|
|
Table Of Contents
11.19 ED-FFP-<MOD2DWDMPAYLOAD>
ED Commands
Note
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This chapter provides edit (ED) commands for the Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, and ONS 15600.
11.1 ED-<GIGE_TYPE>
(Cisco ONS 15454, ONS 15600) The Edit 10GIGE or GIGE (ED-<GIGE_TYPE>) command edits Ethernet facility attributes.
Usage Guidelines
•
•
•
•
CategoryPorts
SecurityProvisioning
Input FormatED-<GIGE_TYPE>:[<TID>]:<AID>:<CTAG>:::[ADMINSTATE=<ADMINSTATE>],
[LINKSTATE=<LINKSTATE>],[MTU=<MTU>],[FLOWCTRL=<FLOWCTRL>],
[AUTONEG=<AUTONEG>],[HIWMRK=<HIWMRK>],[LOWMRK=<LOWMRK>],
[OPTICS=<OPTICS>],[DUPLEX=<DUPLEX>],[SPEED=<SPEED>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[MACADDR=<MACADDR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[SOAK=<SOAK>]:[<PST>[,<SST>]];Input ExampleED-GIGE:CISCO:FAC-1-1:123:::ADMINSTATE=DOWN,LINKSTATE=DOWN,MTU=1548,
FLOWCTRL=NONE,AUTONEG=Y,HIWMRK=485,LOWMRK=25,OPTICS=1000_BASE_LX,
DUPLEX=AUTO,SPEED=AUTO,NAME="GIGE PORT",CMDMDE=FRCD,
MACADDR=00-0E-AA-BB-CC-FF,FREQ=1550,LOSSB=SX,SOAK=32:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<ADMINSTATE>
The parameter type is UP_DOWN which indicates an up or down value
•
Down
•
Up
<LINKSTATE>
The parameter type is UP_DOWN which indicates an up or down value
•
Down
•
Up
<MTU>
Maximum transport unit. The parameter type is MTU_TYPE which indicates the maximum transport unit used by an Ethernet card. Defaults to 9600.
•
10004. Indicates jumbo size.
•
1500
•
1548
•
9600. Indicates the jumbo size.
<FLOWCTRL>
Flow control. The parameter is FLOW which indicates the type of flow control that has been negotiated for an Ethernet port. Defaults to NONE.
•
Asymmetric flow control
•
Asymmetric local flow control
•
No flow control
•
Passthrough flow control
•
Symmetric flow control
<AUTONEG>
Autonegotiation. The parameter is ON_OFF which disables or enables an attribute. Defaults to Y.
•
Disable an attribute
•
Enable an attribute
<HIWMRK>
High water mark. Integer. Defaults to 485.
<LOWMRK>
Low water mark. Integer. Defaults to 25.
<OPTICS>
The parameter is OPTICS which indicates the type of Gigabyte Ethernet optics being used.
•
1000 Base CX
•
1000 Base LX
•
1000 Base SX
•
1000 Base ZX
•
100 Base FX
•
100 Base LX
•
Coarse wavelength division multiplexing (CWDM) 1470
•
CWDM 1490
•
CWDM 1510
•
CWDM 1530
•
CWDM 1550
•
CWDM 1570
•
CWDM 1590
•
CWDM 1610
•
ITU-100G 1530.33
•
ITU-100G 1531.12
•
ITU-100G 1531.90
•
ITU-100G 1532.68
•
ITU-100G 1534.25
•
ITU-100G 1535.04
•
ITU-100G 1535.82
•
ITU-100G 1536.61
•
ITU-100G 1538.19
•
ITU-100G 1538.98
•
ITU-100G 1539.77
•
ITU-100G 1540.56
•
ITU-100G 1542.14
•
ITU-100G 1542.94
•
ITU-100G 1543.73
•
ITU-100G 1544.53
•
ITU-100G 1546.12
•
ITU-100G 1546.92
•
ITU-100G 1547.72
•
ITU-100G 1548.51
•
ITU-100G 1550.12
•
ITU-100G 1550.92
•
ITU-100G 1551.72
•
ITU-100G 1552.52
•
ITU-100G 1554.13
•
ITU-100G 1554.94
•
ITU-100G 1555.75
•
ITU-100G 156.55
•
ITU-100G 1558.17
•
ITU-100G 1558.98
•
ITU-100G 1559.79
•
ITU-100G 1560.61
•
Unknown
•
Unplugged
<DUPLEX>
The parameter is ETHER_DUPLEX which indicates duplex mode. Defaults to AUTO.
•
Auto mode
•
Full mode
•
Half mode
<SPEED>
The parameter type is ETHER_SPEED which indicates Ethernet speed. Defaults to AUTO.
•
100 Mbps
•
10 Gbps
•
10 Mbps
•
1 Gbps
•
Automatic
<NAME>
Port name. NAME is a string. Defaults to NULL. Maximum length is 32 characters.
<CMDMDE>
Command execution mode. NORM for normal (default) and FRCD for forced. FRCD will override any safeguards that normally reject a request to delete an in service resource.
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<MACADDR>
MACADDR is a string. Defaults to NULL. Maximum length is 18 characters.
<FREQ>
The parameter type is OPTICAL_WLEN which indicates the optical wavelength.
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
The parameter type is REACH which indicates the reach values.
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
<SOAK>
IS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer. Defaults to 32.
<PST>
The primary state. The parameter type is PST, which indicates the current overall service condition of an entity. Defaults to OOS.
•
In service
•
Out of service
SST
The secondary state. The parameter type is SST, which provides additional information pertaining to PST and primary state qualifier (PSTQ). Defaults to DSBLD.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.2 ED-<MOD1FCPAYLOAD>
(Cisco ONS 15454) The Edit 1GFC, 2GFC, or 4GFC (ED-<MODFCPAYLOAD>) command edits the attributes related to the Fibre Channel (FC) facility. The state IS,AINS is not supported on the FC port.
Usage Guidelines
See Table 27-1 for supported modifiers by platform.
Note
•
•
CategoryPorts
SecurityProvisioning
Input FormatED-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],
[DISTEXTN=<DISTEXTN>],[AUTODETECTION=<AUTODETECTION>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>],
[LOSSB=<LOSSB>]:[<PST>[,[<SST>]];Input ExampleED-1GFC:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,MFS=2148,NAME="FC PORT",CMDMDE=CMDMDE,SOAK=32,
FREQ=1550,LOSSB=LR-1:OOS,MT;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<LINKRCVRY>
Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<DISTEXTN>
Distance extension. It can be set to Buffer-to-Buffer (B2B) Credit Management state or None.
Note
The parameter type is DISTANCE_EXTENSION (distance extension).
•
Buffer to buffer flow control
•
No distance extension
<AUTODETECTION>
Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute
•
Enable an attribute
<LINKCREDITS>
Number of link credits. If autodetection is set to off, the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.
<MFS>
Maximum frame size. MFS is an integer.
<NAME>
String
<CMDMDE>
Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG.
Parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<SOAK>
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<FREQ>
The parameter type is OPTICAL_WLEN, which is the optical wavelength.
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
the parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
<PST>
Primary state. the parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.3 ED-<MOD1FICONPAYLOAD>
(Cisco ONS 15454) The Edit 1GFICON, 2GFICON, or 4GFICON (ED-<MOD1FICONPAYLOAD>) command edits the attributes related with the fiber connectivity (FICON) payload facility. The state IS,AINS is not supported on the FICON port.
Usage Guidelines
See Table 27-1 for supported modifiers by platform.
CategoryPorts
SecurityProvisioning
Input FormatED-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],
[DISTEXTN=<DISTEXTN>],[AUTODETECTION=<AUTODETECTION>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>],
[LOSSB=<LOSSB>]:[<PST>[,<SST>]];Input ExampleED-1GFICON:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,MFS=2148,NAME="FC PORT",CMDMDE=CMDMDE,SOAK=32,FREQ=1550,
LOSSB=LR-1:OOS,MT;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<LINKRCVRY>
Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute
•
Enable an attribute
<DISTEXTN>
Distance extension. It can be set to B2B Credit Management state or None.
Note
The parameter type is DISTANCE_EXTENSION (distance extension).
•
Buffer to buffer flow control
•
No distance extension
<AUTODETECTION>
Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute
•
Enable an attribute
<LINKCREDITS>
Number of link credits. If autodetection is set to off the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.
<MFS>
Maximum frame size. MFS is an integer.
<NAME>
String
<CMDMDE>
Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG.
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<SOAK>
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<FREQ>
The parameter type is OPTICAL_WLEN (optical wavelength).
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
The parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.4 ED-<MOD2DWDMPAYLOAD>
(Cisco ONS 15454) The Edit 10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, ETRCLO, GIGE, HDTV, ISC1, ISC3, or PASSTHRU (ED-<MOD2DWDMPAYLOAD>) command edits the operating parameters for a dense wavelength division multiplexing (DWDM) client facility.
Usage Guidelines
See Table 27-1 for supported modifiers by platform.
CategoryDWDM
SecurityProvisioning
Input FormatED-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:[<PST>[,<SST>]];Input ExampleED-HDTV::FAC-1-1:1:::NAME="PORTNAME",CMDMDE=CMDMDE,FREQ=1550,
LOSSB=LR-1:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<LINKCREDITS>
Number of link credits. If autodetection is set to off the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.
<NAME>
String
<CMDMDE>
Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG.
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<FREQ>
The parameter type is OPTICAL_WLEN (optical wavelength).
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
the parameter type is REACH, which is the reach value.
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.5 ED-<MOD_PATH>
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, VC12, VC3, VT1, or VT2 (ED-<MOD_PATH>) command edits the attributes associated with synchronous transport signal (STS) and Virtual Tributary (VT) paths.
Usage Guidelines
The SFBER, SDBER, RVRTV, and RVTM parameters only apply to unidirectional path switched rings (path protection configurations) at the STS path level and ONS 15310_CL and ONS 15454 VT paths.
SFBER and SDBER also apply to the VT path level on the ONS 15310-CL and ONS 15454 when the ONS 15454 has an XC-VXC-10G card.
SWPDIP does not apply to the VT path level (VT1 and VT2).
The path trace message is a 64 character string including the terminating CR (carriage return) and LF (line feed) that is transported in the J1 byte of the SONET STS Path overhead. Both the EXPTRC and TRC string can be provisioned by user with up to 62 character string.
The EXPTRC indicates that the contents of the expected incoming path trace are provisioned by the user. The TRC indicates the contents of the outgoing path trace message. The INCTRC indicates the contents of the incoming path trace message.
Path trace has three modes: OFF, MANUAL, and AUTO. The path trace mode defaults to OFF. The MANUAL mode performs the comparison of the received string with the user-entered expected string. The AUTO mode performs the comparison of the present received string with an expected string that is set to a previously received string. If there is a mismatch, a TIM-P alarm is raised. When the path trace is in OFF mode, there is no path trace processing, and all of the alarm and state conditions are reset.
The TACC parameter edits an existing single STS or VT and changes it to a test access point. When an editing command on TACC is executed, it assigns the STS or VT for the first two-way connection and STS+1 as the second two-way connection. For single facility access digroup (FAD) test access, only a single STS/VT is used for the test access point (TAP) creation. For more information on TACC, refer to the Cisco ONS SONET TL1 Reference Guide.
J1 is implemented on the DS1/DS1N, DS3E/DS3NE, DS3XM, EC1, OC3, OC12-4, OC48AS, and OC192 cards.
DS3/DS3N, OC12, OC48, E100, and E1000 cards do not support path trace.
DS1/DS1N, DS3E/DS3NE, and DS3XM support both TRC and EXPTRC in the ED-STS-PATH command.
EC1, OC3, OC48AS, and OC192 only support EXPTRC in the ED-STS-PATH command.
Note
The following actions will produce error messages:
•
•
•
•
•
Note
•
•
•
•
•
•
–
–
–
•
•
•
•
For TACC creation, use the ED-STS3C command because the TACC path width (like the cross-connect) has to be 3C on the DS3i-N-12 card. In this case, you are creating a new entity (TAP) on the DS3i-N-12 card that has to be of 3C width. On the DS3i-N-12 card, the ED0STS command can be used either with STS1 or STS3C depending on the parameter to be modified.
•
•
•
•
•
•
CategoryPaths
SecurityProvisioning
Input FormatED-<MOD_PATH>:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>],[SDBER=<SDBER>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SWPDIP=<SWPDIP>],
[HOLDOFFTIMER=<HOLDOFFTIMER>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],
[TRCMODE=<TRCMODE>],[TRCFORMAT=<TRCFORMAT>][TACC=<TACC>],
[TAPTYPE=<TAPTYPE>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-STS3C:FERNDALE:STS-2-1-4:115:::SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,
SWPDIP=Y,HOLDOFFTIMER=2000,EXPTRC="EXPTRCSTRING",TRC="TRCSTRING",
TRCMODE=OFF,TRCFORMAT=64-BYTE,TACC=8,TAPTYPE=SINGLE,
CMDMDE=CMDMDE:IS,AINS;Input Parameters
<AID>
Access identifier from the "CrossConnectId1" section.
