard selection.
•
Symptom: When you configure Cisco Traffic Analyzer to capture traffic on one or more interfaces on a Windows platform, the configuration web page might not show that the interface has been selected for traffic capture even though traffic capture on that interface is enabled.
Workaround: Check the logs to clarify that the correct interface has been selected.
•
Symptom: If there are IP over Fibre Channel (IPFC) interfaces configured on an SSM, you might experience issues if you downgrade from SAN-OS Release 3.x to Release 2.x.
Workaround: Before downgrading, remove the IPFC interface on the module and then recreate the IPFC interface after the downgrade is complete.
•
Symptom: If IP ACLs are applied to any IP Storage Gigabit Ethernet port, implicit deny does not take effect.
Workaround: Configure explicit deny on the port.
•
Symptom: Time zone changes that are executed on an MDS switch do not take effect on the 12-port, 24-port, and 48 port 1-Gbps/2-Gbps/4-Gbps Fibre Channel modules, and on the 4-port 10-Gbps module. This issue occurs in SAN-OS Releases 3.0(1), 3.0(2), 3.0(2a), and 3.0(3).
Time zone changes that are executed on an MDS switch do not take effect on the 16-port or 32-port 1-Gbps/2-Gbps module, on the 4-port or 8-port Gigabit Ethernet IP services module, the MPS-14/2 module, and on the SSM. This issue occurs in SAN-OS Release 3.0(3).
This issue has no effect on functionality. However, debug messages and syslogs from the MDS switching modules have incorrect timestamps if the time zone is configured on an MDS switch.
Workaround: None.
•
Symptom: Graceful shutdowns of ISLs are not supported for IVR traffic.
Workaround: Increase the FSPF cost on the link before it is shut down, so that traffic will flow through an alternate path.
•
Symptom: The management port on MDS switches supports one user-configured IPv6 address, but does not support autoconfiguration of an IPv6 address in Cisco SAN-OS Release 3.2(1).
Workaround: None.
•
Symptom: On a Gigabit Ethernet interface on an MDS MSM-18/4 module, shut the interface before removing its IP address so that configuration changes on the interface can take effect. This applies only to the Gigabit Ethernet ports in slot 1 of the MDS 9222i switch and the MDS 9216i switch.
Workaround: Always shut the interface using the shutdown command before removing the IP address and making configuration changes.
•
Symptom: In certain conditions, an MDS switch may not be able to determine the FC4-type of certain targets. This causes the targets to be listed in the hosts section during a Cisco SME tape group or tape device configuration.
Workaround: Issue the discover scsi-target vsan vsan-id fcid fcid command to re-discover the FC4-type of the targets. A Cisco SME tape group or tape device configuration will now list the targets correctly.
•
Symptom: HP Blade Servers that are connected through an HP Virtual Connect (VC) FC module to a Cisco Fabric Switch for HP c-Class BladeSystem using NPIV lose access to LUNs when load balancing on the VC module is switched from 16:1 to 8:1. When the load balancing ratio is 16:1, all servers connect through interface ext1. When the ratio is 8:1, servers 1 and 3 connect through ext1, servers 2 and 4 connect through ext2, and so on. Servers on ext2 are not affected by the switchover. In addition, packets might get dropped when the switchover occurs.
Workaround: None.
•
Symptom: In rare situations, on an MDS 9513 director switch, an upgrade fails when a standby supervisor does not come up to a state that the installer recognizes. As a result, the standby supervisor is reloaded to recover and the system runs the older configuration version.
Workaround: Perform the upgrade again.
•
Symptom: Fabric Manager takes 2 to 3 minutes to bring up the DMM job creation wizard in a setup with 25 switches, 400 enclosures, and 2400 entries in the name server.
Workaround: None.
•
Symptom: In a configuration with a PortChannel with FCIP members and write acceleration in use, if IVR NAT is enabled on one end of the PortChannel and not enabled on the other end, then traffic over the FCIP tunnel might fail.
Workaround: Enable IVR NAT on both ends of the PortChannel or disable it on both ends.
•
Symptom: IPv6 duplicate address detection (DAD) may not always works for the management port.
Workaround: None.
•
Symptom: If DMM is provisioned on the SSM and you downgrade to a Cisco MDS SAN-OS release that does not support DMM, the configuration persists and the GUI and CLI show DMM as a provisioned application.
Workaround: Manually remove the DMM configuration from the switch before downgrading to a Cisco MDS SAN-OS release that does not support DMM, such as downgrading from SAN-OS Release 3.2(1) to SAN-OS Release 3.1(3). If you forget to remove the configuration before the downgrade, power off the module and purge the configuration on the SSM module by entering the following commands:
switch(config)#poweroff module slot
switch# purge module slot running-config•
Symptom: If an NASB configuration in a VSAN is destroyed while a target discovery is pending, the NASB process fails. Issue the show nasb vsan x command on the SSM to view the target discovery in the Pending state.
Workaround: Reload the SSM.
•
Symptom: When NASB is enabled in a VSAN, all targets that are visible in that VSAN are discovered by NASB. If a new target is added to the VSAN, NASB does not automatically discover the new target.
Workaround: To discover the new target, reload the SSM or disable and re-enable NASB in the VSAN.
•
Symptom: In rare situations during a storage-based online data migration job, the user might not be able to destroy the job if the following sequence of events occurs:
1.
2.
3.
4.
Workaround: Reload the SSM.
•
Symptom: If you use JDK instead of JRE on Solaris, you might encounter a problem trying to install Device Manager from a web browser. This can happen because the installer heap limit of 256 MB is not sufficient.
Workaround: If you have this problem, save the jnlp link as file, increase the heap limit to 512 MB, and run javaws element-manager.jnlp at the shell prompt.
