cc/td/doc/product/rtrmgmt
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Installation and Release Notes for
VPN Device Manager 1.1.1

Installation and Release Notes for
VPN Device Manager 1.1.1

These release and installation notes describe the system requirements, installation instructions, caveats, and other information for Cisco VPN Device Manager 1.1.1 (VDM 1.1.1). All of the features and functionality that were previously available in VDM 1.0 and VDM 1.1 are also available in VDM 1.1.1.

This document contains the following sections:

Introduction to VDM

VPN Device Manager (VDM) software is installed directly onto VPN-enabled Cisco routers. It allows network administrators to manage and configure site-to-site VPNs on a single router from a web browser. VDM implements a wizard-based GUI that allows simplified VPN configuration of the router. VDM requires configuration of some Cisco IOS commands before it can be fully operational. VDM is supported on Cisco IOS releases described in the "System Requirements" section. For information about new features in the VDM 1.1.1 release, see the "New Features" section.

VDM supports site-to-site VPNs. Its step-by-step wizards simplify the configuration of common VPN setups, interfaces, and policies, including:

VDM also monitors general system statistics and VPN-specific information such as tunnel throughput and errors. The graphing capability allows comparison of such parameters as traffic volume, tunnel counts, and system utilization.

Figure 1 shows a simplified VDM deployment.


Figure 1: Simplified VDM Deployment

New Features

VDM release 1.1.1 adds support for the 7400 series router platform. The 7400 series routers are supported on Cisco IOS release 12.2(9)YE or later.

Documentation Roadmap


Note   Although every effort has been made to validate the accuracy of the information in the printed and electronic documentation, you should also review the VDM documentation on Cisco.com for any updates.

Use these publications to learn more about VDM:

Documentation Update

The VDM online help contains some options for clearing active tunnels. In addition to using those options, you can clear all active IPSec and IKE tunnels by clicking the Clear IPSec and IKE Tunnels button in the Clear Active Tunnels dialog box.

Benefits, Requirements, and Features Not Supported

This section contains:

Benefits

Table 1 contains detailed descriptions of VDM benefits.


Table 1: VDM Benefits

Configuration Wizards

VDM browser-based wizards help you perform ordinarily complex setup operations including:

  • Step-by-step instructional panes for simplified VPN configuration such as site-to-site setup

  • Tunneling and encryption support such as:

    • Transform sets

    • IKE policies

    • Pre-shared keys

    • Digital certificates

Convenient Navigation

The following navigation methods ensure that you can identify your current location within each wizard:

  • Highlighted menu tabs at the top of the GUI

  • Step-by-step task list in each wizards's left frame contains a highlighted bar that moves down the list as you progress through that wizard

Monitoring Functions

Monitored data in graphs and charts contains basic router information, a VPN report card, top-ten lists, and detailed views of user-specified tunnels monitoring including:

  • Router health (for example, CPU and RAM utilization)

  • Tunneling, encryption performance, and error rate counts

  • Throughput

No Client Installation

You can run VDM from a browser without installing it on the computer.

Preview of CLI Commands Generated by the Wizards

The View CLI button within the Configure secondary menu enables you to view the exact Cisco IOS CLI commands to be executed after you commit your configuration.

Single Device Configuration

Configures only the router from which VDM is launched. Does not read or write configuration information to or from other routers.

Support for HTTPS Server

Provides the capability to connect to the Cisco IOS HTTPS server securely.

System Requirements

The following sections describe the VDM system requirements:

Supported Hardware

VDM supports the following hardware platforms:

Supported Software

All versions of the VDM client application are compatible with any supported Cisco IOS version. Only Cisco IOS images whose image names contain the strings 'k2' or '56i' support VDM.

Table 2 describes the Cisco IOS versions that support the VDM client.


Table 2: VDM Supported Cisco IOS Versions
Cisco IOS Version Notes

Release 12.1(6)E or later

VDM support was introduced in the 12.1(6)E release.

Release 12.1(11)E or later

VDM was enhanced to provide support for HTTPS connection to the router in the 12.1(11)E release.

Release 12.2(9)YE or later

Memory Requirements

VDM requires 2 MB of available Flash memory on the router.

Browser Requirements

Table 3 contains browser requirements.


Caution   Although VDM might run on any web browser that supports Java and JavaScript, it has been tested only on those listed in this section. It is highly recommended that you use a supported browser. Cisco Systems does not guarantee support for other browsers.