<SFBER>
Signal failure threshold. Applies only to path protection. Applies to STS-level paths in SONET (STSn) and to VT-level paths on the ONS 15310-CL with an XC-VXC-10G card. Defaults to 1E-4.
The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
Signal degrade threshold. Applies only to path protection. Applies to STS-level paths in SONET (STSn) and to VT-level paths on the ONS 15310-CL with an XC-VXC-10G card. 1E-9 is not allowed for VT-level/LO paths. Defaults to 1E-6.
The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<RVRTV>
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. Only applies to path protection.
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<RVTM>
Revertive time. RVTM is not allowed to be set while RVRTV is N. Only applies to path protection.
The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
<SWPDIP>
On/off switch for path protection payload defect level switching. Applicable only to STS-level paths in SONET (STSn). For the selector path on a BLSR, SWPDIP is not editable and always ON. Defaults to N.
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<HOLDOFFTIMER>
Hold off timer for path protection dual-ring interconnect (DRI). Values must be within 0 and 10000 ms (0 to 10 seconds), with increments of 100 ms. Defaults to "existed value." HOLDOFFTIMER is an integer.
<EXPTRC>
Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 and CE-100T-8 card on the ONS 15454 and the CE-100T-8 card on ONS 15310-CL. Defaults to 64 null characters. EXPTRC is a string.
<TRC>
The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the network element (NE) transmitting 62 null characters (hex 00) and CR and LF. Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 and CE-100T-8 card on the ONS 15454 and the CE-100T-8 card on ONS 15310-CL. For ONS 15310-CL, TRC is not provisionable on the EC/OC ports. Defaults to 64 null characters. TRC is a string.
<TRCMODE>
Path trace mode. Applicable only to STS-level paths in SONET (STSn). Defaults to the OFF mode. ONS 15310-CL EC/OC ports do not support MAN and AUTO, but can be configured as MAN-NO-AIS and AUTO-NO-AIS.
Note
The parameter type is TRCMODE (trace mode).
•
Use the previously received path trace string as the expected string. Not applicable to muxponder (MXP) and transponder (TXP) cards.
•
Use the previously received path trace string as the expected string and do not turn on the alarm indication signal (AIS) and remote defect indication (RDI) if TIM-P is detected.
•
Use the provisioned expected string as the expected string.
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.
•
Turn off path trace capability. Nothing will be reported.
<TRCFORMAT>
Path trace format. Only 64-byte is supported. Defaults to 64-byte. The parameter type is TRCFORMAT (trace format).
•
64 byte trace message
<TACC>
TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. TACC is an integer.
<TAPTYPE>
TAP type. Defaults to DUA The parameter type is TAPTYPE, which is the test access point type.
•
Dual FAD
•
Single FAD
<CMDMDE>
Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied. Defaults to NORM.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.6 ED-<MOD_RING>
(Cisco ONS 15454, ONS 15327, ONS 15600) The Edit Bidirectional Line Switched Ring (ED-<MOD_RING>) command edits the BLSR attributes.
Usage Guidelines
ONS 15327 and ONS 15600 do not support four-fiber BLSR.
The RVRTV, RVTM, SRVRTV, SRVTM, NODEID, and RINGID attributes can be edited for the four-fiber BLSR.
The RVRTV, RVTM, NODEID, and RINGID attributes can be edited for the two-fiber BLSR.
The following actions will produce errors:
•
•
•
•
•
•
•
•
•
•
Note
•
CategoryBLSR
SecurityProvisioning
Input FormatED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>][:];Input ExampleED-BLSR:PETALUMA:BLSR-43:123:::RINGID=43,NODEID=3,RVRTV=Y,RVTM=2.0,
SRVRTV=Y,SRVTM=5.0;Input Parameters
<AID>
Access identifier from the "AidUnionId1" section. Identifies the BLSR of the NE. The ALL and BLSR-ALL AIDs are not allowed for editing BLSRs.
<RINGID>
The BLSR ID of the NE up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.
<NODEID>
The BLSR node ID of the NE. NODEID ranges from 0 to 31. It is an integer.
<RVRTV>
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N.
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<RVTM>
Revertive time. RVTM is not allowed to be set while RVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
<SRVRTV>
The span revertive mode for four-fiber BLSR only. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<SRVTM>
The span revertive time for four-fiber BLSR only. SRVTM is not allowed to be set while SRVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
11.7 ED-<OCN_TYPE>
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit OC3, OC12, OC48, or OC192 (ED-OCN_TYPE>) command edits the attributes (for example, service parameters) and status of an OC-N facility. Allowable states for a facility are Out Of Service (OOS), Out Of Service and Automatic In Service (OOS-AINS), Out Of Service and Maintenance (OOS-MT), and In Service (IS).
Usage Guidelines
The LDCC parameter does not apply to ONS 15327.
The OPRNOMINAL parameter is supported only by optical card types that support Optical PM. The following cards support OPRNOMINAL: OC3-8, MRC-12, MRC-12-2.5G, MRC-4-2.5G, OC192-XFP, CTX-2500, CTX, OC192-4, OC48-16, OC192-4-DWDM, ASAP-4.
See Table 27-1 for supported modifiers by platform
The data communications channel (DCC) transmit side is bridged to both working and protect in a 1+1 protection scheme. On the receive side, the active one is selected for DCC. The DCC is provisioned on the working port only in a 1+1 protection scheme.
All lines in a 1+1 BLSR must have the same mode. If you change the mode of a line that is in a 1+1 BLSR, an error message will be returned.
The following apply to UNI-C DCC provisioning:
•
•
•
•
•
•
•
•
•
CategoryPorts
SecurityProvisioning
Input FormatED-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>],[AREA=<AREA>],
[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[PJMON=<PJMON>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],[MUX=<MUX>],
[SOAK=<SOAK>],[OSPF=<OSPF>],[LDCC=<LDCC>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],[TRCMODE=<TRCMODE>],
[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>],[SENDDUSFF=<SENDDUSFF>],
[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[FOREIGNFEND=<FOREIGNFEND>],[FOREIGNIP=<FOREIGNIP>],
[OPRNOMINAL=<OPRNOMINAL>]:[<PST>[,<SST>]];Input ExampleED-OC48:PENNGROVE:FAC-6-1:114:::DCC=Y,AREA=10.92.63.1,SYNCMSG=N,
SENDDUS=N,PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SINGLESHELF,
MUX=E2,SOAK=10,OSPF=Y,LDCC=N,NAME="OCNPORT",CMDMDE=CMDMDE,
EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,TRCFORMAT=16-BYTE,ADMSSM=PRS,
SENDDUSFF=N,AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,
FOREIGNFEND=N,FOREIGNIP="IP ADDRESS",OPRNOMINAL=Y:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<DCC>
Indicates whether or not the SDCC is to be used. Identifies the SDCC connection of the port. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<AREA>
The area ID and shows up only if the DCC is enabled. AREA is a string.
<SYNCMSG>
Synchronization status message. The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<SENDDUS>
The facility will send the DUS (Do not use for Synchronization) value as the SSM for that facility. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<PJMON>
Identifies an OC-N port PJMON. PJMON is an integer.
<SFBER>
Signal failure threshold. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
Signal degrade threshold. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<MODE>
OC-N port mode. the parameter type is OPTICAL_MODE, which is the facility's optical mode.
•
The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.
•
The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.
•
The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.
<MUX>
BLSR extension byte (supported only on the OC48AS card). MUX cannot be configured if:
•
•
•
The parameter type is MUX_TYPE, which is the BLSR extension type.
•
E2 byte (orderwire)
•
F1 byte (user)
•
K3 byte
•
Z2 byte
<SOAK>
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Defaults to 32. SOAK is an integer.
<OSFP>
The Open Shortest Path First discovery. Defaults to Y. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<LDCC>
The LDCC connection on the port. Defaults to N. the parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.
Note
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<NAME>
NAME is a string. It defaults to NULL. Its maximum length is 32 characters.
<CMDMDE>
Command Mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from IS-NR or OOS-AU,AINS service state. Defaults to NORM.
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<EXPTRC>
Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 card on the ONS 15454. Defaults to NULL. EXPTRC is a string.
<TRC>
The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 card on the ONS 15454. TRC is a string.
<TRCMODE>
Path trace mode. Applicable only to STS-level paths in SONET (STSn). Defaults to MAN. The parameter type is TRCMODE (trace mode).
•
Use the previously received path trace string as the expected string. Not applicable to MXP or TXP cards.
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP is detected.
•
Use the provisioned expected string as the expected string.
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP is detected.
•
Turn off path trace capability. Nothing will be reported.
<TRCFORMAT>
Trace message size. The parameter type is TRCFORMAT (trace format).
•
1 byte trace message
•
16 byte trace message
•
64 byte trace message
<ADMSSM>
SSM selectable value. It will only appear when SSM is disabled. Defaults to STU. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SONET.
•
Do Not Use For Synchronization
•
Primary Reference Source, Stratum 1 Traceable
•
Reserved For Network Synchronization Use
•
SONET Minimum Clock Traceable
•
Stratum 2 Traceable
•
Stratum 3 Traceable
•
Stratum 3E Traceable
•
Stratum 4 Traceable
•
Synchronized, Traceability Unknown
•
Transit Node Clock (2nd Generation Only)
<SENDDUSFF>
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<AISONLPBK>
The parameter type is AIS_ON_LPBK, which indicates if AIS is sent on a loopback.
•
AIS is sent on facility loopbacks.
•
AIS is sent on all loopbacks.
•
AIS is not sent on loopbacks.
•
AIS is sent on terminal loopbacks.
<FREQ>
The parameter type is OPTICAL_WLEN (optical wavelength).
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<LOSSB>
The parameter type is REACH (reach value)
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
<FOREIGNFEND>
Indicates whether the far-end NE on the DCC is a foreign NE. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<FOREIGNIP>
The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. FOREIGHNIP is a string.
<OPRNOMINAL>
Set to Y reads the current raw optical receive power and sets the raw OPR value as nomimal optical receive power. After executing this command, the OPRN is set to approximately 100.
Note
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute. Not supported for OPRNOMINAL.
•
Enable an attribute.
<PST>
Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.8 ED-ALS
(Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA) The Edit Automatic Laser Shutdown (ED-ALS) command is used to modify the ALS attributes of an OC-N facility and all the facilities that support the ALS feature. For MXP_2.5G_10E, TXP_MR_10E, MXP_2.5G_10G, TXP_MR_10G, TXP_MR_2.5G, and TXPP_MR_2.5G cards, this command is used to modify the ALS parameter of the OC48 and OC192 ports.
Usage Guidelines
None
CategoryPorts
SecurityProvisioning
Input FormatED-ALS:[<TID>]:<SRC>:<CTAG>:::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],
[ALSRCPW=<ALSRCPW>][:];Input ExampleED-ALS:CISCO:FAC-1-1:100:::ALSMODE=AUTO,ALSRCINT=130,ALSRCPW=35.1;
Input Parameters
<SRC>
Access identifier from the "AidUnionId" section.
<ALSMODE>
ALS is enabled or disabled. The parameter type is ALS_MODE, which is the working mode for automatic laser shutdown. Defaults to DISABLED.
•
Automatic
•
Disabled
•
Manual
•
Manual restart for test
<ALSRCINT>
ALS recovery interval. The range is 60 to 300 seconds. ALSRCINT is an integer. Defaults to 100.
<ALSRCPW>
ALS recovery pulse width. The range is 80 to 100 seconds. Defaults to 80. ALSRCWP is a float.
11.9 ED-APC
(Cisco ONS 15454) The Edit Amplification Power Control (ED-APC) command is used to modify the APC application attributes. The default value for an optional parameter is the NE default value. The value might not be the current value for the parameter. Use a RTRV-xx command to retrieve the current value.
Usage Guidelines
None
CategoryDWDM
SecurityProvisioning
Input FormatED-APC:[<TID>]::<CTAG>[:::APCENABLE=<APCENABLE>];
Input ExampleED-APC:PENNGROVE::CTAG:::APCENABLE=N;
Input Parameters
<APCENABLE>
Enable or disable the APC application. Default is N. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
11.10 ED-BITS
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Building Integrated Timing Supply (ED-BITS) command edits the building integrated timing supply (BITS) reference attributes.
Usage Guidelines
The SYNC-BITS1 and SYNC-BITS2 AIDs can be used to set the BITS-OUT port state. For a BITS facility, 64 k and 6 MHz are only applicable to ON. SSM selectable (ADMSSM) is not applicable to ONS 15600.
The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.
