|
|
To get specific information about an error message from within the ISM program, position the cursor on a message and press PF1. You can also use the ismhmsg command from any ISM command line to get ISM message help.
 |
Note ISM uses the prefix NSP for all messages. Some messages contain site-specific data, represented in this appendix by values such as parm.2 and parm.3. |
NSP1001I PF Key not supported.
Explanation You pressed a function key that is not supported from this panel. Only those function keys displayed at the bottom of the panel are supported.
Action Verify the action you are attempting to perform and select the appropriate function key from those displayed at the bottom of the panel.
NSP1002I Operator parm.2, is not the authorized ISM Manager. parm.3 is the correct manager.
Explanation This message is created when an operator other than the designated operator issues the isminit command.
Action Issue the isminit reset command to reset ISM. At a NetView command prompt, issue the autotask opid=ismmgr command, where ismmgr is the designated installation autotask for ISM manager.
NSP1003I ISM Initialization was done at parm.2.
Explanation This message occurs when an operator issues the isminit command without a correct option.
Action Issue the isminit reset command to reset ISM. At a NetView command prompt, issue the autotask opid=ismmgr command, where ismmgr is the designated installation autotask for ISM manager.
NSP1005E Build for parm.2 failed, parameter = parmlist.
Explanation This message is generated when incorrect data is passed to either the NSPIBCV4 or NSPIBCF3 routines.
Action Enable the TRFLOW service aid in ISM to find out what data is being passed internally as the routines are executed.
NSP1006I ISM storage resident routines loaded by parm.2
Explanation This message is generated when routine NSPILD4 is executed.
Action None.
NSP1007I There is no previous panel.
Explanation You requested to view a previous panel of information when none exists. Previous panels exist only if PF7 is displayed at the bottom of the panel.
Action None.
NSP1008I There is no continuation panel.
Explanation You requested to view a continuation panel of information when none exists. Continuation panels exist only if PF8 is displayed at the bottom of the panel.
Action None.
NSP1009I Cursor not on a valid line.
Explanation You pressed Enter when the cursor is not positioned in a valid location on the panel.
Action Ensure that the cursor is positioned in a valid location and press Enter.
NSP1010I You are at the left most panel.
Explanation You pressed PF10 to request to view additional data on the left side of the panel when none exists.
Action None.
NSP1011I You are at the right most panel.
Explanation You pressed PF11 to view additional data on the right side of the panel when none exists.
Action None.
NSP1012I No command to retrieve.
Explanation You requested to retrieve archived commands when all previously issued commands were already retrieved.
Action None.
NSP1013E parm.2 command canceled by operator.
Explanation An issued runcmd was terminated by an operator who issued a cancmd against the service point of the resource to which the runcmd was issued.
Action Check the NetView log to verify that a cancmd was issued.
NSP1014E VTAM reported error, parm.2 not responding. See the NetView log.
Action This message indicates that the service point you specified is not available to VTAM. This failure can be caused by one of the following:
Action View the NetView log for the reason for this failure.
NSP1015I VTAM DSPU name is required.
Explanation You requested to perform an action that requires a VTAM DSPU name and you did not specify one.
Action Specify a valid VTAM DSPU name and resubmit your request.
NSP1016I VTAM PU name required.
Explanation You are defining a DSPU resource and are being prompted to specify the DSPU name (VTAM PU name) of the resource. This is a required field.
Action Specify a valid DSPU name (VTAM PU name) and press Enter.
NSP1017E Error for VTAM command parm.2.
Explanation The NSPRVDIS routine experienced a VTAM command failure when attempting to determine the VTAM status of a resource.
Action Display the VTAM resource to confirm the error.
NSP1018E Timeout for VTAM command parm.2.
Explanation The NSPRVDI3 routine did not receive a response from VTAM within 20 seconds. Timeout occurs after 20 seconds.
Action Display the VTAM resource to confirm the error.
NSP1019I VTAM node definition not specified.
Explanation You attempted to create a resource definition without specifying a VTAM node definition.
Action Verify that you created a PU definition in VTAM for the resource.
NSP1020E Bad return code from RUNCMD. Return Code = parm.2.
Explanation A runcmd that was issued to a resource has failed. The NetView log may contain information that can help determine the cause of this failure.
Action View the NetView messages logged for that resource to determine the possible actions that should be taken. If you are unable to determine the cause of the failure, contact network support for assistance with this error.
NSP1021I Cisco resource interface parm.2 management initialization started.
Explanation The request to initialize an interface type was received and the ISMIINIT routine is building the environment to manage that interface type.
Action None.
NSP1022I parm.2 parm.3 management initialization completed.
Explanation The request to initialize an interface type was received and completed by ISM.
Action None.