Table 3: VDM Client Requirements
Browser Version JVM1 Platform

Internet Explorer (recommended)

5.0 or later

5.0.0.3309 or later

Windows 2000 with Service Pack 1, Windows NT 4.0 with Service Pack 6a, Windows 98

Navigator

4.7x or later

Windows 2000 with Service Pack 1, Windows NT 4.0 with Service Pack 6a, Windows 98, Solaris 2.6 or Solaris 7

1 JVM=Java Virtual Machine

Features Not Supported

This release of VDM does not support:

Installation and Uninstallation Instructions

To install VDM, follow the instructions in the following sections:

Installing VDM


Note   Effective with Cisco IOS Release 12.1(6)E, all 7100 and 7200 routers can be ordered with VDM preinstalled. If VDM is already installed on your router, go to "Enabling VDM" section.

If VDM is not installed in your router Flash memory, you must do both of the following:

To download and install VDM:


Step 1   Enter http://www.cisco.com/cgi-bin/tablebuild.pl/vdm  in your browser.

Step 2   Click vdm-1.0.tar to download the file and save it on a TFTP or FTP server.

Step 3   Log in to the router directly or use Telnet.

Step 4   Enter enable mode:

Router>enable
Password: xxxxx
Router#

Step 5   Enter the show xsm version command to verify that one of the Cisco IOS releases mentioned in Table 2 is running:

Router>show xsm version

If the appropriate Cisco IOS release is not running, upgrade to the appropriate release.

Step 6   Ensure that the router has at least the minimum required Flash memory (2 MB) by using the directory command to determine the amount of free space, for example:

Router#directory disk0:
Directory of disk0:/

1 -rw- 448893 Jan 03 2000 18:06:17 file01.txt
2 -rw- 213273an 03 2000 18:06:17 file02.txt
20578304 bytes total (19733404 bytes free)

Step 7   Do one of the following:

Router#copy tftp://tftp-host/path_to_vdm-1.0.tar/vdm-1.0.tar disk0:/vdm.tar

where tftp-host is the TFTP server on which vdm-1.0.tar is located, and path_to_vdm-1.0.tar is the directory in which the tar file is located.

Router#copy ftp://ftp-host/path_to_vdm-1.0.tar/vdm-1.0.tar disk0:/vdm.tar

where ftp-host is the FTP server on which vdm-1.0.tar is located, and path_to_vdm-1.0.tar is the directory in which the tar file is located.


Enabling VDM

Before using VDM, you must do the following to enable it:


Step 1   Enter config mode:

Router>enable
Password: xxxxx
Router#configure terminal
Enter configuration commands, one per line. End with CNTL-Z.

Step 2   Do one of the following:

Router(config)#ip http server

Router(config)#ip http secure-server

Router(config)#ip http server
Router(config)#ip http secure-server

Step 3   Enable XSM by entering:

    Router(config)#xsm

Step 4   Enable the XSM history command to track historical VDM statistics by entering:

    Router(config)#xsm history vdm

Step 5   Enable the EDM history command to track embedded router statistics by entering:

    Router(config)#xsm history edm

Step 6   Enable TopN processing by entering (you could specify the processing intervals from 60 to 86400 seconds):

    Router(config)#cry mib topn interval 60

Understanding VDM Privilege Levels

VDM privilege levels control your access to VDM functionality. They control access to VPN configuration information and wizards and are set and changed using XSM privilege commands in the CLI. These commands limit your ability to configure wizards and monitor data only in the VDM GUI. They have no effect on your authorization to configure the router using the CLI. For information about the XSM privilege level commands, see Cisco IOS Commands for VPN Device Manager.

The three privilege levels are:

To confirm that you have the full and unlimited configuration privilege level, the Current User Privilege box (on the VDM home page) displays the following:

Authorized to view configuration and monitor data

With monitor privilege level the Current User Privilege box (on the VDM home page) displays the following:

Monitoring privileges only (monitor users)

Your privilege level status is also displayed in the application status bar when you start VDM. If you attempt a configuration task (for example, a wizard) with a monitor privilege level, a dialog box appears notifying you that you are unauthorized to configure the router.

