|
|
Table Of Contents
2.1 Setting up TL1 Communication
Open a TL1 Session Through CTC
Open a TL1 Session Through Telnet
Open a TL1 Session Through a Craft Interface (Cisco ONS 15454, ONS 15310-CL, and ONS 15310-MA)
Open a TL1 Session Through a Craft Interface (Cisco ONS 15600)
2.2.2 TAP Creation and Deletion
2.2.3 Connect Test Access Points
2.2.5 Retrieve Test Access Point Information
2.2.6 Disconnect Test Access Points
2.2.7 Delete Test Access Points
2.2.8 Test Access Configurations
2.2.9 Test Access Mode Definitions
2.2.10 Unmapped AID Test Access Point Connections
2.3.1 Gateway Network Element Topology
2.3.2 ONS 15454, ONS 15310-CL, and ONS 15310-MA Gateway
2.3.4 Implementing TL1 Gateway
2.5.1 Provision a PCA Cross-Connection
2.5.2 Retrieve a PCA Cross-Connection
2.6.4 Downloading New Software
2.6.6 Remote Software Download/Activation Using the GNE
2.7.1 Create a PM Schedule and Receive an Autonomous PM Report
2.7.3 Enable or Disable a TL1 Session to Receive Autonomous PM Reports
2.8.2 Bridge and Roll TL1 Commands
2.8.3 Two-Way Circuit Single Roll and Dual Roll Procedures
2.8.4 One-Way Circuit Single Roll and Dual Roll Procedures
2.8.5 Protection Rolling Procedures
2.9 1:N Low-Density to 1:N High-Density Upgrade
2.10 Remote Monitoring-Managed PMs
2.10.4 RTRV-RMONTH-<MOD2_RMON>
2.10.5 REPT EVT <MOD2ALM> for Threshold Crossing Events
2.10.11 MONTYPE and CONDEF Defined for TCA
2.10.13 Notes for DWDM Card Types
2.11 Rules for Framing Type Autoprovisioning in CTC Versus TL1
2.12 Provisioning Rules for Transponder and Muxponder Cards
2.12.2 Payload Provisioning Rules
2.12.3 OC-N Payload Provisioning Parameters
2.12.4 Termination Mode Provisioning Rules
2.12.5 Wavelength Provisioning Rules
2.12.6 Regeneration Group Provisioning Rules
2.12.7 DCC/GCC Provisioning Rules
2.12.8 ITU-T G.709 OTN, FEC, and OTN SDBER/SFBER Provisioning Rules
2.12.9 Synchronization Provisioning Rules
2.12.10 Section Trace Provisioning (J0) Rules
2.12.11 Trail Trace Identification Provisioning Rules
2.12.12 PM and Alarm Threshold Provisioning Rules
2.12.13 Y-Cable Protection Group Provisioning Rules
2.12.14 Splitter Protection Group Provisioning Rules
2.12.15 Loopback Provisioning Rules
2.12.16 Automatic Laser Shutdown Provisioning Rules
2.12.17 Port State Model Provisioning Rules
2.12.18 SONET-Related Provisioning Rules
2.12.19 Overhead Circuit Provisioning Rules
2.12.20 Hardware Limitation Rules
Procedures and Provisioning
Note
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This chapter provides TL1 procedures and provisioning for the Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, and Cisco ONS 15600.
•
•
•
•
•
2.1 Setting up TL1 Communication
The period during which a user is logged into the node is called a session. There are three options you can use to open a session (login):
•
•
•
The TL1 password identifier (PID) is masked when accessing a TL1 session using any of these options. When you log out of any of these options, you are closing a session. The ONS 15454 and ONS 15310-CL allow a maximum of 20 (19 Telnet sessions and one craft session) concurrent TL1 sessions using any one or any combination of the options listed above. The ONS 15600 and ONS 15310-MA support a maximum of 20 (18 Telnet sessions and two craft sessions) concurrent TL1 sessions on the customer access panel (CAP). For information about issuing commands to multiple nodes, see the "TL1 Gateway" section.
Use the following procedures to open a TL1 session through the CTC, Telnet, or craft interface. In the procedures, the Activate and Cancel User commands are shown in their input format. For more information about these and other commands and messages, refer to the Cisco ONS SONET TL1 Command Guide.
Open a TL1 Session Through CTC
Step 1
Step 2
Step 3
Step 4
•
•
on the toolbar.
Step 5
Step 6
A TL1 interface window appears. There are three subwindows in the TL1 interface window: Request History, Message Log/Summary Log, and TL1 request. Type commands in the TL1 request window. You will see responses in the Message log window. The Request History window allows you to recall previous commands by double-clicking them.
Step 7
Step 8
ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>;
Step 9
Note
Step 10
CANC-USER:[<TID>]:<USERID>:<CTAG>;
Step 11
Open a TL1 Session Through Telnet
To communicate with the ONS network element (NE) using TL1 commands through a Telnet session over a craft interface or a LAN connection, you can choose from two ports:
•
•
Note
Step 1
Step 2
Telnet <Node IP Address or Node Name> <Port Number> and press Enter.
The Node IP address or Node Name refers to the IP address or Node Name of the node you want to communicate with. Port number is the port (2361 or 3083) where TL1 commands are understood. If the connection is successful, a screen appears with a prompt.
Step 3
ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>;
Note
Step 4
CANC-USER:[<TID>]:<USERID>:<CTAG>;
Open a TL1 Session Through a Craft Interface (Cisco ONS 15454, ONS 15310-CL, and ONS 15310-MA)
The TCC2/TCC2P, XTC, 15310-CL-CTX, and CTX2500 cards have two built-in interface ports for accessing the ONS 15454, ONS 15310-CL, and ONS 15310-MA respectively. With one RJ-45 LAN connection, you can access the system using a standard browser interface. In the browser interface, you can perform local and remote Operation, Administration, Maintenance, and Provisioning (OAM&P) functions and open a VT100 emulation window to enter TL1 commands. If a browser is not available, you can access the system using a nine-pin EIA/TIA-232 port. The EIA/TIA-232 port supports VT100 emulation such that TL1 commands can be entered directly without a browser. The ONS 15310-MA has two EIA/TIA-232 ports.
Step 1
Step 2
•
•
•
•
•
Step 3
Step 4
ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>;
Note
Step 5
CANC-USER:[<TID>]:<USERID>:<CTAG>;
Open a TL1 Session Through a Craft Interface (Cisco ONS 15600)
The TSC card has one RJ-45 port of the faceplate. The RJ-45 port allows you to access the system using a standard web browser. You must use the RJ-45 port on the active TSC. While using the web browser, you can perform local and remote OAM&P functions.
If a browser is not available, you can access the system using one of the two EIA/TIA-232 ports on the CAP. Each EIA/TIA-232 port supports VT100 emulation so that you can enter TL1 commands directly without using a web browser. Each EIA/TIA-232 port supports its own TL1 session.
Because the CAP EIA/TIA-232 port is set up as a data terminal equipment (DTE) interface, you must use a 3-pair swapping null modem adapter so that the TXD/RXC, DSR/DTR, and CTS/RTS pins are swapped when connecting to the serial ports. The null modem adapter connects the CAP EIA/TIA-232 port (male configuration) and the serial cable (female configuration). Table 2-1 lists the null modem adapter pin assignments.
Table 2-1 Null Modem Adapter Pin Assignments
NC1
1
NC
RXD
2
3
TXD
3
2
DTR
4
6
GND
5
5
DSR
6
4
RTS
7
8
CTS
8
7
NC
9
NC
1 NC = not connected
Step 1
Step 2
Step 3
•
–
–
–
–
–
•
tip -9600 /dev/ttyb
Note
Step 4
Step 5
ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>;
Note
Step 6
CANC-USER:[<TID>]:<USERID>:<CTAG>;
2.2 Test Access
Note
Note
The test access (TACC) feature allows a third-party Broadband Remote Test Unit (BRTU) to create nonintrusive test access points (TAPs) to monitor the circuits on the ONS 15454, ONS 15310-MA, and ONS 15600 for errors. The test access feature also allows the circuit to be split (intrusive), so that the transmission paths can be tested for bit errors through the use of various bit test patterns. The two BRTUs supported by the ONS 15454, ONS 15310-MA, and ONS 15600 are the Hekimian/Spirent BRTU-93 (6750) and the TTC/Acterna Centest 650.
The test access functionality provides TL1 commands for creating and deleting TAPs, connecting or disconnecting TAPs to circuit cross-connects, and changing the mode of test access on the ONS 15454, ONS 15310-MA, and ONS 15600. To view test access information in CTC, in node view click the Maintenance > Test Access tabs.
Refer to Telcordia document GR-834-CORE, Network Maintenance: Access and Testing and GR-1402-CORE, Network Maintenance: Access Testing - DS3 HCDS TSC/RTU and DTAU Functional Requirements for more information about test access.
A TAP provides the capability of connecting the circuit under test to a BRTU. This connection initially provides in-service monitoring capability to permit the tester to determine that the circuit under test is idle. The monitor connection should not disturb the circuit under test. The access point and remote test unit (RTU) also provide the capability of splitting a circuit under test. A split consists of breaking the transmission path of the circuit under test. This is done out of service. The two sides of the access point are called the Equipment (E) and Facility (F) directions. For a 4-wire or 6-wire circuit, the transmission pairs within the access point are defined as the A and B pairs. The circuit under test should be wired into the access point so that the direction of transmission on the A pair is from E to F, and the transmission direction for the B pair is from F to E ( Figure 2-1).
Figure 2-1 Circuit With No Access Dual FAD TAP
A dual facility access digroup (FAD) TAP uses twice the bandwidth of the circuit under test. This can be specified by the TAPTYPE parameter as shown in the ED-<MOD2> command syntax in the "TAP Creation and Deletion" section. The values are SINGLE and DUAL. It defaults to DUAL.
A single FAD TAP uses half the bandwidth as that of the dual FAD, that is, it uses the same bandwidth as the circuit accessed for the TAP creation. This can be specified by the TAPTYPE parameter as shown in the "TAP Creation and Deletion" section. The values are SINGLE and DUAL. The MONEF, SPLTAB, and SPLTEF modes are not supported by single FAD TAPs ( Figure 2-2).
Figure 2-2 Circuit With No Access Single FAD TAP
2.2.1 Test Access Terminology
The terminology in Table 2-2 is used in conjunction with test access.
The following path naming conventions apply to test access:
•
•
•
•
2.2.2 TAP Creation and Deletion
TL1 supports commands to create, delete, connect, change, retrieve, and disconnect TAPs.