NSP1023I Cisco resource management initialization started.
Explanation This message is logged when the ISM initialization is started by the ISMINIT routine.
Action None.
NSP1024I Cisco resource management initialization completed. Entries = parm.2.
Explanation This message is logged when the ISM initialization is completed by the ISMINIT routine. The number displayed in the Entries field is the number of resources being monitored by ISM.
Action None.
NSP1025E Help not available.
Explanation You requested help for a function that does not have help information.
Action None.
NSP1026E Enter ISMIINIT parm.2 INIT to re-initialize.
Explanation The ISMIINIT routine was issued to initialize a type of interface when the ISMIINIT routine was already used to initialize the interface.
Action If necessary, issue the ismiinit init command to re-initialize the interface type.
NSP1027E Enter ISMINIT INIT to re-initialize.
Explanation The ISMINIT routine was issued to initialize ISM, when the ISMINIT routine was already used to initialize ISM.
Action Issue the excmd ismmgr isminit init command. The ISMINIT routine should be executed only by the ISMMGR autotask. If an operator issues the isminit init command, that operator takes over the functions of ISMMGR.
NSP1029E parm.2 interface initialization failed.
Explanation The interface initialization failed for the interface parm.2.
Action Browse the NetView log for >NSPIIN4. The reason for the failure is explained in the text following this header in the log.
NSP1030I parm.2 interface initialization was done at parm.3.
Explanation The ISMIINIT routine was issued to initialize a specific type of interface when that interface was already initialized.
Action If necessary, issue the ismiinit n init command, where n is the letter that represents the interface type that you want to re-initialize. The values for the types of interfaces you can view are:
NSP1031I No ISMDSA data set, initialization will not be done.
Explanation The VSAM support required for ISM was not available.
Action Verify that the ISMDSA task is active.
NSP1032E SETUP record not found. Do ISMSETUP before doing a ISMINIT.
Explanation An attempt was made to initialize ISM before ISMSETUP was performed.
Action From the ISM main menu panel, select SETUP. After you specify your setup options, log off the ISMMGR autotask and start the ISMMGR autotask.
NSP1034E ISM is not initialized.
Explanation You attempted to use an ISM routine, but ISM was not initialized. You will receive this message in the following situations:
Action Initialize ISM and retry your request. If ISMMGR is active, look in the log for message NSP1032I (ISM not enabled). Access ISM setup from the ISM main menu panel and press PF10 to show the active ISM variables. If the values for the variables are blank, then ISM setup was not performed. Proceed to enable the ISM management options.
NSP1035I You must exit your session with parm.2.
Explanation You attempted to toggle from the ISM Resource Configuration Collector panel without properly exiting your enabled session. When a resource is enabled to an operator, no other operator can communicate with it.
Action To properly exit the enabled session, type EXIT in the Command Input field beneath the Host name field and press Enter. Press PF3 to exit the Resource Command Interface panel.
NSP1036E Input error, enter a valid option and press Enter.
Explanation You entered an option that is not available on the popup menu.
Action Review the Resource Management popup menu, enter a valid option, and press Enter.
NSP1037I Make changes and press Enter to validate.
Explanation You are authorized to make changes to the data displayed on this panel.
Action If you make changes to the data, press Enter to verify the changes, and press PF4 to save the changes.
NSP1038I Press Enter for prompted input.
Explanation Instructions on specifying values for the fields on this panel are available.
Action If necessary, press Enter for instructions on specifying values for the fields on this panel.
NSP1039I Press PF4 to go to update mode.
Explanation You are authorized to make changes to the information displayed on this panel.
Action To make changes to a resource, press PF4.
NSP1040I Press PF4 to implement changes or PF3 to exit.
Explanation You made changes to the information displayed on the panel.
Action To save and implement the changes you made, press PF4. To exit the panel without implementing or saving the changes, press PF3.
NSP1041I Press PF4 to update resource management data.
Explanation You are authorized to make changes to the information you are viewing on the Resource Management Data panel.
Action To begin making changes, press PF4 to display the Cisco Resource Definition.
NSP1043I Press PF4 to delete parm.2 setup.
Explanation You requested to delete the ISM setup by specifying the Delete option in the Change field on the ISM Resource Management Setup panel.
Action Ensure that you want to delete the ISM setup. Press PF4 if you are sure that you want to delete the ISM setup.
NSP1044I Press PF4 to delete resource.
Explanation You requested to delete a resource. If this resource is a router, the router definition, router history, interfaces configured in the router and the interface history archived will be deleted. If you are deleting an operator profile, see the Recommended Action.
Action If you are deleting an operator profile, issue the ismusers command to ensure that the operator profile that you are deleting is not the only remaining ISM administrator profile. Verify that your request is accurate and press F4 to delete the resource.