Unauthorized to use VDM

Starting VDM

This section contains:

Starting VDM in Configuration Mode

The VDM URL defaults to configuration mode (default privilege level 15). At this level, you can start VDM using either the HTTP or the HTTPS server. The following sections provide more information:

Starting VDM in Configuration Mode Using the HTTP Server

To start VDM in configuration mode using the HTTP server, do one of the following:

You can connect to the router using any IP address configured on the router. If your router hostname is in the Domain Name System (DNS), you can use the router name instead. For example, if your DNS hostname is charlie and your domain name is anydomain, enter:

http://charlie.anydomain.com/level/1/go/vdm

Starting VDM in Configuration Mode Using the HTTPS Server

HTTPS is supported on Cisco IOS release 12.1(11)E or later. To start VDM in configuration mode using the HTTPS server, do one of the following:

You can connect to the router using any IP address configured on the router. If your router hostname is in the Domain Name System (DNS), you can use the router name instead. For example, if your DNS hostname is charlie and your domain name is anydomain, enter:

https://charlie.anydomain.com/level/1/go/vdm

The HTTPS server looks for vdm.tar in all Flash filesystems and the VDM application window appears, see Figure 2.


Figure 2: VDM Application Window—Configuration Mode Using HTTPS Server
Number Description

1

Authorization icon in configuration mode—Indicates that you can configure the router, view router configuration, and monitor the router. For more information, see the "Understanding VDM Privilege Levels" section.

2

Security icon—Closed padlock (Figure 2) indicates that VDM is connected to the router through HTTPS. Open padlock indicates that VDM is connected to the router through HTTP.

3

Connection icon—Solid green line indicates that you are connected to the router. Broken red line indicates that you are not connected to the router.

If VDM displays less information in the various VDM windows than you expected, your privilege level might be set too low. For information about setting the appropriate privilege level, see the "Understanding VDM Privilege Levels" section or ask your system administrator for assistance. For more information, see the VDM online help.

Starting VDM in Monitor Mode

If you do not have configuration mode privileges, you will not be able to configure the router from VDM. However, you can still start VDM (for monitoring purposes) by manually entering your privilege level number in the browser. At this level, you can start VDM using either the HTTP or the HTTPS server. The following sections provide more information:

Starting VDM in Monitor Mode Using the HTTP Server

To start VDM in monitor mode using the HTTP server, enter:

http:// router/level/n/go/vdm

For n, enter a number between 0 and 14. If your number is equal to or greater than the configured VDM monitor mode, and less than the configured VDM configuration mode, you can launch VDM in monitor mode. If not, you will be notified that you do not have the correct privilege level.

You can connect to the router using any IP address configured on the router. If your router hostname is in the Domain Name System (DNS), you can use the router name instead. For example, if your DNS hostname is charlie and your domain name is anydomain, enter:

http://charlie.anydomain.com/level/1/go/vdm

Starting VDM in Monitor Mode Using the HTTPS Server

HTTPS is supported on Cisco IOS release 12.1(11)E or later. To start VDM in monitor mode using the HTTPS server, enter:

https://router/level/n/go/vdm

For n, enter a number between 0 and 14. If your number is equal to or greater than the configured VDM monitor mode, and less than the configured VDM configuration mode, you can launch VDM in monitor mode. If not, you will be notified that you do not have the correct privilege level.

You can connect to the router using any IP address configured on the router. If your router hostname is in the Domain Name System (DNS), you can use the router name instead. For example, if your DNS hostname is charlie and your domain name is anydomain, enter:

https://charlie.anydomain.com/level/1/go/vdm

If the HTTPS server finds vdm.tar in the Flash filesystem, it will launch VDM and the VDM application window appears, see Figure 3.


Figure 3: VDM Application Window—Monitor Mode Using HTTPS Server
Number Description

1

Authorization icon in monitor mode—Indicates that you can view monitored router data but you cannot configure the router. For more information, see the "Understanding VDM Privilege Levels" section.


    Note   In Monitor mode, the authorization icon is crossed out with a red "x".

2

Security icon—Closed padlock (Figure 3) indicates that VDM is connected to the router through HTTPS. Open padlock indicates that VDM is connected to the router through HTTP.

3

Connection icon—Solid green line indicates that you are connected to the router. Broken red line indicates that you are not connected to the router.

If VDM displays less information in the various VDM windows than you expected, your privilege level might be set too low. For information about setting the appropriate privilege level, see the "Understanding VDM Privilege Levels" section or ask your system administrator for assistance. For more information, see the VDM online help.