2.2.2.1 ED-<rr>
The edit command (ED-<rr>) is used to change an existing port, synchronous transport signal (STS), or Virtual Tributary (VT) to a TAP.
Note
Input Format:
ED-(T1, T3, STS1, STS3c, STS6c, STS9c, STS12c, STS24c, STS48c, STS192c, VT1, DS1):[<TID>]:<AID>:<CTAG>[:::TACC=<TACC>][TAPTYPE=<TAPTYPE>];
Edit an existing port, STS, or VT and change it to a TAP so it can be used when requesting TACC connections. Includes a new optical parameter, TACC=n, that defines the port, STS, or VT as a TAP with a selected unique TAP number. This TAP number will be used when requesting test access connections to circuit cross-connections under test. The TAP creation will fail if there is a cross-connection already on the port, STS, or VT.
Note
•
•
The following list applies to TAP numbers:
•
•
•
2.2.2.2 ED-T1
When the ED-T1 command is issued with a specified TACC value for a given T1 port/facility, a dual facility access group (DFAD) is created by using the specified port/facility and the consecutive port/facility.
The command in Example 2-1 creates a DFAD on FAC-1-1 and FAC-1-2.
Example 2-1 Create a DFAD on FAC-1-1 and FAC-1-2
ED-T1::FAC-1-1:12:::TACC=1; DV9-99 1970-01-02 03:16:11 M 12 COMPLD ;
Note
2.2.2.3 ED-T3
When the ED-T3 command is issued with a specified TACC value for a given T3 port/facility, a DFAD is created by using the specified port/facility and the consecutive port/facility.
The command in Example 2-2 creates a T3 DFAD on FAC-2-1 and FAC-2-2.
Example 2-2 Create a T3 DFAD on FAC-2-1 and FAC-2-2
ED-T3::FAC-2-1:12:::TACC=2; DV9-99 1970-01-02 03:16:11 M 12 COMPLD ;
Note
2.2.2.4 ED-DS1
When the ED-DS1 command is issued with a specified TACC value for a given DS1 facility on a DS3XM card, a DFAD is created by using the specified facility and the consecutive port/facility.
The command in Example 2-3 creates DFAD on DS1-2-1-1 and DS1-2-1-2.
Example 2-3 Create a DFAD on DS1-2-1-1 and DS1-2-1-2
ED-DS1::DS1-2-1-1:12:::TACC=3; DV9-99 1970-01-02 03:16:11 M 12 COMPLD ;
Note
2.2.2.5 ED-STSn
When the ED-STSn command is issued for a TACC, it assigns the STS for the first two-way test access connection and STS+1 as the second two-way connection. For STS3c, STS9c, STS12c, STS24c, and STS48c, the next consecutive STS of same width is chosen. The TAP creation will fail if either of the consecutive STSs are not available.
The command in Example 2-4 creates a TAP on STS-5-1 and STS-5-2.
Example 2-4 Create a TAP on STS-5-1 and STS-5-2
ED-STS1::STS-5-1:12:::TACCC=4 DV9-99 1970-01-02 03:16:11 M 12 COMPLD ;
Note
The command in Example 2-5 creates an STS24c dual TAP on STS-6-1 and STS-6-25.
Example 2-5 Create an STS24c Dual TAP on STS-6-1 and STS-6-25
ED-STS24C::STS-6-1:12:::TACC=5: DV9-99 1970-01-02 03:16:11 M 12 COMPLD ;
Note
2.2.2.6 ED-VT1
When the ED-VT1 command is issued for a TACC, a VT TAP is created. The specified VT access identifier (AID) is taken as the first VT connection. The second VT connection is made by incrementing the VT group and keeping the VT number the same.
The command in Example 2-6 creates a VT TAP on VT1-1-1-1-1 and VT1-1-1-2-1.
Example 2-6 Create a VT TAP on VT1-1-1-1-1 and VT1-1-1-2-1
ED-VT1-1-1-1-1:12:::TACC=6; DV9-99 1970-01-02 03:16:11 M 12 COMPLD ;
Note
2.2.3 Connect Test Access Points
The connect test access points command (CONN-TACC-<rr>) is used to make a connection between the TAP and the circuit or cross-connect under test.
Note
Input Format:
CONN-TACC-(T1, T3, STS1, STS3C, STS6C, STS9C, STS12C, STS24C, STS48C, STS192c, VT1,DS1):[<TID>]:<AID>:<CTAG>::<TAP>:MD=<MD>;
Connect the port, STS, or VT defined by <AID> to the port, STS, or VT defined by the <TAP> number. The mode of test access to the circuit or cross-connect is specified by <MD>. The mode can be either monitor (nonintrusive), split (intrusive), or loop (intrusive) mode. The various modes are described in the "Test Access Mode Definitions" section.
Note
Note
The following error codes are supported:
•
•
•
•
•
•
•
The command in Example 2-7 creates a connection between TAP number one and the port/facility FAC-1-3 with the access mode defined as MONE. The various modes are described in the "Test Access Mode Definitions" section.
Example 2-7 Create a Connection Between TAP 1 and FAC-1-3
CONN-TACC-T1::FAC-1-3:12::1:MD=MONE; DV9-99 1970-01-02 02:51:54 M 12 COMPLD 1 ;2.2.4 Change Access Mode
The change access mode command (CHG-ACCMD-<rr>) is used to change the access mode.
Note
Input Format:
CHG-ACCMD-(T1, T3, STS1, STS3C, STS6C, STS9C, STS12C, STS24C, STS48C, STS192c, VT1, DS1):[<TID>]:<TAP>:<CTAG>::<MD>;
Use this command to change the type of test access. This might be a change from monitoring the data to inserting data into the STS. This command can only be applied to an existing TAP connection. If a TAP connection does not exist, a RTEN error is returned.
The following error codes are supported:
•
•
•
The command in Example 2-8 changes the access mode of TAP 1 to LOOPE.
Example 2-8 Change TAP 1 Access Mode to LOOPE
CHG-ACCMD-T1::1:12::LOOPE; DV9-9 1970-01-02 02:59:43 M 12 COMPLD ;
Note
Note
2.2.5 Retrieve Test Access Point Information
The following sections retrieve TAP information using the RTRV-<rr> and RTRV-TACC commands. Refer to the Cisco ONS SONET TL1 Command Guide for specific command formats and examples.
2.2.5.1 RTRV-<rr>
The RTRV-<rr> command retrieves TAP information.
Note
Note
Input Format:
RTRV-(T1, T3, STS1, STS3C, STS6C, STS9C, STS12C, STS24C, STS48C, STS192c, VT1, DS1):[<TID>]:<AID>:<CTAG>;
This command is modified to include the return of a TAP number if the requested <AID> is defined as a TAP. An optional TACC=<TAPNUMBER> will appear in the output list if the requested <AID> is defined as a TAP. The example in Example 2-9 retrieves TAP information for FAC-1-1.
Example 2-9 Retrieve TAP Information for FAC-1-1
RTRV-T1::FAC-1-1:12; dv9-99 1970-01-02 02:49:16 M 12 COMPLD "FAC-1-1::LINECDE=AMI,FMT=D4,LBO=0-131,TACC=1,TAPTYPE=DUAL:OOS" ;2.2.5.2 RTRV-TACC
The RTRV-TACC command can also be used to retrieve details associated with a TAP.
Input Format:
RTRV-TACC:[<TID>]:<TAP>:<CTAG>;
The TAP is identified by the TAP number. The ALL input TAP value means that the command will return all the configured TACCs in the NE. An example of the RTRV-TACC command is provided in Example 2-10.
Example 2-10 Retrieve Details for TAP 241
RTRV-TACC:CISCO:241:CTAG; TID-000 1998-06-20 14:30:00 M 001 COMPLD "241:STS-2-1-1.STS-2-2,MONE,STS-12-1-1,STS-13-1-1" ;2.2.6 Disconnect Test Access Points
TAPs can be disconnected in the following ways:
•
•
•
•
The disconnect TAP (DISC-TACC) command disconnects the TAP and puts the connection back to its original state (no access).
Input Format:
DISC-TACC:[<TID>]:<TAP>:<CTAG>;
The command in Example 2-11 disconnects TAP 1 from the circuit/cross-connect under test.
Example 2-11 Disconnect TAP 1 from the Circuit/Cross-Connect Under Test
DISC-TACC::1:12; DV9-99 1970-01-02 02:59:43 M 12 COMPLD ;
Note
The following error codes are supported:
•
•
2.2.7 Delete Test Access Points
To delete a TAP, issue the edit TAP command with the TACC set to zero.
Input Format:
ED-<STS_PATH>:[<[TID>]:<AID>:<CTAG>:::TACC=0:;
Note
Note
2.2.8 Test Access Configurations
This section shows single node ( Figure 2-3) and multinode ( Figure 2-4) test access configurations.
Use the following commands to configure test access:
Step 1
This command changes STS1 and STS2 on Slot 1 to a TAP. The CTAG is 90. It sets the TACC number to 1.
Step 2
This command connects the <AID> to the TACC defined by TAP 1 on the E side. The CTAG is 91.
Note
Figure 2-3 Single Node View (Node 1)
In the Figure 2-3 configuration, there might be a single DS-3 port wired up, configured as 14 dual FADs (28 VTs).
Figure 2-4 Multinode View (MONE Example)
The following commands are performed on NE3:
ENT-CRS-STS1::<AID I-G>:100::2WAY;
A connection, not a TAP. CTAG is 100.
ENT-CRS-STS1::<AID J-H>:101::2WAY;
Second connection, not a TAP.
The following commands are performed on NE1:
Assuming the path from A to B is already entered, the A and B points in Figure 2-4 refer to entry and exit points on the node or different cards. The E/F designators refer to the two two-way connections from NE3.
The following command creates a TAP with STS-1-1 and STS-1-2 through NE1. TAP number assigned is 4.
ED-STS1::STS-1-1:TACC=4;
The following command connects TAP 4 to the circuit:
CONN-TACC-STS1::<AID A or B>:102::4:<MD>
Note
2.2.9 Test Access Mode Definitions
The following diagrams show what the different test access modes (<MD>) refer to. Figure 2-5 shows a circuit with no access (dual FAD TAP) and Figure 2-6 shows a circuit with no access (single FAD TAP). The subsections that follow show the circuits in each test access mode. The QRS can be generated by an outside source, for example, the empty connection of the BRTU.
The subsections that follow describe the modes:
MONE, MONF, and MONEF access modes are Non-Service Affecting and can be applied to an In Service (IS) port state.