NSP1046I At least one filter is required.
Explanation You enabled status filtering by specifying Y in the Status Filters field on the ISM User Administration panel, and have not specified a status type in the Filter 1, 2, or 3 fields.
Action To enable status filtering, type Y in the Status Filters field, and specify at least one status type in the Filter 1, 2, or 3 fields. To disable status filtering, type N in the Status Filters field. The following status filters are valid:
NSP1047I At least one group is required.
Explanation You enabled group filtering by specifying Y in the Group Filters field on the ISM User Administration panel, but you did not specify a group in the Group 1 or Group 2 fields. Enabling group filtering requires that you specify a group.
Action To enable group filtering, type Y in the Group Filters field and specify at least one group in the Group 1 or Group 2 fields. To disable group filtering, type N in the Group Filters field.
NSP1048I Description not provided.
Explanation You are defining a resource and are being prompted for a description. This field is optional and for information only.
Action None.
NSP1051I Record parm.2 deleted.
Explanation The VSAM control file of the record you requested to delete was deleted.
Action None.
NSP1052I Record parm.2 added.
Explanation The VSAM control file was added or updated with the changes you made.
Action None.
NSP1054I Collection Complete for parm.2; parm.3 records collected.
Explanation Your request to collect and archive the current configuration of the resource was successfully completed.
Action None.
NSP1055E Delete failed for record parm.2; Return Code = parm.3.
Explanation Your request to delete a record failed. This message indicates that the routine NSPVSAM4 was unsuccessful when attempting to delete a VSAM control file. A return code 1 indicates that the VSAM command timed out. A return code 2, indicates the record was not found.
Action Check the NetView log for messages 1098, 1106, 1107, and 1108. If the file was deleted already, this error message is normal.
NSP1056I Resource not known: Press Enter for prompted input.
Explanation The control name of the specified resource is unknown to ISM. However, you are authorized to define the resource to ISM.
Action Verify and re-enter the control name if this is a previously defined resource, or press Enter for prompts to define a new resource.
NSP1057E Updating failed for record parm.2; Return Code = parm.3.
Explanation The NSPVSAM4 routine was unable to update a record. If the return code is 1, the routine may be out of VSAM space.
Action Check NetView log for messages 1098, 1106 1107 and 1108.
NSP1059E Authorization error. parm.2 cannot do a reset.
Explanation You issued the nspoper3 command to reset a session between an operator and a resource while you are not authorized to perform this action. To reset a session, you must be an enabled ISM user.
Action If the session between an operator and resource needs to be reset, find an authorized operator to perform the operation.
NSP1060E Unauthorized attempt to execute parm.2.
Explanation You requested to define, update, or delete a resource interface while you are not authorized to perform this action. To modify a resource interface, you must be an enabled ISM user.
Action If the resource interface needs to be modified, find an authorized operator to perform the operation.
NSP1061E You are not authorized to change the ISM DSPU environment.
Explanation You attempted to modify the ISM DSPU environment while you are not authorized to perform this action. To modify the ISM DSPU environment, you must be an enabled ISM user.
Action If the ISM DSPU environment needs to be modified, find an authorized operator to perform the operation.
NSP1062E You are not authorized to change the ISM Setup environment.
Explanation You attempted to modify the ISM setup while you are not authorized to perform this action. To modify the ISM setup, you must be an ISM administrator.
Action Contact an ISM administrator to perform the operation.
NSP1063E You are not authorized.
Explanation You attempted to perform an action for which you are not authorized.
Action Contact an ISM administrator to change your user authority settings.
NSP1064I Resource parm.2 already defined.
Explanation You attempted to define a resource that was already defined to ISM.
Action None.
NSP1067I Resource parm.2 busy; enabled by operator parm.3.
Explanation You attempted to establish an enabled session with a resource enabled to another operator.
Action Ensure that the operator enabled to the resource is logged on by performing a list parm.3. If the operator is not logged on, use the RESETOP option on the Resource Status panel (NSPVMGRT) to reset the session between the resource and operator.
NSP1068I Resource parm.2 deleted from ISM manager.
Explanation The request to delete a resource definition was successfully completed. The message is also written to the NetView log for tracking purposes.
Action None.
NSP1069I Resource parm.2 not known.
Explanation You attempted to delete the definition of a resource not known to ISM.
Action None.
NSP1071I Resource name has bad syntax.
Explanation The syntax of the control name you specified was incorrect. Control names may be a combination of up to eight alphanumeric characters. Special characters are not valid.
Action Verify the control name you entered and re-enter the control name using valid characters.
NSP1073I Resource unavailable because it is enabled by parm.2.
Explanation The RUNCMD failed because the resource is enabled by another operator.