CategorySynchronization
SecurityProvisioning
Input FormatED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],
[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>][:<PST>];Input ExampleED-BITS:SONOMA:BITS-2:779:::LINECDE=AMI,FMT=ESF,LBO=0-133,SYNCMSG=N,
AISTHRSHLD=PRS,SABIT=BYTE-5,IMPEDANCE=120-OHM,BITSFAC=T1,ADMSSM=PRS:IS;Input Parameters
<AID>
Access identifier from the "BITS" section.
<LINECDE>
The parameter type is LINE_CODE (line code).
•
Line code value is AMI.
•
Line code value is B8ZS (binary 8-zero substitution)
<FMT>
Digital signal frame format. The parameter type is FRAME_FORMAT, which is the frame format for a T1 port.
•
Frame format is D4.
•
Frame format is Extended Superframe (ESF).
•
Frame format is unframed.
<LBO>
Line build-out settings. BITS line build-out. Default value is 0 to 133. LBO is an integer. The parameter type is BITS_LineBuildOut (BITS line build-out).
•
BITS line build-out range is 0-133.
•
BITS line build-out range is 134-266.
•
BITS line build-out range is 267-399.
•
BITS line build-out range is 400-533.
•
BITS line build-out range is 534-655.
<SYNCMSG>
Indicates if the BITS facility supports synchronization status message. Default is ON (Y). The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<AISTHRSHLD>
Alarm indication signal threshold. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SONET.
•
Do Not Use For Synchronization
•
Primary Reference Source, Stratum 1 Traceable
•
Reserved For Network Synchronization Use
•
SONET Minimum Clock Traceable
•
Stratum 2 Traceable
•
Stratum 3 Traceable
•
Stratum 3E Traceable
•
Stratum 4 Traceable
•
Synchronized, Traceability Unknown
•
Transit Node Clock (2nd Generation Only)
<SABIT>
When the frame format selection is E1, SABIT is the bit used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).
•
SABIT is BYTE-4.
•
SABIT is BYTE-5.
•
SABIT is BYTE-6.
•
SABIT is BYTE-7.
•
SABIT is BYTE-8.
<IMPEDANCE>
When the frame format selection is E1, IMPEDANCE is the terminal impedance of the BITS-IN port. The parameter type is IMPEDANCE, which is the terminal impedance of the BITS-IN port.
•
Impedance of 120 ohm
•
Impedance of 75 ohm
<BITSFAC>
BITS facility settings. BITS-2 always inherits the value of BITS-1. The parameter type is BITS_FAC (the BITS facility rate). 64 k and 6 MHz are only applicable to the ONS 15454.
•
2 MHz rate
•
64 K rate
•
6 MHz rate
•
E1 rate
•
T1 rate
<ADMSSM>
SSM selectable. Only applicable to BITS-IN when SSM is disabled.
Note
The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SONET.
•
Do Not Use For Synchronization
•
Primary Reference Source, Stratum 1 Traceable
•
Reserved For Network Synchronization Use
•
SONET Minimum Clock Traceable
•
Stratum 2 Traceable
•
Stratum 3 Traceable
•
Stratum 3E Traceable
•
Stratum 4 Traceable
•
Synchronized, Traceability Unknown
•
Transit Node Clock (2nd Generation Only)
<PST>
The primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
11.11 ED-BULKROLL-<OCN_TYPE>
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Bulkroll for OC12, OC192, OC3, or OC48 (ED-BULROLL-<OCN_TYPE>) command edits information about the rolling of traffic from one endpoint to another without interrupting service. This command uses the FORCE option to force a valid signal. The only parameters that can be edited are RMODE and FORCE. The time slots cannot be edited. Use ED-ROLL-<MOD_PATH> for single path level rolling.
Usage Guidelines
See Table 27-1 for supported modifiers by platform.
CategoryBridge and Roll
SecurityProvisioning
Input FormatED-BULKROLL-<OCN_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],[CMDMDE=<CMDMDE>];Input ExampleED-BULKROLL-OC48:CISCO:FAC-1-1:1:::RFROMSTART=STS-1-1-1,
RFROMEND=STS-1-1-11,CMDMDE=FRCD;Input Parameters
<FROM>
One of the endpoints. Access identifier from the "FACILITY" section for line level rolling and bulk rolling.
<RFROMSTART>
The starting time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (except VCM and FACILITY). Defaults to STS-<FROMSLOT>-<FROMPORT>-1, where <FROMSLOT> and <FROMPORT> are the slot and port of the <FROM> AID.
<RFROMEND>
The ending time slot in the source roll port. For bulk rolling only. The AID is from the "CrossConnectId1" section (except VCM and FACILITY). Defaults to STS-<FROMSLOT>-<FROMPORT>-N, where <FROMSLOT> and <FROMPORT> are the slot and port of the <FROM> AID and N is the value of OCn. (for example, OC48, n=48).
<CMDMDE>
Command execution mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
11.12 ED-CMD-SECU
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Command Security (ED-CMD-SECU) command edits the command security level of a particular command.
Usage Guidelines
None
CategorySecurity
SecuritySuperuser
Input FormatED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>;
Input ExampleED-CMD-SECU::INIT-REG:1::SU;
Input Parameters
11.13 ED-CRS-<PATH>
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Cross-Connect for STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, VT1, or VT2 (ED-CRS-<PATH>) command edits a cross-connection.
Usage Guidelines
See Table 27-1 for supported modifiers by platform.
Note
•
•
•
•
CategoryCross Connections
SecurityProvisioning
Input FormatED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::[<CCT>]:[ADD=<ADD>],
[REMOVE=<REMOVE>],[CKTID=<CKTID>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-CRS-STS3C::STS-1-1-1,STS-2-1-1:1:::ADD=STS-13-1-1,REMOVE=STS-2-1-1,CKTID=CKTID
CMDMDE=FRCD:IS,AINS;Input Parameters
<SRC>
Source AID from the "CrossConnectId1" section.
<DST>
Destination AID from the "CrossConnectId1" section.
<CCT>
Cross-connection. The parameter type is CCT which indicates the type of cross-connection to be created.
•
A unidirectional connection from a source tributary to a destination tributary
•
path protection multicast drop with (1-way) continue
•
path protection multicast end node (1-way continue)
•
A bidirectional connection between the two tributaries
Note
•
A unidirectional connection from a source tributary to a destination tributary on the protection path/fiber
•
A bidirectional connection between the two tributaries
•
A bidirectional drop and continue connection applicable only to path protection traditional and integrated DRIs
•
A bidirectional connection between the two tributaries on the extra protection path/fiber
•
Diagnostics cross-connect. Supports BERT (BLSR PCA diagnostics cross-connect).
<ADD>
AID from the "AidUnionId" section.
<REMOVE>
AID from the "AidUnionId" section.
<CKTID>
String
<CMDMDE>
Command Mode. The FRCD mode of operation is applicable only if the PST=OOS and SST=DSBLD.
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.14 ED-DAT
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Date and Time (ED-DAT) command edits the date and the time.
Usage Guidelines
None
CategorySystem
SecurityProvisioning
Input FormatED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>];
Input ExampleED-DAT:CISCO::1234::99-12-21,14-35-15;
Input Parameters
11.15 ED-DS1
(Cisco ONS 15454) The Edit DS1 (ED-DS1) command edits the test access attribute for DS1 access on a DS3XM card.
Usage Guidelines
•
•
•
•
•
•
–
–
–
•
CategoryPorts
SecurityProvisioning
Input FormatED-DS1:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[AISONLPBK=<AISONLPBK>],[MODE=<MODE>],[FMT=<FMT>];Input ExampleED-DS1:PETALUMA:DS1-2-1-12:123:::TACC=8,TAPTYPE=DUAL,AISONLPBK=OFF,
MODE=FDL,FMT=ESF;Input Parameters
<AID>
Access identifier from the "DS1" section.
<TACC>
TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. TACC is an integer.
<TAPTYPE>
TAP type. The parameter type is TAPTYPE (test access point type).
•
Dual FAD
•
Single FAD
<AISONLPBK>
The parameter type is AIS_ON_LPBK, which indicates whether AIS is sent on a loopback.
•
AIS is sent on facility loopbacks.
•
AIS is sent on all loopbacks.
•
AIS is not sent on loopbacks.
•
AIS is sent on terminal loopbacks.
<MODE>
Mode with which the command is to be implemented. DS1 path mode of the DS3XM-12 card. Defaults to FDL. The parameter type is DS1MODE, which is the DS1 path mode of the DS3XM-12 card.
•
The DS1 path of the DS3XM-12 card is in AT&T 54016 mode.
•
The DS1 path of the DS3XM-12 card is in FDL T1-403 mode.
<FMT>
Digital signal format. The DS1 path frame format of the DS3XM-12 card. Defaults to UNFRAMED. The parameter type is FRAME_FORMAT, which is the frame format for a T1 port.
•
Frame format is D4.
•
Frame format is ESF.
•
Frame format is unframed.
11.16 ED-EC1
(Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA) The Edit Electrical Carrier (ED-EC1) command edits the attributes of an EC1 card.
Usage Guidelines
This command is not allowed if the card is a protecting card.
CategoryPorts
SecurityProvisioning
Input FormatED-EC1:[<TID>]:<AID>:<CTAG>:::[PJMON=<PJMON>],[LBO=<LBO>],[SOAK=<SOAK>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[NAME=<NAME>],[EXPTRC=<EXPTRC>],
[TRC=<TRC>],[TRCMODE=<TRCMODE>],[<TRCFORMAT>],[AISONLPBK=<AISONLPBK>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-EC1:CISCO:FAC-1-1:123:::PJMON=0,LBO=0-225,SOAK=10,SFBER=1E-4,SDBER=1E-6,
NAME="EC1 PORT",EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,TRCFORMAT="16-BYTE,
AISONLPBK=AIS_ON_LPBK_ALL,CMDMDE=CMDMDE:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<PJMON>
A SONET pointer number (0 or 1) of an EC1 port. PJMON is an integer. It defaults to 0.
<LBO>
Line build-out settings. LBO is an integer. It defaults to 0-225. The parameter type is E_LBO (electrical signal line build-out).
•
Electrical signal line build-out range is 0-225.
•
Electrical signal line build-out range is 226-450.
<SOAK>
IS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer. Defaults to 32.
<SFBER>
Signal failure threshold. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
Signal degrade threshold. Defaults to 1E-7. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<NAME>
NAME is a string. Default value is NULL. Maximum length is 32 characters.
<EXPTRC>
String
<TRC>
String
<TRCMODE>
The parameter type is TRCMODE (trace mode).
•
Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIM-P is detected.
•
Use the provisioned expected string as the expected string.
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.
•
Turn off path trace capability. Nothing will be reported.
<TRCFORMAT>
Trace message size. The parameter type is TRCFORMAT (trace format).
•
1 byte trace message.
•
16 byte trace message.
•
64 byte trace message.
•
Enable an attribute.
<AISONLPBK>
Defaults to AIS_ONLPBK_FACILITY. The parameter type is AIS_ON_LPBK, which indicates whether AIS is sent on a loopback.
•
AIS is sent on facility loopbacks.
•
AIS is sent on all loopbacks.
•
AIS is not sent on loopbacks.
•
AIS is sent on terminal loopbacks.
<CMDMDE>
Command Mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.17 ED-EQPT
Note
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Equipment (ED-EQPT) command edits the attributes for a given equipment slot in the NE. If the card is in an equipment slot, this command is allowed only on the working AID.
The ED-EQPT command also modifies a shelf role from NC to SC on an NE configured in multi-shelf mode.
Usage Guidelines
The PROTID parameter indicates the unique identifier of the protection group (the protect card). "NULL" is a special value of the PROTID parameter and indicates the absence of a protection group. For the 1:1 protection type, RVRTV and RVTM parameters can be changed. For the 1:1 protection type, if the PROTID parameter is entered as "NULL", the protection group is deleted, as shown in the following command:
ED-EQPT:[<TID>]:SLOT-2:<CTAG>:::PROTID=NULL;
For the 1:N protection type, if the PROTID is "NULL," the AIDs in the list are removed from the protection group. If all the working cards are in the AID list, the protection group is deleted.
For example, if Slot 1, Slot 2, and Slot 4 were the only working cards in the protection group, the following command would remove Slot 4 from the protection group:
ED-EQPT:[<TID>]:SLOT-4:<CTAG>:::PROTID=NULL;
The protection group still has Slot 1 and Slot 2 as working cards.
The following command will remove all the other working cards in the above example and consequently, delete the protection group itself:
ED-EQPT:[<TID>]:SLOT-2&SLOT-1:<CTAG>:::PROTID=NULL;
The ED-EQPT command can be successfully executed on an already provisioned card to add or remove a working card from a protection group. This command is not valid on a protect card. Only cards can be added to or removed from a protection group. Protection type is immutable and is determined at the time of creation of a protection group (while adding the first working card). After it is provisioned, the equipment type cannot be edited either.