LOOPE, LOOPF, SPLTE, SPLTF, SPLTEF, SPLTA, SPLTB, and SPLTAB access modes are intrusive and can be applied only to a circuit or /port that is in the Out Of Service, Maintenance (OOS_MT) port state. The NE will change the state of the circuit under test to OOS_MT during the period of TACC and restore it to the original state when the connection between the TAP and the circuit is dropped.
Figure 2-5 Circuit With No Access (Dual FAD TAP)
Figure 2-6 Circuit With No Access (Single FAD TAP)
2.2.9.1 MONE
Monitor E (MONE) mode indicates a monitor connection provided from the FAD to the A transmission path of the accessed circuit ( Figure 2-7 and Figure 2-8). This is a nonintrusive mode.
Figure 2-7 MONE Access Mode Single TAP
Figure 2-8 MONE Access Mode Dual TAP
2.2.9.2 MONF
Monitor F (MONF) mode indicates that the FAD is providing a monitor connection to the B transmission path of the accessed circuit ( Figure 2-9 and Figure 2-10). This is a nonintrusive mode.
Figure 2-9 MONF Access Mode Single TAP
Figure 2-10 MONF Access Mode Dual TAP
Note
2.2.9.3 MONEF
Monitor EF (MONEF) mode is a monitor connection provided from the FAD1 (odd pair) to a DFAD, to the A transmission path, and from FAD2 (even pair) of the same DFAD, to the B transmission path of the accessed circuit. This is a nonintrusive mode ( Figure 2-11).
MONEF mode for T3 (DS3 high capacity digital service [HCDS]) indicates that the odd pair of an FAP is providing a monitor connection to the A transmission path and from the even pair of an FAP to the B transmission path of the accessed circuit.
Figure 2-11 MONEF Access Mode Dual TAP
2.2.9.4 SPLTE
Split E (SPLTE) mode splits both the A and B paths and connects the E side of the accessed circuit to the FAD ( Figure 2-12 and Figure 2-13).
Note
Figure 2-12 SPLTE Access Mode Single TAP
Figure 2-13 SPLTE Access Mode Dual TAP
2.2.9.5 SPLTF
Split F (SPLTF) mode splits both the A and B paths and connects the F side of the accessed circuit to the FAD ( Figure 2-14 and Figure 2-15).
Note
Figure 2-14 SPLTF Access Mode Single TAP
Figure 2-15 SPLTF Access Mode Dual TAP
2.2.9.6 SPLTEF
Split EF (SPLTEF) mode for T1 (DS1 HCDS) splits both the A and B paths, connects the E side of the accessed circuit to FAD1 and the DFAD pair, and connects the F side to the FAD2 of the same DFAD pair ( Figure 2-16).
SPLTEF mode for T3 (DS3 HCDS) splits both the A and B paths and connects the E side of the accessed circuit to the odd pair of the FAP and the F side to the even pair of the FAP.
Figure 2-16 SPLTEF Access Mode Dual TAP
2.2.9.7 LOOPE
Loop E (LOOPE) mode splits both the A and B paths, connects the incoming line from the E direction to the outgoing line in the E direction, and connects this looped configuration to the FAD ( Figure 2-17 and Figure 2-18). Loop E and F modes are basically identical to the SPLT E and F modes except that the outgoing signal is the incoming signal and not the signal from the remote test unit (RTU).
Note
Figure 2-17 LOOPE Access Mode Single TAP
Figure 2-18 LOOPE Access Mode Dual TAP
2.2.9.8 LOOPF
Loop F (LOOPF) mode splits both the A and B paths, connects the incoming line from the F direction to the outgoing line in the F direction and connects this looped configuration to the FAD ( Figure 2-19 and Figure 2-20).
Note
Figure 2-19 LOOPF Access Mode Single TAP
Figure 2-20 LOOPF Access Mode Dual TAP
2.2.9.9 SPLTA
Split A (SPLTA) mode indicates that a connection is provided from both the E and F sides of the A transmission path of the circuit under test to the FAD and splits the A transmission path ( Figure 2-21 and Figure 2-22). This mode is similar to the SPLTE and SPLTF modes, except the signals are sent to the RTU, not the NE signal configuration.
Figure 2-21 SPLTA Access Mode Single TAP
Figure 2-22 SPLTA Access Mode Dual TAP
2.2.9.10 SPLTB
Split B (SPLTB) mode indicates that a connection is provided from both the E and F sides of the B transmission path of the circuit under test to the FAD and splits the B transmission path ( Figure 2-23 and Figure 2-24).
Figure 2-23 SPLTB Access Mode Single TAP
Figure 2-24 SPLTB Access Mode Dual TAP
2.2.10 Unmapped AID Test Access Point Connections
The ONS 15454 and ONS 15600 support connections to unmapped AIDs (unmapped circuits). The TAPs can be connected to an unmapped AID, for example, an AID that does not have a cross-connect on it. The access modes supported are: MONE, SPLTE, and LOOPE.
Example 2-12 creates a TAP on STS-5-1 and STS-5-2.
Example 2-12 Create a TAP on STS-5-1 and STS-5-2
ED-STS1::STS-5-1:12:::TACC=1; DV9-99 1970-01-02 03:16:11 M 12 COMPLD ;Example 2-13 creates an unmapped AID connection with the MONE access mode.
Example 2-13 Create an Unmapped AID Connection with the MONE Access Mode
CONN-TACC-STS1::STS-5-3:12::1:MD=MONE; DV9-99 1970-01-02 02:51:54 M 12 COMPLD 1 ;
Note
Note
Note
2.2.10.1 One-Way Circuit
The examples in this section assume that an STS TAP is already created with a TAP number of 1.
ENT-CRS-STS1::STS-5-1,STS-5-2:12::1WAY;
DV9-99 1970-07-01 20:29:06
M 12 COMPLD;CONN-TACC-STS1::STS-5-1:12::1:MD=MONF;
DV9-99 1970-01-01 20:29:47
M 12 DENY
EANS
STS-5-1
/*INCORRECT TAP MODE*/The <AID> specified in the above CONN-TACC command is the source AID for the one-way circuit. In this case, only MONE and SPLTA modes are allowed because there is no B path in the case of a one-way circuit (see Table 2-3).
CONN-TACC-STS1::STS-5-1:12::1:MD=MONE;
DV9-99 1970-01-01 20:30:09
M 12 COMPLDDISC-TACC::1:12;
DV9-99 1970-01-01 20:30:20
M 12 COMPLD
;However, if the AID specified is the destination AID, as shown below, the modes allowed are MONF and SPLTB.
CONN-TACC-STS1::STS-5-2:12::1:MD=MONF;
DV9-99 1970-01-01 20:30:32
M 12 COMPLD
Note
•
2.2.10.2 Two-Way Circuits
For two-way circuits, all the modes are allowed, as shown in Table 2-3. The same applies for UPSR_UPSR and path protection circuit types. In the case of UPSR_UPSR and path protection circuits, the working path is connected irrespective of which path is currently active.
2.2.10.3 Unmapped AID
As explained in the "Unmapped AID Test Access Point Connections" section, connections can be made to an AID without a cross-connect on it. The modes supported are MONE, SPLTE, and LOOPE, as shown in Table 2-3.
Note
Table 2-3 Modes Supported by Circuit Type
1-way (from E)1
X
—
—
—
—
—
—
—
X
—
1-way (from F)2
X
—
—
—
—
—
—
—
X
2-way
X
X
X
X
X
X
X
X
X
X
Path Protection
X
X
X
X
X
X
X
X
X
X
UPSR_HEAD (from E)
X
—
—
—
—
—
—
—
X
UPSR_HEAD (from F)
—
X
—
—
—
—
—
—
—
X
UPSR_DROP
UPSR_DC
UPSR_EN
(from E)X
—
—
—
—
—
—
—
X
—
UPSR_DROP
_DC
UPSR_EN
(from F)—
X
—
—
—
—
—
—
—
X
UPSR_UPSR
X
X
X
X
X
X
X
X
X
X
Unmapped AID
X
—
—
X
—
—
X
—
—
—
1 If the AID specified is the source AID, the direction is designated as "from E" in all one-way circuits (1-way, UPSR_HEAD, UPSR_DROP,UPSR_DC, and UPSR_EN).
2 If the AID specified is the destination AID or the drop side, the direction is designated as "from F" in all one-way circuits (1-way, UPSR_HEAD, UPSR_DROP,UPSR_DC, and UPSR_EN).
2.3 TL1 Gateway
This section describes the TL1 gateway and provides procedures and examples for implementing TL1 gateway on the ONS 15454, ONS 15310-CL, ONS 15310-MA, and ONS 15600.
2.3.1 Gateway Network Element Topology
You can issue TL1 commands to multiple nodes through a single connection using the TL1 gateway. Any node can serve as a Gateway Network Element (GNE), End Network Element (ENE), or Intermediate Network Element (INE). A node becomes a GNE when a TL1 user connects to it and enters a command destined for another node. An ENE is an end node because it processes a TL1 command that is passed to it from another node. An INE is an intermediate node because of topology; it has no special hardware, software, or provisioning.
To implement the TL1 gateway, use the desired ENE's TID in the ACT-USER command to initiate a session between the GNE and the ENE. After a session is established, you need to enter the ENE's TID in all of the subsequent commands that are destined for the ENE. From the GNE, you can access several remote nodes, which become the ENEs. The ENEs are the message destinations or origins. The INE handles the data communications channel (DCC) TCP/IP packet exchange.
The GNE Session is the connection that multiplexes TL1 messages between the operations support system (OSS)/craftsperson and the GNE. The GNE demulitplexes incoming OSS TL1 commands and forwards them to the remote ENE. The GNE also multiplexes incoming responses and autonomous messages to the GNE Session. The ENE Session is the connection that exchanges messages between the GNE and the remote ENE. Figure 2-25 shows the GNE topology.
Figure 2-25 Example of a GNE Topology
2.3.2 ONS 15454, ONS 15310-CL, and ONS 15310-MA Gateway
With the TCC2/TCC2P card on an ONS 15454, each GNE can support twenty (19+1) concurrent gateway communication sessions (connections from an OS to the GNE). Nineteen of these sessions are via the LAN (wire-wrap, active TCC2/TCC2P LAN port, or DCC) and the twentieth session is reserved for the active TCC2/TCC2P serial port. With the XTC card on an ONS 15310-CL, and the CTX2500 on the ONS 15310-MA, each GNE can support six (5+1) concurrent gateway communication sessions. Five of these sessions are through the LAN (wire wrap, active XTC/15310-CL-CTX/XTC2500 LAN port or DCC) and the sixth session is reserved for the active XTC/15310-CL-CTX/XTC2500 serial port.