•
Symptom: After a disruptive downgrade or upgrade between SAN-OS Release 3.2(2c) and Release 3.2(1a), issuing a no shutdown command on a Cisco SME interface fails. When issuing the install all command to perform the downgrade process, a warning is issued that indicates that the downgrade will be disruptive if Cisco SME is enabled.
Workaround: Disable Cisco SME before proceeding with the downgrade process. If you perform a disruptive downgrade, then issue the purge module slot running-config command for the MSM-18/4 modules where Cisco SME is configured after the downgrade is complete.
•
Symptom: On the MDS 12-port, 24-port, and 48-port 4-Gbps Fibre Channel switching modules, and on the 4-port 10-Gbps Fibre Channel switching module for downgrades from 3.2(2c) to lower versions, if fcdomain persistency is disabled, F ports may not come up after a shutdown or no shutdown or a link flap.
Workaround: Shut the F port, enable and disable fcdomain persistency for that VSAN, and then bring up the F port.
•
Symptom: During an MDS 9222i switch reload, the connection from the management port (mgmt0) to the Gigabit Ethernet interface goes down. When the connection comes back up, the Gigabit Ethernet interface doesn't go into forwarding mode until 30 seconds later. The Fabric Manager server is not able to communicate to the MDS 9222i switch through SNMP during this 30 second window.
Workaround: If the switch is in the Cisco Ethernet switch family, configure port-fast to resolve the issue. On Ethernet switches from other vendors, apply a similar configuration mode.
•
Symptom: In DMM, if a server I/O to a LUN fails during data migration, that session is marked as failed. The DMM migration job is then moved to a Failed state when the remaining sessions are complete. Such a failed migration job can be scheduled for a restart. If such a failed migration job is scheduled to start in less than 5 minutes from the time of scheduling, and another server I/O to a session LUN fails in that 5 minute window, the migration job will move from a Scheduled state to a Failed state. An administrator has the option to start the job immediately or schedule it again. This problem does not happen if an administrator schedules the migration job to start more than 5 minutes from the time of scheduling.
Workaround: Schedule the data migration job to start more than 5 minutes from the time of scheduling.
•
Symptom: In Cisco SME, tape device names can not include special characters (such as hyphens or underscores). This will cause future tape device creations for a tape group to fail.
Workaround: Use only alpha-numeric values for tape device names.
•
Symptom: Dual-fabric DMM migration jobs can not have one fabric running Release 3.2(1a) and a peer fabric running Release 3.2(2c) due to a signal message change. This may cause unexpected results during a DMM migration job validation, creation, start, and so on.
Workaround: Run both fabrics with the same software image.
•
Symptom: Using Fabric Manager Release 3.2(2), an error is displayed in the creation wizard. This occurs when an enclosure spans multiple fabrics and not all fabrics are managed and when the Data Migration Wizard is used to create a job with that enclosure as the existing storage (selecting all ports listed in that enclosure).
Workaround: Put the ports you plan to use as the existing storage in the migration into a separate enclosure, and use that enclosure in the wizard selection.
•
Symptom: The response time shown in the output of a ping ip-address command may not be accurate if there is an MDS MSM-8/4 in the path.
Workaround: Use the ips measure-rtt command to measure the round trip time.
•
Symptom: When you issue the show tech-support sme or the show klm internal isapi_scsi command after attaching to a module, you may see this error message:
cat: write error: Bad address. This issue does not affect the actual tech-support log.Workaround: None.
•
Symptom: In certain tape libraries, the tape drives are exported as LUNs. If these target ports are already a part of a Cisco SME configuration and new tape drives are added as LUNs, the new tape drives will not be discovered during a Cisco SME tape group or tape device configuration.
Workaround: Perform a rescan at the host level or a flap of the target port to allow Cisco SME to rediscover these newly added tape drives.
•
Symptom: The following Fabric Manager client components that use SSH and Telnet do not work well with NAT:
•
•
•
Workaround: None.
•
Symptom: The signal loss counters in the output of the show interface fcx/y command are not incremented.
Workaround: None.
•
Symptom: In rare cases, if a READ command issued by Cisco SME for media identification is dropped or lost, the tape is marked as a clear-text tape. Subsequently, a CHECK_CONDITION with ILI is returned when a READ is issued by the host. This can cause a backup application to mark the tape as read-only.
Workaround: Unmount and remount the tape from the backup application to resolve this issue.
•
Symptom: In rare cases, when Cisco SME attempts to perform a tape device discovery of the backend tapes, a SCSI command can stall. This may cause Cisco SME to remain in the device discovery phase.
Workaround: Reload the module.
•
Symptom: There is a observable performance drop for backup and restore when Cisco SME is introduced between a host and tape due to the increased latency.
Workaround: None.
•
Symptom: In certain cases with the Tape Recycle policy enabled in Cisco SME, a new key is generated when a tape is recycled and the old key is not purged.
Workaround: Manually purge the older version of the key.
Related Documentation
The documentation set for the Cisco MDS 9000 Family includes the following documents.
Release Notes
•
•
•
Compatibility Information
•
•
•
•
Regulatory Compliance and Safety Information
•
Hardware Installation
•
•
•
•
Cisco Fabric Manager
•
•
•
•
•
Command-Line Interface
•
•
•
•
•
Troubleshooting and Reference
•
•
•
•
Installation and Configuration Note
•
•
•
•
•
Obtaining Documentation, Obtaining Support, and Security Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0710R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2008 Cisco Systems, Inc. All rights reserved.
Posted: Mon Feb 4 15:01:09 PST 2008
All contents are Copyright © 1992--2008 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