Examples of adding an existing card to a protection group using the ED-EQPT command:
1:1 protection group:
ED-EQPT::SLOT-2:12:::PROTID=SLOT-1,RVRTV=Y,RVTM=9.0;
1:N protection group:
ED-EQPT::SLOT-2:12:::PROTID=SLOT-3,PRTYPE=1-N,RVTM=6.5;
Error conditions for editing a 1:1 or 1:N protection group might be:
•
•
•
•
•
–
–
–
•
•
Note
Note
CategoryEquipment
SecurityProvisioning
Input FormatED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[PRTYPE=<PRTYPE>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[CMDMDE=<CMDMDE>],
[CARDMODE=<CARDMODE>],[PEERID=<PEERID>],[REGENNAME=<REGENNAME>],
[PWL=<PWL>],[RETIME=<RETIME>],[SHELFROLE=<SHELFROLE>],
[NEWSHELFID=<NEWSHELFID>]:[<PST>[,<SST>]];Input ExampleED-EQPT:CISCO:SLOT-2:123:::PROTID=SLOT-1,PRTYPE=1-1,RVRTV=Y,RVTM=9.0,
CMDMDE=FRCD,CARDMODE=DS3XM12-STS48,PEERID=SLOT-2,
REGENNAME="THIS GROUP",PWL=1530.33,RETIME=Y,SHELFROLE=SC,
NEWSHELFID=2:OOS,MT;Input Parameters
<AID>
Access identifier from the "EQPT" section.
<PROTID>
Protect card slot number of the protection group from the "PRSLOT" section.
<PRTYPE>
Protection group type. The parameter type is PROTECTION_GROUP.
•
1:1 protection group
•
1:N protection group
<RVRTV>
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<RVTM>
Revertive time. The parameter type is REVERTIVE_TIME.
•
Revertive time is 0.5 to 12.0 minutes.
<CMDMDE>
Command mode. Only applicable when creating or deleting a protection group (1:1 or 1:N) and/or adding cards to an existing protection group (1:N). Default is NORM. If creating or adding cards to a protection group, specifying FRCD requires the card to be physically plugged in and in the service state (IS). If removing cards from a protection group (1:N) or deleting the protection group (1:1, 1:N), specifying FRCD requires that there are no cross-connects (services) on the card.
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<CARDMODE>
Card mode.
Note
Note
The parameter type is CARDMODE (card mode). Card mode is applicable to cards that have multiple capabilities, for example, the ML-Series card can operate in two distinct modes: Linear Mapper Mode and L2/L3 Mode.
•
The optical amplifier is working as an optical booster
•
The optical amplifier is working as an optical pre-amplifier
•
DS1 mode on DS1E1 card.
•
E1 mode on DS1E1 card.
•
The DS3XM-12 card in the STS12 backplane rate mode
•
The DS3XM-12 card in the STS48 backplane rate mode
•
Line terminating mode
•
Section terminating mode
•
Transparent mode AIS
•
Transparent mode SQUELCH
•
FC_MR-4 card with distance extension support
•
FC_MR-4 card without distance extension support
•
ML-Series card in DOS field-programmable gate array (FPGA) using generic framing procedure (GFP) framing type
•
ML-Series card in DOS FPGA using high-level data link control (HDLC) framing type
•
4 Gbps Fibre Channel/FICON mode for the Cisco ONS 15454 10DME-C/10DME-L card supported on ports one and five
•
4 Gbps Fibre Channel/FICON supported on port one and Fibre Channel, GIGE and ISC modes for the Cisco ONS 15454 10DME-C/10DME-L card supported on ports five to eight
•
Fibre Channel, GIGE and ISC modes for the Cisco ONS 15454 10DME-C/10DME-L card supported on all eight ports
•
Fibre Channel, GIGE and ISC modes for the Cisco ONS 15454 10DME-C/10DME-L card supported on ports one to four and 4 Gbps Fibre Channel/FICON supported on port five
•
Fibre Channel, GIGE and ISC modes for the Cisco ONS 15454 10DME-C10DME-L card supported on all 8 ports (MXP-MR-10DME)
•
4 Gbps Fibre Channel/FICON mode for the Cisco ONS 15454 10DME-C10DME-L card supported on ports 1 and 5 (MXP-MR-10DME)
•
Fibre Channel, GIGE and ISC modes for the Cisco ONS 15454 10DME-C10DME-L card supported on ports 1 to 4 and 4 Gbps Fibre Channel/FICON supported on port 5 (MXP-MR-10DME)
•
4 Gbps Fibre Channel/FICON supported on port 1 and Fibre Channel, GIGE and ISC Modes for the Cisco ONS 15454 10DME-C10DME-L card supported on ports 5 to 8 (MXP-MR-10DME)
•
ESCON mode for the Cisco ONS 15454 MXP_2.5G_10G card
•
Fibre channel or GIGE mode for the MXP_2.5G_10G card
•
Mixed Fibre Channel, GIGE and ESCON modes for the Cisco ONS 15454 MXP_2.5G_10G card
<PEERID>
The regeneration peer slot from the "EQPT" section.
<REGENNAME>
The name of a regeneration group. REGENNAME is a string.
<PWL>
Provisioned wavelength. TL1 will not set a default PWL value at the management level if no PWL value is given. The parameter type is OPTICAL_WLEN (optical wavelength),
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<RETIME>
Indicates if retiming is needed. Applicable only to the DS1/E1-56 card (ONS 15454). The parameter type is YES_NO, which indicates whether the user's password is about to expire, the user is logged into the NE, or the user is locked out of the NE.
•
No
•
Yes
<SHELFROLE>
The role of the shelf in the context of the node. When it is omitted it defaults to SC. The parameter is SHELF_ROLE.
•
The shelf behaves as a node controller.
•
The shelf behaves as a shelf controller.
<NEWSHELFID>
(Optional) New shelf identifier is used to change the value of the shelf identifier for the addressed shelf. The value must be different by one and can be in the range from two to eight. This field can only be changed if (in the same command) the SHELFROLE is equal to SC. Integer.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.18 ED-FAC
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Facility (ED-FAC) command provisions the payload (or signal) type of facility. The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command to retrieve them.
Usage Guidelines
None
CategoryPorts
SecurityProvisioning
Input FormatED-FAC:[<TID>]:<SRC>:<CTAG>:::[PAYLOAD=<PAYLOAD>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-FAC:CISCO:FAC-3-9:2222:::PAYLOAD=E4-FRAMED,CMDMDE=CMDMDE:IS,AINS;
Input Parameters
<SRC>
Source access identifier from the "FACILITY" section.
<PAYLOAD>
The payload for the card. The parameter type is PAYLOAD, which identifies the payload type.
•
10 Gigabit Ethernet Fibre Channel mode
•
10 Gigabit Ethernet
•
1 Gigabit Fibre Channel mode
•
1 Gigabit FICON mode
•
2 Gigabit Fibre Channel mode
•
2 Gigabit FICON mode
•
DS3 mode
•
Video mode
•
EC1 mode
•
ESCON mode
•
ETR/CLO payload mode
•
Gigabit Ethernet Payload
•
HDTV mode
•
ISC1 Mode
•
ISC3 Mode
•
SONET OC-12 mode
•
SONET OC-3 mode
•
SONET OC-48 mode
•
Pass through mode
•
SDI-D1-Video mode
•
SONET Payload Mode
CMDMDE
Command Mode. Defaults to NORM. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
PST
Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
SST
Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.19 ED-FFP-<MOD2DWDMPAYLOAD>
(Cisco ONS 15454) The Edit Facility Protection Group for 10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, D1VIDEO, DV6000, ETRCLO, GIGE, HDTV, or ISC1 (ED-FFP-<MOD2DWDMPAYLOAD>) command edits a Y-cable protection group on client facilities.
Usage Guidelines
None
CategoryDWDM
SecurityProvisioning
Input FormatED-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:];Input ExampleED-FFP-CLNT:CISCO:FAC-1-1:100:::PROTID=DC-METRO,RVRTV=N,RVTM=1.0,PSDIRN=BI;
Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<PROTAID>
The protection group identifier (protection group name). Defaults to the protecting port AID of the protection group. PROTAID can have a maximum length of 32 characters. It is a string.
<RVRTV>
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. Only applies to path protection configurations. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
RVTM
Revertive time. RVTM is not allowed to be set while "RVRTV" is N. Only applies to path protection configurations. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
PSDIRN
Protection switch operation. Identifies the switching mode. Defaults to UNI.
Note
The parameter type is UNI_BI (unidirectional switch operations).
•
Bidirectional protection switching
•
Unidirectional protection switching
11.20 ED-FFP-<OCN_TYPE>
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Facility Protection Group for OC3, OC12, OC48, or OC192 (ED-FFP-<OCN_TYPE>) command edits the optical facility protection.
Usage Guidelines
See Table 27-1 for supported modifiers by platform.
Note
•
•
CategoryProtection
SecurityProvisioning
Input FormatED-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>],[VRGRDTM=<VRGRDTM>],
[DTGRDTM=<DTGRDTM>],[RCGRDTM=<RCGRDTM>][:];Input ExampleED-FFP-OC3:PETALUMA:FAC-1-1:1:::PROTID=PROT_NAME,RVRTV=Y,RVTM=1.0,
PSDIRN=BI,VRGRDTM=0.5,DTGRDTM=1.0,RCGRDTM=1.0;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<PROTAID>
The protection group identifier (protection group name). PROTAID can have a maximum length of 32 characters. It is a string.
<RVRTV>
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<RVTM>
Revertive time. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
<PSDIRN>
Protection switch operation. Indicates the switch mode. Defaults to UNI. The parameter type is UNI_BI (unidirectional and bidirectional switch operations).
•
Bidirectional protection switching
•
Unidirectional protection switching
<VRGRDTM>
Verification guard timer. Only applicable to optimized 1+1. The parameter type is VERIFICATION_GUARD_TIMER (optimized 1+1 verification guard timer).
•
500 ms
•
1 second
<DTGRDTM>
Detection guard timer. Only applicable to optimized 1+1. The parameter type is DETECTION _GUARD_TIMER (optimized 1+1 detection guard timer).
•
0 seconds
•
50 ms
•
100 ms
•
500 ms
•
1 second to 5 seconds
<RCGRDTM>
Recovery guard timer. Only applicable to optimized 1+1. The parameter type is RECOVERY_GUARD_TIMER (optimized 1+1 recovery guard timer).
•
0 seconds
•
50 ms
•
100 ms
•
500 ms
•
1 second to 10 seconds
11.21 ED-FFP-OCH
(Cisco ONS 15454) The Edit Facility Protection Group Optical Channel (ED-FFP-OCH) command changes the provisioning for the default protection group on the DWDM port of a TXP_MR_2.5G and TXPP_MR_2.5G card.
Usage Guidelines
None
CategoryDWDM
SecurityProvisioning
Input FormatED-FFP-OCH:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[RVRTV=<RVRTV>],
[RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:];Input ExampleED-FFP-OCH:VA454-22:CHAN-2-2:100:::PROTID="FIXEDPROTECTION",RVRTV=N,
RVTM=1.0,PSDIRN=BI;Input Parameters
<AID>
Access identifier from the "CHANNEL" section.
<PROTAID>
The protection group identifier (protection group name). PROTAID is a string.
<RVRTV>
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<RVTM>
Revertive time. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes
<PSDIRN>
Protection switch operation. The parameter type is TRANS_MODE (G1000 transponder mode)
•
Bidirectional
•
Not in transponder mode
•
Unidirectional
11.22 ED-FSTE
(Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA) The Edit Fast Ethernet (ED-FSTE) command edits the front-end port information of the fast (10/100 Mbps) Ethernet card
Usage Guidelines
The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command to retrieve them.
Note
CategoryPorts
SecurityProvisioning
Input FormatED-FSTE:[<TID>]:<AID>:<CTAG>:::[FLOW=<FLOW>],[EXPDUPLEX=<EXPDUPLEX>],
[EXPSPEED=<EXPSPEED>],[VLANCOS=<VLANCOS>],[IPTOS=<IPTOS>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];Input ExampleED-FSTE:CISCO:FAC-1-1:123:::FLOW=FLOW,EXPDUPLEX=EXPDUPLEX,
EXPSPEED=EXPSPEED, VLANCOS=VLANCOS,IPTOS=IPTOS,
NAME="FSTE PORT",CMDMDE=CMDMDE,SOAK=32:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<FLOW>
Flow control. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<EXPDUPLEX>
Ethernet duplex mode. The parameter type is ETHER_DUPLEX (duplex mode).
•
Auto mode
•
Full mode
•
Half mode
<EXPSPEED>
Ethernet speed. The parameter type is ETHER_SPEED (Ethernet speed).