Each GNE can support 11 (TCC2/TCC2P) or 6 (XTC/15310-CL-CTX/XTC2500) concurrent communication gateway sessions and up to a maximum of 176 (TCC2/TCC2P) or 96 (XTC/15310-CL-CTX/CTX2500) ENEs/GNE. You can dynamically distribute the ENEs to balance the number of concurrent gateway communication sessions versus the number of NEs on the DCC. The GNE treats the 11 (10+1 for TCC2/TCC2P) or 6 (5+1 for XTC/15310-CL-CTX/CTX2500) concurrent gateway communication sessions and the 176 (TCC2/TCC2P) or 96 (XTC/15310-CL-CTX/CTX2500) ENE/GNE limit as a resource pool ( Table 2-4) and continues to allocate resources until the pool is exhausted (see Table 2-5 for allocation examples). When the pool is exhausted, the GNE returns an "All Gateways in Use" message or an "All ENE Connections in Use" message.
2.3.3 ONS 15600 Gateway
Each GNE can support 20 concurrent gateway communication sessions (connections from an OS to the GNE), available through the LAN (CAP, TSC, or DCC). The GNE can support 18 Telnet sessions and 2 serial port sessions. The gateway resource pools for each platform are shown in Table 2-4. Examples of GNE/ENE resource alocation are provided in Table 2-5.
Note
Note
2.3.4 Implementing TL1 Gateway
The following procedures demonstrate TL1 gateway on a four-node ring (without TL1 gateway in Figure 2-26 and with TL1 gateway in Figure 2-27), where:
•
•
•
•
Figure 2-26 Four-Node Ring Without TL1 Gateway
Figure 2-27 Four-Node Ring With TL1 Gateway
Log Into a Remote ENE
Step 1
Step 2
ACT-USER:NODE1:USERNAME:1234:PASSWORD;
The GNE forwards the login to ENE 1. After successful login, ENE 1 sends a COMPLD response.
Step 3
ACT-USER:NODE3:USERNAME:1234:PASSWORD;
The GNE forwards the login to ENE 3. After successful login, the ENE 3 sends a COMPLD response.
Forward Commands by Specifying the ENE TID (Node 1 or Node 3)
When you are logged into ENE 1 and ENE 3, enter a command and designate a specific TID. To retrieve the header of Node 1, enter the following command:
RTRV-HDR:NODE1::1;
To retrieve the header of Node 3, enter the following command:
RTRV-HDR:NODE3::3;
Receive Autonomous Messages from the Remote ENE
To receive autonomous messages from the remote ENE, you must log into the remote ENE. When you are logged in, you will begin to receive autonomous messages. The source of the message is identified in the header of the message.
Log Out of a Remote ENE
To disconnect from a remote ENE, you must use the CANC-USER command. Use the following command to disconnect from ENE 1:
CANC-USER:NODE1:USERNAME:1;
Use the following command to disconnect from ENE 3:
CANC-USER:NODE3:USERNAME:3;
The GNE forwards the logout to the remote ENEs. The GNE/ENE TCP session is closed.
2.4 Ring Provisioning
This section provides information and sample procedures for setting up STS or VT circuits over existing path protection and bidirectional line switch ring (BLSR) configurations using TL1, including:
•
•
•
•
For VTs, add the normal VT Group and VT ID extensions. These examples also assume that the slots/ports have been autoprovisioned (through a plug-in event) and that the ports involved have been placed into the IS state using a port configuration command, for example, ED-OCN.
Note
Note
2.5 PCA Provisioning
You can provision or retrieve protection channel access (PCA) cross-connections on two-fiber and four-fiber BLSR topologies at these supported OC rates: OC-12 (two-fiber only), OC-48, and OC-192. The traffic on the protection channel is referred to as extra traffic and has the lowest priority level. Extra traffic will be preempted by any working traffic that requires the use of the protection channel.
In a two-fiber BLSR, the extra traffic is provisioned on the upper half of the bandwidth path. In a four-fiber BLSR, the extra traffic is provisioned on the protect fiber. The PCA provisioning feature allows you to establish the PCA cross-connection on the protection path of the two-fiber BLSR and the protection channel of the four-fiber BLSR only when the query is an explicit request.
There are two PCA connection types: 1WAYPCA and 2WAYPCA. The PCA cross-connection is provisioned only when the user provides an explicit request using the ENT-CRS-STSp/VT1 commands. If the cross-connection is a PCA cross-connection, either 1WAYPCA or 2WAYPCA is shown in the cross-connect type field of the RTRV-CRS-STSp/VT1 command output.
1WAYPCA and 2WAYPCA are only used in the TL1 user interface to provide usability and visibility for the user to specify a PCA cross-connection type in the TL1 cross-connection commands.
The following restrictions apply to PCA provisioning:
•
•
•
•
2.5.1 Provision a PCA Cross-Connection
Example 2-14 shows the input format for provisioning a PCA cross-connection.
Example 2-14 Provision a PCA Cross-Connect: Input Format
ENT-CRS-<PATH>:[<TID>]:<FROM>,<TO>:<CTAG>::[<CCT>][::]; <PATH>::={STS_PATH, VT1} [<CCT>]::={1WAY, 1WAYDC, 1WAYEN, 2WAY, 1WAYPCA, 2WAYPCA}, {STS_PATH}::={STS1, STS3C, STS6C, STS9C, STS12C, STS24C, STS48C, STS192C}Where:
•
•
•
Example 2-15 shows an input example of provisioning an STS3C PCA cross-connection.
Example 2-15 Provision a PCA Cross-Connect: Example
ENT-CRS-STS3C::STS-1-1,STS-2-1:123::2WAYPCA;
Note
Note
2.5.2 Retrieve a PCA Cross-Connection
Use the input format in Example 2-16 to retrieve a PCA cross-connection.
Example 2-16 Retrieve a PCA Cross-Connect: Input Format
RTRV-CRS-[<PATH>]:[<TID>]:<AID>:<CTAG>[::::];<PATH>::={STS_PATH, VT1, STS}If PATH is STS, it will retrieve all the STS cross-connections based on the queried AIDs.
<AID>={FacilityAIDs, STSAIDs, VTAIDs, ALL}
Example 2-17 shows the output format of the PCA STSp cross-connection retrieval command.
Example 2-17 Output Format of PCA STSp Cross-Connect Retrieve Command
"<FROM>,<TO>:2WAYPCA,STS3C"Example 2-18 shows the output format of the PCA VT cross-connection retrieval command.
Example 2-18 Output Format of PCA VT Cross-Connect Retrieve Command
"<FROM>,<TO>:2WAYPCA"2.6 FTP Software Download
Note
The file transfer protocol (FTP) software download feature downloads a software package to the inactive flash partition residing on either the TCC2/TCC2P, XTC, 15310-CL-CTX, CTX2500, or TSC card. FTP software download provides for simplex and duplex TCC2/TCC2P, XTC, 15310-CL-CTX, CTX2500, or TSC card downloads, success and failure status, and in-progress status at 20 percent increments.
2.6.1 COPY-RFILE
The COPY-RFILE command downloads a new software package from the location specified by the FTP URL into the inactive flash partition residing on either the TCC2/TCC2P, XTC,15310-CL-CTX, CTX2500, or TSC card. COPY-RFILE can also be used to backup and restore the database file.
Note
Input format:
COPY-RFILE:[<TID>]:[<SRC>]:<CTAG>::TYPE=<XFERTYPE>,[SRC=<SRC1>,]
[DEST=<DEST>,][OVWRT=<OVWRT>];where:
•
•
•
"FTP://FTP_USER[:FTP_PASSWORD]]@FTP_HOST_IP[:FTP_PORT]
/PACKAGE_PATH[:TYPE=I]"where:
–
–
–
–
–
In a firewall environment, the host name should be replaced with a list of IP addresses, each separated by an ampersand (@) character. The first IP address should be for the computer where the package file is stored. Subsequent IP addresses are for firewall computers moving outward toward the edge of the network until the final IP address listed is the computer that outside users use to first access the network.
For example, if your topology is:
"FTPHOST <-> GNE3 <->GNE2 <-> GNE1 <-> ENE"
the FTP URL is:
FTP://FTP_USER:FTP_PASSWORD@FTP_HOST_IP@GNE3@GNE2@GNE1/
PACKAGE_PATH•
•
Note
•
2.6.2 APPLY
The APPLY command can activate or revert software depending on the version of software loaded on the active and protect flash. An error is returned if the node is attempting to activate to an older software load or trying to revert to a newer software load. If this command is successful, the appropriate flash is selected and the TCC2/TCC2P, XTC, 15310-CL-CTX, CTX2500, or TSC card will reboot.
The input format for the APPLY command is as follows:
APPLY:[<TID>]::<CTAG>[::<MEM_SW_TYPE>];
where:
•
2.6.3 REPT EVT FXFR
REPT EVT FXFR is an autonomous message used to report the start, completion, and completed percentage status of the FTP software download. REPT EVT FXFR also reports any failure during the software upgrade including invalid package, invalid path, invalid userid/password, and loss of network connection.
Note
The "BYTES_XFRD" is only sent when the "FXFR_STATUS" is IP or COMPLD.The output format of the REPT EVT FXFR message is as follows:
SID DATE TIME
A ATAG REPT EVT FXFR
"<FILENAME>,<FXFR_STATUS>,[<FXFR_RSLT>],[<BYTES_XFRD>]"
;where:
•
•
•
•
2.6.4 Downloading New Software
The following procedure downloads new software to the TCC2/TCC2P, XTC, 15310-CL-CTX, CTX2500, or TSC card using TL1.
Download New Software
Note
Step 1
Step 2
Step 3
Step 4
Input example:
RTRV-NE-GEN:::1;
The output should be similar to the following:
VA454-94 1970-01-06 22:22:12
M 1 COMPLD
"IPADDR=10.82.87.94,IPMASK=255.255.255.224,DEFRTR=10.82.86.1,
ETHIPADDR=10.82.87.94,ETHIPMASK=255.255.255.224,NAME=VA454-94,
SWER=3.40.00,LOAD=03.40-002G-14.21,PROTSWVER=4.00.00,
PROTLOAD=04.00-X02G-25.07,DEFDESC=\"FACTORY DEFAULTS\""
;Step 5
In Example 2-19, the package is located in "/%2FUSR/CET/VINTARA" in the host 10.77.22.199. The user ID and passwords are TL1 and CISCO454. The directory path of the package is similar to what you will see during an FTP session.