Action Ensure that the operator enabled to the resource is logged on by performing a list parm.3. If the operator is not logged on, use the RESETOP option on the Resource Status panel (NSPVMGRT) to reset the session between the resource and operator.
NSP1074I Resource host name not provided.
Explanation You are defining a resource and are being prompted to enter the Resource Host Name field. If a VTAM definition currently exists for the resource, this information is automatically obtained.
Action None.
NSP1075I Last record not found.
Explanation Your request to retrieve the history records was denied because ISM could not locate the last record.
Action None. When the next history record is recorded by ISM, this problem will be corrected.
NSP1076I Resource control name is required.
Explanation You attempted to define a resource without specifying its control name. The control name is up to eight alphanumeric characters and is a required field.
Action Specify the control name of the resource and press Enter.
NSP1078I parm.2 is not a monitored resource.
Explanation You bypassed ISM and issued an ISM routine to monitor a resource undefined to ISM. To monitor a resource using ISM routines, the resource must be defined to ISM.
Action None.
NSP1079I New interface discovered parm.2, parm.3, parm.4.
Explanation A new interface that was not previously defined to ISM was discovered.
Action None.
NSP1080I No data available for resource parm.2.
Explanation A request for the configuration of a resource failed because the configuration for the resource is not stored in NetView variables.
Action If you are an enabled ISM user, use Option 7 on the popup menu to collect the current resource configuration.
NSP1081I Now collecting interface data for resource parm.2.
Explanation The ISM ISMISTAT routine is collecting data from the interfaces to be monitored by ISM.
Action None.
NSP1082I Now collecting interface status for resource parm.2.
Explanation The ISM NSPISTAT routine is collecting status data for the specified interface. This message occurs only when the ISMAID DEBUG facility is set to YES.
Action None.
NSP1084I Resource configuration saved for parm.2.
Explanation The resource configuration you collected was successfully archived.
Action None.
NSP1085I Configuration management options not specified.
Explanation You are defining a resource and are being prompted to enter its IP address. This field is optional and for information only.
Action None.
NSP1086I No Response from retrieve.
Explanation You requested data from a resource and the resource did not respond.
Action Issue the ismr resource-name command. Use the options to diagnose the problem.
NSP1087I IP address not provided.
Explanation You are defining a resource and are being prompted to enter its IP address. This message is for information only.
Action None.
NSP1088I Request to delete history records issued.
Explanation Your request to delete interface history records was issued.
Action None.
NSP1091E Database not defined.
Explanation The internal routine NSPVSAM4 was called by ISM with the incorrect parameters. This error message indicates an ISM routine error, not a user error.
Action None.
NSP1092I Database now being updated for parm.2.
Explanation This message is created after every 40 records are saved in the VSAM configuration data base.
Action None.
NSP1095I No data found in NSPDB data base for parm.2.
Explanation The calling routine could not find VSAM records required by the routine. The records may have been deleted earlier or are not yet available.
Action None.
NSP1098E NSPDS failed, message = parm2.
Explanation A VSAM request for ISM data failed.
Action The data that follows this message indicates the reason for the failure.
NSP1099E VSAM update error. Error = parm.2.
Explanation The ISM NSPSCON3 routine received a VSAM error while saving a resource configuration.
Action The data that follows this message indicates the reason for the failure.
NSP1100I There is no operator monitoring parm.2.
Explanation You requested to reset a session between a resource and an operator by issuing the nspoper3 command without specifying an operator ID, or by using the RESETOP function key on a resource not currently in a session with an operator.
Action View the Resource Status panel to verify that a session is established between the resource and an operator and, if so, reset the session by issuing the nspoper3 command and specifying the resource name and operator ID or by using the RESETOP function key.
NSP1103I Trace Data >> parmlist.
Explanation This message is written to the log when the ISMAID service aid DEBUG is turned on.
Action None.
NSP1104I Module Entry Trace >> parmlist.
Explanation This message is displayed only when the ISMAID service aid TRFLOW is set to ON. It contains the data passed to the routine when it is called.
Action None.
NSP1105I Module Exit Trace >> parmlist.
Explanation This message is displayed only when the ISMAID service aid TRFLOW is set to ON. It contains the data and error conditions from the routine's exit.
Action None.
NSP1106E Command parm.2 failed. Operator replied GO.
Explanation This error message occurs if a WAIT command is terminated by the operator entering GO from a NetView command line. The WAIT command should have an internal timeout value and indicate a timeout when the WAIT function fails.
Action Retry the routine and see if the problem recurs.
NSP1108E Command parm.2 timed out.
Explanation The command specified in the message has timed out.
Action Re-issue the command. If the failure recurs, contact your NetView system programmer for assistance.