•
100 Mbps
•
10 Gbps
•
10 Mbps
•
1 Gbps
•
Auto
<VLANCOS>
Priority queuing threshold based on VLAN class of service of incoming Ethernet packets. Default value is 1175. VLANCOS is an integer.
<IPTOS>
Priority queuing threshold based on IP type of service of incoming Ethernet packets. Default value is 368. IPTOS is an integer.
<NAME>
Name. NAME is a string.
<CMDMDE>
Command Mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from IS-NR or OOS-AU,AINS service state. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<SOAK>
OOS-AINS to IS transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.23 ED-G1000
(Cisco ONS 15454) The Edit G1000 (ED-G1000) command edits the attributes related to a G1000 port.
Usage Guidelines
The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.
CategoryPorts
SecurityProvisioning
Input FormatED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>],[FLOW=<FLOW>],
[LOWMRK=<LOWMRK>],[HIWMRK=<HIWMRK>],[AUTONEG=<AUTONEG>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];Input ExampleED-G1000:TID:FAC-1-1:CTAG:::MFS=1548,FLOW=Y,LOWMRK=20,HIWMRK=492,
AUTONEG=Y,NAME="G1000 PORT",CMDMDE=FRCD,SOAK=32:OOS,DSBLD;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<MFS>
Maximum frame size. the parameter type is MFS_TYPE, which is the maximum frame size used by an Ethernet card.
•
Normal frame size
•
Jumbo frame size
<FLOW>
Flow control. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<LOWMRK>
Low watermark value. LOWMRK is an integer. Defaults to 25. LOWMRK is available in Software Release 4.0.1 and later.
<HIWMRK>
High watermark value. HIWMRK is an integer. Defaults to 485.
<AUTONEG>
Automatic negotiation. Defaults to Y. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<NAME>
Name. NAME is a string. Default is NULL. Maximum length is 32 characters.
<CMDMDE>
Command execution mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<SOAK>
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer. Defaults to 32.
<ENCAP>
Encapsulation. ENCAP is a string.
<PST>
Primary state. Defaults to OOS. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. Defaults to DSBLD. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.24 ED-GFP
(Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Generic Framing Protocol (ED-GFP) command applies to the ONS 15454 CE-100T-8 card, FC_MR-4 card, and CE-1000-4 card, the ONS 15310-CL CE-100T-8 card, and the ONS 15600 ASAP card. It changes GFP parameters.
Usage Guidelines
•
•
•
CategoryPorts
SecurityProvisioning
Input FormatED-GFP:[<TID>]:<AID>:<CTAG>:::[FCS=<FCS>],[AUTOTHGFPBUF=<AUTOTHGFPBUF>],
[GFPBUF=<GFPBUF>],[FILTER=<FILTER>];Input ExampleED-GFP:CISCO:VFAC-1-0:123:::FCS=N,AUTOTHGFPBUF=Y,GFPBUF=16,FILTER=EGRESS;
Input Parameters
<AID>
Access identifier from the "FACILITY" section.
Note
<FCS>
Payload frame check sequence. The parameter type is FCS (frame check sequence).
•
Frame check sequencing using 16 bits
•
Frame check sequencing using 32 bits
•
No frame check sequence
<AUTOTHGFPBUF>
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<FILTER>
The parameter type is GFP_FILTER, which is the filter feature in GFP.
•
Activate filter feature on egress port.
•
Turn off filter feature.
11.25 ED-HDLC
(Cisco ONS 15600) The Edit High-Level Data Link Control (ED-HDLC) command edits HDLC-related attributes for HDLC-encapsulated payloads.
Usage Guidelines
None
CategoryPorts
SecurityProvisioning
Input FormatED-HDLC:[<TID>]:<SRC>:<CTAG>[:::FCS=<FCS>];
Input ExampleED-HDLC:TID:VFAC-SLOT-PORT:CTAG:::FCS=FCS-16;
Input Parameters
<SRC>
Access identifier from the "FACILITY" section. The ONS 15600 ASAP card uses the VFAC AID.
<FCS>
Payload frame check sequence. The parameter type is FCS (frame check sequence).
•
Frame check sequence using 16 bits
•
Frame check sequence using 32 bits
•
No frame check sequence
11.26 ED-LNK
(Cisco ONS 15454) The Edit Link (ED-LNK) command edits an optical link state.
Usage Guidelines
The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.
CategoriesDWDM
SecurityProvisioning
Input FormatED-LNK:[<TID>]:<FROM>,<TO>:<CTAG>:::[CMDMDE=<CMDMDE>]:
[<PST>[,<SST>]];Input ExampleED-LNK:PENNGROVE:BAND-6-1-TX,BAND-13-1-RX:114:::CMDMDE=CMDMDE:
IS,AINS;Input Parameters
<FROM>
Identifier at one end of the optical link from the "BAND" section.
<TO>
Identifier at the other end of the optical link from the "BAND" section.
<CMDMDE>
Command Mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from IS-NR or OOS-AU,AINS service state.
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state.
Note
The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state.
Note
The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.27 ED-LNKTERM
(Cisco ONS 15454, ONS 15327, ONS 15310-CL) The Edit Provisionable Patchcord Termination (ED-LNKTERM) command edits the attributes of a provisionable patchcord that has already been created. Only the remote end attributes (REMOTENODE and REMOTELNKTERMID) can be edited.
Usage Guidelines
•
•
•
•
CategoryProvisionable Patchcords
SecurityProvisioning
Input FormatED-LNKTERM:[<TID>]:<AID>:<CTAG>:::[REMOTENODE=<REMOTENODE>],
[REMOTELNKTERMID=<REMOTELNKTERMID>];Input ExampleED-LNKTERM::LNKTERM-1:CTAG:::REMOTENODE=172.20.208.226,
REMOTELNKTERMID=25;Input Parameters
<AID>
Access identifier from the "LNKTERM" section. Indicates a link (provisionable patchcord) termination on the local node.
<REMOTENODE>
The node where the other end of the provisionable patchcord resides. This can be an IP address or a valid TID. Defaults to the IP address of the local node/existing value. REMOTENODE is a string.
<REMOTELNKTERMID>
The corresponding provisionable patchcord termination on the remote node (as specified by the REMOTENODE parameter). Integer value within the range of 1 to 65535. Defaults to the existing value.
11.28 ED-NE-GEN
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Network Element General (ED-NE-GEN) command edits the node attributes of the NE.
Usage Guidelines
•
•
•
•
•
•
Caution
CategorySystem
SecuritySuperuser
Input FormatED-NE-GEN:[<TID>]::<CTAG>:::[NAME=<NAME>],[IPADDR=<IPADDR>],
[IPMASK=<IPMASK>],[DEFRTR=<DEFRTR>],[IIOPPORT=<IIOPPORT>],
[NTP=<NTP>],[ISPROXYSERVER=<ISPROXYSERVER>],[ISFIREWALL=<ISFIREWALL>],
[SUPPRESSIP=<SUPPRESSIP>],[MODE=<MODE>];Input ExampleED-NE-GEN:CISCO::123:::NAME=NODENAME,IPADDR=192.168.100.52,
IPMASK=255.255.255.0,DEFRTR=192.168.100.1,IIOPPORT=57790,
NTP=192.168.100.52,ISPROXYSERVER=YES,ISFIREWALL=YES,SUPPRESSIP=NO,
MODE=SINGLESHELF;Input Parameters
11.29 ED-NE-PATH
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA) The Edit Network Element Path (ED-NE-PATH) command edits the path attributes of the NE.
Usage Guidelines
The default value for an optional parameter is the NE default value.
CategorySystem
SecurityProvisioning
Input FormatED-NE-PATH:[<TID>]::<CTAG>:::[PDIP=<PDIP>],[XCMODE=<XCMODE>];
Input ExampleED-NE-PATH:::CTAG:::PDIP=Y,XCMODE=MIXED;
Input Parameters
11.30 ED-NE-SYNCN
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Network Element Synchronization (ED-NE-SYNCN) command edits the synchronization attributes of the NE.
Usage Guidelines
The existing external and line modes have the same functionality in all ONS 15454 4.x and 5.x releases:
•
•
•
Note
CategorySynchronization
SecurityProvisioning
Input FormatED-NE-SYNCN:[<TID>]:[<AID>]:<CTAG>:::[TMMD=<TMMD>],[SSMGEN=<SSMGEN>],
[QRES=<QRES>],[RVRTV=<RVRTV>],[RVTM=<RVTM>];Input ExampleED-NE-SYNCN:CISCO::123:::TMMD=LINE,SSMGEN=GEN1,QRES=ABOVE-PRS,RVRTV=Y,
RVTM=8.0;ED-NE-SYNCN:CISCO:SHELF-2:123:::TMMD=LINE,SSMGEN=GEN1,QRES=ABOVE-PRS,
RVRTV=Y,RVTM=8.0;Input Parameters
<AID>
The node or shelf access identifier from the "SHELF" section. If omitted it addresses the node or first shelf of the node. Must not be null.
<TMMD>
Timing mode. A null value is equivalent to ALL. Defaults to EXTERNAL. The parameter type is TIMING_MODE, which is the timing mode for the current node.
•
The node derives its clock from the BITS input.
•
The node derives its clock from the SONET lines.
•
The node derives its clock from the mixed timing mode.
<SSMGEN>
Synchronization status message set. Defaults to GEN1. A null value is equivalent to ALL. The default is ABOVE-STU. The parameter type is SYNC_GENERATION (synchronization status message set generation).
•
First generation SSM set
•
Second generation SSM set
<QRES>
Quality of the RES. A null value is equivalent to ALL. Defaults to DUS. The parameter type is SYNC_QUALITY_LEVEL, which is the network synchronization quality level.
•
Better than primary reference source. Valid setting for Generation-1 and Generation-2 SSM Set.
•
Between SMC and ST3. Valid setting for Generation-1 and Generation-2 SSM Set.
•
Between ST2 and STU. Valid setting for Generation-1 and Generation-2 SSM Set.
•
For Generation-1 SSM set, between ST3 and ST2. For Generation-2 SSM set, between ST3 and ST3E.
•
Between ST3E and TNC. Valid setting only for Generation-2 SSM set.
•
Between ST4 and ST3. Valid setting for Generation-1 and Generation-2 SSM Set.
•
Between STU and PRS. Valid setting for Generation-1 and Generation-2 SSM Set. This is default setting.
•
Between TNC and ST2. Valid setting only for Generation-2 SSM set.
•
Below ST4 but still usable. Valid setting for Generation-1 and Generation-2 SSM Set.
•
Disable the RES message by equating it to DUS. Valid setting for Generation-1 and Generation-2 SSM Set.
<RVRTV>
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. A null value is equivalent to ALL. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<RVTM>
Revertive time. A null value is equivalent to ALL. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
11.31 ED-OCH
(Cisco ONS 15454) The Edit Optical Channel (ED-OCH) command edits the attributes (service parameters) and state of an OCH facility. Refer to the Cisco ONS SONET TL1 Reference Guide for specific card provisioning rules.
Usage Guidelines
Primary=OOS and secondary=AINS states do not apply to Ethernet mode.
CategoryDWDM
SecurityProvisioning
Input FormatED-OCH:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[EXPWLEN=<EXPWLEN>],
[VOAATTN=<VOAATTN>],[VOAPWR=<VOAPWR>],[CALOPWR=<CALOPWR>],
[CHPOWER=<CHPOWER>],[NAME=<PORTNAME>],[SFBER=<SFBER>],[SDBER=<SDBER>],
[COMM=<COMM>],[GCCRATE=<GCCRATE>],[OSDBER=<OSDBER>],[DWRAP=<DWRAP>],
[FEC=<FEC>],[PAYLOADMAP=<PAYLOADMAP>],[MACADDR=<MACADDR>],
[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[SOAK=<SOAK>],[OSPF=<OSPF>],
[MFS=<MFS>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-OCH:CISCO:CHAN-6-2:114:::RDIRN=W-E,EXPWLEN=1530.32,VOAATTN=2.5,
VOAPWR=7.5,CALOPWR=0,CHPOWER=2.0,NAME="NYLINE",SFBER=1E-5,
SDBER=1E-6,COMM=DCC,GCCRATE=192K,OSDBER=1E-6,DWRAP=Y,FEC=STD,
PAYLOADMAP=ASYNCH,MACADDR=00-0E-AA-BB-CC-DD,SYNCMSG=N,
SENDDUS=Y,SOAK=10,OSPF=Y,MFS=2152,CMDMDE=CMDMDE:IS,AINS;Input Parameters
AID
Access identifier from the "CHANNEL" section.
RDIRN
Ring directionality of the optical line. The parameter type is RDIRN_MODE, which is the optical ring directionality.
•
The direction of the signal is from east to west (clockwise).
•
The direction of the signal is from west to east (counterclockwise).