Example 2-19 Issue the COPY-RFILE Command
COPY-RFILE::RFILE- PKG:CTAG::TYPE=SWDL,SRC="FTP://TL1:CISCO454@10.77.29.199 /%2FUSR/CET/VINTARA/15454-0340-X02E-2804.PKG"; DEV208 1970-01-10 11:51:57 M CTAG COMPLD ;Step 6
•
•
•
•
•
•
•
•
•
Example 2-20 REPT EVT FXFR when Node or Host Timed Out During FTP Protocol
DEV208 1970-01-10 11:52:02 A 2816.2816 REPT EVT FXFR "SLOT-11:SFTWDOWN-FAIL,TC,,,,,,,:\"SOFTWARE DOWNLOAD FAILED\",TCC ;Step 7
Example 2-21 REPT EVT FXFR Message Reporting an Active Start
DEV208 1970-01-10 11:52:15 A 2818,2818 REPT EVT FXFR "ACTIVE START" ;Step 8
Example 2-22 SFTDOWN Minor Alarm
DEV208 1970-01--10 11:52:15 * 2817.2817 REPT ALM EQPT "SLOT-7:MN,SFTWDOWN,NSA,,,,:\"SOFTWARE DOWNLOAD IN PROGRESS\",TCC" ;Use the in-progress status at any time during the software download to verify the RTRV-NE-GEN command ( Example 2-23).
Example 2-23 RTRV-NE-GEN Command
RTRV-NE-GEN VA454-94 1970-01-06 22:22;12 M 1 COMPLD "IPADDR=10.82.87.94,IPMASK=255.255.255.224,DEFRTR=10.82.86.1, ETHIPADDR=10.82.87.94,EHTIPMASK=255.255.255.224,NAME=VA454-94, SWVER=3.40.00,LOAD=03.40-002G-14-21,PROTSWVER=NONE, PROTLOAD=DOWNLOADINPROGRESS,DEFDESC=\:FACTORY DEFAULTS\"" ;Step 9
Example 2-24 REPT EVT FXFR Messages During Software Download
DEV208 1970-01-10 11:53:12 A 2820,2820 REPT EVT FXFR "ACTIVE,IP,,20" ;DEV208 1970-01-10 11:53:12 A 2820,2820 REPT EVT FXFR "ACTIVE,IP,,40" ;DEV208 1970-01-10 11:53:12 A 2820,2820 REPT EVT FXFR "ACTIVE,IP,,60" ;DEV208 1970-01-10 11:53:12 A 2820,2820 REPT EVT FXFR "ACTIVE,IP,,80" ;Step 10
Example 2-25 Verifying the PROTLOAD
RTRV-NE-GEN:::1; VA454-94 1970-01-06 22:22:12 M 1 COMPLD "IPADDR=10.82.87.94,IPMASK=255.255.255.224,DEFRTR=10.82.86.1, ETHIPADDR=10.82.87.94,EHTIPMASK=255.255.254.0,NAME=VA454-94, SWVER=3.40.00,LOAD=03.40-002G-14-21,PROTSWVER=4.00.00, PROTLOAD=03.40-X02E-28.04,DEFDESC=\:FACTORY DEFAULTS\"" ;Step 11
Example 2-26 Confirm Download Completion
DEV208 1970-01-10 12:01:16 A 2825,2825 REPT EVT FXFR "ACTIVE,COMPLD,SUCCESS" ;Step 12
Example 2-27 Download is Complete
DEV208 1970-01-10 11:52:15 * 2826,2817 REPT ALM EQPT "SLOT-7:CL,SFTWDOWN,NSA,,,,:\"SOFTWARE DOWNLOAD IN PROGRESS\",TCC" ;2.6.5 Activating New Software
After the software is successfully downloaded, the new software that resides in the protect load must be activated to run on the NE. The APPLY command can be used to activate and revert depending on the version of the protect software and the newly downloaded software (see the "APPLY" section for correct APPLY syntax).
Activate New Software
Step 1
APPLY::1::ACT;
DEV208 1970-01-10 13:40:53
M 1 COMPLD
;An error is reported if a revert is attempted with a newer protect software.
Step 2
CANC-USER::CISCO15:1;
VA454-94 1970-01-07 01:18:18
M 1 COMPLD
;After a successful completion of the APPLY command, the NE will reboot and the TL1 session will disconnect. When the NE comes up after the reboot, it will be running the new software. Traffic switches are possible during activation.
2.6.6 Remote Software Download/Activation Using the GNE
In a network with Section data communications channel (SDCC)-connected ONS 15454s, ONS 15310-CLs, and ONS 15310-MAs, remote download and activation are possible using the GNE/ENE feature supported in TL1. The GNE must be connected by a LAN and the remaining ENEs can download the new software package through fiber from the GNE.
For remote software downloading, complete the steps in the "Download New Software" procedure and the "Activate New Software" procedure, but ensure that the TID in each command is filled with the ENE node name.
Each GNE can support 20 (TCC2/TCC2P) or 6 (XTC, 15310-CL-CTX, CTX2500) concurrent communication gateway sessions and up to a maximum of 176 (TCC2/TCC2P) or 96 (XTC, 15310-CL-CTX, CTX2500) ENEs/GNEs. For more information on TL1 gateway, see the "TL1 Gateway" section.
After activating the nodes ( Example 2-28), five simultaneous software downloads can be initiated using the COPY-RFILE command with appropriate TIDs, as shown in Example 2-29. All downloads will be independent of each other and download speeds might differ.
Example 2-28 Activating the Nodes for Simultaneous Software Downloads
ACT-USER:NODE1:CISCO15:1; ACT-USER:NODE2:CISCO15:1; ACT-USER:NODE3:CISCO15:1; ACT-USER:NODE4:CISCO15:1; ACT-USER:NODE5:CISCO15:1;Example 2-29 Downloading Software on Multiple Nodes Simultaneously
COPY-RFILE:NODE1:RFILE-PKG:CTAG::TYPE=SWDL,SRC="FTP://TL1: CISCO454@10.77.29.199/USR/CET/VINTARA/15454-0340-X02E-2804.PKG"; COPY-RFILE:NODE2:RFILE-PKG... COPY-RFILE:NODE3:RFILE-PKG... COPY-RFILE:NODE4:RFILE-PKG... COPY-RFILE:NODE5:RFILE-PKG...To download software to an ENE through a GNE, the FTTD URL in the COPY-RFILE command must be used as shown in Example 2-30. The FTTD parameter has the following format: "FTTD://USERID:PASSWORD@TL1 GNE NODENAME:21". Prior to Release 6.0, Port 21 is mandatory. In Release 6.0 and later, Port 21 is optional.
Example 2-30 Downloading Software to an ENE through a GNE
GNE = NODE1ENE = NODE2COPY-RFILE:NODE2:RFILE-PKG:1::TYPE=SWDL,SRC=FTP://USER-ID:PASSWORD@HOST-IP//USERS/JDOE/ 15454-XXXX-XXXX-XXXX.PKG,OVWRT=YES,FTTD="FTTD://USERID:PASSWORD@NODE1:21"Individual REPT EVT FXFR messages can be isolated using the node names. RTRV-NE-GEN also requires the individual node names entered in the TID in order to retrieve a specific download status.
Activate the software using the APPLY command ( Example 2-31) on all of the nodes using the GNE node.
Note
Example 2-31 Activate the Software Load
APPLY:NODE1::1::ACT; APPLY:NODE2::1::ACT; APPLY:NODE3::1::ACT; APPLY:NODE4::1::ACT; APPLY:NODE5::1::ACT;2.7 Scheduled PM Report
The scheduled performance monitoring (PM) report is a feature that extends the capability of PM reporting for the Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, and ONS 15600. With a scheduled PM report, the system automatically and periodically generates the PM report of any specified facility or cross-connection.
Note
•
•
•
•
2.7.1 Create a PM Schedule and Receive an Autonomous PM Report
Issue the SCHED-PMREPT-<MOD2> command to create a PM schedule.
Issue the ALW-PMREPT-ALL command to allow the current TL1 session to be able to receive the autonomous PM report.
2.7.2 Manage PM Schedules
Use the following commands to manage PM schedules:
•
•
Note
•
Note
2.7.3 Enable or Disable a TL1 Session to Receive Autonomous PM Reports
Enable a TL1 session to receive a scheduled PM report by issuing the ALW-PMREPT-ALL command.
Note
Disable a TL1 session to receive any scheduled PM report by issuing the INH-PMREPT-ALL command.
2.8 Bridge and Roll
Bridge and Roll functionality in the Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, and ONS 15600 allows live traffic to be moved (rolled) from one entity to another. This section provides information and sample procedures for single-rolling, dual-rolling, and protection rolling for one-way or two-way circuits using TL1 commands, including:
•
•
•
There are two roll modes:
•
•
Caution
Caution
Note
2.8.1 Restrictions
The following restrictions apply for bridge and roll using TL1 in this release:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Note
•
Note
•
Note
•
The following restrictions apply for bridge and roll using TL1 VCAT in this release:
•
•
The following restrictions apply for bridge and roll using TL1 common-fiber-routed VCAT circuits in this release:
•
•
2.8.2 Bridge and Roll TL1 Commands
The following commands are used for bridge and roll. Refer to the Cisco ONS SONET TL1 Command Guide for full command descriptions including input and output formats and examples.
•
This command deletes or completes an attempted rolling operation. This command supports Line-level rolling and bulk rolling. It cannot be used for Path-level rolling. The rolls that are created using the ENT-BULKROLL-<OCN_TYPE> command can be deleted using the DLT-BULKROLL-<OCN_TYPE> command.
•
This command deletes an attempted rolling operation or completes an attempted rolling operation.
•
This command edits information about rolling traffic from one endpoint to another without interrupting service. This command can use the CMDMDE option to force a valid signal. The only parameter that can be edited is CMDMDE. The time slots cannot be edited. This commands supports Line-level rolling and bulk rolling. It cannot be used for Path-level rolling.
•
This command edits information about rolling traffic from one endpoint to another without interrupting service. This command can use the CMDMDE option to force a valid signal. The only parameter that can be edited is CMDMDE. The time slots cannot be edited.
•
This command enters information about rolling traffic from one endpoint to another without interrupting service. This commands supports Line-level and bulk rolling. It cannot be used for single Path-level rolling.
•
This command enters information about rolling traffic from one endpoint to another without interrupting service. This command supports STS and VT Path-level rolling only.