NSP1111E Requires session to be enabled.
Explanation You requested to collect the current configuration of a resource by issuing the nspgetc3 command without establishing an enabled session with that resource.
Action If you are an authorized enabled ISM user, use Option 7 on the resource options menu to establish an enabled session with the resource and collect the current configuration.
NSP1112E Status Collection complete for parm.2, Number of interface = parm.3.
Explanation Your request to collect information about the interfaces configured in a resource by issuing the ismistat command was successful. This message appears only if the ISMAID service aid is set to on. The number of interfaces discovered is also displayed in this message.
Action None.
NSP1113I Insufficient number of parameters passed with command.
Explanation A routine could not execute because of insufficient input parameters.
Action If the routine was called via another routine, turn on the ISMAID TRFLOW service aid and repeat the action.
NSP1116I Operator parm.2 not known.
Explanation You are not defined as an ISM user. This message is generated when you perform an ISM function and ISM verifies that your operator ID is defined to ISM (via an ISM profile). All functions performed using ISM are monitored, and this message is displayed as long as you are undefined to ISM.
Action Have an ISM administrator create an operator profile using the USER option available on the ISM main menu.
NSP1117I Operator Group ID not specified.
Explanation You are defining a resource and are being prompted to specify a group to which this resource belongs in the Operation Group ID field. Operator groups may be all resources located in a region or department, or resources of a particular device type. You can filter resources by the Operation Group. This field is optional.
Action None.
NSP1118I Operator ID required.
Explanation You attempted to create an operator profile without specifying a name in the Operator Name field.
Action Specify the name of the operator in the Operator Name field and resubmit your request.
NSP1119I Operator parm.2 is no longer router manager for parm.3.
Explanation This message is created when the nspoper3 command is issued against the specific service point and an enabled operator was managing the resource.
Action None.
NSP1120I All values have been reset for ISM by parm.2.
Explanation This message is displayed when the isminit command was issued with the reset option specified. The isminit reset command clears all variables associated with managing the resources.
Action Issue the isminit command to rebuild the variables.
NSP1121I Entered with invalid value for parm.2.
Explanation The NSPHIST4 command was issued with an invalid value specified. NSPHIST4 is the command history recording routine.
Action Verify the values specified and resubmit your request.
NSP1122I Entered with invalid parameters: parm.2.
Explanation The NSPHIST4 command was issued with invalid parameters. NSPHIST4 is the command history recording routine.
Action Verify the specified parameters and resubmit your request.
NSP1124I Input not found at row = parm.2, column = parm.3.
Explanation The cursor is in a position on the panel that does not contain the required data for processing.
Action Verify that all required data was specified and resubmit your request.
NSP1126E Invalid resource name parm.2 given.
Explanation The resource name passed with the NSPRVDI3 routine is unknown to VTAM.
Action Ensure that the resource is properly defined to VTAM.
NSP1129I CTRACE set to >parm.2<
Explanation The current ISMAID service aid settings are those identified in this message. This message is for information only.
Action None.
NSP1131E SAFE failed, Message = parm.2.
Explanation The request to retrieve resource history data (NSPRDI4 routine) has failed.
Action Contact your system programmer.
NSP1132I Action type must be either 1, 2, or 3.
Explanation You attempted to make changes without specifying whether you want to implement your changes at the next startup of ISM, implement them in the current session only, or implement them in the current session and save the changes for future ISM sessions.
Action Enter the number representing the action you want to perform in the Action Type field:
NSP1133I Change type must be either 1, 2, or 3.
Explanation You attempted to make changes without specifying whether you are defining a new resource, updating an existing resource, or deleting a resource.
Action Type the number representing the type of change you wish to make in the Change Type field.
NSP1134I Change type must be either 2 or 3.
Explanation You made changes to a panel without specifying the type in the Change Type field. You must specify 2 for update or 3 for delete.
Action Specify a type in the Change Type field, and resubmit your request.
NSP1135I Resource not known: Press PF3 to exit.
Explanation The service point name you entered is not a resource known or managed by ISM.
Action Verify the control name of the resource for which you attempted to display management data. If the resource is valid but not defined to ISM, contact an ISM administrator to define the resource.
NSP1136I Resource not known: Press PF4 to define router.
Explanation The control name you entered is not a resource known or managed by ISM. However, you are authorized to define a new resource.
Action Verify the service point name of the resource for which you are attempting to display management data. If the resource is not known to ISM, press PF4 to define the resource.
NSP1139I DSPU Host name is required.
Explanation You are defining a DSPU resource and are being prompted to specify the DSPU host name of the resource. This is a required field.
Action Specify a valid DSPU host name and press Enter.
NSP1141E parm.1 parameter should be CTRACE, DEBUG, TRFLOW, or OFF.