EXPWLEN
Optical wavelength for this port. Applicable only to the following cards: optical service channel cards, optical amplifier cards, dispersion compensation units, multiplexer cards, demultiplexer cards and optical add/drop multiplexing (OADM) cards. The parameter type is OPTICAL_WLEN (optical wavelength).
•
Wavelength 1310
•
Wavelength 1470
•
Wavelength 1490
•
Wavelength 1510
•
Wavelength 1529.55
•
Wavelength 1529.94
•
Wavelength 1530
•
Wavelength 1530.33
•
Wavelength 1530.73
•
Wavelength 1531.12
•
Wavelength 1531.51
•
Wavelength 1531.90
•
Wavelength 1532.29
•
Wavelength 1532.68
•
Wavelength 1533.07
•
Wavelength 1533.47
•
Wavelength 1533.86
•
Wavelength 1534.25
•
Wavelength 1534.64
•
Wavelength 1535.04
•
Wavelength 1535.43
•
Wavelength 1535.82
•
Wavelength 1536.22
•
Wavelength 1536.61
•
Wavelength 1537
•
Wavelength 1537.40
•
Wavelength 1537.79
•
Wavelength 1538.19
•
Wavelength 1538.58
•
Wavelength 1538.98
•
Wavelength 1539.37
•
Wavelength 1539.77
•
Wavelength 1540.16
•
Wavelength 1540.56
•
Wavelength 1540.95
•
Wavelength 1541.35
•
Wavelength 1541.75
•
Wavelength 1542.14
•
Wavelength 1542.35
•
Wavelength 1542.54
•
Wavelength 1542.94
•
Wavelength 1543.33
•
Wavelength 1543.73
•
Wavelength 1544.13
•
Wavelength 1544.53
•
Wavelength 1544.92
•
Wavelength 1545.32
•
Wavelength 1545.72
•
Wavelength 1546.12
•
Wavelength 1546.52
•
Wavelength 1546.92
•
Wavelength 1547.32
•
Wavelength 1547.72
•
Wavelength 1548.12
•
Wavelength 1548.51
•
Wavelength 1548.92
•
Wavelength 1549.32
•
Wavelength 1549.71
•
Wavelength 1500
•
Wavelength 1550.12
•
Wavelength 1550.52
•
Wavelength 1550.92
•
Wavelength 1551.32
•
Wavelength 1551.72
•
Wavelength 1552.12
•
Wavelength 1552.52
•
Wavelength 1552.93
•
Wavelength 1553.33
•
Wavelength 1553.73
•
Wavelength 1554.13
•
Wavelength 1554.13
•
Wavelength 1554.94
•
Wavelength 1555.34
•
Wavelength 1555.75
•
Wavelength 1556.15
•
Wavelength 1556.55
•
Wavelength 1556.96
•
Wavelength 1557.36
•
Wavelength 1557.77
•
Wavelength 1558.17
•
Wavelength 1558.58
•
Wavelength 1558.98
•
Wavelength 1559.39
•
Wavelength 1559.79
•
Wavelength 1560.20
•
Wavelength 1560.61
•
Wavelength 1561.01
•
Wavelength 1561.42
•
Wavelength 1561.83
•
Wavelength 1570
•
Wavelength 1570.83
•
Wavelength 1571.24
•
Wavelength 1571.65
•
Wavelength 1572.06
•
Wavelength 1572.48
•
Wavelength 1572.89
•
Wavelength 1573.30
•
Wavelength 1573.71
•
Wavelength 1574.13
•
Wavelength 1574.54
•
Wavelength 1574.95
•
Wavelength 1575.37
•
Wavelength 1575.78
•
Wavelength 1576.20
•
Wavelength 1576.61
•
Wavelength 1577.03
•
Wavelength 1577.44
•
Wavelength 1577.86
•
Wavelength 1578.27
•
Wavelength 1578.69
•
Wavelength 1579.10
•
Wavelength 1579.52
•
Wavelength 1579.93
•
Wavelength 1580.35
•
Wavelength 1580.77
•
Wavelength 1581.18
•
Wavelength 1581.60
•
Wavelength 1582.02
•
Wavelength 1582.44
•
Wavelength 1582.85
•
Wavelength 1583.27
•
Wavelength 1583.69
•
Wavelength 1584.11
•
Wavelength 1584.53
•
Wavelength 1584.95
•
Wavelength 1585.36
•
Wavelength 1585.78
•
Wavelength 1586.20
•
Wavelength 1586.62
•
Wavelength 1587.04
•
Wavelength 1587.46
•
Wavelength 1587.88
•
Wavelength 1588.30
•
Wavelength 1588.73
•
Wavelength 1589.15
•
Wavelength 1589.57
•
Wavelength 1589.99
•
Wavelength 1590
•
Wavelength 1590.41
•
Wavelength 1590.83
•
Wavelength 1591.26
•
Wavelength 1591.68
•
Wavelength 1592.10
•
Wavelength 1592.52
•
Wavelength 1592.95
•
Wavelength 1593.37
•
Wavelength 1593.79
•
Wavelength 1594.22
•
Wavelength 1594.64
•
Wavelength 1595.06
•
Wavelength 1595.49
•
Wavelength 1596.34
•
Wavelength 1596.76
•
Wavelength 1597.19
•
Wavelength 1597.62
•
Wavelength 1598.04
•
Wavelength 1598.47
•
Wavelength 1598.89
•
Wavelength 1599.32
•
Wavelength 1599.75
•
Wavelength 1600.06
•
Wavelength 1601.03
•
Wavelength 1601.46
•
Wavelength 1601.88
•
Wavelength 1602.31
•
Wavelength 1602.74
•
Wavelength 1603.17
•
Wavelength 1603.60
•
Wavelength 1604.03
•
Wavelength 1610
•
Use Tunable Wavelength 1
<VOAATTN>
The value of calibrated attenuation for the variable optical attenuator (VOA). It is expressed in dBm. For the following cards, the range is 0.0 to +30.0: optical service channel, optical amplifier, dispersion compensation units, multiplexer, demultiplexer, and OADM. Not supported for TXP or MXP cards. VOAATIN is a float.
<VOAPWR>
The value of calibrated output power that the VOA is going to set as a result of its attenuation. Applicable only to the following cards: optical service channel, optical amplifier, dispersion compensation units, multiplexer, demultiplexer, and OADM. VOAPWR is a float.
<CALOPWR>
The value of the calibrated optical power expected for the line added to the calculated value, which equals the total expected output power. Expressed in dBm. Applicable only to the following cards: optical service channel, optical amplifier, dispersion compensation units, multiplexer, demultiplexer, and OADM. Defaults to 0 dBm. CALOPWR is a float.
<CHPOWER>
The value of per-channel optical power expected to the OCH drop port of an AD-4C unit. CHPOWER is a float expressed in dBm. The parameter type is REVERTIVE_TIME (revertive time).
•
Revertive time is 0.5 to 12.0 minutes.
<PORTNAME>
Port name. PORTNAME is a string.
<SFBER>
Signal failure threshold for the SONET payload. Can only be provisioned on the working port. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
Signal degrade threshold for the SONET payload. Can only be provisioned on the working port. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<COMM>
The generic communications channel (GCC) or data communications channel (DCC) is enabled or disabled. The GCC can be enabled only if the digital wrapper has been enabled for the card. The default is NONE.
On an MXP_2.5G_10G or TXP_MR_10G client port, only the DCC can be provisioned, if the termination mode is not transparent and the payload is SONET. On an MXP_2.5G_10G or TXP_MR_10G DWDM port, the DCC can be enabled only if the ITU-T G.709 is not enabled, if the payload is SONET, and the termination mode is not transparent. On an MXP_2.5G_10G or TXP_MR_10G DWDM port, the GCC can be enabled if there is no DCC and the ITU-T G.709 flag is enabled. On a TXP/MXP DWDM port, the DCC/GCC can be disabled only if no provisionable patchcord terminations are provisioned on the trunk port.
The parameter type is COMM_TYPE, which is the out of band communications channel termination type.
•
Section DCC type.
•
Generic communication channel (OTN) type.
•
Disable DCC or GCC if enabled.
<GCCRATE>
The data rate of the GCC traffic. The default is 192 Kbps. For MXP_2.5G_10G and TXP_MR_10G cards, this applies only to the DWDM port.
Note
Parameter type is GCCRATE, which is the data rate of the GCC traffic.
•
192 kbps
•
576 kbps
<OSDBER>
OTN SDBER. Can only be provisioned on the working port. Defaults to 1E-7
Parameter type is SD_BER—the threshold for declaring signal degrade on a facility or path
•
SDBER is 1E-5
•
SDBER is 1E-6
•
SDBER is 1E-7
•
SDBER is 1E-8
•
SDBER is 1E-9
<DWRAP>
The ITU-T G.709 digital wrapper. It is either on or off. The system default is ON. For MXP_2.5G_10G and TXP_MR_10G cards, this applies only to the DWDM port.
To enable ITU-T G.709:
•
•
To disable ITU-T G.709:
•
•
•
•
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<FEC>
Forward error correction. It can be enabled only if the ITU-T G.709 is turned ON. It is either off or enabled in standard or enhanced mode. The system default is standard FE enabled. The FEC level performance monitoring (PM) and thresholds apply if the FEC is turned ON. The parameter type is FEC_MODE, which specifies the type of forward error correction.
•
Enhanced FEC is enabled.
•
FEC is disabled.
•
Standard FEC is enabled.
<PAYLOADMAP>
The type of payload mapping. It can be enabled only if the ITU-T G.709 is turned ON and FEC is enabled. The parameter type is PAYLOAD_MAPPING (payload mapping mode).
•
Asynchronous mapping mode
•
ODU multiplex structure mode
•
Synchronous mapping mode
<MACADDR>
MAC address for the 10GigE payload. MACADDR is a string.
<SYNCMSG>
The facility be enabled to provide the synchronization clock. This does not apply to the TXPD-10G card. This applies to an MXPD-10G card, only if the payload is SONET/SDH and the card termination mode is as follows:
•
•
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<SENDDUS>
The facility sends out a Do not Use for Sync message. This does not apply to the TXPD-10G card. This applies to an MXPD-10G card only if the payload is SONET/SDH and the card termination mode is as follows:
•
•
The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<SOAK>
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<OSPF>
Open Shortest Path First. The parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.
•
The ring does not support the extended K1/K2/K3 protocol.
•
The ring does support the extended K1/K2/K3 protocol.
<MFS>
Integer
<CMDMDE>
Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.32 ED-OCHCC
(Cisco ONS 15454) The Edit Optical Channel Client Connection (ED-OCHCC) command edits the OCH client connection.
Usage Guidelines
•
•
•
CategoryDWDM
SecurityProvisioning
Input FormatED-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-OCHCC:VA454-22:FAC-2-1-1:116:::CKTID=OCHCC,CMDMDE=FRCD:OOS,DSBLD;
Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<CKTID>
Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48. If CKTID is empty or null the CKTID field will not be displayed.
<CMDMDE>
The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.
•
Force the system to override a state in which the command would normally be denied.
•
Execute the command normally. Do not override any conditions that may make the command fail.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity. The default is IS.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ. The default is AINS.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.33 ED-OCHNC
(Cisco ONS 15454) The Edit Optical Channel Network Connection (ED-OCHNC) command edits the OCH network connection.
Usage Guidelines
•
•
•
CategoryDWDM
SecurityProvisioning
Input FormatED-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-OCHNC:VA454-22:CHANWL-1-3-TX-1530.33,
LINEWL-4-1-RX-1530.33:116:::CKTID=CIRCUIT,CMDMDE=FRCD:OOS,DSBLD;Input Parameters
<SRC>
Source access identifier from the "CHANNEL" section. In 2-way wavelength connection sources both directions need to be indicated.
<DST>
Destination access identifier from the "LINEWL" section. In 2-way wavelength connection sources both directions need to be indicated.
<CKTID>
Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48. If CKTID is empty or null the CKTID field will not be displayed.
<CMDMDE>
The parameter type is command mode, which forces the system to execute a given command regardless of any standing conditions. NORM mode is the default behavior for all commands but you can specify FRCD to force the system to override a state in which the command would normally be denied.
•
Force the system to override a state in which the command would normally be denied.
•
Execute the command normally. Do not override any conditions that may make the command fail.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity. The default is IS.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ. The default is AINS.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.34 ED-OMS
(Cisco ONS 15454) The Edit Optical Multiplex Section (ED-OMS) command edits the attributes (service parameters) and state of an OMS facility.