•
This command retrieves roll data parameters. This command supports Line-level rolling and bulk rolling. It cannot be used for Path-level rolling.
•
This command retrieves roll data parameters.
2.8.3 Two-Way Circuit Single Roll and Dual Roll Procedures
Single roll operation moves either the source or destination of a circuit to a new endpoint: onto the same node or onto a different node. In a single-roll operation, you only choose one roll point during the process.
Dual roll operation reroutes a segment between two roll points of a circuit. The new route can be one of the following:
•
•
In dual roll operation, you choose two roll points during the process.
Create a Two-Way Circuit Single Roll or Dual Roll
To create a two-way circuit single roll or dual roll, enter the ENT-ROLL-<MOD_PATH> command or the ENT-BULKROLL-<OCN_TYPE> command depending on the type of roll you want to perform.
The input formats are as follows:
•
RTO=<RTO>,RMODE=<RMODE>,[CMDMDE=<CMDMDE>];•
RTOSTART=<RTOSTART>,[RFROMSTART=<RFROMSTART>],
[RFROMEND=<RFROMEND>],RMODE=<RMODE>,[CMDMDE=<CMDMDE>];
Step 1
•
ENT-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::RFROM=STS-2-1-1,
RTO=STS-3-1-1,RMODE=AUTO,CMDMDE=FRCD;•
ENT-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::RFROM=STS-2-1-1,
RTO=STS-3-1-1,RMODE=MAN,CMDMDE=FRCD;•
ENT-BULKROLL-OC48:CISCO:FAC-5-1:123:::RFROMSTART=STS-5-1-1,
RTOSTART=STS-6-1-1,RMODE=AUTO,CMDMDE=FRCD;This command will roll all the STS and VT paths to a facility on Slot 6 with the same STS as shown in Table 2-6.
•
ENT-BULKROLL-OC48:CISCO:FAC-5-1:123:::RFROMSTART=STS-5-1-1,
RTOSTART=STS-6-1-1,RFROMEND=STS-5-1-4,RMODE=AUTO,CMDMDE=FRCD;This command will roll the paths shown in Table 2-7.
Step 2
Input format:
RTRV-BULKROLL-<OCN_TYPE>:[<TID>]:<SRC>:<CTAG>;
Input example:
RTRV-BULKROLL-OC12:CISCO:FAC-3-1:1;
2.8.4 One-Way Circuit Single Roll and Dual Roll Procedures
Single roll operation moves either the source or destination of a circuit to a new endpoint: onto the same node or onto a different node. In single roll operation, you only choose one roll point during the process.
Dual roll operation reroutes a segment between two roll points of a circuit. In dual roll operation, you choose two roll points during the process.The new route can be one of the following:
•
•
Create a One-Way Circuit Single Roll
To create a one-way circuit single roll, enter the ENT-ROLL-<MOD_PATH> command or the ENT-BULKROLL-<OCN_TYPE> command depending on the type of roll you want to perform.
Input formats:
•
RTO=<RTO>,RMODE=<RMODE>,[CMDMDE=<CMDMDE>];
Note
•
RTOSTART=<RTOSTART>,[RFROMSTART=<RFROMSTART>],
[RFROMEND=<RFROMEND>],RMODE=<RMODE>,[CMDMDE=<CMDMDE>];
Step 1
•
ENT-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::RFROM=STS-2-1-1,
RTO=STS-3-1-1,RMODE=AUTO,CMDMDE=FRCD;•
ENT-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::RFROM=STS-2-1-1,
RTO=STS-3-1-1,RMODE=MAN,CMDMDE=FRCD;•
ENT-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::RFROM=STS-2-1-1,
RTO=STS-3-1-1,RMODE=AUTO,CMDMDE=FRCD;This command will roll all the STS and VT paths to a facility on Slot 6 with the same STS as shown in Table 2-8.
•
ENT-BULKROLL-OC48:CISCO:FAC-5-1:123:::RTOSTART=STS-6-1-1,
RFROMSTART=STS-5-1-1,RFROMEND=STS-5-1-4,RMODE=AUTO,CMDMDE=FRCD;This command will roll the paths shown in Table 2-9.
Step 2
Input format:
RTRV-BULKROLL-<OCN_TYPE>:[<TID>]:<SRC>:<CTAG>;
Input example:
RTRV-BULKROLL-OC12:CISCO:FAC-3-1:1;
Create a One-Way Circuit Dual Roll
In this procedure, both the source and destination nodes are rolled. There are two types of dual rolls:
•
•
Step 1
Step 2
2.8.5 Protection Rolling Procedures
To perform protection rolls, follow the procedures in the "Two-Way Circuit Single Roll and Dual Roll Procedures" section and the "One-Way Circuit Single Roll and Dual Roll Procedures" section.
Note
Table 2-10 shows what kind of protection rolls are supported from one domain to another. An X indicates the roll is allowed. A dash indicates that the roll is not allowed.
2.9 1:N Low-Density to 1:N High-Density Upgrade
In the Cisco ONS 15454, DS1 electrical cards can be upgraded to DS1/E1-56 high-density cards using TL1. This procedure can be performed only when logged in as a Superuser.
Note
•
•
–
–
•
Step 1
Input format:
CHG-EQPT:[<TID>]:<AID>:<CTAG>::<NEW_EQPT_TYPE>;
Input example:
CHG-EQPT::SLOT-15:123::DS1-E1-56;
Step 2
Step 3
Input format:
SW-TOPROTN-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<DIRN>];
Input example:
SW-TOPROTN-EQPT::SLOT-16:123::FRCD,SLOT-15,BTH;
Step 4
Input format:
CHG-EQPT:[<TID>]:<AID>:<CTAG>::<NEW_EQPT_TYPE>;
Input example:
CHG-EQPT::SLOT-16:123::DS1-E1-56;
Step 5
Step 6
Input format:
SW-TOWKG-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<DIRN>];
Input example:
SW-TOWKG-EQPT::SLOT-16:123::FRCD,BTH;
Step 7
2.10 Remote Monitoring-Managed PMs
This section describes the retrieval, threshold setting, threshold crossing alerts (TCAs) and scheduled PM reporting for all the remote monitoring (RMON)-managed PM data in the Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, and ONS 15600.
Note
The cards that support RMON PMs include: G1K-4, CE-1000-4, ML1000-2/ML100T-12, FC_MR-4, ASAP-4, MXP_MR_2.5G/MXPP_MR_2.5G, and ML-100T-8/CE-100T-8. The PM types for these cards include Ethernet statistic types defined in standard Simple Network Management Protocol (SNMP)/RMON MIBs, and also include other statistic types managed by RMON, for example, the Fibre Channel statistic types.
When creating an RMON threshold, there are two threshold values that need to be specified. The first threshold is the rising threshold and the other is the falling threshold. There are other parameters that need to be specified when creating the RMON threshold, for example, the startup type and the sample type.
Note
The current bucket is not defined by the RMON. RMON-managed PM only shows the history data of the PMs and the data accumulated since the last time the counters are cleared (RAW-DATA).
In the RMON TCA, the accumulation time period is not the predefined PM bucket accumulation time, such as 15-MIN or 1-DAY. It can be any integer (any time greater than 10 seconds) that is defined when creating the RMON threshold.
Note
2.10.1 RTRV-PM-<MOD2>
The RTRV-PM-<MOD2> command retrieves the RMON-managed PMs.
The TL1 modifiers FSTE/GIGE/POS are used to retrieve the RMON-managed Ethernet PMs if the Ethernet port is an FSTE/GIGE/POS port type. The FC modifier retrieves the RMON-managed Fibre Channel PMs.
There are three accumulation time periods for RMON statistics: 1-MIN, 1-HR, and RAW-DATA. For RMON-managed PMs, only history PM buckets and RAW-DATA are supported and there is no current bucket defined for RMON-managed PMs. When RAW-DATA is specified in the input of RTRV-PM, the date and time specified in the input will be ignored. The MONDATE and MONTIME in the output will be the last time the counters were cleared. RAW-DATA will be the default TMPER value for RMON-managed PM retrieval.
Because RMON PM only supports the history data if the accumulation time period is 1-MIN, 15-MIN, 1-HR, or 1-DAY, you must specify the correct history PM bucket for the RTRV-PM command to succeed.
When retrieving PM, if an unsupported MONYYPR is specified, an error message will be returned.
Currently there is no support of LOCN (location) and DIRN (direction) for RMON-managed data statistics.
Input FormatRTRV-PM-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<MONLEV>],[<lSTM>],
[<DIRECTION>],[<TMPER>],[<DATE>],[<TIME>];Input ExampleRTRV-PM-GIGE:TID:FAC-2-1:123::ETHERSTATSOCTETS,,,,1-MIN,04-11,12-45;
RTRV-PM-GIGE:TID:FAC-2-1:123::,,,,RAW-DATA;
Output FormatSID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<MONTYPE>,<MONVAL>,[<VLDTY>],[<LOCN>],
[<DIRECTION>],[<TMPER>],[<MONDAT>],[<MONTM>]"
;Output ExampleTID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-2-1,GIGE:etherStatsOctets,21,COMPL,,,1-MIN,04-11,12-45"
;Table 2-11 shows the error messages associated with the RTRV-PM-<MOD2> command.
2.10.2 ENT-RMONTH-<MOD2_RMON>
The ENT-RMONTH-<MOD2_RMON> command creates a threshold type (an entry in the RMON alarm table) for an RMON statistic, for the RMON-managed PMs. An event (TCA) is generated and reported when the threshold is crossed in the appropriate direction during the sampled time period.
More than one threshold can be created by using different parameters (rising/falling threshold), for each MONTYPE.
This command applies to G1000, GIGE, FSTE, POS, and FC data objects.
Input FormatENT-RMONTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,,,<INTVL>:RISE=<RISE>,
FALL=<FALL>,[SAMPLE=<SAMPLE>,][STARTUP=<STARTUP >][:];Input ExampleThe following example creates an entry in the RMON threshold table for the etherStatsOctets statistic type with an interval equal to 100 seconds, rising threshold of 1000, falling threshold of 100, DELTA sampling type, and startup type of RISING-OR-LTING.
ENT-RMONTH-GIGE:CISCO:FAC-2-1:123::ETHERSTATSOCTETS,,,,100:RISE=1000,
FALL=100,SAMPLE=DELTA,STARTUP=RISING-OR-LTING;Table 2-12 shows the error messages associated with the ENT-RMONTH-<MOD2_RMON> command.