Explanation You issued the ismaid command and specified a parameter other than CTRACE, DEBUG, TRFLOW, or OFF.
Action Re-issue the ismaid command with one of the above parameters or, to display help on using the ISM service aid type ismaid.
NSP1142I Please enter the parm.2 parm.3.
Explanation You attempted to execute an ISM routine without specifying the required parameters.
Action Re-issue the routine and ensure that you specify all required parameters.
NSP1143I Select option number and press Enter.
Explanation You are on a panel from which you can perform a function by selecting an option number.
Action Enter an option number from the list displayed on the panel. The input will be examined starting at the first character position.
NSP1144E Input parm.2 not recognized.
Explanation The routine does not recognize the input.
Action Verify the purpose of the routine and retry with different input.
NSP1145I parm.2; Press PF6 to return.
Explanation This message is displayed on NetView panels when you press PF6 on an ISM panel. The field that follows the message ID identifies the ISM routine that is suspended until you press PF6 again to return to an ISM screen.
Action None.
NSP1146I Router parm.2 not active to VTAM.
Explanation The ISM status of the resource indicates that the resource is not ACTIV to VTAM.
Action Display the Resource Status panel, select the resource, and press Enter. Select Option 5 on the popup menu to view the resource from VTAM. If the status is ACTIV, press PF3 and select Option 9 from the popup menu to reset the status of the resource status. ISM will check the availability of the resource.
NSP1147I Service point parm.2 already managed by operation_id.
Explanation You are attempting to establish a session with, or issue commands to, a resource currently in a session with another operator. The ID of the operator busy with the resource is displayed in this message.
Action Display the Resource Status panel to view the operator ID. If the operator is not logged on and you are an enabled ISM user, you can reset the session. To do so, position the cursor on the service point name or operator ID and press PF9.
NSP1148I More data available, press PF8. Enter N to terminate.
Explanation You issued the show mem command and there are additional pages of data. The Host name field contains the word "More" when more data is pending from the resource.
Action To view the additional pages of data, press PF8, or to terminate the display, type N.
NSP1149I Router command parm.2 cannot be used with service point interface.
Explanation The command you issued cannot be executed through the resource service point at this time. The command you issued is one of a group that provides output to the operator at a later time. The service point does not support asynchronous operations at this time. There is no way for the unsolicited responses to be sent back to the operator who issued the command. For example, telnet is a command that should not be sent to the resource.
Action To connect directly to the resource, use a local console or Telnet via a TCP/IP session.
NSP1150I Enter password.
Explanation You are performing a function that requires you to enter a password to establish an enabled session with the resource.
Action To establish the enabled session, enter the enable password exactly as it is defined to the resource. If you do not know the enable password, or if you want to cancel the enable request, entering an invalid password three times terminates the enable request.
NSP1151I Password field empty, enter password.
Explanation You attempted to enable to a resource without specifying a password. A password must be specified when requesting an enabled session.
Action To establish the enabled session, enter the enable password exactly as it is defined to the resource. If you do not know the enable password and you want to cancel the request, enter an invalid password three times.
NSP1152I More data available. Enter Y to continue; N to terminate.
Explanation You issued the show mem command and you are on the last page of the first set of data returned from the resource. The Host name field contains the word "More" when more data is pending from the resource.
Action To display additional data, type Y. To terminate the display, type N.
NSP1153I You are not authorized to do an enable.
Explanation You requested to establish an enabled session with a resource. You are not authorized by an ISM administrator to establish an enabled session.
Action Ensure that your ISM user authority settings in your profile are correct. If the settings are not correct, contact an ISM administrator to change them.
NSP1154I Press PF3 to terminate enable.
Explanation You are currently in an enabled session with the resource. While you are enabled to the resource, no other operator can communicate with the resource.
Action To properly terminate the enabled session, press PF3. Pressing PF3 terminates your enabled session with the resource by sending an EXIT RUNCMD to the resource. This RUNCMD frees the resource for other operator use.
NSP1155I Input parameter parm.2 should be a numeric value.
Explanation A non-numeric value was detected by the NSPMCHK4 routine. The NSPMCHK4 routine calculates the free resource memory based on the values collected from the resource.
Action None.
NSP1157I parm.2 parm.3 parm.4 has been executed by parm.5.
Explanation This message indicates that the ismiinit command was issued with the RESET option. This message is for monitoring purposes only.
Action None.
NSP1158I Config DB save started for parm.2 parm.3.
Explanation The resource configuration you just collected is now being stored in the VSAM configuration data base.
Action None.
NSP1159E Unexpected output from VTAM parmlist.
Explanation You requested to view the resource as defined to VTAM, and the output from VTAM was not recognizable.