Usage Guidelines
None
CategoryDWDM
SecurityProvisioning
Input FormatED-OMS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[EXPBAND=<EXPBAND>],
[VOAATTN=<VOAATTN>],[VOAPWR=<VOAPWR>],[CALOPWR=<CALOPWR>],
[CHPOWER=<CHPOWER>],[NAME=<NAME>],[SOAK=<SOAK>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-OMS:PENNGROVE:BAND-6-1:114:::RDIRN=W-E,EXPBAND=1530.32-1532.68,
VOAATTN=2.5,VOAPWR=7.5,CALOPWR=0.0,CHPOWER=2.0,NAME="OMS PORT",
SOAK=8,CMDMDE=CMDMDE:IS,AINS;Input Parameters
<AID>
Access identifier from the "BAND" section.
<RDIRN>
Ring directionality of the optical line. The parameter type is RDIRN_MODE, which is the optical ring directionality.
•
The direction of the signal is from east to west (clockwise).
•
The direction of the signal is from west to east (counterclockwise).
<EXPBAND>
The expected value of the optical band for this port. The parameter type is OPTICAL_BAND (optical band).
•
Band 1
•
Band 2
•
Band 3
•
Band 4
•
Band 5
•
Band 6
•
Band 7
•
Band 8
•
This band is not yet configured/retrieved from unit.
<VOAATTN>
The value of calibrated attenuation for the VOA expressed in dBm. The range is 0.0 to +30.0. VOAATTN is a float.
<VOAPWR>
The value of calibrated output power that the VOA is going to set as a result of its attenuation. VOAPWR is a float.
<CALOPWR>
The value of the calibrated optical power expected for the line added to the calculated value which equals the total expected output power. Expressed in dBm. Defaults to 0 dBm. CALOPWR is a float.
<CHPOWER>
The value of per-channel optical power. Float expressed in dBm. The parameter type is REVERTIVE_TIME (revertive time)
•
Revertive time is 0.5 to 12.0 minutes.
<NAME>
Port name. NAME is a string.
<SOAK>
SOAK is an integer. Defaults to 8.
<CMDMDE>
Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.35 ED-OSC
(Cisco ONS 15454) The Edit Optical Service Channel (ED-OSC) command edits the optical service channel (OSC) group attributes.
Usage Guidelines
None
CategoryDWDM
SecurityProvisioning
Input FormatED-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>];
Input ExampleED-OSC:PENNGROVE:OSC-1:114:::RINGID=1,NODEID=10;
Input Parameters
<AID>
Access identifier from the "OSC" section.
<RINGID>
The OSC ring ID of the NE, up to six characters. Valid characters are A-Z and 0-9. String. Default value is "# of AID OSC-#". RINGID is an integer.
<NODEID>
The OSC node ID of the NE. NODEID ranges from 0 to 31. NODEID is an integer.
11.36 ED-OTS
(Cisco ONS 15454) The Edit Optical Transport Section (ED-OTS) command edits the attributes (service parameters) and state of an OTS facility.
Usage Guidelines
None
CategoryDWDM
SecurityProvisioning
Input FormatED-OTS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[VOAATTN=<VOAATTN>],
[VOAPWR=<VOAPWR>],[OFFSET=<OFFSET>],[CALTILT=<CALTILT>],[OSRI=<OSRI>],
[AMPLMODE=<AMPLMODE>],[CHPOWER=<CHPOWER>],[EXPGAIN=<EXPGAIN>],
[NAME=<NAME>],[SOAK=<SOAK>],[CMDMDE=<CMDMDE>]:<PST>,[<SST>];Input ExampleED-OTS:PENNGROVE:LINE-6-1:114:::RDIRN=W-E,VOAATTN=5.0,VOAPWR=10.0,OFFSET=0.0,CALTILT=0.0,OSRI=N,AMPLMODE=GAIN,CHPOWER=10.0,EXPGAIN=-5.0,
NAME="OTS PORT",SOAK=8,CMDMDE=CMDMDE:IS,AINS;Input Parameters
<AID>
Access identifier from the "LINE" section.
<RDIRN>
Ring directionality of the optical line. The parameter type is RDIRN_MODE, which is the optical ring directionality.
•
The direction of the signal is from east to west (clockwise).
•
The direction of the signal is from west to east (counterclockwise).
<VOAATTN>
The value of calibrated attenuation for the VOA expressed in dBm. The range is 0.0 to +30.0. VOAATTN is a float.
<VOAPWR>
The value of calibrated output power that the VOA is going to set as a result of its attenuation. VOAPWR is a float.
<OFFSET>
The calibration value of the optical power added to the calculated reference value. Defaults to 0 dBm. OFFSET is a float.
<CALTILT>
(Optional) The amplifier calibration tilt offset to be added to the calculated reference value. Defaults to 0 dBm. CALTILT is a float.
<OSRI>
(Optional) Optical safety remote interlock (OSRI) is enabled or disabled. Present only on a port where the OSRI is supported. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<AMPLMODE>
The optical amplification control mode. The parameter type is AMPL_MODE, which defines the amplifier control mode.
•
The amplifier always maintains a fixed gain.
•
The amplifier maintains the output power to a fixed value.
<CHPOWER>
The per-channel optical power. CHPOWER is a float.
<EXPGAIN>
The gain expected value to be reached from an amplifier when the node is part of a DWDM access network. EXPGAIN is a float.
<NAME>
The name of the port. NAME is a string.
<SOAK>
SOAK is an integer. It defaults to 8.
<CMDMDE>
Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.37 ED-PID
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Password (ED-PID) command allows a user to change his or her own password.
Usage Guidelines
•
•
•
ED-PID:[TID]:<UID>:[CTAG]::<OLDPID>,<NEWPID>;
The syntax of OLDPID is not checked. The NEWPID is required to follow Telcordia standards (for example, 10 characters maximum including 1 letter, 1 number, and any one of the following characters: #, %, or +). The OLDPID must match what is in the database.
You must use the ED-USER-SECU command to change the default password for the CISCO15 superuser.
•
CategorySecurity
SecurityRetrieve
Input FormatED-PID:[<TID>]:<UID>:<CTAG>::<OLDPID>,<NEWPID>;
Input ExampleED-PID:CISCO:UID:123::OLDPWD,NEWPWD;
Input Parameters
11.38 ED-POS
(Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Packet-Over-SONET (ED-POS) command edits the back-end port information for the Ethernet card when the back-end port is working in POS mode. The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command to retrieve them. ED-POS cannot set ENCAP and PST/SST.
Usage Guidelines
This command is supported for the ONS 15454 CE-100T-8 and CE-1000-4 cards, the ONS 15310-CL ML-100T-8 and CE-100T-8 cards, and the ONS 15600 ASAP card.
CategoryPorts
SecurityProvisioning
Input FormatED-POS:[<TID>]:<AID>:<CTAG>:::[ENCAP=<ENCAP>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];Input ExampleED-POS:CISCO:VFAC-2-0:123:::ENCAP=HDLC,NAME=NAME,CMDMDE=CMDMDE,
SOAK=32:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<ENCAP>
Encapsulation. The parameter type is ENCAP, which is the frame encapsulation type.
•
GFP frame mode
•
GFP transparent mode
•
HDLC frame mode
•
HDLC LAN extension frame mode
•
HDLC X.86 frame mode
<NAME>
Port name. NAME is a string.
<CMDMDE>
Command Mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from IS-NR or OOS-AU,AINS service state. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<SOAK>
OOS-AINS to IS transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.39 ED-PROTOCOL
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Protocol (ED-PROTOCOL) command is used to enable/disable a protocol/service that is supported in the NE. Valid protocols include shell/file system access (SHELL), EMS, TL1, and Simple Network Management Protocol (SNMP).
Usage Guidelines
•
•
CategorySecurity
SecuritySuperuser
Input FormatED-PROTOCOL:[<TID>]:<PROTOCOLAID>:<CTAG>::<PROTOCOLSTAT>;
Input ExampleED-PROTOCOL:CISCONODE:EMS:123::SECURE;
Input Parameters
11.40 ED-ROLL-<MOD_PATH>
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Roll for STS1, STS12C, STS192C, STS24C, STS3C, STS48C, STS6C, STS9C, VT1, or VT2 (ED-ROLL-<MOD_PATH>) command forces a rolling operation. Force attempts to force a valid signal to complete the rolling operation.
Usage Guidelines
See Table 27-1 for supported modifiers by platform.
Note
CategoryBridge and Roll
SecurityProvisioning
Input FormatED-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>:::[CMDMDE=<CMDMDE>];
Input ExampleED-ROLL-STS1:CISCO:STS-1-1-1,STS-2-1-1:1:::CMDMDE=FRCD;
Input Parameters
<FROM>
Source access identifier from the "CrossConnectId1" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, then this termination point (leg) should be the FROM-AID termination point. Otherwise, FROM is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters.
<TO>
Destination access identifier from the "CrossConnectId1" section. It is one of the termination points (legs) of the existing cross-connection. If the existing cross-connection is one-way, then this termination point (leg) should be the TO-AID termination point. Otherwise, the TO is not significant. FROM and TO should be entered as they are entered in the ENT-CRS command. You can issue RTRV-CRS command, and use the response for FROM and TO parameters.
<CMDMDE>
Command execution mode. Defaults to NORM.
Note
The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
11.41 ED-SLV-WDMANS
(Cisco ONS 15454) The Edit Span Loss Verification Wavelength Division Multiplexing Automatic Node Set-Up (ED-SLV-WMANS) command edits the expected span loss verification.
Usage Guidelines
None
CategoryDWDM
SecurityMaintenance
Input FormatED-SLV-WDMANS:[<TID>]:<AID>:<CTAG>:::[HIGHSLVEXP=<HIGHSLVEXP>],
[LOWSLVEXP=<LOWSLVEXP>];Input ExampleED-SLV-WDMANS:VA454-22:WDMANS-E:116:::HIGHSLVEXP=10.0,LOWSLVEXP=5.0;
Input Parameters
<AID>
Access identifier from the "WDMANS" section.
<HIGHSLVEXP>
The high range value of the expected span loss verification. HIGHSLVEXP is a float.
<LOWSLVEXP>
The low range value of the expected span loss verification. LOWSLVEXP is a float.
11.42 ED-SYNCN
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Synchronization (ED-SYNCN) command edits the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock. For each clock, up to three synchronization sources might be specified (for example, PRIMARY, SECOND, THIRD).To view or edit the system timing mode, use the RTRV-NE-SYNCN or ED-NE-SYNCN commands.
Usage Guidelines
To retrieve/set the timing mode, SSM message set, or quality of RES information, use the RTRV-NE-SYNCN and ED-NE-SYNCN commands.
CategorySynchronization
SecurityProvisioning
Input FormatED-SYNCN:[<TID>]:<AID>:<CTAG>:::[PRI=<PRI>],[SEC=<SEC>],[THIRD=<THIRD>][:];
Input ExampleED-SYNCN:BOYES:SYNC-NE:112:::PRI=INTERNAL,SEC=INTERNAL,THIRD=INTERNAL;
Input Parameters
<AID>
Access identifier from the "SYNC_REF" section.
<PRI>
Primary reference of the synchronization from the "SYN_SRC" section.
<SEC>
Secondary reference of the synchronization from the "SYN_SRC" section.
<THIRD>
Third reference of the synchronization from the "SYN_SRC" section.
11.43 ED-T1
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA) The Edit Digital Signal Facility (ED-T1) command edits the attributes related to a DS1/T1 port.
Usage Guidelines
•
•
•
•
•
•
•
•
•
CategoryPorts
SecurityProvisioning
Input FormatED-T1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SOAK=<SOAK>],[SFBER=<SFBER>],
[SDBER=<SDBER>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],
[RETIME=<RETIME>],[NAME=<NAME>],[MODE=<MODE>],[SYNCMAP=<SYNCMAP>],
[ADMSSM=<ADMSSM>],[VTMAP=<VTMAP>],[INHFELPBK=<INHFELPBK>],
[AISONLPBK=<AISONLPBK>],[CMDMDE=<CMDMDE>],
[AISVONAIS=<AISVONAIS>]:[<PST>[,<SST>]];Input ExampleED-T1:CISCO:FAC-2-1:1223:::LINECDE=AMI,FMT=ESF,LBO=0-131,TACC=8,
TAPTYPE=SINGLE,SOAK=10,SFBER=1E-4,SDBER=1E-6,SYNCMSG=Y,SENDDUS=Y,
RETIME=Y,NAME="T1PORT",MODE=FDL,SYNCMAP=ASYNC,ADMSSM=STU,
VTMAP=GR253,INHFELPBK=N,AISONLPBK=AIS_ON_LPBK_ALL,CMDMDE=CMDMDE,
AISVONAIS=Y:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<LINECDE>
Line code. The parameter type is LINE_CODE.
•
Line code value is AMI.
•
Line code value is B8ZS.
<FMT>
Digital signal frame format. The parameter type is FRAME_FORMAT, which is the frame format for a T1 port.
•
Frame format is D4.
•
Frame format is ESF.
•
Frame format is unframed.