Exiting VDM

There are two ways to exit VDM:

Disabling VDM

To disable VDM, Telnet to the router and enter:

Router>enable
Password:xxxxx
Router#configure terminal
Enter configuration command, one per line. End with CNTL-Z Router#no xsm

This command disables VDM from the router. You can still run VDM from the client but without the ability to collect data. For uninstallation instructions, see "Uninstalling VDM."

Uninstalling VDM

To uninstall VDM, delete the file from the router Flash memory.


Step 1   Telnet to the router and enter:

Router>enable
Password:xxxxx

Step 2   Navigate to disk0: or the directory in which the vdm.tar file is located:

Router#cd disk0:

Step 3   Delete the vdm.tar file using the delete command:

Router#del vdm.tar


Known Problems

Known problems (bugs) in [product] are graded according to severity level. These release notes contain descriptions of:

You can search for problems using the Cisco Software Bug Toolkit. To access the Software Bug Toolkit:


Step 1   Log into Cisco.com.

Step 2   Select Service & Support>Technical Support Help—Cisco TAC>Tool Index.

Step 3   In the Jump to: links at the top of the page, click the letter S, then select Software Bug Toolkit.


You can also access the Software Bug Toolkit by entering the following URL in your web browser:

http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl .

Table 4 describes the problems known to exist in this release; Table 5 describes the problems resolved since the last release of VDM.


Table 4: VPN Device Manager Known Problems
Bug ID Summary Explanation

CSCdv36863

VDM does not work with Navigator 6.0 or later.

Navigator 6.0+ is not yet supported. Please use Navigator 4.7+ or Internet Explorer 5.5+.

CSCdw89882

An exception occurs when VDM is launched with Navigator on Windows 98.

When using VDM with Navigator 4.76 on Windows 98, you might see errors on the status bar and in the system log about duplicate attributes.

No workaround available; exit VDM and restart.

CSCdw62593

Enrollment updates are slow in the certificate wizard.

When you use the certificate enrollment wizard in Navigator 4.76 with an HTTPS connection, you might experience updating delays in each step of the wizard.

No workaround available; simply wait for the next update of VDM (within 10 seconds).

CSCdw59489

Updated data in the table is not sorted correctly on the SystemView: Network Interfaces dialog box.

When viewing the SystemView: Network Interfaces dialog box, you can sort the table by any column. However, after each update, the data is not sorted correctly.

To work around this problem, click on the column header of the data after each update to sort the table again.

CSCdv38482

Sometimes, VDM reports a parser error, then fails fatally.

No workaround available; exit VDM and restart.

CSCdw70703

IPSec Total Throughput chart displays negative values.

Charting the IPSec Total Throughput may intermittently show spikes of negative values.

No workaround available.

CSCdw53247

VDM displays TopN data even though the TopN system is not enabled on the device. VDM provides no way of allowing the user to determine whether TopN has been enabled.

Before viewing TopN data on VDM, enable the TopN system on the device using the following CLI command:

Router(config)#cry mib topn interval 60

This causes the TopN system to be enabled until you explicitly disable it using the following CLI command:

Router(config)#no cry mib topn

CSCdv59589

VDM displays 3DES as a potential transform even though the IOS image might not support 3DES.

Select 3DES as a transform only if your IOS image supports 3DES. 3DES is supported in the "k2" IOS feature set.

CSCdt59899

If you relaunch VDM in the same browser, you might see some exceptions in the Java console.

Before relaunching VDM in the same browser, give the previous VDM application instance enough time to shut down properly. Typically, this is 30 seconds or less. After that, you can relaunch VDM without problems.

CSCdt53856

or

CSCdu06036

Fatal Error (parser): Transform set name with &.

Double quotes (") or ampersands (&) in the Cisco IOS configuration might cause the GUI to log parser errors, such as Error: FATAL ERROR: expected character found "%" expected ";": at <no url>: line 5939 column 19. These characters have special meaning to the XML data stream sent from the router to the GUI, but are not "escaped" by the IOS when converted to XML.

To work around this problem, remove any ampersands or double quotes from the router configuration before running VDM. Check all crypto-map names and descriptions, access list names and comments, peer keys and transform set names.

CSCdt59736

LZ compression should be disabled when router has ISA or ISM in it.

Routers with Integrated Services Adapter (ISA) or Integrated Services Module (ISM) do not support LZ compression.