2.10.3 DLT-RMONTH-<MOD2_RMON>
The DLT-RMONTH-<MOD2_RMON> command deletes a threshold type (an entry in the RMON alarm table) created for a MONTYPE (RMON statistic type). Because there can be multiple thresholds created for a particular MONTYPE, you must specify all the necessary parameters for the threshold in order to identify the particular threshold to be deleted.
This command applies to G1000, GIGE, FSTE, POS, and FC data objects.
Input FormatDLT-RMONTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,,,<INTVL>:RISE=<RISE>,
FALL=<FALL>,[SAMPLE=<SAMPLE>,][STARTUP=<STARTUP>][:];Input ExampleThe following example deletes an entry in the RMON threshold table for the etherStatsOctets statistic type, with an interval equal to 100 seconds, rising threshold of 1000, falling threshold of 100, DELTA sampling type, and startup type of BOTH.
DLT-RMONTH-GIGE:CISCO:FAC-2-1:123::ETHERSTATSOCTETS,,,,100:RISE=1000,FALL=100,
SAMPLE=DELTA,STARTUP=BOTH;Table 2-13 shows the error messages associated with the DLT-RMONTH-<MOD2_RMON> command.
2.10.4 RTRV-RMONTH-<MOD2_RMON>
The RTRV-RMONTH-<MOD2_RMON> command retrieves the thresholds defined in the RMON alarm table.
Input FormatRTRV-RMONTH-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>]>,,,,
[<INTVL>]:[RISE=<RISE>,][FALL=<FALL>,][SAMPLE=<SAMPLE>,][STARTUP=<STARTUP>];Input ExampleThe following example retrieves all the thresholds defined in the RMON threshold table for the etherStatsOctets statistics type.
RTRV-RMONTH-GIGE:TID:FAC-2-1:123::ETHERSTATSOCTETS;
The following example retrieves all the thresholds for the etherStatsOctets statistics type with the DELTA sampling type and RISING startup type defined in the RMON threshold table.
RTRV-RMONTH-GIGE:CISCO:FAC-2-1:123::ETHERSTATSOCTETS:SAMPLE=DELTA,
STARTUP=RISING;Output FormatSID DATE TIME
M CTAG COMPLD
"<AID>,[<AIDTYPE>]:<MONTYPE>,,,,[<INTVL>]:INDEX=<INDEX>,RISE=<RISE>,
FALL=<FALL>,SAMPLE=<SAMPLE>,STARTUP=<STARTUP>"
;Output ExampleTID-000 1998-06-20 14:30:00
M 001 COMPLD
"FAC-2-1,GIGE:ETHERSTATSOCTETS,,,,100:INDEX=2,RISE=1000,FALL=100,
SAMPLE=DELTA,STARTUP=RISING"
;Table 2-14 shows the error messages associated with the DLT-RMONTH-<MOD2_RMON> command.
2.10.5 REPT EVT <MOD2ALM> for Threshold Crossing Events
The REPT EVT <MOD2ALM> autonomous message reports the threshold crossing event for the RMON statistics. The high threshold (HT) designator is generated when crossing the RISING threshold. The low threshold (LT) is generated when crossing the FALLING threshold.
The table index for thresholds in the RMON alarm table is enclosed in the text of the TCA description. This table index also appears in the output of the RTRV-RMONTH command. You can retrieve additional information regarding the threshold that generates the TCA by issuing the RTRV-RMONTH command and comparing the output with corresponding table index.
Output FormatSID DATE TIME
M CTAG COMPLD
"<AID>:<CONDTYPE>,[<CONDEFF>],[<OCRDAT>],[<OCRTM>],[<LOCN>],,[<MONVAL>],
[<THLEV>],[<TMPER>]:[<DESC>],[<AIDDET>]"
;Output ExampleVA454-23 2000-02-20 08:47:03
A 512.512 REPT EVT G1000
"FAC-2-1,G1000:T-ETHERSTATSOCTETS-HT,TC,09-30,23-59-59,,,1003,
1000,:\"RMON THRESHOLD CROSSING ALARM # 1 \",G1000-4"
;2.10.6 INIT-REG-<MOD2>
This command initializes the PM registers.
This command applies to G1K-4, GIGE, FSTE, and FC data objects.
Only RAW-DATA is allowed to be specified for TMPER because no history data will be cleared for RMON-managed PMs by INIT-REG-<MOD2>.
2.10.7 SCHED-PMREPT-<MOD2>
This command schedules/reschedules the NE to report the performance monitoring data.
The three accumulation time periods form RMON statistics are: 1-MIN, 1-HR, and RAW-DATA.
2.10.8 RTRV-PMSCHED-<MOD2>
This command retrieves the RMON statistics reporting schedule that was set for the NE by the SCHED-PMREPT-<MOD2> command.
The LOCN parameter is optional in the output of RTRV-PMSCHED-<MOD2>, and no LOCN information will be given in the output of RTRV-PMSCHED for RMON PM schedule.
2.10.9 REPT PM <MOD2>
Reports autonomous monitoring statistics as a result of the schedule created by SCHED-PMREPT-<MOD2>.
The LOCN parameter is optional in the output of REPT PM <MOD2> message, and no LOCN information will be given in the output of REPT PM <MOD2>.
2.10.10 REPT DBCHG
Reports any changes on the NE that result from issuing the following commands:
•
•
Also reports when an RMON PM schedule is created or deleted through the SCHED-PMREPT-<MO2> command.
2.10.11 MONTYPE and CONDEF Defined for TCA
The names of Ethernet and Fibre Channel MONTYPEs are defined exactly as they are defined in the corresponding SNMP MIB statistics group. For example, etherStatsUndersizePkts will be used as the name for the same RMON statistics defined in request for comment (RFC)1757.
Unlike the PM parameters of other SONET entities (such as STS path and OCn), there are two CONDEFs defined for the TCAs of each RMON-managed statistics type: Ethernet or Fibre Channel MONTYPE. One CONDEF is for the rising threshold, and the other is for the falling threshold. For example, there are two CONDEFs for the etherStatsUndersizePkts statistics type: T-etherStatsUndersizePkts-HT for the rising threshold, and T-etherStatsUndersizePkts-LT for the falling threshold.
Note
2.10.12 Enumerated Types
2.10.12.1 TMPER
Table 2-15 shows the possible TMPER values.
2.10.12.2 SAMPLE_TYPE
SAMPLE_TYPE ( Table 2-16) describes how the data will be calculated during the sampling period.
Table 2-16 SAMPLE_TYPE
ABSOLUTE
Comparing directly.
DELTA
Comparing with the current value of the selected variable subtracted by the last sample.
2.10.12.3 STARTUP_TYPE
STARTUP_TYPE ( Table 2-17) indicates whether an event will be generated when the first valid sample is crossing the rising or falling threshold.
2.10.13 Notes for DWDM Card Types
The PM for client port and/or optical channel (OCH) can include both the RMON-managed PM and the SONET PM when the client payload is provisioned as 1GFC, 2GFC, 10GFC, 1GFICON, 2GFICON, GIGE, or 10GIGE for the following cards:
•
•
•
•
•
2.10.13.1 Client Port of DWDM Cards
When the client port of a dense wavelength division multiplexing (DWDM) card is provisioned as 1GFC, 2GFC, 10GFC, 1GFICON, 2GFICON, GIGE, or 10GIGE, the applicable PM for the client port includes both the RMON-managed PM and the SONET PM. Therefore, the behavior of the RTRV-PM-<MOD2>, INIT-REG-<MOD2>, and SCHED-PMREPT-<MOD2> commands is different from the Ethernet or Fibre Channel port of the other cards where only RMON PM is applicable. The differences include:
•
•
•
•
•
ENT-RMONTH-GIGE::FAC-2-1-1:1::IFINOTETS,,,,1000:RISE=1000,FALL=900;
In the same client port, the following command would be used to set the SONET the optics PM threshold:
SET-TH-GIGE::FAC-2-1-1:1LBCL-MIN,0.2;
2.10.13.2 OCH Port of DWDM Cards
The optical channel (OCH) port of the TXP_MR_10G and TXP_MR_10E cards include the RMON-managed 8B10B PM as well as the other SONET PMs, when their client port is provisioned as GIGE, 10GIGE, 1GFC, 2GFC, or 10GFC.
The RTRV-PM-OCH, INIT-REG-OCH, SCHED-PMREPT-OCH, and REPT PM OCH commands have behaviors similar to those mentioned in the "Client Port of DWDM Cards" section.
2.11 Rules for Framing Type Autoprovisioning in CTC Versus TL1
The DS3, DS3E, DS3XM, DS3i, and DS1 cards can autosense framing and set the format accordingly; however, this framing autosense feature can only be set using CTC. Use CTC to set the frame format (FMT) attribute on DS3, DS3E, DS3XM, DS3i, and DS1 cards to autoprovision. The FMT field will blank out for a few seconds while the card is determining the framing mode received by that particular port. The FMT field is set accordingly to unframed, M23, or CBit. If the card is not present (preprovisioned), setting the FMT field to autoprovision will result in the FMT field defaulting to unframed.
The TL1 interface does not support the autoprovision option for the DS3, DS3E, DS3XM, DS3i, and DS1 cards; it only supports unframed, M23, or CBit. If autoprovision is selected from CTC and at the same time the TL1 command RTRV-T3 is issued, the TL1 output will indicate the FMT field as unframed during the time period that the card (if present) is autosensing the frame format. If the card is not present (preprovisioned), the response of the RTRV-T3 command (after CTC sets the FMT to autoprovision) will indicate the FMT field as unframed.
2.12 Provisioning Rules for Transponder and Muxponder Cards
This section provides provisioning rules associated with the following cards and their pluggable port modules (PPMs):
•
•
•
•
•
•
•
•
2.12.1 PPM Provisioning Rules
PPMs must be provisioned. Use the ENT-EQPT command to provision PPMs. For example, to provision the first PPM on Slot 2, use the following command:
ENT-EQPT::PPM-2-1:100::PPM-1PORT;
To delete PPM provisioning, use the DLT-EQPT command.
2.12.2 Payload Provisioning Rules
Use the following rules when provisioning payload:
•
•
–
–
–
–
–
–
–
•
•
The TL1 commands for provisioning payload are:
•
•
•
2.12.3 OC-N Payload Provisioning Parameters
SONET payloads are supported by DWDM cards according to Table 2-18. These payloads are configurable only for the Section and Line layers. STS layers cannot be provisioned or retrieved.