<LBO>
Line build-out settings. The parameter type is LINE_BUILDOUT.
•
Line build-out range is 0-131.
•
Line build-out range is 132-262.
•
Line build-out range is 263-393.
•
Line build-out range is 394-524.
•
Line build-out range is 525-655.
<TACC>
TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Default is N. TACC is an integer.
<TAPTYPE>
TAP type. Defaults to DUAL. The parameter type is TAPTYPE (test access point type).
•
Dual FAD
•
Single FAD
<SOAK>
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<SFBER>
The port signal failure threshold. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
Port signal degrade threshold. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<SYNCMSG>
Synchronization status messaging is enabled or disabled on the T1 facility.
Note
The parameter type is YES_NO, which indicates whether the user's password is about to expire, the user is logged into the NE, or the user is locked out of the NE.
•
No
•
Yes
<SENDDUS>
The facility will send the DUS value as the SSM for that facility.
Note
The parameter type is YES_NO, which indicates whether the user's password is about to expire, the user is logged into the NE, or the user is locked out of the NE.
•
No
•
Yes
<RETIME>
Indicates if retiming is needed.
Note
The parameter type is YES_NO, which indicates whether the user's password is about to expire, the user is logged into the NE, or the user is locked out of the NE.
•
No
•
Yes
<NAME>
Name. NAME is a string.
<MODE>
Mode. Default value is FDL. The parameter type is DS1MODE, which is the DS1 path mode of the DS3XM-12 card.
•
Indicates that the DS1 path of the DS3XM-12 is in AT&T 54016 mode.
•
Indicates that the DS1 path of the DS3XM-12 is in FDL T1-403 mode.
<SYNCMAP>
The synchronous mapping for the DS1 facility. Defaults to ASYNC. Only supported on ONS 15454. The parameter type is SYNCMAP (synchronous mapping type).
•
Asynchronous
•
Mapping in byte
•
Mapping in jbyte
<ADMSSM>
The administrative synchronization status message. Only supported on the ONS 15454. Defaults to STU. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level.
•
Do Not Use For Synchronization
•
Primary Reference Source, Stratum 1 Traceable
•
Reserved For Network Synchronization Use
•
SONET Minimum Clock Traceable
•
Stratum 2 Traceable
•
Stratum 3 Traceable
•
Stratum 3E Traceable
•
Stratum 4 Traceable
•
Synchronized, Traceability Unknown
•
Transit Node Clock (2nd Generation Only)
<VTMAP>
The port to VT mapping type for that particular STS. Only supported on ONS 15454. Defaults to GR253. The parameter type is VTMAP (VT mapping).
•
Mapping based on Telcordia GR-253.
•
Mapping based on industry standard.
<INHFELPBK>
Indicates whether far-end loopbacks are inhibited on the facility. Only supported on the ONS 15454. Defaults to N. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<AISONLPBK>
Defaults to AIS_ON_LPBK_ALL. The parameter type is AIS_ON_LPBK, which indicates if AIS is sent on a loopback.
•
AIS is sent on facility loopbacks.
•
AIS is sent on all loopbacks.
•
AIS is not sent on loopbacks.
•
AIS is sent on terminal loopbacks.
<CMDMDE>
Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<AISVONAIS>
Defaults to N. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.44 ED-T3
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA) The Edit Digital Signal Facility (ED-T3) command edits the attributes related to a DS3/T3 port and the DS3i-N-12 card.
Usage Guidelines
•
•
•
•
•
•
•
•
•
•
•
–
–
–
•
•
•
•
•
CategoryPorts
SecurityProvisioning
Input FormatED-T3:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>],[LINECDE=<LINECDE>],[LBO=<LBO>],
[INHFELPBK=<INHFELPBK>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SOAK=<SOAK>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[NAME=<NAME>],[AISONLPBK=<AISONLPBK>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input ExampleED-T3:CISCO:FAC-1-2:123:::FMT=C-BIT,LINECDE=B3ZS,LBO=0-225,INHFELPBK=N,
TACC=8,TAPTYPE=SINGLE,SOAK=10,SFBER=1E-4,SDBER=1E-6,NAME="T3 PORT",
AISONLPBK=AIS_ON_LPBK_ALL,CMDMDE=CMDMDE:IS,AINS;Input Parameters
<AID>
Access identifier from the "FACILITY" section.
<FMT>
Digital signal frame format. The unframed value of the framing format is only supported for the DS3E card. The parameter type is DS_LINE_TYPE, which is the DS123 line type.
•
C-BIT line type applies to the DS3XM and DS3E cards.
•
M13 line type applies to the DS3XM and DS3E cards.
•
Line type is unframed. The old DS3 (L3M) and DS3CR cards can only run in unframed mode.
<LINECDE>
Line code. The parameter type is DS_LINE_CODE, which is the DS123 line code.
•
Bipolar with three-zero substitution
<LBO>
Line build-out settings. LBO is an integer. The parameter type is E_LBO, which is the electrical signal line build-out.
•
Electrical signal line build-out range is 1-225.
•
Electrical signal line build-out range is 226-450.
<INHFELPBK>
(Optional) Far-end loopback inhibition attribute of the port. If it is Y, the automatic far-end loopbacks are inhibited. It is either on or off. The system default is N. The parameter type is ON_OFF, which disables or enables an attribute.
•
Disable an attribute.
•
Enable an attribute.
<TACC>
TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Default is N. TACC is an integer.
<TAPTYPE>
TAP type. Defaults to DUAL. The parameter type is TAPTYPE, which is the test access point type.
•
Dual FAD
•
Single FAD
<SOAK>
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<SFBER>
The port signal failure threshold. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•
SFBER is 1E-3.
•
SFBER is 1E-4.
•
SFBER is 1E-5.
<SDBER>
Port signal degrade threshold. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•
SDBER is 1E-5.
•
SDBER is 1E-6.
•
SDBER is 1E-7.
•
SDBER is 1E-8.
•
SDBER is 1E-9.
<NAME>
Name. NAME is a string.
<AISONLPBK>
The parameter type is AIS_ON_LPBK, which indicates whether. AIS is sent on a loopback. Defaults to AIS_ON_LPBK_ALL.
•
AIS is sent on facility loopbacks.
•
AIS is sent on all loopbacks.
•
AIS is not sent on loopbacks.
•
AIS is sent on terminal loopbacks.
<CMDMDE>
Command mode. The parameter type is CMDMDE, which forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
PST
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
SST
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in-service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.45 ED-TRAPTABLE
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Trap Table (ED-TRAPTABLE) command edits a trap destination entry identified by a specific trap destination address.
Usage Guidelines
None
CategorySystem
SecurityProvisioning
Input FormatED-TRAPTABLE:[<TID>]:<AID>:<CTAG>:::COMMUNITY=<COMMUNITY>,
[TRAPPORT=<TRAPPORT>],[TRAPVER=<TRAPVER>];Input ExampleED-TRAPTABLE::1.2.3.4:1:::COMMUNITY="PUBLIC",TRAPPORT=162,TRAPVER=SNMPV1;
Input Parameters
<AID>
Access identifier from the "IPADDR" section. IP address identifying the trap destination.
<COMMUNITY>
Community name associated to the trap destination. Maximum of 32 characters. COMMUNITY is a string.
<TRAPPORT>
User datagram protocol (UDP) port number associated with the trap destination. Default to 162. TRAPPORT is an integer.
<TRAPVER>
SNMP version number. Defaults to SNMPv1. The parameter type is SNMP_VERSION (SNMP version).
•
SNMP version 1 (default)
•
SNMP version 2
11.46 ED-TRC-OCH
(Cisco ONS 15454) The Edit Trace Optical Channel Facility (ED-TRC-OCH) command edits trace-related optical channel facilities. Refer to the Cisco ONS SONET TL1 Reference Guide for specific card provisioning rules.
Usage Guidelines
None
CategoryDWDM
SecurityProvisioning
Input FormatED-TRC-OCH:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>],[TRC=<TRC>],
[TRCMODE=<TRCMODE>],[TRCLEVEL=<TRCLEVEL>],[TRCFORMAT=<TRCFORMAT>][:];Input ExampleED-TRC-OCH:CISCO:CHAN-6-2:10:::EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,
TRCLEVEL=TTI-PM,TRCFORMAT=64-BYTE;Input Parameters
<SRC>
Source access identifier from the "CHANNEL" section.
<EXPTRC>
Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). A null value is equivalent to ALL. EXPTRC is a string.
<TRC>
The path trace message to be transmitted. The trace byte continuously transmits a 64-byte, fixed-length, ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (Hex 00) and CR and LF. A null value is equivalent to ALL.
<TRCMODE>
Trace mode. Defaults to the OFF mode. The parameter type is TRCMODE (trace mode).
•
Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards.
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIM-P is detected.
•
Use the provisioned expected string as the expected string.
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.
•
Turn off path trace capability. Nothing will be reported.
<TRCLEVEL>
The trace level to be managed. TRCLEVEL is a string.
<TRCFORMAT>
Trace message size. The parameter type is TRCFORMAT (trace format).
•
1 byte trace message
•
16 byte trace message
•
64 byte trace message
•
Enable an attribute
11.47 ED-USER-SECU
(Cisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit User Security (ED-USER-SECU) command edits a user's privileges, password, or ID. Only a Superuser can perform this operation. Privilege levels are described in the ENT-USER-SECU command.
Usage Guidelines
•
•
•
ED-USER-SECU:[TID]:<UID>:[CTAG]::[<NEWUID>],[<NEWPID>],,[<UAP>]:;
–
–
–
–
•
–
<PID>=CISCO#234 /*PASSWORD ALREADY MEETS REQUIREMENTS*/ED-USER-SECU::CISCO2345:1::CISCO3456,CISCO#234,,PROV;
TCCP 1970-01-02 13:15:35 M 1 COMPLD ;
–
<UID> = CISCO40 <PID>=CISCO40 /*PASSWORD DOES NOT MEET REQUIREMENTS*/ED-USER-SECU::CISCO40:1::CISCO60,CISCO40,,PROV;
BRONCOS4 1970-01-02 13:14:24 M 1 DENY IIFM /* INVALID PASSWORD */ ;
•
•
CategorySecurity
SecuritySuperuser
Input FormatED-USER-SECU:[<TID>]:<UID>:<CTAG>::[<NEWUID>],[<NEWPID>],,[<UAP>][:];
Input ExampleED-USER-SECU:PETALUMA:CISCO15:123::NEWUID,NEWPID,,MAINT;
Input Parameters
11.48 ED-VCG
(Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA) The Edit Virtual Concatenated Group (ED-VCG) command edits the attributes of a VCG.
Usage Guidelines
None
CategoryVCAT
SecurityProvisioning
Input FormatED-VCG:[<TID>]:<SRC>:<CTAG>:::[TXCOUNT=<TXCOUNT>],[NAME=<NAME>];
Input ExampleED-VCG:NODE1:FAC-1-1:1234:::TXCOUNT=7,NAME="VCG2";
Input Parameters
<SRC>
Source access identifier from the "FACILITY" section.
<TXCOUNT>
Number of members in the transmit (Tx) direction. For ML1000-2 and ML100T-12 cards, the only valid value is 2. For the FC_MR-4 card, the only valid value is 8. TXCOUNT is an integer.
<NAME>
Name of the VCAT group. Maximum length is 64 characters. NAME is a string.
11.49 ED-WDMANS
(Cisco ONS 15454) The Edit Wavelength Division Multiplexing Automatic Node Set Up (ED-WDMANS) command edits the optical node set-up application (AONS) attributes.
Usage Guidelines
None
CategoryDWDM
SecurityMaintenance
Input FormatED-WDMANS:[<TID>]:<AID>:<CTAG>:::[POWER-IN=<POWERIN>],
[POWER-OUT=<POWEROUT>],[POWER-EXP=<POWEREXP>],[NTWTYPE=<NTWTYPE>];Input ExampleED-WDMANS:PENNGROVE:WDMANS-W:114:::POWERIN=10.0,POWEROUT=10.0,|
POWEREXP=10.0,NTWTYPE=METRO-CORE;Input Parameters
<AID>
Access identifier from the "WDMANS" section.
<POWERIN>
Input power for the OADM section or Mux/Demux for terminal nodes. POWERIN is a float.
<POWEROUT>
Output power for the OADM section or Mux/Demux for terminal nodes. POWEROUT is a float.
<POWEREXP>
Express power for the OADM section. POWEREXP is a float.
<NTWTYPE>
Network type where a DWDM node is installed. The parameter type is DWDM_RING_TYPE, which is the network type where the NE is installed.
•
The network where a DWDM node is installed is a metro access network.
•
The network where a DWDM node is installed is a metro core network.
•
The node does not have a standard DWDM configuration.
Posted: Thu Sep 13 02:34:39 PDT 2007
All contents are Copyright © 1992--2007 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