Transforms with LZ compression selected will fail to commit, and connections that define new transforms with LZ compression will not commit.

To work around this problem, do not specify LZ compression in a transform if your router does not support this feature.

CSCdt66389

java.lang.OutOfMemoryError occurs when charting.

This can occur with more than 6 charts open at once for long periods of time.

To work around this problem, limit your chart usage to six at a time and close any unnecessary charts.

CSCdt68379

GUI should correct subnet/mask incongruencies.

Subnets specified in a connection appear to change once committed, but the packets are correctly selected. The router will mask out bits in the netmask that are used. For example, if the IP address 1.2.3.4 and mask 255.255.255.0 are chosen, the Cisco IOS in the router will record this as 1.2.3.0 with a mask of 255.255.255.0. An address of 1.2.3.4 with a netmask of 0.0.0.0 will be displayed as 'any'.

No workaround available since this is expected behavior.

CSCdt71760

Remove button should not be allowed on unsupported configuration.

A connection might appear in the connection wizard marked with a red-slash-in-a-circle with descriptive text 'on no interface', but if the connection is removed, the commit fails to remove the connection with the error 'crypto map is in use'.

This occurs when a connection is attached to a sub-interface. VDM does not recognize sub-interfaces, and erroneously shows those connections as 'on no interface'.

No workaround available.

CSCdt75160

A pop-up dialog box requesting "level 15" login and password appears when using ping or traceroute under Tools/Test > Connectivity.

Occurs when logged in under monitor mode. The level 15 login and password is erroneously required to use the ping and traceroute facility from the GUI.

There is no workaround available.

CSCdt77038

The Connection wizard suffers delays in recognizing access lists.

Under Configure > Connections, some access lists (ACLs) are not recognized for up to 10 seconds.

To work around this problem, click on a tab to go to another window.

CSCdt80364

Cannot edit a newly created connection after you log in again.

After editing a connection, but before committing it, a dialog box might appear indicating that the connection configuration has changed, and asks if you want to use their new configuration (and discard yours), but no one has changed the configuration.

To work around this problem, choose No to preserve your changes, and commit as usual.

CSCdt91013

VDM: turn on/off xsm history edm through xmlparser exception log.

Turning XSM history on/off while charting causes an exception. The charting tools use historical data from the router and disabling it while the chart is running may cause a problem.

To work around this problem, do not disable XSM history while using the charting tools.

CSCdt95961

Greater than four XSM sessions cause the client to fail to get a connection.

When running four or more simultaneous VDM clients, the last client to connect may fail to connect to the router and does not reconnect, or it appears to connect with a session ID of 0.

To work around this problem, exit and restart VDM on the client with the failed connection or wait until one or more of the other clients has disconnected. The number of active VDM clients can be verified on the router using the show XSM status command.

CSCdu07875

Reload while VDM up exception.

Reloading the router while running VDM causes an exception. VDM occasionally cannot automatically reconnect to the router after it is reloaded and throws an exception. When this happens VDM must be restarted.

CSCdu09119

NullPointerException when exiting VDM.

Closing VDM using the [X] in the window frame instead of Logout might generate an exception.

No workaround available.

CSCdu09191

Log Error: attribute is defined more than once.

The log displays errors involving multiple definitions of attributes. Attributes are defined to hold data from the router. Multiple definitions are harmless.

No workaround is necessary.

CSCdx35977

Diffie-Hellman Group 5 is not supported on low-crypto Cisco IOS images, but is available to select in VDM.

Diffie-Hellman (DH) Group 5 is only available on high-crypto IOS images (feature sets k2 or k9). VDM does not differentiate between low-crypto and high-crypto transforms or DH groups.

If you select DH Group 5 in VDM but the device does not support it, the following happens:

  • An "Invalid input..." error appears in the VDM Commit dialog box, referring to the selection of DH Group 5.

  • DH Group 1 (the default value) is configured on the device, rather than Group 5.

Workaround: Do not select DH Group 5 for your IKE Policies in VDM when running a low-crypto IOS image.

CSCdx72940

The VDM Connection wizard does not warn you if an existing crypto map does not have a transform set assigned to it.

The VDM Connection wizard will not allow you to complete the wizard without selecting at least one transform set.

Workaround: Verify that one or more transform sets are assigned to all crypto maps before attaching them to an interface.

CSCdw46364

Certain digital certificate operations can cause the SSL connection between the client and device to fail when using Internet Explorer.