Action Issue the command displayed in this message and check the output. If the output is recognizable, but your request for the VTAM resource configuration fails again, consult your NetView support.
NSP1160I parm.2 is no longer enabled to or controlling parm.3, reset by parm.4.
Explanation If you requested to reset an enabled session between a resource and operator, this message indicates that your request has completed successfully. If you received this message while in a session with a resource, it indicates that the session between you and the resource was terminated.
Action None.
NSP1161I parm.2 no longer is busy with router parm.3.
Explanation Your request to reset a busy session between an operator and a resource has completed successfully.
Action None.
NSP1162I Operator has been changed, origin = parm.2, New = parm.3.
Explanation You requested to reset a session between an operator and resource, and the operator you specified is no longer the current operator. This indicates that the busy condition no longer exists for the specified resource, or that a new operator has established a session with the resource.
Action Display the Resource Status panel to verify the operator, if any, that may be enabled to, or busy with, the resource.
NSP1163I parm.2 interface records deleted for parm.3.
Explanation Your request to delete the performance or history records for an interface has completed successfully.
Action None.
NSP1164I An interface type of A, M, C, E, D, F, H, B, L, S, T, U, G, N, or I is required.
Explanation You requested to view a list of interfaces monitored in the network by type and you did not specify an interface type.
Action Specify a type in the Interface Type field and resubmit your request. Valid values are:
NSP1165I There is no parm.2 available for parm.3 on parm.4.
Explanation You requested to view the performance or history data archived for a specific interface for which no data was archived.
Action None.
NSP1166I 15 minutes is the minimum interval.
Explanation You set the resource monitoring interval to less than 15 minutes on the ISM Resource Management Setup panel. The minimum interval for resource monitoring is 15 minutes. The interval will be set to 15 minutes.
Action Reset the resource monitoring interval to a value of 15 minutes, or longer, or accept the ISM minimum default of 15 minutes.
NSP1167I Router status refresh request sent to ISMMGR.
Explanation Your request to refresh the status of the resources on the Resource Status panels was sent to ISM.
Action Wait for the ISM to query and collect the status of the resources and then press PF12 to view the updated status.
NSP1168I There are no parm.2 interfaces for parm.3.
Explanation You requested to view a list of a specific type of interfaces configured in a resource, and the interfaces were not configured or discovered in that resource.
Action None.
NSP1169I Interface type parm.2 not initialized.
Explanation You requested to view the status of a specific interface type that was not initialized.
Action To initialize the interface type, issue ismiinit n init, where n is the type of interface you want to initialize. Valid values are:
NSP1170I Router busy with operator parm.2.
Explanation You attempted to issue a RUNCMD to a resource in an enabled or busy session with another operator. The RUNCMD you issued is attempted for 10 seconds before this message is generated.
Action If you are an enabled ISM user, you can terminate the session between a resource and an operator from the Resource Status panel. To do so, position the cursor on the operator ID and press PF9. If you get this message each time you attempt to issue the RUNCMD to the resource, display the Resource Status panel to view the operator in an enabled or busy session with the resource.
NSP1171I No changes have been made to parm.2.
Explanation You exited the ISM setup without making changes.
Action If you intended to make changes to the ISM setup, make the changes again and press Enter to verify your changes and press PF4 to save your changes and exit the ISM setup.
NSP1172E RUNCMD Time-out, parm.2 not responding; See the NetView log.
Explanation You issued a runcmd command to an unresponsive resource. This error generally indicates an internal problem that prevents the resource from responding to the RUNCMD.
Action Verify that the resource service point is configured properly, and that it is defined as a PU to VTAM.
NSP1173I Screen copied to log.
Explanation Your request to copy the information on the panel to a log by pressing PF5 was processed successfully.
Action None.
NSP1177I Interface State Change parmlist
Explanation This message is written to the event log when an interface has a state change. The last parameter identifies the routine that created the message.
Action Issue the ismr resource-name command to check the resource status.
NSP1178I Resource State Change parmlist
Explanation This message is written to the event log when a resource has a state change. The last parameter identifies the routine that created the message.
Action Issue the ismr resource-name command to check the resource status.
NSP1186I Position cursor on resource and press PF5 to diagnose status.
Explanation By pressing PF5, the status of the resource will be analyzed and the appropriate action will be taken to assist in diagnosing the reason for the status condition.
Action Press PF3 and then press PF1 to get help on the meaning of the status colors.
NSP1187I Press PF5 to diagnose the current status of the resource.
Explanation By pressing PF5, the status will be analyzed and the appropriate action will be taken to assist in diagnosing the reason for the status condition.
Action Press PF3 and then press PF1 to get help on the meaning of the status colors.
NSP1188I Position cursor on target and press enter to view target summary.