Table 2-18 Payload/Card Mode Support
TXP_MR_10G
OC192
DWDM-LINE
10GIGE
DWDM-SECTION
DWDM-TRANS-AIS
With REGEN group: DWDM-TRANS-AISMXP_2.5G_10G
OC48
DWDM-LINE
DWDM-SECTION
DWDM-TRANS-AISTXP_MR_2.5G and TXPP_MR_2.5G
1GIGE, 1GF, 1GFICON, 2GFICON, ESCON, ISC1, ISC3, ETRCLO, DV6000, HDTV, D1VIDEO
With REGEN group: DWDM-TRANS-AIS
Must be DWDM-TRANS-AIS. Requires the DWRAP and FEC disabled on the network/OCH ports.OC3, OC12, OC48
DWDM-LINE
DWDM-SECTION
DWDM-TRANS-AISTXP_MR_10E
OC192
DWDM-LINE
DWDM-SECTION
DWDM-TRANS-AIS DWDM-TRANS-SSQUELCH10GIGE, 10GFC
DWDM-TRANS-AIS DWDM-TRANS-SQUELCH
With REGEN group:
DWDM-TRANS-AIS DWDM-TRANS-SQUELCHMXP_2.5G_10E
OC48
DWDM-SECTION
DWDM-TRANS-AIS DWDM-TRANS-SQUELCHMXP_MR_2.5G and MXPP_MR_2.5G
Port-1: 1GFC, 1GFICON, GIGE
Port-2: 1GFC, 2GFC, 1GFICON, 2GFICON, GIGE1
FCGE2
1 If 2GFC or 2GFICON is on Port-2, then Port-1 must be unprovisioned. If Port-1 is provisioned, then Port-2 cannot contain 2GFC or 2GFICON because of bandwidth limitations. Ports 3 through 8 are not available. ESCON payload is not supported.
2 ESCON and mixed card modes are not supported.
The configuration parameters for OCn ports can be retrieved/edited using the ED-<OCN_TYPE> and RTRV-<OCN_TYPE> commands. The following is a list of restrictions when using the ED-<OCN_TYPE> and RTRV-<OCN_TYPE> commands:
•
•
•
•
•
•
•
•
•
2.12.4 Termination Mode Provisioning Rules
Use the following rules when provisioning the termination mode:
•
•
•
–
–
–
–
–
•
•
•
To set the termination mode, use the following commands:
•
•
Example 2-32 sets the termination mode of the card in Slot 1 to DWDM-LINE.
Example 2-32 Set the Termination Mode
ED-EQPT::SLOT-1:116:::CARDMODE=DWDM-LINE;2.12.5 Wavelength Provisioning Rules
Use the following rules when provisioning the wavelength:
•
•
•
•
Use the ENT-EQPT and ED-EQPT commands to set the card-level wavelength. The following example sets the wavelength of the card in Slot 1 to 1530.33:
ED-EQPT:VA454-22:SLOT-1:116:::PWL=1530.33;
2.12.6 Regeneration Group Provisioning Rules
Use the following rules when provisioning the regeneration group:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Use the ED-EQPT and ENT-EQPT commands to set a card-level regeneration group. The following command sets a card-level regeneration group for Slot 2.
ED-EQPT::SLOT-2:CTAG:::PROTID=SLOT-2,NAME=REGENGROUPNAME;
2.12.7 DCC/GCC Provisioning Rules
Use the following rules when provisioning DCC and GCC:
•
•
•
•
•
–
–
•
•
Use the ED-(OCn, nGIGE, NGFC) command to provision DCC, as shown in the following command:
ED-OC192::FAC-1-1-1:100:::COMM=DCC:OOS,AINS;
Use the ED-OCH command to provision GCC, as shown in the following command:
ED-OCH::CHAN-6-2:114::COMM=GCC:OOS,AINS;
2.12.8 ITU-T G.709 OTN, FEC, and OTN SDBER/SFBER Provisioning Rules
Use the following rules when provisioning ITU-T G.709 OTN, FEC, and OTN SDBER/SFBER:
•
•
•
–
–
•
–
–
•
•
•
•
•
Use the ED-OCH commands to provision ITU-T G.709, FEC, and OTN SDBER/SFBER, as shown in the following example:
ED-OCH::CHAN-6-2:114:::OSDBER=1E-6,DWRAP=Y,FEC=Y,:OOS,AINS;
2.12.9 Synchronization Provisioning Rules
Use the following rules when provisioning synchronization:
•
•
•
•
•
Use the ENT-OCn, ED-OCn, and ED-OCH commands to set port-level synchronization attributes, as shown in the following examples:
ED-OC48::FAC-1-1-1:CTAG:::SYNCMSG=Y,SENDDUS=N:;
ED-OCH::CHAN-6-2:114:::SYNCMSG=N,SENDDUS=Y;:
2.12.10 Section Trace Provisioning (J0) Rules
Use the following rules when provisioning section trace (J0):
•
•
•
•
•
•
•
•
•
•
•
•
•
Use the ED-OCn command for trace provisioning of client ports provisioned for OCn payload, as shown in the following example:
ED-OC48::FAC-6-1-1:10:::EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,
TRCFORMAT=16-BYTE;Use the ED-TRC-OCH command for trace provisioning of trunk/OCH DWDM ports, as shown in the following example:
ED-TRC-OCH::CHAN-6-2:10:::EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,
TRCLEVEL-J0,TRCFORMAT=64-BYTE;2.12.11 Trail Trace Identification Provisioning Rules
Use the following rules when provisioning trail trace identification (TTI):
•
•
•
•
•
•
Use the ED-TRC-OCH command to provision port-level trace, as shown in the following example:
ED-TRC-OCH::CHAN-6-2:10:::EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,
TRCLEVEL=TTI-PM,TRCFORMAT=64-BYTE;2.12.12 PM and Alarm Threshold Provisioning Rules
Use the following rules when provisioning PM parameters and alarm thresholds:
•
•
•
–
–
•
•
•
•
•
•
•
•
Use the SET-TH-(OCn, nGIGE, nGFC, OCH) command to set port-level thresholds, for example:
SET-TH-OC48::FAC-1-1-1:123::CVL,12,NEND,,15-MIN;
SET-TH-OCH::CHAN-6-1:123::ES-PM,12,NEND,,15-MIN;
Use the RTRV-PM-(OCn, nGIGE, nGFC, OCH) command to retrieve port-level thresholds, for example:
RTRV-PM-OC48::FAC-1-1-1:123::CVL,10-UP,NEND,BTH,15-MIN,04-11,12-45;
RTRV-PM-OCH::CHAN-6-1:123::ES-PM,10-UP,NEND, BTH,15-MIN,04-11,12-45:
2.12.13 Y-Cable Protection Group Provisioning Rules
Use the following rules when provisioning a Y-cable protection group:
•
•
•
•
•
Use the ENT-FFP-(OCn, nGIGE, nGFC), DLT-FFP-(OCn, nGIGE, nGFC), and ED-FFP-(OCn, nGIGE, nGFC) commands to provision Y-cable protection groups, as shown in the following examples:
ENT-FFP-OC48::FAC-1-1-1,FAC-2-1-1:100:::PROTTYPE=Y-CABLE,
PROTID=DC-METRO-1,RVRTV=Y,RVTM=1.0,PSDIRN=BI:ENT-FFP-10GIGE::FAC-1-1-1,FAC-2-1-1:100:::PROTTYPE=Y-CABLE,
PROTID=DC-METRO-2,RVRTV=Y,RVTM-1.0,PSDIRN=BI;2.12.14 Splitter Protection Group Provisioning Rules
Use the following rules when provisioning a splitter protection group:
Note
•
•
•
The TL1 command to a provision splitter protection group ( Example 2-33) is:
•
Example 2-33 Provisioning Splitter Protection Group Attributes:
ED-FFP-OCH::CHAN-2-1:100:::PROTID=DC-METRO3,RVRTV=Y, RVTM=5.0,PSDIRN=BI;2.12.15 Loopback Provisioning Rules
Use the following rules when provisioning loopbacks:
•
•
•
•
–
–
–
–
–
–
The TL1 command is OPR-LPBK-OCH.
Example of operating a loopback:
OPR-LPBK-OCH::CHAN-2-1:1::,,,TERMINAL;
2.12.16 Automatic Laser Shutdown Provisioning Rules
Use the following rules when provisioning automatic laser shutdown (ALS):
•
•
•
Use the ED-ALS and ED-ALS-(OCn, nGIGE, nGFC, OTS, OMS, OCH) commands to provision ALS, as shown in the following examples:
ED-ALS::FAC-1-1-1:100:::ALSMODE=Y,ALSRCINT=130,ALSRCPW=35.1,RLASER=Y;
ED-ALS-OC192::FAC-1-1-1:100:::ALSMODE=Y,ALSRCINT=130,ALSRCPW=35.1,
RLASER=Y;2.12.17 Port State Model Provisioning Rules
Use the following rules when provisioning the port state model:
•
•
•
–
–
–
Use the ED-(OCn, nGIGE, nGFC, OCH) command to edit the port state, as shown in the following examples:
ED-OC48::FAC-6-1-1:114::::OOS,AINS;
ED-10GIGE::FAC-6-1:114::::OOS,AINS;
ED-OCH::CHAN-6-1:114::::IS;
2.12.18 SONET-Related Provisioning Rules
When provisioning SONET-related parameters, the SDBER and SFBER can only be provisioned on the working trunk port (OCH) for the protect TXP card. Values set at the working port will be reflected on the trunk port.
Use the ED-OCH command to edit SONET trunk port attributes, as shown in the following example:
ED-OCH::CHAN-6-2:114:::RDIRN=W-E,EXPWLEN=1530.32,VOAATTN=2.5,VOAPWR=7.5,
CALOPWR=0,CHPOWER=2.0,NAME="NYLINE",SFBER=1E-5,SDBER=1E-6,
ALSMODE=MAN,ALSRCINT=60,ALSRCPW=35.1,COMM=DCC,GCCRATE=192K,
OSDBER=1E-6,DWRAP=Y,FEC=Y,MACADDR=OO-OE-AA-BB-CC-DD,SYNCMSG=N,
SENDDUS=Y,RLASER=Y,SOAK=10,OSPF=Y:OOS,AINS;2.12.19 Overhead Circuit Provisioning Rules
1.
2.
a.
b.
c.
3.
4.
5.
6.
2.12.20 Hardware Limitation Rules
The DWDM cards have the following hardware limitations:
•
•
•
Posted: Wed Jul 11 08:30:43 PDT 2007
All contents are Copyright © 1992--2007 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