The SSL connection between a client using Internet Explorer (IE) and the device fails when the device gets a new digital certificate, because IE does not automatically update to use the new SSL certificate from the device. This problem can occur in the following cases:

  • You use the VDM Certificate wizard to generate a new RSA key pair or to delete an existing CA identity.

  • You are using VDM when you or another user generates a new RSA key pair or deletes an existing CA identity using either the VDM Certificate wizard or the CLI.

Workaround: VDM might automatically obtain the device digital certificate. If this happens, a notification will appear and an IE window will open and then close automatically. If VDM does not automatically obtain the device certificate, exit and restart VDM. IE obtains the device digital certificate, restoring SSL connectivity.

CSCdv90035

If you use the Connection wizard to create a new connection, but then you remove (delete) the connection, you can still commit any new transform sets and peers defined in the removed connection.

Workaround: Do not commit the changes. Cancel out of the Connection wizard.

CSCdw85732

Deleting the query URL of an existing CA identity in the Certificate wizard does not work.

Workaround: Delete the entire CA identity, including the query URL, then create a new identity without the query URL.

CSCd


Table 5: VPN Device Manager Resolved Problems
Bug ID Summary Additional Information

CSCdt77127

Single protocol was displayed multiple times.

The same protocol or service is no longer displayed several times in the Description box in the Connection Overview window.

CSCdt51119

Protocol Profile viewing problem: Deny Some with TCP or UDP did not work.

You are now able to select the Deny Some option and the TCP or UDP protocols (without port numbers) in the Connection wizard.

Obtaining Documentation

The following sections explain how to obtain documentation from Cisco Systems.

World Wide Web

You can access the most current Cisco documentation on the World Wide Web at the following URL:

http://www.cisco.com

Translated documentation is available at the following URL:

http://www.cisco.com/public/countries_languages.shtml

Ordering Documentation

Cisco documentation is available in the following ways:

http://www.cisco.com/cgi-bin/order/order_root.pl

http://www.cisco.com/go/subscription

Documentation Feedback

If you are reading Cisco product documentation on Cisco.com, you can submit technical comments electronically. Click Feedback at the top of the Cisco Documentation home page. After you complete the form, print it out and fax it to Cisco at 408 527-0730.

You can e-mail your comments to bug-doc@cisco.com.

To submit your comments by mail, use the response card behind the front cover of your document, or write to the following address:

Cisco Systems
Attn: Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools by using the Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC Web Site.

Cisco.com

Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.

Cisco.com is a highly integrated Internet application and a powerful, easy-to-use tool that provides a broad range of features and services to help you to

You can self-register on Cisco.com to obtain customized information and service. To access Cisco.com, go to the following URL:

http://www.cisco.com

Technical Assistance Center

The Cisco TAC is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two types of support are available through the Cisco TAC: the Cisco TAC Web Site and the Cisco TAC Escalation Center.

Inquiries to Cisco TAC are categorized according to the urgency of the issue:

Which Cisco TAC resource you choose is based on the priority of the problem and the conditions of service contracts, when applicable.

Cisco TAC Web Site

The Cisco TAC Web Site allows you to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC Web Site, go to the following URL:

http://www.cisco.com/tac

All customers, partners, and resellers who have a valid Cisco services contract have complete access to the technical support resources on the Cisco TAC Web Site. The Cisco TAC Web Site requires a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to the following URL to register:

http://www.cisco.com/register/

If you cannot resolve your technical issues by using the Cisco TAC Web Site, and you are a Cisco.com registered user, you can open a case online by using the TAC Case Open tool at the following URL:

http://www.cisco.com/tac/caseopen

If you have Internet access, it is recommended that you open P3 and P4 cases through the Cisco TAC Web Site.

Cisco TAC Escalation Center

The Cisco TAC Escalation Center addresses issues that are classified as priority level 1 or priority level 2; these classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer will automatically open a case.

To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to the following URL:

http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Before calling, please check with your network operations center to determine the level of Cisco support services to which your company is entitled; for example, SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). In addition, please have available your service agreement number and your product serial number.

This document is to be used in conjunction with the documents listed in the "Documentation Roadmap" section.


Copyright © 2002, Cisco Systems, Inc.
All rights reserved.


hometocprevnextglossaryfeedbacksearchhelp
Posted: Thu Jul 25 12:39:27 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.