Explanation This operation should display the same ISMSUM data presented on the target system by a local operator.
Action None.
NSP1189I Operator parm.2 of domain parm.3 has changed status of parm.4 from parm.5 to parm.6.
Explanation This message is created to provide an audit trail of operator actions that affect monitored resource status.
Action None.
NSP1200I Operator xxx of domain cccc has issued a REFRESH/RESET for resource ssss.
Explanation This message is written when an operator enters option 9 from the Resource Status with Options menu. This message is part of the audit trail for ISM managed resources.
Action None.
NSP1201I Command or option is not supported by this resource.
Explanation This message indicates an operator error.
Action Use a different command or option.
NSP1202I No data available for this selection.
Explanation The called routine was unable to find any resources that matched the input status. The status could have changed, but the status panel was not yet updated.
Action Press the refresh option if available.
NSP1203I There are no resources that match your viewing filters.
Explanation The called routine was unable to find any resources that matched your viewing filters. You may have group filters that allow you to view only specific resources and related resources.
Action Issue the ismuser command to display your filter definitions.
NSP1204I Resource parm.2 has been changed by parm.3.
Explanation This message is used to provide an audit trail. When an operator changes a control file for a monitored resource, a message is written to the ISM event log.
Action None.
NSP1900I parm.2 parm.3
Explanation This message is written when the NSPDS command processor has completed an operation. The message parm.2 is the key and parm.3 is the action taken. If the command was a list, then the message contains the data record.
Action None.
NSP1901I END OF LISTING
Explanation This message is written when the NSPDS command processor completes a list operation. The message is written when all the data records are processed.
Action None.
NSP1910I REQUEST HAS BEEN QUEUED
Explanation This message is written when the NSPDS command processor receives a command.
Action None.
NSP1912E MAX NUMBER OF PARAMETERS REQUIRED
Explanation This message is written when the NSPDS command processor detects an input command error. In this case the number of input parameters is too high.
Action None.
NSP1998I Invalid service type for NSPMBLD. parms
Explanation This message indicates an error in the calling routine and that the type of service was not an L, V, B, or R.
Action Check the routine that called NSPMBLD, and contact your system programmer.
NSP1999I Message not found in the table. parms
Explanation This message is created by routine NSPMBLD when it receives a message to process not found in the message table in NSPMBLD. This message should not occur.
Action Contact your system programmer.
NSP2015I puname netid session_data
Explanation This message is created when the VTAM exit ISTEXCCS is executed. The data in the message string is parsed and archived by ISM.
Action Type the NSPSDIS3 PU name to view archived data.
NSP2091E ISM LICENSE KEY WAS NOT SPECIFIED
Explanation This message is issued when NSPSEVDT is unable to read or parse the DSIPARM(ISMLICSE) member.
Action Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
NSP2092E LENGTH OF LICENSE KEY MUST BE 40 BYTES
Explanation This message is issued when NSPSEVDT has read and parsed the DSIPARM(ISMLICSE) member but found that the license key is not of the correct length.
Action Verify that the DSIPARM(ISMLICSE) member contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
NSP2093E ISM IS RUNNING ON AN UNLICENSED CPU.
Explanation This message is issued when NSPSEVDT has read and parsed the DSIPARM(ISMLICSE) member but found that the license key does not allow ISM to execute on the current CPU.
Action Verify that the DSIPARM(ISMLICSE) member contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
NSP2094E DSIDKS TYPE=CONN FAILED FOR DSIPARM.
Explanation This message is issued when NSPSEVDT is unable to read the DSIPARM(ISMLICSE) member.
Action Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
NSP2095E UNABLE TO LOCATE DSIPARM(ISMLICSE).
Explanation This message is issued when NSPSEVDT is unable to read the DSIPARM(ISMLICSE) member.
Action Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
NSP2096E READ FAILED FOR DSIPARM(ISMLICSE).
Explanation This message is issued when NSPSEVDT is unable to read the DSIPARM(ISMLICSE) member.
Action Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
NSP2097E YOUR ISM LICENSE WILL EXPIRE. DAYS LEFT: &days
Explanation This message is issued when the license key specified in the DSIPARM(ISMLICSE) member indicates that there are fewer than 30 days left on this license. ISM continues to operate until the license key expires.
Action Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
NSP2099E NO LICENSE FOUND FOR ISM.
Explanation This message is issued when a module in ISM is unable to determine the current licensing environment. ISM ceases to function.
Action Verify that the DSIPARM(ISMLICSE) member exists and that it contains a valid license specifier in the form:
ISMLICENSE=LicenseKey
Posted: Tue Dec 12 15:34:14 PST 2000
Copyright 1989-2000©Cisco Systems Inc.